Sharp Mx M550n U Mx M620n U Mx M700n U 6io1k

SERVICE MANUAL CODE: 00ZMXM700/S2E

DIGITAL MULTIFUNCTIONAL SYSTEM

MX-M550N/M550U MX-M620N/M620U MODEL MX-M700N/M700U CONTENTS NOTE FOR SERVICING [1] PRODUCT OUTLINE . . . . . . . . . . . 1-1

● DETAILS OF EACH SECTION

[2]

SPECIFICATIONS . . . . . . . . . . . . . 2-1

[B] OPERATION . . . . . . . . . . . B -1

[3]

CONSUMABLE PARTS . . . . . . . . . 3-1

[C] DSPF SECTION . . . . . . . . . . . . . . . C -1

[4]

UNPACKING AND INSTALLATION

[D] SCANNER SECTION . . . . . . . . . . . D -1

* For unpacking and installation, refer to the installation manual (00ZAR700//I1E).

[E] MANUAL PAPER FEED SECTION. . E -1

[5]

EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . . . . . . 5-1

[G] PAPER TRANSPORT SECTION . . G -1

[6]

ADJUSTMENTS . . . . . . . . . . . . . . . 6-1

[H] DUPLEX SECTION . . . . . . . . . . . . H -1

[7]

SIMULATION . . . . . . . . . . . . . . . . . 7-1

[ i]

LSU SECTION . . . . . . . . . . . . . . . . i -1

[8]

SELF DIAG AND TROUBLE CODE . 8-1

[J]

PHOTOCONDUCTOR SECTION. . J -1

[9]

MAINTENANCE . . . . . . . . . . . . . . . 9-1

[K] TONER SUPPLY SECTION . . . . . . K -1

[A] EXTERNAL OUTFIT . . . . . . . . . . . . A -1

[F] TRAY PAPER FEED SECTION . . . F -1

[10] ROM VERSION-UP . . . . . . . . . . . .10-1

[L]

DEVELOPING SECTION . . . . . . . . L -1

[11] ELECTRICAL SECTION. . . . . . . . . 11-1

[M] TRANSFER SECTION . . . . . . . . . . M-1

[12] OTHERS . . . . . . . . . . . . . . . . . . . . .12-1

[N] FUSING SECTION . . . . . . . . . . . . . N -1 [O] PAPER EXIT SECTION . . . . . . . . . O -1 [P] DRIVE SECTION . . . . . . . . . . . . . . P -1 [Q] PWB SECTION. . . . . . . . . . . . . . . . Q -1 [R] FAN AND FILTER SECTION . . . . . R -1 [S] SENSOR, SWITCH SECTION . . . . S -1

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used for after sales service only. The contents are subject to change without notice.

CONTENTS

● DETAILS OF EACH SECTION

NOTE FOR SERVICING 1. Precautions for servicing . . . . . . . . . . . . . . . . . . . . . . . . i 2. Warning for servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . i 3. Installing site recommendations . . . . . . . . . . . . . . . . . . . i

[A] EXTERNAL OUTFIT . . . . . . . . . . . . . . . . . . . . . . . . .

A- 1

[B] OPERATION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . .

B- 1 B- 2 B- 2

[1] PRODUCT OUTLINE 1. Different points of MX-M550/620/700 series from AR-M550/620/700 series . . . . . . . . . . . . . . . . . . . 2. Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . .

1111-

1 1 1 4

[2] SPECIFICATIONS 1. Basic specifications . . . . . . . . . . . . . . . . . . . . . . . 2. Functional specifications. . . . . . . . . . . . . . . . . . . . 3. Environmental conditions.. . . . . . . . . . . . . . . . . . .

[C] DSPF SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CCCC-

1 5 6 19

2- 1 2- 4 2- 11

[3] CONSUMABLE PARTS 1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . 2. Maintenance parts list . . . . . . . . . . . . . . . . . . . . . .

3- 1 3- 2

[D] SCANNER SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DDDD-

1 2 4 11

[E] MANUAL PAPER FEED SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

E E E E

-

1 2 2 8

[F] TRAY PAPER FEED SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F F F F

-

1 5 8 17

[G] PAPER TRANSPORT SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GGGG-

1 5 5 14

[H] DUPLEX SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HHHH-

1 2 4 12

[ i ] LSU SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . .

i - 1 i - 2 i - 2

[J] PHOTOCONDUCTOR SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

J J J J

-

1 3 4 9

[K] TONER SUPPLY SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

K K K K

-

1 2 3 4

[L] DEVELOPING SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

L L L L

-

1 2 2 5

[M] TRANSFER SECTION 1. Electrical and mechanism relation diagram . . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MMMM-

1 2 3 5

[4] UNPACKING AND INSTALLATION * For unpacking and installation, refer to the installation manual (00ZAR700//I1E). [5] EXTERNAL VIEW AND INTERNAL STRUCTURE 1. Identification of each section and functions . . . . .

5- 1

[6] ADJUSTMENTS 1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Adjustment item list. . . . . . . . . . . . . . . . . . . . . . . . 4. Datails of adjustment . . . . . . . . . . . . . . . . . . . . . .

6666-

1 1 1 2

[7] SIMULATION 1. Adjustment value/Simulation and storage data. . . 2. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. List of simulation codes . . . . . . . . . . . . . . . . . . . . 4. Details of simulation . . . . . . . . . . . . . . . . . . . . . . .

7777-

1 2 4 8

[8] SELF DIAG AND TROUBLE CODE 1. Self diag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Trouble code list . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Details of trouble code . . . . . . . . . . . . . . . . . . . . .

8- 1 8- 4 8- 6

[9] MAINTENANCE 1. Maintenance system table . . . . . . . . . . . . . . . . . . 2. Details of maintenance . . . . . . . . . . . . . . . . . . . . . 3. Other related items . . . . . . . . . . . . . . . . . . . . . . . .

9- 1 9- 4 9- 13

[10] ROM VERSION-UP 1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Necessary items for Flash ROM version-up . . . . . 4. Flash ROM version-up method . . . . . . . . . . . . . . . 5. Turning OFF the power during the version-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Version-up procedure flowchart . . . . . . . . . . . . . . [11] ELECTRICAL SECTION 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Power line chart . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Actual wiring chart . . . . . . . . . . . . . . . . . . . . . . . . 4. Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . .

10101010-

1 2 2 2

10- 5 10- 5 11 11 11 11 -

1 5 8 18

[12] OTHERS 1. System settings . . . . . . . . . . . . . . . . . . . . . . . . . . 12- 1 2. Web setting service mode. . . . . . . . . . . . . . . . . . . 12- 8 3. Paper JAM code . . . . . . . . . . . . . . . . . . . . . . . . . . 12- 10

CONTENTS

[N] FUSING SECTION 1. Electrical and mechanism relation diagram . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NNNN-

1 2 3 12

[O] PAPER EXIT SECTION 1. Electrical and mechanism relation diagram . . . . 2. Operational descriptions . . . . . . . . . . . . . . . . . . . 3. Disassembly and assembly . . . . . . . . . . . . . . . . 4. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OOOO-

1 2 2 7

[P] DRIVE SECTION 1. Disassembly and assembly . . . . . . . . . . . . . . . . 2. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

P- 1 P - 14

[Q] PWB SECTION 1. Disassembly and assembly . . . . . . . . . . . . . . . .

Q- 1

[R] FAN AND FILTER SECTION 1. Disassembly and assembly . . . . . . . . . . . . . . . . 2. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R- 1 R- 6

[S] SENSOR, SWITCH SECTION 1. Disassembly and assembly . . . . . . . . . . . . . . . .

S- 1

MX-M700N

NOTE FOR SERVICING

4) When connecting the grounding wire, never connect it to the 5GTXKEG/WCN following points.

This Service Manual uses some symbols to assure safe operation. Please understand the meanings of photographs before servicing.

It may cause an explosion, a fire or an electric shock. • Gas tube • Lightning conductor

WARNING: If this WARNING should be ignored, a serious danger to life or a serious injury could result. CAUTION: If this CAUTION should be ignored, an injury or a damage to properties could result.

• A water pipe or a water faucet, which is not recognized as a grounding object by the authorities. • Grounding wire for telephone line 5)

Do not put heavy objects on the power cable. Do not bend it forcibly or do not pull it extremely.

1. Precautions for servicing 1)

It may cause a fire or an electric shock.

When servicing, disconnect the power plug, the printer cable, the network cable, and the telephone line from the machine, except when performing the communication test, etc. It may cause an injury or an electric shock.

2)

Do not damage, break, or work the power cord.

There is a high temperature area inside the machine. Use an extreme care when servicing. It may cause a burn.

6)

Keep the power cable away from a heat source. Do not insert the power plug with dust on it into a power outlet. It may cause a fire or an electric shock.

7)

Do not put a receptacle with water in it or a metal piece which may drop inside the machine.

8)

With wet or oily hands, do not touch the power plug, do not insert the telephone line jack, do not operate the machine, or do not perform servicing.

It may cause a fire or an electric shock.

3)

There is a high voltage section inside the machine which may cause an electric shock. Be careful when servicing.

4)

Do not disassemble the laser unit. Do not insert a reflective material such as a screwdriver in the laser beam path.

5)

When servicing with the machine operating, be careful not to squeeze you hands by the chain, the belt, the gear, and other driving sections.

3. Installing site recommendations

6)

Do not leave the machine with the cabinet disassembled.

1)

It may cause an electric shock.

It may damage eyes by reflection of laser beams.

Do not install the machine at the following sites.

Do not allow any person other than a serviceman to touch inside the machine. It may cause an electric shock, a burn, or an injury. 7)

Paper may get damp and form dews inside the machine, causing paper jam or copy dirt.

When servicing, do not breathe toner, developer, and ink excessively. Do not get them in the eyes.

For operating and storing conditions, refer to the specifications described later.

If toner, developer, or ink enters you eyes, wash it away with water immediately, and consult a doctor if necessary. 8)

The machine has got sharp edges inside. Be careful not to damage fingers when servicing.

9)

Do not throw toner or a toner cartridge in a fire. Otherwise, toner may pop and burn you.

Place of high temperature, high humidity, low temperature, low humidity, place under an extreme change in temperature and humidity.

10) When replacing the lithium battery of the PWB, use a specified one only. If a battery of different specification is used, it may be broken, causing breakdown or malfunction of the machine. 11) When carrying a unit with PWB or electronic parts installed to it, be sure to put it in an anti-static-electricity bag.

2)

Places of too much vibrations It may cause a breakdown.

It may cause a breakdown or malfunctions.

2. Warning for servicing 1)

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Avoid complex wiring, which may lead to a fire or an electric shock. It may cause a fire or an electric shock.

2)

If there is any abnormality such as a smoke or an abnormal smell, interrupt the job and disconnect the power plug.

3)

Be sure to connect the grounding wire. If an electric leakage occurs without grounding, a fire or an electric shock may result.

It may cause a fire or an electric shock.

To protect the machine and the power unit from lightening, grounding must be made.

MX-M700N NOTE FOR SERVICING - i

3)

Poorly ventilated areas

7)

An electro-static type copier will produce ozone inside it.

Place too close to a wall All machines require clean intake and exhaust of air. If the intake and exhaust of air are not proper, failure of the machine will occur.

The quantity of ozone produced is designed to a low level so as not to affect human bodies. However, continuous use of such a machine may produce a smell of ozone. Install the machine in a well ventilated place, and ventilate occasionally.

11-13/16" (30cm) 6-1/8" (15cm)

23-5/8" (60cm)

8) 4)

Place of direct sunlight.

Placement of the machine will affect performance.

Plastic parts and ink may be deformed, discolored, or may undergo qualitative change.

An unstable machine may fall over and cause an injury.

It may cause a breakdown or copy dirt.

5)

Unstable or uneven surfaces

Use the proper optional desk unit. When using the optional desk, be sure to lock the adjusters and casters.

Place which is full of organic gases such as ammonium The organic photoconductor (OPC) drum used in the machine may undergo qualitative change due to organic gases such as ammonium. Installation of this machine near a diazo-type copier may result in dirt copy.

6)

Place of too much dust When dust enters the machine, it may affect the operation of the machine.

MX-M700N NOTE FOR SERVICING - ii

MX-M700N [1] PRODUCT OUTLINE

(2) Strengthened Frame Structure 5GTXKEG/WCN

1. Different points of MX-M550/620/700 series from AR-M550/620/700 series

Improved stability with less machine distortion, and both rigidity and



Highly Rigid Frame lightweight been achieved.

(3)

• Adopted new operation with 8.9 inch LCD

Energy Saving with Unique External Heat Roller Fusing System

• Added web roller and motor for web roller in Fusing section

Newly Developed External Heating System

• Added firmware version-up using USB device by Sim 49-1

1)

High reliability with stabilized fusing ability

• Eliminated parallel port

2)

Shortened warm up time before start copying

3)

Achievement of energy efficiency that clears 2006 Rationalization in Energy Use Law

2. Main Features

External Heat Roller Fusing System

A. Single Duplex Scanner • Max. 76 m for duplex scanning • Best-in-class 150-sheet feeder

Thin Steel Fusing Roller

B. Security Solution Data encryption + data clear with random number

Low Heat Capacity Rubber Roller

• Network security

C. New Toner • Higher density/Finer particles

External Heating Roller

High Efficiency Heater

D. Inner Output • Separate copy output pages from printer output pages

B. Network tandem

E. Enhance the solutions such as document filing and other features.

With Network tandem function, s can output one job on two network connected engines. Productivity of large-volume copying/ printing can be dramatically improved by high-speed output of up to 110m (55m model), 124m (62m model) and 140m (70m model).

F. Design for High Reliability • Robust frame designed by highly accurate CAE analysis

G. Improved Performance Copy

• Network Tandem Copy/Print

Scan original from document glass or DSPF

• High-speed Processor • New high-speed ASIC

H. Fax feature For replacement of mid/low speed devices (up to area)

I. Large Capacity Finisher Finisher capacity: 4,000-sheet

3. Features A. High reliability (1)

Send print data from PC

Improved Image Quality/Paper Transport

Full-Grip Path Design Stable paper feeding realized by rollers that firmly grip paper

Print

Small-Diameter Belt Transfer System With reduced effect to paper types, drum paper release is stabilized and transfer efficiency is improved Easier Paper Jam Fixation with Open Paper Path Jammed paper on vertical paper path can be easily removed by opening the left side cover, which shortens time to fix paper jam

* s can use the function simply by connecting the engines to network. This means no Tandem Kit (Connection cable) necessary.

MX-M700N PRODUCT OUTLINE 1 – 1

C. 2-Way Security Solution

ONLY-ONE

Way-in : Network Security

Print data

Allow access of authorized network address only and prevent unauthorized access from outside. (Filtering of network address)

Copy data

Print data

Scan data

Fax data

Way-out : HDD Data Clear + Encryption Data clear by plural writing random number. Cannot be analyzed even when peeped by encryption.

(1)

Data Security coexisting with Document Filing

Data Security

Document Filing/Quick File Original data HDD memory Print data Install Fax data Store Store Raw/compressed data

Recall (Job settings) PIN printing input

DSK

Document Filing/Quick File Original data Print data HDD memory Fax data Encrypt before storing Encrypted data PIN printing input

Recall (Job settings)

Security is assured by encrypting the data to be stored!

MX-M700N PRODUCT OUTLINE 1 – 2

D. Document Filing Document filing is a function that enables s to share and reuse data stored in the engine's HDD by digitalizing various information sent/scanned from printer, fax, PC or MFP that are connected by network.

G3 Fax



Internet-Fax Copy Scan

PC

Send E-mail

Print FAX

Print data

Send

PC

HDD

i-FAX

MX-M550N/U MX-M620N/U MX-M620N/U MX-M700N/U

Send E-mail

G3 Fax

Internet Fax Telephone line Network/LAN

PC Fax PC i-Fax Fax data i-Fax data

PC-Fax is like printing Word data etc. onto fax paper.

MX-M700N PRODUCT OUTLINE 1 – 3

4. CONFIGURATION A. Main unit and option lineup (1)

Option lineup

Saddle stitch finisher Punch unit

55 / 62 / 70 ppm

A4 LCC

Inserter

A3 LCC Finisher

Facsimile expansion kit Network expansion kit

Barcode font kit

FAX momory (8MB) Network scanner expansion kit

SHARPDESK 1 (5, 10, 50, 100) license kit

Application communication module

Application integration module kit

55 / 62 / 70 ppm Printer function Standard

PS3 expansion kit

256MB expansion memory board

Data security kit

MX-M700N PRODUCT OUTLINE 1 – 4

External module

Internet FAX expansion kit

(2)

Option combinations

STD: Standard provision

u : Not installable

OPT: Installable Option

Section

Paper feed system Paper exit system

Electrical system (Printer controller)

Software

FAX system

Other options

Machine model Copier model Network printer MX-M550U/ MX-M550N/ M620U/M700U M620N/M700N OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT STD STD OPT STD OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT OPT

Item Large capacity tray (AR-LC6) Large capacity tray (AR-LC7) Finisher (AR-F15) Saddle stitch finisher (AR-F16) Inserter (AR-CF2) Punch module (AR-PN4A) Punch module (AR-PN4B) Punch module (AR-PN4C) Punch module (AR-PN4D) Printer expansion kit Network expantion kit (MX-NBX1) Expansion memory (AR-SM5) PS3 expansion kit (MX-PKX1) Barcode font kit (AR-PF1) Network scanner expansion kit (MX-NSX1) Sharpdesk 1 license kit (MX-USX1) Sharpdesk 5 license kit (MX-USX5) Sharpdesk 10 license kit (MX-US10) Sharpdesk 50 license kit (MX-UX50) Sharpdesk 100 license kit (MX-USA0) Internet FAX expansion kit (MX-FWX1) Facsimile expansion kit (AR-FX8) FAX expansion memory (8MB) (AR-MM9) Application integration module kit (MX-AMX1) Application communication module (MX-AMX2) External module (MX-AMX3)

Remarks (A4 / 8.5 u 11) (A3 / 11 u 17)

(2 holes) (3 holes) (4 holes) (4 holes, wide) Yes (256MB) Yes Yes

Yes

Yes Yes Yes

B. Block diagram DSPF Unit (CIS)

Telephone Line

Operating Section

Image Scanner (reading) Section (CCD)

Fax unit (Option)

MFP Control PWB

Scanner Control PWB Engine Control Section (PCU PWB)

USB Port

Network Port

Scanner(writing) (LSU) Section Toner Bottle

HDD Drum Section Toner Hopper

Fusing Section

Transfer Section

Paper Exit and switch back Section

Developer Section

Manual Paper Feed Tray

ADU Section

Paper Transport Section

Finisher (Option)

Punch Unit (Option)

Paper Feed Tray 1

Inserter (Option)

Paper Feed Tray 2

Paper Feed Tray 3 DC Power Unit

AC Power Unit

Paper Feed Tray 4

MX-M700N PRODUCT OUTLINE 1 – 5

Product key

Large Capacity Paper Tray Unit (Option)

MX-M700N

[2] SPECIFICATIONS

5GTXKEG/WCN

1. Basic specifications A. Base engine

(8)

(1)

a. Void area/Image loss

Type

Type Copy mode

(2)

(3)

40ppm

45ppm

48ppm

OPC (Drum diameter: I80mm) Electronic photo (Laser) Dry, 2-component magnetic brush development Charged saw-tooth method Static electricity transfer (Transfer belt method) Counter blade Heat roller WEB cleaning method Toner supply by the front cover open Toner cartridge collection (No toner recycling system)

Gradation

Warmup

After turned on Pre-heat

120 seconds or less YES

Jam recovery time

Jam recovery time

Voltage Current

55 ppm 62 ppm 70 ppm

Frequency Power source code Power switch

Approx. 30 sec. (After leaving the machine with the side cover open for 60sec, in the standard condition and the polygon stop conditions.)

289 ✕ 412mm 242 ✕ 356mm 202 ✕ 289mm 174 ✕ 249mm 140 ✕ 202mm 183 ✕ 259mm 92 ✕ 140mm

11 ✕ 17 8.5 ✕ 14 8.5 ✕ 13 8.5 ✕ 11 5.5 ✕ 8.5 8K 16K

200V series 200 to 240V 8A 8A 8A

50/60Hz Dedicated outlet 2 switches (Primary switch: in the front cover; Seconday switch: on side of the main unit)

(10) Power consumption Low power consumption mode Maximum rated power consumption Reset time from low power mode Power consumption in the off mode Shift time to off mode

100V series 200V series 55 ppm : max. 261.75W 62 ppm : max. 288.7W 70 ppm : max. 319.5W 1.80KW (*)

1.84KW (*) 30 sec.

95W or less 90 min.

* : With full options

(11) Dimensions Outer dimensions

728 ✕ 679 ✕ 1050mm (Height: Floor to Glass surface) 728 ✕ 679 ✕ 1192mm (Height: Floor to SPF top) 728 (W) ✕ 679 (D) mm

(12) Weight Main unit

Approx. 185kg / 408lbs

(13) Dimensions occupied by Machine Main unit Main unit + A4-LCC installed Main unit + finisher/ Saddle finisher installed Main unit + A4-LCC + finisher/ Saddle finisher installed Main unit + Inserter + Finisher/ Saddle finisher Main unit + A4-LCC + Inserter + Finisher/Saddle finisher installed Main unit + A3-LCC installed Main unit + A3-LCC + finisher/ Saddle finisher installed Main unit + A3-LCC + inserter + finisher/ Saddle finisher installed

Printable area

A3 B4 A4 B5 A5 7.25 ✕ 10.5 Postcard

100V series 100 to 127V 16A 16A 16A

Footprint Copy : 600 ✕ 600dpi Printer: PCL: 600 ✕ 600dpi, 300 ✕ 300dpi PS : 600 ✕ 600dpi Copy: None Printer: Model of 55/62 sheets: Equivalent to1200dpi ✕ 600dpi (PCL/PS) Model of 70 sheets : None [Writing] 2 gradations

Smoothing

(7)

70ppm 70ppm 48ppm

Engine resolution

Resolution (Writing)

(6)

62ppm 62ppm 45ppm

Engine composition

Cleaning system Fusing system Fused cleaning system Toner supply method Waste toner disposal

(5)

55ppm 55ppm 40ppm

55ppm 62ppm 70ppm 40ppm 45ppm 48ppm 35ppm 39ppm 45ppm 30ppm 34ppm 39ppm 30ppm 34ppm 39ppm Since the next paper is fed after completion of paper exit outside the machine, it depends on the machine composition.

