T-2007097 59xx

Detection and Control Components

FCM-1 Control Module (IQ-318/IQ-636X-2) Features • Built-in type identification automatically identifies these devices to the control unit • Internal circuitry and relay powered directly by two-wire SLC loop; requires power for notification • Integral LED blinks green each time a communication is received from the control unit and turns on in steady red when activated • LED blink may be deselected globally (affects all devices)

power supply is always relay isolated from the communication loop so that a trouble condition on the external power supply will never interfere with the rest of the system. Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the control , so as to differentiate between a module and a sensor address. The FCM-1 is used to switch 24 VDC audible/visual or releasing appliance power.

• High noise immunity (EMF/RFI) • Wide viewing angle of LED • SEMS screws with clamping plates for wiring ease • Direct-dial entry of address (01-159) • Audible/visual applications may be wired for Class B or A (Style Y or Z) • Face plate is made of off-white Noryl® • Configured for a single Class B (Style Y) or Class A (Style Z) Notification Appliance Circuit • FlashScan® communication protocol Applications The FCM-1 Addressable Control Module provides the AUTOPULSE IQ-318, or IQ-636X-2 control unit a circuit for Notification Appliances (horns, strobes, speakers, etc.). Addressability allows the FCM-1 to be activated, either manually or through programming, on a select (zone or area of coverage) basis.

Technical Information Normal Operating Voltage: . . . . . . . . . . . . . . . . 15 to 32 VDC Maximum Current Draw:. . . . . . . . . . . . . . . . 5.1 mA (LED on) Average Operating Current:. . . . . . . . . 390 μA (LED flashing) Maximum NAC Current Rating: Class B wiring system: . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A Class A wiring system:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2A External Supply Voltage . . . . . . . . max 80 volts (RMS or DC) between T3 and T4: Drain on External. . . . . . 2 μA max. (using internal EOL relay) Supply: EOL Resistance:. . . . . . . . . . . . . . . . . . . . . . . . . . . 47 K ohms Temperature Range:. . . . . . . . 32 °F to 120 °F (0 °C to 49 °C) Humidity Range: . . . . . . . . . . . . 10% to 93% non-condensing FCM-1 CONTROL MODULE

FlashScan (U.S. Patent 5,539,389) is a new communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of other designs.

ISOLATED QUADRANT

Description Each FCM-1 Control Module uses one of 159 possible module addresses on a SLC loop. It responds to regular polls from the control unit and reports its type and status, including the open/normal/short status of its Notification Appliance Circuit (NAC). The LED blinks with each poll received. On command, it activates its internal relay. The FCM-1 supervises Class B (Style Y) or Class A (Style Z) notification or control circuits. The FCM-1 can be used to replace the CMX-2 module, Part No. 417479, in existing systems. Upon code command from the unit, the FCM-1 will disconnect the supervision and connect the external power supply in the proper polarity across the load device. The disconnection of the supervision provides a positive indication to the that the control relay actually turned ON. The external

004749

Note: The CB500 barrier is required by UL for separating power-limited and non-power limited wiring in the same junction box.

3-29

FCM-1 MODULE

Ordering Information Part No. 428101 437066 419639 437071 436202

Description FCM-1 Intelligent Control Module FCM-1A Intelligent Control Module (ULC) Releasing Device, REL-47K Releasing Device, REL-47K BP (ULC) CB500 Barrier

Shipping Weight lb (kg) 1 (0.45) 1

(0.45)

0.5 1

(0.23) (0.45)

0.5

(0.23)

007271

Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS669 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM). . . . . . . 7300-0028:202 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457-99-E Maryland State Fire Marshal. . . . . . . . . . . . . . . Permit # 2020 USCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 * Listings and Approvals are under NOTIFIER.

TYPICAL CONNECTION OF A 24 VDC NOTIFICATION DEVICE TO THE FCM-1 MODULE 24 VDC CIRCUIT. DO NOT LOOP WIRE ON TERMINALS 10 & 11. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS. 24 VDC POWER SUPPLY ISOLATED, REGULATED, POWER LIMITED PER NFPA 70. LISTED FOR FIRE PROTECTION WITH BATTERY BACKUP.

CONNECT MODULES TO LISTED COMPATIBLE CONTROL S ONLY FROM OR PREVIOUS DEVICE

CONTROL MODULE

SIGNAL LINE CIRCUIT (SLC) 32 VDC MAXIMUM. TWISTED PAIR IS RECOMMENDED.

MODULE POLARITIES ARE SHOWN IN ALARM

47K EOL REESISTOR ELR-47K 008862

UL LISTED EOL RELAY SHOWN ENERGIZED 24 VDC COIL EOLR-1

TO NEXT CONTROL MODULE OR END-OFLINE RELAY. ONE RELAY REQUIRED FOR EACH CIRCUIT. SOME CONTROL S HAVE RELAY BUILT IN AND DO NOT REQUIRE EXTERNAL WIRING. REFER TO MANUAL.

TO NEXT DEVICE

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

FlashScan is a trademark of Honeywell International. Noryl is a ed trademark of GE Plastics, a subsidiary of General Electric Company.

TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411

Copyright © 2011 Tyco Fire Protection Products All rights reserved. Form No. T-2007097-3

Detection and Control Components FCM-1-REL(A) Releasing Control Module (IQ-318/IQ-636X-2) Features • Redundant protocol for added protection • Configurable for Class A or Class B operation • External supply voltage monitoring • Can power one 24V or two 12V solenoids • SEMS screws for easing wiring • controlled status LED • Analog communications • Rotary address switches • Low standby current • Mounts in standard 4 in. (10.16 cm) junction box • FlashScan® operation Description The FCM-1-REL(A) Releasing Control Module is specifically designed for fire suppression releasing applications in FlashScan systems. Power to the release agent solenoid(s) runs through the module for full-time monitoring and supervision. The FCM-1-REL(A) Releasing Control Module uses a redundant protocol; the module must be armed with a pair of signals in order to activate. It will then enter a 3-second window awaiting a pair of confirmation signals. If no confirmation is received, the module will automatically reset. It also supervises the wiring to the connected load and reports the status to the as NORMAL, OPEN, or SHORT CIRCUIT. The module has two pairs of output termination points available for fault-tolerant wiring and a controlled LED indicator. The module may be connected to either one 24VDC solenoid or up to two 12VDC solenoids that are listed with the IQ-318 and IQ-636X-2 s. To ensure proper operation, this module shall be connected to a compatible AUTOPULSE system control only (list available upon request). In addition, please refer to AUTOPULSE Device Compatibility Document, Part No. 50054, for the list of compatible solenoids. Note: FCM-1-REL(A) is required for all new FlashScanmode releasing applications with IQ-318 (version 12.0 or higher) and IQ-636X-2 (version 12.0 or higher) s. Use FCM-1 for releasing applications on IQ-636X, IQ-301, and IQ-396X s. Technical Information GENERAL Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . 15 to 32 VDC Communication Line Loop Impedance . . . . . . . 40 Ohm max. Temperature Range . . . . . . . . . 14°F to 140°F (–10° to 60°C) Relative Humidity . . . . . . . . . . . . 10% to 95% noncondensing Shipping Weight. . . . . . . . . . . . . . . . . . . . . . . . . 5.5 oz (156 g) Dimensions: High . . . . . . . . . . . . . . . . . . . . . 4.7 in. (119 mm) Wide . . . . . . . . . . . . . . . . . . . . 4.3 in. (109 mm) Deep . . . . . . . . . . . . . . . . . . . . . 1.4 in. (36 mm)

SLC Average Operating Current . . . . . . . . 700 μA max @ 24 VDC (one communication every 5 sec. with LED enabled) Maximum Activation Current. . . . . . . . . . . . . 9.0 mA (LED on) EXTERNAL SUPPLY Normal Operating Voltage . . . . . . . . . . . . . . 24 VDC Nominal Maximum Line Loss . . . . . . . . . 2.3 VDC (total allowable loss from power supply to module and from module to solenoid) Minimum Operating Voltage to Activate Solenoid . . . . . . . . . . . . . . . . 18 VDC (at solenoid) Standby Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 mA Activation Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA SOLENOID Supervisory Loop Voltage . . . . . . . . . . . . . . . . . . . . . . . . 3.3 V Supervisory Loop Current (Normal) . . . . . . . . . . . . . . . 30 mA Maximum Activation Current. . . . . . . . . . . . . . . . . . . . . . . . 2 A Listings and Approvals* These listings and approvals apply to the modules specified in this document. In some cases, certain modules or applications may not be listed by certain approval agencies, or listings may be in process. Consult factory for latest listing status. UL Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . (FCM-1-RELA) FM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approved CSFM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7300-0028:249 *Listings and Approvals are under NOTIFIER.

3-29.1

TYPICAL CLASS B, SOLENOID CONFIGURATION 24 VDC CIRCUIT. DO NOT LOOP WIRE ON TERMINALS 10 & 11. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS. 24 VDC POWER SUPPLY ISOLATED, REGULATED, POWER LIMITED PER NFPA 70. UL 864 LISTED FOR RELEASING DEVICE WITH BATTERY BACKUP.

CONNECT MODULES TO LISTED COMPATIBLE CONTROL S ONLY FROM OR PREVIOUS DEVICE

RELEASING CONTROL MODULE

SIGNAL LINE CIRCUIT (SLC) 32 VDC MAXIMUM. TWISTED PAIR IS RECOMMENDED.

POWER SUPPLY SUPERVISION BY MODULE

OUTPUT TO A UL LISTED FIRE ALARM RELEASING SOLENOID (REFER TO MANUFACTURER’S INSTALLATION DOCUMENT)

008863

TO NEXT DEVICE TO NEXT MODULE

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

Ordering Information Shipping Weight lb (kg) _________ 1 (0.5)

Part No. ______ 436861

Description _________ FCM-1-REL Releasing Control Module

436942

FCM-1-RELA Releasing Control Module (ULC Version)

1

(0.5)

436202

CB500 Control Module Barrier

0.5

(0.2)

FlashScan is a trademark of Honeywell International.




FRM-1 Relay Module (IQ-318/IQ-636X-2) Features • Built-in type identification automatically identifies these devices to the control unit • Internal circuitry and relay powered directly by two-wire SLC loop • Integral LED blinks green each time a communication is received from the control unit and turns on in steady red when activated • LED blink may be deselected globally (affects all devices) • High noise immunity (EMF/RFI) • Wide viewing angle of LED • SEMS screws with clamping plates for wiring ease • Face plate is made of off-white Noryl® • Controls include two rotary switches for direct-dial entry of address (01-159) • Two Form-C dry s that switch together • FlashScan® communication protocol Applications The FRM-1 Addressable Relay Module provides the AUTOPULSE IQ-318 or IQ-636X-2 with dry- outputs for activating a variety of auxiliary devices, such as fans, dampers, control equipment, etc. Addressability allows the dry to be activated, either manually or through programming, on a select basis. FlashScan (U.S. Patent 5,539,389) is a communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the unit U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of other designs. Description Each FRM-1 module uses one of 159 possible module addresses on a SLC loop. It responds to regular polls from the control unit and reports its type and status, including the open/normal/short status of its Notification Appliance Circuit (NAC). The LED blinks with each poll received. On command, it activates its internal relay. The FRM-1 can be used to replace the CMX-2 module (Part No. 417479) in existing systems.

Technical Information Normal Operating Voltage: . . . . . . . . . . . . . . . . 15 to 32 VDC Maximum Current Draw:. . . . . . . . . . . . . . . . 6.5 mA (LED on) Average Operating Current:. . . . . . . . . 300 μA (LED flashing) EOL Resistance: . . . . . . . . . . . . . . . . . . . . . . . . . . . . not used Temperature Range:. . . . . . . . 32 °F to 120 °F (0 °C to 49 °C) Humidity Range: . . . . . . . . . . . . 10% to 93% non-condensing RELAY RATINGS Load Description Resistive Resistive Resistive Resistive Inductive (L/R = 5 ms) Inductive (L/R = 2 ms) Inductive (PF = 0.35 ) Inductive (PF = 0.35) Inductive (PF = 0.35) Inductive (PF = 0.35)

Application Non-Coded Coded Non-Coded Non-Coded Coded Coded Non-Coded Non-Coded Non-Coded Non-Coded !

Current Rating 3.0 A 2.0 A 0.9 A 0.9 A 0.5 A 1.0 A 0.3 A 1.5 A 0.7 A 2.0 A

WARNING

All relay switch s are shipped in the standby (open) state, but may have transferred to the activated (closed) state during shipping. The presence of high voltage may cause serious injury or death. To ensure that the switch s are in their correct state, modules must be made to communicate with the before connecting circuits controlled by the module. MOUNTING THE FRM-1 TO A 4 INCH SQUARE, 2 1/8 INCH DEEP JUNCTION BOX

Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in TYPE CODE (not settable) will identify the module to the control unit, so as to differentiate between a module and a sensor address. The FRM-1 may be programmed to operate dry s for door holders, Air Handling Unit shutdown, etc., and to re-set four-wire smoke detector power.

Maximum Voltage 30 VDC 30 VDC 110 VDC 125 VAC 30 VDC 30 VDC 125 VAC 25 VAC 70.7 VAC 25 VAC

ISOLATED QUADRANT

004752

3-30

Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS669 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM). . . . . . . 7300-0028:202 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457-99-E Maryland State Fire Marshal. . . . . . . . . . . . . . . Permit # 2020 USCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1

Ordering Information

Shipping Weight lb (kg)

Part No.

Description

428102

FRM-1 Intelligent Relay Module

1

(0.45)

437067

FRM-1A Intelligent Relay Module (ULC)

1

(0.45)

436202

CB500 Barrier

0.5

(0.23)

* Listings and Approvals are under NOTIFIER.

WIRING DIAGRAM

SIGNAL LINE CIRCUIT (SLC) 32 VDC MAXIMUM. TWISTED PAIR RECOMMENDED

TO NEXT DEVICE

FROM OR PREVIOUS DEVICE CONTROL MODULE

RELAY COMMON NORMALLY CLOSED NORMALLY OPEN RELAY COMMON NORMALLY CLOSED

IF ANY WIRING TO TERMINALS 4-10 IS NONPOWER LIMITED, THE CB500 BARRIER IS REQUIRED. THE CB500 INCLUDES A NONPOWER LIMITED LABEL, WHICH MUST BE PLACED OVER THE POWER LIMITED TERMINAL INFORMATION ON THE NAMEPLATE LABEL.

MODULE DOES NOT SUPERVISE CONTROLLED CIRCUITS UNUSED NORMALLY OPEN 1 *NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE. 008212

RELAY CONTROL MODULE USED TO DISCONNECT A POWER SUPPLY FROM OR PREVIOUS DEVICE

TO NEXT DEVICE

DC POWER SUPPLY LISTED FOR FIRE PROTECTION WITH BATTERY BACK-UP

COMMUNICATION LINE – 32 VDC MAXIMUM. TWISTED-PAIR IS RECOMMENDED

004751b

FlashScan is a trademark of Honeywell International. Noryl is a ed trademark of GE Plastics, a subsidiary of General Electric Company.




ISO-X Fault Isolator Module (IQ-318/IQ-636X-2) Features • Powered by Signaling Line Circuit (SLC) loop directly, no external power required • Meets NFPA 72 Style 7 requirements • Mount in standard 4 inch (102 mm) square junction box, minimum 2 1/8 inch (54 mm) deep • Integral LED blinks to indicate normal condition; illuminates steady when short circuit condition is detected • High noise (EMI/RFI) immunity • Wide viewing angle of LED • SEMS screws with clamping plates for ease of wiring • Opens SLC loop automatically on detection of short, preventing the short from causing failure of the entire loop • Automatically resets on correction of short Applications The Fault Isolator Modules should be spaced between groups of sensors in a loop to protect the rest of the loop. It is used to isolate short circuit problems within a section of a loop so that other sections can continue to operate normally. Description The ISO-X Fault Isolator Module is used with the AUTOPULSE IQ-318 and IQ-636X-2 control system to isolate short circuits on the SLC loop, so that unshorted sections of the loop can continue to operate normally. In Style 4 loops, the ISO-X is generally used at each T-tap branch to limit the effect of short circuits on a branch to the devices on that branch. The module automatically opens a circuit when the line voltage drops below 4 volts. Fault Isolator Modules should be spaced between groups of sensors in a loop to protect the rest of the loop. If a short should occur between any two isolators, then both isolators immediately switch to an open circuit state and isolate the group of sensors between them. The remaining units on the loop continue to operate normally. The ISO-X Fault Isolator Module automatically restores the shorted portion of the communications loop to normal condition when the short circuit condition is removed. It mounts on a standard 4 in. (102 mm) mounting junction box which is at least 2 1/8 in. (54 mm) deep. Installation instructions are provided with each module and terminal screws are provided for “in and out” wiring. The Fault Isolator Module (ISO-X) is used to protect critical elements of the communications loop from faults on other branches or sections of the loop. The ISO-X continuously monitors the circuit connected to terminals 3 (–) and 4 (+). Upon power-up, an integral relay is latched on.

008864

The ISO-X periodically pulses the coil of this relay. A short circuit on the loop resets the relay. The ISO-X sees this short and disconnects the faulted branch by opening the positive side of the loop (terminal 4). This effectively isolates the faulted branch from the remainder of the loop. The LED indicator is on continuously during a short circuit condition. Once the fault is removed, the ISO-X automatically reapplies power to the communications loop branch. Note: During a fault condition, the AUTOPULSE IQ-318 and IQ-636X-2 control system will a trouble condition for each zone mapped to the isolated loop branch. The face plate is made of LEXAN® with off-white color. It includes a yellow LED indicator that pulses when normal and turns on solid when a short is detected.

Technical Information Operating Voltage:. . . . . . . . . . . . . . . . . . 15 – 28 VDC (peak) Current Range: . . . . . . . . . . . . 5 mA for LED latched in alarm Standby Current:. 400 μA maximum, plus supervision current Temperature Range: . . . . +32 °F to +120 °F (0 °C to +49 °C) Relative Humidity: . . . . . . . . . . . . . . . . . . . . . . . . 10% to 95% Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 oz (150 g) MOUNTING THE ISO-X ISOLATOR MODULE TO A 4 INCH SQUARE, 2 1/8 INCH DEEP, JUNCTION BOX

007348

3-31

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . CS118, CS733 (ISO-XA) Factory Mutual (FM). . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7165-0028:243; 7170-0028:244 USCG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 MEA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128-07-E * Listings and Approvals are under NOTIFIER


Part No.

Description


417480

ISO-X Fault Isolator Module

2

(0.9)

437069

ISO-XA Fault Isolator Module (ULC)

2

(0.9)

LEXAN is a ed trademark of General Electric Corporation.



Detection and Control Components ACS Series Annunciator Modules (IQ-318/IQ-636X-2) Features • Speaker control mode for use with the AUTOPULSE IQ-318 and IQ-636X-2 s; enables the ACS to control operation of groups of multi-channels mapped to groups of multi-speakers • Compatible with existing annunciators • Color-programmable LEDs • On-board end-of-line resistors can be enabled/disabled by setting a switch • Alarm/Circuit On and Trouble LED per point option or more dense Alarm-only option • Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate • LEDs may be programmed to display status of indicating circuits or control relays as well as system status conditions • System Trouble LED indicator • On-Line/Power LED indicator • Alarm and trouble resound with flash of new conditions • Local sounder for both alarm and trouble conditions with silence/acknowledge button (program options) • May be powered by 24 VDC from the or by remote power supplies • Microprocessor-controlled electronics, fully supervised • Slip-in custom labels, lettered with standard typewriter or LabelEase program • Plug-in terminal blocks for ease of installation and service. Applications The ACS Series Annunciators provide a modular line of products for annunciation and control of the AUTOPULSE IQ-318 and IQ-636X-2 control s, the NCA-2, and legacy addressable s. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. These ACS units use a serial interface and maybe located at distances of up to 6,000 ft (1,828.8 m) from the .

008916

Construction The ACS modules are provided in two basic controller modules, each with its expander module. The ACM-24AT provides 24 annunciation and control points per module, each with a red, green, or yellow Alarm/Circuit On LED, a yellow Trouble LED, and a touch-key switch. The ACM-48A provides 48 annunciation points per module, each with a red, green, or yellow Alarm/Circuit On LED (for annunciating control relays, the LED indicates ON/OFF). On the ACM-24AT, each LED point is individually color-programmable. On ACM-48A, each column of 24 LED points can be color-configured using a DIP switch. Temperature and humidity ranges: This system meets NFPA requirements for operation at 32 °F to 120 °F (0 °C to 49 °C), and at a relative humidity (non-condensing) of 85% at 86 °F (30 °C) per NFPA, and 93% ± 2% at 90 °F ± 1 °F (32 °C ± 2 °C) per ULC. However, the useful life of the system’s standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and all peripherals be installed in an environment with a nominal room temperature of 60 °F to 80 °F (15 °C to 27 °C).

3-32

Installation The ACS Series annunciator and control subsystems use modular hardware assemblies which allow the custom configuration of the annunciator to fit the individual job requirements. Standard back boxes and mounting hardware schemes, including special remote cabinets, allow the annunciators to be constructed and configured with other system components. When used with the AUTOPULSE IQ-318, IQ-636X-2, or legacy s, the ACS modules can be used for manual selection of speaker and telephone circuits. In this application, they are typically mounted in the main control near the microphone and telephone handset. For remote annunciation applications, the modules are typically mounted in special ABF or ABS boxes. Control switch key locks (AKS-1B) are available. Communication between the ACS Series annunciators and the host Fire Alarm Control is made through an EIA485 multi-drop loop, eliminating the need for costly wiring schemes. Four wires are required, two for the EIA-485 communications (twisted pair), and two for 24 VDC regulated power. Retrofit of ACS Series annunciators into existing systems is easily accomplished. Software may require upgrading, and some legacy s may require an interface board. All field-wiring terminations use removable, compressiontype terminal blocks for ease of installation, wiring, and circuit testing. Operation The ACS Series annunciator and control system provides the AUTOPULSE system with up to 32 remote serially connected annunciators, each with a capacity of 96 points, for a total capacity of 3072 points (subject to the capability of the FA).The NFS2-3030 and NCA-2 are capable of using the full 96points. Local or remote power supplies and serial communications allow the ACS to be located virtually anywhere on the protected premises. On AUTOPULSE IQ-318, IQ-636X-2 and the legacy s, system alarm and/or trouble conditions may be annunciated on a per-point basis, or in a grouped or zone configuration. Control of system operational controls, such as Signal Silence, System Reset, and local annunciation controls (such as Local Acknowledge and Lamp Test) may be accomplished through the module’s rubber keypad.

Agency Listings and Approvals* The listings and approvals below apply to the ACM/AEM24AT and the ACM/AEM-48A. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL . . . . . . . . . . . . . . . . . . . . . . . . . . S635 • ULC . . . . . . . . . . . . . . . . . . . . . . . . . S635 • FDNY . . . . . . . . . . . . . . COA #6067 (NFS2-640), COA #6065 (NFS2-3030) • CSFM . . . . . . . . . 7120-0028:0156, 7165-0028:0243, 7165-0028:0224 • FM . . . . . . . . . . . . . . . . . . . . . . . . Approved *Listings and Approvals are under NOTIFIER.

