Zotac G41 Motherboard Manual 6r675n
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report l4457
Overview 6h3y3j
& View Zotac G41 Motherboard Manual as PDF for free.
More details h6z72
- Words: 6,742
- Pages: 46
WARNING!
Electronic Emission Notices
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the is encouraged to try to correct the interference by one or more of the following measures: - - - -
REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the ’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. Copyright This manual is copyrighted with all rights reserved. No portion of this manual may be copied or reproduced by any means. While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the information contained herein. Trademarks All brand names, logos and ed trademarks mentioned are property of their respective owners.
1
G41 series motherboard
Table of Contents
Motherboard Specifications-------------------------------------------------------------------- 4 Motherboard Layout------------------------------------------------------------------------------ 6 Hardware Installation----------------------------------------------------------------------------- 8 Safety Instructions------------------------------------------------------------------------------ 8 Preparing the Motherboard--------------------------------------------------------------------- 9 Installing the U------------------------------------------------------------------------------- 9 Installing the U Fan------------------------------------------------------------------------- 10 Installing Memory Modules------------------------------------------------------------------- 10 Installing the Motherboard-------------------------------------------------------------------- 11 Installing the I/O Shield------------------------------------------------------------------------ 11 Securing the Motherboard into the chassis----------------------------------------------- 11 Connecting Cables and Setting Switches------------------------------------------------- 12 24-pin ATX Power ------------------------------------------------------------------------------ 13 4-pin ATX 12V Power - ------------------------------------------------------------------------ 13 Hard Disk Connector--------------------------------------------------------------------------- 14 SPK Header-------------------------------------------------------------------------------------- 14 SPDIF-Out Header----------------------------------------------------------------------------- 14 COM Header (Optional)----------------------------------------------------------------------- 14 Front Header----------------------------------------------------------------------------- 15 USB Headers------------------------------------------------------------------------------------ 16 F_Audio Header--------------------------------------------------------------------------------- 16 Connecting Serial ATA Cables (Optional)------------------------------------------------- 17 Fan Connectors--------------------------------------------------------------------------------- 17 Expansion Slots--------------------------------------------------------------------------------- 18 PCIE x16 Slot------------------------------------------------------------------------------- 18 PCIE x1 Slot--------------------------------------------------------------------------------- 18 PCI x1 Slot----------------------------------------------------------------------------------- 18 Jumper Settings--------------------------------------------------------------------------------- 19 Configuring the BIOS----------------------------------------------------------------------------- 20 Enter BIOS Setup------------------------------------------------------------------------------- 20 Main Menu---------------------------------------------------------------------------------------- 20 Advanced Menu--------------------------------------------------------------------------------- 21 U Configuration------------------------------------------------------------------------- 21 IDE Configuration-------------------------------------------------------------------------- 22 SuperIO Configuration --------------------------------------------------------------------22 Hardware Health Configuration--------------------------------------------------------- 22 AI Configuration------------------------------------------------------------------------ 22 MPS Configuration------------------------------------------------------------------------- 22 PCI Express Configuration--------------------------------------------------------------- 22 2
Table of Contents
Smbios Configuration--------------------------------------------------------------------- 22 Trusted Computing------------------------------------------------------------------------- 22 USB Configuration------------------------------------------------------------------------- 22 PCI/PnP Menu----------------------------------------------------------------------------------- 23 Boot Menu---------------------------------------------------------------------------------------- 24 Security Menu------------------------------------------------------------------------------------ 25 Chipset Menu------------------------------------------------------------------------------------ 26 Exit Menu----------------------------------------------------------------------------------------- 26 Flash Update Procedure --------------------------------------------------------------------- 27 Installing Drivers and Software--------------------------------------------------------------- 28 Drivers Installation - ------------------------------------------------------------------------------ 29 REALTEK HD AUDIO DRIVER SETUP ------------------------------------------------------ 34 Getting Started----------------------------------------------------------------------------------- 34 Sound Effect-------------------------------------------------------------------------------------- 34 Environment Simulation------------------------------------------------------------------ 34 Equalizer Selection - ---------------------------------------------------------------------- 35 Karaoke Mode------------------------------------------------------------------------------- 35 Mixer----------------------------------------------------------------------------------------------- 36 Playback control---------------------------------------------------------------------------- 36 Recording control--------------------------------------------------------------------------- 37 Audio I/O------------------------------------------------------------------------------------------ 38 Speaker Configuration-------------------------------------------------------------------- 39 Connector Settings------------------------------------------------------------------------- 40 S/PDIF ---------------------------------------------------------------------------------------- 40 Speaker Calibration------------------------------------------------------------------------ 41 Microphone--------------------------------------------------------------------------------------- 42 Noise Suppression------------------------------------------------------------------------- 42 Beam Forming------------------------------------------------------------------------------ 42 Acoustic Echo Cancellation-------------------------------------------------------------- 42 3D Audio Demo---------------------------------------------------------------------------------- 43 Information ---------------------------------------------------------------------------------- 43
3
G41 series motherboard
Motherboard Specifications
q Chipset v Intel® G41+ICH7 q Size v Micro ATX form factor of 8.9 inch x 7.05 inch q Microprocessor v s Intel® CoreTM 2 Quad/CoreTM 2 Duo/Pentium®/Celeron® Series processor v s Front Side Bus (FSB): 1333/1066/800 MT/s q Operating systems: v s Windows XP 32 bit/64 bit, Windows Vista 32 bit/64 bit and Windows 7 32bit/64bit q System Memory v s dual-channel (128 bits wide) DDRIII memory interface v s DDRIII 1066/800 v Maximum memory size: 8 GB q USB 2.0 Ports v s hot plug and play v Eight USB 2.0 ports (four on the back , four via the USB brackets connected to the internal USB headers) v s USB 2.0 protocol up to 480 Mbps transmission rate q Onboard Serial ATA II v Independent DMA operation on four ports (Optional) v Data transfer rates of 3 GB/S. q On board PCI Express LAN (RTL8103/RTL8111 series) v PCI Express base specification 1.0a compliant v Compliant to 802.3x flow control v 10/100 IEEE 802.3 compliant v Wake On LAN (WOL) power management v RTL8111 series is Gigabit Ethernet controller q Onboard High Definition Audio v s 6-channel v s Jack-Sensing function v One SPDIF-Out header on board q Green Function v SMM, APM, AI v Suspend to DRAM ed (Optional) v RTC timer to power-on the system v AC power failure recovery 4
Motherboard Specifications
q Onboard Graphics Features v DX9 and OpenGL 1.4 are ed v 3D Graphics Rendering Enhancements v Up to 2048x1536@75 Hz refresh v VGA/DVI port output q PCI Express Interface v PCI Express Generation 1.1 compatible v frequency of 1.25 GHz resulting in 2.5 GB/s each direction per lane. v Wake up function is ed q Expansion Slots v One PCI Express X16 slot v One PCI Express X1 slot (Optional) v One PCI bus master slot
5
G41 series motherboard
Motherboard Layout
Figure 1 shows the motherboard and Figure 2 shows the back connectors.
16 17 18 19
21
20
22
KB1 240
120
120
240
LOTES
R EM O V E
VGA USB
1.5V
UFAN1
CN1
DDRIII2
DDRIII1
121
SYSFAN1
CN6
FP _ S1
13 12
121
USB _ LAN
North Bridge
14 SD1
PW1
1.5V
PW2
15
JP2
2
PCIE2
PCIE1
11
South Bridge
PCI1
FP1
10 CN9
FP_U2
FP_U1
SATA4
SATA3
SATA2
SATA1 JP1
9 Figure 1.
8
6 5 4
Board Layout
1. 24-pin ATX Power Connector 2. IDE Connector 3. Front Header 4. Speaker Header 5. Clear CMOS Jumper 6. South Bridge 7. Serial-ATA (SATA) Connectors (Optional) 8. USB Headers 9. COM Header (Optional) 10. PCI Slot 11. PCIE x1 Slot (Optional) 6
7
SPK1
12. PCI Express x16 Slot 13. Front Audio Header 14. SPDIF-Out Header 15. Back Connectors 16. 4-pin ATX_12V Power Connector 17. System Fan Connector(Optional) 18. U Fan Connector 19. DVI-PCIEX16 Select Jumper 20. U Socket 21. North Bridge 22. DDRIII DIMM Sockets
3
Rear
Figure 2: Back connectors
7
5 6
10 15
11
3
2
4
5
6
1. PS/2 Mouse Port 2. PS/2 Keyboard Port 3. VGA Connector 4. DVI Port 5. USB Ports 6. Port Blue Green Pink
2-Channel Line-In Line-Out Mic In
4-Channel Rear Speaker Out Front Speaker Out Mic In
6-Channel Rear Speaker Out Front Speaker Out Center/Subwoofer
7. LAN Connector Lan Port with LEDs to indicate status. · Yellow/Light Up/Blink = 10 Mbps/Link/Activity · Yellow and Green/Light Up/Blink = 100 Mbps/link/Activity
7
G41 series motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics covered in this section are: q Preparing the motherboard
v Installing the U
v Installing the U fan v Installing the memory
q Installing the motherboard q Connecting cables and setting switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precautions. to remove power from your computer by disconnecting the AC main source before removing or installing any equipment from/to the computer chassis.