Charging system Transfer system

Lead edge: 40mm or less Rear edge: 4.0mm or less FR total : 8.0mm or less

(9) Power source

Engine speed (ppm)

Photoconductor kind Copying method Developing system

(4)

Void area/Image loss

Console Monochrome digital (Electronic photo graphic)

Paper size A4, 8.5 ✕ 11 A4R, 8.5 ✕ 11R A5R/5.5 ✕ 8.5R 5.5 ✕ 8.5-R B5 B5R, 7.25 ✕ 10.5-R B4/8.5 ✕ 14 A3/11 ✕ 17 Extra Postcard

Image defect

271 ✕ 424mm 208 ✕ 348mm 208 ✕ 322mm 208 ✕ 271mm 132 ✕ 208mm 262 ✕ 382mm 187 ✕ 262mm

MX-M700N SPECIFICATIONS 2 – 1

1264 ✕ 679 ✕ 1192mm 1340 ✕ 679 ✕ 1192mm 1797 ✕ 679 ✕ 1192mm 1873 ✕ 679 ✕ 1192mm 2079 ✕ 679 ✕ 1192mm 2155 ✕ 679 ✕ 1192mm 1660 ✕ 679 ✕ 1192mm 2193 ✕ 679 ✕ 1192mm 2475 ✕ 679 ✕ 1192mm

B. Paper feed, paper transport, and paper exit section (1)

[Paper feed section]

Type Paper feed method Dehumidification heater

(2)

4-stage paper feed tray (Parallel LCC + 2 tray + Multi manual paper feed) Paper is fed from the above by the front loading system. Service parts

Paper feed tray of the main unit

a. Tray1 (Left tray in the parallel LCC)

Paper size AB (Europe, SCA): A4, 8.5 ✕ 11 AB (Other): A4, 8.5 ✕ 11 Inch: 8.5 ✕ 11, A4 (ed by the guide change and the software setting)

Paper size change method Size setting by

Paper type setting

Paper size setting when shipping

YES

Inch: 8.5 ✕ 11 AB: A4

Allowable paper type and weight for paper feed Plain paper: 60 to 105g/m2 (16 to 28lbs)

Paper capacity (Standard paper) 800 sheets (80g/m2)

Paper type Normal paper, printed paper, recycled paper, letterhead, punched paper, color paper

Tray lift time

Paper remaining detection Enable (Paper empty and 3 steps)

Up

Down

Within 12sec (*)

Free fall

* Time required from tray insertion to empty detection when paper is empty. b. Tray2 (Right tray in the parallel LCC)

Paper size

Paper size change method

AB (Europe, SCA): A4, 8.5 ✕ 11 AB (Other): A4, B5, 8.5 ✕ 11 Inch: 8.5 ✕ 11, A4 (ed by the guide change and the software setting)

A4: can change 8.5 ✕ 11: can change B5: Size setting by serviceman (B5 available through bolt fixing and setting by serviceman)

Paper type setting

Paper size setting when shipping

YES

Inch: 8.5 ✕ 11 AB: A4 (16K is not ed)

Allowable paper type and weight for paper feed Plain paper: 60 to 105g/m2 (16 to 28lbs)

Paper capacity (Standard paper) 1200 sheets (80g/m2)

Paper type Normal paper, printed paper, recycled paper, letterhead, punched paper, color paper

Tray lift time

Paper remaining detection Enable (Paper empty and 3 steps)

Up

Down

Within 12sec (*)

Free fall

* : Time required from tray insertion to empty detection when paper is empty. c. Tray3 (multi-purpose tray)

Paper size Auto AB: A3, B4, A4, A4R, B5, B5R, A5R, 8.5 ✕ 13 Auto inch: 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 11, 8.5 ✕ 11R, 7.25 ✕ 10.5R, 5.5 ✕ 8.5R Manual: 8K, 16K, 16KR Special size :[Vertical] 139 to 297mm (5.5 to 11-5/8) [Horizontal] 139 to 431mm (5.5 to 17) (Tab paper is of A4; limited to tab width 12mm to 20mm/8.5 ✕ 11; tab width 6.1mm to 17mm.)

Paper size change method Guide adjustment by

Paper type setting YES

Paper size setting when shipping Shipped with the paper guide width at Max.

Allowable paper type and weight for paper feed Plain paper: 60 to 105g/m2 (16 to 28lbs) Thick paper: 106 to 128g/m2 (29 to 34lbs) 176g/m2 (65lbs) Cover 205g/m2 (110lbs) Index(*)

Paper capacity Normal OHP paper 500 sheets 40 (80g/m2) sheets

Paper type Normal paper, printed paper, recycled paper, letterhead, punched paper, color paper, label paper, thick paper, OHP, tab paper

Paper remaining detection Enable (Paper empty and 3 steps)

* 105g/m2 or above, A4/8.5 ✕ 11 or less. For 128g/m2 or above, horizontal feed only. d. Tray 4 (500 sheets paper feed tray)

Paper size Auto AB: A3, B4, A4, A4R, B5, B5R, 8.5 ✕ 13 Auto inch: 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 11, 8.5 ✕ 11R, 7.25 ✕ 10.5R Manual: 8K, 16K, 16KR Custom size: None

Paper size change method Guide adjustment by

Paper type setting YES

Paper size setting when shipping Shipped with the paper guide width at Max.

Allowable paper type and weight for paper feed Plain paper: 60 to 105g/m2 (16 to 28lbs) Thick paper: 106 to 128g/m2 (29 to 34lbs) 176g/m2 (65lbs) Cover 205g/m2 (110lbs)Index (*1),(*2)

* 1: 105g/m2 or above, A4/8.5 ✕ 11 or less. For 128g/m2 or above, horizontal feed only. * 2: For multi copy and back surface copy, single feed only. MX-M700N SPECIFICATIONS 2 – 2

Paper capacity (Standard paper) 500 sheets (80g/m2)

Paper type Normal paper, recycled paper, printed paper, letterhead, punched paper, color paper, thick paper

Paper empty detection Enable (Paper empty and 3 steps)

(3)

By tray Paper size

Auto AB: A3, B4, A4, A4R, B5, B5R, A5R, 8.5 ✕ 13, Postcard Auto inch: 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 13, 8.5 ✕ 11, 8.5 ✕ 11R, 7.25 ✕ 10.5R, 5.5 ✕ 8.5R Manual: 8K, 16K, 16KR Custom size: [Vertical] 100 to 297mm (3.9 to 11-5/8) [Horizontal] 139 to 432mm (5.5 to 17)

Paper size change method Guide adjustment by

Paper type setting YES

Allowable paper type and weight for paper feed Thin paper: 52 to 59g/m2 (14 to 15lbs) (single feed only) Plain paper: 60 to 105g/m2 (16 to 28lbs) Thick paper: 106 to 128g/m2 (29 to 34lbs) 176g/m2 (65 - lbs) Cover 205g/m2 (110lbs) Index (*)

Paper capacity (Standard paper) Plain paper: 100 sheets (standard paper: 80g/m2) Postcard: 20 sheets OHP: 20 sheets

Paper empty detection YES

Paper type Normal paper, recycled paper, printed paper, punched paper, color paper, letterhead, thin paper, label paper, thick paper, OHP, tab paper (tab width 20mm or less), Postcard

* 105g/m2 or above, A4/8.5 ✕ 11 or less. For 128g/m2 or above, horizontal feed only.

(4)

Duplex

System Paper size

Type and weight of paper which can be ed Paper type

(5) Non stack system A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR, 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 13.4, 8.5 ✕ 13, 8.5 ✕ 11, 8.5 ✕ 11R, 8.5 ✕ 5.5R, 7.25 ✕ 10.5R Plain paper: 60 to 105g/m2 (16 to 28lbs) Thick paper: 106 to 128g/m2 (29 to 34lbs) 176g/m2 (65 - lbs) Cover 205g/m2 (110lbs) Index Plain paper, printed paper, recycled paper, letterhead, punched paper, color paper, thick paper

Paper exit size / type

Paper exit position/ system Paper exit capacity Paper exit paper size/kind Remaining paper detection Paper exit paper full detection

Main unit top surface face-down paper exit 250 sheets (80g/m2 paper) All kinds of paper which can be fed None Provided

C. Scanner section (1)

Resolution/Gradation

copy mode Platen Magnification ratio Scan resolution (dpi) DSPF Magnification ratio Scan When in single copy resolution SPF duplex (front) CCD (dpi) SPF duplex (back) CIS When in the Fax send mode and the scanner FAX broadcast mode Select mode Standard Input and send Input resolution: OC 600 ✕ 600 resolution (dpi) Input resolution: DSPF simplex 600 ✕ 367 Input resolution: DSPF duplex (front) CCD 600 ✕ 600 Input resolution: DSPF duplex (back) CIS 600 ✕ 300 Transmission FAX 203.2 ✕ 97.8 resolution Internet FAX 200 ✕ 100 Scanner mode Select mode Input and send Input resolution: OC resolution (dpi) Input resolution: DSPF simplex Input resolution: DSPF duplex (front) CCD Input resolution: DSPF duplex (back) CIS Transmission resolution Exposure lamp None-electrode xenon lamp (Front), LED (Back) Scanning 256 gradations (8bit) Printing 2 gradations (1bit)

25 to 99 600 ✕ 600 25 to 99 600 ✕ 367

Normal ratio 600 ✕ 600 Normal ratio 600 ✕ 367

600 ✕ 600

600 ✕ 600

600 ✕ 300

600 ✕ 300

Fine text 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 203.2 ✕ 195.6 200 ✕ 200

Super fine test 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 203.2 ✕ 391 200 ✕ 400

200 ✕ 200 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 200 ✕ 200

300 ✕ 300 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 300 ✕ 300

* Except for FAX sending

MX-M700N SPECIFICATIONS 2 – 3

101 to 171 600 ✕ 600 101 to 117 600 ✕ 367 600x (600 ✕ 2) 600 ✕ 600 Ultra fine text 600 600 600 600 406.4 ✕ 391 400 ✕ 400 400 ✕ 400 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 400 ✕ 400

172 to 400 600 ✕ (600 ✕ 2) 118 to 200 600 ✕ 600 600x (600 ✕ 2) 600 ✕ 600 600dpi send (*) ✕ 600 ✕ 367 ✕ 600 ✕ 300 — 600 ✕ 600 600 ✕ 600 600 ✕ 600 600 ✕ 367 600 ✕ 600 600 ✕ 300 600 ✕ 600

(2)

Scanning area Original standard position Detection detection size

Manual detection size setting Dehumidificati on heater (Scanner section)

(3)

A. Copy functions

297 ✕ 431.8mm Left bottom reference

(1)

Provided Automatic detection (ed by changeover of the software destination of one kind of the detection unit.) Inch series-1 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 11, 8.5 ✕ 11R, 5.5 ✕ 8.5 Inch series-2 11 ✕ 17, 8.5 ✕ 13, 8.5 ✕ 11, 8.5 ✕ 11R, 5.5 ✕ 8.5 AB series-1 A3, B4, A4, A4R, B5, B5R, A5 AB series-2 A3, A4, A4R, B5, B5R, A5, 216 ✕ 330 AB series-3 B4, A4, A4R, A5, 8K, 16K, 16KR Manual setting fixed size input: Min. : 64 ✕ 64 to Max.297 ✕ 432mm Provided

Copy Fax Scanner Internet FAX Original standard position Document size

Document weight

Automatic detection Inch series-1: 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 11, 8.5 ✕ 11R, 8.5 ✕ 5.5, A4 Inch series-2 : 11 ✕ 17, 8.5 ✕ 13, 8.5 ✕ 11, 8.5 ✕ 11R, 8.5 ✕ 5.5, A4 AB series-1/-2: A3, B4, A4, A4R, B5, B5R, A5, 8.5 ✕ 11, 8.5 ✕ 13 AB series-3 : 8K, A4, A4R, B4, 16K, 16KR, A5, 8.5 ✕ 13 Mix paper feed (Same series, same width paper) enabled Manual setting Min. 64 ✕ 64 to Max.297 ✕ 432mm (Scan position: Center reference) 50 to 128g/m2 14 to 34lbs, 65 lbs Cover (Equivalent of 176g/m2), 110 lbs Index (Equivalent of 205g/m2) Max. 150 sheets (80g/m2) or Max. 19.5mm

55ppm 55 40

62ppm 62 45

70ppm 70 48

40

45

48

55 62 70 40 45 48 35 39 45 30 34 39 30 34 39 Since the next paper is fed after completion of paper exit outside the machine, it depends on the machine composition.

First copy time 55ppm

62ppm

4.0 seconds or less 6.2 seconds or less

70ppm 3.5 seconds or less 5.7 seconds or less

* Measurement conditions: Feeding A4/8.5 ✕11 paper from the main unit tray. Polygon in rotation.

(3)

Job speed

a. BLI standards

S to S S to D D to D

55ppm 50.1m (91%) 49.0m (89%) 51.7m (94%)

62ppm 56.4m (91%) 53.3m (86%) 57.0m (92%)

70ppm 63.0m (90%) 58.8m (84%) 63.0m (90%)

* S to S: A4/8 ✕ 11 documents 10 sheets, copy 5 sets * S to D: A4/8 ✕ 11 documents 10 sheets, copy 5 sets * D to D: A4/8 ✕ 11 documents 10 sheets (20 pages), copy 5 sets

(4)

Continuous copy

Multi max. quantity

(5)

Scan resolution Writing resolution

(6)

600 ✕ 600dpi 600 ✕ 600dpi

Copy document

Document size Document type

(7)

999 sheets

Resolution

Max. A3 Sheet/Book original

Copy magnification ratio

Copy magnification ratio

Zoom Preset magnification ratio

AB series:

25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200%, 400% Inch series: 25%, 50%, 64%, 77%, 100%, 121%, 129%, 200%, 400% 25 to 400% (25 to 200% for DSPF) 4

(8) Density, copy image quality processing

Type

System

Paper size A4, 8.5 ✕ 11 A4R, 8.5 ✕ 11R A5R/5.5 ✕ 8.5R, 5.5 ✕ 8.5-R B5 B5R, 7.25 ✕ 10.5-R B4/8.5 ✕ 14 A3/11 ✕ 17 Extra Postcard

Original Cover /DSPF Original Cover DSPF

DSPF: Duplex surface scan and feed unit When in single copy When in duplex copy 65 sheets/min 76 pages/min (600 ✕ 300 dpi, 1bit) (600 ✕ 300dpi, 1bit) 46 sheets/min 48 sheets/min (Normal text, 1bit) (Normal text, 1bit) 59 sheets/min 67 sheets/min (200 ✕ 200dpi, 1bit) (200 ✕ 200dpi, 1bit) 46 sheets/min 48 sheets/min (200 ✕ 100dpi, 1bit) (200 ✕ 100dpi, 1bit) Center reference

D. F section

Copy mode Original table mode

(2)

Service parts

Automatic document feeder

Max. loading capacity of documents

Copy speed (Continuous copy speed) (m)

a. Tray 1 to 4, LCC (Reduction/Normal/Enlargement)

Type Scan speed

(1)

2. Functional specifications

Document table

Heat roller pressure system

Exposure mode Number of manual steps Toner save mode

MX-M700N SPECIFICATIONS 2 – 4

Binary: Text (auto/manual), Text/Photo, photo, auto 9 steps Provided

(9)

B. Image send function

Paper size

Paper type AB series Inch series

Standard size Min. Max. A6 (A6R) A3 Postcard 8.5 ✕ 5.5

11 ✕ 17

(1)

Mode

Standard size A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR, Postcard 11 ✕ 17, 8.5 ✕ 14, 8.5 ✕ 13, 8.5 ✕ 11, 8.5 ✕ 11R, 7.25 ✕ 10.5R, 5.5 ✕ 8.5R

Scanner

(10) Copy functions Function (Special function)

Automatic paper selection Automatic magnification ratio selection Vertical/horizontal independent magnification ratio Paper type select Auto tray switching Rotation copy Electronic sort Rotation sort Job reservation Program call/ Document filing Preheat function

Auto power shut off function management (Dept. management) Process control Indefinite document size input Indefinite paper size input Mixed document feeder Binding margin Border erase/Center erase 2 in 1 Tandem copy Cover/Insert paper/Tab insert paper OHP insert paper Tab copy 2in1/4in1 Card shot Center binding Book copy Duplex copy system switch Large volume document mode

Black-white reversion Mirror image Date print Stamp Page print Character print

Yes Yes

Fax

Yes Yes Yes Yes Yes Yes (Europe, SCA, Dealer area) Yes (99 items) Yes (10 items) Yes Yes (Conditions set up by system setting) Yes (Conditions set up by system setting)

Internet Fax

Scan to E-mail Scan to Desktop (Scan data send without depending on the IP address under the DHPC environment) Scan to FTP Scan to Folder (SMB) Scan to e-mail with Meta Scan to Desktop with Meta Scan to FTP with Meta Scan to SMB with Meta Fax Fax to E-mail (inbound Routing) Fax to FTP/Desktop/SMB/E-mail (Document ) Internet Fax (ed full mode) Internet Fax to E-mail (inbound routing) Internet Fax to FTP/Desktop/SMB/E-mail (Document ) (*)

* Conforming to PC-FAX/PC-internet fax

(2)

Image send function (Push from the main unit)

a. system Item Corresponding server/protocol

Scanner SMTP FTP(T/IP) SMB

Internet Fax POP server SMTP server ESMTP server

SMTP, POP3 and FTP SSL. (Web ) b. image

Yes (500 s) Yes Yes Yes (Tray 3/manual paper feed) Yes (MIX only) Yes (Left/Right) Yes (Border/Center/Border+Center) Yes Yes (Network interface is required) Yes Yes Yes Yes (Centering provided) Yes (Centering provided) Yes (Centering provided) Yes Yes Yes (Max. 10000 sheets) Magnification ratio/ Density/ Paper can be changed for every bundle. Yes (except UK) Yes Yes Yes Yes Yes

Item File format Compression system

Scanner TIFF, PDF • Noncompression • G3 (1-dimensional) = MH (Modified Huffman) • G4 = MMR (Modified MR)

Internet Fax TIFF-FX (TIFF-F) MH, MMR

Fax — MH, MR, MMR, JBIG

c. Image process Item half tone reproduction Density adjustment Image quality selection Resolution (depends on file format/ transmission method)

MX-M700N SPECIFICATIONS 2 – 5

Scanner

Internet Fax

Fax

Equivalent of 256 steps Auto + 5 steps Half tone ON/OFF 200 ✕ 200dpi

Standard (200 ✕ 100dpi) (middle tone not allowed) Fine (200 ✕ 200dpi)

300 ✕ 300 dpi

Super fine (200 ✕ 400dpi)

400 ✕ 400 dpi

Ultra fine (400 ✕ 400dpi)

600 ✕ 600 dpi

600 ✕ 600dpi

Standard (203.2 ✕ 97.8dpi) (middle tone not allowed) Fine (203.2 ✕ 195.6dpi) Super fine (203.2 ✕ 391dpi) Ultra fine (406.4 ✕ 391dpi) —

d. Address specification Item Address specification

Setting of default address Number of Onetouch address key registration Inbound Routing List Inbound routing addresses Sender Number/ Address Registration (Inbound Routing) Number of Group (1 key) address registtation Program Direct address input Chain dial Resend Shortcut for address selection (quick key) CC/BCC sending Item name File name Return mail address

Sender name

• When broadcasting of the internet FAX and the scanner, the resolution is that of the internet FAX.

Scanner Internet Fax Fax Specified by one-touch, group, or direct address input. Input from the soft keyboard (Scanner/Internet FAX) Input the 10-key (Fax) Selection from LDAP server Resend Quick No Max. total 999 items (of which 200 items can be assigned to FTP, desktop and/or SMB) 50 items 1000 items

Item Memory transmission

Onhook Quick online send Direct transmission

Rotation send Zoom send Number of Group (1 key) address registration : Max. 500 items

Recall mode

Error Busy

8 items Input from the soft keyboard

Entry by 10key, # key, * key Yes (pause — key) Call up nearest address which are specified as a single destination Use the 10-key to call up ed numbers of addresses.

Yes

Yes (Selective from the list/direct entry from the list/ selection from LDAP server)

— — (1 default address fixed as sender name)

No

— —

Scanner Internet Fax Fax Specification by one-touch/group/direct address input. * Group, interface broadcasting total max: 5,000 items

Yes (Broadcast send is disabled for FTP/ Desktop/SMB)

Yes

—

Book document send Long document send File division send Send size limit Stamp function No. of registration items of senders Address Confirmation Function (Prevention of mis-send)

Scanner — When the upper limit value is set, memory send is performed. — — —

Internet Fax

Fax

Yes

Yes Yes Only in Onhook Yes (A3oB4, — A3oA4, B4oA4 Yes (Manual) Yes (Auto) Yes (Zooming of standard size to standard size only. (There are combinations that cannot be rotated.)) — Yes — — Yes The conditions of recall number and time can be set with the system setting. Yes Yes (Max.800mm) Yes — Yes — Yes Max. 999 items Yes (Soft switch)

—

g. Receive function

—

Selective/direct entry from the list Selective/direct entry from the list (1 default address fixed as — sender name)

e. Multiple address specification

Sequential send request

f. Send function

Automatic reduction send

500 items

Transmission message (message body) Mail footer preset

Item Address specification No. of registration items of direct address input * Broadcast send

• The compression type when broadcasting depends on the conforming of the system setting.

Item Automatic reception Manual reception Memory reception Fixed size reduction reception Specified size zoom reception Rotation reception Division reception Duplex reception 2 in 1 reception Domain/Address specification receive enable Domain/Address specification receive disable Certain rejection number setting External telephone connection remote Answering telephone connection Transfer function when output is disable Automatic boot mode

Yes

* Direct address input: 10-key other than one-touch, and soft keyboard input • When broadcasting including FAX, the resolution is that of FAX. MX-M700N SPECIFICATIONS 2 – 6

Internet Fax

Fax Yes Yes Yes Yes —

Yes Yes (Conditions are set by the system.) Yes (Conditions are set by the system.) — Yes (50 items)

—

Yes (50 items)

—

—

Yes (50 items)

— —

Yes No (PAT countermeasure) Yes Yes

C. Printer function

h. Report/list function Item Communication record table Communication result table Address/ Telephone number table Group table Sender table Program table Memory box table Memory contents clear notification table Receivable/ rejection number list Receivable/ Rejection address list Transfer-toemail table list Transfer-to list Web setting list

Scanner

Internet Fax

Fax

Yes NO

Platform

• IBM PC/AT compatible machine • Macintosh Yes

(2)

OS

Yes OS Yes Yes (Sender Yes (Described on the system registration table) setting list.) Yes Yes (FAX — mode only)

Windows

— (May be outputted in case of an error.) Mac —

Yes

Yes

—

98 Me NT 4.0 SP5 or later 2000 XP Server2003 Server2003 x64 XP x64 9.0 to 9.2.2 X 10.1.5 X 10.2.8 X 10.3.9 X 10.4 - X 10.4.7

Command system PCL5e, PCL6 compatible PS3 compatible

Yes

(4)

Yes

Scanner

Internet Fax

Fax

Yes —

Yes

—

Yes

—

NO

—

Yes

PPD

GPD

Yes Yes Yes Yes Yes Yes No No No No No No No

Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes

No No No No No No Yes Yes No No No No No

Yes (F code system) Yes (F code system)

—

—

— Corresponds by Net Scan Tool

NO Yes Yes Yes Yes PC-iFAX

PC-FAX

—

—

Internet Fax 293mm

Fax

A3 to A5/11 x 17 to 5.5 x 8.5

Fax Yes (Max. 20 digits) Yes (Max. 20 digits)

Standard Option (PS expansion kit)

Bitmap fonts PCL5 Latin font PCL Kanji font PS Latin font Bar code font

1 kind of font 80 PCL Latin fonts (SPDL) Standard built-in fonts Option (2 ACT Fonts) 136 Type 1 Latin fonts Auxiliary to the PS expansion kit Option

• The printing system is provided with one bitmap font compatible with HP and 80 European outline fonts for PCL. • In addition to this, when the PS expansion kit is installed, it is provided with 136 European outline fonts for PS and 5 Japanese outline fonts.