Ordering Information ACM-24AT: The Annunciator Control Module-24AT contains 24 color-programmable (red/green/yellow) Active and 24 yellow Trouble LEDs, 24 momentary touch-pad switches, a System Trouble LED, an On-Line/Power LED, and a local piezo sounder with a silence/acknowledge switch for audible indication of alarm and trouble conditions. Includes instructions. The ACM-24AT is 8.375 in. (213 mm) high x 4.375 in. (111 mm) wide. AEM-24AT: The Annunciator Expander Module-24AT expands the ACM-24AT by 24 system points. The AEM24AT is identical in size and in frontal appearance to the ACM-24AT. Up to three of these expander modules can be ed by an ACM-24AT, for a maximum of 96 system points. The AEM-24AT is 8.375 in. (213 mm) high x 4.375 in. (111 mm) wide. Note: The AEM-24AT cannot be used to expand the ACM48A. ACM-48A: The Annunciator Control Module-48A contains 48 color-programmable (red/green/yellow) Active LEDs, a System Trouble LED, an On-Line/Power LED, and a local piezo sounder with a Silence/Acknowledge switch for audible indication of alarm and trouble conditions. Includes instructions. The ACM-48A is 8.375 in. (213 mm) high x 4.375 in. (111 mm) wide. AEM-48A: The Annunciator Expander Module-48A expands the ACM-48A by 48 system points. The AEM-48A is identical in frontal appearance to the ACM-48A. One expander module can be ed by an ACM-48A, providing a maximum of 96 points (subject to the capability of the FA). The AEM-48A is 8.375 in. (213 mm) high x 4.375 in. (111 mm) wide. Note: The AEM-48A cannot be used to expand the ACM24AT. ABS-1TB: The ABS-1TB is an attractive black surfacemount back box for mounting one ACS Series Annunciator. Unlike the ABS-1B, the ABS-1TB has an increased depth that allows mounting of the AKS-1B Annunciator Key Switch. The ABS-1TB is 9.938 in. (252 mm) high x 4.625 in. (117 mm) wide x 2.5 in. (64 mm) deep. Note: An earlier gray model ABS-1TB will not accommodate the ACM/AEM-24AT or ACM/AEM-48A. The slightly deeper ABS-1TB will accommodate both the ACM/AEM-24AT or ACM/AEM-48A models.

Ordering Information (Continued) ABF-1B: The Annunciator Flush Box-1B (black) provides for the remote mounting of a single annunciator module in a flush-mount enclosure. Knockouts are provided for use with 1/2 in. (13 mm) conduit. The ABF-1B includes a painted black metal trim plate (11 in. (279 mm) high x 6.25 in. (159 mm) wide), mounting hardware, and an adhesivebacked annunciator label for the dress plate. The ABF-1B is 9.938 in. (252 mm) high x 4.625 in. (117 mm) wide x 2.5 in. (64 mm) deep.


Part No.

Description

432787

ACM-24AT, Annunciator Control Module, 24 Zone Alarm/Trouble

2

(0.9)

432790

AEM-24AT, Annunciator Expander Module, 24 Zone Alarm

2

(0.9)

432788

ACM-48A, Annunciator Control Module, 48 Zone Alarm/Trouble

2

(0.9)

432791

AEM-48A, Annunciator Expander Module, 48 Zone Alarm

2

(0.9)

417493

ABS-1TB, Annunciator Back Box, Surface, Single, Deep

1

(0.5)

417657

ABF-1B, Annunciator Back Box, Flush, Single

1

(0.5)

433520

ADP-4B, Annunciator Dress

2

(0.9)

433614

DP-DISP2, Dress

2

(0.9)

432794

BMP-1, Annunciator Blank Module

2

(0.9)

417660

AKS-1B, Annunciator Key Switch

1

(0.5)

008917

ADP-4B: The Annunciator Dress -4B (black) provides for the cabinet mounting of one to four modules. The ADP-4B hinge-mounts to the CAB-4 Series cabinet. Modules mount directly to threaded studs on the dress . DP-DISP2: Dress accommodates up to two annunciator modules (no expanders). BMP-1: Annunciator Blank Module is a flat black dress plate that covers unused module positions in the annunciator back box or in the ADP-4B. The BMP-1 is 8.375 in. (213 mm) high x 4.375 in. (111 mm) wide. Studs for a variety of module mounting options are available. AKS-1B: The Annunciator Key Switch-1B (black) provides access security for the control switches on the ACM/AEM24AT. The key switch kit includes a key and hardware for mounting to the ABF-1B. Also included is an adhesivebacked annunciator label for use with the key switch/dress plate assembly. Note: The AKS-1B can only be employed with the ABS-1TB.




ACM-8R Relay Module (IQ-318/IQ-636X-2) Features • Provides eight Form-C relays with 5-amp s • The relays can be employed to track any group of 8 software zones in the AUTOPULSE IQ-301 control system or track a variety of devices and points, in a group fashion, on the IQ-318 or IQ-636X-2 • Removable terminal blocks for ease of installation and service • DIP switch selectable memory mapping of relays • Compatible with AUTOPULSE IQ-318 and IQ-636X-2 control units Applications The ACM-8R is a module in the ACS class of annunciators and will mount to an ABS-8RB annunciator surface-mount back box with blank faceplate. It provides the AUTOPULSE IQ-318 or IQ-636X-2 control system with a mappable relay control module. The relays on this module can be selected for mapping anywhere in the AUTOPULSE IQ-318 or IQ-636X-2 (by groups of eight) control system memory map. Description Communication between the control unit and the ACM-8R is accomplished over a two-wire EIA-485 serial interface. This communication, to include the wiring, is supervised by the AUTOPULSE control system. Power for the annunciators is provided via a separate power loop from the control unit which is inherently supervised (loss of power also results in a communication failure at the control unit). Up to 32 annunciators may be installed on an EIA-485 circuit.

RELAY TERMINAL ASSIGNMENTS THE ACM-8R PROVIDES EIGHT RELAYS WITH FORM-C S RATED FOR 5 AMPS. THE TERMINAL ASSIGNMENTS ARE ILLUSTRATED BELOW.

RELAY 4

RELAY 3

RELAY 2

RELAY 1

{ { { {

NORMALLY OPEN COMMON NORMALLY CLOSED NORMALLY OPEN COMMON NORMALLY CLOSED NORMALLY OPEN COMMON NORMALLY CLOSED NORMALLY OPEN COMMON NORMALLY CLOSED

{ { { {

RELAY 5

RELAY 6

RELAY 7

RELAY 8

CIRCUITS CAN BE ANNUNCIATED AS ALARM, OR ALARM AND TROUBLE. ALARM AND TROUBLE CONSUMES TWO ANNUNCIATOR POINTS.

007253

THE ACM-8R RELAY MODULE

ABS-8RB BACK BOX: 9 15/16 IN. x 4 5/8 IN. x 2 1/2 IN. DEEP (252 mm x 117 mm x 64 mm DEEP)

007254

007252

3-33

Technical Information Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 VDC Standby Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Maximum Current (all relays activated): . . . . . . . . . . . 158 mA Data Communications Port:. . . . . . . . . . . . . . . . . . . . EIA-485 operating at 20 K baud Relay Rating Resistive:. . . . . . . . . . . . . . 5 amps @ 125 VAC or 30 VDC Inductive: . . . . . . . . . . . . . . . . . . . . . . . 2 amps @ 125 VAC Note: Form-C gold-plated, silver alloy relay s are for medium duty switching and are not intended for motor control or pilot duty. Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS635 Vol. 1 MEA (NYC). . . . . . . . . . . . . . . . . . . . . . . . . . 128-07-E Vol. 5** Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM). . . . . . 7120-0028: 156 *Listings and Approvals are under NOTIFIER. **Listing under Tyco Fire Protection Products.


Part No. Description


417653

2

(0.9)

1

(0.5)

436996

ACM-8R, Annunciator Control Module with 8 Relays ABS-8RB, Surface Back Box



Detection and Control Components XP10-M Ten-Input Monitor Module (IQ-318/IQ-636X-2) Features • Ten addressable Class B or five addressable Class A initiating device circuits • Removable 12 AWG (3.25 mm2) to 18 AWG (0.9 mm2) plug-in terminal blocks • Status indicators for each point • -Controlled Green LED Indicators • Unused addresses may be disabled • Rotary address switches • Class A or Class B operation • FlashScan® or CLIP operation • Mount one or two modules in a BB-XP cabinet (optional) • Mount up to six modules on a CHS-6 chassis in a CAB-3 Series or BB-25 cabinet (optional) • Mounting hardware included 007000

Description The XP10-M ten-input monitor module provides an interface between the addressable AUTOPULSE IQ-318 and IQ-636X-2 control units and normally open devices, such as pull stations, heat detectors, or flow switches. The first address on the XP10-M is set from 01 to 150 and the remaining modules are automatically assigned to the next nine higher addresses. Provisions are included for disabling a maximum of two unused addresses. The supervised state (normal, open, or short) of the monitored device is sent back to the . A common SLC input is used for all modules, and the initiating device loops share a common supervisory supply and ground – otherwise each monitor operates independently from the others. Each XP10-M module has -controlled green LED indicators. FlashScan (U.S. Patent 5,539,389) is a communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the unit’s U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of earlier designs.

Technical Information Standby Current:

3.5 mA (SLC current draw with all addresses used; if some addresses are disabled, the standby current decreases.)

Alarm Current:

55 mA (assumes all ten LEDs solid ON)

Temperature Range:

32 °F to 120 °F (0 °C to 49 °C) for UL applications; 14 °F to 131 °F (–10 °C to 55 °C) for EN54 applications

Humidity Range:

10% to 85% noncondensing for UL applications; 10% to 93% noncondensing for EN54 applications

Dimensions: Height:

6.8 in. (172.7 mm)

Width:

5.8 in. (147.3 mm)

Depth:

1.25 in. (31.75 mm)

Wire Gauge:

12 AWG (3.25 mm2) to 18 AWG (0.9 mm2)

Maximum SLC Wiring Resistance:

40 or 50 ohms, dependent

Maximum IDC Wiring Resistance:

40 ohms

Maximum IDC Voltage: 12 VDC Maximum IDC Current: 1 mA

3-34

Installation Power-limited circuits must employ type FPL, FPLR, or FPLP cable as required by Article 760 of the NEC. The XP10-M is shipped in Class B position. Remove shunt for Class A operation. Up to six XP10-M modules can be mounted on a CHS-6 chassis, which mounts in a BB-25, CAB 3 or 4, or suitably grounded metallic cabinet. One or two modules can be mounted in a BB-XP cabinet. Mounting hardware and installation instructions are provided with each module.

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 Factory Mutual (FM). . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7300-0028:219 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-02-E Maryland State Fire Marshal . . . . . . . . . . . . . . . Permit #2106 USCG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 * Listings and Approvals are under NOTIFIER.

Wiring Each XP10-M module comes with removable 12 AWG (3.25 mm2) to 18 AWG (0.9 mm2) plug-in terminal blocks.


Typical Initiating Device Circuit Configuration – Class B, Style B. Note: Any number of UL-Listed closure devices may be used. DO NOT MIX fire alarm initiating and supervisory devices on the same initiating device circuit. Install closure devices per manufacturer’s installation instructions.

428078

Part No. ______ 432714

428079 428080

Description _________ XP10-M Ten-input Monitor Module (UL) BB-XP Cabinet for One or Two Modules BB-25 Cabinet CHS-6 Chassis

Shipping Weight lb (kg) ___________ 1.1 (0.5) 7

(3.2)

15 2

(6.8) (0.9)

CHS-6 CHASSIS

004754

007001

Typical Fault-Tolerant Initiating Device Circuit Configuration – Class A, Style D. Note: Any number of UL-Listed closure devices may be used. DO NOT MIX fire alarm initiating and supervisory devices on the same initiating device circuit. Install closure devices per manufacturer’s installation instructions.

19 IN. WIDE X 7 5/16 IN. HIGH X 2 3/16 IN. DEEP (483 mm wide x 186 mm high x 56 mm deep) BACK-BOX/CABINET C

B

A

004755

Dimensions

007002

A – Width

B – Height

C – Depth

BB-25 Battery Back Box

24 in (610 mm)

12 5/8 in (321 mm)

5 1/4 in (133 mm)

BB-XP Cabinet

9 1/2 in (241 mm)

12 1/2 in (318 mm)

3 in (76 mm)

FlashScan is a ed trademark of Honeywell International.




(Page Left Intentionally Blank)

3-35 TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411

Copyright © 2011 Tyco Fire Protection Products All rights reserved.

Detection and Control Components XP6-R Six-Relay Control Module (IQ-318/IQ-636X-2) Features • Six addressable Form-C relay s • Removable 12 AWG (3.25 mm2) to 18 AWG (0.9 mm2) plug-in terminal blocks • Status indicators for each point • -Controlled Green LED Indicators • Unused addresses may be disabled • Rotary address switches • FlashScan® or CLIP operation • Mount one or two modules in a BB-XP cabinet (optional) • Mount up to six modules on a CHS-6 chassis in a CAB-3 Series or BB-25 cabinet (optional) • Mounting hardware included Description The XP6-R six-relay control module provides the addressable AUTOPULSE IQ-318 and IQ-636X-2 control units with six Form-C relays. The first module is addressed from 01 to 154 while the remaining modules are automatically assigned to the next five higher addresses. Provisions are included for disabling a maximum of three unused modules. A single isolated set of dry relay s is provided for each module address, which is capable of being wired for either a normally-open or normally-closed operation. The module allows the control to switch these s on command. No supervision is provided for the controlled circuit. Each XP6-R module has -controlled green LED indicators. FlashScan® (U.S. Patent 5,539,389) is a communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the unit’s U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of earlier designs.

007003

Technical Information Standby Current:

1.45 mA (SLC current draw with all addresses used; if some addresses are disabled, the standby current decreases.)

Alarm Current:

32 mA (assumes all six relays have been switched once and all six LEDs solid ON)

Temperature Range:

32 °F to 120 °F (0 °C to 49 °C)

Humidity Range:

10% to 85% noncondensing

Dimensions: Height: Width: Depth:

6.8 in. (172.7 mm) 5.8 in. (147.3 mm) 1.0 in. (25.4 mm)

Wire Gauge:

12 AWG (3.25 mm2) to 18 AWG (0.9 mm2)

Maximum SLC Wiring Resistance: Relay Current:

40 or 50 ohms, dependent 30 mA/relay pulse (15.6 ms pulse duration), pulse under control

Relay Ratings: 30 VDC; 125 VAC Current Ratings: 3.0 A @ 30 VDC maximum, resistive, non-coded 2.0 A @ 30 VDC maximum, resistive, coded 1.0 A @ 30 VDC maximum, inductive (L/R=2 ms), coded 0.5 A @ 30 VDC maximum, inductive (L/R=5 ms), coded 0.9 A @ 110 VDC maximum, resistive, non-coded 0.9 A @ 125 VAC maximum, resistive, non-coded 0.7 A @ 70.7 VAC maximum, inductive (PF=0.35), non-coded 0.5 A @ 125 VAC maximum, inductive (PF=0.35), non-coded 3-36

CHS-6 CHASSIS

Installation Up to six XP6-R modules can be mounted on a CHS-6 chassis, which mounts in a BB-25, CAB-A3, CAB 3 or 4 series cabinet. One or two modules can be mounted in BB-XP cabinet. Mounting hardware and installation instructions are provided with each module. Wiring Each XP6-R module comes with removable 12 AWG (3.25 mm2) to 18 AWG (0.9 mm2) plug-in terminal blocks.

004754

19 IN. WIDE X 7 5/16 IN. HIGH X 2 3/16 IN. DEEP (483 mm wide x 186 mm high x 56 mm deep) BACK-BOX/CABINET

C

007004

B

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . CS118 (XP6-RA) Factory Mutual (FM) . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . 7300-0028:219 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . 368-01-E Maryland State Fire Marshal. . . . . . . . . . Permit #2099 USCG. . . . . . . . . . . . . . . . . . . . . 161.002/A42/1

A

*Listings and Approvals are under NOTIFIER. 004755

Ordering Information Part No. ______ 432716 428078 428079 428080

Description _________ XP6-R Six-relay Control Module (UL) BB-XP Cabinet for One or Two Modules BB-25 Cabinet CHS-6 Chassis

Shipping Weight lb (kg) __________ 1.1 (0.5)

Dimensions A – Width

B – Height

C – Depth

7

(3.2)

BB-25 Battery Back Box

24 in (610 mm)

12 5/8 in (321 mm)

5 1/4 in (133 mm)

15 2

(6.8) (0.9)

BB-XP Cabinet

9 1/2 in (241 mm)

12 1/2 in (318 mm)

3 in (76 mm)




Detection and Control Components FDM-1 Addressable Dual Monitor Module (IQ-318/IQ-636X-2) Features • Built-in type identification automatically identifies this device as a monitor module to the AUTOPULSE control unit • Powered directly by two-wire SLC loop, no additional power required • High noise (EMF/RFI) immunity • SEMS screws with clamping plates for ease of wiring • Direct-dial entry of address (01-159) • LED flashes green during normal operation (this is a programmable option), and latches on steady RED to indicate alarm • FlashScan® communication protocol

FlashScan (U.S. Patent 5,539,389) is a communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the unit’s U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of earlier designs. The FDM-1 automatically assigns itself to two addressable points, starting with the original address. For example, if the FDM-1 is set to address “56,” then it will automatically assign itself to addresses “56” and “57.” Note: “ones” addresses on the FDM-1 are 0, 2, 4, 6, or 8 only. Terminals 6 and 7 use the first address, and terminals 8 and 9 use the second address.

• Compatible with IQ-318 and IQ-636X-2 Applications Use the FDM-1 module to monitor two zones of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry- alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the control unit. Monitored circuit may be wired as an NFPA Style B only. A 47K ohm End-of-Line Resistor (provided) terminates the Style B circuit. The FDM-1 does not Style D (Class A) initiating device circuits. Maximum IDC loop resistance is 1500 ohms. Description The FDM-1 is a standard-sized dual monitor module used to monitor and supervise two independent two-wire initiating device circuits (IDCs) at two separate, consecutive addresses in intelligent, two-wire systems. Each FDM-1 uses two consecutive addresses of the 159* available module addresses on an SLC loop. It responds to regular polls from the control unit and reports its type and the status (open/normal/short) of its IDC. A green flashing LED indicates that the module is in communication with the control unit. The LED latches on steady red to indicate alarm (subject to current limitations on the loop).

NOTICE Avoid duplicating addresses on the system.

Technical Information Nominal Operating Voltage: . . . . . . . . . . . . . . . 15 to 32 VDC Maximum Current Draw: . . . . . . . . . . . . . . . 5.7 mA (LED on) Maximum IDC Resistance: . . . . . . . . . . . . . . . . . . 1500 ohms Average Operating Current: . . . . . . . . 750 μA (LED flashing) EOL Resistance: . . . . . . . . . . . . . . . . . . . . . . . . . . . 47K ohms Temperature Range: . . . . . . 32 °F to 120 °F ( 0 °C to 49 °C) Humidity Range: . . . . . . . . . . . . 10% to 93% non-condensing Dimensions: Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 in. (114 mm) Width:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 in. (102 mm) Depth: . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.125 in. (54 mm) Installation The FDM-1 module mounts directly to a standard 4 in. square, 2.124 in. (54 mm) deep, electrical box. Mounting hardware and installation instructions are provided with each module. All wiring must conform to applicable local codes, ordinances, and regulations. These modules are intended for power-limited wiring only.

3-37

MOUNTING THE FDM-1 TO A 4 IN. (102 mm) SQUARE 2 1/8 IN. (54 mm) DEEP JUNCTION BOX

Wiring • Connect modules to listed compatible AUTOPULSE control units only. • All wiring shown is supervised and power limited. • Install closure devices per manufacturers’ installation instructions. • Any number of UL-listed closure devices may be used. • DO NOT MIX fire alarm initiating, supervisory, or security devices on the same circuit. Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS669 Factory Mutual (FM). . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7300-0028:202 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143-01-E USCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 * Listings and Approvals are under NOTIFIER.


Shipping Weight lb (kg) 1 (0.45)

004745

Part No. 432294

DETAIL OF FDM-1 – NOTE “ONES” ADDRESSES ARE 0, 2, 4, 6, 8 ONLY

Description FDM-1 Monitor Module

006882

TYPICAL DUAL TWO-WIRE STYLE B INITIATING DEVICE CIRCUIT CONFIGURATION TWO INITIATING DEVICE CIRCUITS (L & H) EACH POWER-LIMITED TO 230 μ MAX. @ 12 VDC MAX.

TO NEXT DEVICE

FROM OR PREVIOUS DEVICE COMMUNICATION LINE – 32 VDC MAXIMUM. SHIELDED/TWISTED-PAIR IS RECOMMENDED

47K EOL RESISTOR ELR-47K

• ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED.

47K EOL RESISTOR ELR-47K

• CONNECT MODULES TO LISTED COMPATIBLE CONTROL S ONLY. 006883

FlashScan is a ed trademark of Honeywell International. TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411



Applications Use the FMM-101 module to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry- devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the AUTOPULSE IQ-318 or IQ-636X-2 control unit. Monitored circuit/device is wired as an NFPA Style B (Class B) Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided) terminates the circuit. The FMM-101 monitor module can be installed in a singlegang junction directly behind the monitored unit. Its small size and lightweight allow it to be installed without rigid mounting. The FMM-101 is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary switches. It provides a two-wire initiating device circuit for normally-open- fire alarm and security devices. Description The FMM-101 is a miniature monitor module used to supervise a Class B (Style B) circuit. Its compact design allows the FMM-101 to often be mounted in a single-gang box behind the device it is monitoring. The FMM-101 can be used to replace MMX-101 module (Part No. 417478) in existing systems. Each FMM-101 uses one of 159 available module addresses on an SLC loop. It responds to regular polls from the control and reports its type and the status (open/normal/short) of its Initiating Device Circuit (IDC). FlashScan (patent pending) is a new communication protocol that greatly enhances the speed of communication between anatelligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new information, the unit’s U stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of earlier designs. FlashScan is a trademark of NOTIFIER.

BLACK

RED

YELLOW

Features • Built-in type identification automatically identifies this device as a monitor module to the AUTOPULSE control unit • Powered directly by two-wire FA, no additional power required • High noise (EMF/RFI) immunity • Tinned, stripped leads for ease of wiring • Direct-dial entry of address (01-159) • FlashScan™ communication protocol

VIOLET

FMM-101 Monitor Module (IQ-318/IQ-636X-2)

004757 Technical Information Nominal Operating Voltage:. . . . . . . . . . . . . . . . 15 to 32 VDC Average Operating Current:. . . . . . . . . . . 350 μA (maximum) EOL Resistance: . . . . . . . . . . . . . . . . . . . . . . . . . . . 47K ohms Temperature Range:. . . . . . . . 32 °F to 120 °F (0 °C to 49 °C) Humidity Range: . . . . . . . . . . . . 10% to 93% non-condensing Wiring Length:. . . . . . . . . . . . . . . . . . 6 in. (152 mm) minimum Dimensions: High: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 in. (33 mm) Wide: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.75 in. (70 mm) Deep:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 in. (13 mm)

Installation The FMM-101 module should be wired and mounted without rigid connections inside a standard electrical box. All wiring must conform to applicable local codes, ordinances, and regulations. Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS699 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . 7300-0028:202 MEA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128-07-E Maryland State Fire Marshal . . . . . . . . . . . . . . Permit #2020 USCG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 * Listings and Approvals are under NOTIFIER



Part No.