8
Hardware Installation
Preparing the Motherboard
The motherboard shipped in the box does not contain a U and memory. You need to purchase these to complete this installation.
Installing the U
Be very careful when handling the U. Make sure not to bend or break any pins on the back. Hold the processor only by the edges and do not touch the bottom of the processor. Use the following procedure to install the U onto the motherboard. 1. Unhook the socket lever by pushing down and away from the socket. 2. Lift the load plate. There is a protective socket cover on the load plate to protect the socket when there is no U installed. 3. Remove the protective socket cover from the load plate. 4. Remove the processor from its protective cover, making sure you hold it only by the edges. It is a good idea to save the cover so that whenever you remove the U, you have a safe place to store it. 5. Align the notches in the processor with the notches on the socket. 6. Lower the processor straight down into the socket with out tilting or sliding it into the socket. Note: Make sure the U is fully seated and level in the socket. 7. Close the load plate over the U and press down while you close and engage the socket lever.
9
G41 series motherboard
Installing the U Fan
There are many different fan types that can be used with this motherboard. Follow the instruction that came with your fan assembly. Be sure that the fan orientation is correct for your chassis type and your fan assembly.
Installing Memory Modules
This motherboard accommodates two memory modules. It can two 240-pin DDR3 1066/800. The total memory capacity is 8 GB. You must install at least one module in any of the two slots. Refer to the following recommendations to install the memory modules. q One DIMM: Install it into slot 1 or 2. You can install the DIMM into any slot, however, slot 1 is preferred. q Two DIMMs: Install them into slot 1 and slot 2. 120
240
120
240
DDRIII2
1.5V
1.5V
R EM O V E
LOTES
DDRIII1
121
121
Note that a memory module has a notch, so it can only fit in one direction. Refer to the following procedure to install memory modules into the slots on the motherboard. 1. Unlock a DIMM slot by pressing the module clips outward. 2. Align the memory module to the DIMM slot, and insert the module vertically into the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock the DIMM into the connector.
10
Hardware Installation
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis you are using and if you are replacing an existing motherboard or working with an empty chassis. Determine if it would be easier to make all the connections prior to this step or to secure the motherboard and then make all the connections. It is normally easier to secure the motherboard first. Use the following procedure to install the I/O shield and secure the motherboard into the chassis. Note: Be sure that the U fan assembly has enough clearance for the chassis covers to lock into place and for the expansion cards. Also make sure the U Fan assembly is aligned with the vents on the covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Before installing the motherboard, install the I/O shield from the inside of the chassis. Press the I/O shield into place and make sure it fits securely. If the I/O shield does not fit into the chassis, you would need to obtain the proper size from the chassis supplier.
Securing the Motherboard into the Chassis
Most computer chassis have a base with mounting studs or spacers to allow the motherboard to be secured to the chassis and help to prevent short circuits. If there are studs that do not align with a mounting hole on the motherboard, it is recommended that you remove that stud to prevent the possibility of a short circuit. In most cases, it is recommended to secure the motherboard with spacers. 1. Carefully place the motherboard onto the studs/spacers located inside the chassis. 2. Align the mounting holes with the studs/spacers. 3. Align the connectors to the I/O shield. 4. Ensure that the fan assembly is aligned with the chassis vents according to the fan assembly instruction. 5. Secure the motherboard with screws.
11
G41 series motherboard
Connecting Cables and Setting Switches
This section takes you through all the connectors and switch settings necessary on the motherboard. This will include: q Power Connections v 24-pin ATX power-PW1 v 4-pin ATX 12V power-PW2 q
onnecting Internal Headers C v Hard Disk Connector-CN1 v SPK Header-SPK1 v COM Header-CN9 (Optional) v Front Header-FP1 v USB Headers (FP_U1~FP_U2) v F_Audio Header-FP_S1 v SPDIF-Out Header-CN6
q Serial ATA II q Chassis Fans q Expansion slots q Jumper settings See Figure 1 to locate the connectors and jumpers referenced in the following procedure.
12
Hardware Installation
24-pin ATX Power-PW1
PW1 is the main power supply connector located along the edge of the board next to the DIMM slots. Make sure that the power supply cable and pins are properly aligned with the connector on the motherboard. Firmly plug the power supply cable into the connector and make sure it is secure. PW2 1
PW1-Pin Definition 240
120
240
Signal
Pin
Signal
1
+3.3V
13
+3.3V
2
+3.3V
14
-12V
3
GND
15
GND
4
+5V
16
PS_ON
5
GND
17
GND
6
+5V
18
GND
7
GND
19
GND
8
PWROK
20
-5V
9
+5V_AUX
21
+5V
10
+12V
22
+5V
11
+12V
23
+5V
12
+3.3V
24
GND
1.5V
1.5V
R EM O V E
LOTES
120
PW1 12 24
Pin
1
13
121
121
4-pin ATX 12V Power-PW2
PW2, the 4-pin ATX 12V power connection, is used to provide power to the U. Align the pins to the connector and press firmly until seated. PW2-Pin Definition Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
13
G41 series motherboard
Hard Disk Connector-CN1
The motherboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100/133 function. You can connect up to two hard disk drives, CD-ROM, 120MB Floppy (reserved for future BIOS) and other devices. 120
240
1.5V
1.5V
R EM O V E
240
LOTES
120
CN1 1 121
CN6
121
1
SPK Header SPK-Pin Definition
1
SPK1
1
CN9
Pin
Signal
1
VCC
2
NC
3
NC
4
SPK-
SPDIF-Out Header
This header provides a SPDIF (Sony/Philips Digital Interface)output to digital multimedia device through coaxial connector.
COM Header-CN9 (Optional)
SPDIF-Pin Definition
CN9 - Pin Definition
Pin
Signal
Pin
Signal
Pin
Signal
1
SPDIF OUTX
1
DCD
2
RXD
2
VCC
3
TXD
4
DTR
3
NC
5
GND
6
DSR
4
GND
7
RTS
8
CTS
9
RI
10
NC
14
Hardware Installation
Front Header-FP1
The front header on this motherboard is one connector used to connect the following four cables : q PWRLED Attach the front power LED cable to these two pins of the connector. The Power LED indicates the system’s status.
4
PW_LED-
GND
6
PWR_SW
7
RESET
8
GND
9
NC
10
KEY
1.5V
HDD_LED-
5
1.5V
3
R EM O V E
PW_LED+
121
Signal
2
LOTES
240
Pin
HDD_LED+
120
Signal
1
240
Pin
120
FP1-Pin Definition
121
FP1
1 Note: Some chassis do not have all four cables. Be sure to match the name on the connectors to the corresponding pins. q PWR SW Attach the power button cable from the case to these two pins. Pressing the power button on the front turns the system on and off rather than using the power supply button. q HDD LED Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED indicates the activity status of the hard disks. q RST SW Attach the Reset switch cable from the front of the case to these two pins. The system restarts when the RESET switch is pressed.
15
G41 series motherboard
USB Headers (FP_U1~FP_U2)
This motherboard contains four USB 2.0 ports that are exposed on the rear of the chassis (Figure 2). The motherboard also contains two 10-pin internal header connectors onboard. Note. Secure the bracket to either the front or rear of your chassis (not all chassis are equipped with the front option). 120
240
120
240
FP_U1~FP_U2-Pin Definition
1.5V
1.5V
LOTES
R EM O V E
PIN
Assignment
PIN
Assignment
1
VCC
2
VCC
3
USBP0-
4
USBP1-
5
USBP0+
6
USBP1+
7
GND
8
GND
9
KEY
10
NC
121
121
1
FP_S1
FP_U1 1
FP_U2 1
F_Audio Header
The audio connector s HD audio standard and provides two kinds of audio output choices: the Front Audio, the Rear Audio. The front Audio s re-tasking function. F_Audio-Pin Definition Pin
Signal
Pin
Signal
1
MIC(L)
6
Reserved
2
GND
7
FAVDIO-JD
3
MIC(R)
8
Key(No pin)
16
4
-ACZ-DET
9
Front Audio(L)
5
Front Audio(R)
10
Reserved
Note:
In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assignment on the cable is the same as the pin assignment on the mainboard header. To find out if the chassis you are buying s a front audio connector, please contract your dealer.
Hardware Installation
Connecting Serial ATA Cables (Optional)
The Serial ATA II connectors are used to connect the Serial ATA II device to the motherboard. These connectors the thin Serial ATA II cables for primary storage devices. The current Serial ATA II interface allows up to 3 GB/s data transfer rate.
TXP
Control
3
TXN
4
GND
5
RXN
121
Sense +12V GND
1.5V
1.5V
GND
R EM O V E
RXP
7
LOTES
6
240
1
120
2
Signal
240
GND
GND +12V Sense
Pin
120
UFAN1
SATA-Pin Definition
121
SYSFAN1
Fan Connectors
There are two fan connectors on the motherboard, including U fan connector-UFAN1 and System fan connector-SYSFAN1.