Yes NO

k. F code communication Item Sub address code

Custom PS

Built-in fonts

(5)

print channel

print channel

USB

j. Record size Item Max. record width Record size

Custom PCL5e/6 SPDL2 Yes Yes Yes Yes Yes Yes No No No No No No No

(3) Command system Yes

i. Other functions Item Time specification Poling receive Bulletin board send Cover function Sender print Page division Page connection Confidential data (Remote machine) Relay broadcast indication Send message Edge erase Center erase 2 in 1 Card shot Send to PC Linearrized PDF

(1)

For NetWare environment PSERVER/RPRINT LPR IPP PAP: EtherTalk (AppleTalk) FTP NetBEUI Port9100 WEB Submit Print

MX-M700N SPECIFICATIONS 2 – 7

NetWare environment PSERVER/RPRINT LPR IPP PAP : EtherTalk (AppleTalk) FTP FTP Pull Print NetBEUI Raw Port (Port 9100) USB 2.0 HTTP (WEB Submit Print) POP3 (E-mail To Print) USB 1.1: Windows98/98SE/Me/2000/XP only USB 2.0: Windows 2000/XP only Print channel in PSERVER/PRINT mode to be used in netware environment UNIX LPR/LPD command-compatible print channel Print channel in compliance with IPP1.0 Print channel used in the Macintosh environment Function to print receive data by use of the builtin FTP server. Microsoft NetBEUI compatible print channel s 9100 T port (Raw Port). This channel is used to set and print directly the files on the network by Web Page.

E-mail To Print

This channel is used to print only an attached file directly when an E-mail with an attached file is received.

• IPP, and HTTP s SSL.

(6) Command compatibility PCL5e compatible PCL6 compatible PostScript compatible

(7)

Environment setting

Setting item Default setting PCL setting PS setting

(8)

PCL5e is aimed to provide compatibility with HP LaserJet 4050. PCL6 is aimed to provide compatibility with HP LaserJet 4050. PostScript is aimed to provide compatibility with Adobe PostScript.

Outline Basic setting of printing such as the number of copies and printing direction. PCL symbol setting and font setting Setting of print enable/disable in a PS error

Print function

Functions Multiple Pamphlet Barcode font Network tandem print Windows Cluster Print PDF/TIFF direct print

E-Mail To Print PULL print from front USB PULL print SMB PULL print FTP PUSH print Print by setting the file on the Web Page. [Web Submit Print] ROPM Conforming to multi access Setting of the paper direction for duplex print of letterhead paper and punched paper Manual specification type/ Size detection enable setting Management of setting environment under the terminal server control Driver delivery function Form overlay Conforming to Planet Press Management of blind Web Page by the Bonjour for Macintosh environment

Document control print Missing-prevention marking Layout print No-line binding Chapter division

Content Two or more center bindings are collected into one. Compatible with JetCAPS BarDIMM emulation. True type font for barcode usable in PCL5e. Two main units are connected in network and printing can be made by the linkage of the two main unit. Even if one Windows server is down, the mirror server will execute the interrupted print job instead of the down server. PDF/TIFF files can be printed without the printer drivers. (1) Print of an attached file of an e-mail (2) Print from the FTP server (3) Print from the setting file on the Web page When an e-mail with an attached file is received, only the attached file is printed directly. The FTP server is checked from the front and only the specified file is pull-printed (direct print). The FTP server is checked from the front and only the specified file is pull-printed (direct print). The file folder on the network is checked from the front , and the specified file is pull-printed. Data are transferred from the client PC to the MFP server, and direct print is executed. A file on the network is set on the Web page, and direct print is executed.

PCL6/5e Yes Yes (5e only)

PS (OPTION) Yes No

Yes

Yes

Yes

Yes (Windows only)

Yes (PDF is No)

Yes

Yes

Yes

Yes

Yes

No

No

No Yes

No Yes

Yes

Yes

Yes Yes

Yes Yes

Yes

Yes

When the set value of the manual tray type on the main unit differs from that on the driver side, the set value of the printer driver has priority over the set value on the main unit and printing is made.

Yes

Yes

Under the meta-frame environment (under the auto print create environment), the print setting of each client is saved. (In order to avoid the trouble of having to set at every .)

Yes

Yes (Windows only)

Yes

Yes (Windows only)

Yes (5e only)

Yes

No

Yes (Windows only)

Yes

Yes

No

Yes

No

No

No

No

One RIP process allows to print two or more copies. RIP process can be executed during printing. Printing can be executed during scanning. For letterhead and punching sheet which has attribute of front and back, duplex print can be made in the proper front and back and proper page sequence.

The can distribute the driver to each client by PAU4. The form is ed to the main unit in advance, and only the data are sent to the main unit, where data are loaded into the form to be printed. s the Objectif Lune PlanetPress (which performs mapping between the ed form and the variable data in the printer). In order to block access to the address of a blind Web Page. The technology developed by Apple for detecting and connecting peripheral devices on the network automatically Without setting by the , the computer, the peripheral devices, and the software can be dynamically connected in network. (OS X 10.3 and later) The pattern is printed on paper. (When the data security kit is installed) The paper edge is marked in order to judge paper missing. The layout ed for various print purposes can be made. To prevent against bulge at the end when binding pages, center binding is executed for small lot of pages. A white sheet is automatically inserted so that the head page of each chapter comes on the odd (or even) page.

MX-M700N SPECIFICATIONS 2 – 8

No

No

No

No

No

No

(9)

Windows driver function

d. Image quality

a. Frequently used functions Functions Number of copies Print direction Duplex print

Center binding

Binding direction N-up

N-up direction

PCL5e 1 to 999

PCL6

PS

PPD (*)

Function Resolution Halftone

Vertical/Horizontal Simplex print, duplex print (Left/Upper/Right binding)

Invoice on Letter, Letter on Ledger, A5 on A4, A4 on A3, B5 on B4, Letter on Letter, Ledger on Ledger, A4 on A4, A3 on A3, B4 on B4 Left/Upper/Right 2/4/6/8/9/16

Simplex print, duplex print (Long side/Short side binding) Windows2000, XP: Yes Other OS: No Long side/Short side WindowsNT 4.0: — Windows2000, XP: 2/4/6/9/16 Other OS: 2/4

[2-Up]: Left to Right / Right to Left [4, 6, 8, 9, 16-Up]: Right, and Down / Down, and Right Left, and Down / Down, and Left

N-up frame line

Graphic mode selection Smoothing Toner save Ultra fine photo

PCL5e PCL6 600/300dpi (55ppm/ 62ppm) — Yes/No (70ppm) — Raster Raster HP-GL2 vector 55/62ppm: Yes 70ppm : No

definition type Paper feed system Cover paper/ Back cover page Cover paper Insert paper OHP insert paper

Black-white reversion Mirror image

—

Yes/No Horizontal /Vertical

—

Zoom Fit page

— Yes/No

Offset

25 to 400% —

e. Font Function Usable built-in fonts

PCL5e PCL6 80 fonts Category 3 and 4 In font chapter

system which can be selected

Bitmap, TrueType, Graphics

Yes (Always prints border line)

Yes/No

PCL5e PCL6 PS PPD (*) A3/B4/A4/B5/A5/Postcard/Ledger/Legal/Foolscap/Letter/ Executive/Invoice/8K/16K Normal paper, letterhead, printed paper, punched paper, recycled paper, color paper, label sheet, thick paper, OHP, tab paper 7 types

PS 136 fonts Category 1In font chapter 5 Japanese fonts Category 2 In font chapter

PPD (*) (For Windows NT4.0) Traditional 35 Latin fonts Category 1 In font chapter (For Other OS) 136 Latin fonts Category 1 In font chapter 5 Japanese fonts Category 2 In font chapter Bitmap, Type 1, TrueType

f. Other functions Auto paper feed, Tray 1/2/3/4/5, manual feed Yes/No Setting of Duplex/Simplex/ No print

—

Function Units composition setting Watermark

PCL5e

PCL6

PS

Yes Yes Yes Yes

Yes (Limitations on functions) — — — —

Yes

—

Yes Yes

— —

Yes

—

Yes Yes No/Yes (White paper) Yes (Printed paper)

— —

PCL5e PCL6 PS PPD (*) • Center tray • Finisher o Tray 1 • Finisher oTray 2 • Saddle stitch finisher oTray 1 • Saddle stitch finisher oTray 2 • Saddle stitch finisher o Saddle stitch tray Finisher • No staple • 1 position • 2 positions Saddle stitch finisher • No staple • 1 position • 2 positions Yes (every time)

Overlay Print hold Job retention Sample print Print department management setting Option auto setting Job complete notification Tandem print Carbon print Enlargement continuous copy Vertical/horizontal independent magnification ratio Cover insertion +center binding Document filing

PPD (*)

Yes Yes

c. Paper exit method

Staple

Horizontal

* For printing, the PS driver bundled in Windows is required.

* For printing, the PS driver bundled in Windows is required.

Functions Paper exit destination setting

—

Yes/No

b. Paper feed system

Paper type

PPD (*) 600dpi Screen Frequency 8.0 to 360.0 in 0.1 steps Screen angle 0.0 to 360.0 in 0.1 steps

55/62ppm: Yes 70ppm : No

* For printing, the PS driver bundled in Windows is required.

Functions Paper size

PS

Yes Yes

— —

—

Yes

—

Yes

—

Yes

—

* For printing, the PS driver bundled in Windows is required.

* For printing, the PS driver bundled in Windows is required.

MX-M700N SPECIFICATIONS 2 – 9

(10) Windows PPD, Macintosh PPD driver funciton a. Frequently used functions Functions Number of copies Print direction Duplex print Center binding Binding direction N-up N-up direction N-up frame line

Macintosh PPD 1 to 999 Vertical/Horizontal Simplex print, duplex print (Left/Upper binding) Yes Long side/Short side 2/4/6/8/16 Z / Reverse Z/N / Reverse N None / Single Hairline / Single Thinline / Double Hairline / Double Thinline

b. Paper feed system Functions Paper size Paper type

definition type Paper feed system Cover paper/Back cover page Cover paper Insert paper OHP insert paper

Macintosh PPD A3, B4, A4, B5, A5, Postcard, Ledger, Legal, Foolscap, Letter, Executive, Invoice, 8K, 16K Normal paper, letterhead, printed paper, punched paper, recycled paper, color paper, label sheet, thick paper, OHP, tab paper 7 types Auto paper feed, Tray 1/2/3/4/5, manual feed Yes/No Yes NO No/Yes (White paper), Yes (Printed paper)

c. Paper exit method Function Paper exit destination setting

Staple

Offset

Macintosh Top tray Finisher Tray1 Tray2 Saddle stitch finisher Tray1 Tray2 Saddle stitch tray Finisher • No staple • 1 position • 2 positions Saddle stitch finisher • No staple • 1 position • 2 positions • Saddle stitch Yes (every time)

d. Image quality Function Resolution Halftone Graphic mode selection Smoothing Toner save Ultra fine photo Black-white reversion Mirror image Zoom Fit page

Macintosh 600dpi (55ppm/62ppm) Yes/No (70ppm) —

Macintosh Yes (Mac OS9.x.x - LaserWriter)

f. Other functions Function Units composition setting Watermark Overlay Print hold Job retention Sample print Print department management setting Option auto setting Job complete notification Tandem print Carbon print Enlargement continuous copy Vertical/horizontal independent magnification ratio Cover insertion +center binding Document filing

Macintosh Yes Yes No Yes Yes (PIN code input enable) Yes Yes — Yes — Yes Yes — — — —

(11) Print performance

Model 55ppm

62ppm

70ppm

PDL type PCL6 PCL5e PS ppd PCL6 PCL5e PS ppd PCL6 PCL5e PS ppd

Word: script.doc (eng.) A total of 9 pages 16.2 sec 15.4 sec 15.8 sec 14.1 sec 13.8 sec 15.4 sec 15.6 sec 13.4 sec 14.6 sec 15.4 sec 14.6 sec 14.3 sec

* Measurement conditions (Windows) PC: Pentium III 1GHz 128MB OS: Windows XP Professional Driver setting: Default Software: Microsoft Office XP

Excel: xl8garly.xls A total of 20 pages 33.7 sec 32.4 sec 50.0 sec 37.1 sec 31.4 sec 31.5 sec 49.9 sec 41.3 sec 31.1 sec 30.5 sec 49.2 sec 37.0 sec

PowerPoint: Pw4051.ppt A total of 6 pages 10.5 sec 13.0 sec 13.9 sec 11.6 sec 12.8 sec 12.7 sec 13.9 sec 12.2 sec 11.9 sec 13.3 sec 13.4 sec 11.0 sec

(Macintosh) PC: PowerPC G3 700MHz 256MB

— (55ppm/62ppm) : Yes/No (70ppm) : — Yes/No —

D. Document filing function (1)

Basic function

Yes/No

Document filing capacity Fixed folder

Horizontal/Vertical 25 to 400% No

Number of pages for one file

e. Font Function Usable built-in fonts

Function system which can be selected

Macintosh Traditional 35 PS Latin fonts Category 1 In font chapter 5 fonts Category 2 In font chapter

Number of folders which can be formed in the folder Number of s which can be ed

MX-M700N SPECIFICATIONS 2 – 10

16GB Standard folder/ folder

Max. 20000 pages or 3000 files Max. 10000 pages Temporary folder or 1000 files Conforms to the large volume document mode. (Within the HD capacity) Max. 500 folders Max. 500 s

2

(2)

: '07 Nov 15

3.

Data operation by each function

Job

Copy Printer Direct print (FTP pull) Direct print (FTP push) Direct print (e-mail) Direct print (Web) Scan send Scan to HDD FAX receive FAX send Internet FAX receive Internet FAX send PC-Fax/PC-INternet Fax transmisson Data input

Each folder in the standard folder/ folder Storage Storage of of sharing Confidential Yes Yes Yes Yes No No No No Yes No No No Yes No Yes Yes No No Yes No No No Yes No

Environmental conditions

A. Environmental conditions for use of the main Temporary folder Storage of sharing Yes Yes Yes Yes Yes Yes Yes No No Yes No Yes

Storage of Confidential No No No No No No No No No No No No

Yes

Yes

Yes

No

Yes

Yes

Yes

No

Temperature: 10°C to 35°C Humidity: 20 to 85% RH Air pressure: 590 to 1013hPa (height: 0 to 2000m) (Humidity) 85% 60%

20%

10͠

30͠ 35͠ (Temperature)

B. Environmental conditions for transit of the main unit –20°C to 45°C (No condensation)

E. Safety and environmental standards (1) 2 Item

North America

Safety standards

UL60950-1, CSA C22.2 No.60950-1 -03, 21CFR (Laser) FCC Part 15 Class B, ICES-003 Class B

Environmental standards (EMC)

Line standards (When the FAX expansion board is installed.)

(2)

Humidity (RH)

Safety standards

FCC Part 68, ICCS-03

85% Standard Europe (Western/ Australia North) EN60950-1, IEC60950-1, IEC60950-1, IEC60825-1 IEC60825-1 (Laser) (Laser)

EN55022 Class B, CISPR22 Class B, EN61000-3-2, EN61000-3-3, EN55024 TS103021 or TBR21, EG201120, EG201121

60% China / Taiwan

20%

AS/NZS CISPR22 Class B (EN 55022 Class B)

GB9254 Class B, GB17625.1, GB/T17618, CNS13438 Class B

AS/ACIF S0002, AS/NZS 60950

GB/T3382.1, GB/T3382.2, YD/T514, YD/T589, YD/T703, YD/T965, YD/T993, PSTN01

C. Operating environmental conditions (Supply) Humidity (RH) 85% 60%

20%

Environmental standards Standard International Energy Star Program MFP (EPA) Environmental Choice Program (E) Nordic swan WEEE (The machine shipped for Europe only) European ROHS regulations

2

D. Ambient conditions for transporting –20qC to 45qC (No condensation)

E. Environmental conditions for storing unopened consumable parts –10qC to 40qC (No condensation)

F. Standard storage period of unopened consumable parts Taiwan battery

1)

Photoconductor drum

2)

Toner/Developer

36 months from the production month

(3)

Noise

24 months from the production month Operating Standby (Standby mode)

7.3B or less 5.5B or less

MX-M700N SPECIFICATIONS 2 – 11

2

MX-M700N [3] CONSUMABLE PARTS

5GTXKEG/WCN

1. Supply system table A. U.S.A, Canada, South and Central America No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

x 10 x 10

x1

Life 830k (83k x 10)

Model name AR-621MTA

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620MD

1

AR-620DR

10

Remark * Life setting by A4 6% document Two bags needed.

B. Europe s (Including East Europe, Russia)/Australia/New Zealand/UK No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

Life 830k (83k x 10)

Model name AR-621LT

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620LD

1

AR-620DM

10

Life 830k (83k x 10)

Model name AR-621CT

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620CD

1

AR-620DR

10

Life 830k (83k x 10)

Model name AR-621CT-C

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620CD-C

1

AR-620DR-C

10

x1

Life 83k (83k x 1)

Model name AR-622ST-C

Packing 10

x1

62/70ppm: 150k

AR-620SD-C

10

x1

62/70ppm: 300k

AR-620DR-C

1

x 10 x 10

x1

Remark * Life setting by A4 6% document Two bags needed.

C. Asia s No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

x 10 x 10

x1

Remark * Life setting by A4 6% document Two bags needed.

D. Hong Kong No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

x 10 x 10

x1

Remark * Life setting by A4 6% document Two bags needed.

E. China No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip Developer (Black) (Developer; Net weight 725g) OPC drum

MX-M700N CONSUMABLE PARTS 3 – 1

Remark * Life setting by A4 6% document Two bags needed.

F. Middle East/Philippine No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

x 10 x 10

x1

Life 830k (83k x 10)

Model name AR-621ET

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620CD

1

AR-620DR

10

Life 830k (83k x 10)

Model name AR-621ET

Packing 1

62/70ppm: 1500k (150k x 2bags x 5) 55ppm: 1250k (125k x 2bags x 5) 62/70ppm: 300k 55ppm: 250k

AR-620LD

1

AR-620DM

10

Remark * Life setting by A4 6% document Two bags needed.

G. Taiwan No. 1

Part name Toner cartridge (Black)

2

Developer (Black)

3

Drum

Content Toner cartridge (Black) (Toner; Net weight 1815g) With IC chip Developer (Black) (Developer; Net weight 725g)

OPC drum

x 10 x 10

x1

Remark * Life setting by A4 6% document Two bags needed.

2. Maintenance parts list A. U.S.A, Canada No. 1

Part name Maintenance kit 1

Content Side seal F Side seal R MC cleaning unit Cleaner blade Drum separation pawl Screen grid Toner reception seal Charging plate Paper dust removal unit DV seal DV side seal F DV side seal R Toner filter Transfer cleaning roller Transfer belt Transfer roller Transfer gear Upper heat roller Fusing separation pawl (Upper) Lower heat roller Fusing separation pawl (Lower) Cleaner blade

x1 x1 x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x6 x1 x4 x 10

2

Maintenance kit 2

3

Upper heat roller kit

4

Lower heat roller kit

5

Cleaner blade

6

Cleaning kit

Staple cartridge

Lower CL roller DG2 CL roller SP CL roller bearing Auxiliary CL roller SP CL auxiliary roller DG Heat CL sheet base N AS Web roller DG2 Pressure roller DG2 Web bearing Pressure bearing Pressure SP Fusing UN (Heater lamp 120V) Heat roller Heat roller bearing DSPF paper feed roller DSPF pickup roller DSPF separation roller Main unit paper feed roller Main unit paper feed pickup roller Main unit paper feed separation roller Finisher staple

x 10 x 20 x 40 x 20 x 10 x 10 x 10 x 10 x 20 x 20 x 20 x1 x1 x2 x1 x1 x1 x1 x1 x1 x3

7 8

Fusing unit Heat roller kit

9

DSPF roller kit

10

Paper feed roller kit

11

12

Staple cartridge

Saddle finisher staple

x3

Life 300K

Model name AR-620KA

Packing 10

300K

AR-620KB

10

300K

AR-620UH

10

300K

AR-620LH

10

300K (x 10)

AR-620CB

1

300K (x 10)

MX-705CR

1

— 300K

MX-705FU1 AR-620HR

1 10

100K

AR-620DF

10

100K

AR-620RT

10

5,000 times x 3

SF-SC11

20

2,000 times x 3

AR-SC3

40

MX-M700N CONSUMABLE PARTS 3 – 2

Remark

AR-620CB = (AR-620BL) x 10 MX-705CR = (MX-705RC) x 10

Cartridge for AR-F15 (Common with the cartridge for AR-F11/F12) Cartridge for AR-F16 (Common with the cartridge for AR-F12)

B. Europe s (Including East Europe, Russia) Australia/New Zealand/UK No. 1

Part name Maintenance kit 1

Staple cartridge

Content Side seal F Side seal R MC cleaning unit Cleaner blade Drum separation pawl Screen grid Toner reception seal Charging plate Paper dust removal unit DV seal DV side seal F DV side seal R Toner filter Transfer cleaning roller Transfer belt Transfer roller Transfer gear Upper heat roller Crimping roller EX Upper separation pawl N Lower separation pawl Heat roller Heat roller bearing Lower CL roller DG2 CL roller SP CL roller bearing Auxiliary CL roller SP CL auxiliary roller DG Heat CL sheet base N AS Web roller DG2 Pressure roller DG2 Web bearing Pressure bearing Pressure SP Fusing UN (Heater lamp 230V) DSPF paper feed roller DSPF pickup roller DSPF separation roller Main unit paper feed roller Main unit paper feed pickup roller Main unit paper feed separation roller Finisher staple

x1 x1 x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x6 x4 x1 x2 x1 x2 x4 x2 x1 x1 x1 x1 x2 x2 x2 x1 x1 x1 x1 x1 x1 x1 x3

2

Maintenance kit 2

3

Maintenance kit 3

4 5

Fusing unit DSPF roller kit

6

Paper feed roller kit

7

8

Staple cartridge

Saddle finisher staple

x3

Life 300K

Model name AR-620KA

Packing 10

300K

AR-620KB

10

300K

MX-705KC

5

— 100K

MX-705FU AR-620DF

1 10

100K

AR-620RT

10

5,000 times x 3

SF-SC11

20

2,000 times x 3

AR-SC3

40

MX-M700N CONSUMABLE PARTS 3 – 3

Remark

Cartridge for AR-F15 (Common with the cartridge for AR-F11/F12) Cartridge for AR-F16 (Common with the cartridge for AR-F12)