Description

428098 437065

FMM-101 Monitor Module FMM-101A Monitor Module (ULC)

1 1

(0.45) (0.45) 3-38



Detection and Control Components LDM Series Lamp Driver Modules (IQ-318/IQ-636X-2) Features • ALARM and TROUBLE Lamp/LED per point (IQ-318 and IQ-636X-2) or per software zone, or more dense ALARMonly option (field selectable) • System trouble Lamp/LED signal • On-line/power LED indicator • Alarm and trouble resound with flash of new conditions • Local sounder for both alarm and trouble conditions with silence/acknowledge switch connection • Serial EIA-485 interface for reduced installation cost • May be powered by 24 VDC from the unit or by remote power supplies • Efficient switched power converter reduces power consumption • Fully supervised microprocessor-controlled electronics • Plug-in terminal blocks for ease of installation and service • Trouble monitor option for remote power supplies Applications The LDM series lamp driver modules, when combined with a custom graphic display, provide annunciation and control for the AUTOPULSE IQ-318 or IQ-636X-2 control system. These modules use a serial communications interface and may be located up to 6,000 ft (1829 m) from the unit. The LDM-32/LDM-E32 with a custom graphic array may be used to indicate point or software zone status. In addition, the LDM-R32 module which connects to any LDM-32 or LDM-E32 converts transistor outputs to 32 Form-A dry s for electrical isolation when interfacing the system to other equipment. Description Two basic models are available: the LDM-32 control module and the LDM-E32 expander module. Each may be selected to provide 32 alarm indications or 16 alarm and 16 trouble. Both modules mount on four standoffs inside the custom annunciator graphic box. Alternately, the modules may be installed in a CHS-4L chassis. The CHS-4L chassis may be mounted to the graphic annunciator cabinet to provide installation of up to four LDM-32 or LDM-E32 modules. The LDM-32 includes a system trouble lamp driver and lamp test/local acknowledge switch input. Integral piezo sounder sounds for each new alarm or trouble and is silenced with the Local Acknowledge switch, or permanently disabled with a dip-switch selection. Flash of new alarms or trouble is selectable through dip switches. Switch inputs may be used for Silence or Reset. Instructions are included. One LDM-E32 is allowed per LDM-32 in alarm-only mode. Three LDM-E32 modules are allowed per LDM-32 in alarm/trouble mode. The LDM-E32 includes expander ribbon cable.

The LDM-R32 provides 32 Form-A dry s (1 amp @ 30 VDC) output terminal screw connections. It is mounted on an LDM-32 or an LDM-E32. A separate common is provided for each group of 8 relays. Ribbon cables to connect to the LDM-32/LDM-E32 are included. The LDM-CBL24 and LDM-CBL48 ribbon cable sets can be ordered to provide either a 24 in. (610 mm) or 48 in. (1219 mm) connection between LDM-32/LDM-E32 and LEDs or lamps on a custom graphic unit. They each include all cables necessary for one LDM-32 or LDM-E32. Cables have a connector on one end only (split, strip, and connect other end to graphic annunciator). Communications between the LDM series annunciators and the host AUTOPULSE control system are made through a two-wire EIA-485 multi-drop loop, and a two-wire regulated 24 VDC power loop. Up to 32 LDM systems may be connected to a single control unit, providing redundant annunciators if required. All field wiring terminations use removable, compression-type terminal blocks for ease of installation, wiring, and circuit testing. The LDM series modules, when used with a custom graphic annunciator, provide the AUTOPULSE IQ-318 control system with up to 32 unique or redundant annunciators indicating the status of the 99 software zones. When used with the IQ-636X-2, the LDM series modules provide the system with up to 32 unique or redundant annunciators, each with a capacity of 64 points for a total capacity of 2048 points. Local or remote power supplies and serial communications allow the custom annunciators to be located virtually anywhere on the protected premises. Management of system operational controls, such as signal silence and system reset, may be accomplished through special key or push switches. LDM-32 CONTROL MODULE

007255

3-39

Description (Continued)

Technical Information Size: . . . . . . . . . . . . . . . . 4.4 in. x 7.1 in. (112 mm x 181 mm) LDM-32 and LDM-E32 Output Driver: . . . . . . . . Bipolar Darlington Open Collector NPN transistor Maximum Current/Output:. . . . . . . . . . 100 mA (external current limit) Voltage Rating on Output Driver: . . . . . 30 VDC (either 24 VDC or 5 VDC) LED: . . . . . . . . . . . . . . . . . . . . . . . . . . High efficiency 2 mA LED Resistor (5 VDC):. . . . . . . . 680 Ω, 1/4 W (each LED) LED Resistor (24 VDC): . . . . . . 10K Ω, 1/4 W (each LED) Switch Rating: . . . . . . . . . . . . . . . . . . . . . 5 VDC @ 0.5 mA

LDM-E32 EXPANDER MODULE

Standby Current LDM-32: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA LDM-E32: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 mA Alarm Current LDM-32: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 mA LDM-E32: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 mA LDM-R32: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 mA

007256

LDM-R32 RELAY EXPANDER MODULE

Relay s – LDM-R32: . . . . 1 amp @ 30 VDC resistive, gold clad silver alloy

Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS100 MEA (NYC). . . . . . . . . . . . . . . . . . . . . . . . . 17-96-E, 317-01-E Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7120-0028: 156 * Listings and Approvals are under NOTIFIER.


007257

Part No.

Description

417501

LDM-32, Lamp Driver Annunciator Control Module

1

(0.5)

417502

LDM-E32, Lamp Driver Annunciator Expander Module

1

(0.5)

417650

LDM-R32, Lamp Driver Relay Module

1

(0.5)

417651

LDM-CBL24, Lamp Driver Annunciator Cable, 24 in. (610 mm)

0.5

(0.3)

417652

LDM-CBL48, Lamp Driver Annunciator Cable, 48 in. (1219 mm)

0.5

(0.3)

418576

CHS-4L, Chassis, Low Profile, For Up To 4 LDM Modules

1

(0.5)

437052

CHS-4L, Chassis, Low Profile (ULC)

1

(0.5)

CHS-4L CHASSIS 13/16 IN. (21 mm) 3 IN. (76 mm) 19 IN. (483 mm)

18 3/8 IN. (467 mm)

2 1/4 IN. (57 mm)

007258

7 IN. (178 mm)


5/16 IN. (7.9 mm)

2 1/4 IN. (57 mm) TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411


Detection and Control Components FS-24S6 and FS-24S8 6-Amp and 8-Amp 24-Volt Remote Power Supplies (IQ-318/IQ-636X-2) General The FS-24S6 (6-amp) and FS-24S8 (8-amp) are compact, cost-effective remote power supplies with battery charger. The FS-24S6/-24S8 may be connected to any 12- or 24-volt Fire Alarm Control (FA) or may be used as a stand-alone supply. Primary applications include Notification Appliance (bell) Circuit (NAC) expansion (to ADA requirements and NAC synchronization) or auxiliary power to 24-volt system accessories. The FS-24S6/-24S8 provides regulated and filtered 24 VDC power to four notification appliance circuits configured as either four Class B (Style Y) or Class A (Style Z, with ZNAC-4 option module). Alternately, the four outputs may be configured as all non-resettable, all resettable, or two non-resettable and two resettable. The FS-24S6/-24S8 also contains a battery charger capable of charging up to 18 AH batteries. Features • UL-Listed NAC synchronization using System Sensor, Wheelock, or Gentex “Commander2” appliances. • Cascadable for up to ten power supplies (four for Gentex) with strobe timing maintained. • Operates as a “sync follower” or as a “sync generator” (default). See Note on page 2. • Contains two fully-isolated input/control circuits – triggered from FA NAC (NAC expander mode) or jumpered permanently “ON” (stand-alone mode). • Four Class B (Style Y) or four Class A (Style Z, with ZNAC-4 module) NACs. • 6-amp (FS-24S6) or 8-amp (FS-24S8) full load output, with 3 amps maximum/circuit, in NAC expander mode (UL 864). • 4-amp (FS-24S6) or 6-amp (FS-24S8) continuous output in stand-alone mode (UL 1481). • Compatible with coded inputs; signals ed through. • Optional power-supervision relay (EOLR-1).

007281

• Works with virtually any UL 864 fire alarm control which utilizes an industry-standard reverse-polarity notification circuit (including unfiltered and unregulated bell power). • Requires input trigger voltage of 9.0 – 32 VDC. • Self-contained in compact, locking cabinet – 15 in. (381 mm) high x 14.5 in. (368 mm) wide x 2.75 in. (70 mm) deep. • Includes integral battery charger capable of charging up to 18 AH batteries. Cabinet capable of housing 7.0 AH batteries. • Battery charger may be disabled via DIP switch for applications requiring larger batteries. • Fixed, clamp-type terminal blocks accommodate up to 12 AWG (3.1 mm2) wire. Standards and Codes The FS-24S6/-24S8 complies with the following standards:

• In stand-alone mode, output power circuits may be configured as: resettable (reset line from FA required), nonresettable, or a mix of two and two.

• NFPA 72 National Fire Alarm Code.

• Fully regulated and filtered power output – optimal for powering four-wire smoke detectors, annunciators, and other system peripherals requiring regulated/filtered power.

• UL 1481 Power Supplies for Fire Alarm Systems (standalone mode).

• Power-limiting technology meets UL power-limiting requirements.

Specifications

• Form-C normally-closed trouble relay.

• FS-24S6/-24S8: 120 VAC, 60 Hz, 3.2 A maximum.

• Fully supervised power supply, battery, and NACs.

• Wire size: minimum #14 AWG (2.0 mm 2 ) with 600 V insulation.

• Selectable earth fault detection.

• UL 864 Standard for Control Units for Fire Alarm Systems (NAC expander mode).

Primary (AC) power:

• AC trouble report selectable for immediate or 8-hour delay. 3-40

Control input circuit:

Sync Follower/Generator Note

• Trigger input voltage: 9 to 32 VDC.

In some installations, it is necessary to synchronize the flash timing of all strobes in the system for ADA compliance. Strobes accomplish this by monitoring very short timing pulses on the NAC power which are created by the FA. When installed at the end of a NAC wire run, the FS24S6/-24S8 can track (i.e., “follow”) the strobe synchronization timing pulses on the existing NAC wire run. This maintains the overall system flash timing of the additional strobes attached to the FS.

• Trigger current: 2.0 mA (16 – 32 V). Per input: 1.0 mA (9–16 V). Trouble rating: 5 amps at 24 VDC. Auxiliary power output: specific application power 500 mA maximum. Output circuits: • +24 VDC filtered, regulated. • 3.0 amps maximum for any one circuit. • Total continuous current for all outputs (stand-alone mode): for FS-24S6: 4.0 amps maximum; for FS-24S8: 6.0 amps maximum. • Total short-term current for all outputs (NAC expander mode): for FS-24S6: 6.0 amps maximum; for FS-24S8: 8.0 amps maximum. Secondary power (battery) charging circuit: • s lead-acid batteries only.

When the FS-24S6/-24S8 is configured (via DIP switch settings) as a “sync follower,” the FS’s NAC outputs track the strobe synchronization pulses present at the FS’s sync input terminal. The pulses originate from an upstream FA or other power supply. When the FS-24S6/-24S8 is configured (via DIP switch settings) as a “sync generator,” the FS’s sync input terminals are not used. Rather, the FS is the originator of the strobe synchronization pulses on the FS’s NAC outputs. In “sync generator” mode, the sync type (System Sensor, Wheelock, or Gentex) is selectable via DIP switch settings.

• Float-charge voltage: 27.6 VDC.

Product Line Information

• Maximum charge current: 1.5 amps

FS-24S6: 6.0 amp, 120 VAC remote charger power supply. Includes main printed circuit board, transformers, enclosure (15 in. (381 mm) high x 14.5 in. (368 mm) wide x 2.75 in. (70 mm) deep), and installation instructions (Part No. 433594).

• Maximum battery capacity: 18 AH. Applications Example 1: Expand notification appliance power an additional 6.0 amps (FS-24S6) or 8.0 amps (FS-24S8). Use up to four Class B (Style Y) outputs or four Class A (Style Z) outputs (using ZNAC-4). For example, the FA notification appliance circuits will activate the FS when reverse-polarity activation occurs. Trouble conditions on the FS are sensed by the FA through the notification appliance circuit.

FS-24S8: 8.0 amp, 120 VAC remote charger power supply. Includes main printed circuit board, transformers, enclosure (15 in. (381 mm) high x 14.5 in. (368 mm) wide x 2.75 in. (70 mm) deep), and installation instructions (Part No. 433595). EOLR-1: 12/24 VDC end-of-line relay for monitoring fourwire smoke detector power.

Example 2: Use the FS to expand auxiliary regulated 24-volt system power up to 4.0 amps (FS-24S6) or up to 6.0 amps (FS-24S8). Both resettable and non-resettable power options are available. Resettable outputs are created by connecting the resettable output from the FA to one or both of the FS inputs. Example 3: Use addressable control modules to activate the FS instead of activating it through the FA notification appliance circuits. This typically allows for mounting the FS at greater distances* away from the FA while expanding system architecture in various applications. For example, an addressable control module is used to activate the FS, and an addressable monitor module is used to sense FS trouble conditions. Local auxiliary power output from the FS provides power to the addressable control module.

007282

Agency Listings and Approvals* UL Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 U.S. Coast Guard. . . . . . . . . . . . . . . . . . . . . . . 161.002/A42/1 California State Fire Marshal. . . . . . . . . . . . . . 7315-0028:225 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299-02-E *Listings and Approvals are under NOTIFIER.

BOARD LAYOUT

007283

Ordering Information Part No. Description ____ _________

Shipping Weight lb (kg) ___________

433594

FS-24S6 24-Volt Remote Power Supply

18

(8.2)

433595

FS-24S8 24-Volt Remote Power Supply

18

(8.2)



Detection and Control Components AS-610 Addressable Charger/ Power Supply (IQ-318/IQ-636X-2) General The AS-610 is an auxiliary power supply with a battery charging option and a host of special features. Selectable charging options allow the AS-610 to provide 6 amps of power to four outputs while charging batteries from 12 to 200 AH, or 10 amps of power when the unit is configured for use with an external battery charger. Four individually addressable outputs can be independently configured for auxiliary power or Notification Appliance Circuits (NAC). NAC outputs notification appliance synchronization for devices manufactured by System Sensor®, Wheelock, and Gentex. An option to disable battery charging allows the system designer to use the four built-in circuits to distribute 10 amps of power for general purposes, excluding NAC applications. The AS-610 is compatible with the AUTOPULSE IQ-318/IQ-636X-2 fire suppression control s using CLIP and FlashScan® protocol. 008022

Features • Listed to UL Standard 864, 9th Edition.

Installation Standards

• Provides 6.0 A of NAC power or 10 A of general purpose power.

The AS-610 complies with the following standards:

• Four Class B (Style Y) or four Class A (Style Z) outputs, individually addressable by the FA. • When built-in outputs are configured for NAC operation, each circuit s strobe synchronization with the following manufacturers’ audio/visual devices: System Sensor (SpectrAlert® and SpectrAlert Advance Series) or Wheelock or Gentex. • Each circuit can be software-selected for use as: a Notification Appliance Circuit, general purpose 24 VDC power, four-wire detector power, or door holder. • Steady, March Time (120 PPM), Two Stage, Temporal, or UZC Zone-Coded and Non-Coded devices – softwareselectable by circuit. • Universal Zone Coder (UZC-256) option s for programmable coded outputs. Up to 256 different codes. • Charges 12 to 200 AH batteries with full supervision. The charger on the AS may be disabled via software. When disabled, a separate, external charger is required, for example, a CHG-120. • May be used to provide battery backup for multiple AS supplies.

• NFPA 70 and NFPA 72 National Fire Alarm Code • Underwriters Laboratories UL 864, 9th Edition, Standard for Control Units for Fire Alarm Systems and CAN/ULC – S527-99. In addition, the installer should be familiar with the following standards: • NEC Article 760 Fire Protective Signaling Systems • Applicable Local and State Building Codes • Requirements of the Local Authority Having Jurisdiction Specifications • Primary (AC) power: – AS-610: 120 VAC, 50/60 Hz input, 5.0 A maximum • Output voltage: 24 VDC electrically regulated and power/limited (under primary AC mains). Under secondary power, 20.4 to 26.4 VDC. • Output circuits – TB3, TB4, TB5, TB6 on Main Board: 1.5 A maximum for any NAC output circuit. 2.5 A maximum for any Power output with battery charger disabled.

• AC loss detection, brownout detection, and AC loss delay reporting.

• Secondary power (battery) charging circuit – TB3 on KAPS-24 Board: lead-acid battery charger which will charge 12 to 200 AH batteries. Maximum charger current – 5.0 A.

• Power-limited outputs.

• Wiring: utilizes wire sizes 12 to 18 AWG (3.1 to 0.78 mm2)

• Isolated Signaling Line Circuit (SLC) interface. • Selectable ground fault detection.

• SLC specifications: Average SLC current is 1.287 mA. SLC data is transmitted between 24.0 VDC, 5 VDC, and 0 VDC at approximately 3.33 Kbaud.

• Canadian two stage operation.

• Battery fuse (F2): 15A, Slo-Blow. 3-40.1

AS Programming

Listings and Approvals

The AS-610 is programmable via the simple-to-use PK-PPS programming utility, which requires a Windows® PC with a USB port and cable. A copy of the PK-PPS programming utility is included with each AS-610. Programming may be performed during an on-line session with the AS-10, or previously saved programs may be ed to individual AS-610 units. The AS-610 requires the use of a minimum of 5 SLC address points, and will use up to 14 SLC address points to fulfill requirements for Canadian supervision and two stage operation.

UL/ULC . . . . . . . . . . . . . . . . . . . . . . . . . S635 Ordering Information AS-610: Addressable charger power supply, with selectable built-in synchronization, and four built-in control modules. Includes installation instructions and PK-PPS programming utility CD. Requires Windows PDC with USB port and USB cable. BB-25: The BB-25 can house one AS-610 and two 12 volt, 26 AH batteries. CAB-3/-4 Series: The AS-610 can mount in any of the CAB-3/-4 Series cabinets. This can be in the bottom of the cabinet or a tier via a CHS-PS and CHS-BH. CHS-6: When the power supply cannot be mounted in the CAB-3/-4 Series lowest row, the AS-610 will require the left two of the three chassis spaces.

Part No. _______

Description _________

435807

AS-610 Addressable Charger/Power Supply – 120 VAC

7

(3.2)

437344

AS-610E Addressable Charger/Power Supply – 240 VAC

7

(3.2)

008023

Example of programming for the AS-610 using 6 addresses

Shipping Weight lb (kg) __________

008024

Example for AS-610 using Canadian reporting with Two Stage



Detection and Control Components APS2-6R(E) 6.0 Amp Auxiliary Power Supply (IQ-318/IQ-636X-2) General The APS2-6R(E) is a state-of-the-art, 150 watt, switching auxiliary power supply providing 24 VDC of filtered DC power. The APS2-6R(E) provides three 24 VDC output circuits, rated for 6.0 Amps in alarm and 4.0 Amps continuous. It is used for the operation of peripheral audible/visual devices (alarm signaling appliances) for the AUTOPULSE IQ-318 or the IQ-636X-2 control s. Note: The APS2-6R(E) can also be used with Legacy s. Please refer to the APS2-6R(E) manual for more information. Features • UL 864 Ninth Edition compliant • Lightweight, compact design • 120 or 220/240 VAC (@ 50/60 Hz) versions • Output circuits with overload protection • Built-in “brown-out” circuitry • Diagnostic trouble LED • Plug-in connector for in-cabinet applications and screw terminals for remote device applications • Trouble supervision bus

008545

Construction and Operation When used with the CAB-4 Series (CAB-A4, -B4, -C4, or -D4), the APS2-6R(E) mounts to a CHS-4 or CHS-4L mounting chassis. If more than one APS2-6R(E) is necessary to meet the power requirements, connect additional APS26R(E) power supplies together as described in the Installation Instruction Manual for the APS2-6R(E).

• AC Fail supervision and reporting with field-selectable delay per UL 864

Underwriters Laboratories requires that all Signaling Appliances be approved for use with the selected control system due to voltage operating range criteria. Use only those appliances listed for use with the associated control system. Refer to Device Compatibility Document, Part No. 50054.

• Heavy-duty clamp-type terminals accept up to 12 AWG (3.1 mm2) wire

Specifications

• Battery voltage supervision

Electrical Specifications

• Low battery disconnect

• AC primary input power (TB1): APS2-6R: 120 VAC, 50/60 Hz, 2.9 A., APS2-6RE : 220-240 VAC, 50/60 Hz, 1.5 A.

• Shares battery and charger circuit with control • Power-limited design, per UL requirements

• Mounts in a standard CAB-4 Series cabinet

• DC secondary input power (TB3): TB3-1 (+), TB3-2 (–). Standards and Codes • NFPA 72 National Fire Alarm Code

• 24 VDC output power (TB2): Total 6.0 A (4.0 A continuous). Circuit 1 (TB2-1, TB2-2): 3.0 A @ 24 VDC power-limited. Circuit 2 (TB2-3, TB2-4): 3.0 A @ 24 VDC power-limited.

• UL 864 Standard for Control Units and Accessories for Fire Alarm Systems

• 24 VDC output power (J9): 6.0 A (4.0 A continuous), NonPower Limited.

In addition, the installer should be familiar with the following standards:

• Relay s (TB4): AC Fail supervision over the SLC.

This power supply complies with the following standards:

• NEC Article 300 Wiring Methods • Applicable Local and State Building Codes • Requirements of the Local Authority Having Jurisdiction • The Canadian Electrical Code, Part 1

• Fuse: (F2 battery supervision): 32 VAC, 10.0 A, Fast-Acting Automotive Minifuse. • Trouble supervision bus: J3 output: Form-A (open collector). J4 input: Form-A (open collector). Note: J3 and J4 can be interchanged. • Loss of AC indication: Immediate indication (default); 1-2 hour delay (cut JP2); 2-3 hour delay (cut JP2 and JP3).

3-41

Specifications (Continued) Mechanical Specifications The APS2-6R(E) measures approximately 8.63 in. (219 mm) x 6.63 in. (168 mm) x 2.38 in. (60 mm) and weighs approximately 2 lb (0.91 kg). Cabinet for Mounting CAB-4 Series: Use CHS-4 and CHS-4L chassis for the AUTOPULSE IQ-636X-2 control . Listings and Approvals* UL Listed . . . . . . . . . . . . . . . . . . . . . . . .S635 FM . . . . . . . . . . . . . . . . . . . . . . . . .Approved *Listings and Approvals are under NOTIFIER.