SATA4
SATA2
SATA3
SATA1
17
G41 series motherboard
Expansion Slots
The Intel G31 motherboard contains three expansion slots, one PCI Express x16 slot ,one PCI Express x1 slot (optional) and one PCI slot. For a full list of PCI Express x16 graphics card ed by this motherboard. 120
240
1.5V
1.5V
R EM O V E
240
LOTES
120
121
121
PCIE2 PCIE1 PCI1
PCIE x16 Slot-PCIE2 There is one PCIE x16 slot reserved for graphics or video cards that is fully compliant to PCIE 1.0a specification. PCIE x1 Slot-PCIE1 (Optional) There is one PCI Express x1 slot that is designed to accommodate less bandwidth intensive cards, such as a modem or LAN card. PCI Slot-PCI1 The one PCI slot many expansion cards such as a LAN card, USB card, SCSI card and other cards that comply with PCI specifications.
18
Hardware Installation
Jumper Settings
This chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. JP1-CMOS Clear Jumper JP1
Selection
1
1-2*
Normal*
1
2-3
CMOS Clear
If
you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) to clear date.
JP2-DVI-PCIEX16 Select Jumper JP2
Selection
1
1-2*
DVI*
1
2-3
PCIEX16
JP2 is a group containing twelve jumpers. Its default setting is DVI. When using the external graphics card, please change the jumper setting to PCIEX16.
Close
Open
* = Default setting.
Notice: 1. Be sure to save the CMOS setting when exit the CMOS. 2. If the U is frequency multiplier locked, no U speed change will be seen even if the frequency multiplier setting in CMOS setup is changed.
19
G41 series motherboard
Configuring the BIOS
This section discusses how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly setting the BIOS parameters is critical to maintain optimal system performance. Refer to the following procedure to /change BIOS settings. 1. Power on the computer., 2. Press the Del key when the following message briefly displays at the bottom of the screen during the Power On Self Test (POST).
Pressing Del takes you to the BIOS Setup Utility.
Note: 1. We reserve the right to update the BIOS version presented in the manual. The BIOS pictures shown in this section are for reference only. 2. It is strongly recommended that you do not change the default BIOS settings. Changing some settings could damage your system.
Main Menu
This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu.
Note: s please note that the data in gray is non-changeable, and the others are for selection. q q q q 20
AMI BIOS Displays the auto-detected BIOS information. Processor Displays the auto-detected U specification. System Memory Displays the auto-detected system memory. System time Allows you to set the system time.
Configuring the BIOS
Advanced Menu
The Advanced menu items allow you to change the setting for the U and other system devices. Press <enter> to display the configuration options:
U Configuration
The items in this menu show the U-related information that the BIOS automatically detects. Press <enter>to display the configuration options: q Configure advanced U settings Displays the auto-detected U information. q Hardware Prefetcher Use this item to enable or disable hardware prefetcher (hardware prefetch mechanism). q Adjacent Cache Line Prefetch Use this item to enable or disable the adjacent cache line prefetch mode. If you disable this item, only one 64-bit line will be prefetched from the 128-bit section (including the required data). If you enable this item, two lines will be prefetched whether there is required data or not. q Max UID Value Limit Allows you to determine whether to limit UID maximum value. Set this item to [Disable] Windows XP operating system; set this item to [Enable] for legacy operating system such as Windows NT4.0.. q Intel(R) Virtualization Tech Hardware Virtualization Technology enables processor feature for running multiple simultaneous virtual machines allowing specialized software applications to run in full isolation of each other. q Execute-Disable Bit Capability This function enhances protection of your computer , reducing exposure to viruses and malicious buffer overflow attacks when working with its ing software and system. q Core Multi-Processing Use this option to enable or disable Core Multi-Processing. q PECI Use this option to enable or disable PECI (Platform Environment Control Interface).
21
G41 series motherboard
IDE Configuration
The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Press <enter>to display the configuration options: q ATA/IDE Configuration The items allow you to configure ATA/IDE. q Configure SATA as This item allows you to set the SATA to IDE/RAID/AHCI mode. q Configure SATA Channels This item allows you to set the SATA channels [Before PATA] or [Behind PATA]. q Primary, Secondary, and Third IDE Master/Slave This displays the status of auto detection of IDE devices. q Hard Disk Write Protect This item will be effective only if device is accessed through BIOS. q IDE Detect Time Out (Sec) The item allows you to select the time out value for detecting ATA/ATAPI devices. q ATA(PI) 80pin cable detection The item allows you to select the mechanism for detecting 80pin ATA(PI) cable.
SuperIO Configuration
The items in this menu allow you to configure F71862 Super IO Chipset.
Hardware Health Configuration
This menu gives you an overview of the Hardware Health Configuration.
AI Configuration
The items in this menu allow you to set General AI Configuration, Advanced AI Configuration and Chipset AI Configuration.
MPS Configuration
The item in this menu allows you to select MPS revision. The default setting is 1.1.
PCI Express Configuration
The item in this menu allows you to enable or disable PCI Express L0s and L1 link power states.
Smbios Configuration
The item in this menu allows you to enable or disable Smbios Smi .
Trusted Computing
The item in this menu allows you to enable or disable TCG/TPM in BIOS.
USB Configuration
The items in this menu allow you to change the USB-related features .Press <enter> To display the configuration options: q Legacy USB Allows you to enable or disable for USB devices on legacy operating systems. q USB 2.0 Controller Mode Allows you to configure the USB 2.0 controller in HiSpeed or Full Speed. 22
Configuring the BIOS
q BIOS EHCI Hand-Off Allows you to enable for operating systems without an EHCI hand-off feature.
PCI/PnP Menu
The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/ PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Press <enter> to display the configuration options:
q Clear NVRAM The items allow you to select whether clear NVRAM during system boot. q Plug and Play O/S When set to [No], BIOS configure all the devices in the system. When set to [YES] and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot. q PCI Latency Timer Allows you to select the value in units of PCI clocks for PCI device latency timer . q Allocate IRQ to PCI VGA When set to [YES], BIOS assigns an IRQ to PCI VGA card if the requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested . q Palette Snooping When set to [Enabled], the pallete snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. q PCI IDE BusMaster When set to [Enabled], BIOS use PCI busmastering for reading/writing to IDE drives. q OffBoard PCI/ISA IDE Card Use this option to set the PCI slot number for some PCI IDE Cards holding. q IRQ3/4/5/7/9/10/11/14/15 These items allow you to set the Interrupt Request. q DMA Channel 0/1/3/5/6/7 Use these items to set the Direct Memory Access Channel. 23
G41 series motherboard
Boot Menu The Boot menu items allow you to change the system boot options. Press <enter> to display the configuration options:
Boot settings configuration
The items allow you to configure Boot settings. Press <enter> To display the configuration options: q Quick Boot Enabling this item allows the BIOS to skip some power on self tests while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. q Quiet Boot When set to [Disabled], displays normal POST message. When set to [Enabled], displays OEM Logo instead of POST messages. q AddOn ROM Display Mode Sets the display mode for option ROM. q Bootup Num-Lock Allows you to select the power-on state for the NumLock. q PS/2 Mouse Allows you to enable or disable for PS/2 mouse. q Wait for ‘F1’ If Error When set to [Enabled], the system waits for the F1 key to be pressed when error occurs. q Hit ‘DEL’ Message Display When set to [Enabled], the system displays the message “press DEL to run setup” during POST. q Interrupt 19 Capture When set to [Enabled], this function allows the option ROMS to trap interrupt 19.
24
Configuring the BIOS
Security Menu
The security menu items allow you to change the system security settings. Press <enter> to display the configuration options:
Change Supervisor/
Select this item to set or change the supervisor/ . The Supervisor/ item on top of the screen shows the default setting: [Not Installed]. After you set a , this item shows [Installed]. To set a Supervisor/ : 1. Select the item [Change Supervisor/ ] and press <Enter>. 2. From the box, type a composed of at least six letters and/or numbers, then press <Enter>. 3. Confirm the when prompted: The message “ Installed” appears after you successfully set your . To change the supervisor/ , follow the same steps as setting a use . To clear the supervisor/ , select the item [Change Supervisor/ ], then press <enter>. The message “ Uninstalled” appears.
Boot Sector Virus Protection
The item allows you to enable or disable boot sector virus protection.
25
G41 series motherboard
Chipset Menu
The chipset menu items allow you to change the advanced chipset settings. Press <enter> to display the sub-menu:
North bridge Configuration
The item allows you to configure north bridge features, including Memory, Graphics, PEG Port and so on.
South bridge Configuration
The item allows you to configure south bridge features, including USB, HDA, SMBUS, and so on.
U/Memory/GMCH voltage control
The items allow you to configure the U/memory/GMCH voltage.
U Over Clock
The item allows you to enable or disable U overclocking technology.
Exit Menu
The exit menu items allow you to load the option or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Press <enter> to display the sub-menu:
26
Configuring the BIOS
Save Changes and Exit
Select this item and press <Enter> to save the changes that you have made in the BIOS Setup and exit the BIOS Setup. When the diolog box [Save configuration changes and exit setup?] appears, select [Ok] to save and exit, or select [Cancel] to return to the main menu.
Discard Changes and Exit
Select this option only if you do not want to save the changes that you have made to the setup program. If you made changes to fields other than system date, system time, and , the BIOS asks for a confirmation before exiting.
Discard Changes
This option allows you to discard the selections you have made and restore the previously saved values. After selecting this option, a confirmation window appears. Select [Ok] to discard any change and load the previously saved values.
