Span - Septic Tank Volume Calculation.pdf 616a16

Section 1 Introduction

Introduction

1.1

Purpose of This Volume



This volume sets out the requirements of the National Water Services Commission (SPAN), referred to as the Commission in this document for the design and construction of individual septic tanks within developments.



This volume applies to multi-unit housing; mixed and individual residential or commercial developments with a population equivalent (PE) size up to 150, where the use of individual septic tank is being considered.



Developments of more than 150 PE shall not employ the use of septic tanks.



An individual septic tank can only serve one premise. The largest capacity of individual septic tank shall not be more than 30 PE. Where the design PE is more than 30 for a single unit of building or sub-divided lots, other system of treatment shall be provided. Furthermore, the use of multiple individual septic tanks within a single sub-divided lot is not allowed.



Sewage Treatment Plant shall be used for treatment more than 30 PE developments in single unit type as given in MSIG Volume 4.



The developer shall consult the following MSIG for developments that falls outside the scope of this volume, namely:



◆ ◆ ◆ ◆



Volume 1

Sewerage Policy for New Developments

Volume 2

Sewerage Works Procedures

Volume 3

Sewer Networks and Pump Stations

Volume 4

Sewage Treatment Plants



The of this volume of the MSIG shall also refer to Volume 3 of the above guidelines on the provision of oil and grease interceptors to protect sewerage treatment systems from the discharge of these matters from hotels, restaurants, canteens, garage workshops or any premises that collects such matters.



This volume does not cover the installation of internal plumbing systems to buildings. The requirements for internal plumbing systems are managed by the relevant Local Authorities.

Septic Tanks

Volume 5

3

Introduction

1.2

Effluent Discharge Standards and Requirements



The Environment Quality Act (EQA) 1974 specifies two standards for effluent discharge. These are namely Standard A for effluent discharge located upstream of raw water intake points and Standard B for effluent discharge located downstream of the raw water intake points. The current Third Schedule of the Environmental Quality Act 1974, under the Environmental Quality (Sewage and Industrial Efluents) Regulations 1979, regulations 8 (1), 8 (2) and 8 (3) has been revisited and the Department of Environment (DOE) has proposed 8th Schedule for the Act which stipulate effluent discharge limits for parameters specific to domestic wastewater. The effluent discharge limits in 8th Schedule are summarised in Appendix B.



Due to the limitations in a septic tank in providing primary wastewater treatment only, its treatment performance may not be on a consistent basis to meet the strict DOE absolute standards. Further, its performance is also subjected to quantity of settled solids which has accumulated over time. The settled solids reduce the volume available for sewage treatment and compromises its efficiency of treatment. For these reasons, the design of septic tanks for effluent discharge downstream of water intake points shall be based on an average effluent quality of



BOD5 Suspended Solids

: 50 mg/l : 100 mg/l



To achieve a higher quality of treated effluent discharge within catchment located upstream of water intake points, the design of the septic tank must be coupled with further forms of treatment as recommended in Section 4.0 of this Volume.



It is of paramount importance to meet the above treated effluent quality and achieve the overall environmental objectives. hence, the design of septic tanks must allow for regular desludging at a frequency of NOT less than once every two (2) years.

1.3

Who Should Use This Volume



This volume is primarily intended for owners, architects, town planners, suppliers, developers and their consulting engineers, public authorities and others whose developments intended to use septic tanks.

4

Volume 5

Malaysian Sewerage Industry Guidelines

Introduction

1.4

Related Reference Material



This volume does not cover all aspects of design and construction of septic tanks. Where information is not covered in this volume, the designer shall follow the requirements given in MS 1228: 1991 Code of Practice for Design and Installation of Sewerage Systems.

However, the information in this volume shall take precedence over MS 1228, where similar aspects are covered in both these documents or where there is conflicting information between the two documents.

The procedures for certification of sewerage services are given in the MISG Volume 2 Sewerage Works Procedures.



The following documents are also referred to in this volume.



Malaysian Standards



◆



Other Documents





◆ ◆



Other Guidelines in This Set



The Malaysian Sewerage Industry Guidelines is also comprised of other 4 volumes:



◆ Volume ◆ Volume ◆ Volume ◆ Volume



Septic Tanks

MS 1228:1991 Code of Practice for Design and Installation of Sewerage Systems or its latest version.

Environmental Quality Act, 1974

Water Services Industry Act, 2006

1

Sewerage Policy for New Developments

2

Sewerage Works Procedures

3

Sewer Networks and Pump Stations

4

Sewage Treatment Plants

Volume 5

5

Section 2 General Guidelines

General Guidelines

2.1

Initial Consultation



Before submitting Application for Sewerage Works Planning Approval, the owner shall consult the Commission to determine one of the following forms of sewage treatment appropriate for the proposed development:



◆ ◆ ◆



Connect to existing public sewer. Individual septic tanks. Comply with effluent Standard A or B while meeting with local environmental standards.



It is advised that the matters listed in section 2.2 and 2.3, and 2.4 for homestead developments, are discussed and clarified before making a formal application to the Commission.

2.2

Where a Public Sewer is Available



The development must be connected to a public sewer if it is located within 30 metres of the proposed site. Volumes 2 and 3 of the MSIG provide procedural and design information on sewer connection.

2.3

Where No Public Sewer is Available



Where a public sewer is not available, the developer shall consider the following before proceeding:



a)



b)



c)



Note: This Guidelines should only be used for developments served by individual septic tank.

Septic Tanks

Investigate if there are existing forms of sewage treatment available in the vicinity of the proposed development. Liaise with the Commission to determine if there are any immediate or future proposals for sewerage works in the vicinity of the proposed development for possible connection.

Current guidelines, standards or special requirements with respect to sewerage works and treated effluent standards.

Volume 5

9

General Guidelines

2.4

Homestead Developments

2.4.1

Single Development up to 30 Units or 150 PE in Total



Individual septic tanks may be allowed for single developments of up to 30 units or 150 PE in total.



Septic tanks will be regarded as temporary treatment systems.



The owner must provide all septic tanks as part of the owner’s infrastructure works. Septic tanks must be constructed to standard design.



The owner must provide a 150 mm by- pipe from the last manhole before the septic tank and extended to the outside drain line of the premises. The pipe end shall be capped for future connection. Please refer to Section 3.2.8 of this Volume for further details.

2.4.2

Single Development Over 30 Units in Total with Average Housing Density Greater Than Five Units per Hectare



For single development over 30 units in total with an average housing density greater than 25 persons per hectare, a sewer reticulation and a treatment plant must be provided.



Sewer reticulation must be appropriately designed to achieve acceptable hydraulic conditions within topographic and routing parameters.

2.4.3

Single Development Over 30 Units in Total with Average Housing Density Less Than Five Units per Hectare



For single development over 30 units in total and with an average housing density of less than 25 persons per hectare, a sewer reticulation and a treatment plant is preferred.



Where the terrain of the development is such that installation of an approved treatment system mandating the construction of excessive numbers of intermediate pump stations; individual treatment facilities may be considered, subject to the following conditions:



a)



b)

10

The individual system must be a system approved by the Commission.

Where the ground conditions permit, soakaway trenches must be used for disposal of the final effluent from the treatment systems.