Ordering Information Shipping Weight lb (kg) _________ 2 (0.9)

Part No. _______ 436863

Description _________ APS2-6R 24-Volt Filtered Power Supply 120 VAC

436864

APS2-6RE 24-Volt Filtered Power Supply 220-240 VAC

2

(0.9)

417699

EOLR-1 12/24 VDC End-of-Line Relay

1

(0.5)

437070

EOLR-1A 12/24 VDC End-of-Line Relay (ULC)

1

(0.5)

419586

CHS-4 Four-Module Chassis

9

(4.1)

437051

CHS-4 Four-Module Chassis (ULC)

9

(4.1)

418576

CHS-4L Four-Module Chassis (Low Profile)

1

(0.5)

437052

CHS-4L Four-Module Chassis (Low Profile) (ULC)

1

(0.5)



Detection and Control Components UDACT – Universal Digital Alarm Communicator Transmitter (IQ-318/IQ-636X-2) Features • Dual phone lines • Dual telephone line voltage detect • Surface Mount Technology • Compact in size 6 3/4 x 4 1/4 inch (172 x 108 mm) • Built-in programmer • Built-in 4 character red 7-segment LED display • Manual Test Report function • Manual Transmission Clear function • Mounts in a separate enclosure (ABS-8RB) • Communicates vital system status • Annunciation of UDACT Troubles including: loss of phone lines, communication failure with either Central Station, total communication failure • Troubleshoot Mode converts keypad to DTMF touchpad • Individual LEDs for: Power, EIA-485 Loss, Manual Test, Kissoff, Comm Fail, Primary Line Seize, Secondary Line Seize, and Modem Communications • Open Collector relay driver for Total Communications Failure or UDACT trouble • Real-time clock • Extensive transient protection • Simple EIA-485 Interface to host unit

Description The Universal Digital Alarm Communicator Transmitter (UDACT) is designed for use on the AUTOPULSE IQ-318 and AUTOPULSE IQ-636X-2 control units. It is also designed for use on the Intelligent Network Annunciator (INA), software release 2.8 or higher. When used in conjunction with the INA, the UDACT can report the status of all control units on NOTI•FIRE•NET™. The UDACT transmits system status to UL listed Central Station Receivers via the public switched telephone network. The UDACT is compact in size and may be mounted externally in a separate cabinet. EIA-485 annunciator communications bus and regulated 24 volt connections are required. The UDACT is capable of transmitting the status of software zones (Alarm and Trouble), System Trouble, OffNormal, Supervisory, Bell Trouble, Low Battery, and AC Fail. When used with the AUTOPULSE IQ-318 and IQ-636X-2 the UDACT is capable of reporting 567 points. Reporting may be in the form of software zones (99 plus 16 special), circuits 1-4, output modules 1-64, and 192 points per SLC loop (the first 96 detector and 96 module addresses). The Universal Digital Alarm Communicator Transmitter (UDACT) provides the means to create a powerful, low cost, local area network solution for any application involving multiple facilities spread over a small geographic area, such as hospitals, college campuses, shopping malls, prisons, airports, grouped government facilities, power plants, large commercial facilities, and much more.

UDACT IN ABS-8R (SHOWN WITH COVER REMOVED)

LOCAL AREA NETWORK

TO AUTOPULSE IQ-636X-2 TO SUPERVISED PHONE LINES

SOLID EARTH GROUND

BUILDING

LOCAL TELEPHONE CENTRAL OFFICE NETWORK

002374

AUTOPULSE IQ-318

UL LISTED PRIMARY CONTROL STATION (IF REQUIRED)

UDACT MODEM

002373

3-42

The UDACT when used in the ID format transmits detailed system status via the standard public switched telephone network to a digital receiver. The telephone network becomes the “network gateway” from the FA to the digital receiver and to an optional UniNet monitor. ID is a transmission format enabling transmission of alarm and trouble conditions on a bi-point basis. Three groups of information are transmitted to the central station: a four-digit code, a group number (00-99), and the device or zone number (000-999). Each of these three information groups is programmable. Because of the virtually unlimited number of combinations, the number of systems, points and/or zones transmitted is boundless.

Technical Information Standby current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA Current while communicating: . . . . . . . . . . . . . . . . . . . 75 mA Maximum current while communicating and with open collector output activated: . . . . . . . . . . 100 mA Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulated 24 volts Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.2 to 28.2 volts Required software: • IQ-301 EPROM = 73609 (or higher) • IQ-396X EPROM = #AFP4R 2.0 (or higher) • IQ-318 = All • IQ-636X = All • IQ-636X-2 = All

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS100 Vol. VII Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7300-0028:174 MEA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328-94-E Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . 2132 6030 A FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . IWGUSA-20723-AL-E * Listings and Approvals are under NOTIFIER

Ordering Information Shipping Weight lb (kg) __ ____

Part No. _________ Description ______ 419411 UDACT Universal Digital Alarm COM/XMTR

2

(0.9)

436996

1

(0.5)

Sencoa 3000R (7)

Surguard MLR-2 (9)

ABS-8RB Surface Back Box

COMPATIBILITY CHART Silent Knight 9000

Format # (Addresses 16 & 42)

Ademco 685 (1)

4+1 Ademco Express

⻫

1

4+2 Ademco Express

⻫

2

3+1/Standard/1800/2300

⻫

⻫ (2)

3

(Not Used)

4

3+1/Standard/1900/1400

⻫

⻫ (2)

5

(Not Used)

6

4+1/Standard/1800/2300

⻫

⻫(2)

7

(Not Used)

8

4+1/Standard/1900/1400

⻫

⻫ (2)

9

(Not Used)

A

4+2/Standard/1800/2300

⻫

⻫ (2)

B

(Not Used)

C

4+2/Standard/1900/1400

⻫

⻫ (2)

D

(Not Used)

E

Ademco ID

F

(Not Used)

0

ITI CS-400 (3)

Radionics 8000/ 5800 (5)

⻫

⻫

(1) With 685-8 Line Card with Rev 4.4d software (2) With 9002 Line Card Rev 9035 software or 9032 Line Card with 9326A software (3) Rev 4.0 software. (4) FBI 220FB Rec-11 Lin Card with Rev 2.6 software and a memory card with Rev 3.8 software TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411

FBI 220FB

Osborne Hoffman Models 1&2

⻫

⻫

⻫

⻫

⻫

⻫(8)

⻫ (4)

⻫

⻫ (4)

⻫

⻫ (4)

⻫

⻫ (4)

⻫

⻫ (4)

⻫

⻫ (4)

⻫

⻫

⻫

⻫⻫ (5,6)

⻫ (5)

⻫ (5)

⻫

⻫

⻫

⻫

⻫

⻫

⻫

⻫

⻫

⻫

⻫

⻫⻫

(5) Model 6500 with Rev 600 software (6) Model 6000 with Rev 204 software (7) With Rev B control card at Rev 1.4 software and Rev C line card at Rev 1.5 software (8) Model 2 only (9) Version 1.62 software Copyright © 2011 Tyco Fire Protection Products All rights reserved. Form No. T-2007109-3





Detection and Control Components CHG-120 Battery Charger and Meters (IQ-318/IQ-636X-2) Features • Charges sealed lead-acid batteries • Automatic float-type battery charger • Rated for batteries of 25 to 120 ampere-hours • Obtains full float voltage within 48 hours • For use on any 24-volt FA which can handle the specified batteries and can disable the local charger • AC Fail delay (central station applications) per latest NFPA requirements • Form-C Trouble • Dual outputs, for easy load distribution • Diagnostic LEDs: Primary AC On Charger Trouble Ground Fault Hi Charge Lo Charge Battery Voltage Level (3 LEDs) Low Battery • Optional BB-55 battery cabinet • Field-selectable input voltage, 120 VAC or 230 VAC • Charges: 25 AH batteries within 9 hours 55/60 AH batteries within 20 hours 120 AH batteries within 38 hours

Applications Use the CHG-120 battery charger with the AUTOPULSE IQ-318 or IQ-636X-2 control units when batteries required for standby are rated equal to or greater than 25 ampere-hours. Up to two batteries may be charged when either the 25AH or 60AH are installed. Description The CHG-120 battery charger is a state-of-the-art battery charging system designed for use with the AUTOPULSE IQ-318 or IQ-636X-2. It is designed to charge lead-acid batteries between 25 and 120 ampere-hours (AH). The CHG-120 consists of a PC board and mounting chassis. Charging current is provided automatically when the battery voltage falls below the charger’s output voltage.

CHG-120 BATTERY CHARGER

VOLTAGE SELECTION SWITCH FOR 115 VAC OR 230 VAC OPERATION

NINE LED STATUS INDICATORS OPEN COLLECTOR TROUBLE DAISY CHAIN CONNECTIONS EXTERNAL TROUBLE INPUT

FORM-C RELAY TO OTHER DEVICES TWO OUTPUT CIRCUITS TO LOAD (POWER SUPPLY, AUXILIARY POWER SUPPLY, AMPLIFIER, ETC.)

25 AH-120 AH BATTERY CONNECTIONS 15A REPLACEABLE FUSES PROVIDE SHORT CIRCUIT AND OVERLOAD PROTECTION OPTIONAL AMMETER CONNECTION 003575

3-44

Technical Information Primary AC power in (TB1): . . . . . . . . . . 115 VAC, 60 Hz, 2 A 230 VAC, 50 Hz, 1 A Form-C relay (TB3): . . . . . . . . . . . . . . . . . . . . . 5 A at 30 VDC Float charge voltage: . . . . . . . . . . . . . . . . . . . . . . . . 27.6 VDC Maximum charging current:. . . . . . . . . . . . . . . . . . . . . . . 4.5 A Fuses F1-F3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 A Battery sizes: . . . . . . . . . . . . . . . . . . . . . . . . 25 AH to 120 AH Charging time (for 2 fully discharged batteries) 25 AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Hours 55 AH/60 AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hours 120 AH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Hours High: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5/8 in. (118 mm) Wide:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 in. (76 mm) Deep: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3/4 in. (44 mm)

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S674 ULC. . . . . . . . . . . . . . . . . . . . . . . . . . . CS118/CS733 VOL. IX Factory Mutual (FM). . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal (CSFM) . . . . . . 7315-0028:189 MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195-97-E *Listings and Approvals are under NOTIFIER.


Part No. ______ 426207

Description _________ CHG-120 Battery Charger

Shipping Weight lb (kg) ________ 5.0

(2.3)

Mounting Options The CHG-120 has a variety of mounting options. It can be mounted in either a CAB-3 or CAB-4 or remotely in the BB-55 Battery Back Box. Install the CHG-120 within 20 ft (6.01 m) of the main AUTOPULSE control unit. Mounting in CAB-3 or CAB-4 Series Backbox: The CHG-120 can be mounted in the main power supply position, on the lower left of the CAB-3 or CAB-4 cabinet. Using self-tapping screws, the CHG-120 can be mounted in the lower right position (normally, where the batteries are mounted) of the CAB-3 or CAB-4. Remote mounting in the BB-55: The CHG-120 mounts in the left position of the cabinet. Note: Only one 60AH, 12V battery or two 25AH, 12 V batteries will mount with the charger board in the BB-55. BB-55 Battery Box Battery Configurations: Without CHG-120 mounted internally: Up to two 25AH, 12V batteries Up to two 60AH, 12V batteries With CHG-120 mounted internally: Up to two 25AH, 12V batteries Up to one 60AH, 12V battery




Annunciator Back Boxes (IQ-318/IQ-636X-2) Description The Annunciator back boxes are used for mounting the LCD-80, AEM, ACS, or AFM annunciator modules. ABS-1B – The Annunciator Surface Box-1 provides for the remote mounting of a single ACM or AFM annunciator in a surface-mount enclosure. Knockouts are provided for use with 1/2 in. conduit. The annunciator mounts directly to the ABS-1B without a dress plate. ABS-2B – The Annunciator Surface Box-2 provides for the surface mounting of one ACM-16AT/AEM-16AT combination or one ACM-32A/AEM-32A combination. Knockouts are provided for use with 1/2 in. conduit. The annunciators mount directly to the ABS-2B without a dress plate.

ABF-1B – The Annunciator Flush Box-1 provides for the remote mounting of a LCD-80 or a single ACM or AFM annunciator in a flush-mount enclosure. Knockouts are provided for use with 1/2 in. conduit. The ABF-1B includes a painted gray metal trim plate, mounting hardware, and an adhesive-backed Annunciator Label for the dress plate. ABF-1B FLUSH BACK BOX 9 15/16 IN. (H) x 4 5/8 IN. (W) x 2 1/2 IN. (D) (252 mm (H) x 117 mm (W) x 64 mm (D)) TRIMPLATE: 11 IN. (H) x 6 1/4 IN. (W) (279 mm (H) x 159 mm (W))

WIDTH

ABS-1B AND ABS-2B SURFACE BACK BOXES ABS-1B: 8 1/2 IN. (H) x 4 1/2 IN. (W) x 1 3/8 IN. (D) (216 mm (H) x 114 mm (W) x 35 mm (D)) ABS-2B: 8 1/2 IN. (H) x 8 15/16 IN. (W) x 1 3/8 IN. (D) (216 mm (H) x 227 mm (W) x 35 mm (D))

HEIGHT

HEIGHT WIDTH

WIDTH

007262

DEPTH

ABS-1TB – The ABS-1TB is an attractive surface mount back box for mounting a LCD-80 or one ACM or AFM annunciator. HEIGHT

ABS-1TB SURFACE BACK BOX 2 1/2 IN. (64 mm)

4 5/8 IN. (117 mm)

007372

DEPTH

9 15/16 IN. (252 mm)

007261

3-45

Technical Information Box Type Annunciator Compatibility ABS-1B ACM-16AT, ACM-32A, AFM-16AT, AFM-32A ABS-2B ACM-16AT/AEM-16AT, ACM-32A/AEM-32A ABF-1B* LCD-80, ACM-16AT, ACM-32A, AFM-16AT, AFM-32A ABS-1TB LCD-80, AFM-16AT, AFM-32A, ACM Type with AKS-1B (key switch) *Includes painted black metal trim plate

Approvals UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 Ordering Information Shipping Weight lb (kg)

Part No.

Description

417657

ABF-1B, Annunciator Back Box, Flush, Single

1

(0.45)

417493

ABS-1TB, Annunciator Back Box, 1 Surface Single, Deep

(0.45)

417660

AKS-1B, Annunciator Key Switch

(0.45)


1


Detection and Control Components FDU-80G 80-Character Liquid Crystal Display Fire Annunciator (IQ-318/IQ-636X-2) General The FDU-80G is a compact, 80 character, backlit LCD Fire Annunciator for use with the AUTOPULSE IQ-318 and IQ-636X-2 Fire Alarm Control s (FAs). The FDU-80G mimics the display of the control and displays complete system point status information. Up to 32 FDU-80Gs may be connected onto the EIA-485 Terminal Mode port of each control . The FDU-80G requires no programming, which saves times during system commissioning. The FDU-80G can be used on the same data loop as the LCD-80/LCD-80TM annunciators revision 1.6 software or higher. 007714

Features • 80-character Liquid Crystal Display

Operation

• Mimics all display information from the host

The FDU-80G annunciator provides the FA with point annunciation with full display text on an 80-character LCD display. The FDU-80G also provides an array of LEDs to indicate system status, and also includes control switches for remote control of critical system functions.

• Control switches for System Acknowledge, Signal Silence, Drill and Reset with enable key • System status LEDs for Power, Alarm, Trouble, Supervisory, and Alarm Silenced • No programming necessary – FDU-80G connects to the terminal mode port • Displays device type identifiers, individual point alarm, trouble or supervisory, zone and custom alpha labels • Time and date display field • Aesthetically pleasing design • May be powered by 24 VDC from the host FA or by remote power supplies (requires 24 VDC) • Up to 32 FDU-80G annunciators per FA • Plug-in terminal blocks for ease of installation and service

The FDU-80G provides the FA with up to 32 remote serially connected annunciators. All field-wiring terminations on the FDU-80G use removable, compression-type terminal blocks for ease of wiring and circuit testing. Communication between the FA and the annunciators is accomplished over an EIA-485 serial interface, which greatly reduces wire and installation cost over traditional systems. Six wires total are required: four for the EIA-485 communications (two in and two return); and two for the 24 VDC regulated power. Dip switches control local functions such as: piezo disable, control switches/key switch disable, transmit/receive mode.

• Can be remotely located up to 6,000 ft (1828.8 m) from host control • Local piezo sounder with alarm and trouble resound • Semi-flush mounts to 2.188 in. (56 mm) minimum deep, three-gang electrical box or three-gangable electrical switchbox • Surface mounts to SBB-3 surface backbox

3-46

FDU-80G Terminal Mode Wiring Example UP TO 6,000 FT (1828.8 m) BETWEEN EACH DEVICE IN THE EIA-485 LOOP FDU-80G

FDU-80G

TERMINAL MODE EIA-485 (2 WIRES) TO CONTROL

24 VDC (2 WIRES) UP TO 6,000 FT (1828.8 m) BACK FROM LAST DEVICE TO END OF EIA-485 LOOP

FDU-80G

TERMINAL MODE EIA-485 RETURN (2WIRES)

007716

Notes: 1. EIA-485: Maximum of 6,000 ft (1828.8 m) cable length from FA to FDU-80G annunciators and back to FA (6,000 ft (1828.8 m) total). Circuit is power limited. 2. Up to 32 FDU-80G annunciators may be used on the EIA-485 circuit. When multiple FDU-80Gs are used, certain s will require additional power supplies (refer to documentation). 3. Between each FDU-80G annunciator are four wires: a twisted-shielded pair for data communications and a pair for 24 VDC power. The return circuit only requires two wires for data communication supervision, wired from the last FDU-80G annunciator on the loop. 4. The FDU-80G annunciator can be semi-flush mounted in a three-gang electrical box with a minimum depth of 2.188 in. (5.6 cm). Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal . . . . . . . . . . . . . 7120-0028:209 *Listings and Approvals are under NOTIFIER.


Part No. _______ 435530

Description _________ FDU-80G Annunciator

Shipping Weight lb (kg) __________ 5.0 (2.3)

436141

SBB-3, Back Box, Surface

2.0


(0.9)


Detection and Control Components LCD2-80 Liquid Crystal Display Terminal Mode Annunciator (IQ-318, IQ-636X-2) General The LCD2-80 is a backlit LCD annunciator for the Addressable AUTOPULSE fire suppression control s that the 80-character display format. The LCD2-80 may be connected onto the four-wire EIA-485 terminal port. The LCD2-80 mimics the display of the IQ-318 and IQ-636X-2 control s, the NCA-2 annunciator, and legacy s (IQ-301, IQ-396X, and IQ-636X) that ed the LCD-80/LCD-80TM. Up to 32 LCD2-80 units can annunciate and provide remote reset, acknowledge, drill and silence of the control from remote locations. Note: The LCD2-80 can be used with legacy s that ed the LCD-80 terminal mode operation. Please refer to the LCD2-80 manual for more information. Features • 80-character backlit Liquid Crystal Display (20 characters x 4 lines) • Display mimics or NCA annunciator – Event message – 20 characters for point label – 12 characters for extended label – Time, date, and point address

008850

• Flush/surface/ mount option

• Control switches for System Acknowledge, Signal Silence Drill, and System Reset • Mounts up to 6,000 ft (1828.8 m) segments between units

• No programming necessary; LCD2-80 displays time, date, and custom messages received from the compatible or network annunciator • LCD2-80 is 8.25 in. (210 mm) high, 4.375 in. (111 mm) wide, and 1.75 in. (44 mm) deep

• Local piezo sounder with alarm/trouble resound • Displays all analog, addressable points

• Up to 32 LCD2-80 annunciators may be used on one EIA-485 circuit

• Displays device type identifiers • Displays device and zone custom alpha labels

Note: The LCD2-80 must have sufficient regulated 24-volt power.

• Mounts to any CHS-4 chassis slot • Slide-in label can be customized

6,000 FT (1828.8 m) MAXIMUM WIRE LENGTH BETWEEN EACH LCD2-80 EIA-485 (2 WIRES)

24 VDC (2 WIRES)

EIA-485 RETURN (2 WIRES) 008851

IQ-318, IQ-636X-2 or NCA-2 Connecting to LCD2-80

3-46.1

Agency Listings and Approvals These listings and approvals apply to the modules specified in this document. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approved FDNY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COA# 6067, 6065 CSFM . . . . . . . . . . . . . . . . 7165-0028:0243, 7165-0028-0224 Ordering Information LCD2-80: Liquid Crystal Display Terminal Mode Annunciator. May be connected onto the four-wire EIA-485 terminal port. ADP-4B: Annunciator dress plate, black. Allows mounting of up to four LCD2-80 modules in a CAB-4 Series cabinet. ABF-1B: Annunciator flush box, 9.938 in. (252 mm) high, 4.625 in. (117 mm) wide, and 2.5 in. (64 mm) deep. Order AKS-1B key switch. ABS-1TB: Deep surface back box (mounts one LCD2-80). AKS-1B: Key Switch (black) to enable/disable controls when mounted in ABF-1B or ABS-1TB. Shipping Weight lb (kg) _____________

Part No. _______

Description _________

438773

LCD2-80 Terminal Mode Annunciator

2

(0.9)

433520

ADP-4B Annunciator Dress Plate

1

(0.5)

417657

ABF-1B Annunciator Back Box, Flush, Single

1

(0.5)

417493

ABS-1TB Annunciator Back Box, Surface, Deep

1

(0.5)

417660

AKS-1B Annunciator Key Switch

1

(0.5)


Copyright © 2011 Tyco Fire Protection Products All rights reserved. Form No. T-2011199

Detection and Control Components NCA-2 AUTOPULSE Series Network Control Annunciator (IQ-318/IQ-636X-2) General The NOTIFIER NCA-2 is a second-generation Network Control Annunciator compatible for use with AUTOPULSE IQ-318 and IQ-636X-2 fire alarm control s, as well as first-generation NCA Network Control Annunciators. The NCA-2 provides system control and display capabilities. The NCA-2 display consists of a 640-character backlit LCD display, and a control interface consisting of “soft” keys used to navigate screen menus, “hard” keys with fixed control functions, and a QWERTY keypad. Hardware Features • Listed to UL Standard 864, 9th edition • Full supervision of all inputs and network integrity • Enhanced-format 640-character LCD display with backlighting • ACS bus for LED or graphic annunciators (EIA-485) • Optically isolated printer interface (EIA-232) • 11 LED status indicators: Power, Controls Active, Fire Alarm, Pre-Alarm, Security, Alert, Supervisory, Trouble, Signal, Silence, U Failure, Point Disabled, Other Event • Alphanumeric QWERTY rubber keypad

007715

• Enhanced Read Status/Alter Status displays • New history filters for report displaying and printing: All Events, Only Alarms, Only Troubles, Only Supervisory, Only, Security, Time Interval, Point Range

• Four status relays: Alarm, Trouble, Supervisory, Security (Form-C)

• Advanced/Basic Walk-Test program

• Nonvolatile real-time clock can be synchronized with network by master node

• Meets Canadian ULC display requirements

• Optional Security Keyswitch enable Keypad functions

• Environmental adjustment controls to maximize LCD legibility

• Optional Security Tamper switch • s up to 32 remote ACS annunciators and modules

• Timer control for Auto Silence, AC Fail Delay

• Meets NFPA requirements for Firefighter Smoke Control Station (FSCS) and HVAC

• Requires 24 VDC and a network connection NCA-2 Indicators and Controls Function Features

LED Indicators:

• Individual Enable/Disable or Group Enable/Disable local for networked AUTOPULSE series s

• Power (green) illuminates when 24 VDC power is applied; LED goes out if power is removed and NCA-2 is using a battery.

• Lamp Test (local to NCA-2) • History Buffer (1000 Alarm events; 4000 System events) • Print NCA-2 programming and history reports • Report status of s and their respective field devices to a central station via a single UDACT • One Master level, nine level s: The Master can assign each access levels (programming, alter status) • Interactive Summary Event Count display, event handling package • Online programming and alter-status programs

• Controls Active (green) illuminates to indicate that the NCA-2 control functions are active. • Fire Alarm (red) illuminates when at least one fire alarm event exists; flashes when any of these events remain unacknowledged. • Pre-Alarm (red) illuminates when at least one pre-alarm event exists; flashes when any of these events remain unacknowledged. • Security (blue) illuminates when at least one security event exists; flashes when any of these events remain unacknowledged

• Intuitive guidance program including interactive soft keys 3-47

NCA-2 Indicators and Controls (Continued)

Special Function Keys

LED Indicators: (Continued)

• Print Screen: Press this key to print what is currently on the LCD screen.

• Supervisory (yellow) illuminates when at least one supervisory event exists (i.e., sprinkler valve off normal, low pressure, fire pump running, guard’s tour, etc.); flashes when any of these events remain unacknowledged. • System Trouble (yellow) illuminates when at least one trouble event exists; flashes when any of these events remain unacknowledged.

• Lamp Test: Press this key to test the LED indicators on the left of the keypad and to check firmware revision numbers. • Next Selection/Previous Selection: These keys are used when setting parameters in NCA-2 data fields; for example, choosing a device type as a filter for requesting a Node History.

