Block-diagram-of-intel-8086 6z66a
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report l4457
Overview 6h3y3j
& View Block-diagram-of-intel-8086 as PDF for free.
More details h6z72
- Words: 1,020
- Pages: 5
www.eazynotes.com
Gursharan Singh Tatla
Block Diagram of Intel 8086 The 8086 U is divided into two independent functional units: 1. Bus Interface Unit (BIU) 2. Execution Unit (EU)
Fig. 1: Block Diagram of Intel 8086
Features of 8086 Microprocessor: 1. Intel 8086 was launched in 1978. 2. It was the first 16-bit microprocessor. 3. This microprocessor had major improvement over the execution speed of 8085. 4. It is available as 40-pin Dual-Inline-Package (DIP). 5. It is available in three versions: a. 8086 (5 MHz) b. 8086-2 (8 MHz)
Page No. 1
www.eazynotes.com
Gursharan Singh Tatla
Page No. 2
c. 8086-1 (10 MHz) 6. It consists of 29,000 transistors.
Bus Interface Unit (BIU) The function of BIU is to:
Fetch the instruction or data from memory.
Write the data to memory.
Write the data to the port.
Read data from the port.
Instruction Queue 1. To increase the execution speed, BIU fetches as many as six instruction bytes ahead to time from memory. 2. All six bytes are then held in first in first out 6 byte called instruction queue. 3. Then all bytes have to be given to EU one by one. 4. This pre fetching operation of BIU may be in parallel with execution operation of EU, which improves the speed execution of the instruction.
Execution Unit (EU) The functions of execution unit are:
To tell BIU where to fetch the instructions or data from.
To decode the instructions.
To execute the instructions.
The EU contains the control circuitry to perform various internal operations. A decoder in EU decodes the instruction fetched memory to generate different internal or external control signals required to perform the operation. EU has 16-bit ALU, which can perform arithmetic and logical operations on 8-bit as well as 16-bit.
General Purpose s of 8086 These s can be used as 8-bit s individually or can be used as 16-bit in pair to have AX, BX, CX, and DX.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 3
1. AX : AX is also known as accumulator that stores operands for arithmetic operation like divided, rotate. 2. BX : This is mainly used as a base . It holds the starting base location of a memory region within a data segment. 3. CX : It is defined as a counter. It is primarily used in loop instruction to store loop counter. 4. DX : DX is used to contain I/O port address for I/O instruction.
Segment s Additional s called segment s generate memory address when combined with other in the microprocessor. In 8086 microprocessor, memory is divided into 4 segments as follow:
Fig. 2: Memory Segments of 8086
1. Code Segment (CS): The CS is used for addressing a memory location in the Code Segment of the memory, where the executable program is stored. 2. Data Segment (DS): The DS contains most data used by program. Data are accessed in the Data Segment by an offset address or the content of other that holds the offset address. 3. Stack Segment (SS): SS defined the area of memory used for the stack.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 4
4. Extra Segment (ES): ES is additional data segment that is used by some of the string to hold the destination data.
Flag s of 8086 Flag in EU is of 16-bit and is shown in fig. 3:
Fig. 3: Flag of 8086
Flags determines the current state of the processor. They are modified automatically by U after mathematical operations, this allows to determine the type of the result, and to determine conditions to transfer control to other parts of the program. 8086 has 9 flags and they are divided into two categories: 1. Conditional Flags 2. Control Flags
Conditional Flags Conditional flags represent result of last arithmetic or logical instruction executed. Conditional flags are as follows:
Carry Flag (CF): This flag indicates an overflow condition for unsigned integer arithmetic. It is also used in multiple-precision arithmetic.
Auxiliary Flag (AF): If an operation performed in ALU generates a carry/barrow from lower nibble (i.e. D0 – D3) to upper nibble (i.e. D4 – D7), the AF flag is set i.e. carry given by D3 bit to D4 is AF flag. This is not a general-purpose flag, it is used internally by the processor to perform Binary to BCD conversion.
Parity Flag (PF): This flag is used to indicate the parity of result. If lower order 8-bits of the result contains even number of 1’s, the Parity Flag is set and for odd number of 1’s, the Parity Flag is reset.
Zero Flag (ZF): It is set; if the result of arithmetic or logical operation is zero else it is reset.
Sign Flag (SF): In sign magnitude format the sign of number is indicated by MSB bit. If the result of operation is negative, sign flag is set.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 5
Overflow Flag (OF): It occurs when signed numbers are added or subtracted. An OF indicates that the result has exceeded the capacity of machine.
Control Flags Control flags are set or reset deliberately to control the operations of the execution unit. Control flags are as follows: 1. Trap Flag (TP): a. It is used for single step control. b. It allows to execute one instruction of a program at a time for debugging. c. When trap flag is set, program can be run in single step mode. 2. Interrupt Flag (IF): a. It is an interrupt enable/disable flag. b. If it is set, the maskable interrupt of 8086 is enabled and if it is reset, the interrupt is disabled. c. It can be set by executing instruction sit and can be cleared by executing CLI instruction. 3. Direction Flag (DF): a. It is used in string operation. b. If it is set, string bytes are accessed from higher memory address to lower memory address. c. When it is reset, the string bytes are accessed from lower memory address to higher memory address.