Volume 5

Malaysian Sewerage Industry Guidelines

General Guidelines



c)



d)



e)



All septic tanks shall be designed in accordance with the requirement of this Guidelines.

2.4.4

Individual Development outside Local Authority Areas



Owners in rural catchments must be encouraged to use the types of Individual Septic Tanks (IST) approved by the Commission instead of ‘Others’ type of sanitary system



Local Authorities must liaise with the Commission before approving sewerage plans for developments or individual owners. Local Authorities shall advise the owners on the following:



a)



b)



d)



f)





c)

e)

Septic Tanks

Developers shall ensure that home owners enter into an agreement with the supplier of the system or licensed contractor approved by the Commission, to carry out operation and maintenance of the system as per design requirements.

Tanks shall be desludged by the Services Licensee as per of the agreement signed between the Services Licensee and the Government.

The Commission and DOE may impose stringent conditions, if they believe that such measures are required to ensure that the sewage from the development will not result in an adverse impact to the environment.

IST suppliers and the product must be approved by the Commission. Must comply with effluent quality standard

Where ground conditions permit soakaway, trenches must be provided for disposal of final effluent from their IST Where water table is high, raised soakaway shall be provided

Local Authorities must ensure that the ISTs in their jurisdiction must be desludged by desludging contractor ed with the Commission All soakaway must be located at least 5m downstream of wells for domestic consumption.

Volume 5

11

Section 3 Design Guide

Design Guide

3.1

General



The selection and design of septic tanks is governed to a large extend by the hydraulic aspects of the treated effluent discharge to a suitable watercourse. In situations where the topography is undulating or hilly, the treated effluent maybe discharged readily to a suitable receiving watercourse such as storm drains. However, in generally flat topography there may not be a conveniently located receiving water course or nearby drain for the treated effluent to be discharged to. In these cases, the design of the septic tank must incorporate a method for an on-site final disposal of treated effluent.



Where the discharge of septic tank effluent is located upstream of water catchment areas and/or in certain sensitive receiving water courses, the design standards shall be more stringent in order to achieve an effluent quality higher than standard B. The design of these septic tanks must include additional elements or features of design to ensure that the performances of such septic tanks are able to comply with the relevant Environmental Quality Act requirements consistently. The discussions on these methods are prompted in Section 4.0 of this volume.



Organic loading from the incoming raw sewage shall be based on 250 mg/ℓ of BOD5 (5 days at 20oC) per population equivalent per day, and 300 mg/ℓ of suspended solids per population equivalent per day.



In Malaysia, there exist two (2) forms of septic tank which have found wide usage. The first type is a cast in-situ septic tank previously promoted by the Ministry of Health. The cast in-situ septic tank consists of a septic tank with a minimum of 24 hours hydraulic retention time followed by a dual size aggregate down flow filter media. The second type is the prefabricated septic tank manufactured locally using polyethylene, glass fiber reinforced plastic or reinforced precast concrete materials. The filter chamber for prefabricated septic tanks is incorporated inside of the septic tank on the outlet section (as opposed to the filter chamber located externally in the cast in-situ septic tanks) to enhance its performance.



One fundamental difference between the cast in-situ and the prefabricated septic tanks is the size of the filter employed. The cast in-situ employs the use of stone filter several orders of magnitude larger than the typical proprietary filter media used in the prefabricated septic tanks. The other distinction is the direction of flow employed. The stone filters employ the use of a down-flow scheme while the proprietary filters use an upflow scheme. Both of the fundamental differences have some bearing on the treatment performance and the site (topography); where each type of the septic tank may have special niche in its applications.

Septic Tanks

Volume 5

15

Design Guide



Prior to the selection of septic tank for adoption in any development, the designer shall pay particular attention to the following:



a)



Volume of septic tank required to result in the sedimentation and subsequent biological breakdown of organic solids of the wastewater. b) Quality of constructed septic tank to prevent leakage of septic tank contents and the ingress of surrounding groundwater. c) Adequacy of the ventilation aspects to allow for safe operation and maintenance. d) Siting aspects with respect to public health concerns and the provision of adequate access for desludging works. e) Compliance of the treated effluent quality as prescribed in Section 1.2. f) The uplifting effects due to buoyancy during installation and during desludging activities. g) High water table and poor soil conditions to be considered.



The designer shall also refer to MS 1228.

3.2

Planning



Careful planning prior to the implementation of septic tanks is crucial to achieve the overall environmental objectives; protection of public health; safety and health of workers and ease of maintenance. As such, the designer must satisfy the following considerations before proceeding with the design, selection and construction of septic tanks.



i) ii) iii) iv) v) vi) vii)

3.2.1

Site Selection



The siting of the septic tank shall meet the following:



a)



b)



16

Site Selection Maintenance Vehicle Access Safety Requirements Desludging Works Location of Septic Tank within Premise of Property Inspection Chamber Septic Tank Drawings

Located within 30 m of desludging vehicle access which has a minimum width of 4.5 m.

At a suitable land and location to allow desludging works to be carried out without posing hazard to building occupants, maintenance and desludging operators. Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide



c)



d) e)



f)



g)



h)



i)

Effluent discharge point away from building structures to preserve the structural integrity. Minimum distance of 0.5 m away from plot boundary. Minimum distance of 15 m away from underground water storage tank. Minimum distance of 6 m upslope or 3 m downslope from swimming or wading pools. Minimum distance of 30 m away from any water body currently being used or has future potential usage for drinking and/or cleaning purposes. Located in an area not subjected to heavy vehicle, foundation or other imposed loadings. Away from areas subjected to flooding.

The designer is expected to fulfill the above requirements at all times. In conjunction with the above, the designer shall also refer to Section 3.2.5 on the location of septic tanks within premise.

3.2.2

Maintenance Vehicle Access



The Water Services Industry Act 2006 has the following clauses relating to vehicle access for desludging and other maintenance works:



Section 64 Clause (2): If the Commission is satisfied that, due to any obstruction, any premises on which a septic tank is situated does not have adequate access for the purpose of desludging the septic tank, the Commission may issue a direction to the owner, management corporation or occupier of such premises to remove such obstruction within the period specified in the direction.



Section 65 Clause 1.a and 1.d: The owner, management corporation or occupier of any premises having a private sewerage system or septic tank shall



a)



b)



Sufficient access must be provided to allow desludging and maintenance works to be carried out without undue difficulty to the maintenance workers or compromise the public health and aesthetic impacts. As such, the following should be provided:

Septic Tanks

grant the service licensee or permit holder adequate access to the septic tank for the purpose of enabling the septic tank to be serviced and desludged;

grant the service licensee or permit holder adequate access to the private sewerage system for the purposes of enabling the private sewerage system to be inspected, serviced or maintained.

Volume 5

17

Design Guide



a) b)



c)



d)

3.2.3

Safety Requirements



a)

The septic tanks are not to be located in areas where it is likely to encounter naked flames to reduce the likelihood of explosions.



b)

Care must be taken when entering septic tanks. Ensure that the gases in the septic tanks are thoroughly ventilated before entry.



c)

Any naked flames must be extinguished, and regulations regarding entry into confined spaces must be observed at all times.

3.2.4

Desludging Works



Considering that prolonged settlement of solids in the septic tank would eventually result in the level of solids to build up and subsequently reduce the treatment capacity of the septic tank; desludging is required at the frequency of not less than once every two years to restore the designed treatment capacity.