• Other Event (yellow) illuminates for any category of event not listed above; flashes when any of these events remain unacknowledged.

• Battery Level: Press this key to display voltage and charging current level for system batteries.

• Signals Silenced (yellow) illuminates if the NCA-2 Silence key has been pressed or if any other node sent a Network Silence command; flashes if only some points on a node are silenced.

Specifications

• Point Disabled (yellow) illuminates when at least one disable exists on the network or in the system. • U Failure (yellow) activated by the watchdog timer hardware, indicates an abnormal hardware or software condition. technical . Fixed Function Keys • Acknowledge • Signal Silence • System Reset • Drill • Fire Alarm Scroll/Display • Security Scroll/Display • Supervisory Scroll/Display • Trouble Scroll/Display • Other Event Scroll/Display The five keys labeled Scroll/Display allow the to scroll through messages for the particular event type. For example, pressing the Fire Alarm Scroll/Display key will scroll through all fire alarm events, as details of each are shown in the display area of the NCA-2. Note: The Other Event Scroll/Display key also scrolls between Pre-Alarm and Disabled events. • Acknowledge: Press this key to acknowledge off all active events. • Signal Silence: Press this key to turn off all control modules, notification appliance circuits, and output circuits that have been programmed as Silenceable. • System Reset: Press this key to clear all latched alarms and other events and turn off event LEDs. • Drill Hold 2 Sec: Press this key, holding it down for two seconds, to activate all silenceable output circuits.

Temperature and humidity ranges: This system meets NFPA requirements for operation at 32 °F-120 °F (0 °C-49 °C) and at a relative humidity (noncondensing) of 85% at 86 °F (30 °C) per NFPA, and 93% ± 2% at 89.6 °F ± 1.1 °F (32 °C ± 2 °C) per ULC. However, the useful life of the system’s standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and all peripherals be installed in an environment with a nominal room temperature of 60 °F-80 °F (15 °C-27 °C). Electrical Requirements The NCA-2 may be powered from a Main Power Supply AMPS-24(E) mounted in the NCA-2 cabinet (see specifications below); or from any UL Listed non-resettable 24 VDC source from an AUTOPULSE control . The battery on the NCA-2 motherboard is for RTC and SRAM; holds the history memory through power failure. Replacements are available. Power source: 1) AMPS-24 (120 VAC, 50/60 Hz, 4.5 A maximum) or AMPS-24E (240 VAC, 50/60 Hz, 2.25 A maximum) power supply; 2) the AUTOPULSE IQ-636X-2 on-board power supply; or 3) a supervised +24 VDC power supply that is UL/ULC Listed for fire protective service Total output 24 VDC power: 4.5 V in alarm. Listings and Approvals* These listings and approvals apply to the NCA-2. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 CSFM . . . . . . . . . . . . . . . . . . 7165-0028:243, 7170-0028:244 MEA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128-07-E *Listings and Approvals are under NOTIFIER.

Ordering Information Part No. _______ 434956

Description _________ NCA-2 (Network Control Annunciator)

Shipping Weight lb (kg) _____________ 5.0 (2.3)

ONYX and NOTIFIER are ed trademarks of Honeywell International Inc.



Detection and Control Components VeriFire™ Tools Programming and Test Utility (IQ-318, IQ-636X-2, NCA-2) General VeriFire™ Tools is a programming and test utility for the AUTOPULSE IQ-318, IQ-636X-2, and NCA-2 with offline and online capabilities that can greatly reduce installation programming time and increase confidence in the sitespecific software. It is Windows® based and provides technologically advanced capabilities to aid the installer. The installer may create the entire program for the control in the comfort of the office, test it, store a backup file, then bring it to the site and from a laptop into the . The program includes error checks for common programming mistakes, such as an input point that does not activate any outputs, or an output point that is not linked to any inputs. In online mode, s can perform point “read status” functions, change and device labels, and change detector sensitivities. VeriFire™ Tools includes a compare routine, pictured at right, that can also greatly help the installer. When a new program is created, it may be compared with a previous version and differences are highlighted. If the program is modified from the keypad, it may be ed into VeriFire™ Tools, and compared with the previous version stored on disk. The identification of program differences greatly helps the installer in testing the installation. NFPA 72 requires that reacceptance test of a fire alarm system be performed on 100% of all points that are “known” to be modified. VeriFire™ Tools allows the installer to determine the exact points that are changed. Product Line Information 433365 – VeriFire™ Tools CD-ROM. Contains programming software for the AUTOPULSE IQ-318, IQ-636X-2, and NCA-2. Includes local hardware connection. 432798 – VeriFire™ Tools CD-ROM contains software only. PC Specifications (minimum requirement) • Pentium® II 300 MHz • 64 MB of RAM • 50 MB of hard drive space • Windows® 98 Second Edition, ME, NT, 2000, or XP (Windows® 95 is not ed) • Serial port • XGA video (1024 x 768)

VeriFire™ is a trademark of Honeywell International. Microsoft® and Windows® are ed trademarks of Microsoft Corporation. Pentium® and Intel® are ed trademarks of Intel Corporation.



Detection and Control Components SLR-24H Photoelectric/Heat Smoke Detector (IQ-318/IQ-636X-2 (with FZM)) Features • Self-restoring integral 135 °F (57 °C) heat sensor, 50 ft (15 m) rating • Low profile, 2.4 in. (60 mm) high – with base • 2 or 4 wire base compatibility, relay bases available • Highly stable operation, RF/Transient protection • Low standby current, 45μA at 24 VDC • Two built-in power/sensitivity supervision/alarm LEDs • Non-directional smoke chamber • Vandal resistant security locking feature • Built-in magnetic go/no go detector test feature • Removable smoke labyrinth for cleaning or replacement • Automatic Sensitivity window verification function meets outlined requirements in NFPA 72, Chapter 7, Inspection, Testing and Maintenance • Backwards compatible with SLK and SIH detectors Applications The SLR-24H Photoelectric/Heat Smoke Detectors are intended for use in commercial, industrial, and institutional buildings. The detectors are placed primarily in clean, indoor environments where early warning fire detection is required. It is best suited for smoldering or flaming fires. The 135 °F (57 °C) heat sensor can initiate an alarm independently. The heat detector is UL listed for 50 ft (15 m) spacing when used for evacuation alarm, if used for suppression release the spacing should be reduced. The detectors are used in combination with an AUTOPULSE Control System and a fire suppression system for automatic detection, alarm, equipment control, and fire suppression system release capabilities. Description The SLR-24H photoelectric/heat smoke detector utilizes two bicolor LEDs for indication of status. In a normal standby condition the LEDs flash Green every 3 seconds. When the detector senses that its sensitivity has drifted outside the UL listed sensitivity window, the LEDs will flash Red every 3 seconds. When the detector senses smoke and goes into alarm, the status LEDs will latch on Red. The detector utilizes an infrared LED light source and silicon photo diode receiving element in the smoke chamber. In a normal standby condition, the receiving element receives no light from the pulsing LED light source. In the event of a fire, smoke enters the detector smoke chamber and light is reflected from the smoke particles to the receiving element. The light received is converted into an electronic signal. Signals are processed and compared to a reference level, and when two consecutive signals exceeding the reference level are received within a specified period of time, the time delay circuit triggers the SCR switch to activate the alarm signal. The status LEDs light continuously during the alarm period.

DIMENSIONS – NS6-224 BASE TO 4 IN. (102 mm) SQUARE OR 4 IN. (102 mm) OCTAGON OUTLET BOX

7/16 IN. (11 mm)

5 7/8 IN. (149 mm)

004630

2 5/16 IN.

004641

(59 mm)

DIMENSIONS – NS4-224 BASE TO 3 IN. (76 mm) OCTAGON OUTLET BOX

5/16 IN. (8 mm)

3 15/16 IN. (100 mm)

2 5/16 IN. (59 mm)

004625a 004642

DIMENSIONS – HSB-21 BASE 9/16 IN. (14 mm)

TO 4 IN. (102 mm) SQUARE OUTLET BOX

5 7/8 IN. (149 mm)

004624a

2 3/8 IN. (60 mm)

TO 3 IN. (76 mm) OR 4 IN. (102 mm) OCTAGON OUTLET BOX

004641

DIMENSIONS – HSC-224RA BASE 1 1/8 IN. (29 mm)

TO 4 IN. (102 mm) SQUARE OR 4 IN. (102 mm) OCTAGON OUTLET BOX

5 7/8 IN. (149 mm)

004626a

2 15/16 IN. 004643

(75 mm)

3-49

Technical Information Detector Base/Control Unit Compatibility Detector AUTOPULSE _______________ Base IQ-318, IQ-636X-2 (Part No.) FZM-1 NS6-224 (427598) Yes HSB-21 (417457) No NS4-224 (427599) Yes HSC-224RA (416849) No Heat Detector: . . . . 135 °F (57 °C) self-restoring, fixed temp. Light Source: . . . . . . . . . . . . . GaAl as infrared emitting diode Rated Voltage: . . . . . . . . . . . . . . . . . . . . . . . 17.6 to 33.0 VDC Working Voltage:. . . . . . . . . . . . . . . . . . . . . . . 15 to 33.0 VDC Maximum Allowable Voltage: . . . . . . . . . . . . . . . . . . . 42 VDC Supervisory Current:. . . . . . . . . . 45 μA maximum @ 24 VDC Surge Current: . . . . . . . . . . . . . 160 μA maximum @ 24 VDC Alarm Current: . . . . . . . . . . . . . 150 mA maximum @ 24 VDC Ambient Temperature: . . . . +32 °F to +120 °F (0 °C to 49 °C) Color: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bone White Sensitivity Test Feature: . . . . . . Automatic sensitivity window verification test Air Velocity:. . . . . . . . . . . . . . . . . . . . . . . . Maximum 300 FPm WIRING DIAGRAM – TWO WIRE OPERATION NS4 AND NS6 SERIES BASE RESISTOR SHOWN IS FOR EXAMPLE ONLY. NOT ALL ANNUNCIATORS HAVE IN-LINE RESISTANCE.

LISTED END OF LINE DEVICE

UL LISTED CONTROL POWER SUPPLY

Mounting Guidelines The detector bases are designed for surface mounting. The detector head can be inserted or removed from the base without disrupting the wiring connections. The following bases are compatible with the SLR-24H Photoelectric/Heat Smoke Detector: Base Type of Mounting Box HSB-21 4 in. (102 mm) Octagon, 4 in. (102 mm) Square NS4-224 3 in. (76 mm) Octagon NS6-224 4 in. (102 mm) Octagon, 4 in. (102 mm) Square HSC-224RA 4 in. (102 mm) Octagon, 4 in. (102 mm) Square HSC-224RA RELAY TERMINAL STRIP @@@@@@@@e? @@@@@@@@e?@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e? @@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ @@@@@@@@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

ORANGE WIRE

C

1

VIOLET WIRE

NC

2

YELLOW WIRE

NO

3

GRAY WIRE

NO

4

GREEN WIRE

NC

5

C

6

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

BLUE WIRE

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

TB1 CONNECTIONS

@@ @@ @@ @@ @@ @@ @@ @@

@@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@@@@@@@ @@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@ ?@@@@@@@@

004629

Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S1383 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS463 California State Fire Marshal (CSFM). . . . . . . 7272-0410:107 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . 1O5A1.AY MEA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284-91-E * Listings and Approvals are under HOCHIKI AMERICA CORPORATION

NEGATIVE


430 OHM RESISTOR IN4003 DIODE MUST BE INSTALLED IN SERIES WITH THE 430 OHM RESISTOR WHEN BASE IS USED TO OPERATE REMOTE LED.

ANNUNCIATION DEVICE MUST BE 4 CURRENT LIMITED TO 20 mA @ 24 VDC 3 MAXIMUM. NOT LIMITING CURRENT 5 COULD RESULT IN DAMAGE TO 6 004627 THE DETECTOR OR CAUSE A NOTE: WIRING TERMINALS FOR THE NS4 NO ALARM CONDITION. AND NS6 ARE IDENTICAL. BASES WITH THE “W” SUFFIX ARE WHITE IN COLOR.

WIRING DIAGRAM – HSB-21 AND HSC-224RA* STANDARD BASES, STYLE B EOL RESISTOR (+)


Part No.

Description

427597

SLR-24H Photoelectric/ Heat Smoke Detector NS6-224 Base NS4-224 Base HSB-21 Base HSC-224RA Relay Base Test Magnet Punk Stick (Pack of 10)

427598 427599 417457 416849 415730 405491

1

(0.4)

0.5 0.5 0.5 0.5 0.5 0.5

(0.2) (0.2) (0.2) (0.2) (0.2) (0.2)

S1

S1 L3 L4 S2 L2

L3 L4 S2 L2

(+)

(+)

(–) (–)

(–)

*REMOTE LED (16 mA MAX)

(–)

REMOTE LED

004628

SYSTEM COMMON (DC RETURN) * Do not wire HSC-224RA to remote LED as shown. Annunciation for the relay base (HSC-224RA) must be wired to the relay s using external power.



Detection and Control Components SLR-24 Photoelectric Smoke Detector (IQ-318/IQ-636X-2 (with FZM)) Features • Low profile, 1.8 in. (46 mm) high – with base • 2 or 4 wire base compatibility, relay bases available • Highly stable operation, RF/Transient protection • Low standby current, 45μA at 24 VDC • Two built-in power/sensitivity supervision/alarm LEDs • Non-directional smoke chamber • Vandal resistant security locking feature • Built-in magnetic go/no go detector test feature • Removable smoke labyrinth for cleaning or replacement • Automatic Sensitivity window verification function meets outlined requirements in NFPA 72, Chapter 7, Inspection, Testing and Maintenance • Backwards compatible with SLK and SIH detectors Applications The SLR-24 Photoelectric Smoke Detectors are intended for use in commercial, industrial, and institutional buildings. The detectors are placed primarily in clean, indoor environments where early warning fire detection is required. The detectors are used in combination with an AUTOPULSE Control System and an fire suppression system for automatic detection, alarm, equipment control, and fire suppression system release capabilities.

DIMENSIONS – NS6-224 BASE TO 4 IN. (102 mm) SQUARE OR 4 IN. (102 mm) OCTAGON OUTLET BOX

5 7/8 IN. (149 mm)

004630

004631b

DIMENSIONS – NS4-224 BASE

1 7/8 IN. (47 mm) 5/16 IN. (8 mm)

TO 3 IN. (76 mm) OCTAGON OUTLET BOX

3 15/16 IN. (100 mm)

004632

004625a

DIMENSIONS – HSB-21 BASE 1 15/16 IN. (49 mm)

9/16 IN. (14 mm)

TO 4 IN. (102 mm) SQUARE OUTLET BOX

Description The SLR-24 photoelectric smoke detector utilizes two bicolor LEDs for indication of status. In a normal standby condition the LEDs flash Green every 3 seconds. When the detector senses that its sensitivity has drifted outside the UL listed sensitivity window the LEDs will flash Red every 3 seconds. When the detector senses smoke and goes into alarm the status LEDs will latch on Red. The detector utilizes an infrared LED light source and silicon photo diode receiving element in the smoke chamber. In a normal standby condition, the receiving element receives no light from the pulsing LED light source. In the event of a fire, smoke enters the detector smoke chamber and light is reflected from the smoke particles to the receiving element. The light received is converted into an electronic signal. Signals are processed and compared to a reference level, and when two consecutive signals exceeding the reference level are received within a specified period of time, the time delay circuit triggers the SCR switch to activate the alarm signal. The status LEDs light continuously during the alarm period.

1 7/8 IN. (47 mm)

7/16 IN. (11 mm)

5 7/8 IN. (149 mm)

004624a

004631

TO 3 IN. (76 mm) OR 4 IN. (102 mm) OCTAGON OUTLET BOX

DIMENSIONS – HSC-224RA BASE 2 1/2 IN. (63 mm)

1 1/8 IN. (29 mm)

TO 4 IN. (102 mm) SQUARE OR 4 IN. (102 mm) OCTAGON OUTLET BOX

5 7/8 IN. (149 mm)

004626a

004633

3-50

Technical Information Detector Base/Control Unit Compatibility Detector Base (Part No.)

AUTOPULSE ________________ IQ-318, IQ-636X-2 FZM-1

NS6-224 (427598)

Yes

HSB-21 (417457)

No

NS4-224 (427599)

Yes

HSC-224RA (416849)

No

Rated Voltage: . . . . . . . . . . . . . . . . . . . . . . . 17.7 to 33.0 VDC Working Voltage:. . . . . . . . . . . . . . . . . . . . . . . 15 to 33.0 VDC Surge Current: . . . . . . . . . . . . . . . . . . . . . . 160μA @ 24 VDC Normal Current: . . . . . . . . . . . . . . . . . . . . . . 45μA @ 24 VDC Alarm Current: . . . . . . . . . . . . . 150 mA maximum @ 24 VDC Ambient Temperature: . . . . +32 °F to +120 °F (0 °C to 49 °C) Humidity: . . . . . . . . . . . . . . . . . . . . . . . . . 95% R.H. maximum Color: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bone White Sensitivity Test Feature: . . . . . . Automatic sensitivity window verification test

Mounting Guidelines The detector bases are designed for surface mounting. The detector head can be inserted or removed from the base without disrupting the wiring connections. The following bases are compatible with the SLR-24 Photoelectric Detector: Base Type of Mounting Box HSB-21 4 in. (102 mm) Octagon, 4 in. (102 mm) Square NS4-224 3 in. (76 mm) Octagon NS6-224 4 in. (102 mm) Octagon, 4 in. (102 mm) Square HSC-224RA 4 in. (102 mm) Octagon, 4 in. (102 mm) Square HSC-224RA RELAY TERMINAL STRIP @@@@@@@@e? @@@@@@@@e?@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e? @@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ @@@@@@@@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@h? @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

ORANGE WIRE

C

1

VIOLET WIRE

NC

2

YELLOW WIRE

NO

3

GRAY WIRE

NO

4

GREEN WIRE

NC

5

C

6

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

WIRING DIAGRAM – TWO WIRE OPERATION NS4 AND NS6 SERIES BASE

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

BLUE WIRE

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@

@@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@ @@

TB1 CONNECTIONS

@@ @@ @@ @@ @@ @@ @@ @@

@@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@g ?@@ @@@@@@@@ @@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@?e@@@@@@@@e?@@@@@@@@ ?@@@@@@@@ ?@@@@@@@@

004629

RESISTOR SHOWN IS FOR EXAMPLE ONLY. NOT ALL ANNUNCIATORS HAVE IN-LINE RESISTANCE.

LISTED END OF LINE DEVICE

UL LISTED CONTROL POWER SUPPLY NEGATIVE 430 OHM RESISTOR

Listings and Approvals* UL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S1383 ULC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS463 California State Fire Marshal (CSFM). . . . . . . 7272-0410:107 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . 1O5A1.AY MEA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284-91-E * Listings and Approvals are under HOCHIKI AMERICA CORPORATION

IN4003 DIODE MUST BE INSTALLED IN SERIES WITH THE 430 OHM RESISTOR WHEN BASE IS USED TO OPERATE REMOTE LED.

ANNUNCIATION DEVICE MUST BE 4 CURRENT LIMITED TO 20 mA @ 24 VDC 3 MAXIMUM. NOT LIMITING CURRENT 5 COULD RESULT IN DAMAGE TO 6 004627 THE DETECTOR OR CAUSE A NOTE: WIRING TERMINALS FOR THE NS4 NO ALARM CONDITION. AND NS6 ARE IDENTICAL. BASES WITH THE “W” SUFFIX ARE WHITE IN COLOR.

WIRING DIAGRAM – HSB-21 AND HSC-224RA* STANDARD BASES, STYLE B EOL RESISTOR (+)

Ordering Information Part No.

Description


427596 427598 427599 417457 416849 415730 405491

SLR-24 Photoelectric Detector NS6-224 Base NS4-224 Base HSB-21 Base HSC-224RA Relay Base Test Magnet Punk Stick (Pack of 10)

1 0.5 0.5 0.5 0.5 0.5 0.5

(0.4) (0.2) (0.2) (0.2) (0.2) (0.2) (0.2)

S1

S1 L3 L4 S2 L2

L3 L4 S2 L2

(+)

(+)

(–) (–)

(–)

*REMOTE LED (16 mA MAX)

(–)

REMOTE LED

004628

SYSTEM COMMON (DC RETURN) * Do not wire HSC-224RA to remote LED as shown. Annunciation for the relay base (HSC-224RA) must be wired to the relay s using external power.








CAB-4 Cabinets (IQ-636X-2) General All cabinets for the AUTOPULSE IQ-636X-2 fire alarm control are fabricated from 16-gauge steel. The cabinet assembly consists of two basic parts: a backbox and a locking door. Cabinets are red with LEXAN® windows. • The key-locked door is provided with a pin-type hinge, two keys and the necessary hardware to mount the door to the backbox.

Agency Listings and Approvals UL Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 U.S. Coast Guard . . . . . . . . . . . . . . . . . . . . . . . . 161.002/42/1 ULC Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635/CS118 FM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approved California State Fire Marshal. . . . . . . . . . . . . . 7165-0028:214 7170-0028:216 MEA (NYC). . . . . . . . . . . . . . 17-96-E Vol. VI; 128-07-E Vol. 5

• The backbox has been engineered to provide ease-ofentry for the installer. Knockouts are positioned at numerous points to aid the installer in bringing a conduit into the enclosure. • Right- or left-hand hinges, selectable in the field. Door opens 180°. • Cabinets are arranged in four sizes, A (one tier) through D (four tiers). • A trim ring option is available for semi-flush mounting.

DIMENSIONAL DRAWINGS OF ‘B,’ “C,’ AND ‘D’ SIZED CABINETS ARE PROVIDED ON PAGE 2

007290

3-52

007291

Ordering Information A complete cabinet assembly consists of: a door, a backbox, an optional battery plate, and an optional semi-flush trim ring. For each cabinet required, order one “DR” door and one “SBB” backbox. The BP-4 battery plate is required for each cabinet assembly that mounts batteries and/or a power supply in the lower position of the cabinet. The optional trim ring is an attractive “picture frame”-style black metal ring. 007292

One Tier, “A” Size: Part No. 435598 DR-A4R: Door assembly, LEXAN window, one tier, RED. (ULC Part No. 437039) Part No. 433526 SBB-A4R: Backbox assembly, one tier, RED. (ULC Part No. 437043) Part No. 433534 TR-A4: Accessory semi-flush-mount trim ring, one tier (opening 24.062 in. (611 mm) W x 20.062 in. (510 mm) H), BLACK. Note: Black trim rings are used with red cabinets. (ULC Part No. 437047) Part No. 432795 BP-4: Battery . Used to cover battery and power supply when lower position is used in backbox. Two Tiers, “B” Size: Part No. 435599 DR-B4R: Door assembly, LEXAN window, two tiers, RED. (ULC Part No. 437040) Part No. 433527 SBB-B4R: Backbox assembly, two tiers, RED. (ULC Part No. 437044) Part No. 433535 TR-B4: Accessory semi-flush-mount trim ring, two tiers (opening 24.062 in. (611 mm) W x 28.562 in. (725 mm) H), BLACK. Note: Black trim rings are used with red cabinets. (ULC Part No. 437048) Part No. 432795 BP-4: Battery . Used to cover battery and power supply when lower position is used in backbox. Three Tiers, “C” Size: Part No. 435600 DR-C4R: Door assembly, LEXAN window, three tiers, RED. (ULC Part No. 437041) Part No. 433529 SBB-C4R: Backbox assembly, three tiers, RED. (ULC Part No. 437045) Part No. 433589 TR-C4: Accessory semi-flush-mount trim ring, three tiers (opening 24.062 in. (611 mm) W x 37.187 in. (945 mm) H), BLACK. Note: Black trim rings are used with red cabinets. (ULC Part No. 437049) Part No. 432795 BP-4: Battery . Used to cover battery and power supply when lower position is used in backbox.