Load Optimal Defaults
This option allows you to load the default values for each of the parameters on the setup menus. When you select this option, a confirmation window appears. Select [Ok] to load default values. Select [Cancel] to make other changes before saving the values to the non-volatile RAM.
Load Failsafe Defaults
This option has been set by the manufacturer and represents settings which provide the minimum requirements for your system to operate.
FLASH Update Procedure
The program AFUDOS XX.ROM is included on the driver CD (D:\Utility\AFUDOS XX.ROM). Please follow the recommended procedure to update the flash BIOS, as listed below. 1. Create a DOS-bootable floppy diskette. Copy the new BIOS file (just obtained or ed) and the utility program AFUDOS XX.ROM to the diskette. 2. Allow the PC system to boot from the DOS diskette. 3. At the DOS prompt, type AFUDOS XX.ROM /P /C /B /N /X <ENTER> Note: XX (the BIOS file name) can be defined by s. 4. Wait until the flash-update is complete. 5. Restart the PC. Warning: - Do not turn off or RESET the computer during the flash process. - If you are not sure how to upgrade the BIOS, please take your computer to an Authorized Service Center and have a trained technician do the work for you.
27
G41 series motherboard
Installing Drivers and Software Note: It is important to that before installing the driver CD that is shipped in the kit, you need to load your operating system. The motherboard s Windows XP 32 bit/64 bit; Windows Vista 32 bit/64 bit and Windows 7 32bit/64bit. The kit comes with a CD that contains utility drivers and additional software. The CD that has been shipped with your Intel G41 motherboard contains the following software and drivers: q Intel chipset Driver q HDA sound Driver q Intel Graphics Driver q Realtek PCIE network Driver Note. We reserve the right to update the driver version presented in the manual. The driver installation pictures shown in this section are for reference only.
28
Installing Drivers and Software
Drivers Installation
1. Insert the Intel G41 driver CD into the drive after loading your operating system, and then you can see the interface below.
2. Follow the below for Software Installation Utility Installing.
29
G41 series motherboard
3. Follow the below for Intel graphics drive Installing.
30
Installing Drivers and Software
4. Follow the below for HDA sound driver installing.
31
G41 series motherboard
5. Follow the below for Realtek PCIE network driver installing.
32
Installing Drivers and Software
At last, you can open below page that provides information about the hardware devices on this motherboard, and check whether finish your installation.
33
G41 series motherboard
Realtek HD Audio Driver Setup Getting Started
After Realtek HD Audio Driver being installed (insert the driverCD and follow the onscreen instructions), “Realtek HD Audio Manager” icon will show in System tray as below. Double click the icon and the control will appear:
Sound Effect After clicking on the “Sound Effect” tab, 3 sections “Environment”, “Equalizer” and “Karaoke” are available for selection.
Environment Simulation You will be able to enjoy different sound experience by pulling down the arrow, totally 23 kinds of sound effect will be shown for selection. Realtek HD Audio Sound Manager also provides five popular settings “Stone Corridor”, “Bathroom”, “Sewer pipe”, “Arena” and “Audio Corridor” for quick enjoyment. 34
Installing Drivers and Software
Equalizer Selection The Equalizer section allows you to create your own preferred settings by utilizing this tool. In standard 10 bands of equalizer, ranging from 100Hz to 16KHz are available:
Frequently Used Equalizer Setting
Realtek recognizes the needs that you might have. By leveraging our long experience at audio field, Realtek HD Audio Sound Manager provides you certain optimized equalizer settings that are frequently used for your quick enjoyment. How to Use
Other than the buttons “Pop” “Live” “Club” & “Rock” shown on the page, to pull down the arrow in “Others” , you will find more optimized settings available to you. Karaoke Mode Karaoke mode brings Karaoke fun back home by simply using the music you usually play, Karaoke mode can help you eliminate the vocal of the song or adjust the key to accommodate your range. Vocal Cancellation:
Single click on “Voice Cancellation”, the vocals of the songs will be erased, while the background music is still playing which lets you take over the vocal part. Key Adjustment: Using “Up / Down Arrow” to find a key which better fits your vocal range.
35
G41 series motherboard
Mixer Realtek HD Audio Sound Manager integrates Microsoft’s “Volume Control” functions into the Mixer page. This gives you the advantage to you to create your favorite sound effect in one single tool.
Playback control
Mute
You may choose to mute single or multiple volume controls or to completely mute sound output. Tool √
Show the following volume control
This is to let you freely decide which volume control items to be displayed, total 13 items to be chosen.
√
Advanced controls
√
Enable playback multi-streaming
36
Installing Drivers and Software
With this function, you will be able to have an audio chat with your friends via headphone (stream 1 from front ) while still have music (stream 2 from back ) playing. At any given period, you can have maximum 2 streams operating simultaneously.
Recording control
Mute
You may choose to mute single or multiple volume controls or to completely mute sound input. Tool √ Show the following volume controls
This is to let you freely decide which volume control items to be displayed.
√ Advanced controls
Advanced control is a “Microphone Boost” icon. Once this item is checked, you will find “advanced” icon beside “Front Pink In” & “Mic Volume”. With this, the input signal into “Front Pink In” & “Mic Volume” will be strengthen.
√ Enable recording multi-streaming
At any given period, you can have maximum 2 streams operating simultaneously. 37
G41 series motherboard
Audio I/O Realtek HD Audio Manager frees you from default speaker settings. Different from before, for each jack, they are not limited to perform certain functions. Instead, now each jack is able to be chosen to perform either output (i.e. playback) function or input (i.e. Recording) function, we call this “Retasking”. Audio I/O aims to help you setting jacks as you wish. Moreover, other than blue to blue, pink to pink, the way that you used to do, Audio I/O would guide you to other right jacks that can also serve as microphone / speaker / headphone.
38
Installing Drivers and Software
Speaker Configuration Step 1: Plug in the device in any available jack. Step 2: Dialogue “connected device” will pop up for your selection. Please select the device you are trying to plug in. * If the device is being plugged into the correct jack, you will be able to find the icon beside the jack changed to the one that is same as your device. * If not correct, Realtek HD Audio Manager will guide you to plug the device into the correct jack.
39
G41 series motherboard
Connector Settings Click
to access connector settings
√ Mute rear when front headphone plugged in
Once this option is checked, whenever front headphone is plugged, the music that is playing from the back , will be stopped.
√ Disable front jack detection (option)
Did not find any function on front jacks? Please check if front jacks on your system are so-called AC’97 jacks. If so, please check this item to disable front jack detection.
√ Enable auto popup dialogue, when device has been plugged in.
Once this item checked, the dialog “Connected device”, would not automatically pop up when device plugged in.
S/PDIF Short for Sony/Philips Digital Interface, a standard audio file transfer format. S/PDIF allows the transfer of digital audio signals from one device to another without having to be converted first to an analog format. Maintaining the viability of a digital signal prevents the quality of the signal from degrading when it is converted to analog.
40
Installing Drivers and Software
√ Output Sampling Rate
- 44.1KHz: This is recommended while playing CD - 48KHz: This is recommended while playing DVD or Dolby. - 96KHz: This is recommended while playing DVD-Audio.
√ Output Source
- Output digital audio source: The digital audio format (such as .wav, .mp3, .midi etc) will come out through S/PDIF-Out. Speaker Calibration After you have successfully plugged in speakers and assigned to the right jacks, you are only one more step to go to enjoy the intended sound. We provide “Speaker Calibration” to help you check if the speakers are located in the correct position.
41
G41 series motherboard
Microphone This page is designed to provide you better microphone / recording quality. Below picture indicates both “Noise Suppression” & “Acoustic Echo Cancellation” are both enabled.
Noise Suppression If you feel that the background noise, especially the sound generated from the fan inside PC, is too loud? Try “Noise Suppression”, which allows you to cut off and suppress disturbing noise. Beam Forming Also known as “directional recording”, this option lets you do the following: Once beam forming is enabled; only the sound from certain direction will be recorded. You will get the best quality if you chose 90° position, which we recommend you to use, this effectively means that you speak right into the microphone. Note: A Stereo Microphone is required when using Beam Forming function. Acoustic Echo Cancellation This function prevents playback sound from being recorded by microphone together with your sound. For example, you might have chance to use VOIP function through Internet with your friends. The voice of your friend will come out from speakers (playback). However, the voice of your friend might also be recorded into your microphone then go back to your friend through Internet. In that case, your friend will hear his/her own voice again. With AEC (Acoustic Echo Cancellation) enabled at your side, your friend can enjoy the benefit with less echo.
42
Installing Drivers and Software
3D Audio Demo The section “3D Audio Demo” grants you another possibility to enjoy your sound. The Audio Demo allows you to listen to sound in an extraordinary way.
Information
This section provides information about your current system audio device.
43
G41 series motherboard
44
291-MA141-00
Electronic Emission Notices
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions contained in this manual, may cause harmful interference to radio and television communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the is encouraged to try to correct the interference by one or more of the following measures: - - - -
REORIENT OR RELOCATE THE RECEIVING ANTENNA INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT OF THE RECEIVER CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B requirements, or using an unshielded peripheral data cable, could also result in harmful interference to radio or television reception. The is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the ’s authority to operate this equipment. To ensure that the use of this product does not contribute to interference, it is necessary to use shielded I/O cables. Copyright This manual is copyrighted with all rights reserved. No portion of this manual may be copied or reproduced by any means. While every precaution has been taken in the preparation of this manual, no responsibility for errors or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the information contained herein. Trademarks All brand names, logos and ed trademarks mentioned are property of their respective owners.