A minimum opening of 250 mm diameter with clear access age of 150 mm diameter shall be provided for desludging purposes at the sedimentation zone.

3.2.5

Location of Septic Tank within Premise of Property



The following considerations shall be observed in determining the final location of septic tanks within the premise of property:



a)









18

b)

Minimum width of access road shall be 4.5 m. No undue obstructions in the access road to prevent vehicle movement to reach the intended site. Adequate access to allow desludging vehicle to operate within the range of the suction-lift of the pump and length of hose. Septic tank covers as outlined in Section 3.3.6

Within the boundary of property served.

Externally located of building(s) served.

c)

Open space.

e)

Close proximity to receiving water course for treated effluent discharge.

d)

Fully accessible.

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide



Septic tanks shall be situated at the rear end of properties to allow for maintenance vehicle movements and to minimise visual impact. However, if this is not possible due to inavailability of backlane access, it shall be located at the front end.



Typical layouts for the various types of development are depicted in Appendices C, D, and E respectively for rear and front vehicle accesses.

3.2.6

Inspection Chamber



Inspection chambers are required where septic tanks are installed for maintenance purposes. It is required at the following locations:



a)

Maximum of 1 m and upstream of inlet to septic tank.



b)

At each bend.



c)

At every 20 m interval of sewer length outside the building.



d)

Inspection chambers shall be located at least 1 meter away from the building line.



Detail locations of inspection chamber shall be referred to Section

3.2.7

Septic Tank Drawings



Detailed plans of the proposed septic tank shall provide:



a)



The location of the septic tank in relation to: -

the building and adjacent buildings



-

point of discharge for treated effluent such as drains and soakaways



-

the plot boundary



-

the house drainage system



-

adjacent water supplies



-

the nearest access point for desludging



A longitudinal section to a scale of not greater than 1:50 showing the method of construction, materials, access covers, arrangement of compartments, pipework, baffles, media and critical dimensions.

Septic Tanks

b)

Volume 5

19

Design Guide



c)



d)



e)



f)

3.2.8

Future Connection to Public Sewers from Proposed/Existing Septic Tank



Septic tanks are considered as temporary treatment systems due to its primary treatment capability. Allowance for future connections to a sewer is therefore mandatory. As such, the following conditions must be observed:



a)

A 150 mm diameter by pipe from the last inspection chamber upstream of the septic tank to the outside drain line of the premises and end capped, or plugged, for future connection must be provided. The 150 mm diameter by pipe and accessories shall comply with the list for sewer pipes as given in MSIG Volume 3. Rubber cap or plug must be easily dismantled without resulting damages to the piping system, floor, building structures, exterior drain and backlane.



b)

Allowance of sufficient area at the rear section of buildings, preferably an access road, to lay connecting sewer lines from each house to the main sewer line.



c)

Provision for an easy change-over from septic tank treatment to connected system including, simple removal of cap/plug; sealing up of openings and back-filling the emptied septic tank with sand.



20

A plan of the septic tank and filter to a scale of not greater than 1:50 showing the general arrangement of pipeworks, compartments, baffles and channels and critical dimensions. Point of discharge of final treated effluent to the drain, water course or soakaway system.

Details of the proposed subsequent treatment methods such as soil absorption, etc.

Where no special conditions are imposed by the Commision, approvals will be facilitated by the use of standard drawings pre approved by the Commision.

See Appendix F and G for the location and typical details of the by line.

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide

3.3

Design

3.3.1

Volumetric Capacity



The volumetric sizing of septic tanks shall be based on per capita wastewater generation rate of 225 litres/day and for a hydraulic retention time of 24 hours. This is the effective working volume which is required for the biological degradation of the wastewater and excludes the volume of “head room” of air above the water level, accumulated sludge volume for 2 years and filter media if placed within the septic tank. This minimum volumetric capacity of septic tanks shall not be less than 2000 litres or 2 cubic meters.



The minimum effective working volume shall be calculated excluding filter media volume and accumulated sludge volume over 2 years. This is to ensure the individual septic tank is able to meet the 24 hours hydraulic retention time after 2 years of installation.



Septic tank with capacity up to 6 PE, the minimum effective working volume required shall be 2000 litres including accumulated sludge volume over 2 years period.



Example for Computing the Working Volume and Accumulated Sludge Volume for Septic Tank

Working Volume, C Where, C PE Desludging Period Hydraulic Retention Time

= 225 x PE



Sludge Accumulation Rate

= 0.04 m3/PE.year



Desludging Period (year) =



= Working volume in litres = Population Equivaleut (refer to Appendix A) = 2 years = 24 hours

(Accumulated sludge volume, m3)

(Sludge accumulation rate, m3/PE.year) x (PE)

Effective Working Volume = Working volume + Accumulated sludge volume

Septic Tanks

The effective volumes for the varies PE for septic tank are shown in Table 3.1

Volume 5

21

Design Guide

Table 3.1: Working Volume and Accumulated Sludge Volume Requirements for Different Size of Septic Tank Population Equivalent (PE) 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Minimum Working Volume L 1125 1350 1575 1800 2025 2250 2475 2700 2925 3150 3375 3600 3825 4050 4275 4500 4725 4950 5175 5400 5625 5850 6075 6300 6525 6750

m3 1.125 1.350 1.575 1.800 2.025 2.250 2.475 2.700 2.925 3.150 3.375 3.600 3.825 4.050 4.275 4.500 4.725 4.950 5.175 5.400 5.625 5.850 6.075 6.300 6.525 6.750

Accumulated Sludge Volume in 2 years L 400 480 560 640 720 800 880 960 1040 1120 1200 1280 1360 1440 1520 1600 1680 1760 1840 1920 2000 2080 2160 2240 2320 2400

m3 0.40 0.48 0.56 0.64 0.72 0.80 0.88 0.96 1.04 1.12 1.20 1.28 1.36 1.44 1.52 1.60 1.68 1.76 1.84 1.92 2.00 2.08 2.16 2.24 2.32 2.40

Required Effective Working Volume L m3 1525 1.525 1830 1.830 2135 2.135 2440 2.440 2745 2.745 3050 3.050 3355 3.355 3660 3.660 3965 3.965 4270 4.270 4575 4.575 4880 4.880 5185 5.185 5490 5.490 5795 5.795 6100 6.100 6405 6.405 6710 6.710 7015 7.015 7320 7.320 7625 7.625 7930 7.930 8235 8.235 8540 8.540 8845 8.845 9150 9.150

3.3.2

Compartmentalisation



Cast in-situ septic tanks shall be designed with two or more compartments. The capacity of the first compartment shall not be less than two thirds of the total volume. The division wall in two compartment tank shall have openings of at least 100 mm with a total area of at least 150 cm2. Openings shall be located at mid-liquid depth. The division wall shall have a ventilation air space at the underside of the roof to allow the free age of gases.

22

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide



The prefabricated septic tank could be provided with a baffle wall or scum box to isolate scum, oil and grease from entering the filter media. Prefabricated septic tanks with baffle walls, the filter chamber allows the flow from all direction. The scum, oil and grease will be captured at the inlet section of the baffle wall.