THE BP-4 BATTERY DRESS COVERS THE MAIN POWER SUPPLY AND THE BATTERIES IN THE CABINET. ONLY ONE BP-4 IS REQUIRED PER CABINET.

Four Tiers, “D” Size: Part No. 435601 DR-D4R: Door assembly, LEXAN window, four tiers, RED. (ULC Part No. 437042) Part No. 433532 SBB-D4R: Backbox assembly, four tiers, RED. (ULC Part No. 437046) Part No. 433590 TR-D4: Accessory semi-flush-mount trim ring, four tiers (opening 24.062 in. (611 mm) W x 45.812 in. (1164 mm) H), BLACK. Note: Black trim rings are used with red cabinets. (ULC Part No. 437050) Part No. 432795 BP-4: Battery . Used to cover battery and power supply when lower position is used in backbox. Accessories: Part No. 433521 DP-1B: Blank dress , covers one CAB-4 tier, BLACK. (ULC Part No. 437058) Agency Listings and Approvals See the first page of this data sheet for listing agencies and file numbers. These listings and approvals apply to the CAB-4 Series Cabinets. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status.

LEXAN® is a ed trademark of GE Plastics, a subsidiary of General Electric Company.




LEM-320 Loop Expander Module (IQ-636X-2) General The LEM-320 module is used to expand the AUTOPULSE IQ-636X-2 to a second signaling line circuit (SLC) loop. Features • Up to 12,500 ft (3,810 m) on a Class B (Style 4) SLC loop (twisted unshielded) • Built-in degraded mode increases survivability • Very simple installation — plug-in style Specifications • Voltage: 24 VDC nominal, 27.6 VDC maximum • Maximum loop length: The maximum wiring distance of an SLC using 12 AWG (3.1 mm2) twisted-pair wire is 12,500 ft (3810 m) per channel. For a twisted unshielded pair, 12 AWG (3.1 mm2) to 18 AWG (0.78 mm2). Distance with 12 AWG: 12,500 ft (3,810 m) Distance with 14 AWG: 8,000 ft (2,438 m) Distance with 16 AWG: 4,875 ft (1,486 m) Distance with 18 AWG: 3,225 ft (983 m) 50 ohms maximum per length of Style 6 and 7 loops 50 ohms maximum per branch for Style 4 loop • Maximum current: for LEM-320: 100 mA; for single SLC loop: 400 mA maximum* *Note: Maximum short circuit — circuit will shut down until short-circuit condition is corrected. • Maximum resistance: 50 ohms (supervised and powerlimited) • Temperature and humidity ranges: This system meets NFPA requirements for operation at 32 °F to 120 °F (0 °C to 49 °C); and at a relative humidity (noncondensing) of 85% at 86 °F (30 °C) per NFPA, and 93% ± 2% at 89.6 °F ± 1.1 °F (32 °C ± 2 °C) per ULC. However, the useful life of the system’s standby batteries and the electronic components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that this system and all peripherals be installed in an environment with a nominal room temperature of 60 °F to 80 °F (15 °C to 27 °C).

007219

Listings and Approvals UL Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC Listed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635/CS118 California State Fire Marshal. . . . . . . . . . . . . . . 7170-0028.26 FM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Approved MEA (NYC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 128-07-E Vol. 5 City of Denver Hong Kong Product Line Information LEM-320 Loop Expander Module. Expands AUTOPULSE IQ-636X-2 to two loops.

3-53

Installation Mount LEM-320 module within the cabinet with the U; standard mounting locations are adjacent to the or in the row immediately below it. See installation manuals for instructions on installing modules and/or option boards in the chassis. After the LEM-320 module is mounted in the cabinet, connect the SLC loop to TB1. Up to 159 detectors and 159 modules can be connected to the SLC loop. FlashScan® devices can operate in either FlashScan or CLIP mode, but CLIP devices in CLIP mode must be set to address 99 or lower.

SLC LOOP CONNECTION TB1

GROUND FAULT LED

J1 – CONNECTS TO J3 ON IQ-636X U BOARD

007220

LEM-320 LOOP EXPANDER MODULE

Ordering Information Part No. Description ____ _________ 433508 LEM-320 Loop Expander Module 437062 LEM-320 Loop Expander Module (ULC)

Shipping Weight lb (kg) ___________ 1 (0.45) 1

(0.45)




Detection and Control Components New Series Photoelectric and Photoelectric/ Thermal Smoke Detectors (542R/542D) Features • Plug-in detector line – mounting base included. • Large wire-entry port. • In-line terminals with SEMS screws. • Mounts to octagonal and single-gang backboxes, 4 in. (102 mm) square backboxes, or directly to ceiling. • Stop-Drop ‘N Lock™ attachment to base. • Removable detector cover and chamber for easy cleaning. • Built-in remote maintenance signaling. • Drift compensation and smoothing algorithms. • Simplified sensitivity measurement.

008037

• Wide-angle, dual-color LED indication.

Physical Specifications

• Loop testing via “EZ Walk” feature.

Operating Temperature Range: For models 2W-B and 4WB: 32 °F to 120 °F (0 °C to 49 °C); for thermal models 2WT-B and 4WT-B: 32 °F to 100 °F (0 °C to 38 °C).

• Built-in test switch. Description New Series photoelectric and photoelectric/ thermal smoke detectors represent a significant advancement in conventional detection, incorporating three key features: installation ease, intelligence, and instant inspection. Installation ease: The New Series redefines installation ease with its plug-in design. This allows an installer to pre-wire the bases included with the heads. The large wire-entry port and in-line terminals provide ample room for neatly routing the wiring inside the base. The base accommodates a variety of backbox mounting methods, as well as direct mounting with drywall anchors. To complete the installation, New Series heads plug into the base with a simple Stop-Drop ’N Lock action. Intelligence: New Series detectors offer a number of intelligent features to simplify testing and maintenance. Drift compensation and smoothing algorithms, to minimize nuisance alarms, are standard in the New Series. When connected to an AUTOPULSE 542R/542D Control , two-wire New Series detectors are capable of generating a remote maintenance signal when they need cleaning. This signal is indicated by LEDs located at the AUTOPULSE 542R/542D Control .

Storage Temperature Range: –4 °F to +158 °F (–20 °C to +70 °C). Operating Humidity Range: 10% – 95% RH, non-condensing. Thermal Sensor: 135 °F (57 °C) fixed (models 2WT-B, 4WT-B). Freeze Trouble: 41 °F (5 °C) (models 2WT-B and 4WT-B). Sensitivity: 2.5%/ft (0.762%/meter) nominal. Input Terminals: Utilize 14 to 22 AWG wire. Dimensions (including base): 5.3 in. (135 mm) diameter, 2.0 in. (51 mm) high. Weight: 6.3 oz (178.6 grams). Mounting Options: 3.5 in. (89 mm) octagonal backbox; 4 in. (102 mm) octagonal backbox; single-gang backbox; 4 in. (102 mm) square backbox with a plaster ring; or direct mount to ceiling.

Instant inspection: The New Series provides wide-angle red and green LED indicators for instant inspection of detector condition. The LEDs indicate: normal standby, out-of-sensitivity, alarm, or freeze trouble conditions. The “EZ Walk” loop test feature is available on two-wire New Series detectors when connected to an AUTOPULSE 542R/542D Control . The “EZ Walk” feature verifies the initiating loop wiring by providing LED status indication at each detector.

3-54

Electrical Specifications

LED Modes

Green LED

Red LED

Power Up

Blink every 10 seconds


Normal (Standby)


OFF

Out of Sensitivity

OFF


Freeze Trouble

OFF


Maximum Initial Start-Up Time: For two-wire models: 45 seconds; for four-wire models: 15 seconds.

Alarm

OFF

Solid ON

Maximum Alarm Current: For two-wire models: 130 mA limited by control ; For four-wire models: 20 mA @ 12 V, 23 mA @ 24 V.

Condition

Duration

Initial LED Status Indication

80 Seconds

Initial LED Status Indication (if excessive electrical noise is present)

4 Minutes

Operating Voltage: 12/24 V non-polarized nominal; 8.5 V minimum; 35 V maximum. Maximum Ripple Voltage: 30% of nominal (peak to peak). Standby Current: 50 μA maximum average. Peak standby current: for two-wire models: 100 μA; not applicable for fourwire models. Maximum Start-Up Capacitance: For two-wire models: 0.1 μF; not applicable for four-wire models. Latching Alarm: Reset by momentary power interruption.

Alarm Ratings: For four-wire models: 0.5 A @ 30 VAC/VDC; not applicable for two-wire models. Alarm Reset Voltage: 2.5 V. Alarm Reset Time: 0.3 seconds. Wiring Diagrams

Power Up Sequence for LED Indication

Agency Listings and Approvals UL Listed . . . . . . . . . . . . . . . . . . . . . . . . S911 FM . . . . . . . . . . . . . . . . . . . . . . . . . Approved CSFM . . . . . . . . . . . . . . . . . . . . 7272-1653:152 MEA . . . . . . . . . . . . . . . . . . . . . . . . 290-01-E Maryland State Fire Marshal . . . . . . . . Permit No. 2093 ETL . . . . . . . . . . . . . . . . . . . . . . . . Approved USCG. . . . . . . . . . . . . . . . . . . . . 161.002/A42/1

ANN-BUS


AUX or SMOKE + POWER –

Part No. _______ 435893

Description _________ 2W-B: Two-Wire Photoelectric Smoke Detector

435894

2WT-B: Two-Wire Photoelectric Smoke Detector with 135 °F (57 °C) Fixed Thermal Sensor

1.5

(0.7)

435895

4W-B: Four-Wire Photoelectric Smoke Detector

1.5

(0.7)

435896

4WT-B: Four-Wire Photoelectric Smoke Detector with 135 °F (57 °C) Fixed Thermal Sensor

1.5

(0.7)

EOL RELAY EOLR-1

IDC +

–

EOL RESISTOR (5) COM (4) NO (3) – IN/OUT (2) + OUT (1) + IN

(5) COM (4) NO (3) – IN/OUT (2) + OUT (1) + IN

4-WIRE CONTROL

4W-B or 4WT-B DETECTOR

008038

Shipping Weight lb (kg) _________ 1.5 (0.7)

Stop-Drop ‘N Lock™ is a trademark of Honeywell International Inc. TYCO FIRE PROTECTION PRODUCTS ONE STANTON STREET MARINETTE, WI 54143-2542 715-735-7411



2151 Photoelectric Smoke Detector (542R/542D) Features • Unique optical sensing chamber • Built-in signal processing • 3.0% nominal sensitivity • Removable cover for field cleaning • Visible LED “blinks” in standby • Sealed against dirt, insects, and back pressure • Field metering of detector sensitivity • Built-in magnetic test switch • Low standby current • Built-in tamper-resistant feature • Designed for direct surface or electrical box mounting • 360° Field viewing angle of the visual alarm LEDs • Insect-resistant screening • Easy plug-in of the head to base • SEMS screws for easy wiring • Air velocity up to 3000 feet per minute (914 meters per minute)

Technical Information Stand-by Current: . . . . . . . . . . . . . . . . . . . . . . . 85 microamps Sensitivity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0% nominal Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 lb (277 g) Size:. . . . . . . . . . . . . . . . . . . . . . 1.7 in. high x 4.0 in. diameter (84 mm x 102 mm) Construction:. . . . . . . . . Flame retardant white thermo plastic Temperature: . . . . . . . . . . . . . 32 °F to 120 °F (0 °C to 49 °C) Humidity Range: . . . . . . . . . . . 10-93% RH (non-condensing) Maximum Air Velocity: . . . . . . . . . . . . . . . . 3000 ft per minute (15 m per second)

2151 PHOTOELECTRIC SMOKE DETECTOR WITH BASE

Applications Photoelectric detectors are recommended in areas where slow smoldering fires are likely to ignite. In areas where small combustion particles are usually present from fork-lift trucks, cooking stoves, etc., they are less likely than ionization detectors to produce false alarms. The detectors are used in combination with an AUTOPULSE Control System and an fire suppression system for automatic detection, alarm, equipment control, and fire suppression system release capabilities. Description The 2151 photoelectric smoke detector contains a unique optical sensing chamber designed to sense the presence of smoke particles produced by a wide range of combustion sources and meet the performance criteria designed by UL 268. An integrated circuit incorporates signal processing to reduce false alarms and sample/hold circuitry to provide easy field metering of sensitivity. The 2151 photoelectric detector incorporates the light scatter principle within its sensing chamber and solid-state circuitry allowing it to react to either smoldering or flaming fires. The high-impedance circuitry of the detector allows a single loop to power multiple detectors with very low power consumption. Two externally-mounted LED indicators are provided which will blink as long as the detector is powered and will light steadily when the detector is in alarm.

007353

B110LP OPTIONAL NFPA CLASS “A” WIRING (–)

(–)

2

(–)

(–)

1 (+)

4 (+)

3

2

(–)

3 1 (+)

4 (+)

(+) (+) 007350

3-55

Technical Information (Continued) Base Model

Loop Type

Current Limit Resistor

Type

Standby Voltage

Current Draw on Alarm

B110LP B401 B401B B401BR-750 B402B

2-Wire 2-Wire 2-Wire 2-Wire 2/4 Wire

No No No Yes Yes

—— —— —— —— Form A/C

12-24 VDC 12-24 VDC 8.5-35 VDC 17-32 VDC 17-32 VDC

10-100 mA* 10-100 mA* 10-100 mA* 10-39 mA 14-39 mA

* Limited by control unit

Detector Base/Control Unit Compatibility Detector Base (Part No.)

AUTOPULSE 542R, 542D

AUTOPULSE IQ-318, IQ-636X-2 FZM-1

B110LP (430025) B401 (423026) B401B (417996) B401BR-750 (78997) B402B (79011)

Yes Yes Yes No 4-wire only

Yes Yes Yes No 4-wire only

B110LP BASE WIRING DIAGRAM (–)

(–) (–)

2 1 (+)

EOL RESISTOR

(–)

3

4 (+)

(+)

2

(–)

1 (+)

3

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S911 California State Fire Marshal (CSFM). . . . . . . 7271-1209:159 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . Approved MEA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205-94-E * Listings and Approvals are under SYSTEM SENSOR

4 (+)

Ordering Information Part No.

Description


430023

2151, Photoelectric Detector

1

(0.4)

430025

B110LP Standard Base

0.5

(0.2)

430026

B401 4 in. Dia Base

0.5

(0.2)

428138

F110 Trim Ring, Low Profile

0.5

(0.2)

417675

M02-04 Test Magnet

0.5

(0.2)

417699

EOL, Power Supervision Relay

1

(0.4)

(+) 007351

Mounting Guidelines The detector bases are designed for surface mounting. The detector head can be inserted or removed from the base without disrupting the wiring connections. All detector bases can be mounted to a 3 1/2 in. (89 mm) octagon, 4 in. (102 mm) octagon, or a 4 in. (102 mm) square outlet box.



Detection and Control Components ANN-80 80 Character LCD Serial Annunciator (542R/542D) Features • Backlit 80-character LCD display (20 characters x 4 lines) • Mimics all display information from the host . • Control switches for System Acknowledge, Signal Silence, Drill, and Reset. • Control switches can be independently enabled or disabled at the AUTOPULSE 542R/542D Control . • Keyswitch enables/disables control switches and mechanically locks annunciator enclosure • Keyswitch can be enabled or disabled at the AUTOPULSE 542R/542D Control . • Enclosure supervised for tamper. • System status LEDs for AC Power, Alarm, Trouble, Supervisory, and Alarm Silence. • Local sounder can be enabled or disabled at the AUTOPULSE 542R/542D Control . • ANN-80 connects to the ANN-BUS terminal on the AUTOPULSE 542R/542D Control and requires minimal programming. • Displays device type identifiers, individual point alarm, trouble, supervisory, zone, and custom alpha labels. • Time-and date display field. • Aesthetically pleasing design constructed of durable Lexan. • Surface mount directly to wall or to single, double, or 4 in. (102 mm) square electrical box. • Semi-flush mount to single, double, or 4 in. (102 mm) square electrical box. • Can be remotely located up to 6,000 ft (1,800 m) from the . • Backlight turns off during AC loss to conserve battery power but will turn back on if an alarm condition occurs. • May be powered by 24 VDC from the host AUTOPULSE 542R/542D Control or by remote power supply (requires 24 VDC). • Up to eight (8) ANN-80s can be connected on the ANNBUS.

008031

Description The ANN-80 Annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the AUTOPULSE 542R/542D Control display. It provides system status indicators for AC Power, Alarm, Trouble, Supervisory, and Alarm Silenced conditions. The ANN-80 and the AUTOPULSE 542R/542D Control communicate over a two-wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host AUTOPULSE 542R/542D Control or a remote UL-listed, filtered power supply. The ANN-80 displays English-language text of system point information including device type, zone, trouble or supervisory status, as well as any custom alpha labels programmed into the control . It includes control switches for remote control of critical system functions. (A keyswitch prevents unauthorized operation of the control switches). Up to eight (8) ANN-80s may be connected to the ANN-BUS of the AUTOPULSE 542R/542D Control . Minimal programming is required, which saves time during system commissioning. The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the ANN-BUS power requirements. See the AUTOPULSE 542R/542D manual for more information. Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the AUTOPULSE 542R/542D Control . A maximum of eight (8) devices can be connected to the AUTOPULSE 542R/542D Control ANN-BUS communication circuit. See the AUTOPULSE 542R/542D manual for more information. Controls and Indicators • AC Power • Alarm • Trouble • Supervisory • Alarm Silenced

3-56

Specifications

ANN-80 Wiring to AUTOPULSE 542R/542D CONTROL

• Operating voltage range: 18 VDC to 28 VDC

AUTOPULSE 542R/542D CONTROL

• Current consumption @ 24 VDC nominal (filtered and non-resettable): 40 mA maximum.

(-) (+) A B

TB3

• Ambient temperature: 32 °F to 120 °F (0 °C to 49 °C).

4 3 2 1

• Relative humidity: 93% ± 2% RH (non-condensing) at 90 °F ± 3 °F (32 °C ± 2 °C). ANN-BUS AND POWER WIRING ARE SUPERVISED AND POWER-LIMITED

• 5 3/8 in. (137 mm) high x 6 7/8 in. (175 mm) wide x 1 3/8 in. (35 mm) deep • For use indoors in a dry location. • All connections are power-limited and supervised.

B A (+) (-)

TB1

ANN-80

Wiring Requirements

008032

The ANN-80 connects to the AUTOPULSE 542R/542D Control ANN-BUS communications circuit. To determine the type of wire and the maximum wiring distance that can be used with AUTOPULSE 542R/542D Control ANN-BUS accessory modules, it is necessary to calculate the total worst case current draw for all modules on a single 4conductor bus. The total worst case current draw is calculated by adding the individual worst case currents for each module.

Agency Listings and Approvals UL . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 FM . . . . . . . . . . . . . . . . . . . . . . . . . Approved CSFM . . . . . . . . . . . . . . . . . . . . 7165-0595:118

Note: For total worst case current draw on a single ANN-BUS, refer to the AUTOPULSE 542R/542D manual.


After calculating the total worst case current draw, the table below specifies the maximum distance the modules can be located from the AUTOPULSE 542R/542D Control on a single wire run. The table ensures 6.0 volts of line drop maximum. In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor.

Part No. _______ 435355

Description _________ ANN-80 80 Character LCD Serial Annunciator

Shipping Weight lb (kg) __________ 3 (1.4)

These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 ft (1,800 m), regardless of gauge used. See table below. A 14 to 18 AWG (0.75 – 2.08 mm2) wire for 24 VDC power circuit is acceptable. All connections must be power-limited and supervised. A maximum of eight (8) ANN-80 modules may be connected to this circuit. Communication Pair Wiring Distance: AUTOPULSE 542R/542D Control to Last ANN-BUS Module Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100

1,852 ft

(565 m)

4,688 ft (1,429 m)

*6,000 ft

(1,829 m)

*6,000 ft (1.829 m)

0.200

926 ft

(282 m)

2,344 ft

(715 m)

3,731 ft

(1,137 m)

5,906 ft (1,800 m)

0.300

617 ft

(188 m)

1,563 ft

(476 m)

2,488 ft

(758 m)

3,937 ft (1200 m)

0.400

463 ft

(141 m)

1,172 ft

(357 m)

1,866 ft

(569 m)

2,953 ft

(900 m)

0.500

370 ft

(113 m)

938 ft

(286 m)

1,493 ft

(455 m)

2,362 ft

(720 m)

0.600

309 ft

(94 m)

781 ft

(238 m)

1,244 ft

(379 m)

1,969 ft

(600 m)

0.700

265 ft

(81 m)

670 ft

(204 m)

1,066 ft

(325 m)

1,687 ft

(514 m)

0.800

231 ft

(70 m)

586 ft

(179 m)

933 ft

(284 m)

1,476 ft

(450 m)

0.900

206 ft

(63 m)

521 ft

(159 m)

829 ft

(253 m)

1,312 ft

(400 m)

1.000 (max.)

185 ft

(56 m)

469 ft

(143 m)

746 ft

(227 m)

1,181 ft

(360 m)



Detection and Control Components ANN-LED Annunciator Module (542R/542D) Features • Listed to UL Standard 864, 9th Edition. • ANN-LED connects to the ANN-BUS terminal on the AUTOPULSE 542R/542D Control and requires minimal programming. • Mounts in the DP-51050LED Dress or in a separate enclosure. • Provides three (3) LEDs for each zone: Alarm, Trouble and Supervisory. • Can be remotely located up to 6,000 ft (1,829 m) from the . • May be powered by 24 VDC from the host AUTOPULSE 542R/542D Control or by remote power supply (requires 24 VDC). • Up to eight (8) ANN-BUS devices may be connected to the ANN-BUS of the AUTOPULSE 542R/542D Control . Description The ANN-LED annunciator module provides LED annunciation of general system faults and input zones/points when used with a compatible AUTOPULSE 542R/542D Control . The ANN-LED module provides alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten (10) input zones or addressable points. The ANN-LED is supplied standard with certain Canadian FAs as required by ULC. The ANN-LED and the AUTOPULSE 542R/542D Control communicate over a two-wire serial interface employing the ANN-BUS communication format. An additional two wires are used for 24-volt DC power. A single four-conductor unshielded cable may be used for both power and data communications. Up to eight (8) ANN-BUS devices may be connected to the ANN-BUS of the AUTOPULSE 542R/542D Control .