1
G41 series motherboard
Table of Contents
Motherboard Specifications-------------------------------------------------------------------- 4 Motherboard Layout------------------------------------------------------------------------------ 6 Hardware Installation----------------------------------------------------------------------------- 8 Safety Instructions------------------------------------------------------------------------------ 8 Preparing the Motherboard--------------------------------------------------------------------- 9 Installing the U------------------------------------------------------------------------------- 9 Installing the U Fan------------------------------------------------------------------------- 10 Installing Memory Modules------------------------------------------------------------------- 10 Installing the Motherboard-------------------------------------------------------------------- 11 Installing the I/O Shield------------------------------------------------------------------------ 11 Securing the Motherboard into the chassis----------------------------------------------- 11 Connecting Cables and Setting Switches------------------------------------------------- 12 24-pin ATX Power ------------------------------------------------------------------------------ 13 4-pin ATX 12V Power - ------------------------------------------------------------------------ 13 Hard Disk Connector--------------------------------------------------------------------------- 14 SPK Header-------------------------------------------------------------------------------------- 14 SPDIF-Out Header----------------------------------------------------------------------------- 14 COM Header (Optional)----------------------------------------------------------------------- 14 Front Header----------------------------------------------------------------------------- 15 USB Headers------------------------------------------------------------------------------------ 16 F_Audio Header--------------------------------------------------------------------------------- 16 Connecting Serial ATA Cables (Optional)------------------------------------------------- 17 Fan Connectors--------------------------------------------------------------------------------- 17 Expansion Slots--------------------------------------------------------------------------------- 18 PCIE x16 Slot------------------------------------------------------------------------------- 18 PCIE x1 Slot--------------------------------------------------------------------------------- 18 PCI x1 Slot----------------------------------------------------------------------------------- 18 Jumper Settings--------------------------------------------------------------------------------- 19 Configuring the BIOS----------------------------------------------------------------------------- 20 Enter BIOS Setup------------------------------------------------------------------------------- 20 Main Menu---------------------------------------------------------------------------------------- 20 Advanced Menu--------------------------------------------------------------------------------- 21 U Configuration------------------------------------------------------------------------- 21 IDE Configuration-------------------------------------------------------------------------- 22 SuperIO Configuration --------------------------------------------------------------------22 Hardware Health Configuration--------------------------------------------------------- 22 AI Configuration------------------------------------------------------------------------ 22 MPS Configuration------------------------------------------------------------------------- 22 PCI Express Configuration--------------------------------------------------------------- 22 2
Table of Contents
Smbios Configuration--------------------------------------------------------------------- 22 Trusted Computing------------------------------------------------------------------------- 22 USB Configuration------------------------------------------------------------------------- 22 PCI/PnP Menu----------------------------------------------------------------------------------- 23 Boot Menu---------------------------------------------------------------------------------------- 24 Security Menu------------------------------------------------------------------------------------ 25 Chipset Menu------------------------------------------------------------------------------------ 26 Exit Menu----------------------------------------------------------------------------------------- 26 Flash Update Procedure --------------------------------------------------------------------- 27 Installing Drivers and Software--------------------------------------------------------------- 28 Drivers Installation - ------------------------------------------------------------------------------ 29 REALTEK HD AUDIO DRIVER SETUP ------------------------------------------------------ 34 Getting Started----------------------------------------------------------------------------------- 34 Sound Effect-------------------------------------------------------------------------------------- 34 Environment Simulation------------------------------------------------------------------ 34 Equalizer Selection - ---------------------------------------------------------------------- 35 Karaoke Mode------------------------------------------------------------------------------- 35 Mixer----------------------------------------------------------------------------------------------- 36 Playback control---------------------------------------------------------------------------- 36 Recording control--------------------------------------------------------------------------- 37 Audio I/O------------------------------------------------------------------------------------------ 38 Speaker Configuration-------------------------------------------------------------------- 39 Connector Settings------------------------------------------------------------------------- 40 S/PDIF ---------------------------------------------------------------------------------------- 40 Speaker Calibration------------------------------------------------------------------------ 41 Microphone--------------------------------------------------------------------------------------- 42 Noise Suppression------------------------------------------------------------------------- 42 Beam Forming------------------------------------------------------------------------------ 42 Acoustic Echo Cancellation-------------------------------------------------------------- 42 3D Audio Demo---------------------------------------------------------------------------------- 43 Information ---------------------------------------------------------------------------------- 43
3
G41 series motherboard
Motherboard Specifications
q Chipset v Intel® G41+ICH7 q Size v Micro ATX form factor of 8.9 inch x 7.05 inch q Microprocessor v s Intel® CoreTM 2 Quad/CoreTM 2 Duo/Pentium®/Celeron® Series processor v s Front Side Bus (FSB): 1333/1066/800 MT/s q Operating systems: v s Windows XP 32 bit/64 bit, Windows Vista 32 bit/64 bit and Windows 7 32bit/64bit q System Memory v s dual-channel (128 bits wide) DDRIII memory interface v s DDRIII 1066/800 v Maximum memory size: 8 GB q USB 2.0 Ports v s hot plug and play v Eight USB 2.0 ports (four on the back , four via the USB brackets connected to the internal USB headers) v s USB 2.0 protocol up to 480 Mbps transmission rate q Onboard Serial ATA II v Independent DMA operation on four ports (Optional) v Data transfer rates of 3 GB/S. q On board PCI Express LAN (RTL8103/RTL8111 series) v PCI Express base specification 1.0a compliant v Compliant to 802.3x flow control v 10/100 IEEE 802.3 compliant v Wake On LAN (WOL) power management v RTL8111 series is Gigabit Ethernet controller q Onboard High Definition Audio v s 6-channel v s Jack-Sensing function v One SPDIF-Out header on board q Green Function v SMM, APM, AI v Suspend to DRAM ed (Optional) v RTC timer to power-on the system v AC power failure recovery 4
Motherboard Specifications
q Onboard Graphics Features v DX9 and OpenGL 1.4 are ed v 3D Graphics Rendering Enhancements v Up to 2048x1536@75 Hz refresh v VGA/DVI port output q PCI Express Interface v PCI Express Generation 1.1 compatible v frequency of 1.25 GHz resulting in 2.5 GB/s each direction per lane. v Wake up function is ed q Expansion Slots v One PCI Express X16 slot v One PCI Express X1 slot (Optional) v One PCI bus master slot
5
G41 series motherboard
Motherboard Layout
Figure 1 shows the motherboard and Figure 2 shows the back connectors.
16 17 18 19
21
20
22
KB1 240
120
120
240
LOTES
R EM O V E
VGA USB
1.5V
UFAN1
CN1
DDRIII2
DDRIII1
121
SYSFAN1
CN6
FP _ S1
13 12
121
USB _ LAN
North Bridge
14 SD1
PW1
1.5V
PW2
15
JP2
2
PCIE2
PCIE1
11
South Bridge
PCI1
FP1
10 CN9
FP_U2
FP_U1
SATA4
SATA3
SATA2
SATA1 JP1
9 Figure 1.
8
6 5 4
Board Layout
1. 24-pin ATX Power Connector 2. IDE Connector 3. Front Header 4. Speaker Header 5. Clear CMOS Jumper 6. South Bridge 7. Serial-ATA (SATA) Connectors (Optional) 8. USB Headers 9. COM Header (Optional) 10. PCI Slot 11. PCIE x1 Slot (Optional) 6
7
SPK1
12. PCI Express x16 Slot 13. Front Audio Header 14. SPDIF-Out Header 15. Back Connectors 16. 4-pin ATX_12V Power Connector 17. System Fan Connector(Optional) 18. U Fan Connector 19. DVI-PCIEX16 Select Jumper 20. U Socket 21. North Bridge 22. DDRIII DIMM Sockets
3
Rear
Figure 2: Back connectors
7
5 6
10 15
11
3
2
4
5
6
1. PS/2 Mouse Port 2. PS/2 Keyboard Port 3. VGA Connector 4. DVI Port 5. USB Ports 6. Port Blue Green Pink
2-Channel Line-In Line-Out Mic In
4-Channel Rear Speaker Out Front Speaker Out Mic In
6-Channel Rear Speaker Out Front Speaker Out Center/Subwoofer
7. LAN Connector Lan Port with LEDs to indicate status. · Yellow/Light Up/Blink = 10 Mbps/Link/Activity · Yellow and Green/Light Up/Blink = 100 Mbps/link/Activity
7
G41 series motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics covered in this section are: q Preparing the motherboard
v Installing the U
v Installing the U fan v Installing the memory
q Installing the motherboard q Connecting cables and setting switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precautions. to remove power from your computer by disconnecting the AC main source before removing or installing any equipment from/to the computer chassis.
8
Hardware Installation
Preparing the Motherboard
The motherboard shipped in the box does not contain a U and memory. You need to purchase these to complete this installation.