Where baffle wall is not provided in the design, an impermeable filter media chamber could be adopted as a baffle wall as it only allows an up-flow from the bottom end of the filter chamber. The impermeable chamber acts as a baffle or scum box which helps to prevent scum, oil and grease from entering the filter media. Under this arrangement, the impermeable baffle wall shall be extended to level with maximum 150 mm above the top level of accumulated sludge at the bottom of septic tank over period of 2 years.



For vertical flow septic tank, baffle wall or scum box shall be provided to prevent scum and Oil & Grease (O&G) from entering the filter chamber. Wall of filter chamber could be considered as baffle wall if up-flow filter chamber is adopted.

3.3.3

Inlet and Outlet



The inlet pipes to and outlet pipes from the septic tank shall be a minimum diameter of 100 mm and by means of dip pipes made of cast iron, or uPVC with sufficient stiffness and thickness located below the scum level. The inlet dip pipe shall utilise a T-shape pipe and the outlet dip pipe shall utilise a 90° elbow pipe.



The difference in level between the invert level of the inlet pipe and the invert level of the outlet pipe shall be a minimum of 75 mm. The minimum distance between the inlet pipe and the outlet pipe shall be 1300 mm.



The depth of the submerged end of the inlet dip pipe shall be extended to a minimum of 300 mm below the water level. In the outlet pipe section, the depth of the submerged end of the outlet dip pipe shall range from 375 mm to 610 mm below the water level. The non-submerged ends of both inlet and outlet dip pipes shall be projected of at least 150 mm above the water level.



See Appendix H, I and J for graphical presentation of the above description.



To minimise turbulence, provision shall be made to limit the velocity of the incoming wastewater. For steeply laid sewer or drains up to

Septic Tanks

Volume 5

23

Design Guide

150 mm in diameter, the velocity may be limited by laying the last 12 m of incoming pipe to a gradient of 1 in 50 or flatter. 3.3.4

Effluent Discharge



In situations where gravity discharge is not possible, the effluent shall be discharged through pumping. Pumped discharge can be accomplished through the use of submersible pumps located in a pump well. The following provides the requirements for the submersible pump and pump well, respectively:



Submersible Pump



a)



b)

Minimum motor rating of 0.3 kW to ensure trouble-free operation. Minimum design life of 10 years.



c)



Pump Well



a)



b)



c)

Selection to consider economic costs, reliability, pumping curve and compatibility with application.

Effective working volume to retain one (1) hour peak flow.

Emergency storage capacity of 200 litres in the event of power or pump failures. Minimum diameter of 600 mm.



d)



e)

3.3.5

Head Room



The space between the top water level and the underside of the tank shall be a minimum of 250 mm and must be adequately ventilated or provided with an adequate means of drawing off gases. A minimum of 50 mm diameter pipe or a minimum of 75 mm diameter ventilation duct provided in the septic tank to the exterior shall be proofed against the entry of mosquitoes by a fine mesh screen. The design of all septic tanks shall prevent mosquito breeding. All covers shall be air tight.

24

Incorporation of high level alarm light and/or on audible device within the building serve to detect pump failures.

Pump sets and control switches shall be installed in accordance with manufacturer’s specification and to Energy Commission requirements.

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide

3.3.6

Covers



The covers of the septic tank and inspection chamber shall be adequately reinforced to take superimposed loadings. These cover shall be airtight, and may be of light duty if not subjected to vehicular loading. If these cover are subjected to higher loading then suitable covers shall be used based on this higher loading the cover shall come with hinge and lock.



Where bigger cover is required due to deep sited tanks chequered plate of mild steel or ductile iron with protective coating may be used. The chequered plate shall be of reasonable size, having a maximum weight of 16kg/piece, to facilitate its removal and handling. Secondary air tight covers shall be provided at the septic tank opening when chequered plates are provided at ground level. The secondary covers shall be airtight and manufactured in accordance to the relevant standards.



Covers shall be located where it can be easily removed and accessable during desludging works.

3.3.7

Construction



Septic tanks may be constructed of brickwork or concrete while prefabricated septic tanks shall be prefabricated from polyethylene, glass fiber reinforced plastic or pre-cast concrete.



Brickworks shall be of engineering bricks in cement mortar and shall be at least 220 mm thick. The mortar shall be a mix of 1:3 cement to sand ratio. In-situ concrete shall be at least 150 mm thick of C35A concrete mix. The foundation and floor shall be constructed of concrete, at least 150 mm thick of C30 concrete mix on an approved compacted base to avoid settlement. All internal faces of the septic tank should be coated with sulphate resisting materials or approved product to prevent corrosion due to hydrogen sulphite or acid attacks. Where the water table is high, proper measures shall be provided to prevent infiltration and exfiltration situations.



Where bricks are used to construct septic tanks, the following additional conditions shall apply:



a)



b)

Septic Tanks

the depth of a 220 mm thick brick wall tank shall not exceed 1500 mm below ground surface, and

the depth of a 300 mm thick brick wall shall not exceed 2000 mm below ground surface.

Volume 5

25

Design Guide



Where septic tanks are of precast units, all internal surface shall be coated with sulphate resisting material or approved product or epoxy coating materials.



In cases where the septic tank may be subjected to traffic load or other surcharges, such as those installed in industrial development, the tank shall be of reinforced concrete design with Engineers approval. In the case of the proprietary type septic tanks, strict adherence to the manufacturers specification must be observed.

3.3.8

Principal Dimensions for Cast In-situ Septic Tank



The principal dimensional requirements for cast in-situ septic tanks are shown in Table 3.2 Table 3.2 Cast In-situ Septic Tank Dimensions Requirement

Dimensions

Liquid depth

Between 1.22 and 2.6 m

Minimum width

815 mm

Length : Width ratio for rectangular tanks

1.5:1

Minimum free board

250 mm

Ventilation air space

150 - 300 mm above top water level

Minimum clear sludge depth

100 mm

Minimum pipe diameter

100 mm

Surface area : depth ratio

Not less than 3 for any compartment

Maximum depth from ground level

Not exceed 4.0 m



Service chamber or extended system’s opening on top of tank need to be constructed to control or limit the depth from ground level not exceeding 3 m.

3.3.9

Principle Dimensions for Prefabricated Septic Tanks



The principal dimensional requirements for prefabricated septic tanks are shown in Table 3.3.

26

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide

Table 3.3 Prefabricated Septic Tank Dimensions Requirement

Dimensions

Minimum inlet & outlet pipe diameter

100 mm

Minimum free board

250 mm

Minimum ventilation pipe/ventilation duct size

50 mm

Minimum diameter for cylindrical tank

1.3 m

Length : Width ratio for rectangular tank

1.5 : 1

Maximum depth from ground level

Not exceed 4.0 m

Maximum tank height

Not to exceed 3.0 m



Service chamber of extended system’s opening on top of tank need to be constructed to control or limit the depth from ground level not exceeding 3.0 m.

3.4

Non-proprietary Systems



All non-proprietary septic tanks shall comply with cast in-situ septic tanks details with a minimum of 24 hours hydraulic retention time followed by a dual size media downflow filter chamber. Typical design drawings are available for two (2) categories of size; less than 12 PE and 12-30 PE are provided in Appendices H and I, respectively. These drawings shall show the critical dimensions of the septic tank as well as the stone filter chamber design.