008035

• Relative Humidity: 93% ± 2% RH (non-condensing) at 90 ºF ± 3 ºF (32 ºC ± 2 ºC) • For use indoors in a dry location Wire Requirements The ANN-LED connects to the AUTOPULSE 542R/542D Control ANN-BUS communications circuit. To determine the type of wire and the maximum wiring distance, calculate the total worst case current draw for all modules on a single 4-conductor bus. Use the table on the following page to determine the maximum distance the modules can be located from the AUTOPULSE 542R/542D Control . In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 ft (1,800 m), regardless of gauge used. Note: Refer to the AUTOPULSE 542R/542D manual for wiring details and printer settings. ANN-LED Connection to AUTOPULSE 542R/542D Control

ANN-BUS devices can be powered by an auxiliary power supply when available power is exceeded. See the AUTOPULSE 542R/542D manual for information. Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the AUTOPULSE 542R/542D Control . A maximum of eight (8) devices can be connected to the AUTOPULSE 542R/542D Control ANN-BUS communication circuit. See the AUTOPULSE 542R/542D manual for more information. Specifications • Maximum ANN-BUS Voltage: 24 VDC

AUTOPULSE 542R/542D CONTROL ANN-LED

• Maximum Current: Alarm: 68 mA Standby: 28 mA • Maximum wiring distance from AUTOPULSE 542R/542D Control : 6,000 ft (1,829 m) • Ambient Temperature: 32 ºF to 120 ºF (0 ºC to 49 ºC)

–24 VDC +24 VDC ANN-BUS 008036

3-56.1

Agency Listings and Approvals UL . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 CSFM . . . . . . . . . . . . . . . . . . . . 7165-0595:118 MEA . . . . . . . . . . . . . . . . . . . . . . . . 333-07-E

Ordering Information The ANN-LED module provides alarm (red), trouble (yellow) and supervisory (yellow) indication for up to ten (10) input zones or addressable points. Shipping Weight Part No. Description lb (kg) _______ _________ __________ 435359 ANN-LED Annunciator Module 3 (1.4)

Communication Pair Wiring Distance: AUTOPULSE 542R/542D Control to Last ANN-BUS Module Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100

1,852 ft

(565 m)

4,688 ft (1,429 m)

*6,000 ft

(1,829 m)

*6,000 ft (1.829 m)

0.200

926 ft

(282 m)

2,344 ft

(715 m)

3,731 ft

(1,137 m)

5,906 ft (1,800 m)

0.300

617 ft

(188 m)

1,563 ft

(476 m)

2,488 ft

(758 m)

3,937 ft (1200 m)

0.400

463 ft

(141 m)

1,172 ft

(357 m)

1,866 ft

(569 m)

2,953 ft

(900 m)

0.500

370 ft

(113 m)

938 ft

(286 m)

1,493 ft

(455 m)

2,362 ft

(720 m)

0.600

309 ft

(94 m)

781 ft

(238 m)

1,244 ft

(379 m)

1,969 ft

(600 m)

0.700

265 ft

(81 m)

670 ft

(204 m)

1,066 ft

(325 m)

1,687 ft

(514 m)

0.800

231 ft

(70 m)

586 ft

(179 m)

933 ft

(284 m)

1,476 ft

(450 m)

0.900

206 ft

(63 m)

521 ft

(159 m)

829 ft

(253 m)

1,312 ft

(400 m)

1.000 (max.)

185 ft

(56 m)

469 ft

(143 m)

746 ft

(227 m)

1,181 ft

(360 m)



Detection and Control Components ANN-RLY Relay Module (542R/542D) Features • ANN-RLY connects to the ANN-BUS terminal on the AUTOPULSE 542R/542D Control and requires minimal programming. • Provides ten (10) programmable Form-C relays. • Ten (10) Form-C relays can be programmed for various functions; Alarm, Trouble, Supervisory, AC Loss, Waterflow Delay, Input Zones and Silenceable Alarm. • May be powered by 24 VDC from the host AUTOPULSE 542R/542D Control or by remote power supply (requires 24 VDC). • Up to eight (8) ANN-BUS devices may be connected to the ANN-BUS of the AUTOPULSE 542R/542D Control .

008033

• Listed to UL Standard 864, 9th Edition.

• Connections to AUTOPULSE 542R/542D Control are power-limited and supervised.

Description

• Relay Ratings: 2 Amps @ 30VDC (Resistive) 0.5 Amps @ 30VAC (Resistive)

The ANN-RLY relay module provides ten (10) programmable Form-C relays when used with a compatible AUTOPULSE 542R/542D Control . The ANN-RLY module may be mounted inside the AUTOPULSE 542R/542D Control main circuit board chassis or in the battery area of the enclosure using optional mounting bracket Part No. 435897. Reference Installation Instructions in the AUTOPULSE 542R/542D manual. The ANN-RLY and the AUTOPULSE 542R/542D Control communicate over a two-wire serial interface employing the ANN-BUS communication format. An additional two wires are used for 24-volt DC power. A single four-conductor unshielded cable may be used for both power and data communications. Up to eight (8) ANN-BUS devices may be connected to the ANN-BUS of the AUTOPULSE 542R/542D Control . ANN-BUS devices can be powered by an auxiliary power supply when available power is exceeded. See the AUTOPULSE 542R/542D manual for information.

Wire Requirements The ANN-RLY connects to the AUTOPULSE 542R/542D Control ANN-BUS communications circuit. To determine the type of wire and the maximum wiring distance, calculate the total worst case current draw for all modules on a single 4-conductor bus. Use the table on the following page to determine the maximum distance the modules can be located from the AUTOPULSE 542R/542D Control . In general, the wire length is limited by resistance, but for heavier wire gauges, capacitance is the limiting factor. These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 ft (1,800 m), regardless of gauge used. Note: Refer to the AUTOPULSE 542R/542D manual for wiring details. ANN-RLY Wiring to AUTOPULSE 542R/542D Control

Each ANN-BUS device requires a unique address (ID Number) in order to communicate with the AUTOPULSE 542R/542D Control . A maximum of eight (8) devices can be connected to the AUTOPULSE 542R/542D Control ANN-BUS communication circuit. See the AUTOPULSE 542R/542D manual for more information. Specifications • Maximum ANN-BUS Voltage: 24 VDC • Maximum Current: – Alarm: 75 mA Standby: 15 mA • Ambient Temperature: 32 ºF to 120 ºF (0 ºC to 49 ºC) • Relative Humidity: 93% ± 2% RH (non-condensing) at 90 ºF ± 3 ºF (32 ºC ± 2 ºC) • For use indoors in a dry location

AUTOPULSE 542R/542D CONTROL ANN-RLY

–24 VDC +24 VDC ANN-BUS 008034

3-56.2

Agency Listings and Approvals UL . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 CSFM . . . . . . . . . . . . . . . . . . . . 7165-0595:118 MEA . . . . . . . . . . . . . . . . . . . . . . . . 333-07-E

Ordering Information • ANN-RLY Relay Module provides ten (10) programmable Form C relays. • ANN-MBRLY Optional mounting bracket.

Part No. _______ 435358 437021 435897

Description _________ ANN-RLY Relay Module ANN-RLY Relay Module (ULC) ANN-MBRLY Mounting Bracket

Shipping Weight lb (kg) __________ 1 1 1

(0.5) (0.5) (0.5)

Communication Pair Wiring Distance: AUTOPULSE 542R/542D Control to Last ANN-BUS Module Total Worst Case Current Draw (amps) 22 Gauge 18 Gauge 16 Gauge 14 Gauge 0.100

1,852 ft

(565 m)

4,688 ft (1,429 m)

*6,000 ft

(1,829 m)

*6,000 ft (1.829 m)

0.200

926 ft

(282 m)

2,344 ft

(715 m)

3,731 ft

(1,137 m)

5,906 ft (1,800 m)

0.300

617 ft

(188 m)

1,563 ft

(476 m)

2,488 ft

(758 m)

3,937 ft (1200 m)

0.400

463 ft

(141 m)

1,172 ft

(357 m)

1,866 ft

(569 m)

2,953 ft

(900 m)

0.500

370 ft

(113 m)

938 ft

(286 m)

1,493 ft

(455 m)

2,362 ft

(720 m)

0.600

309 ft

(94 m)

781 ft

(238 m)

1,244 ft

(379 m)

1,969 ft

(600 m)

0.700

265 ft

(81 m)

670 ft

(204 m)

1,066 ft

(325 m)

1,687 ft

(514 m)

0.800

231 ft

(70 m)

586 ft

(179 m)

933 ft

(284 m)

1,476 ft

(450 m)

0.900

206 ft

(63 m)

521 ft

(159 m)

829 ft

(253 m)

1,312 ft

(400 m)

1.000 (max.)

185 ft

(56 m)

469 ft

(143 m)

746 ft

(227 m)

1,181 ft

(360 m)



Detection and Control Components 4XTM Transmitter Module (542R/542D) Description The 4XTM Transmitter Module is an option for the AUTOPULSE control systems. The module provides a supervised output for local energy municipal box transmitter (for NFPA 72 Auxiliary Protective Signaling System) and alarm and trouble reverse polarity circuits (for NFPA 72 Remote Station Protective Signaling System). Also included is a DISABLE switch and disable trouble LED. A jumper option allows the reverse polarity circuit to open with a System Trouble condition if no alarm condition exists. Technical Information For Local Energy Municipal Box service (NFPA 72 Auxiliary Protective Signaling System): Supervisory Current . . . . . . . . . . . . . . . . 5.0 mA Trip Current . . . . 0.35 amps (subtracted from indicating appliance power) Coil Voltage . . . . . . . . . . . . . . . . . . . 3.65 VDC Coil Resistance . . . . . . . . . . . . . . . . 14.6 ohms Total wire resistance between unit and trip coil . . 3 ohms For Remote Station service (NFPA 72 Remote Station Protective Signaling System): Maximum Load for each circuit. . . . . . . . . . . 10 mA Reverse Polarity Output Voltage . . . . . . . . . 24 VDC

Listings and Approvals* UL . . . . . . . . . . . . . . . . . . . . . . . . . . . S635 ULC . . . . . . . . . . . . . . . . . . . . . CS118, CS733 Factory Mutual (FM) . . . . . . . . . . . . . . . . Approved MEA . . . . . . . . . . . . . . . . . . . . 104-93-E Vol. VI CSFM . . . . . . . . . . . . . . . . . . . . 7165-0028:245 * Listings and Approvals are under NOTIFIER


Part No.

Description


435602

4XTM Transmitter Module

1

(0.5)

4XTM TRANSMITTER MODULE (POLARITIES SHOWN IN ACTIVATED POSITIONS)

1 2 3 4 5 6

+ – + – + –

} } }

REMOTE ALARM REMOTE TROUBLE MUNICIPAL BOX

4 IN. (102 mm) TBL JUMPER DISCONNECT LED

2 1/2 IN. (64 mm) 007342

DISCONNECT SWITCH











Detection and Control Components LIFEalarm® Photoelectric Smoke Detectors with Smoke/Heat Detection (Z-10) Features LIFEalarm detection combines photoelectric detection with heat detection to provide a multi-mode detector with four detection mechanisms:* • Stable and reliable photoelectric smoke detection with built-in LIFEalarm sensitivity drift compensation • Resettable, thermistor-based fixed temperature detection • Resettable, thermistor-based rate-of-rise temperature detection • A built-in analysis of photoelectric and thermal activity trending that provides fire detection with higher accuracy than either detection means used separately

Functional chamber enclosure: • Louvered design enhances smoke capture by directing flow to chamber • Entrance areas are minimally visible when ceiling mounted Multi-function LED indicator: • Indicates normal and alarm conditions • Provides status during magnetic functional test Magnetically operated functional test: • Initiates alarm and verifies performance • Identifies general sensitivity status using detector LED pulses (normal, more sensitive, or less sensitive) • With detectors categorized as normal or needing cleaning or other service, maintenance priorities can be more easily determined Available base options: • Bases for 2-wire operation • Auxiliary alarm relay output • Remote alarm indicating LED output Optional remote LED alarm indicator Listings and Approvals • UL Listed: S6648 • ULC Listed: S6648 • FM Approved: 3015976

006622

Detector (Part No. 430560) Mounted in Base Description LIFEalarm photoelectric smoke detectors combine photoelectric smoke detection technology and quick response thermistor-based heat detection technology into a sophisticated, intelligent detector that analyzes each of these activities and their combination to determine whether alarm conditions are present. An onboard microprocessor provides four independent detection modes: photoelectric detection with sensitivity drift compensation, fixed temperature heat detection, rate-of-rise temperature heat detection, and photoelectric/heat trending analysis and alarm detection. If any of these alarm conditions are experienced, an alarm is initiated. Specifications Voltage

15 to 32 VDC, from Control IDC

Standby Current

100 µA @ 24 VDC

Alarm Current, 2-Wire Operation

Up to 86 mA maximum, exact current is determined by alarm current limiting of connected IDC (initiating current device)

Auxiliary Relay Ratings

Refer to page 3 under Product Selection

Rate-of-Rise Temperature Alarm*

≤ 20° F/min (11° C/min), only effective at temperatures above 90° F (32° C)

Fixed Temperature Alarm

135° F (57° C)

UL Listed Temp. Range*

32° F to 100° F (0° C to 38° C)

Operating Temp. Range

15° F to 100° F (-9° C to 38° C)

Smoke Obscuration Sensitivity

2.8%/ft Nominal, per UL268

UL Listed Temp. Range

32° to 100° F (0° to 38° C)

Operating Temp. Range

15° to 122° F (–9° to + 50° C)

Air Velocity Range

0-2000 ft/min (0-610 m/min)

Humidity Range

10% to 95% RH from 32° to 122° F (0° to 50° C)

Color

Frost White

Dimensions

4 7/8 in. Dia. x 2 in. H, mounted in base (124 mm x 51 mm)

• MEA (NYC): Approved • CSFM: Approved * LIFEalarm detectors are protected by one or more of the following U.S. Patents: 5,155,468; 5,173,683; 5,400,014; 5,543,777; 5,710,541; 5,818,326; 6,195,011; D383,407; D388,352; D392,573.

* Always locate this and all rate-of-rise heat detection devices away from extremes of temperature fluctuation.

3-60

Description (Continued)

Diagnostic Information

Intelligent Data Evaluation. Conventional smoke detectors will typically drift toward being too sensitive due to the accumulation of dust and dirt. With LIFEalarm analog detection, data from the photoelectric chamber is monitored and analyzed at the detector to provide a continuously shifting reference point.

Magnetic Test Information. Status information is available by performing the magnetic test and observing the detector LED pulses. The LED will normally go directly into alarm with the magnetic test. If there is an off-normal condition, the LED pulses first to indicate the condition and then goes into alarm.

Drift Compensation. The data evaluation and its shifting reference point provide a software filtering process that compensates for environmental factors (dust, dirt, etc.) and component aging, establishing an accurate reference for evaluating new activity. With this filtering, the resulting drift compensation provides a significant reduction in the probability of false or nuisance alarms caused by shifts in sensitivity – either up or down. Maintained Sensitivity and Dirty Status Indications. With its onboard software compensation, the detector maintains its sensitivity much longer in the presence of dust and dirt accumulation. Additionally, it will determine when the dirt accumulation is approaching the limit of compensation, and will indicate that condition via its status indicator LED (see diagnostic information). Electronic Heat Detection Fixed Temperature Heat Detection is provided with the addition of a fast response thermistor that causes an alarm at a fixed temperature of 135° F (57° C). Rate-of-Rise Heat Detection occurs at ≥20° F/min (11° C/min). To minimize the possibility of false alarms, rateof-rise detection is correlated to the ambient temperature and is only in effect above 90° F (32° C). DETECTOR BASE

DETECTOR, PART NO. 430560 (PART NO. 430696 ULC)

006622

STATUS INDICATOR LED

Smoke Detector Package

THERMISTOR GUARD

Application Notes Observe heat detector location guidelines. Ambient temperature operating range is 32° F to 100° F (0° C to 38° C). Temperature fluctuations should be below 6° F/min (3.3° C/min). Detector locations should be determined only after careful consideration of the physical layout and contents of the area to be protected.

Product Selection Smoke Detector Part No.

Description

Compatibility

430560

LIFEalarm photoelectric detector with photoelectric/thermal detection

Compatible with detector bases: Part Nos. 430567 and 430569

Part No.

Description

Details

430567

2-Wire Base with connections for Remote Alarm LED Indicator

• IDC and LED connections are screw terminals for in/out wiring, #18 to #14 AWG

430569

2-Wire Base with Auxiliary Alarm Relay and connections for Remote LED Indicator

Relay Ratings, Dual Form "C," For Suppressed Loads: • Power limited, 1 A @ 28 VDC • Non-power limited, 1/2 A @ 120 VAC Wiring Connections (In/Out where required): • Relay s and IDC (-), color coded #18 AWG leads • IDC (+) and LED wiring, screw terminals for #18 to #14 AWG

Detector Bases

Note: Must be connected as the only device on the IDC to ensure relay operation. Detector Accessories Part No.

Description

Details

430572

Remote LED Indicator

• Mounted on single gang stainless steel plate

Dimensions and Reference Information

ALARM

4 7/8 IN. (124 mm)

BASE HEIGHT 11/16 IN. (17 mm)

2 IN. (51 mm)

006567 006623

STATUS INDICATOR LED DETECTOR (PART NO. 430560) MOUNTED ON BASE

REMOTE RED LED INDICATOR (PART NO. 430572) (NOT TO SCALE)

Visible LED Status Indications LED Indication

Status

Flashes every 4 seconds

Circuit is Normal, power is applied

Steady On

Detector is in Alarm

LED Response to Magnetic Test * LED Indication

Alarm Response

Detector Status

Action Required

LED turns ON

Alarm is initiated

Normal, sensitivity is within compensation range

None

Flashes quickly, 6 times in 3 seconds, then turns ON

Alarm is initiated

More sensitive, out of normal compensation range

Cleaning or other service is required

Flashes slowly, 4 times in 8 seconds, then turns ON

Alarm is initiated

Less sensitive, out of normal compensation range

Alarm is NOT initiated

Detector is malfunctioning

Service is required

* Testing requires placing a magnet at the designated location on the detector cover for 4 seconds.

Mounting Information ELECTRICAL BOX REQUIREMENTS: WITHOUT RELAY (BASES, PART NO. 430567): 4 IN. (102 mm) OCTAGONAL OR 4 IN. (102 mm) SQUARE, 1 1/2 IN. (38 mm) DEEP SINGLE GANG, 2 IN. (51 mm) DEEP WITH RELAY (BASES, PART NO. 430569): 4 IN. (102 mm) OCTAGONAL, 1 1/2 IN. (38 mm) DEEP, WITH 1 1/2 IN. (38 mm) EXTENSION RING 4 IN. (102 mm) SQUARE, 1 1/2 IN. (38 mm) DEEP, WITH 1 1/2 IN. (38 mm) EXTENSION RING

SURFACE MOUNT REFERENCE

4 IN. SQUARE (102 mm) OCTAGONAL BOX

4 IN. SQUARE (102 mm) SQUARE BOX

1 1/2 IN. (38 mm) MINIMUM BOX DEPTH

FLUSH MOUNT REFERENCE, MOUNT EVEN WITH FINAL SURFACE, OR WITH UP TO 1/4 IN. (6 mm) MAXIMUM RECESS

PART NO. 430569 INCLUDES A RELAY MODULE THAT MOUNTS IN BASE ELECTRICAL BOX

SMOKE DETECTOR BASES

006624

SMOKE DETECTOR



Detection and Control Components LIFEalarm® Photoelectric Smoke Detectors For Two-Wire Bases (Z-10) Features LIFEalarm® Photoelectric smoke detector with on-board sensitivity drift compensation* Functional chamber enclosure: • Louvered design enhances smoke capture by directing flow to chamber • Entrance areas are minimally visible when ceiling mounted

006564

LIFEalarm Photoelectric Detector Mounted in Base

Multi-function indicator LED indicates normal and alarm conditions Magnetically operated functional test: • Initiates alarm and verifies performance • Identifies general sensitivity status using detector LED

Listings and Approvals • UL Listed: S6648 • ULC Listed: S6648 • FM Approved: 3015976

Models available in two sensitivity settings:

• CSFM: Approved

• Part No. 430559, Standard Sensitivity, nominal 2.8%/ft obscuration

• MEA (NYC): Approved

• Part No. 430562, Special Application Sensitivity, nominal 3.5%/ft obscuration

Specifications Voltage

15 to 32 VDC, from Control IDC

• Bases for 2-wire operation

Standby Current

100 μA @ 24 VDC

• Auxiliary alarm relay output


Up to 86 mA maximum, exact current is determined by alarm current limiting of connected IDC

Auxiliary Relay Ratings

Refer to page 2 under Product Selection

Air Velocity Range

0-2000 ft/min (0-610 m/min)

UL Listed Temp. Range

32° to 100 °F (0° to 38 °C)

Available base options:

Optional remote alarm indicating LED Description LIFEalarm photoelectric detectors provide many of the proven analog sensing features for applications where detectors are connected to conventional 2-wire initiating device circuits (IDCs). Each detector has an on-board microprocessor that evaluates its photoelectric light scattering chamber activity and makes an intelligent decision based on light obscuration history as to whether an alarm condition is present. LIFEalarm detectors are packaged in a patented housing that minimizes the visibility of the air intake louvers from the normal viewing locations while maintaining a high performance smoke capture ability. Bases are available for remote alarm LED indicator connections and auxiliary relay outputs. * LIFEalarm smoke detector operation is protected by one or more of the following U.S. Patents: 5,155,468; 5,173,683; 5,400,014; 5,543,777; 5,710,541; D383,407; D388,352; D392,573.

Operating Temp. Range 15° to 122 °F (–9° to + 50 °C) Humidity Range

10% to 95% RH from 32° to 122° F (0° to 50 °C) non-condensing

Color

Frost White

Dimensions

4 7/8 in. Dia. x 1 7/8 in. H, mounted in base (124 mm x 48 mm)

3-61

Smoke Detector Features

Application Reference

Intelligent Data Evaluation. Conventional smoke detectors will typically drift toward being too sensitive due to the accumulation of dust and dirt. With analog detection, data from the photoelectric chamber is monitored and analyzed at the detector to provide a continuously shifting reference point.

Detector Locations. Locations should be determined only after careful consideration of the physical layout and contents of the area to be protected.

Drift Compensation. The data evaluation and its shifting reference point provide a software filtering process that compensates for environmental factors (dust, dirt, etc.) and component aging, establishing an accurate reference for evaluating new activity. With this filtering, the resulting drift compensation provides a significant reduction in the probability of false or nuisance alarms caused by shifts in sensitivity – either up or down.

For further detailed installation information, refer to Detectors, Sensors, and Bases Application Manual (Part No. 431424). Sensitivity Selection. The standard sensitivity detector (Part No. 430559) is recommended for most applications. When a special application for a reduced sensitivity detector is required (Part No. 430562) should be considered.

Magnetic Test Information. Status information is available by performing the magnetic test and observing the detector LED pulses. The LED will normally go directly into alarm with the magnetic test. If there is an off-normal condition, the LED pulses first to indicate the condition and then goes into alarm. Product Selection Smoke Detectors Part No. 430559

Description

Nominal Sensitivity

Compatibility

LIFEalarm Photoelectric Detector

2.8%/ft (standard)

Compatible with detector bases: Part Nos. 430567 and 430569

430562

3.5%/ft

Compatible Bases Part No.

Description

Details

430567

2-Wire Base with connections for Remote Alarm LED Indicator

• IDC and LED connections are screw terminals for in/out wiring, 18 to 14 AWG

430569

2-Wire Base with Auxiliary Alarm Relay & connections for Remote LED Indicator Note: Must be connected as the only device on the IDC to ensure relay operation.

Relay Ratings, Dual Form "C", For Suppressed Loads: • Power limited, 1 A @ 28 VDC • Non-power limited, 1/2 A @ 120 VAC

430570

2-Wire Base with Remote LED Indicator

Wiring Connections (In/Out where required): • Relay s and IDC (–), color coded 18 AWG leads • IDC (+) and LED wiring, screw terminals for 18 to 14 AWG

Detector Accessories Part No.