Installing the U
Be very careful when handling the U. Make sure not to bend or break any pins on the back. Hold the processor only by the edges and do not touch the bottom of the processor. Use the following procedure to install the U onto the motherboard. 1. Unhook the socket lever by pushing down and away from the socket. 2. Lift the load plate. There is a protective socket cover on the load plate to protect the socket when there is no U installed. 3. Remove the protective socket cover from the load plate. 4. Remove the processor from its protective cover, making sure you hold it only by the edges. It is a good idea to save the cover so that whenever you remove the U, you have a safe place to store it. 5. Align the notches in the processor with the notches on the socket. 6. Lower the processor straight down into the socket with out tilting or sliding it into the socket. Note: Make sure the U is fully seated and level in the socket. 7. Close the load plate over the U and press down while you close and engage the socket lever.
9
G41 series motherboard
Installing the U Fan
There are many different fan types that can be used with this motherboard. Follow the instruction that came with your fan assembly. Be sure that the fan orientation is correct for your chassis type and your fan assembly.
Installing Memory Modules
This motherboard accommodates two memory modules. It can two 240-pin DDR3 1066/800. The total memory capacity is 8 GB. You must install at least one module in any of the two slots. Refer to the following recommendations to install the memory modules. q One DIMM: Install it into slot 1 or 2. You can install the DIMM into any slot, however, slot 1 is preferred. q Two DIMMs: Install them into slot 1 and slot 2. 120
240
120
240
DDRIII2
1.5V
1.5V
R EM O V E
LOTES
DDRIII1
121
121
Note that a memory module has a notch, so it can only fit in one direction. Refer to the following procedure to install memory modules into the slots on the motherboard. 1. Unlock a DIMM slot by pressing the module clips outward. 2. Align the memory module to the DIMM slot, and insert the module vertically into the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock the DIMM into the connector.
10
Hardware Installation
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis you are using and if you are replacing an existing motherboard or working with an empty chassis. Determine if it would be easier to make all the connections prior to this step or to secure the motherboard and then make all the connections. It is normally easier to secure the motherboard first. Use the following procedure to install the I/O shield and secure the motherboard into the chassis. Note: Be sure that the U fan assembly has enough clearance for the chassis covers to lock into place and for the expansion cards. Also make sure the U Fan assembly is aligned with the vents on the covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Before installing the motherboard, install the I/O shield from the inside of the chassis. Press the I/O shield into place and make sure it fits securely. If the I/O shield does not fit into the chassis, you would need to obtain the proper size from the chassis supplier.
Securing the Motherboard into the Chassis
Most computer chassis have a base with mounting studs or spacers to allow the motherboard to be secured to the chassis and help to prevent short circuits. If there are studs that do not align with a mounting hole on the motherboard, it is recommended that you remove that stud to prevent the possibility of a short circuit. In most cases, it is recommended to secure the motherboard with spacers. 1. Carefully place the motherboard onto the studs/spacers located inside the chassis. 2. Align the mounting holes with the studs/spacers. 3. Align the connectors to the I/O shield. 4. Ensure that the fan assembly is aligned with the chassis vents according to the fan assembly instruction. 5. Secure the motherboard with screws.
11
G41 series motherboard
Connecting Cables and Setting Switches
This section takes you through all the connectors and switch settings necessary on the motherboard. This will include: q Power Connections v 24-pin ATX power-PW1 v 4-pin ATX 12V power-PW2 q
onnecting Internal Headers C v Hard Disk Connector-CN1 v SPK Header-SPK1 v COM Header-CN9 (Optional) v Front Header-FP1 v USB Headers (FP_U1~FP_U2) v F_Audio Header-FP_S1 v SPDIF-Out Header-CN6
q Serial ATA II q Chassis Fans q Expansion slots q Jumper settings See Figure 1 to locate the connectors and jumpers referenced in the following procedure.
12
Hardware Installation
24-pin ATX Power-PW1
PW1 is the main power supply connector located along the edge of the board next to the DIMM slots. Make sure that the power supply cable and pins are properly aligned with the connector on the motherboard. Firmly plug the power supply cable into the connector and make sure it is secure. PW2 1
PW1-Pin Definition 240
120
240
Signal
Pin
Signal
1
+3.3V
13
+3.3V
2
+3.3V
14
-12V
3
GND
15
GND
4
+5V
16
PS_ON
5
GND
17
GND
6
+5V
18
GND
7
GND
19
GND
8
PWROK
20
-5V
9
+5V_AUX
21
+5V
10
+12V
22
+5V
11
+12V
23
+5V
12
+3.3V
24
GND
1.5V
1.5V
R EM O V E
LOTES
120
PW1 12 24
Pin
1
13
121
121
4-pin ATX 12V Power-PW2
PW2, the 4-pin ATX 12V power connection, is used to provide power to the U. Align the pins to the connector and press firmly until seated. PW2-Pin Definition Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
13
G41 series motherboard
Hard Disk Connector-CN1
The motherboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100/133 function. You can connect up to two hard disk drives, CD-ROM, 120MB Floppy (reserved for future BIOS) and other devices. 120
240
1.5V
1.5V
R EM O V E
240
LOTES
120
CN1 1 121
CN6
121
1
SPK Header SPK-Pin Definition
1
SPK1
1
CN9
Pin
Signal
1
VCC
2
NC
3
NC
4
SPK-
SPDIF-Out Header
This header provides a SPDIF (Sony/Philips Digital Interface)output to digital multimedia device through coaxial connector.
COM Header-CN9 (Optional)
SPDIF-Pin Definition
CN9 - Pin Definition
Pin
Signal
Pin
Signal
Pin
Signal
1
SPDIF OUTX
1
DCD
2
RXD
2
VCC
3
TXD
4
DTR
3
NC
5
GND
6
DSR
4
GND
7
RTS
8
CTS
9
RI
10
NC
14
Hardware Installation
Front Header-FP1
The front header on this motherboard is one connector used to connect the following four cables : q PWRLED Attach the front power LED cable to these two pins of the connector. The Power LED indicates the system’s status.
4
PW_LED-
GND
6
PWR_SW
7
RESET
8
GND
9
NC
10
KEY
1.5V
HDD_LED-
5
1.5V
3
R EM O V E
PW_LED+
121
Signal
2
LOTES
240
Pin
HDD_LED+
120
Signal
1
240
Pin
120
FP1-Pin Definition
121
FP1
1 Note: Some chassis do not have all four cables. Be sure to match the name on the connectors to the corresponding pins. q PWR SW Attach the power button cable from the case to these two pins. Pressing the power button on the front turns the system on and off rather than using the power supply button. q HDD LED Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED indicates the activity status of the hard disks. q RST SW Attach the Reset switch cable from the front of the case to these two pins. The system restarts when the RESET switch is pressed.
15
G41 series motherboard
USB Headers (FP_U1~FP_U2)
This motherboard contains four USB 2.0 ports that are exposed on the rear of the chassis (Figure 2). The motherboard also contains two 10-pin internal header connectors onboard. Note. Secure the bracket to either the front or rear of your chassis (not all chassis are equipped with the front option). 120
240
120
240
FP_U1~FP_U2-Pin Definition
1.5V
1.5V
LOTES
R EM O V E
PIN
Assignment
PIN
Assignment
1
VCC
2
VCC
3
USBP0-
4
USBP1-
5
USBP0+
6
USBP1+
7
GND
8
GND
9
KEY
10
NC
121
121
1
FP_S1
FP_U1 1
FP_U2 1
F_Audio Header
The audio connector s HD audio standard and provides two kinds of audio output choices: the Front Audio, the Rear Audio. The front Audio s re-tasking function. F_Audio-Pin Definition Pin
Signal
Pin
Signal
1
MIC(L)
6
Reserved
2
GND
7
FAVDIO-JD
3
MIC(R)
8
Key(No pin)
16
4
-ACZ-DET
9
Front Audio(L)
5
Front Audio(R)
10
Reserved
Note:
In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assignment on the cable is the same as the pin assignment on the mainboard header. To find out if the chassis you are buying s a front audio connector, please contract your dealer.
Hardware Installation
Connecting Serial ATA Cables (Optional)
The Serial ATA II connectors are used to connect the Serial ATA II device to the motherboard. These connectors the thin Serial ATA II cables for primary storage devices. The current Serial ATA II interface allows up to 3 GB/s data transfer rate.
TXP
Control
3
TXN
4
GND
5
RXN
121
Sense +12V GND
1.5V
1.5V
GND
R EM O V E
RXP
7
LOTES
6
240
1
120
2
Signal
240
GND
GND +12V Sense
Pin
120
UFAN1
SATA-Pin Definition
121
SYSFAN1
Fan Connectors
There are two fan connectors on the motherboard, including U fan connector-UFAN1 and System fan connector-SYSFAN1.
SATA4
SATA2
SATA3
SATA1
17
G41 series motherboard
Expansion Slots
The Intel G31 motherboard contains three expansion slots, one PCI Express x16 slot ,one PCI Express x1 slot (optional) and one PCI slot. For a full list of PCI Express x16 graphics card ed by this motherboard. 120
240
1.5V
1.5V
R EM O V E
240
LOTES
120
121
121
PCIE2 PCIE1 PCI1
PCIE x16 Slot-PCIE2 There is one PCIE x16 slot reserved for graphics or video cards that is fully compliant to PCIE 1.0a specification. PCIE x1 Slot-PCIE1 (Optional) There is one PCI Express x1 slot that is designed to accommodate less bandwidth intensive cards, such as a modem or LAN card. PCI Slot-PCI1 The one PCI slot many expansion cards such as a LAN card, USB card, SCSI card and other cards that comply with PCI specifications.