C. Middle East/Asia/South and Central America No. 1

Part name Maintenance kit 1

Staple cartridge

Content Side seal F Side seal R MC cleaning unit Cleaner blade Drum separation pawl Screen grid Toner reception seal Charging plate Paper dust removal unit DV seal DV side seal F DV side seal R Toner filter Transfer cleaning roller Transfer belt Transfer roller Transfer gear Upper heat roller Crimping roller EX Upper separation pawl N Lower separation pawl Heat roller Heat roller bearing Lower CL roller DG2 CL roller SP CL roller bearing Auxiliary CL roller SP CL auxiliary roller DG Heat CL sheet base N AS Web roller DG2 Pressure roller DG2 Web bearing Pressure bearing Pressure SP Fusing UN (Heater lamp 230V) DSPF paper feed roller DSPF pickup roller DSPF separation roller Main unit paper feed roller Main unit paper feed pickup roller Main unit paper feed separation roller Finisher staple

x1 x1 x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x6 x4 x1 x2 x1 x2 x4 x2 x1 x1 x1 x1 x2 x2 x2 x1 x1 x1 x1 x1 x1 x1 x3

2

Maintenance kit 2

3

Maintenance kit 3

4 5

Fusing unit DSPF roller kit

6

Paper feed roller kit

7

8

Staple cartridge

Saddle finisher staple

x3

Life 300K

Model name AR-620KA

Packing 10

300K

AR-620KB

10

300K

MX-705KC

5

— 100K

MX-705FU AR-620DF

1 10

100K

AR-620RT

10

5,000 times x 3

SF-SC11

20

2,000 times x 3

AR-SC3

40

MX-M700N CONSUMABLE PARTS 3 – 4

Remark

Cartridge for AR-F15 (Common with the cartridge for AR-F11/F12) Cartridge for AR-F16 (Common with the cartridge for AR-F12)

D. Hong Kong No. 1

Part name Maintenance kit 1

Staple cartridge

Content Side seal F Side seal R MC cleaning unit Cleaner blade Drum separation pawl Screen grid Toner reception seal Charging plate Paper dust removal unit DV seal DV side seal F DV side seal R Toner filter Transfer cleaning roller Transfer belt Transfer roller Transfer gear Upper heat roller Crimping roller EX Upper separation pawl N Lower separation pawl Heat roller Heat roller bearing Lower CL roller DG2 CL roller SP CL roller bearing Auxiliary CL roller SP CL auxiliary roller DG Heat CL sheet base N AS Web roller DG2 Pressure roller DG2 Web bearing Pressure bearing Pressure SP Fusing UN (Heater lamp 230V) DSPF paper feed roller DSPF pickup roller DSPF separation roller Main unit paper feed roller Main unit paper feed pickup roller Main unit paper feed separation roller Finisher staple

x1 x1 x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x6 x4 x1 x2 x1 x2 x4 x2 x1 x1 x1 x1 x2 x2 x2 x1 x1 x1 x1 x1 x1 x1 x3

2

Maintenance kit 2

3

Maintenance kit 3

4 5

Fusing unit DSPF roller kit

6

Paper feed roller kit

7

8

Staple cartridge

Saddle finisher staple

x3

Life 300K

Model name AR-620KA

Packing 10

300K

AR-620KB

10

300K

MX-705KC

5

— 100K

MX-705FU AR-620DF

1 10

100K

AR-620RT

10

5,000 times x 3

SF-SC11

20

2,000 times x 3

AR-SC3

40

MX-M700N CONSUMABLE PARTS 3 – 5

Remark

Cartridge for AR-F15 (Common with the cartridge for AR-F11/F12) Cartridge for AR-F16 (Common with the cartridge for AR-F12)

E. Taiwan No. 1

Part name Maintenance kit 1

Staple cartridge

Content Side seal F Side seal R MC cleaning unit Cleaner blade Drum separation pawl Screen grid Toner reception seal Charging plate Paper dust removal unit DV seal DV side seal F DV side seal R Toner filter Transfer cleaning roller Transfer belt Transfer roller Transfer gear Upper heat roller Crimping roller EX Upper separation pawl N Lower separation pawl Heat roller Heat roller bearing Lower CL roller DG2 CL roller SP CL roller bearing Auxiliary CL roller SP CL auxiliary roller DG Heat CL sheet base N AS Web roller DG2 Pressure roller DG2 Web bearing Pressure bearing Pressure SP Fusing UN (Heater lamp 100V) DSPF paper feed roller DSPF pickup roller DSPF separation roller Main unit paper feed roller Main unit paper feed pickup roller Main unit paper feed separation roller Finisher staple

x1 x1 x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x6 x4 x1 x2 x1 x2 x4 x2 x1 x1 x1 x1 x2 x2 x2 x1 x1 x1 x1 x1 x1 x1 x3

2

Maintenance kit 2

3

Maintenance kit 3

4 5

Fusing unit DSPF roller kit

6

Paper feed roller kit

7

8

Staple cartridge

Saddle finisher staple

x3

Life 300K

Model name AR-620KA

Packing 10

300K

AR-620KB

10

300K

MX-705KC

5

— 100K

MX-705FU2 AR-620DF

1 10

100K

AR-620RT

10

5,000 times x 3

SF-SC11

20

2,000 times x 3

AR-SC3

40

MX-M700N CONSUMABLE PARTS 3 – 6

Remark

Cartridge for AR-F15 (Common with the cartridge for AR-F11/F12) Cartridge for AR-F16 (Common with the cartridge for AR-F12)

MX-M700N

5GTXKEG/WCN [5] EXTERNAL VIEW AND INTERNAL STRUCTURE 1. Identification of each section and functions A. External view

1

2

3

4

5

6

7

8

9

10

14

13 12

11

Finisher No.

Parts

1

Name Saddle stitch finisher *1 / Finisher*1

2 3

Punch module*1 Inserter*1

4 5 6 7 8

Automatic document feeder Front cover Operation Center tray By tray

9

Power switch

10

12

Paper feed tray 5 (Large capasity tray)*1 Paper feed tray 5 (Large capasity tray)*1 Paper feed trays 1, 2

13

Paper feed tray 3

14

Paper feed tray 4

11

Funciton/Operation The finisher and the saddle stitch finisher include the offset function, which offsets each set of copies from the preceding set for easy separation. Each set of sorted copies can also be stapled. The saddle stitch finisher can automatically staple at the center line of a set of copies and fold the pages to create a pamphlet. A punch unit can be installed to add punch holes to copioes, and an inserter can be installed to insert blank pages at specified pages. Adds punch holes to printed pages. The inserter enables blank sheets or printed sheets to be added to copy and print output as covers or inserts without printing. Printed output can also be fed one set at a time from the inserter for stapling or punching without performing stapling or staple sorting finishing. This automatically feeds and scans multiple sheet originals. Both sides of two-sided originals can be scanned at once. Open to replace toner cartridge. Performs various setting, display, and simulation operations. Finished sheets are deposited here Special papers (including transparency film) and copy paper can be fed from the by tray. Turns the power on and off. If the power does not come on when the power switch is turned on, check the main power switch to see if it is turned on. The large capacity tray can hold up to 3,500 sheets of commonly used (8-1/2” ✕ 11”, B5, A4) any standard paper (20 lbs. (80 g/m2)). The large capacity tray can hold up to 3000 sheets of 20 lbs. (80 g/m2) paper.

NOTE

The trays hold paper. Approximately 800 sheets of standard 8-1/2” ✕ 11” or A4 size paper (20 lbs. (80 g/m2)) can be loaded in tray 1, and approximately 1200 sheets of standard 8-1/2” ✕ 11”, A4 or B5 size paper (20 lbs. (80 g/m2)) can be loaded in tray 2. Tray 3 holds. Approximately 500 sheets of standard (20 lbs. (80 g/m2)) paper can be loaded in this tray. Tabbed paper and transparencies can also be loaded. Tray 4 holds. Approximately 500 sheets of standard (20 lbs. (80 g/m2)) paper can be loaded in this tray.

*1: 1, 2, 3, 10 and 11 are peripheral devices. For information on these devices, see the explanations of the devices in the manual. MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 1

B. Internal operation parts

1

2

3

4 5

6

7

10

9 No. 1 2 3 4 5 6 7 8 9 10

8 Parts

Name Duplex unit Fusing unit

Funciton/Operation Open the cover to remove a misfeed from the fusing/duplex unit. Toner images are fused here.

Cover of the duplex unit Toner cartridge Main power switch Right side cover Upper cover of large capacity tray Left side cover release Left cover of paper drawer OPC drum

Open when a misfeed has occurred in the duplex unit. The toner cartridge must be replaced by the indication on the operation . Keep this switch turned on when the fax option or network scanner option is installed. Open when a misfeed has occurred in by tray or large capacity tray. Open when a misfeed has occurred in large capacity tray.

NOTE

The fusing unit is hot. Take care in removing misfed paper.

Push this knob up to open the left side cover. Open this cover to remove paper misfed in the tray 3 and tray 4. Images are formed on the photoconductive drum.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 2

Do not touch or damage the photoconductive drum.

C. Operation, display parts

1

2

3

PRINT READY DATA

DOCUMENT FILING

LINE DATA

IMAGE SEND COPY

SYSTEM JOB STATUS SETTINGS

4 No. 1

5



6

7

8

9

Parts Name Touch

2

Mode select keys and indicators

3

PRINT mode indicators

4 5

[JOB STATUS] key [SYSTEM SETTINGS] key

6 7

Numeric keys [*] key ([] key)

8

[#/P] key

9

[C] key (Clear key)

10

[START] key

11

[CA] key (Clear all key)

Funciton/Operation The machine status, messages and touch keys are displayed on the . The document filing, copy, network scanner*1, and fax*2, Internet fax*3 functions are used by switching to the screen for the desired function. See the following page. Use to change modes and the corresponding display on the touch . [DOCUMENT FILING] key Press to select the document filing mode. [IMAGE SEND] key/LINE indicator/DATA indicator Press to change the display to network scanner mode*1, fax mode*2 or Internet fax mode*3. [COPY] key Press to select the copy mode. • READY indicator Print data can be received when this indicator is lit. • DATA indicator Lights up or blinks when print data is being received. Also lights up or blinks when printing is being performed. Press to display the current job status. This is used to store, edit, and delete names and folder names for the document filing function, and to configure the settings and printer configuration settings. Use to enter number values for various settings. This key is used in copy mode, document filing mode, network scanner mode*1, fax mode*2, and Internet fax mode*3. This is used as a program key when using the copy function, and to dial when using the fax function*2. This key is used in copy mode, document filing mode, network scanner mode*1, fax mode*2, and Internet fax mode*3. Use this key to start copying in copy mode, scan a document in network scanner mode*1, or scan a document for transmission in fax mode*2 or Internet fax mode*3. This key is used in copy mode, document filing mode, network scanner mode*1, fax mode*2, and Internet fax mode*3. Use the key to cancel settings and perform an operation from the initial machine state.

*1: When the network scanner option is installed. *2: When the fax option is installed. *3: When the Internet fax option is installed.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 3

10

11 NOTE

D. Job status screen (common to print, copy, fax, network scan and internet fax) This screen is displayed when the [JOB STATUS] key on the operation is pressed. This screen can be used to display the “JOB QUEUE” (showing stored jobs and the current job) or the “COMPLETE” job list (showing finished jobs). This screen is used to check jobs, move a job to the top of the JOB QUEUE, or delete a job.

1

"JOB QUEUE" screen JOB QUEUE

SETS / PROGRESS

1/1

020 / 001

COPYING

COPY

020 / 000

PAPER EMPTY

Suzuki

020 / 000

WAITING

066211221

002 / 000

WAITING

3 No. 1

STATUS

COPY

PRINT JOB

Name Job list

2

*1

4

JOB QUEUE

JOB QUEUE

COMPLETE

COMPLETE

DETAIL

DETAIL

PRIORITY STOP/DELETE

5

CALL

INTERNET-FAX

INTERNET-FAX

FAX JOB

SCAN

6

7

8 9 10

(Displayed in the touch ) Function/Operation The displayed jobs in the job list are themselves operation keys. To cancel printing or to give a job the highest print priority, touch the relevant job key to select the job and execute the desired operation using the keys described in 8 and 9. This shows the current job and the jobs waiting to be run. The icons to the left of the jobs in the queue show the job mode. The document filing reprint job icon is highlighted. Note that the icon does not become highlighted during retransmission of a fax/image transmission job.

Print mode

Copy mode SCAN mode

Scan to e-mail job

Scan to FTP job

Scan to Desktop job Scan to Network folder job

Fax mode Fax send job

Fax reception job

PC-FAX send job Internet Fax mode i-Fax send job

i-Fax reception job

PC-Internet Fax send job

2

Mode select key

3

[PRINT JOB] key

4

[SCAN] key

5

[FAX JOB] key

"COMPLETE" job screen

This switches the job list display between “JOB QUEUE” and “COMPLETE”. “JOB QUEUE”: Shows stored jobs and the job in progress. “COMPLETE”: Shows finished jobs. Files saved using the “FILE” and “QUICK FILE” functions and finished broadcast transmission jobs appear as keys in the finished job screen. The “FILE” or “QUICK FILE” job keys in the finished job screen can be touched, followed by the [CALL] key, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the transmission. This displays the print job list of print mode (copying, printing, fax reception, Internet fax reception, and self printing). This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, and Scan to Desktop) when the network scanner option is installed. This displays the transmission/reception status and finished jobs of fax mode (fax and PC-Fax) when the fax option is installed.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 4

11 NOTE

*1: “PAPER EMPTY” in the job status display When a job status display indicates “PAPER EMPTY”, the specified paper size for the job is not loaded in any of the trays. In this case, the job will be suspended until the required paper is loaded. Other stored jobs will be printed (if possible) until the required paper is loaded. (Other jobs will not be printed if the paper runs out during printing.) If you need to change the paper size because the specified paper size is not available, touch the current job key to select it and then touch the [DETAIL] key described in 10.

No. 6 7

Name Display switching keys [INTERNET-FAX] key

8

[STOP/DELETE] key

9

[PRIORITY] key

10

[DETAIL] key

11

[CALL] key

(Displayed in the touch ) Function/Operation Use to switch the page of the displayed job list. This displays the transmission/reception status and finished jobs of Internet fax mode and PC Internet fax mode when the network scanner option is installed. Use to cancel or delete the current job or delete the selected reserved job. Note that printing of received faxes and received Internet faxes cannot be canceled or deleted. A stored job in the “JOB QUEUE” job list can be printed ahead of all other stored jobs by selecting the job and then touching this key. This shows detailed information on the selected job. Files saved using the “FILE” and “QUICK FILE” functions and finished broadcast transmission jobs appear as keys in the finished job screen. A Quick File in the finished job screen or the [Filing] key can be touched, followed by the [CALL] key, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the transmission. When this key is touched after selecting a job in the COMPLETE job status screen (a job stored using the FILE or QUICK FILE keys of the document filing function), the “JOB SETTINGS” menu screen appears to let you resend or reprint the finished job.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 5

NOTE

E. Sensor/detector SPED1 STUD

SPLS2

SPPD1

SPLS1 SPWS STLD

SPPD3 SPPD4

SPED2

SPOD

POD3

POD2

AINPD

SPPD2

POD1

APPD1

MPED MPLD1

MPFD1 MPFPWS

PPD APPD2

MPLD2

MPRD1

MPRD2

MTOP1 MTOP2

MPFD2 LPPD

PFD2 T2LUD T1LUD

T1PPD

T2PED

T1PED

Code

Signal name

AINPD

AINPD

APPD1

APPD1

APPD2

APPD2

LPPD

LPPD

M1LUD

M1LUD

M1PFD

M1LUD M1PED

M2PFD

M2LUD M2PED

Name

Function/Operation

Type

Duplex (ADU) paper entry detector Duplex (ADU) paper detector 1 Duplex (ADU) paper detector 2 LCC paper detector

Duplex (ADU) paper entry detection, detection of paper exit to finisher Duplex (ADU) upstream paper detection Duplex (ADU) midstream paper detection Detection of paper entry from LCC

Paper tray upper limit detector (Paper feed tray 3)

Paper tray upper limit detection (Paper feed tray 3)

Transmission type Transmission type Transmission type Transmission type Transmission type

Connector level “L” “H” Paper – Paper – Paper – Paper – – Upper limit detection

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 6

NOTE Paper transport system sensor Paper transport system sensor Paper transport system sensor Paper transport system sensor Paper feed tray system sensor

Code

Signal name

Name

Function/Operation

M1PED

M1PED

M1PFD

M1PFD

M2LUD

M2LUD

M2PED

M2PED

M2PFD

M2PFD

MPED

MPED

MPFD1

MPFD1

MPFD2

MPFD2

MPFPWS

MPFPWS

MPLD1

MPLD1

MPLD2

MPLD2

MPRD1

MPRD1

MPRD2

MPRD2

MTOP1

MTOP1

MTOP2

MTOP2

PFD2

PFD2

Paper empty detector (Paper feed tray 3) Paper detector (Paper feed tray 3) Paper tray upper limit detector (Paper feed tray 4) Paper tray upper limit detector (Paper feed tray 4) Paper detector (Paper feed tray 4) Manual feed paper empty detector Manual feed paper detector 1 Manual feed paper detector 2 Manual feed paper width detector Manual feed paper length detector 1 Manual feed paper length detector 2 Paper feed tray 2 paper detector 1 Paper feed tray 2 paper detector 2 Manual tray pull-out position detector 1 Manual tray pull-out position detector 2 Paper detector 2

Paper empty detection (Paper feed tray 3) Paper feed tray 3 paper detection Paper tray upper limit detection (Paper feed tray 4) Paper empty detection (Paper feed tray 4) Paper feed tray 4 paper detection Manual paper feed tray paper empty detection Manual tray paper detection

POD1

POD1

Paper exit detector 1

Manual paper feed tray paper length detection (Paper feed side) Manual paper feed tray paper length detection (Outside) Manual feed/paper feed tray 2/ LCC paper detection Manual feed/paper feed tray 2/ LCC paper detection Manual paper feed tray pull-out position detection (Storing position) Manual paper feed tray pull-out position detection (Pull-out position) Paper detection (Left door unit) from duplex (ADU)/ No.1, 3, 4 paper feed Paper exit detection from fusing

POD2

POD2

Paper exit detector 2

Paper detection from paper exit

POD3

POD3

Paper exit detector 3

Paper exit detection to upper section paper exit tray (Full detection)

PPD

PPD

SPED1

SPED1

Paper detection in front of resist roller DSPF document empty detection

SPED2

SPED2

Resist roller front paper detector DSPF document empty detector DSPF document detector

DSPF document detection

SPLS1

SPLS1

SPLS2

SPLS2

SPOD

SPOD

DSPF document length detector 1 DSPF document length detector 2 DSPF paper exit detector

DSPF document length detection (Short) DSPF document length detection (Long) DSPF paper exit detection

SPPD1

SPPD1

SPPD2

SPPD2

SPPD3

SPPD3

SPPD4

SPPD4

SPWS

SPWS

STLD

STLD

STUD

STUD

T1LUD

T1LUD

T1PED

T1PED

T1PPD

T1PPD

DSPF document paper detector 1 DSPF document paper detector 2 DSPF document paper detector 3 DSPF document paper detector 4 DSPF document size (Width) detection analog data detector DSPF document tray lower limit detector DSPF document tray upper limit detector Paper feed tray upper limit detector (Paper feed tray 1) Paper empty detector (Paper feed tray 1) Paper detector (Paper feed tray 1)

Type

Connector level “L” “H” Paper Paper empty present Paper – – Upper limit detection Paper Paper empty present Paper – Paper Paper present empty Paper – Paper – – –

Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Volume resistor Transmission type Transmission type Transmission type Transmission type type

Paper Paper Storage

type

Pull-out

–

Transmission type

Paper

–

Transmission type Transmission type Transmission type

Paper Paper –

–

Paper Paper present Paper present

DSPF document paper detection 1 DSPF document paper detection 2 DSPF document paper detection 3 DSPF document paper detection 4 DSPF document size (Width) detection DSPF document tray lower limit detection DSPF document tray upper limit detection Paper feed tray upper limit (Paper feed tray 1)

Reflection type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Volume resistor Transmission type Transmission type Transmission type

Paper presence detection (Paper feed tray 1) Paper detection from paper feed tray 1

Transmission type Transmission type

Manual tray and LCC paper detection Manual feed paper width detection

– –

Paper present Paper present – – –

– Paper (Full detection) –

NOTE Paper feed tray system sensor Paper transport system sensor Paper feed tray system sensor Paper feed tray system sensor Paper transport system sensor Manual paper feed unit Paper transport system sensor Paper transport system sensor Analog detector Manual paper feed unit Manual paper feed unit Paper transport system sensor Paper transport system sensor Manual paper feed unit Manual paper feed unit Paper transport system sensor Paper transport system sensor Paper transport system sensor Paper transport system sensor Paper transport system sensor Sensor Sensor

Paper present Paper present

Sensor Sensor

Paper exit

Sensor

Paper present Paper present Paper present Paper present –

Sensor

Upper limit

Paper empty Paper

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 7

Sensor Sensor Sensor –

Other detector

Lower limit

Sensor

Upper limit

Sensor

–

Paper present –

Paper feed tray system sensor Paper feed tray system sensor Paper transport system sensor

Code

Signal name

T2LUD

T2LUD

T2PED

T2PED

Name

Function/Operation

Paper feed tray upper limit detector (Paper feed tray 2) Paper empty detector (Paper feed tray 2)

Connector level “L” “H” Upper limit –

Type

Paper feed tray upper limit (Paper feed tray 2) Paper presence detection (Paper feed tray 2)

Transmission type Transmission type

Paper empty

Paper present

NOTE Paper feed tray system sensor Paper feed tray system sensor

SCOV

SOCD

LEDX

MHPS

OCSW

PDSELX

TH-EX

WEBEND

RTH1 RTH2

TH-CL

RTH3 DSW-ADU

TH-RA

HUS-TC

PCS DSW-L

DSW-F DMS DSW-R

TLS TFSD TNCA TCS HUS-DV TH-DV

THPS2

T2SPD T1SPD DSW-DSK TANSET

M1SS1 M1PWS

M1SPD

M1SS3 M2SS1

M2SPD

Code CISTH DMS

Signal name CISTH DMS

Name CIS temperature sensor OPC drum marking sensor

Function/Operation CIS temperature detection OPC drum mark detection

M2SS3

Type Thermistor Reflection type

M1SS2 M1SS4 M2SS2 M2SS4

Connector level “L” “H” – – – –

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 8

NOTE Not used. Analog detector

Code

Signal name

Name

Function/Operation

Type

DSWADU

DSWADU

Duplex (ADU) cover open/ close detector

Duplex (ADU) cover open/close detection

Transmission type

DSW-DSK

DSW-DSK

DSW-F

DSW-F

Left door open/close detector (Desk section) Front door open/close detector

Left door open/close detection (Desk section) Front door open/close detection

Transmission type Micro switch

DSW-L

DSW-L

Left door open/close detector

Left door open/close detection

Micro switch

DSW-R

DSW-R

Manual feed open/close detector

Manual feed open/close detection

Micro switch (NC)

HUS-DV

HUS-DV

HUS-TC

HUS-TC

Developing humidity sensor Process humidity sensor

LEDX

LEDX

Developing section peripheral humidity detection Process section peripheral humidity detection Document size detection LED

Humidity sensor Humidity sensor LED

M1PWS

M1PWS

Multi paper feed tray paper width detection (Paper feed tray 3)

M1SPD

M1SPD

M1SS1

M1SS1

M1SS2

Connector level “L” “H” Duplex Duplex (ADU) door (ADU) door open open close Desk left Desk left door open door close Front door Front door or left door or left door open close Left door, Left door, front door front door open, close manual manual paper feed paper feed unit pullout unit close Left door Manual unit open or insertion manual unit pulled out – –

NOTE Door switch

Door switch Door switch

Door switch

Door switch

Analog detector

–

–

–

–

Analog detector (Not used) Other detector

Slide resistor

–

–

Analog detector

Paper remaining quantity detection (Paper feed tray 3)

Transmission type

–

Remaining paper quantity 66% or less

Paper size detector (Paper feed tray 3)

Paper size detection by combination of ON/OFF of MISS 1 – 4

switch

M1SS2

Paper size detector (Paper feed tray 3)

Paper size detection by combination of ON/OFF of MISS 1 – 4

M1SS3

M1SS3

Paper size detector (Paper feed tray 3)

Paper size detection by combination of ON/OFF of MISS 1 – 4

M1SS4

M1SS4

Paper size detector (Paper feed tray 3)

Paper size detection by combination of ON/OFF of MISS 1 – 4

M2SPD

M2SPD

Paper remaining quantity detector (Paper feed tray 4)

Paper remaining quantity detection (Paper feed tray 4)

Transmission type

M2SS1

M2SS1

Paper size detector (Paper feed tray 4)

Paper size detection by combination of ON/OFF of MISS 1 – 4

switch

M2SS2

M2SS2

Paper size detector (Paper feed tray 4)

Paper size detection by combination of ON/OFF of MISS 1 – 4

Document size sensor (Light emitting) (LED) Paper feed tray paper width detector (Paper feed tray 3) Paper remaining quantity detector (Paper feed tray 3)

–

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 9

Remaining paper quantity 66% or less

Paper feed tray remaining quantity sensor Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Paper feed tray remaining quantity sensor Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).)