The designer of all non-proprietary septic tanks is expected to follow the critical dimensions as depicted in these drawings for the design of both the septic tanks and filter without exception.

3.5

Proprietary Systems



A number of proprietary septic tank systems, suitable for individual premises, are available in Malaysia. These designs generally comprise of an integrated septic tank and filter in a single tank.



Only approved proprietary septic tanks from the Commission may be used. The latest list of approved proprietary septic tank systems may be obtained from the office of the Commission.



All proprietary septic tanks shall be subjected to an annual review by the Commission to evaluate its performance before qualifying to be on

Septic Tanks

Volume 5

27

Design Guide

the approved list. All tests required by the Commission shall be done in accordance with approved standards/methods.

A typical graphic presentation of prefabricated septic tank can be found in Appendix J.

3.5.1

Tank Material



a)



b)



c)



d)



The manufacturer of prefabricated septic tank shall seek prior approval on the materials to be used from the Commission and SIRIM/ IKRAM. The tank shall be made of non-degradable, non-corrodible and of inert and lightweight materials.

All fitting, pipe, partition or any other component part shall be made of non-degradable, non-corrodible and durable material that is compatible with the tank. Polyethylene tanks: -

Preferably no metal parts in the tanks.



-



Fastening of internal walls or partitions shall be done by welding or corrosion resistant fastening systems that will hold under standard testing conditions.

Glass fiber reinforced plastic:



e)



-

-

Thickness of the side walls, top, bottom, and covers shall be at least 5 mm. The thickness of the inlet and outlet ends shall be at least 3 mm and the thickness of internal walls and partitions shall be at least 1.5 mm.

Laminates shall contain not less than 30% chopped glass strands and be not less than 3 mm thick. All edges of openings and covers of the tank shall be increased to a minimum thickness of 6 mm for a minimum distance of 40 mm and shall have a minimum of 30% glass. No fillers shall be included in the laminate. The laminate thickness shall be uniform. Pigments may be allowed on the outer surfaces.



-



Reinforced precast concrete:

f)



28

-

Access opening cover and top portion of the vertical tank shall be of a minimum thickness of 4 mm, and shall have a composition of 30% glass and 70% resin. It shall also be reinforced to withstand a load of 500 kg mass.

All reinforced precast concrete septic tanks shall be capable of ing the cylinder, surface load and water tightness tests.

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide

3.5.2

Tank Fabrication and Construction



To avoid any possible leakage problem of prefabricated septic tank, the body of the septic tank below liquid level shall be fabricated or cast in seamless unit. No ts shall be allowed on the tank’s body below the liquid level.



All prefabricated septic tanks shall be fully assembled at manufacturer’s factory with QC approved. The tank shall be delivered in fully completed unit for installation at site. Any internal assembling works on the septic tank at site is not allowed to avoid any possible sub-standard assembling works of the septic tank.

3.5.3

Inspection Chamber and Septic Tank Covers



a)



b)



c)



d)



Inspection chambers shall be provided not more than 1 m before the inlet from the septic tank for maintenance purposes. The effluent pipe shall discharge immediately into an existing public drain for maintenance purposes, where applicable.



Inspection chamber shall be provided after the septic tank if the discharge point is more than 3 m or change direction of flow.

3.5.4

Ventilation, Inlet and Outlet Pipes



a)



b)



c)

Septic Tanks

Material shall be of cast iron and not other materials which, may warp over time.

The invert level of inspection chamber shall be at a minimum depth of 100 mm from the ground level but not to exceed 1000 mm. Cover dimension shall be a minimum of 600 mm x 600 mm for a rectangular opening or a diameter of 600 mm for circular opening.

Inspection chambers shall be provided immediately before and after each septic tank for maintenance purposes and where applicable.

The vent pipe shall be made of non-corrodible material, such as uPVC, to ensure corrosion does not occur when subjected to sewage gases.

The ventilation pipe should have a minimum diameter of 50 mm and shall be extended to the building/house roof top (provided with mosquitoes proof mesh or equivalent). If the septic tank is located inside a building, the vent pipe shall be located above the roof top. The vent height shall be at a minimum of 300 mm above the ridge top.

Volume 5

29

Design Guide





d)

e)

The inlet to a septic tank shall have a minimum length of 2 m.



f)



g)

All fittings through the walls of the tanks, such as the ventilation, inlet and outlet pipes, shall be installed with a permanent watertight seal.



h)

3.5.5

Filter Chamber and Filter Media



a)



b)



c)



d)



e)



f)



g)



h)

Both the inlet and outlet diameters shall be a minimum of 100 mm.

The clearance between the crown of the inlet pipe and the underside of the roof of the septic tank shall be at a minimum of 50 mm.

The invert of the outlet pipe shall be a minimum of 75 mm below the invert of the inlet pipe.

Filter media shall provide optimal surface area and texture to promote biological degradation.

The minimum surface area to volume ratio of filter media shall be a minimum of 90 m2/m3, where the surface area is referred to the total surface area of the individual particles in unit bulk volume of the filter medium when placed inside a well-packed filter chamber

A minimum opening of 600 mm x 450 mm or 600 mm diameter shall be provided over the filter media compartment.

Filter media shall preferably be of dual or more sizes instead of a single size. The filter media shall be easily accessible and removable for maintenance purposes.

The filter media shall be made of non-degradable, non-corrodible and of inert materials which may not warp over time.

The BOD 5 loading of filter chamber shall not exceed 1.2 kg/ m3.day The SS loading of filter chamber shall not exceed 1.0 kg/m3.day



i)



j)

3.5.6

Marking/Labelling



Proprietary septic tanks shall be permanently labeled with the following information:

30

The volumetric loading of filter chamber shall not exceed 2.5 m3/ m3day. The void percentage of filter chamber shall not be less than 80%. The void percentage is referred to the interstitial voids for percolation of the liquor.

Volume 5

Malaysian Sewerage Industry Guidelines

Design Guide



a) b) c) d) e) f) g)



h)



The marking or label shall be located on top of the tank close to the access opening and shall be left exposed and visible after installation.

3.5.7

Base of Septic Tank



a)



b)



c)

3.5.8

Installation



a)



b)



c)



d)



e)

Septic Tanks

Manufacturer’s name and trademark. Model of septic tank. Year of manufacture. The working capacity of the tank. The type and volume of filter media used. The minimum liquid depth of the septic tank. The symbol or logo of the certifying agency (e.g, SIRIM, ISO 9000). Permanent warning labeling advising against unauthorised entry into the tank and the word DANGER. The warning shall be located on the access opening lid.

Soil, sand or aggregates for use in bedding shall be of granular type to achieve adequate compactions.

The foundation base for septic tank must be well compacted or piled before a top concrete layer is cast in-situ, especially in high groundwater areas and for septic tanks located outdoors.

The septic tank shall sit on a well compacted sand or aggregate with a minimum of 300 mm thickness. This shall be followed by a layer of concrete on top with a minimum thickness of 100 mm and with one layer of BRC 61/BRC A9.

Careful lifting in accordance to manufacturer’s instruction is required to prevent structural failures and/or visible cracking.

Backfilling shall be conducted in layers of 250 mm thick at one a time.

During backfilling, the soil, sand or aggregates shall be uniformly filled around the tank. The practice of backfilling on one side at a time shall be avoided altogether.