18
Hardware Installation
Jumper Settings
This chapter explains how to configure the motherboard’s hardware. Before using your computer, make sure all jumpers and DRAM modules are set correctly. Refer to this chapter whenever in doubt. JP1-CMOS Clear Jumper JP1
Selection
1
1-2*
Normal*
1
2-3
CMOS Clear
If
you want to clear the system configuration, use the JP1 (Clear CMOS Jumper) to clear date.
JP2-DVI-PCIEX16 Select Jumper JP2
Selection
1
1-2*
DVI*
1
2-3
PCIEX16
JP2 is a group containing twelve jumpers. Its default setting is DVI. When using the external graphics card, please change the jumper setting to PCIEX16.
Close
Open
* = Default setting.
Notice: 1. Be sure to save the CMOS setting when exit the CMOS. 2. If the U is frequency multiplier locked, no U speed change will be seen even if the frequency multiplier setting in CMOS setup is changed.
19
G41 series motherboard
Configuring the BIOS
This section discusses how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly setting the BIOS parameters is critical to maintain optimal system performance. Refer to the following procedure to /change BIOS settings. 1. Power on the computer., 2. Press the Del key when the following message briefly displays at the bottom of the screen during the Power On Self Test (POST).
Pressing Del takes you to the BIOS Setup Utility.
Note: 1. We reserve the right to update the BIOS version presented in the manual. The BIOS pictures shown in this section are for reference only. 2. It is strongly recommended that you do not change the default BIOS settings. Changing some settings could damage your system.
Main Menu
This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu.
Note: s please note that the data in gray is non-changeable, and the others are for selection. q q q q 20
AMI BIOS Displays the auto-detected BIOS information. Processor Displays the auto-detected U specification. System Memory Displays the auto-detected system memory. System time Allows you to set the system time.
Configuring the BIOS
Advanced Menu
The Advanced menu items allow you to change the setting for the U and other system devices. Press <enter> to display the configuration options:
U Configuration
The items in this menu show the U-related information that the BIOS automatically detects. Press <enter>to display the configuration options: q Configure advanced U settings Displays the auto-detected U information. q Hardware Prefetcher Use this item to enable or disable hardware prefetcher (hardware prefetch mechanism). q Adjacent Cache Line Prefetch Use this item to enable or disable the adjacent cache line prefetch mode. If you disable this item, only one 64-bit line will be prefetched from the 128-bit section (including the required data). If you enable this item, two lines will be prefetched whether there is required data or not. q Max UID Value Limit Allows you to determine whether to limit UID maximum value. Set this item to [Disable] Windows XP operating system; set this item to [Enable] for legacy operating system such as Windows NT4.0.. q Intel(R) Virtualization Tech Hardware Virtualization Technology enables processor feature for running multiple simultaneous virtual machines allowing specialized software applications to run in full isolation of each other. q Execute-Disable Bit Capability This function enhances protection of your computer , reducing exposure to viruses and malicious buffer overflow attacks when working with its ing software and system. q Core Multi-Processing Use this option to enable or disable Core Multi-Processing. q PECI Use this option to enable or disable PECI (Platform Environment Control Interface).
21
G41 series motherboard
IDE Configuration
The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Press <enter>to display the configuration options: q ATA/IDE Configuration The items allow you to configure ATA/IDE. q Configure SATA as This item allows you to set the SATA to IDE/RAID/AHCI mode. q Configure SATA Channels This item allows you to set the SATA channels [Before PATA] or [Behind PATA]. q Primary, Secondary, and Third IDE Master/Slave This displays the status of auto detection of IDE devices. q Hard Disk Write Protect This item will be effective only if device is accessed through BIOS. q IDE Detect Time Out (Sec) The item allows you to select the time out value for detecting ATA/ATAPI devices. q ATA(PI) 80pin cable detection The item allows you to select the mechanism for detecting 80pin ATA(PI) cable.
SuperIO Configuration
The items in this menu allow you to configure F71862 Super IO Chipset.
Hardware Health Configuration
This menu gives you an overview of the Hardware Health Configuration.
AI Configuration
The items in this menu allow you to set General AI Configuration, Advanced AI Configuration and Chipset AI Configuration.
MPS Configuration
The item in this menu allows you to select MPS revision. The default setting is 1.1.
PCI Express Configuration
The item in this menu allows you to enable or disable PCI Express L0s and L1 link power states.
Smbios Configuration
The item in this menu allows you to enable or disable Smbios Smi .
Trusted Computing
The item in this menu allows you to enable or disable TCG/TPM in BIOS.
USB Configuration
The items in this menu allow you to change the USB-related features .Press <enter> To display the configuration options: q Legacy USB Allows you to enable or disable for USB devices on legacy operating systems. q USB 2.0 Controller Mode Allows you to configure the USB 2.0 controller in HiSpeed or Full Speed. 22
Configuring the BIOS
q BIOS EHCI Hand-Off Allows you to enable for operating systems without an EHCI hand-off feature.
PCI/PnP Menu
The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/ PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Press <enter> to display the configuration options:
q Clear NVRAM The items allow you to select whether clear NVRAM during system boot. q Plug and Play O/S When set to [No], BIOS configure all the devices in the system. When set to [YES] and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot. q PCI Latency Timer Allows you to select the value in units of PCI clocks for PCI device latency timer . q Allocate IRQ to PCI VGA When set to [YES], BIOS assigns an IRQ to PCI VGA card if the requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested . q Palette Snooping When set to [Enabled], the pallete snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. q PCI IDE BusMaster When set to [Enabled], BIOS use PCI busmastering for reading/writing to IDE drives. q OffBoard PCI/ISA IDE Card Use this option to set the PCI slot number for some PCI IDE Cards holding. q IRQ3/4/5/7/9/10/11/14/15 These items allow you to set the Interrupt Request. q DMA Channel 0/1/3/5/6/7 Use these items to set the Direct Memory Access Channel. 23
G41 series motherboard
Boot Menu The Boot menu items allow you to change the system boot options. Press <enter> to display the configuration options:
Boot settings configuration
The items allow you to configure Boot settings. Press <enter> To display the configuration options: q Quick Boot Enabling this item allows the BIOS to skip some power on self tests while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. q Quiet Boot When set to [Disabled], displays normal POST message. When set to [Enabled], displays OEM Logo instead of POST messages. q AddOn ROM Display Mode Sets the display mode for option ROM. q Bootup Num-Lock Allows you to select the power-on state for the NumLock. q PS/2 Mouse Allows you to enable or disable for PS/2 mouse. q Wait for ‘F1’ If Error When set to [Enabled], the system waits for the F1 key to be pressed when error occurs. q Hit ‘DEL’ Message Display When set to [Enabled], the system displays the message “press DEL to run setup” during POST. q Interrupt 19 Capture When set to [Enabled], this function allows the option ROMS to trap interrupt 19.
24
Configuring the BIOS
Security Menu
The security menu items allow you to change the system security settings. Press <enter> to display the configuration options:
Change Supervisor/
Select this item to set or change the supervisor/ . The Supervisor/ item on top of the screen shows the default setting: [Not Installed]. After you set a , this item shows [Installed]. To set a Supervisor/ : 1. Select the item [Change Supervisor/ ] and press <Enter>. 2. From the box, type a composed of at least six letters and/or numbers, then press <Enter>. 3. Confirm the when prompted: The message “ Installed” appears after you successfully set your . To change the supervisor/ , follow the same steps as setting a use . To clear the supervisor/ , select the item [Change Supervisor/ ], then press <enter>. The message “ Uninstalled” appears.
Boot Sector Virus Protection
The item allows you to enable or disable boot sector virus protection.
25
G41 series motherboard
Chipset Menu
The chipset menu items allow you to change the advanced chipset settings. Press <enter> to display the sub-menu:
North bridge Configuration
The item allows you to configure north bridge features, including Memory, Graphics, PEG Port and so on.
South bridge Configuration
The item allows you to configure south bridge features, including USB, HDA, SMBUS, and so on.
U/Memory/GMCH voltage control
The items allow you to configure the U/memory/GMCH voltage.
U Over Clock
The item allows you to enable or disable U overclocking technology.
Exit Menu
The exit menu items allow you to load the option or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Press <enter> to display the sub-menu:
26
Configuring the BIOS
Save Changes and Exit
Select this item and press <Enter> to save the changes that you have made in the BIOS Setup and exit the BIOS Setup. When the diolog box [Save configuration changes and exit setup?] appears, select [Ok] to save and exit, or select [Cancel] to return to the main menu.
Discard Changes and Exit
Select this option only if you do not want to save the changes that you have made to the setup program. If you made changes to fields other than system date, system time, and , the BIOS asks for a confirmation before exiting.
Discard Changes
This option allows you to discard the selections you have made and restore the previously saved values. After selecting this option, a confirmation window appears. Select [Ok] to discard any change and load the previously saved values.