Code

Signal name

Name

Function/Operation

Type

M2SS3

M2SS3

Paper size detector (Paper feed tray 4)

Paper size detection by combination of ON/OFF of MISS 1 – 4

switch

M2SS4

M2SS4

Paper size detector (Paper feed tray 4)

Paper size detection by combination of ON/OFF of MISS 1 – 4

switch

MHPS

MHPS

Scanner home position detection

OCSW

OCSW

Scanner home position sensor detector DSPF open/close detector

PCS

PCS

Image density sensor

PDSELX

PDSELX

RTH1

RTH1

RTH2

RTH2

RTH3

RTH3

SCOV

SCOV

Document size sensor (Light reception) (PT) Heat roller temperature sensor (Center section) Heat roller temperature sensor (Edge section) Sub heat roller temperature sensor DSPF cover switch

Transmission type Transmission type Reflection type Photo transistor Thermistor

DSPF cover open/close detection

SOCD

SOCD

DSPF open/close detector

DSPF open/close detector

T1SPD

T1SPD

Paper remaining quantity detector (Paper feed tray 1)

Paper remaining quantity detection (Paper feed tray 1)

Transmission type Transmission type Transmission type

T2SPD

T2SPD

Paper remaining quantity detector (Paper feed tray 2)

Paper remaining quantity detection (Paper feed tray 2)

Transmission type

TANSET

TANSET

TCS

TCS

Paper feed tray 1/2 detection signal Toner density sensor

Paper feed tray 1, 2 (Tandem tray) insertion detection Toner density detection

TFSD

TFSD

Toner remaining quantity sensor

Toner hopper toner remaining quantity detection

Transmission type Magnetic sensor Magnetic sensor

TH-CL

TH-CL

TH-DV

TH-DV

OPC drum peripheral temperature detection Developing section humidity detection

TH-EX

TH-EX

OPC drum temperature sensor Developing humidity sensor Paper exit unit temperature sensor

TH-RA

TH-RA

Room temperature sensor

THPS2

THPS2

TLS

TLS

TNCA

TNCA

WEBEND

WEBEND

Transfer belt / separation home position sensor 2 Waste toner pipe lock detector Waste toner full detection signal WEB end sensor

Trigger for document size detection. Detection of density of toner patch on the OPC drum Document size detection Heat roller temperature detection (Center section) Heat roller temperature detection (Edge section) Sub heat roller temperature detection

Connector level “L” “H”

Home position Close

NOTE Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Multi paper feed tray vertical size detection (Refer to the separate table in the “[11] SIGNAL NAME LIST” (*1).) Sensor Sensor

–

–

Analog detector

–

–

Other detector

–

–

Analog detector

Thermistor

–

–

Analog detector

Thermistor

–

–

Analog detector

–

–

Pull-out

Close

Sensor

Close

Sensor

Remaining paper quantity 50% or less Remaining paper quantity 33% or less Insertion

Paper feed tray remaining quantity sensor Paper feed tray remaining quantity sensor Paper feed tray system sensor Analog detector

–

–

Remaining quantity great –

Remaining quantity small –

Analog detector

Thermistor/ humidity Thermistor

–

–

Analog detector

–

–

Analog detector

Thermistor

–

–

Transfer belt separation home position detection 2

Transmission type

–



Analog detector(Not used) Other sensor, switch

Waste toner pipe lock detection

Lead type

–

Lock (Tilt)

Waste toner full detection

Magnetic sensor Transmission type

–

End detection

Paper exit unit peripheral temperature detection (Cooling fan operation monitor) Room temperature detection

Detects the WEB paper end (replacement)

Thermistor

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 10

Other sensor, switch

Other sensor, switch Not used.

F. Switch

DSW-L

MPSW DSW-F MSW DSW-R WH-SW

MPSW MSW

Signal name MPSW MSW

DSW-F

DSW-F

DSW-L

DSW-L

DSW-R

DSW-R

WH-SW

WH-SW

Code

Name

Type

Main power switch Power switch

Seesaw switch Seesaw switch

Front door open/close detector Left door open/close switch Manual paper feed unit open/close switch

Micro switch

Dry heater switch

Seesaw switch

Micro switch Micro switch

Function/Operation Turns ON/OFF all the power sources. Turns ON/OFF the main DC power source. (Turns ON/ OFF the engine power source except for the sub DC power source.) Front door open/close detection, Main charger power source, Developing bias power line open/close Left door open/close detection, Main charger power source, Developing bias power line open/close Manual paper feed unit open/close detection, Main charger power source, Developing bias power line open/ close Turns ON/OFF the power line of the dry heater.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 11

NOTE

Shut-off solenoid built-in

G. Clutch/solenoid

SPFC SRRC

STRRC

SRRBC

STRRBC STRC STRBC

DGS PSPS

DSKLS MFPUS

RRC

MPFGS

PSBC T1PFC DSKPFC2

MPFC

T1PUS

HPFC

M1PUS

T2PFC

M1PFC

T2PUS

DSKPFC1 M2PFC M2PUS

DGS

Signal name DGS

Paper exit gate solenoid

Paper exit gate drive

DSKLS

DSKLS

Paper guide lock solenoid

Lock the horizontal transport paper guide

DSKPFC1

DSKPFC1

DSKPFC2

DSKPFC2

HPFC

HPFC

Paper feed tray 3/4 paper transport clutch 1 Paper feed tray 3/4 paper transport clutch 2 Horizontal paper transport clutch

M1PFC

M1PFC

Paper feed tray 3/4 section paper transport roller ON/ OFF control Paper feed tray 3/4 section paper transport roller ON/ OFF control Manual paper feed, paper feed tray 2 section, LCC paper transport roller ON/OFF control Paper freed tray 3 section roller ON/OFF control

M1PUS

M1PUS

M2PFC

M2PFC

M2PUS

M2PUS

MFPUS

MFPUS

MPFC

MPFC

MPFGS

Code

Name

Function/Operation

MPFGS

Paper feed clutch (Paper feed tray 3) Paper pickup solenoid (Paper feed tray 3) Paper feed clutch (Paper feed tray 4) Paper pickup solenoid (Paper feed tray 4) Paper pickup solenoid (Manual paper feed) Paper feed clutch (Manual paper feed) Manual paper feed gate solenoid

Manual paper feed section paper feed roller ON/OFF control Manual feed gate solenoid open/close control.

PSBC

PSBC

Resist roller brake clutch

Resist roller braking

PSPS

PSPS

Separation solenoid

OPC drum separation pawl drive

RRC

RRC

Resist roller clutch

Resist roller ON/OFF control

SPFC

SPFC

DSPF paper feed clutch

DSPF paper feed section roller ON/OFF control

SRRC

SRRC

DSPF resist roller clutch

DSPF resist roller ON/OFF control

SRRBC

SRRBC

DSPF resist roller brake clutch

DSPF resist roller braking

Presses the paper pickup roller onto paper Paper freed tray 4 section roller ON/OFF control Presses the paper pickup roller onto paper Presses the paper pickup roller onto paper

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 12

Type Electromagnetic solenoid Electromagnetic solenoid Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic solenoid Electromagnetic clutch Electromagnetic solenoid Electromagnetic solenoid Electromagnetic clutch Electromagnetic solenoid Electromagnetic clutch Electromagnetic solenoid Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch

NOTE

STMPS

Signal name STMPS

STRBC

STRBC

STRC

STRC

STRRBC

STRRBC

STRRC

STRRC

T1PFC

T1PFC

T1PUS

T1PUS

T2PFC

T2PFC

T2PUS

T2PUS

Code

Name

Function/Operation

Stamp solenoid control signal

Stamp drive

DSPF paper transport roller 2 brake clutch DSPF paper transport roller 2 clutch

DSPF transport roller 2 braking

DSPF No. 1 resist roller breake clutch DSPF No. 1 resist roller clutch Paper feed clutch (Paper feed tray 1) Paper pickup solenoid (Paper feed tray 1) Paper feed clutch (Paper feed tray 2) Paper pickup solenoid (Paper feed tray 2)

Type

NOTE

Electromagnetic solenoid Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic solenoid Electromagnetic clutch Electromagnetic solenoid

DSPF transport roller 2 ON/OFF control DSPF transport roller 3 braking DSPF transport roller 3 ON/OFF control Paper freed tray 1 section roller ON/OFF control Presses the paper pickup roller onto paper. Paper feed tray 2 section roller ON/OFF control Presses the paper pickup roller onto paper.

H. Drive motor

SPSM SLUM POM1

SPFM

POM2

1

DVM MIM

FUM WEBM DM

PGM TM1 TM2

2 MM TURM

T1LUM TRM

M1LUM

VPM

M2LUM T2LUM

1

Signal name 1

Duplex (ADU) motor 1

Stepping motor

2

2

Duplex (ADU) motor 2

Stepping motor

DM

DM

OPC drum motor

DVM

DVM

Developing system

FUM

FUM

Fusing motor

M1LUM

M1LUM

Paper feed tray lift-up motor (Paper feed tray 3)

DC brush-less motor DC brush-less motor DC brush-less motor DC brush motor

Drives the lift plate of the paper feed tray.

M2LUM

M2LUM

Paper feed tray lift-up motor (Paper feed tray 4)

DC brush motor

Drives the lift plate of the paper feed tray.

Code

Name

Type

Function/Operation Drives the paper transport roller 2 and the paper transport roller 19. Drives the paper exit rollers 20 and 21.

NOTE High speed Selection of Normal speed/ High speed

Drives the OPC drum and the transfer section. Drives the developing section. Drives the fusing section.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 13

Selection of Rotation mode/ Brake mode Selection of Rotation mode/ Brake mode

MIM MM

Signal name MIM MM

Scanner (reading) motor Main motor

PGM

PGM

LSU motor

POM1

POM1

POM2

Code

Name

Type

Function/Operation

Paper exit motor 1

Stepping motor DC brush-less motor DC brush-less motor Stepping motor

Drives the paper transport roller 16.

POM2

Paper exit motor 2

Stepping motor

Drives the paper exit roller 1.

SLUM SPFM

/SLUM SPFM1

Stepping motor Stepping motor

Lifts up and down the DSPF paper feed tray. Drives the paper feed roller and the transport roller.

SPSM T1LUM

SPFM2 T1LUM

DSPF paper tray lift motor DSPF paper feed motor, paper transport motor DSPF paper exit motor Paper feed tray lift-up motor (Paper feed tray 1)

Stepping motor DC brush motor

Drives the paper exit roller. (DSPF) Drives the lift plate of the paper feed tray.

T2LUM

T2LUM

Paper feed tray lift-up motor (Paper feed tray 2)

DC brush motor

Drives the lift plate of the paper feed tray.

TM1

TM1

Toner motor 1

TM2

TM2

Toner motor 2

Transports toner in the toner hopper to the developing unit./ Transports waste toner to the waste toner section. Transports toner in the toner bottle to the toner hopper.

TRM

TRM

Resist roller front drive motor

Synchronous motor Synchronous motor Stepping motor

Drives the paper transport roller 15.

TURM

TURM

Transfer separation motor

DC brush motor

Drives and separates the transfer belt.

VPM

VPM

Vertical paper transport motor

Stepping motor

Drives the paper transport rollers 4 and 13.

WEBM

WEBM

WEB motor

Synchronous motor

Drives the WEB roller

NOTE

Drives the scanner (reading) section. Drives the paper feed trays 1, 2, 3, and 4, and the manual paper feed section. Drives the scanner (writing) (LSU) unit mirror.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 14

Selection of Normal speed/ High speed Selection of Normal speed/ High speed

Selection of Rotation mode/ Brake mode Selection of Rotation mode/ Brake mode

Normal speed mode/ Resist roller front paper transport timing control (Warp amount control) When executing the process correction and detecting a jam, the transfer belt is separated from the OPC drum. Normal speed mode

I. Lamp

CL1

LEDCL

CCFT

DL

CCFT

Signal name CCFT

LCD backlight

DL CL1

DL CL1

Discharge lamp Scanner lamp

Cold Cathode Fluorescent Tube Lamp Xenon lamp

LEDCL

LEDCL

CIS lamp (LED)

LED

Code

Name

Type

Function/Operation Backlight for LCD Discharges electric charges on the OPC drum. Radiates lights onto a document for the CCD to scan the document image. Radiates lights onto a document for the CIS to scan the document image.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 15

NOTE

J. Fan motor

CFM-U1 CFM-U3 SPFFAN VFM-EX1

CFM-U4

VFM-EX2

CFM-U2

VFM-EX3

VFM-BKU VFM-BKR

CFM-R1 VFM-BKL CFM-R2 CFM-HDD

CFM-R3

CFM-DV CFM-ICU

CFM-DC1 CFM-DC2

CFM-DC1

Signal name CFM-DC1

Power cooling fan motor

CFM-DC2

CFM-DC2

Power cooling fan motor

CFM-DV

CFM-DV

Developing section cooling fan motor

CFM-HDD

CFM-HDD

HDD cooling fan motor

CFM-ICU

CFM-ICU

Controller cooling fan motor

CFM-R1

CFM-R1

Process cooling fan motor 1 (LSU/process section)

CFM-R2

CFM-R2

Process cooling fan motor 2 (LSU/process section)

CFM-R3

CFM-R3

Process cooling fan motor 3 (LSU/process section)

CFM-U1

CFM-U1

CFM-U2

CFM-U2

CFM-U3

CFM-U3

CFM-U4

CFM-U4

SPFFAN

SPFFAN

Fusing section cooling fan motor 1 (Paper exit/duplex (ADU) section) (Top surface) Fusing section cooling fan motor 2 (Paper exit/duplex (ADU) section) (Paper exit rear side) Fusing section cooling fan motor 3 (Paper exit/duplex (ADU) section) (Top surface) Fusing section cooling fan motor 4 (Paper exit/duplex (ADU) section) (Paper cooling fan motor) DSPF fan motor

VFM-EX1

VFM-EX1

Process exhaust fan motor 1 (Front side)

VFM-EX2

VFM-EX2

Process exhaust fan motor 2 (Center)

VFM-EX3

VFM-EX3

Process exhaust fan motor 3 (Rear side)

VFM-BKL

VFM-BKL

Process exhaust fan motor 4

VFM-BKR

VFM-BKR

Process exhaust fan motor

VFM-BKU

VFM-BKU

Paper cooling fan motor

Code

Name

Type DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor DC brush-less motor

Function/Operation

NOTE

Cools the DC power unit. Cools the DC power unit. Cools the developing section. Cools the HDD. Cools the controller. Cools the LSU/ process section. Cools the LSU/ process section. Cools the LSU/ process section. Exhaust heat from the fusing section. Exhaust heat from the fusing section. Exhaust heat from the fusing section. Cools paper which is discharged to the inner tray. Exhausts heat generated by the motor clutch in the DSPF. Exhaust ozone and heat from the process section. Exhaust ozone and heat from the process section. Exhaust ozone and heat from the process section. Exhaust ozone and heat from the process section. Exhaust heat from the fusing section. Exhaust heat from paper in the inner tray.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 16

PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control PWM control

K. PWB (Main unit section)

6 14 7 3 20 13 24 15

26 17 25 2 5

32

22 16 23 10 11 29

18 9 27 28 8

12 31 4

19

30

1 21

No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Name AC power PWB CCD PWB CIS control PWB/CIS unit DC main power PWB DC sub power PWB LVDS PWB LCD INV PWB MFP FLASH ROM PWB MFP controller PWB Mother PWB PCU FLASH ROM PWB PCU PWB DSPF PWB DSPF paper width detection PWB Image density sensor PWB OPC drum mark sensnor PWB Document size detection light reception PWB Document size detection light emitting PWB High voltage power PWB (MC/DV/TC)

20 21 22 23 24 25

Transfer bias high voltage PWB (TD CL) Dehumidifier heater relay PWB Discharge lamp PWB Scanner Flash PWB Scanner control PWB Scanner relay PWB

26 27 28 29 30

Operation control PWB Soft NIC PWB Manual feed paper width detection PWB Driver PWB Paper size detection PWB (Paper feed tray 3, 4) Detector PWB (Paper feed tray 1, 2) Photoconductor temperature sensor PWB

31 32

Function/Operation Controls the AC power. Scans document images to converts analog signal to digital signal. Scans document images (back surface) and controls the CIS unit. Generates the DC power. Generates the DC power in the power save mode. Generates the LCD display signal. Generates a high voltage for backlight. Stores the MFP control program. Controls the image-related items and controls all over the machine. Interfaces the MFP control PWB and the PCU PWB. Stores the PCU control program. Controls the engine section. Drives the DSPF section loads./ Interfaces the sensor and detector signals. Detects the DSPF paper tray paper width. Detects the toner patch density in the image density correction. Detects the OPC drum mark. Generates the document size detection signal. Generates lights to detect the document size. Generates the main charger voltage, the developing bias voltage, the transfer voltage and the transfer belt cleaning voltage. Provides the bias voltage for the transfer cleaning roller and the print mode. Controls ON/OFF of the dehumidifier heater. Generates light for discharging. Stores the scanner control program. Controls the scanner section. Interfaces the scanner control PWB, the CCD PWB, the operation control PWB and the LVDS/INV PWB. Controls the display operation . Controls the network. Detects the manual paper feed tray paper width. Drives the motors. Detects the paper size. Detects the paper empty and upper limit tray. Temperature detection around the photoconductor

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 17

NOTE

L. FAX section

4,5

1 3

No 1 2

MDMC PWB FAX IF PWB

Name

3

TEL/LIU PWB

4 5

FAX AC power 100 FAX AC power 200

Function/Operation Controls the Modem and the TEL/LIU PWB. • Interfaces the MDMC PWB and the main unit controller PWB. • Installs the FAX image memory. (Expansion memory can be installed.) • Controls the line. (Call-out, polarity reversion detection, CI detection, line monitor, etc.) • Connection of an externally connected telephone line. Generates the FAX DC power of 100V. Generates the FAX DC power of 200V.

MODEL Modem control

NOTE Fax unit

M. Fuse/thermostat

24 23

15

22 14

13

8 5 6 7 1 2 3 4

17, 20 16, 19 18, 21

10

11

9,12

No. 1

Code F201

Name Fuse

Type Time lag

Specifications 250V 6.3A

Function/Operation PCU PWB protection (24V1)

2

F202

Fuse

Time lag

250V 6.3A

Driver PWB protection (24V2)

3

F203

Fuse

Time lag

250V 6.3A

Scanner control PWB protection (24V3)

4

F204

Fuse

Time lag

250V 6.3A

LCC control PWB protection (24V4)

5

F205

Fuse

Time lag

250V 6.3A

Finisher protection (24V5)

6

F206

Fuse

Time lag

250V 6.3A

Inserter protection (24V6)

7

F207

Fuse

8

F208

Fuse

Not used. Time lag

250V 6.3A

Motor protection (38V)

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 18

Section DC main power PWB DC main power PWB DC main power PWB DC main power PWB DC main power PWB DC main power PWB DC main power PWB DC main power PWB

NOTE 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series 100V series/ 200V series

No. 9

F1

Code

Name Fuse

Type Time lag

Specifications 250V 15A

10

F2

Fuse

Time lag

250V 3.15A

11

F3

Fuse

Time lag

250V 5A

12

F1

Fuse

Time lag

250V 8A

13

F101

Fuse

Time lag

250V 2A

14

F102

Fuse

Time lag

250V 2A

15

F1

Fuse

250V 200mA

16

F1

Fuse

Immediate decision type Time lag

17

F3

Fuse

Time lag

250V 2.0A

MFP controller PWB power source protection (12V1, 5V1) DC power source overcurrent protection (Main source) DC power source overcurrent protection (Main source) DC power source overcurrent protection (Main source) LCD inverter circuit overcurrent protection LVDS/ INV AC power source overcurrent protection (Main source) Thermal heater overcurrent protection

18

F5

Fuse

Time lag

250V 2.5A

MSW detection circuit overcurrent protection

19

F1, F2

Fuse

Time lag

250V 10A

20

F3, F4

Fuse

Time lag

250V 2.0A

AC power source overcurrent protection (Main source) Thermal heater overcurrent protection

21

F5

Fuse

Time lag

250V 2.5A

MSW detection circuit overcurrent protection

22

HLTS1

Thermostat

23

HLTS2

Thermostat

24

HLTS3

Thermostat

120VAC 15A 240VAC 10A 120VAC 15A 240VAC 10A 120VAC 15A 240VAC 10A

250V 20A

Function/Operation DC power source overcurrent protection (Main source) Varistor overcurrent protection

Section DC main power PWB DC main power PWB DC main power PWB DC main power PWB DC sub power PWB DC sub power PWB LCD INV PWB

NOTE 100V series

100V system

Fusing roller overheat protection

AC power PWB EX100 AC power PWB EX100 AC power PWB EX100 AC power PWBEX200 AC power PWBEX200 AC power PWBEX200 Fusing unit

Fusing roller overheat protection

Fusing unit

Sub heat roller overheat protection

Fusing unit

N. Adjustment volume

RV102 RV201

RV202

Name RV102 RV201 RV202

Function/Operation DC sub power unit +12V power output voltage adjustment VR DC main power unit +38V power output voltage adjustment VR DC main power unit +24V power output voltage adjustment VR

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 19

NOTE

100V series/ 200V series 100V series/ 200V series 200V series 100V series/ 200V series 100V series/ 200V series Common

100V system 100V system 200V system 200V system 200V system

O. Gate

2 1

3

No. 1

Name Switchback gate

2

Paper exit gate

3

Manual feed gate

Function/Operation Selects the paper route when discharging paper to the inner tray and when switching back to the exit or finisher. Selects the paper route to transport paper to the duplex (ADU) section or to discharge paper. Specifies the lead edge position of paper when setting paper. (Prevention against double feed and multifeed of paper into the paper feed roller)

NOTE Switched not by the solenoid drive but by the automatic procedure. Driven by the solenoid (DGS).