Preferably, loose soil with an aggregate of not more than 30 mm shall be used for backfilling and bedding.

Septic tanks shall be anchored or strapped to the base of the concrete slab prior to backfilling, to resist floating.

Volume 5

31

Design Guide

3.5.9

Testing of Septic Tanks



a)

Care shall be exercised to prevent damage during testing.

c)

All liquid inside the septic tank shall be completely pumped out and an observation be made. If the tank fails in the buoyancy test due to upthrust pressure or is distorted due to lateral pressure, the septic tank shall be rejected. The failed tank shall be removed and replaced with a new septic tank. The reinstalled septic tank shall then be retested.





32

b)

The septic tank shall be water proofed and checked against leakage.

Volume 5

Malaysian Sewerage Industry Guidelines

Section 4 Septic Tanks Located in Sensitive Receiving Watercourses

Septic Tanks Located in Sensitive Receiving Watercourses

4.1

General



According to the Environmental Quality Act (EQA), sewage discharges upstream of water catchment areas shall be treated to meet Standard A water quality parameters. Also, where sewage is discharged into certain sensitive receiving water courses such as bathing beaches, lakes or aquaculture, farming, etc., additional treatment process may be required following the septic tank treatment.



Experience has shown that in most developed countries, where septic tanks are used; it is always followed by further treatment methods to improve the water quality prior to its ultimate disposal into surface or groundwaters. This is due to the inherent performance limitation of septic tanks in providing only primary sewage treatment. For these reasons, if septic tanks are used as a stand-alone unit process, it will NOT perform to achieve an effluent quality better than Standard B.



In these situations where an effluent quality better than Standard B is required, the Commissioner may at his discretion impose additional treatment process following septic tank treatment, including the need for disinfection. Also, due to a higher level of sophistication required for improving the treated effluent quality, the submission of these treatment systems must be certified by a ed professional engineer.

4.2

Further Treatment Methods for Achieving Higher Effluent Quality



Experience existed overseas with further treatment methods following septic tank for achieving higher effluent quality prior to its final disposal. In Malaysia, the use of these types of treatment is virtually non-existent and very little experience in the design, construction, and operation are available locally.

Hence, the proponents of such treatment methods, prior to its implementation, shall demonstrate through the design and actual operational data, that the proposed treatment methods are able to comply with the required effluent standards on a consistent basis. Further, the implementation and approval of such a system shall be subjected to a comprehensive review by the Commission on a case by case basis.

Some examples of further treatment methods following septic tank treatment which have found common usage and success are as follows:



a)

Septic Tanks

Soil Absorption System (See Appendix K and L for a typical sample) Volume 5

35

Septic Tanks Located in Sensitive Receiving Watercourses



b) c)



Proponents and designers who are keen to pursue how, when, and where to design such a system, may consult a list of references as provided in Appendix N.



Careful considerations must be given prior to the selection of the most appropriate treatment methods for adoption in each development due to the large area requirements to install such a system.



An example of such a development that may accommodate these further treatment systems would be a homestead with an average housing density of less than five (5) units per hectare. A typical layout of such an installation in a homestead development is as depicted in Appendix O.

4.3

Disinfection



The need for disinfection shall be at the discretion of the Commission on a case by case basis.



Appendix P provides the design guidelines for disinfection requirements.

36

Intermittent Sand Filter (see Appendix M for a typical sample) Small Package Mechanical Plants

Volume 5

Malaysian Sewerage Industry Guidelines

Appendix A to O

Appendix Appendix

Appendix A: Recommended Population Equivalent

Number of each similar use

1

Population for treatment

Building use

Participation in gathering place facilities

Estimation formula

a

Public assembly hall, assembly hall, theatre, cinema house, ad entertain

n = 0.08 A

b

Cycling stadium, racecourse, and motorboat racecourse

n = 16 C

c

Stand, and gymnasium

n = 0.065 A

a

Dwelling house

n = 5 +(A - 100) 30

Estimation unit n: A: n:

Participation in housing facilities

b

total number of toilet stools (piece)

A:

total floor area (m2) population (man) However, n per unit dwelling is 3.5 or 2 men [limited to a case where unit dwelling is composed of only one living room (2)] for not more than 3.5 men in n per unit dwelling and is 6 men for not less than 6 men in n per unit dwelling

c

Lodging house, and dormitory

n = 0.07 A

d

School dormitory, Self-Defence Forces camping dormitory, old-age house, and protective institution

n=P

a 3

4

5

Participation in lodging facilities

Participation in medical facilities

Participation in shops

n = 0.05 A

Apartment - house

Hotel , and RYOKAN (Japanese) (Japanese Hotel)

For that with a wedding hall or a banquet hall

n = 0.15 A

For that without any wedding hall or banquet hall

n = 0.075 A

b

Motel

n=5R

c

Public lodging house, boarding house, youth hostel, and SEINEN NO IE (Japanese) (housing for young people)

n=P

a

Hospital, sanatorium, and in-fectious hospital

For that equipped with kitchen equipment for business use or laundry facilities

For under 300 beds

n=8B

For not less than 300 beds

n = 11.43 (B 300) + 2400

For under 300 beds For not less than 300 beds

For that without any kitchen equipment for business use or laundry facilities

n=5B

n = 0.19 A

Dispensary, and doctor's office

a

Shop, and market

n = 0.075 A

b

Department store

n = 0.15 A

d

Eating house

population (man) total floor area (m2) population (man) However, n is 5 men for not more than 100 m2 in A and 10 men for over 220 m2 in A .

A:

total floor area (m2)

n: A: n:

population (man) total floor area (m2) population (man)

P:

fixed capacity (man)

n : population (man)

A:

total floor area (m2)

n: R: n:

population (man) number of guest rooms population (man)

P:

fixed capacity (man)

n : population (man) number of beds (bed)

A:

n = 7.14 (B -300) + 1500

b

c

total floor area (m2) population (man)

C(1): n: A: n:

n:

2

population (man)

For general case

n = 0.72 A

For high staining load

n = 2.94 A

For low staining load

n = 0.55 A

n:

population (man)

A :

total floor area (m2)

n:

population (man) total floor area (m2)

A:

n = 0.80 A

Teahouse

Septic Tanks

Volume 5

39

Septic Tanks

Volume 5

27

Appendix Appendix

Number of each similar use

Appendix A: Recommended Population Equivalent (cont.) a

6

Population for treatment

Building use

Participation in amusement facilities

Estimation formula

Estimation unit

n = 0.075 A

Billiard room, and table tennis room

b

Pinball house

n = 0.11 A

c

GO club, and mar-jongg saloon

n = 0.15 A

d

Discotheque

n = 0.50 A

e

Golf practice range

n = 0.25 S

f

Bowling alley

n = 2.50 L

g

Batting practice range

n = 0.20 S

h

Tennis Court

For that equipped with night game facilities For that without any night game facility

n=3S

n:

population (man)

A : total floor area (m2)

n:

population (man)

n:

population (man) number of lanes (lane)

n:

population (man) number of batting seats (seat)

n:

population (man)

S : number of driving seats L :

S :

S : number of courts (court) n=2S n:

i

population (man)

C (2) : total number of toilet stools

n = 16 C

Recreation ground and bathing resort

(piece) n: C : j

n = 20 C + 120 U x t

Pool and skating rink

8

population (man) number of closet bowls (piece)