Gursharan Singh Tatla
Block Diagram of Intel 8086 The 8086 U is divided into two independent functional units: 1. Bus Interface Unit (BIU) 2. Execution Unit (EU)
Fig. 1: Block Diagram of Intel 8086
Features of 8086 Microprocessor: 1. Intel 8086 was launched in 1978. 2. It was the first 16-bit microprocessor. 3. This microprocessor had major improvement over the execution speed of 8085. 4. It is available as 40-pin Dual-Inline-Package (DIP). 5. It is available in three versions: a. 8086 (5 MHz) b. 8086-2 (8 MHz)
Page No. 1
www.eazynotes.com
Gursharan Singh Tatla
Page No. 2
c. 8086-1 (10 MHz) 6. It consists of 29,000 transistors.
Bus Interface Unit (BIU) The function of BIU is to:
Fetch the instruction or data from memory.
Write the data to memory.
Write the data to the port.
Read data from the port.
Instruction Queue 1. To increase the execution speed, BIU fetches as many as six instruction bytes ahead to time from memory. 2. All six bytes are then held in first in first out 6 byte called instruction queue. 3. Then all bytes have to be given to EU one by one. 4. This pre fetching operation of BIU may be in parallel with execution operation of EU, which improves the speed execution of the instruction.
Execution Unit (EU) The functions of execution unit are:
To tell BIU where to fetch the instructions or data from.
To decode the instructions.
To execute the instructions.
The EU contains the control circuitry to perform various internal operations. A decoder in EU decodes the instruction fetched memory to generate different internal or external control signals required to perform the operation. EU has 16-bit ALU, which can perform arithmetic and logical operations on 8-bit as well as 16-bit.
General Purpose s of 8086 These s can be used as 8-bit s individually or can be used as 16-bit in pair to have AX, BX, CX, and DX.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 3
1. AX : AX is also known as accumulator that stores operands for arithmetic operation like divided, rotate. 2. BX : This is mainly used as a base . It holds the starting base location of a memory region within a data segment. 3. CX : It is defined as a counter. It is primarily used in loop instruction to store loop counter. 4. DX : DX is used to contain I/O port address for I/O instruction.
Segment s Additional s called segment s generate memory address when combined with other in the microprocessor. In 8086 microprocessor, memory is divided into 4 segments as follow:
Fig. 2: Memory Segments of 8086
1. Code Segment (CS): The CS is used for addressing a memory location in the Code Segment of the memory, where the executable program is stored. 2. Data Segment (DS): The DS contains most data used by program. Data are accessed in the Data Segment by an offset address or the content of other that holds the offset address. 3. Stack Segment (SS): SS defined the area of memory used for the stack.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 4
4. Extra Segment (ES): ES is additional data segment that is used by some of the string to hold the destination data.
Flag s of 8086 Flag in EU is of 16-bit and is shown in fig. 3:
Fig. 3: Flag of 8086
Flags determines the current state of the processor. They are modified automatically by U after mathematical operations, this allows to determine the type of the result, and to determine conditions to transfer control to other parts of the program. 8086 has 9 flags and they are divided into two categories: 1. Conditional Flags 2. Control Flags
Conditional Flags Conditional flags represent result of last arithmetic or logical instruction executed. Conditional flags are as follows:
Carry Flag (CF): This flag indicates an overflow condition for unsigned integer arithmetic. It is also used in multiple-precision arithmetic.
Auxiliary Flag (AF): If an operation performed in ALU generates a carry/barrow from lower nibble (i.e. D0 – D3) to upper nibble (i.e. D4 – D7), the AF flag is set i.e. carry given by D3 bit to D4 is AF flag. This is not a general-purpose flag, it is used internally by the processor to perform Binary to BCD conversion.
Parity Flag (PF): This flag is used to indicate the parity of result. If lower order 8-bits of the result contains even number of 1’s, the Parity Flag is set and for odd number of 1’s, the Parity Flag is reset.
Zero Flag (ZF): It is set; if the result of arithmetic or logical operation is zero else it is reset.
Sign Flag (SF): In sign magnitude format the sign of number is indicated by MSB bit. If the result of operation is negative, sign flag is set.
www.eazynotes.com
Gursharan Singh Tatla
Page No. 5
Overflow Flag (OF): It occurs when signed numbers are added or subtracted. An OF indicates that the result has exceeded the capacity of machine.
Control Flags Control flags are set or reset deliberately to control the operations of the execution unit. Control flags are as follows: 1. Trap Flag (TP): a. It is used for single step control. b. It allows to execute one instruction of a program at a time for debugging. c. When trap flag is set, program can be run in single step mode. 2. Interrupt Flag (IF): a. It is an interrupt enable/disable flag. b. If it is set, the maskable interrupt of 8086 is enabled and if it is reset, the interrupt is disabled. c. It can be set by executing instruction sit and can be cleared by executing CLI instruction. 3. Direction Flag (DF): a. It is used in string operation. b. If it is set, string bytes are accessed from higher memory address to lower memory address. c. When it is reset, the string bytes are accessed from lower memory address to higher memory address.
More Documents from "Ritesh Singh" q241u
Mudra For Hypothyroidism 1c252n
November 2022 0
Drug Of Choice In Various Diseases t533p
October 2019 55
Emirates Fare Conditions 4b211q
November 2019 46
Block-diagram-of-intel-8086 6z66a
November 2019 62
Tunnel Ventilation Design Solution 3a5n6j
November 2019 102