P. Heater

WH1 SCN HL3 HL2 HL1

WH1 DESK WH2 DESK

Code HL1 HL2 HL3 WH1 DESK WH2 DESK WH1 SCN

Name Heater lamp 1 Heater lamp 2 Sub heater lamp Dry heater (Paper feed tray 1, 2) Dry heater (Paper feed tray 3, 4) Scanner dry heater

Type Halogen lamp Halogen lamp Halogen lamp Nichrome wire (18W)

Function/Operation Heats the center of the upper fusing roller. Heats the both ends of the upper fusing roller. Heats the fusing roller (pressing roller). Dehumidifies paper on the paper feed tray 1 and 2.

Nichrome wire (10W)

Dehumidifies paper on the paper feed tray 3 and 4.

Nichrome wire (7W)

Dehumidifies the scanner section.

NOTE

Service parts

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 20

Q. Lock position

1 6

7

2

3

4 5

No. 1 2 3 4 5 6

7

Name Scanner lock screw Paper tray 1 lock block Paper tray 2 lock block Paper tray 3 lock block Paper tray 4 lock block Fusing pressure release screw

Function/Operation Locks the scanner. (Protects the scanner unit from breakage during transit.) Locks the paper lift plate Locks the paper lift plate Locks the paper lift plate Locks the paper lift plate Applies and releases pressure in the fusing unit.

OPC drum separation pawl lock block

Protects the OPC drum from with the separation pawl.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 21

NOTE Be sure to lock during transit.

Release the pressure when storing the machine longer than 30 days.

R. Roller 47 46 58 57 44 45 56 55

76 75

74 73 72 71 65 66 64

70 69 68 67

83 84 85 86 77 82 78 79

63 61 62 48 49 59 60 17 16 50 51 43 42 41 53 52 54 40 39 38 4 6 37

2 3 81 80

18 19 20 21 9 7 8 22 23 24 25 12 10 11

36 5 34 35 33 31 32

No. 1 2 3 4 5 6 7 8 9 10

1

Name Paper feed roller (Manual paper feed tray) Separation roller (Manual paper feed tray) Paper pickup roller (Manual paper feed tray) Paper feed roller (No. 1 paper feed tray) Paper pickup roller (No. 1 paper feed roller) Separation roller (No. 1 paper feed tray) Paper feed roller (No. 2 paper feed tray) Separation roller (No. 2 paper feed tray) Paper pickup roller (No. 2 paper feed roller) Paper feed roller (No. 3 paper feed tray)

29

30

28

26

27 14 13

15

Function/Operation Feeds paper to the paper transport section. Separates paper to prevent double-feed. Sends paper to the paper transport section. Feeds paper to the paper transport section. Sends paper to the paper transport section. Separates paper to prevent double-feed. Feeds paper to the paper transport section. Separates paper to prevent double-feed. Sends paper to the paper transport section. Feeds paper to the paper transport section.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 22

NOTE

No. 11

16

Name Separation roller (No. 3 paper feed tray) Paper pickup roller (No. 3 paper feed roller) Paper feed roller (No. 4 paper feed tray) Separation roller (No. 4 paper feed tray) Paper pickup roller (No. 4 paper feed roller) Resist roller (Drive)

17 18 19 20

Resist roller (Idle) Transport roller 1 (Drive) Transport roller 1 (Idle) Transport roller 2 (Drive)

21

Transport roller 2 (Idle)

22

Transport roller 3 (Drive)

23 24 25 26 27 28 29 30

Transport roller 3 (Idle) Transport roller 4 (Drive) Transport roller 4 (Idle) Transport roller 5 (Drive) Transport roller 5 (Idle) Transport roller 6 (Idle) Transport roller 7 (Drive) Transport roller 7 (Idle)

31 32

Transport roller 8 (Drive) Transport roller 8 (Idle)

33 34 35

Transport roller 9 (Idle) Transport roller 10 (Drive) Transport roller 10 (Idle)

36 37

Transport roller 11 (Drive) Transport roller 11 (Idle)

38 39 40

Transport roller 12 (Idle) Transport roller 13 (Drive) Transport roller 13 (Idle)

41 42 43

Transport roller 14 (Idle) Transport roller 15 (Drive) Transport roller 15 (Idle)

44 45

Transport roller 16 (Drive) Transport roller 16 (Idle)

46 47 48 49

Transport roller 17 (Idle) Transport roller 18 (Idle) Transport roller 19 (Drive) Transport roller 19 (Idle)

50 51

Transport roller 20 (Drive) Transport roller 20 (Idle)

52 53

Transport roller 21 (Drive) Transport roller 21 (Idle)

54 55 56

Transport roller 22 (Idle) Paper exit roller 1 (Drive) Paper exit roller 1 (Idle)

57 58

Paper exit roller 2 (Drive) Paper exit roller 2 (Idle)

59 60 61 62

Transfer drive roller (Drive) Transfer roller (Idle) Fusing roller (Pressing) Sub heat roller

12 13 14 15

Function/Operation Separates paper to prevent double-feed. Sends paper to the paper transport section. Feeds paper to the paper transport section. Feeds paper to the paper transport section. Sends paper to the paper transport section. Transports paper to the transfer section. / Controls the paper transport timing and adjusts the relative relationship between the image and paper. Applies pressure to paper and the resist roller to transport the paper. Transports paper fed from the large capacity tray (LCC) to the transport roller 2. Applies pressure to paper and the resist roller to transport the paper. Transports paper transported from the manual paper feed and the transport roller 1 to the transport roller 3. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper transported from the paper teed tray 2 and the transport roller 2 to the transport roller 3. Applies pressure to paper and the resist roller to transport the paper. Transports paper transported from the transport roller 3 to the transport roller 15. Applies pressure to paper and the resist roller to transport the paper. Transports paper fed from the paper feed tray 4 to the transport rollers 6 and 7. Applies pressure to paper and the resist roller to transport the paper. Reduces friction between paper and the paper guide. Transports paper transported from the transport roller 5 to the transport roller 10. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper transported from the paper feed tray 3 to the transport rollers 9 and 10. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Reduces friction between paper and the paper guide. Transports paper transported from the transport rollers 7 and 8 to the transport roller 11. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper transported from the transport roller 10 to the transport roller 13. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Reduces friction between paper and the paper guide. Transports paper fed from the paper feed trays 1, 3, and 4 to transport roller 15. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Reduces friction between paper and the paper guide. Transports paper to the transport resist roller. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper from the fusing roller to the paper exit roller 1. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Reduces friction between paper and the paper guide. Reduces friction between paper and the paper guide. Transports paper from the transport from the paper exit roller 2 to the transport roller 20. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper transported from the transport roller 19 to the transport roller 21. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Transports paper transported from the transport roller 20 to the transport roller 15. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Reduces friction between paper and the paper guide. Discharges paper to the paper exit tray. / Switches back paper. Applies a pressure to paper and the paper exit roller to provide a transport power of the paper exit roller to paper. Discharges paper. / Transports paper to the duplex (ADU) section. Applies a pressure to paper and the transport roller to provide a transport power of the paper exit roller to paper. Drives the transfer belt. Helps to stretch the transfer belt. Applies a pressure to the fusing roller (heating). Heats the fusing roller (pressing).

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 23

NOTE

No. 63 64 65 66 67 68

Name Fusing roller (Heating) Paper feed roller (DSPF) Separation roller (DSPF) Paper pickup roller (DSPF) Transport roller 1 (Drive) (DSPF) Transport roller 1 (Drive) (DSPF)

69 70

First resist roller (Drive) (DSPF) First resist roller (Idle) (DSPF)

71 72

Transport roller 2 (Drive) (DSPF) Transport roller 2 (Idle) (DSPF)

73 74

Second resist roller (Drive) (DSPF) Second resist roller (Idle) (DSPF)

75 76

Paper exit roller (Drive) (DSPF) Paper exit roller (Idle) (DSPF)

77 78 79 80 81

Transfer cleaning roller Transfer tension roller Transfer roller Transfer roller 1A (Drive) Transfer roller 1A (Idle)

82 83 84

Cleaning brush roller Paper exit roller 3 (Drive) Paper exit roller 3 (Idle)

85 86

Pressure connect roller WEB roller

Function/Operation Heat and press toner onto paper to fuse images. Feeds paper to the paper transport section. Separates paper to prevent against double feed. Sends paper to the paper transport section. Transports paper (which is transported by the first resist roller) to the second resist roller. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Controls the paper transport timing. / Adjusts paper to be horizontal. Applies a pressure to paper and the resist roller to provide a transport power of the resist roller to paper. Transports paper transported from the paper exit roller 1 to the transport roller 3. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Controls the paper transport timing. / Adjusts paper to be horizontal. Applies a pressure to paper and the resist roller to provide a transport power of the resist roller to paper. Discharges paper. Applies a pressure to paper and the paper exit roller to provide a transport power of the paper exit roller to paper. Cleans the transfer belt. Applies a proper tension to the transfer belt. Applies a proper voltage to the transfer belt. Transports paper (which is fed from the manual paper feed tray) to the transport roller. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Removes paper dust from the photoconductor drum. Discharges paper to the paper exit tray. /Switches back paper. Applies a pressure to paper and the transport roller to provide a transport power of the transport roller to paper. Applies a pressure to WEB paper to connect with the heat roller. Clean the heat roller.

NOTE

S. Filter

1

2

No. 1 2

Name Ozone filter Toner filter

Function/Operation Absorbs ozone generated in the image process section. Filters dispersed toner in the process section.

MX-M700N EXTERNAL VIEW AND INTERNAL STRUCTURE 5 – 24

NOTE

MX-M700N [6] ADJUSTMENTS

5GTXKEG/WCN

1. General 2. Outline Each adjustment item in the adjustment item list is associated with a specific JOB number. Perform the adjustment procedures in the sequence of Job numbers from the smallest to the greatest. However, there is no need to perform all the adjustment items. Perform only the necessary adjustments according to the need. Unnecessary adjustments can be omitted. Even in this case, however, the sequence from the smallest to the greatest JOB number must be observed. If the above precaution should be neglected, the adjustment would not complete normally or trouble may occur.

3. Adjustment item list Job No ADJ 1

Adjusting high voltage values

ADJ 2

Adjusting the developing unit

ADJ 3

Adjusting image distortions

ADJ 4

Adjusting DSPF parallelism

ADJ 5

Adjusting the image focus

ADJ 6

Adjusting the image magnification

ADJ 1A ADJ 1B ADJ 1C ADJ 2A ADJ 2B ADJ 3A ADJ 3B ADJ 3C ADJ 3D ADJ 3E ADJ 4A ADJ 4B ADJ 5A ADJ 5B ADJ 6A ADJ 6B ADJ 6C ADJ 6D

ADJ7

Adjusting the image off-center

ADJ8

Adjusting the image position, image loss, and void area

ADJ9

Adjusting the copied image quality

ADJ10

Adjusting the print quality in fax mode

ADJ11

Adjusting the image quality in scan mode

ADJ12

Common image quality adjustments for all of copy, scan, and fax modes

ADJ 6E ADJ 7A ADJ 7B ADJ 7C ADJ 7D ADJ 8A ADJ 8B ADJ 8C ADJ 8D ADJ 8E ADJ 9A ADJ 9B ADJ 9C ADJ 9D ADJ 9E ADJ 9F ADJ10A ADJ10B ADJ10C ADJ10D ADJ10E ADJ10F ADJ11A ADJ11B ADJ11C ADJ11D ADJ11E ADJ11F ADJ12A ADJ12B

Adjustment item list Adjust the main charger grid voltage Adjust the developing bias voltage Adjust the transfer current, voltage Adjust the developing doctor gap Adjust the developing roller main pole Adjust print image distortions (LSU parallelism adjustment) Adjust the scanner (reading) unit parallelism Adjust scanned image distortions in the sub-scanning direction Adjust scanned image distortions in the main scanning direction – 1 Adjust scanned image distortions in the main scanning direction – 2 Adjust DSPF levelness Adjust DSPF skews Adjust the image focus in original table mode and DSPF front-face mode (CCD) Adjust the image focus in DSPF back-face mode (CIS) Adjust the image magnification in the main scanning direction in original table mode (CCD) Adjust the image magnification in the sub-scanning direction in original table mode (CCD) Adjust the image magnification in the main scanning direction in DSPF front-face mode (CCD) Adjust the image magnification in the main scanning direction in DSPF back-face mode (CIS) Adjust the image magnification in the sub-scanning direction in DSPF mode Adjust the print image off-center (print engine section) Adjust the scanned image off-center in original table mode (scan section) Adjust the scanned image off-center in DSPF front-face mode (scan section) Adjust the scanned image off-center in DSPF back-face mode (scan section) Adjust copied image loss/void area in original table mode Adjust the original scan start position (adjust the scanner read position in DSPF-mode front face scan) Adjust the copied image loss/void area in DSPF mode Adjust the image loss in scanner mode Adjust the image loss for images sent in fax mode Adjust the binary mode copy density for all modes at once Adjust the copy density in text binary mode Adjust the copy density in text/photo binary mode Adjust the copy density in photo binary mode Adjust the copied image gamma in copy mode Adjust the copied image sharpness Adjust the fax mode print density for all modes at once Adjust the fax mode print density in standard mode Adjust the fax mode print density in small-character mode Adjust the fax mode print density in fine mode Adjust the fax mode print density in super fine mode Adjust the fax mode print density in 600dpi mode Adjust the scan mode image density for all modes at once Scan mode image density adjustment/individual setup (standard mode) Scan mode image density adjustment/individual setup (small-character mode) Scan mode image density adjustment/individual setup (fine mode) Scan mode image density adjustment/individual setup (super fine mode) Adjust the image gamma in scanner mode Correct the image density in original table mode/DSPF mode (Copy mode) Set up the auto mode operation for copy, scan, and fax

MX-M700N ADJUSTMENTS 6 – 1

Simulation 8-2 8-1 8-6, 8-17, 8-18

64-1

64-1 48-1 48-1 48-1 48-1 48-1 48-1, 48-5 50-5 (50-10) 50-12 50-12 50-12 50-1 53-8 50-6 50-27 50-27 46-2 46-9, 10, 11

46-18 46-31 46-12 46-13, 46-14, 46-15, 46-16, 46-45

46-21 46-21, 46-22, 46-23, 46-24, 46-25

46-27 46-20 46-19

Job No ADJ13 ADJ14

ADJ15

ADJ16 ADJ17

Adjustment item list Adjusting the fusing paper guide position Adjusting the paper size detection ADJ14A ADJ14B ADJ14C Adjusting the original size ADJ15A detection (in original table mode) ADJ15B Adjusting the touch coordinates Adjusting the supply voltage

Simulation

Adjust the paper width sensor for the manual paper feed tray Adjust the paper width sensor for paper feed tray 3 Adjust the paper width sensor for the DSPF paper feed tray Adjust the detection point of the original size sensor (in original table mode) Adjust the sensitivity of the original size sensor

40-2 40-12 53-6 41-1 41-2 65-1

4. Datails of adjustment

ADJ 1 Adjusting high voltage values NOTE: Adjusting the output voltage requires the ability to measure internal impedance of 1000 :. In addition, use high voltage probe together. (FLUKE87FLUKE80K-40 is recommended.)

1-A Adjust the main charger grid voltage This adjustment is needed in the following situations: * The high voltage power PWB (MC/DV/TC) has been replaced. * U2 trouble has occurred. * The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. (Main charger grid voltage adjustment) Item/operation mode Copy

Printer FAX

Auto mode Text mode Text/photo mode Photo mode All modes All modes

8-2

AUTO CHARACTER MIX PHOTO PRINTER FAX

Simulation Setting range 200 – 1000 200 – 1000 200 – 1000 200 – 1000 200 – 1000 200 – 1000

1)

Remove the rear cover of the machine.

2)

Apply a digital multi-meter to the connector CN2 pin (3) of the high voltage PWB and the chassis GND.

Default 580 580 580 580 580 580

High voltage power PWB (MC/DV/TC) Connector Pin # Actual voltage CN2 3 -590r2v CN2 3 -590r2v CN2 3 -590r2v CN2 3 -590r2v CN2 3 -590r2v CN2 3 -590r2v

SIMULATION 8-2 MAIN GRID SETTING. INPUT VALUE, AND PRESS START. 1.AUTO (200-1000)

580 CN2 Press [START] key.

Press [SYSTEM SETTINGS] key. Or after 30sec output.

3 SIMULATION 8-2 MAIN GRID SETTING. EXECUTING···. 1.AUTO

3)

Go through the modes specified in Simulation 8-2.

SIMULATION 8-2 MAIN GRID SETTING. SELECT 1-6, AND PRESS START. 1.AUTO 580 2.CHARACTER 580 3.MIX 580 4.PHOTO 580 5.PRINTER 580 6.FAX 580

4)

Select the number that corresponds to the adjustment item using the numeric keypad.

5)

Press the Start key.

6)

Press the start key to have the voltage output for 30 seconds. The operation can be stopped with the SYSTEM SETTINGS key. If the output voltage is not within the requirement, do the following steps.

1

Press [START] key.

Press [SYSTEM SETTINGS] key.

580

7)

Enter the adjustment value using the numeric keypad.

8)

Press the Start key. (The adjustment value is put into memory, and the corresponding voltage is output for 30 seconds.)

Repeat steps 7 to 8 until the output requirement is satisfied.

MX-M700N ADJUSTMENTS 6 – 2

1-B Adjust the developing bias voltage This adjustment is needed in the following situations: * The high voltage power PWB (MC/DV/TC) has been replaced. * U2 trouble has occurred. * The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. (Main charger grid voltage adjustment) Simulation Setting range 0 – 750 0 – 750 0 – 750 0 – 750 0 – 750 0 – 750 0 – 250

Item/operation mode Copy

Printer FAX Cleaning mode

Auto mode Text mode Text/photo mode Photo mode All modes All modes

8-1

AUTO CHARACTER MIX PHOTO PRINTER FAX PLUS

1)

Remove the rear cover of the machine.

2)

Apply a digital multi-meter to the connector CN2 pin (7) of the high voltage PWB and the chassis GND.

High voltage power PWB (MC/DV/TC) Connector Pin # Actual voltage CN2 7 –500r5v CN2 7 –500r5v CN2 7 –500r5v CN2 7 –500r5v CN2 7 –500r5v CN2 7 –500r5v CN2 7 +500r5v

Default 495 495 495 495 495 495 150

SIMULATION 8-1 DV BIAS SETTING. INPUT VALUE, AND PRESS START. 1:AUTO (0-750)

495

CN2 Press [START] key.

3

Press [SYSTEM SETTINGS] key. Or after 30sec output.

SIMULATION 8-1 DV BIAS SETTING. EXECUTING···. 1:AUTO

3)

Go through the modes specified in Simulation 8-1. SIMULATION 8-1 DV BIAS SETTING. SELECT 1-7, AND PRESS START. 1.AUTO 495 2.CHARACTER 495 3.MIX 495 4.PHOTO 495 5.PRINTER 495 6.FAX 495 7.PLUS 150

Press [START] key.

495

4)

Select the number that corresponds to the adjustment item using the numeric keypad.

5)

Press the Start key.

6)

Press the start key to have the voltage output for 30 seconds. The operation can be stopped with the SYSTEM SETTINGS key. If the output voltage is not within the requirement, do the following steps.

1

Press [SYSTEM SETTINGS] key.

7)

Enter the adjustment value using the numeric keypad.

8)

Press the Start key. (The adjustment value is put into memory, and the corresponding voltage is output for 30 seconds.)

Repeat steps 7 to 8 until the output requirement is satisfied.

1-C Adjust the transfer current, voltage (Transfer voltage adjustment) Item/ operation mode Front print

8-6

Back print Transfer belt (cleaning)

8-17

Transfer roller (cleaning) Transfer roller (print)

8-18

Simulation Setting range FRONT 0 – 800

Default

BACK

0 – 800

SHV FRONT SHV BACK THVCRHV PLUS

0 – 600 0 – 600 0 – 75 0 – 250

350 400 * 350 400 * 450 450 10 200

CRHV MINUS

0 – 250

200

Adjustment voltage (monitor voltage)

Connector

Pin #

–

–

–

–

–

–

– – DC – 100r10v +2.0r10.1v

– – CN2 –

– – 1 Check pin

–2.0r10.1v

–

Check pin

* MX-M700 only

MX-M700N ADJUSTMENTS 6 – 3

Actual voltage /actual current 35r1.0PA (1.0 – 1.5Kv) 40r1.0PA (2.0 – 2.5Kv) * 35r1.0PA (1.0 – 1.5Kv) 40r1.0PA (2.0 – 2.5Kv) * AC4.5Kv (p-p) AC4.5Kv (p-p) DC –100r10v/AC4.5Kv (p-p) +2000r100v

–2000r100v

High voltage power PWB (MC/DV/TC)

High voltage power PWB (TC cleaning)

Transfer voltage adjustment (print operation mode)

3)

Go through the modes specified in Simulation 8-17.

This adjustment is needed in the following situations: * The high voltage power PWB (MC/DV/TC) has been replaced.

SIMULATION 8-17 TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START. 1.SHV FRONT 450 2.SHV BACK 450 3.THV- 10

* U2 trouble has occurred.

1

* The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. 1)

Go through the modes specified in Simulation 8-6. Press [START] key.

SIMULATION 8-6 THV+ SETTING. SELECT 1-2, AND PRESS START. 1.FRONT 400 2.BACK 400

1

SIMULATION 8-17 TRANSFER ROLLER SETTING. INPUT VALUE, AND PRESS START. 1.FRONT (0-600)

55ppm/62ppm = 350

Press [START] key.

Press [SYSTEM SETTINGS] key.

450

Press [SYSTEM SETTINGS] key.

Press [START] key.

SIMULATION 8-6 THV+ SETTING. INPUT VALUE, AND PRESS START. 1.FRONT(0-800)

Press [SYSTEM SETTINGS] key. Or after 30sec output.