U (3): number of urinals (piece) t : one day average use time per unit toilet stool (hour)

t = 1.0 to 2.0 k

Camp site

n = 0.56 P

l

Golf course

n = 21 H

a

Service Area

7

n:

population (man)

n:

population (man) number of squares (square)

P : n = 1.50 P

Stand Participation in parking area

population (man) number of persons to be itted (man)

H : number of holes (hole)

n = 6.15 P

Lavatory

n:

P :

n:

population (man) number of closet bowls (piece)

C : b

n = 20 C + 120 U x t

Parking area and garage

8

3

U ( ): number of urinals (piece) t : one day average use time per unit toilet stool (hour) t =0.4 to 2.0

8

Participation in school facilities

c

Gasoline stand

n = 20

a

Nursery school, kindergarden, primary school and middle school

n = 0.25 P

b

High school, university and college and miscellanous schools

n = 0.31 P

c

Library

n = 0.08 A

n:

population (man) per unit business place

n:

population (man)

P : fixed capacity (man) n:

population (man)

A : total floor area (m2)

40

Volume 5

Malaysian Sewerage Industry Guidelines

28

Volume 5

Malaysian Sewerage Industry Guideline

Appendix Appendix

Number of each similar use

Appendix A: Recommended Population Equivalent (cont.)

9

Participation in office

10

Participation in workshop

11

Population for treatment

Building use

Participation which do not belong to s of 1 to 10

a

Office

a

Factory, workshop, laboratory and ex-perimental station

(2)

(3)

For that with kitchen equipment for business use

n = 0.075 A

For that with kitchen equipment for business use For that without any kitchen equipment for business use

Estimation unit n:

population (man)

A : total floor area (m2)

For that without any kitchen equipment for business use n = 0.06 A n = 0.75 P

n:

population (man)

A : total floor area (m2) n = 0.30 P

a

Market

n = 0.02 A

b

Public bath house

n = 0.17 A

c

Public lavatory

n = 16 C

n : population (man) A : total floor area (m2) n:

population (man)

C (2) : total number of toilet stools (piece)

d

Note: (1)

Estimation formula

Station, and bus terminal

For P < 100 000

n = 0.008 P

For 100 000 < P < 200 000

n = 0.010 P

For 200 000 < P

n = 0.013 P

n:

population (man)

P : number of engers getting on and off (man/day)

Total number of toilet stools is total sum of the number of closet bowls, the number of urinals and the number of double use toilet stools The living room herein, which is the living room specified by the definitions of Building Standard Law, means a room continuously used for the purpose of dwelling, execution of one's bussiness, operation, meeting, pleasure or the like. However, a kitchen and a dining room in apartment house are excepted. In a lady exclusive use lavatory, about one half of the number of toilet stools are considered urinals.

(Source: Japanese Industrial Standard, JIS A 3302-1998 Estimation of Population for Wastewater Purifier of Buildings)

Septic Tanks

Volume 5

41

Septic Tanks

Volume 5

29

Appendix

Appendix B: Effluent Discharge Standards To Malaysian Inland Waters

Appendix

The Environmental Quality Act (EQA) 1974 specifies two standards for effluent Appendix B: Effluent Standards to Malaysian Inlandand Waters discharge. Standard A for Discharge discharge upstream of any raw water intake Standard B for discharge downstream of any raw water intake.

The Environmental Quality Act (EQA) 1974 specifies two standards for effluent discharge: Standard A for discharge upstream of any raw water intake and Standard B Thedischarge current downstream Third Schedule the Environmental Quality Act 1974, under the for of anyofraw water intake.

Environmental Quality (Sewage and Industrial Effluents) Regulations, 1979, regulations 8(1),8current (2) and 8 (3) has been and the Department Environment has The Third Schedule of revisited the Environmental Quality Actof 1974, under the th Environmental Quality (Sewage and Industrial 1979, regulations proposed 8 Schedule for the act which Effluents) stipulate Regulations, effluent discharge limits for 8parameters (1), 8 (2) specific and 8 (3)tohas been revisited and the Department of Environment has8th domestic wastewater. The effluent discharge limits in th Schedule for the Act which stipulate effluent discharge limits for proposed 8 Schedule are summarized in Table below. All sewage treatment plants design shall parameters specific to domestic thwastewater. The effluent discharge limits in 8th take into consideration of the 8 Schedule and shall comply with the proposed Schedule are summarised in Table 3.2. All sewage treatment plants design shall take limits. into consideration of the 8th Schedule and shall comply with the proposed limits. Design Effluent Values Table - Design Effluent Values Effluent Discharge to Stagnant Water Bodies*

Effluent Discharge to Rivers / Stream Parameter Standard A Absolute

Design

BOD5

20

SS

50

COD AMN Nitrate Nitrogen Total Phosphorus O&G

ℓ 5

Standard B

Standard A

Absolute

Design

Absolute

Design

10

50

20

20

20

100

40

50

120

60

200

100

10

5

20

20

10

N/A

Standard B Absolute

Design

10

50

20

20

100

40

120

60

200

100

10

5

2

5

2

50

20

10

5

10

5

N/A

N/A

N/A

5

2

10

5

2

10

5

5

2

10

5

Notes: Notes: NA = Not Applicable NAvalues = Not applicable All in mg/l unless otherwise stated. valuesWater in mg/ℓ unless otherwise stated. *All Stagnant Bodies refer to enclosed water bodies such as lakes, ponds and slow moving watercourses where dead zonerefer occurto enclosed water bodies such as lakes, ponds and * Stagnant Water Bodies

slow moving watercourses where dead zone occur.

42

Volume 5

Malaysian Sewerage Industry Guidelines

Appendix Appendix

Appendix C : Typical Layout Using Rear Access (Bungalow and Factory)

Front road

Front access

5

Bungalow/Factory 2

4 2 1

3

Legends :

Septic tank

Roadside drain Property boundary (fence)

Rear access Effluent to roadside drain

Backlane

Effluent to roadside drain

Rear access

Septic tank

1 2

Gate Inspection Chamber

Minimum width at 4.5m

1 2 3 4 5

Toilet Bath Kitchen sink Wash room Shower

3

4 5

Bungalow/Factory 1

Front access

Front road

Septic Tanks

Volume 5

Septic Tanks

Volume 5

43

31

RA

44

Volume 5

32

Volume 5 FA

FA

Frontal road

2

ST

1

ST

RA

Effluent to roadside drain

RA

Backlane

FA

3

ST

ST

FA

4

RA

Minimum width at 4.5m

RA

FA

1, 2, 3, 4

ST

Terrace House/Shop House Commercial Buildings/Property Front Access Rear Access

Gate

Inspection chamber

Septic tank

Roadside drain Property Boundary (fence)

Legends :

Appendix Appendix

Appendix D : Typical Layout Using Rear Access (Terrace House, Shop House and Commercial Building)

Malaysian Sewerage Industry Guidelines Malaysian Sewerage Industry Guideline

ST

1

Septic Tanks

Septic Tanks FA

RA

RA

Volume 5

Volume 5

Frontal road

FA

2

Backlane

ST

RA

FA

1, 2

ST

Terrace House/Shop House Commercial Buildings/Property Front Access Rear Access

Gate

Inspection chamber

Septic tank

Roadside drain Boundary line

Legends :