Load Optimal Defaults
This option allows you to load the default values for each of the parameters on the setup menus. When you select this option, a confirmation window appears. Select [Ok] to load default values. Select [Cancel] to make other changes before saving the values to the non-volatile RAM.
Load Failsafe Defaults
This option has been set by the manufacturer and represents settings which provide the minimum requirements for your system to operate.
FLASH Update Procedure
The program AFUDOS XX.ROM is included on the driver CD (D:\Utility\AFUDOS XX.ROM). Please follow the recommended procedure to update the flash BIOS, as listed below. 1. Create a DOS-bootable floppy diskette. Copy the new BIOS file (just obtained or ed) and the utility program AFUDOS XX.ROM to the diskette. 2. Allow the PC system to boot from the DOS diskette. 3. At the DOS prompt, type AFUDOS XX.ROM /P /C /B /N /X <ENTER> Note: XX (the BIOS file name) can be defined by s. 4. Wait until the flash-update is complete. 5. Restart the PC. Warning: - Do not turn off or RESET the computer during the flash process. - If you are not sure how to upgrade the BIOS, please take your computer to an Authorized Service Center and have a trained technician do the work for you.
27
G41 series motherboard
Installing Drivers and Software Note: It is important to that before installing the driver CD that is shipped in the kit, you need to load your operating system. The motherboard s Windows XP 32 bit/64 bit; Windows Vista 32 bit/64 bit and Windows 7 32bit/64bit. The kit comes with a CD that contains utility drivers and additional software. The CD that has been shipped with your Intel G41 motherboard contains the following software and drivers: q Intel chipset Driver q HDA sound Driver q Intel Graphics Driver q Realtek PCIE network Driver Note. We reserve the right to update the driver version presented in the manual. The driver installation pictures shown in this section are for reference only.
28
Installing Drivers and Software
Drivers Installation
1. Insert the Intel G41 driver CD into the drive after loading your operating system, and then you can see the interface below.
2. Follow the below for Software Installation Utility Installing.
29
G41 series motherboard
3. Follow the below for Intel graphics drive Installing.
30
Installing Drivers and Software
4. Follow the below for HDA sound driver installing.
31
G41 series motherboard
5. Follow the below for Realtek PCIE network driver installing.
32
Installing Drivers and Software
At last, you can open below page that provides information about the hardware devices on this motherboard, and check whether finish your installation.
33
G41 series motherboard
Realtek HD Audio Driver Setup Getting Started
After Realtek HD Audio Driver being installed (insert the driverCD and follow the onscreen instructions), “Realtek HD Audio Manager” icon will show in System tray as below. Double click the icon and the control will appear:
Sound Effect After clicking on the “Sound Effect” tab, 3 sections “Environment”, “Equalizer” and “Karaoke” are available for selection.
Environment Simulation You will be able to enjoy different sound experience by pulling down the arrow, totally 23 kinds of sound effect will be shown for selection. Realtek HD Audio Sound Manager also provides five popular settings “Stone Corridor”, “Bathroom”, “Sewer pipe”, “Arena” and “Audio Corridor” for quick enjoyment. 34
Installing Drivers and Software
Equalizer Selection The Equalizer section allows you to create your own preferred settings by utilizing this tool. In standard 10 bands of equalizer, ranging from 100Hz to 16KHz are available:
Frequently Used Equalizer Setting
Realtek recognizes the needs that you might have. By leveraging our long experience at audio field, Realtek HD Audio Sound Manager provides you certain optimized equalizer settings that are frequently used for your quick enjoyment. How to Use
Other than the buttons “Pop” “Live” “Club” & “Rock” shown on the page, to pull down the arrow in “Others” , you will find more optimized settings available to you. Karaoke Mode Karaoke mode brings Karaoke fun back home by simply using the music you usually play, Karaoke mode can help you eliminate the vocal of the song or adjust the key to accommodate your range. Vocal Cancellation:
Single click on “Voice Cancellation”, the vocals of the songs will be erased, while the background music is still playing which lets you take over the vocal part. Key Adjustment: Using “Up / Down Arrow” to find a key which better fits your vocal range.
35
G41 series motherboard
Mixer Realtek HD Audio Sound Manager integrates Microsoft’s “Volume Control” functions into the Mixer page. This gives you the advantage to you to create your favorite sound effect in one single tool.
Playback control
Mute
You may choose to mute single or multiple volume controls or to completely mute sound output. Tool √
Show the following volume control
This is to let you freely decide which volume control items to be displayed, total 13 items to be chosen.
√
Advanced controls
√
Enable playback multi-streaming
36
Installing Drivers and Software
With this function, you will be able to have an audio chat with your friends via headphone (stream 1 from front ) while still have music (stream 2 from back ) playing. At any given period, you can have maximum 2 streams operating simultaneously.
Recording control
Mute
You may choose to mute single or multiple volume controls or to completely mute sound input. Tool √ Show the following volume controls
This is to let you freely decide which volume control items to be displayed.
√ Advanced controls
Advanced control is a “Microphone Boost” icon. Once this item is checked, you will find “advanced” icon beside “Front Pink In” & “Mic Volume”. With this, the input signal into “Front Pink In” & “Mic Volume” will be strengthen.
√ Enable recording multi-streaming
At any given period, you can have maximum 2 streams operating simultaneously. 37
G41 series motherboard
Audio I/O Realtek HD Audio Manager frees you from default speaker settings. Different from before, for each jack, they are not limited to perform certain functions. Instead, now each jack is able to be chosen to perform either output (i.e. playback) function or input (i.e. Recording) function, we call this “Retasking”. Audio I/O aims to help you setting jacks as you wish. Moreover, other than blue to blue, pink to pink, the way that you used to do, Audio I/O would guide you to other right jacks that can also serve as microphone / speaker / headphone.
38
Installing Drivers and Software
Speaker Configuration Step 1: Plug in the device in any available jack. Step 2: Dialogue “connected device” will pop up for your selection. Please select the device you are trying to plug in. * If the device is being plugged into the correct jack, you will be able to find the icon beside the jack changed to the one that is same as your device. * If not correct, Realtek HD Audio Manager will guide you to plug the device into the correct jack.
39
G41 series motherboard
Connector Settings Click
to access connector settings
√ Mute rear when front headphone plugged in
Once this option is checked, whenever front headphone is plugged, the music that is playing from the back , will be stopped.
√ Disable front jack detection (option)
Did not find any function on front jacks? Please check if front jacks on your system are so-called AC’97 jacks. If so, please check this item to disable front jack detection.
√ Enable auto popup dialogue, when device has been plugged in.
Once this item checked, the dialog “Connected device”, would not automatically pop up when device plugged in.
S/PDIF Short for Sony/Philips Digital Interface, a standard audio file transfer format. S/PDIF allows the transfer of digital audio signals from one device to another without having to be converted first to an analog format. Maintaining the viability of a digital signal prevents the quality of the signal from degrading when it is converted to analog.
40
Installing Drivers and Software
√ Output Sampling Rate
- 44.1KHz: This is recommended while playing CD - 48KHz: This is recommended while playing DVD or Dolby. - 96KHz: This is recommended while playing DVD-Audio.
√ Output Source
- Output digital audio source: The digital audio format (such as .wav, .mp3, .midi etc) will come out through S/PDIF-Out. Speaker Calibration After you have successfully plugged in speakers and assigned to the right jacks, you are only one more step to go to enjoy the intended sound. We provide “Speaker Calibration” to help you check if the speakers are located in the correct position.
41
G41 series motherboard
Microphone This page is designed to provide you better microphone / recording quality. Below picture indicates both “Noise Suppression” & “Acoustic Echo Cancellation” are both enabled.
Noise Suppression If you feel that the background noise, especially the sound generated from the fan inside PC, is too loud? Try “Noise Suppression”, which allows you to cut off and suppress disturbing noise. Beam Forming Also known as “directional recording”, this option lets you do the following: Once beam forming is enabled; only the sound from certain direction will be recorded. You will get the best quality if you chose 90° position, which we recommend you to use, this effectively means that you speak right into the microphone. Note: A Stereo Microphone is required when using Beam Forming function. Acoustic Echo Cancellation This function prevents playback sound from being recorded by microphone together with your sound. For example, you might have chance to use VOIP function through Internet with your friends. The voice of your friend will come out from speakers (playback). However, the voice of your friend might also be recorded into your microphone then go back to your friend through Internet. In that case, your friend will hear his/her own voice again. With AEC (Acoustic Echo Cancellation) enabled at your side, your friend can enjoy the benefit with less echo.
42
Installing Drivers and Software
3D Audio Demo The section “3D Audio Demo” grants you another possibility to enjoy your sound. The Audio Demo allows you to listen to sound in an extraordinary way.
Information
This section provides information about your current system audio device.
43
G41 series motherboard
44
291-MA141-00
Related Documents 543cg
Zotac G41 Motherboard Manual 6r675n
November 2019 67
Msi Z77a-g41 Intel Z77 Motherboard Manual.pdf 2a3d8
December 2019 61
Manual Motherboard 6t4d4d
July 2021 0
Motherboard 65q4v
November 2022 0
Manual Motherboard P4m800pro-m 60121p
November 2019 65