400 SIMULATION 8-17 TRANSFER ROLLER SETTING. EXECUTING···. 1.FRONT(0-600)

55ppm/62ppm = 350

Press [START] key.

Press [SYSTEM SETTINGS] key. Or after 30sec output.

SIMULATION 8-6 THV+ SETTING. EXECUTING···. 1.FRONT

4)

Select the number that corresponds to the adjustment item (SHV FRONT / SHV BACK) using the numeric keypad.

5)

Press the Start key.

6)

Set each adjustment item to the default value (enter the adjustment value and then press the Start key).

400

* The adjustment items (SHV FRONT / SHV BACK) correspond to the AC component of the 'transfer belt cleaning mode voltage' applied to the transfer roller, but this voltage component cannot be determined. If the voltage seems to be abnormal after setting the default adjustment value, therefore, the high voltage PWB (MC/DV/TC) should be replaced.

55ppm/62ppm = 350

2)

Select the number that corresponds to the adjustment item (FRONT/BACK) using the numeric keypad.

3)

Press the Start key.

4)

Enter the adjustment value (default) using the numeric keypad.

5)

Press the Start key. (The adjustment value is put into memory, and the corresponding current is output for 30 seconds.)

7)

Transfer voltage adjustment (transfer belt cleaning mode) This adjustment is needed in the following situations:

Select the number that corresponds to cleaning operation mode (THV-) using the numeric keypad. * The adjustment items (THV-) corresponds to the DC component of the 'transfer belt cleaning mode voltage' applied to the transfer roller.

The operation can be stopped with the SYSTEM SETTINGS key. NOTE: It is not possible to determine the adjusted transfer voltage (print operation mode) (FRONT/BACK). If the voltage seems to be abnormal after setting the default value, therefore, the high voltage PWB (MC/DV/TC) should be replaced.

450

8)

Press the Start key.

9)

Press the Start key to have the voltage output for 30 seconds. If the output voltage is not within the requirement, do the following steps. The operation can be stopped with the SYSTEM SETTINGS key.

* The high voltage power PWB (MC/DV/TC) has been replaced.

10) Enter the adjustment value using the numeric keypad.

* U2 trouble has occurred.

11) Press the Start key.

* The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. 1)

Remove the rear cover of the machine.

2)

Apply a digital multi-meter to the connector CN2 pin (1) of the high voltage PWB and the chassis GND.

(The adjustment value is put into memory, and the corresponding voltage is output for 30 seconds.) Repeat steps 10 to 11 until the output requirement is satisfied.

(1) CN2

MX-M700N ADJUSTMENTS 6 – 4

Transfer voltage adjustment (transfer roller cleaning/transfer roller print modes)

4)

This adjustment is needed in the following situations:

Go through the modes specified in Simulation 8-18. SIMULATION 8-18 TRANSFER CLEANING ROLLER SETTING. SELECT 1-2, AND PRESS START. 1.CRHV PLUS 200 2.CRHV MINUS 200

* The high voltage power PWB (TC cleaning) has been replaced. * U2 trouble has occurred.

1

* The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. 1)

Connect the transfer section to the main body side using the transfer extension harness (DHAi-3629FCZZ).

Press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 8-18 TRANSFER CLEANING ROLLER SETTING. INPUT VALUE, AND PRESS START. 1.CRHV PLUS (0-250)

200

Press [START] key.

2)

Press [SYSTEM SETTINGS] key. Or after 30sec output.

SIMULATION 8-18 TRANSFER CLEANING ROLLER SETTING. EXECUTING···. 1.CRHV PLUS(0-250)

Remove the front frame cover of the duplex section, and remove the rear frame cover of the transfer section.

200

5)

Select the number that corresponds to the adjustment item (CRHV PLUS / CRHV MINUS) using the numeric keypad.

6)

Press the Start key.

7)

Press the Start key to have the voltage output for 30 seconds. The operation can be stopped with the SYSTEM SETTINGS key. If the output voltage is not within the requirement, do the following steps.

3)

Apply a digital multi-meter to the check pin of the high voltage PWB (TC cleaning) and the chassis GND.

8)

Enter the adjustment value using the numeric keypad.

9)

Press the Start key. (The adjustment value is put into memory, and the corresponding voltage is output for 30 seconds.)

Repeat steps 8 to 9 until the output requirement is satisfied.

ADJ 2 Adjusting the developing unit 2-A Adjust the developing doctor gap This adjustment is needed in the following situations: * The developing unit has been disassembled. * The print density is low. * The toner is excessively dispersed. 1)

Remove the developing unit of the machine.

2)

Remove the developing unit cover and blade cover.

MX-M700N ADJUSTMENTS 6 – 5

3)

Loosen the DV doctor fixing screws.

4)

Manually turn the DV roller to align the marking on the DV roller surface with the DV doctor position.

7)

On both sides of the DV doctor and at its center, make sure that the DV doctor gap is 0.525r0.03.

* When inserting a clearance gauge, take care not to damage the DV doctor or MG roller. Repeat steps 2 to 6 until the DV doctor gap meets the requirement.

2-B Adjust the developing roller main pole This adjustment is needed in the following situations: * The developing unit has been disassembled. * The print density is low. * The toner is excessively dispersed.

5)

Insert a 0.525mm clearance gauge in between the DV roller and DV doctor so that the gauge is positioned at a distance of 40 mm to 70 mm from the DV doctor end face.

1)

Remove the developing unit.

2)

Remove the developing unit cover and blade cover, and then place the developing unit on a level surface.

3)

Attach a piece of string to a sewing needle or pin.

4)

With the string in hand, bring the needle closer to the DV roller while keeping the needle parallel with the roller. (Do not use a clip, which does not accurately indicate the position.)

5)

Keeping the needle 2 to 3 mm off the DV roller surface, mark the DV roller surface at an extension of the needle tip. (Do not let the needle tip the DV roller.)

OO OO

OO OO

6)

Tighten the DV doctor fixing screws while pressing the DV doctor in the arrow direction. (This should be done for both front and rear frames.)

MX-M700N ADJUSTMENTS 6 – 6

6)

Measure the distance between the marking on the DV roller and leading edge of the DV doctor, and make sure that it is 19r0.5mm.

2)

Go through the modes specified in Simulation 64-1. SIMULATION 64-1 SELF PRINT MODE. SELECT 0. TRAY SELECT :1 1. 2. PRINT PATTERN:87 3. 4. MULTI : 1 5. 6. LEVEL : 1 7.

Select 1, and press [START] key.

(2)

19

Select other than 1, and press [START] key.

1

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (PRINT PATTERN) INPUT 1-98.

71

0.5 mm (3)

If this requirement is not met, do the following steps. 7)

0-7, AND PRESS START. PRINT START DENSITY :1 MODE :1 DUPLEX :1

SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (DENSITY) 1-255

100

Remove the front cover.

(4)

SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (MULTI COUNT) 1-999

1

(5)

8)

Loosen the fixing screws of the developing roller main pole adjusting plate, and make adjustments by moving the adjusting plate in the arrow direction.

(6)

SIMULATION 64-1 SELF PRINT MODE. SELECT (MODE) 1.STANDARD 2.SMOOTHING 5.SMOOTHING+ TONER SAVE 7.TONER SAVE+ HALF TONE 8.SMOOTHING+ TONER SAVE+

1-8, AND PRESS START. 3.TONER SAVE 4.HALF TONE 6.SMOOTHING+ HALF TONE

1

HALF TONE

SIMULATION 64-1 SELF PRINT MODE. INPUT VALUE, AND PRESS START. (LEVEL) 1-5

3

(0)

(7)

Repeat steps 3 to 6 until the developing roller main pole meets the positional requirement.

SIMULATION 64-1 SELF PRINT MODE. SELECT 1-2, AND PRESS START. (DUPLEX) 1.NO 2.YES

SIMULATION 64-1 SELFT PRINT MODE.. EXECUTING··· 0. TRAY SELECT :1 2. PRINT PATTERN:87 3. DENSITY 4. MULTI : 1 5. MODE 6. LEVEL : 1 7. DUPLEX

ADJ 3 Adjusting image distortions 3-A Adjust print image distortions (LSU parallelism adjustment)

SIMULATION 64-1 SELF PRINT MODE. SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

3)

:1 :1 :1

Select PRINT PATTERN using the numeric keypad.

This adjustment is needed in the following situations:

4)

Select print pattern 71 (grid pattern).

* The LSU has been replaced or removed.

5)

Press the Start key.

* Print images are distorted.

6)

Select PRINT START using the numeric keypad.

This adjustment should be followed by:

7)

Press the Start key.

ADJ 7 / ADJ 7A: Adjust the print image off-center (print engine section) 1)

Set A4 (11 x 8.5) paper to Tray 1.

MX-M700N ADJUSTMENTS 6 – 7

1

1

0

8)

Check the printed grid pattern for distortions.

11) Loosen the LSU fixing screws, and change the LSU fixing angle.

[Check Method 1] Compare the front frame side and rear frame side of the printed paper in of the distance between the outer end of the grid pattern image and the edge of the paper. No adjustment is needed if the difference between these dimensions is within 0.5 mm. R

* If the vertical line image is inclined to the left with respect to the front frame side, move the LSU fixing plate in arrow direction (a). * If the vertical line image is inclined to the right with respect to the front frame side, move the LSU fixing plate in arrow direction (b).

a

Ra-Fb

F

b

[Check Method 2] Check the printed grid pattern for distortions. If the right-angle level of the traverse print line is 0.5mm or less with respect to the longitudinal print line of paper, no adjustment is needed.

b a

Repeat steps 5 to 11 until an acceptable result is obtained.

3-B Adjust the scanner (reading) unit parallelism This adjustment is needed in the following situations: * The scanner (reading) section has been disassembled. * Scanned images are distorted. 1)

Loosen the fixing screws for Scanner Unit A and scanner drive wire to release the scanner unit from the drive wire.

Carry out the following work if the situation is unsatisfactory. 9)

Draw out the manual paper feed tray, and remove the front frame side, side cover, fan cover cabinet, and fan unit.

10) Remove the fan unit.

MX-M700N ADJUSTMENTS 6 – 8

2)

Manually turn the scanner drive pulley, and move Scanner Unit B until with the two stoppers on the CCD mounting plate. If Scanner Unit B makes with the two stoppers on the CCD mounting plate simultaneously, the parallelism of Scanner Unit B is proper.

8)

Without moving the scanner unit drive shaft, manually turn the scanner unit drive pulley so that Scanner Unit B makes with both of the two stoppers on the CCD mounting plate at the same time. (Change the positional relationship between the scanner unit drive pulley and the drive shaft.)

9)

With Scanner Unit B in with both of the two stoppers on the CCD mounting plate at the same time, align the end face of Scanner Unit A with the right-hand side end face of the frame, and fix Scanner Unit A with the screws. (Make positioning by using the ruler to right side of the scanner frame (F/R) and fix to the wire.)

If this requirement is not met, do the following steps. 3)

Loosen the pulley angle fixing screw on either the front or rear frame side of Scanner Unit B.

4)

Adjust the pulley angle position on Scanner Unit B so that the scanner unit makes with both of the two stoppers on the CCD mounting plate at the same time.

5)

Fix the pulley angle on Scanner Unit B. If the above steps fail to provide an acceptable result, then do the following steps.

6)

Loosen the fixing screw of the scanner unit drive pulley that is not in .

7)

Manually turning the scanner unit drive pulley, move Scanner Unit B until it comes into with the two stoppers on the CCD mounting plate. Scanner Unit B

Winding pulley

MX-M700N ADJUSTMENTS 6 – 9

4)

Loosen either of two fixing screws of the scanner unit drive pulley. (Either one on the front or the rear side will do.)

5)

With the scanner unit drive shaft kept stationary, manually turn the scanner unit drive pulley to change the parallelism of Scanner Units A and B. (Change the positional relationship between the scanner unit drive pulley and the drive shaft.)

6)

Tighten the scanner unit drive pulley fixing screw.

3-C Adjust scanned image distortions in the sub-scanning direction This adjustment is needed in the following situations: * The scanner (reading) section has been disassembled. * Scanned images are distorted. 1)

Make a test chart on A3 (11" x 17") paper as shown below. (Draw a rectangular with four right angles.)

L

L

L

L = 10mm L

2)

Set the test chart made in step 1 on the document table (about 30mm in front of the document standard setting position), and make a copy on A3 (11" x 17") paper with the DSPF unit open.

Repeat steps 2 to 6 until an acceptable result is obtained. 81 2

51 2 A5

B5

A4 A5

11 B5

13 A4

14

17 B4

A3

30mm

If the above steps fail to eliminate distortions in the sub scanning direction, do the steps described in "ADJ 3E: Adjust scanned image distortions in the main scanning direction –2".

3-D Adjust scanned image distortions in the main scanning direction – 1

51 2 A5

The scanner (reading) section has been disassembled.

B5

* Scanned images are distorted.

A5 A4 81 2

1)

B5 B4

11

A4 A3

Make a test chart on A3 (11" x 17") paper as shown below. (Draw a rectangular with four right angles.)

L

3)

Check for distortions in the sub scanning direction. If La = Lb, there is no distortion.

La

L

L

Lb L = 10mm L

2)

Set the test chart made in step 1 on the document table, and make a copy on A3 (11" x 17") paper.

If there is some distortion in the sub scanning direction, do the following steps.

MX-M700N ADJUSTMENTS 6 – 10

3)

Check for distortions in the main scanning direction. If the four angles of the rectangle on the copy are right angles, there is no distortion and therefore no further steps are needed.

3-E Adjust scanned image distortions in the main scanning direction – 2 This adjustment is needed in the following situations: * The scanner (reading) section has been disassembled. * Scanned images are distorted. 1)

Make a test chart on A3 (11" x 17") paper as shown below. (Draw a rectangular with four right angles.) L

L

L

If there is some distortion in the main scanning direction, do the following steps. 4)

Check the difference (distortion balance) between left-hand and right-hand side images distortions.

L = 10mm L

Lc

Lc

2)

Copy A

Set the test chart made in step 1 on the document table, and make a copy on A3 (11" x 17") paper.

Copy B 51 2

11

81 2 A5

B5

A4 A5

B5

13 A4

14

17 B4

A3

30mm Ld There is no difference between the distortion on the right and that on the left. Lc = Ld

Ld There is some difference between the distortion on the right and that on the left.

51 2 A5

B5

A5 A4 81 2

If Lc = Ld, the distortion on the left is equal to that on the right. (The distortions are balanced.)

B5 B4

11

A4 A3

If the above requirement is satisfied, then do the steps described in "ADJ 3E: Adjust scanned image distortions in the main scanning direction – 2". If the above requirement is not met, then do the following steps. 5)

Change the height balance of the front frame side scanner rail.

* If the paper leading edge is more distorted than the paper trailing edge, then raise the scanner rail right side. * If the leading edge is less distorted than the paper trailing edge, then lower the scanner rail right side. 6)

Set the test chart made in step 1 on the document table, and make a copy on A3 (11" x 17") paper.

7)

Check the image distortion balance in the main scanning direction.

3)

Check for distortions in the main scanning direction. If the four angles of the rectangle on the copy are right angles, there is no distortion and therefore no further steps are needed.

If there is some distortion in the main scanning direction, do the following steps. These steps assume that there is no or little difference in distortion between the paper's leading and trailing edges. If there is some difference in distortion between the paper's leading and trailing edges, these steps should be preceded by the adjustment steps described in "ADJ 3D: Adjust scanned image distortions in the main scanning direction - 1", intended to provide almost the same level of distortion on the leading and trailing edges.

Repeat steps 5 to 7 until the difference in size of image distortion (distortion balance) in the image scanning direction is equal.

MX-M700N ADJUSTMENTS 6 – 11

4)

Remove the document table glass, and make adjustments by turning the main scanning direction image distortion adjusting screw.

3)

Gently pulling out each check sheet for DSPF levelness adjustment, make sure that no gap is felt between the CIS guide boss and the glass for DSPF mode for each of the front and rear frame sides.

A B * If the rear frame side image is shifted toward the paper's leading edge, then turn the adjusting screw clockwise. * If the front frame side image is shifted toward the paper's leading edge, then turn the adjusting screw counterclockwise. It changes approx. 0.5mm by 90 degrees rotation. Repeat steps 2 to 4 until an acceptable result is obtained.

ADJ 4 Adjusting DSPF parallelism

If the above requirement is not met, do step 4. 4)

Turn the height adjusting screw on the left side of the DSPF rear frame to adjust the fore/aft levelness between the DSPF frames.

4-A Adjusting the DSPF parallelism This adjustment is needed in the following situations: * The DSPF section has been disassembled. * The DSPF unit has been replaced. 1)

Create two check sheets for DSPF levelness adjustment by cutting copy paper as illustrated below:

L R

OO

If the front frame side is higher (i.e. there is a gap in B) : turn the height adjusting screw L on the left side of the DSPF rear frame in the clockwise direction.

A4 size 2)

Insert each of the two check sheets in between the CIS guide boss and the glass for DSPF mode on each of the front and rear frame sides, and then close the DSPF unit.

If the rear frame side is higher (i.e. there is a gap in A) : turn the height adjusting screw L on the left side of the DSPF rear frame in the counterclockwise direction. Repeat steps 2 to 4 until an acceptable result is obtained. NOTE: If the above procedure will not allow an adjustment, turn the adjustment screw R on the rear frame of the DSPF to perform an adjustment.

MX-M700N ADJUSTMENTS 6 – 12

[Check Method 2]

4-B Adjust DSPF skews

Check that the squareness of the main scanning direction print line for the longitudinal direction of paper is within 0.5mm.

This adjustment is needed in the following situations: * The DSPF section has been disassembled. * The DSPF unit has been replaced. * The DSPF unit generates skewed scanned images. 1)

Create an adjustment chart by printing in duplex mode the selfprint pattern (grid pattern) specified in Simulation 64-1. Make sure that the print grid pattern is almost in parallel with the paper edges, and apply position marks 'A', 'B', 'C' and 'D' to the leading and trailing edges of the paper for both front and back sides of the paper.

A

A If the above requirement is met for the copied image of the paper's front side but not for the paper's back side, skip to step 4. If the above requirement is not met for the paper's front side, then do step 3.

B

2)

3)

Loosen the hinge screws and lower the two attachments.

4)

Open the DSPF and loosen the screw.

Copy the adjustment chart (created in step 1) to A3 (11" x 17") paper in duplex mode, and then check the image for skews (Set in the DSPF feed tray so that the mark on the adjustment chart is at the edge). Check with one of the following methods. [Check Method 1] (Front side) Make sure that the output satisfies the condition: |a-b|

A a

1mm

B b

(Back side) Make sure that the output satisfies the condition: |c-d|

C

D

c

d

1mm

MX-M700N ADJUSTMENTS 6 – 13

5)

Adjust by turning the DSPF skew adjusting screw on the right side of the DSPF rear frame. Remove the hexagon cap nut of the DSPF skew adjusting screw on the right side of the DSPF hinge and loosen the fixing nut, then adjust by turning the DSPF skew adjusting screw (hexagon screw).

ADJ 5 Adjusting the image focus The result of this adjustment will affect all image scan modes (copy, scan, and fax).

5-A Adjust the image focus in original table mode and DSPF front-face mode (CCD) This adjustment is needed in the following situations: * The CCD unit has been removed from the machine. * The CCD unit has been replaced. * Copied/scanned/faxed images are not correctly focused. 1)

Go through the modes specified in Simulation 48-1. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

2

Select other than 0 - 2, and press [START] key.

If a < b, then turn counterclockwise the DSPF skew adjusting screw (hexagon screw). (When the main scanning direction print line is shifted to the left)

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

If a > b, then turn clockwise the DSPF skew adjusting screw (hexagon screw). (When the main scanning direction print line is shifted to the right)

50

Select 1, and press [START] key.

Repeat steps 2 to 5 until an acceptable result is obtained.

Remove the DSPF front cover.

7)

Change the front frame side CIS fixing position (angle) to adjust the skew of the copied image of the paper's back side.

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

[If the copied image of the paper's back side is skewed beyond the acceptable level, do the following steps.] 6)

Press [SYSTEM SETTINGS] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 0, and press [START] key.

This adjustment should be done by loosening the CIS fixing screw on the DSPF front side and then moving the fixing plate in the left or right direction.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

100

2)

Set the adjustment item CCD (MAIN) to 50 (default).

3)

Place a scale on the original table as illustrated below.

81 2

51 2 A5

If c > d, then shift the CIS fixing plate to the left. (When the main scanning direction print line is shifted to the right)

51 2 A5

B5

Repeat steps 2 to 7 until an acceptable result is obtained.

A5 A4 81 2

B5 B4

11

A4 A3

MX-M700N ADJUSTMENTS 6 – 14

10 20 30 40 50 60 70 80 90 100110120130140

If c < d, then shift the CIS fixing plate to the right. (When the main scanning direction print line is shifted to the left)

B5

A4 A5

11 B5

13 A4

14

17 B4

A3

4)

Make a normal copy on A4 paper.

5)

Compare the copied image of the scale and the actual scale length in of length.

100mm scale (Original)

10

20

9)

90

100

Slide the CCD unit in the arrow direction (CCD sub-scanning direction) to change its mounted position.

110 B

0.8mm

Copy image (1mm (1%) shorter than the original)

A

10

20

90

100

110

If the copied image is not satisfactorily focused and larger than the original, slide the unit in direction B. If the copied image is not satisfactorily focused and smaller than the original, slide the unit in direction A.

If the copied image of the scale is of almost the same length as the actual scale but is not satisfactorily focused, do the following steps. 6)

Remove the table glass and dark box cover.

7)

To prevent the CCD unit optical axis from being deviated, mark the CCD unit base as illustrated below.

* After adjusting the CCD unit position, fix the CCD unit so that it is in parallel with the marker line added in step 7, referring to the graduations on the front and rear frames sides of the CCD unit base. Repeat steps 4 to 9 until the copied image of the scale is of almost the same size as the actual scale and the image is satisfactorily focused.

5-B Adjust the image focus in DSPF back-face mode (CIS) This adjustment is needed in the following situations: * The CIS unit has been removed. * The CIS unit has been replaced. * Copied/scanned/faxed images are not correctly focused. * The DSPF unit has been removed. * The DSPF unit has been replaced. 1)

Make a duplex copy in DSPF mode.

2)

Make sure that the copied image on the back side of the paper is satisfactorily focused. If the image is not satisfactorily focused, do the following steps.

8)

Loosen two fixing screws of the CCD unit.

3)

Remove the rear frame and front frame cabinet of the DSPF unit.

4)

Adjust the focus by turning the CIS focus adjusting screws on the front and rear frame sides, respectively.

* The screws cross-marked in the illustration must not be loosened. Loosening these screws could possibly change the CCD unit base optical axis. Once the optical axis has been changed, it cannot be corrected through on-site adjustments. Solving such a problem requires the replacement of the entire scanner unit.

MX-M700N ADJUSTMENTS 6 – 15

2)

Make a normal copy on A4 paper.

3)

Measure the lengths of the copied image of the scale and the actual scale.