Appendix Appendix

Appendix E : Typical Layout Using Front Access (Bungalow, Terrace House, Shop House and Commercial Building)

45

33

Appendix

46

Volume 5

Malaysian Sewerage Industry Guidelines

Appendix Appendix

Appendix G : Details Showing By to Public Sewer

600 mm Ø manhole Brickwork with cast iron manhole cover

A 100 mm Ø UPVC inlet pipe from WC

100 mm Ø UPVC pipe from WB/FT sink

300 x 300 mm grease trap

600 x 600 mm outlet manhole

600 x 600 mm inlet manhole 100 mm Ø UPVC outlet pipe

150 mm Ø V for future connection

Road side drain

Rubber plug

Plan Inlet manhole

Building boundary

A

Ground beam Top water level

UPVC inlet pipe Road side drain 300 Min Rubber plug

150 mm Ø V for future connection

Rubber plug

150mm concrete surround

Section A - A

Septic Tanks

Volume 5

Septic Tanks

Volume 5

47

35

Appendix

48

Volume 5

Malaysian Sewerage Industry Guidelines

Appendix

Septic Tanks

Volume 5

49

Appendix Appendix Appendix J – Typical detail of a proprietary septic tank

600mm O / 450x600mm airtight cover & frame

min. 250mm O cast iron manhole cover & frame

ground level

200

brickwork extension

300 min.150

removable filter media

min. 100mm outlet pipe screwed type filter chamber cover

sand backfilling filter chamber

min. 150mm

working volume HRT (min. 24 hours)

stainless steel anchor strape grade 304

7.5mm

TWL

min. 900mm max. 2400mm (liquid depth)

max. 3000mm

min. 100mm inlet pipe

m in. 1300mm

min. 500mm max. 2/3 d

250mm freeboard

50mm ventilation pipe to roof top

min. 100, max. 600

ground level

sludge generation capasity (for 2 years)

150 thk. grade 30N conc. base with 1 layer of BRC A9 to suit ground condition 50 thk. lean concrete Legend : working volume sludge generation capacity

Typical Pre Fabricated Septic Tank for < 600mm depth

filter media

a) for < 600 mm depth

chequer plate cover m ax w eight - 16kg/piece

brickw ork extension airtight cover 2 00 7.5mm

rem ovable filter m edia

w orking volum e H R T (m in. 24 hours)

m in. 100m m outlet pipe scre w ed type filter cham ber cover

sand backfilling filter cham ber

min. 150mm

stainless steel ancho r strape grade 304

TW L

min. 500mm max. 2/3 d

max. 3000mm

m in. 100m m inlet pipe

m in . 13 00m m

min. 900mm max. 2400mm (liquid depth)

300 min.150

250mm freeboard

50m m ventilation pipe to roof top

ground level

min. 600, max. 1000

g ro und level

sludge generation capasity (for 2 years)

150 thk. grade 30N conc. base w ith 1 layer of B R C A9 to suit ground condition 5 0 thk. lean concrete Legend : w orking volum e sludge generation capacity

T ypical P re Fabricated S eptic T ank for > 600m m depth

filte r m edia

b) for > 600 mm depth 50 38

Volume 5 Volume 5

Malaysian Sewerage MIndustry alaysian SGuidelines ewerage Industry Guideline

Septic Tanks

Septic Tanks

Volume 5

Volume 5 600 - 1200 mm

900 - 1800mm

900 - 1800mm

TYPICAL BED SYSTEM

Water Table or Creviced Bedrock

Barrier Material

Distribution Box

150 - 300mm of 20 - 60mm dia. rock

Perforated Distribution pipe

Appendix Appendix

Appendix K : Typical Bed System for Soil Absorption

51

39

Appendix Appendix

Appendix L : Typical Mound System for Soil Absorption

C ap S tra w , H a y or Fabric

D is trib u tio n Lateral

F ill A bs orptio n B ed

T o p s oil

1 3 P lo w e d L a y e r of Top Soil S lo pe

R o c k S tra ta o r Im p e rm eable Soil Layer

(a ) C r o s s S e c tio n o f a M o u n d S ystem for S low ly P erm eable S o il o n a sloping site

S tra w , H a y or Fabric

C ap

D is trib u tio n Lateral

F ill

A bs orptio n B ed

T o p s oil

3

1 P lo w e d L a y e r of Top Soil P e rm e a b le Soil

W a te r T a b le o r C r e v iced B edrock (b ) C r o s s S e c tio n o f a m o u n d S ystem for a P erm eable S oil, w ith H ig h G r o u d W a te r o r S hallow C reviced B edrock

52

Volume 5

40

Volume 5

Malaysian Sewerage Industry Guidelines Malaysian Sewerage Industry Guideline

Appendix Appendix

Appendix M – Typical Buried Intermittent Sand Filters for Effluent Polishing Vent Pipe

Vent Pipe A

Distribution box

House Sewer

Septic Tank with Filter

Discharge

Inspection manhole

A

Inspection Manhole and Disinfection Tank (if required)

Plan

Top Soil Fill Drain

age

Marsh Hay or drainage fabric

Perforated or Open t Distributors

Graded Gravel 20-60mm diameter

Filter Media

Pea Gravel

Perforated or Open t pipe, Tarpaper over open ts

Graded Gravel 6-40mm

SECTION A-A

Septic Tanks

Volume 5

53

Septic Tanks

Volume 5

41

Appendix Appendix

Appendix N : List of Reference on Further Treatment Methods Otis, RJ, WC Boyle, EV Clements and CJ Schmidt, 1980. Design Manual : On-Site Wastewater Treatment and Disposal Systems. Report No. EPA-625/1-80-012, 412 pp. Environmental Protection Agency, Washington DC 20460. Brouver, J and RM Bugeja, 1983, Land capability for septic tank effluent absorption fields. Australian Water Resources Council Tech. Paper No. 80 Australian Government Publishing Service, Canberra. Carbon, BA and MA Murray, 1980. Domestic septic tanks near Perth : Expected life of effluent disposal systems. Water, Journal of the Australian Water and Wastewater Association. Vol. 7 No. 2 p21-2. Day, KJ and ST Willatt, 1982. Evapotranspiration as a method of on-site wastewater disposal in Victoria. Published by the school of Agriculture, La Trobe University, Bandoora, Victoria. Household Wastewater Treatment Committee. Septic Tanks Code of Practice, January 1990. Department of Water Resources, Victoria. U. S. Department of Healthy, Education, and Welfare. Manual of Septic Tank Practice, 1967. Bureau of Disease Prevention and Environmental Control. National Center of Urban and Industrial Health, Cincinnati, Ohio 45202.

54

Volume 5

42

Volume 5

Malaysian Sewerage Industry Guidelines Malaysian Sewerage Industry Guideline

Appendix Appendix

Appendix O : Typical Layout for Homestead Unit with Septic Tank & Further Treatment Facilities

FA Front Access

House

Septic Tank & Further Treatment Facilities

Septic Tanks

Septic Tanks

Volume 5

Volume 5

55

43

PRINTED BY PERCETAKAN NASIONAL MALAYSIA BERHAD KUALA LUMPUR, 2009 www.printnasional.com.my email: [email protected] Tel: 03-92366895 Fax: 03-92224773