Description

Details

430572

Remote LED Indicator

• Mounted on single gang stainless steel plate

Detector Status LED Indications LED Indication

Status

Pulses approximately every 4 seconds

Normal

Steady On

Alarm

LED Response to Magnetic Test * LED Indication

Followed By

Status

Action

LED turns ON

Alarm is initiated

Normal, sensitivity is within compensation range

None

LED pulses quickly, 6 times in 3 seconds, then turns ON

Alarm is initiated

More sensitive, out of normal compensation range

Cleaning or other service is required

Alarm is initiated

Less sensitive, out of normal compensation range

Does not initiate Alarm

Detector is malfunctioning

LED pulses slowly, 4 times in 8 seconds, then turns ON

Service is required

* Testing requires placing a magnet at the designated location on the detector cover for 4 seconds.

Dimensions and Reference Information 4 7/8 IN. (124 mm)

1 7/8 IN. (48 mm)


006565

LED STATUS INDICATOR (WITH CLEAR LENS) PART NO. 430559 AND PART NO. 430562 DIMENSIONS MOUNTED ON BASE

ALARM

006567


Mounting Information ELECTRICAL BOX REQUIREMENTS: WITHOUT RELAY (BASE, PART NO. 430567): 4 IN. (102 mm) OCTAGONAL OR 4 IN. (102 mm) SQUARE, 1 1/2 IN. (38 mm) DEEP SINGLE GANG, 2 IN. (51 mm) DEEP WITH RELAY (BASE, PART NO. 430569): 4 IN. (102 mm) OCTAGONAL, 1 1/2 IN. (38 mm) DEEP, WITH 1 1/2 IN. (38 mm) EXTENSION RING 4 IN. (102 mm) SQUARE, 1 1/2 IN. (38 mm) DEEP, WITH 1 1/2 IN. (38 mm) EXTENSION RING SURFACE MOUNT REFERENCE

4 IN. (102 mm) SQUARE BOX

4 IN. (102 mm) OCTAGONAL BOX



PART NO. 430569 INCLUDES A RELAY MODULE THAT MOUNTS IN BASE ELECTRICAL BOX

SMOKE DETECTOR BASES (PART NOS. 430567 AND 430569)

006566

SMOKE DETECTOR (PART NOS. 430559 AND 430562)



Detection and Control Components Electronic Heat Detectors For Two-Wire Bases (Z-10) Features

Specifications

Accurate and reliable heat detection for protection of property

Voltage

15 to 32 VDC (filtered DC with 30% maximum ripple)

Available with rate-of-rise temperature detection:

Standby Current

80 μA typical, 100 μA maximum

• Dual thermistor rate-of-rise operation


Up to 100 μA maximum, exact current is determined by alarm current limiting of connected IDC

• For use where anticipated ambient temperature changes are less than 6 °F/minute (3.33 °C/minute) Epoxy encapsulated electronic design provides: • Easily tested, self-restoring operation with repeatable accuracy • Alarm indicating LED located on detector

Rate-of-Rise Operation Meets FM requirements for operation between 15° and 25 °F/min (8.33° and 13.88 °C/min) Humidity Range

10% to 95% RH from 32° to 122 °F (0° to 50 °C), not intended for outdoor applications

Color

Frost-White

Dimensions

Refer to diagram on page 3

• Current limited alarm that is compatible with two wire initiating device circuits (IDCs) Optional remote alarm indicating LED Available base options: • Bases for 2-wire operation • Auxiliary relay output (refer to selection chart on for relay ratings) • Remote alarm indicating LED output

Ambient Temperature Operating Range 135° F Models

32° to 100 °F (0° to 38 °C)

200° F Models

32° to 150 °F (0° to 66 °C)

Description Rate-of-rise detection is determined by comparing two thermistor responses. By combining accurate thermistors with proper physical placement, this patented rate-of-rise detection design achieves a high level of performance not normally available with mechanical detection. Listings and Approvals

! WARNING Hazardous levels of smoke and toxic gas can build up before the heat detection device initiates an alarm. To ensure the safety of personnel, the use of smoke detection is highly recommended.

• UL Listed: S6651 Applications Reference

• ULC Listed: S6651

Heat detectors are used where property protection is desired and where life safety protection is not required or is performed by other equipment.

• FM Approved: 3015976 • CSFM (Approved) • MEA (NYC) (Approved)

The rate-of-rise operation provides heat detection for use where temperature fluctuations are controlled and are less than 6 °F/min (3.33 °C/min). Where temperatures may fluctuate more quickly, use fixed temperature detection. Refer to NFPA 72, the National Fire Alarm Code, for additional guidance in applying and locating heat detectors. Alarm Indicating LED Operation The heat detector LED turns ON continuously when in alarm. During normal conditions the LED is OFF. 006570

Electronic heat detector design is protected by the following U.S. Patents: 5,450,066; DES.377,460.

Electronic Heat Detector Mounted in Base

3-62

Heat Detector Selection Chart Part No.

Fixed Temperature Operation at

430565

135 °F (57 °C)

430566

Rate-of-Rise Operation Between 15° and 25° F/min (8.33° and 13.88° C/min)

200 °F (93 °C)

Heat Detector Base Selection Chart Smoke Detectors Part No.

Description

Connection

Details

430567

2-Wire Base, with connections for remote LED alarm indicator

IDC connections

Screw terminals for in/out wiring, 18 to 14 AWG

430570

2-Wire Base with remote LED alarm indicator

IDC connections

Screw terminals for 18 to 14 AWG for in/out wiring of zone (+), color coded 18 AWG leads for in/out wiring of zone (–)

LED connections

Color coded 18 AWG leads

430569

2-Wire Base with auxiliary alarm relay output

Relay Operation Type Relay Ratings Power-limited

1 A @ 28 VDC

Note: Must be connected as the only device on the IDC to ensure relay operation.

Nonpower-limited

3 A @ 120 AC

Output Type

Wiring Connections

IDC connections

Screw terminals for 18 to 14 AWG for in/out wiring of zone (+), color coded 18 AWG leads for in/out wiring of zone (–)

Relay connections

Color coded 18 AWG leads

Dual Form "C" s, for suppressed loads

Heat Detector Accessories Part No.

Description

Details

Base Compatibility

430572

Remote Red LED Alarm Indicator

Mounted on single gang stainless steel plate, wiring connections are 18 AWG color coded leads

Part No. 430570 only

430573

End-of-Line Relay

Epoxy encapsulated design, 24 VDC operation, wiring connections are 18 AWG color coded leads

—

Metric wire equivalents: 18 AWG = 0.82 mm2; 14 AWG = 2.08 mm2

Dimensions and Reference Information 4 7/8 IN. (124 mm)

2 3/8 IN. (60 mm)


006571

LED STATUS INDICATOR

ALARM

006567


Mounting Information Base

Electrical Box Requirements

430567

4 in. (102 mm) octagonal or 4 in. (102 mm) square box, 1-1/2 in. (38 mm) deep Single gang box, 2 in. (51 mm) deep

430569 430570

4 in. (102 mm) octagonal or 4 in. (102 mm) square box, 1-1/2 in. (38 mm) deep with 1-1/2 in. (38 mm) deep extension ring (see diagram below)

4 IN. (102 mm) OCTAGONAL OR SQUARE BOX


SURFACE MOUNT REFERENCE


BASE (PART NO. 430569) INCLUDES A RELAY THAT MOUNTS IN BASE ELECTRIC BOX BASE (PART NO. 430570) INCLUDES A REMOTE LED INTERFACE MODULE THAT MOUNTS IN BASE ELECTRICAL BOX

HEAT DETECTOR BASES (PART NOS. 430569 AND 430570)

006572

HEAT DETECTOR



Detection and Control Components Abort Switches and Releasing Appliance Circuit (RAC) Maintenance Switches (Z-10)

Features • Abort switches provide a manual Fire Suppression System release abort request: – Pushbutton momentary switch is mounted on a stainless steel single-gang plate – A protruding collar protects the switch from accidental (collar is removable if required) – Available flush or surface mount – Flush mounting requires standard single-gang box – Surface mounting includes a red mounting box 006549

– Models are available with internal 1.2kΩ resistor for current limited operation • Maintenance switches provide a secure and visible disconnect means for servicing Fire Suppression System Releasing Appliance Circuits (RACs):

Maintenance Switch with Disconnect Indicator Lamp Specifications Electrical Ratings

– Maintained position keyswitch is mounted on a stainless steel double-gang plate

Abort Switch; One block

Silver s; 1 NO & 1 NC; rated 2 A resistive @ 30 VDC

– Key is removable in either normal or disabled position

Maintenance Switch with Lamp; Two blocks

Circuit control: Silver s; 1 NO & 1 NC; rated 2A resistive @ 30 VDC

– Disabled position opens connection to output circuit to initiate a supervisory condition at the host

Lamp control: Silver s; 1 Form C; rated 2 A resistive @ 30 VDC

– Disconnect indicator lamp is a bright incandescent bulb with red lens, powered from separate 24 VDC – Available for flush or surface mount – Flush mounting requires a standard double-gang box

Maintenance Switch Indicator Light

– Surface mount models include a red mounting box • UL listed to Standard 864, 9th Edition

Replaceable 2 W incandescent bulb; 24 to 30 VDC typical; 83 mA @ 35 VDC; requires -separate 24 VDC

Wiring Connections Description Releasing systems typically require maintenance disconnect switches and often require abort switches. These abort and maintenance switches are clearly labeled and combine easy operation with rugged construction for high integrity operation.

Abort Switch

Terminal blocks for in/out wiring; 18 to 14 AWG wire (0.82 mm2 to 2.08 mm2)

Abort Switch with Current Limited Resistor

Terminal blocks for first wire connection; 18 to 14 AWG wire (0.82 mm2 to 2.08 mm2); 18 AWG wire lead for second wire connection

Maintenance Switch

18 AWG (0.82 mm2) color coded wire leads for suppression circuit; terminal blocks for lamp wiring; 18 to 14 AWG wire (0.82 mm2 to 2.08 mm2)

Environmental Ratings Temperature Range

32 °F to 120 °F (0 °C to 49 °C)

Humidity Range

Up to 93% at 90 °F (32 °C)

006550

Abort Switch

3-63

Abort Switch Installation Reference BOX WIDTH, 3 IN. (76 mm)

RED BOX IS SUPPLIED WITH SURFACE MOUNT ABORT SWITCH 2080-9057 OR 2080-9068

2 1/4 IN. (56 mm) INTO BOX

1/2 IN. (13 mm) ABORT SWITCH HEIGHT, 4 1/2 IN. (114 mm)

BOX HEIGHT, 4 13/16 IN. (122 mm)

SWITCH RECESS DEPTH 5/32 IN. (4 mm) REMOVABLE COLLAR

007712

ABORT SWITCH WIDTH, 2 3/4 IN. (70 mm)

SUPPLIED GASKET ATTACHES TO BOX; FIELD INSTALLED FOR FLUSH MOUNT; PRE-ATTACHED FOR SURFACE MOUNT

2 3/4 IN. (70 mm) NOTE: FOR FLUSH MOUNTING, USE A 2 3/4 IN. DEEP (70 mm) SINGLE-GANG BOX

Maintenance Switch Installation Reference BOX DIMENSIONS, 4 13/16 IN. (122 mm) SQUARE

2 1/4 IN. (56 mm) INTO BOX

RED BOX IS SUPPLIED WITH SURFACE MOUNT MAINTENANCE SWITCH

4 1/2 IN. (114 mm)

007713

MAINTENANCE SWITCH WIDTH, 4 9/16 IN. (116 mm) SUPPLIED GASKET ATTACHES TO BOX; FIELD INSTALLED FOR FLUSH MOUNT; PRE-ATTACHED FOR SURFACE MOUNT

Listings and Approvals

2 3/4 IN. (70 mm) NOTE: FOR FLUSH MOUNTING, USE A 2 3/4 IN. DEEP (70 mm) SINGLE-GANG BOX


ULC Listed . . . . . . . . . . . . . . . . . . . S8332

Part No. Description


CSFM . . . . . . . . . . . . . . . . . . . . Approved

433936 433937 433940

2 2 1

UL Listed . . . . . . . . . . . . . . . . . . . . S8332

MEA (NYC) . . . . . . . . . . . . . . . . . Approved


Flush Mount Maintenance Switch Surface Mount Maintenance Switch Flush Mount Abort Switch

(0.9) (0.9) (0.5)


Detection and Control Components Isolated Loop Circuit Protector, Part No. 430685 (Z-10) Features • Isolated Loop Circuit Protector (IL) for up to 5 A of DC or audio current: – Low impedance design minimizes voltage drop – For internal or external applications (refer to page 2 for external wiring requirements) – Refer to specific field wiring diagrams for additional application information

L I N E

• Operation is compatible with**:

E Q U I P

– DC notification appliance circuits (NACs) – Speaker circuit NACs (25 VRMS) • Multiple stages of protection for DC and audio circuits: – Line-to-Line Protection – Line-to-Earth Protection • Rugged epoxy encapsulated package Description Electrical transients caused by lightning or by disturbances on high voltage power lines are conditions that require low voltage wiring circuits to be adequately protected. This protection is most effective when placed at the location where such circuits leave or enter the building. The Isolated Loop Circuit Protector (IL) (Part No. 430685) is designed to protect Fire Alarm circuits from those electrical transients induced on wire runs that are routed external to the building. Because of its small package size, it can be easily mounted at the location that achieves maximum protection. ** Performance of this device has been quantified for use with other circuit types for specific applications where its low resistance is desired.

Listings and Approvals UL Listed . . . . . . . . . . . . . . . . . . . . . E197916

006581

Isolated Loop Circuit Protector (Part No. 430685)

Operating Specifications Line-to-Line Rating Line-to-Ground Rating

38 VDC, 28 VAC RMS

Shield-to-Ground Rating

48 VDC, 33 VAC RMS

Continuous Current Rating

5A

Series Resistance

0.1 Ω/line

Series Inductance

68 μH/line

Shunt Capacitance

0.017 μF

Response Time

<1 Nanosecond (10-9) line-to-line and line-to-earth

Maximum Current Line-to-Line and Line-to-Earth Maximum Current Shield-to-Earth

2000 A (8 x 20 μsec pulse) 5000 A (10 x 50 μsec)

Mechanical Specifications Dimensions

3 3/8 in. W x 2 in. D x 1 in. H (86 mm x 50 mm x 25 mm)

Package

Epoxy encapsulated, beige

Electrical box requirement

4 in. (102 mm) square box, 2 1/8 in. (54 mm) minimum depth

Wire Leads

Color coded, #18 AWG, 8 in. long (203 mm)

3-64

External Wiring Requirements

Overhead Wiring

Fire alarm system wiring that is run external to the building and is protected by the use of ILs shall be installed in accordance with the individual system component’s installation instructions including properly grounded, twisted and shielded pairs, and observance of the following precautions.

1. Wiring must be run on poles separate from those ing any commercial power distribution wiring.

Location. To ensure optimized protection, the ILs shall be located as close as possible to the point at which the circuits leave or enter the buildings and installed in dedicated metallic electrical boxes. Wiring Distance. Wiring is limited to one contiguous property. The total maximum wire length is determined by the individual application’s allowable limit as specified with ILs, but must not exceed 3270 ft (996.7 m).

2. Wiring shall be run in parallel with the commercial power distribution wiring and be separated by a minimum distance of either 100 ft (30 m) or the maximum span between any two adjacent poles of either the system’s circuit or the commercial power distribution circuit. The grounding conductor shall be #12 AWG with a maximum length of 28 ft (8.5 m), run in as straight a line as possible and connected to the building grounding electrode system (unified earth ground) per Article 800-40 of NFPA 70, the National Electrical Code.

Underground Wiring. Wiring must be in a wiring trough that is separate from commercial power distribution wiring.

Typical Connections INDOORS

OUTDOORS

INDOORS

PROTECTED EQUIPMENT

IL (PART NO. 430685) LINE A

TO THE NEXT CONNECTED

LINE B

PROTECTOR

INTERNAL CIRCUIT

LINE A

LINE B

CABLE SHIELD (IF USED)

006584

CABLE SHIELD (IF USED)

GROUND SCREW

GROUND SCREW

# 12 AWG (MIN.)

# 12 AWG (MIN.) 28 FT (8.5 m) MAX.


4 IN. (102 mm) SQUARE BOX, 2 1/8 IN. (54 mm) DEEP OR EQUIVALENT (BY OTHERS)



ANSUL AUTOMAN II-C Releasing Device Applications The ANSUL AUTOMAN II-C is an automatic, electric pneumatic releasing device for actuating a fire suppression system upon receipt of an electrical input signal. It may be automatically actuated via a detection/control system and/or manually through use of an integral manual strike button; or through use of a remote electric or remote mechanical pull station. Description The device is made up of an enclosure, releasing device and auxiliary switch. The NEMA Type I all-steel enclosure has four holes for surface mounting and a hinged cover with key lock. The cover contains a window for visual verification that the releasing device is armed. A standard pattern of wiring knockouts is provided, and connections are made to heavy duty screw terminals – no soldering required. The releasing device has a stored pressure cartridge (order separately) and provides pneumatic actuation for the release mechanisms on agent container tanks. Pressure is released from the cartridge by piercing the cartridge seal with a mechanical puncture pin. The pin release can be accomplished manually through a STRIKE button on the front cover or automatically through the solenoid. Optional electric or mechanical manual pull stations provide additional actuation capability, if desired. An auxiliary switch may be used to provide shutdown of equipment or provide of actuation to the detection/control system. Technical Information Temperature Range:. . . +32 °F to +120 °F (0 °C to +49 °C) Solenoid Voltage:. . . . . . . . . . . . . . 24 VDC Nominal Solenoid Operating Current: . . . . . . . 750 mA @ 24 VDC Solenoid on Time: . . . . . . . . . . . . . . . . . . . 50 mS Coil Resistance: . . . . . . . . . . . . . . . . . . . . . 26Ω

004653

The release contains a second integral switch which shuts off the solenoid after operation, approximately 50 mS. Supervision can be accomplished by ing a limited current of 50 mA or less through the solenoid circuit. The number of devices that can be operated from the pneumatic output of one ANSUL AUTOMAN II-C is determined by the minimum anticipated temperature, the amount of piping required, and the nature of the devices being actuated. If additional actuation capability should ever be required as an option, remote pressure booster type actuators can readily fill the need. MOUNTING DIMENSIONS

5/16 IN. DIAMETER HOLES 4 1/4 IN. (108 mm)

1 1/8 IN. (29 mm)

9 7/8 IN. (251 mm)

Auxiliary Switch Ratings: . . . . . 20A, 125/250VAC 2 HP, 250VAC 1 HP, 125VAC

1 IN. (25 mm)

22 1/8 IN. (562 mm)

Weight: . . . . . . . . . . . . . . . . . . . . 26 lb (11.8 kg) Overall Dimensions: Height. . . . . . . . . . . . . . . . . . 24.5 in. (662 mm) 000466

Width . . . . . . . . . . . . . . . . . . 12.5 in. (311 mm) Depth . . . . . . . . . . . . . . . . . . 4.25 in. (108 mm)

000465

KNOCKOUTS ON 4 SIDES OF BOX

3-65

Approvals The ANSUL AUTOMAN II-C releasing device is Underwriters Laboratories listed for use with piped, fixed nozzle fire suppression systems (R5998). It complies with the requirements of all current applicable NFPA standards covering fire extinguishing agent systems. Ordering Information Part No. Description


17728

ANSUL AUTOMAN II-C Assembly

26

(11.8)

35619

Weatherproof ANSUL AUTOMAN II-C Assembly

28

(12.7)

17966

Lock with 2 Keys

0.25

(0.1)

70480

Key

0.1

(0.05)




ANSUL AUTOMAN II-C Explosion-Proof Releasing Device Applications The explosion-proof ANSUL AUTOMAN II-C is an automatic, electric pneumatic releasing device which, upon receipt of an electrical input signal, actuates the fire suppression system which is installed in a hazardous location. It may be automatically actuated via a detection/control system and/or manually through use of an integral manual strike button; or through use of a remote electric or, mechanical remote pull station. Description The device is made up of an enclosure, and releasing device. The NEMA Type I all steel enclosure has four holes for surface mounting and a hinged cover with key lock. The cover contains a window for visual verification that the releasing device is armed. Wiring knockouts are provided, and connections are made to the solenoid through two 18 AWG leads exiting the conduit fitting on the explosion-proof solenoid. The releasing device uses a stored pressure nitrogen cartridge and provides pneumatic actuation for the agent container tank valve. Pressure is released by piercing the cartridge seal with a mechanical puncture pin. The pin release can be accomplished manually through a STRIKE button on the front cover or automatically through the solenoid. Optional electric or mechanical manual pull stations provide additional actuation capability, if desired. To provide shutdown of equipment or provide of actuation to the detection/control equipment, an explosionproof pressure switch (not provided) can be added to the system. The explosion-proof releasing device is suitable for use in the following areas: Class I, Groups C and D Hazardous Locations. Technical Information Temperature Range: . . . . . 32 °F to 130 °F (0 °C to 54 °C) Part Number: 31492 32525 32526 _____ _____ _____ Operating Voltage:. . . . 24 VDC 120 VAC 240 VAC Operating Current:. . . . 500 mA 100 mA 50 mA Coil Resistance: . . . . . 52 ohms 100 ohms 200 ohms Solenoid Rating: . . . . . Explosion-proof, Continuous Duty Weight:. . . . . . . . . . . . . . . . . . . . . 26 lb (11.8 kg) Overall Dimensions: Height . . . . . . . . . . . . . . . . . . 24.5 in. (662 mm) Width . . . . . . . . . . . . . . . . . . 12.5 in. (311 mm) Depth . . . . . . . . . . . . . . . . . . 4.25 in. (108 mm)

004653

CAUTION The explosion-proof ANSUL AUTOMAN II-C CANNOT be used with a CO2 Cartridge. Although other cartridges will fit, they MUST NEVER be used in this unit. Use only the LT-30-R Nitrogen cartridge (Part No. 5373). The solenoid employed is rated for continuous duty. Should it be desirable to interrupt power to the solenoid after system actuation, an explosion-proof pressure switch can be utilized. The number of devices that can be operated from the pneumatic output of one ANSUL AUTOMAN II-C is determined by the minimum anticipated temperature, the amount of piping required, and the required pressure to operate the devices being actuated. If additional actuation capability should ever be required, as an option, remote pressure booster type actuators can readily fill the need. MOUNTING DIMENSIONS

5/16 IN. DIAMETER HOLES 4 1/4 IN. (108 mm)

1 1/8 IN. (29 mm)

9 7/8 IN. (251 mm)

1 IN. (25 mm)

22 1/8 IN. (562 mm)

000466 000465

KNOCKOUTS ON 4 SIDES OF BOX

3-66

Listings and Approvals The ANSUL AUTOMAN II-C explosion-proof releasing device is Underwriters Laboratories listed (E62842) for use in Class 1, Groups C and D Hazardous Locations with piped, fixed nozzle fire suppression systems. It complies with the requirements of all current applicable NFPA Standards covering fire extinguishing agent systems. Ordering Information Part No. _________ Description _______ 31492 ANSUL AUTOMAN II-C Explosion-Proof Releasing Device, 24 VDC 32525 ANSUL AUTOMAN II-C Explosion-Proof Releasing Device, 120 VAC 32526 ANSUL AUTOMAN II-C Explosion-Proof Releasing Device, 240 VAC


Shipping Weight lb (kg) ___________ 26 (11.8)

26

(11.8)

26

(11.8)


T-2007097 59xx

Overview 6h3y3j

More details h6z72

More Documents from "Ravi" 32y3e

Communication Theories In Action Pdf 3i5f36

Online Motor Vehicle Registration Process In E Pragathi 3b3s56

Satellite And Radar Communication 5j5f3c

Sparc M7 Processor Architecture 3j212d

T-2007097 59xx

Powerful Mantra For Job 284u4z