100mm scale (Original)

10

20

90

100

110

0.8mm

Copy image (1mm (1%) shorter than the original)

Repeat the above adjustments until an acceptable result is obtained.

ADJ 6 Adjusting the image

4)

magnification

10

20

90

100

110

Determine the image magnification factor using the following formula: Image magnification factor (%) = Copy dimension/original dimension x 100

6-A Adjust the image magnification in the main scanning direction in original table mode (CCD)

Example: Compare the copy and original dimensions by aligning the scale's 10 mm position with the copied image's 10 mm position.

This adjustment is needed in the following situations:

Image magnification factor (%) = 99 / 100 x 100 = 99

* The CCD unit has been removed from the machine.

If the image magnification factor is within the spec (100r0.8%), no adjustment is required; otherwise, do the following steps.

* The CCD unit has been replaced. * Images are not correctly magnified in the main scanning direction. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced.

5)

Go through the modes specified in Simulation 48-1. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

2

* U2 trouble has occurred. 1)

Place a scale on the original table in parallel with the main scanning direction, as illustrated below.

81 2

51 2 A5

B5

A4 A5

11 B5

13 A4

14

17 B4

A3

Select other than 0 - 2, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

50

A5

B5

A5 A4

10 20 30 40 50 60 70 80 90 100110120130140

51 2

Select 1, and press [START] key.

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

81 2

B5 B4

11

A4 A3

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

Select 2, and press [START] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

MX-M700N ADJUSTMENTS 6 – 16

Press [START] key, or press [SYSTEM SETTINGS] key.

100

6)

Select the number that corresponds to the adjustment item CCD (MAIN) using the numeric keypad.

4)

Image magnification factor (%) = Copy dimension/original dimension x 100

This adjustment items is intended to adjust the image magnification in the main scanning direction in original table mode (CCD). 7)

Press the Start key.

8)

Adjust the image magnification factor by entering an appropriate value through the numeric keypad.

9)

Press the P or Start key.

Pressing the Start key starts copy operation as well as applying the adjustment value.

Determine the image magnification factor using the following formula:

Example: Compare the copy and original dimensions by aligning the scale's 10 mm position with the copied image's 10 mm position. Image magnification factor (%) = 99 / 100 x 100 = 99 If the image magnification factor is within the spec (100r0.8%), no adjustment is required; otherwise, do the following steps. 5)

Go through the modes specified in Simulation 48-1.

Repeat steps 2 to 9 until the image magnification factor is satisfactory. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

6-B Adjust the image magnification in the subscanning direction in original table mode (CCD)

2

This adjustment is needed in the following situations: * The CCD unit has been removed from the machine.

Select other than 0 - 2, and press [START] key.

* The CCD unit has been replaced. * Images are not correctly magnified in the sub-scanning direction.

Press [SYSTEM SETTINGS] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

* The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced.

50

* The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced.

Select 1, and press [START] key.

* U2 trouble has occurred. 1)

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

Place a scale on the original table as illustrated below. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

10 20 30 40 50 60 70 80 90 100110120130140

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

Select 2, and press [START] key.

2)

Make a normal copy on A4 paper.

3)

Measure the lengths of the copied image of the scale and the actual scale.

100mm scale (Original)

10

20

90

100

110

0.8mm

Copy image (1mm (1%) shorter than the original)

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

Press [START] key, or press [SYSTEM SETTINGS] key.

100

6)

Select the number that corresponds to the adjustment item CCD (SUB) using the numeric keypad. This adjustment item is intended to adjust the image magnification in the sub scanning direction in original table mode (CCD).

7)

Press the Start key.

8)

Adjust the image magnification factor by entering an appropriate value through the numeric keypad.

9)

Press the P or Start key.

Pressing the Start key starts copy operation as well as applying the adjustment value. Repeat steps 2 to 9 until the image magnification factor is satisfactory.

10

20

90

100

110

MX-M700N ADJUSTMENTS 6 – 17

5)

6-C Adjust the image magnification in the main scanning direction in DSPF front-face mode (CCD)

Go through the modes specified in Simulation 48-1. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

This adjustment is needed in the following situations: * The CCD unit has been removed from the machine.

2

* The CCD unit has been replaced. * Images are not correctly magnified in the main scanning direction.

Select other than 0 - 2, and press [START] key.

Press [SYSTEM SETTINGS] key.

* The MFP control PWB has been replaced. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

* The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced.

50

* The EEPROM on the scan control PWB has been replaced. * U2 trouble has occurred. 1)

On the DSPF original tray, place such an original as illustrated below.

Select 1, and press [START] key.

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

A4 size Select 0, and press [START] key.

10mm

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

10mm

1

Select 2, and press [START] key.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

2)

Make a normal copy on A4 paper.

3)

Measure the lengths of the copied image and the original image.

copy 50

100

150

200

6)

Press [START] key, or press [SYSTEM SETTINGS] key.

100

Using the mumeric keypad, select the number that corresponds to the mode for which to make adjustments. Select the adjustment item that is intended to adjust the image magnification in the main scanning direction in DSPF frontface mode (CCD). (SPF (MAIN))

original

10

Press [START] key, or press [SYSTEM SETTINGS] key.

7)

Press the Start key.

8)

Adjust the image magnification factor by entering an appropriate value through the numeric keypad.

9)

Press the P or Start key.

Pressing the Start key starts copy operation as well as applying the adjustment value.

250

Repeat the above adjustments until an acceptable result is obtained. 10

4)

50

100

150

200

250

Determine the image magnification factor using the following formula: Image magnification factor (%) = Copy dimension/original dimension x 100 Image magnification factor (%) = 99 / 100 x 100 = 99 If the image magnification factor is within the spec (100r0.8%), no adjustment is required; otherwise, do the following steps.

MX-M700N ADJUSTMENTS 6 – 18

5)

6-D Adjust the image magnification in the main scanning direction in DSPF back-face mode (CIS)

Go through the modes specified in Simulation 48-1. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

This adjustment is needed in the following situations: * The MFP control PWB has been replaced.

2

* The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced.

Select other than 0 - 2, and press [START] key.

* The EEPROM on the scan control PWB has been replaced.

Press [SYSTEM SETTINGS] key.

* U2 trouble has occurred. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

* Images are not correctly magnified in the main scanning direction. 1)

50

On the DSPF original tray, place such a duplex original as illustrated below.

Select 1, and press [START] key.

A4 size (both sides) 10mm

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

10mm SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

Select 2, and press [START] key.

2)

Make a normal duplex copy on A4 paper.

3)

Measure the lengths of the copied image (on the back side) and the original image.

original

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

6)

50

100

150

200

250

10

4)

50

100

150

200

100

Select the number that corresponds to the adjustment item CIS (MAIN) using the numeric keypad. This adjustment item is intended to adjust the image magnification in the main scanning direction in DSPF back-face mode (CIS). (CIS (MAIN))

copy 10

Press [START] key, or press [SYSTEM SETTINGS] key.

250

Determine the image magnification factor using the following formula:

7)

Press the Start key.

8)

Adjust the image magnification factor by entering an appropriate value through the numeric keypad.

9)

Press the P or Start key. Pressing the Start key starts copy operation as well as applying the adjustment value.

Repeat the above adjustments until an acceptable result is obtained.

Image magnification factor (%) = Copy dimension/original dimension x 100 Image magnification factor (%) = 99 / 100 x 100 = 99 If the image magnification factor is within the spec (100r0.8%), no adjustment is required; otherwise, do the following steps.

MX-M700N ADJUSTMENTS 6 – 19

5)

6-E Adjust the image magnification in the subscanning direction in DSPF mode

Go through the modes specified in Simulation 48-1. SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

This adjustment is needed in the following situations: * Images are not correctly magnified in the sub-scanning direction. * The MFP control PWB has been replaced.

2

* The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced.

Select other than 0 - 2, and press [START] key.

* The EEPROM on the scan control PWB has been replaced.

Press [SYSTEM SETTINGS] key.

* U2 trouble has occurred. 1)

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 4.CCD(SUB)

On the DSPF original tray, place such an original as illustrated below.

50

10mm Select 1, and press [START] key.

A4 size

Press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. NOW COPYING.

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

10mm SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

Select 2, and press [START] key.

2)

Make a normal copy on A4 paper.

3)

Measure the lengths of the copied image and the original image.

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

6)

100

10

Select the number that corresponds to the adjustment item SPF (SUB) using the numeric keypad.

50

This adjustment items is intended to adjust the image magnification in the sub-scanning direction in DSPF mode.

100

(SPF (SUB))

10 50

150

100

200

150

original

7)

Press the Start key.

8)

Adjust the image magnification factor by entering an appropriate value through the numeric keypad.

9)

Press the P or Start key. Pressing the Start key starts copy operation as well as applying the adjustment value. Repeat the above adjustments until an acceptable result is obtained.

copy

200

4)

Press [START] key, or press [SYSTEM SETTINGS] key.

* After adjusting the image magnification in the sub-scanning direction through Simulation 48-1, do the following steps if making a copy at a different magnification factor fails to produce a correctly scaled copy.

Determine the image magnification factor using the following formula: Image magnification factor (%) = Copy dimension/original dimension x 100

1)

Go through the modes specified in Simulation 48-5.

Image magnification factor (%) = 99 / 100 x 100 = 99 If the image magnification factor is within the spec (100r0.8%), no adjustment is required; otherwise, do the following steps.

SIMULATION 48-5 MOTOR SPEED ADJUSTMENT. SELECT 0-4, AND PRESS START. 0.MIR(220) 50 1.MIR(110) 50 2.SPF(360) 50 3.SPF(220) 50 4.SPF(110) 50

0

Select 0 - 5, and press [START] key.

MX-M700N ADJUSTMENTS 6 – 20

Press [START] key, or press [SYSTEM SETTINGS] key.

Item SIMULATION 48-5 SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 0.MIR(220)

0

50

2)

Using the numeric keypad, select the number that corresponds to the mode for which to make adjustments.

3)

Press the Start key.

4)

Enter the copy adjustment value using the numeric keypad. Make adjustments by changing the adjustment value for high revolution mode if the copy magnification is not correct for microcopies; or the adjustment value for low revolution mode if the copy magnification is not correct for blowbacks.

5)

Press the Start key. This applies the adjustment value.

ADJ 7 Adjusting the image off-center 7-A Adjust the print image off-center (print engine section) This adjustment is needed in the following situations: * The paper feed section has been disassembled. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced. * The scanner (reading) section has been disassembled. * The scanner (reading) unit has been replaced. * The LSU has been replaced. * U2 trouble has occurred. (Print image off-center adjustment) 1)

Go through the modes specified in Simulation 50-5. SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START (ADJUSTMENT DATA) LEAD EDGE: 2.RRCB 50 20.SIDE2 ADJ. 50 RESIST: 3.T1 50 4.T2 50 5.T3 50 6.T4 50 7.BPT 50 8.LCC 50 9.ADU 50 OFF CENTER: 10.T1 50 11.T2 50 12.T3 50 13.T4 50 14.BPT 50 15.LCC 50 16.ADU 50

2

(VOID SETTING) 17.LEAD_EDGE(DENA) 50 18.TRAIL_EDGE(DENB) 30

Select other than 0 - 1, and press [START] key.

19.FRONT/REAR 30

TRAY Paper feed tray SELECT selection 1 PRINT Print start (Default) START (Lead edge adjustment value) 2 RRCB Resist roller clutch ON timing adjustment value SIDE2-ADJ Offset (adjustment) of the RRCB setting during rear print. (Resist adjustment value) 3 TRAY1 Tray 1 adjustment 4 TRAY2 Tray 2 adjustment 5 TRAY3 Tray 3 adjustment 6 TRAY4 Tray 4 adjustment 7 BPT Manual feed tray adjustment 8 LCC Side LCC adjustment 9 ADU Adjustment when paper is fed again from ADU (Off-center set value) Self print 10 TRAY 1 Tray 1 adjustment 11 TRAY 2 Tray 2 adjustment 12 TRAY 3 Tray 3 adjustment 13 TRAY 4 Tray 4 adjustment 14 BPT Manual feed tray adjustment 15 LCC Side LCC adjustment 16 ADU Adjustment when paper is fed again from ADU (Void set value) 7 LEAD_EDG Lead edge void set E(DENA) value 8 TRAIL_ED Rear edge void GE(DENB) adjustment value 9 FRONT/ Front/Rear void REAR adjustment value

Default –

–

–

0 – 99

50

1 – 99

0 – 99

50

– – – – –

– – – – –

–

–

–

–

0 – 99

35

2)

Enter the number that corresponds to the paper feed tray that needs adjustments. (Choose from numbers 10 to 16.)

3)

Press the Start key.

4)

Press the Start key. A self-print pattern image is printed. Check the off-center of the printed self-print pattern image. If so, no adjustment is required.

Press [SYSTEM SETTINGS] key.

SIMULATION 50-5 LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 2.RRCB

50

Measure the void area dimensions in the front and rear frame directions, and make sure that the difference between the two dimensions is within 0r1.5 mm.

Press [START] key. Select 1, and Press [SYSTEM SETTINGS] press [START] key. key, or terminate copying. SIMULATION 50-5 LEAD EDGE ADJUSTMENT. NOW PRINTING.

Select 0, and press [START] key.

Setting range 1–6

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

MX-M700N ADJUSTMENTS 6 – 21

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

2

(ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50

Select other than 0 - 2, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.PLATEN

50

Select 1, and Press [START] key. press [START] Press [SYSTEM SETTINGS] key, key.1 or terminate copying. SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

1

If the above requirement is not met, do the following steps. 5)

6)

Using the numeric keypad, change the adjustment value in steps of 0.1 mm. A larger setting shifts the printed image toward the front side.

Select 2, and press [START] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

Press the P or Start key. Pressing the Start key starts print operation as well as applying the adjustment value. Check the off-center of the printed self-print pattern image.

Repeat steps 5 to 6 until an acceptable result is obtained.

7-B Adjust the scanned image off-center in original table mode (scan section) This adjustment is needed in the following situations: * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced. * The scanner (reading) section has been disassembled. * The scanner (reading) unit has been replaced. * U2 trouble has occurred. (Adjustment mode selection) 1)

Go through the modes specified in Simulation 50-12.

Press [START] key, or press [SYSTEM SETTINGS] key.

100

Increasing the adjustment value by 0.1 mm/step causes position of the printed image toward the front side. Item 0

TRAY Paper feed tray selection SELECT 1 COPY Copy START (Default) START 2 MAGNIFICA Print magnification ratio TION (Off-center adjustment value) 3 PLATEN OC mode adjustment 4 SPF SIDE1 SPF front surface adjustment 5 SPF SIDE2 SPF back surface adjustment

Setting range 1–5

Default –

–

–

25 – 400%

100

0 – 99

50

2)

Using the numeric keypad, select the adjustment item PLATEN, which is intended to adjust the off-center in original table mode.

3)

Press the Start key.

MX-M700N ADJUSTMENTS 6 – 22

(Scan off-center adjustment) 1)

Place an original on the original table.

2)

Press the Start key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

2

Check the off-center of the printed image. If the off-center is 0r4.0 mm, no adjustment is required.

original

(ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50

copy

Select other than 0 - 2, and press [START] key.

a

Press [SYSTEM SETTINGS] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.PLATEN

50

b

Select 1, and press [START] key.1

Press [START] key. Press [SYSTEM SETTINGS] key, or terminate copying.

If the above requirement is not met, do the following steps. 3)

Using the numeric keypad, change the adjustment value in steps of 0.1 mm to adjust the scan image off-center. A larger setting shifts the printed image toward the front side.

4)

Press the P or Start key. Pressing the Start key starts copy operation as well as applying the adjustment value.

5)

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.

Select 0, and press [START] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

Check the off-center of the printed image. Repeat the above adjustments until an acceptable result is obtained.

1

7-C Adjust the scanned image off-center in DSPF front-face mode (scan section) This adjustment is needed in the following situations: * The MFP control PWB has been replaced.

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

* The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

* The EEPROM on the scan control PWB has been replaced. * The scanner (reading) section has been disassembled. * The scanner (reading) unit has been replaced.

Increasing the adjustment value by 0.1 mm/step causes position of the printed image toward the front side.

* U2 trouble has occurred. * The DSPF section has been disassembled. * The DSPF unit has been replaced.

Item

(Adjustment mode selection) 1)

100

Go through the modes specified in Simulation 50-12.

0

TRAY Paper feed tray selection SELECT 1 COPY Copy START (Default) START 2 MAGNIFI Print magnification ratio CATION (Off-center adjustment value) 3 PLATEN OC mode adjustment 4 SPF SIDE1 SPF front surface adjustment 5 SPF SIDE2 SPF back surface adjustment

Setting range 1–5

Default –

–

–

25 – 400%

100

0 – 99

50

2)

Using the numeric keypad, select the adjustment item DSPF SIDE1, which is intended to adjust the off-center in DSPF front-face mode.

3)

Press the Start key.

MX-M700N ADJUSTMENTS 6 – 23

(Scan off-center adjustment)

(Adjustment mode selection)

1)

Place an original on the DSPF original tray.

1)

2)

Press the Start key. Check the off-center of the printed image. If the off-center is 0r2.5 mm, no adjustment is required.

original

Go through the modes specified in Simulation 50-12. SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

copy

2

(ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50

a

Select other than 0 - 2, and press [START] key.

b

Press [SYSTEM SETTINGS] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.PLATEN

50

Select 1, and Press [START] key. press [START] Press [SYSTEM SETTINGS] key, key.1 or terminate copying. SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.

Select 0, and press [START] key.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

If the above requirement is not met, do the following steps. 3)

Using the numeric keypad, change the adjustment value in steps of 0.1 mm to adjust the scan image off-center. A larger setting shifts the printed image toward the rear side.

4)

Press the P or Start key. Pressing the Start key starts copy operation as well as applying the adjustment value.

5)

Check the off-center of the printed image.

Press [START] key, or press [SYSTEM SETTINGS] key.

1

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

Repeat the above adjustments until an acceptable result is obtained. SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

7-D Adjust the scanned image off-center in DSPF back-face mode (scan section) This adjustment is needed in the following situations: * The MFP control PWB has been replaced.

100

Increasing the adjustment value by 0.1 mm/step causes position of the printed image toward the front side.

* The EEPROM on the MFP control PWB has been replaced. * The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced. * The scanner (reading) section has been disassembled. * The scanner (reading) unit has been replaced. * U2 trouble has occurred. * The DSPF section has been disassembled. * The DSPF unit has been replaced.

Item 0

TRAY Paper feed tray selection SELECT 1 COPY Copy START (Default) START 2 MAGNIFI Print magnification ratio CATION (Off-center adjustment value) 3 PLATEN OC mode adjustment 4 SPF SIDE1 SPF front surface adjustment 5 SPF SIDE2 SPF back surface adjustment

Setting range 1–5

Default –

–

–

25 – 400%

100

0 – 99

50

2)

Using the numeric keypad, select the adjustment item DSPF SIDE2, which is intended to adjust the off-center in DSPF back-face mode.

3)

Press the Start key.

MX-M700N ADJUSTMENTS 6 – 24

(Scan off-center adjustment) 1)

Place an original on the DSPF original tray.

2)

Press the Start key.

Papar lead edge

Papar tail edge

Since the front side and back side images are copied onto separate sheets, check the off-center of the back side image.

No Image

If the off-center is 0r2.7 mm, no adjustment is required.

original

Void (RV)

copy 10

a

20

LIL = 1.5 mm LV = 3.5 mm TV = 3.5 mm FV+RV= 7.0 mm

Image loss (LIL)

b

No Image Void (TV)

No Image No Image Void (FV)

Void (LV)

1)

Go through the modes specified in Simulation 50-1. SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.RRCA 50 4.RRCB 50 10.SIDE2 ADJ. 50 (IMAGE LOSS SETTING) 5.LEAD 15 6.SIDE 20 (VOID SETTING) 7.LEAD_EDGE(DENA) 50 8.TRAIL_EDGE(DENB) 30 9.FRONT/REAR 30

2

If the above requirement is not met, do the following steps. 3)

4)

Using the numeric keypad, change the adjustment value in steps of 0.1 mm to adjust the scan image off-center. A larger setting shifts the printed image toward the rear side.

Select other than 0 - 2, and press [START] key.

SIMULATION 50-1 LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 3.RRCA

Press the P or Start key. Pressing the Start key starts copy operation as well as applying the adjustment value.

5)

Press [SYSTEM SETTINGS] key.

50

Check the off-center of the printed image.

Select 1, and Press [START] key. Press [SYSTEM SETTING] key, press [START] key.

Repeat the above adjustments until an acceptable result is obtained.

or terminate copying.

SIMULATION 50-1 LEAD EDGE ADJUSTMENT. NOW COPYING.

ADJ 8 Adjusting the image position, image loss, and void area

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 0, and press [START] key.

SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

8-A Adjust copied image loss/void area in original table mode This adjustment is needed in the following situations:

1

* The paper feed section has been disassembled. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced.

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

* The scan control PWB has been replaced. * The EEPROM on the scan control PWB has been replaced.

SIMULATION 50-1 LEAD EDGE ADJUSTMENT. (MAGNIFICATION) INPUT 25-400(%)

* The scanner (reading) section has been disassembled. * The scanner (reading) unit has been replaced.

100

* The LSU has been replaced. * U2 trouble has occurred. Item 0 1 2

Content

TRAY SELECT Paper feed tray selection COPY START Copy START (Default) MAGNIFICATI Print magnification ratio ON (Lead edge adjustment value) 3 RRCA Document scan start position adjustment value 4 RRCB Resist roller clutch ON timing adjustment value

MX-M700N ADJUSTMENTS 6 – 25

Setting range 1–6 – 25 – 400% 0 – 99

Default – – –

50

Item

Content

SIDE2-ADJ

Offset (adjustment) of the RRCB setting during rear print.

Setting range 1 – 99

(Image loss set value) 5 LEAD LEAD Lead edge image loss set value 6 SIDE Side image loss set (Void set value) 7 LEAD_EDGE Lead edge void set value (DENA) 8 TRAIL_EDGE Rear edge void adjustment (DENB) value 9 FRONT/REAR Front/Rear void adjustment value

0 – 99

(Trailing edge void area adjustment) Default

1)

50

Make a copy at 100% magnification by entering "100" into the (MAGNIFICATION) field and then pressing the Start key, and check the trailing edge void area. (Standard setting) Trailing edge void area: 3.5 mm

15

Papar tail edge 20 0 – 99

35

TV

= 3.5 mm

Void (TV)

(Leading edge image loss/void area adjustment) 1)

Set the adjustment values for leading edge image loss and leading edge void as follows: (Standard setting) Leading edge image loss: 1.5 mm (LEAD:15)

No Image

Leading edge void: 3.5mm (DENA:35) * Set the adjustment value for (LEAD) to 15 by entering "15" into the (LEAD) adjustment value field and then pressing the P key.

If the trailing edge void area is not at an acceptable level, do the following steps. 2)

* Set the adjustment value for (DENA) to 35 by entering "35" into the (DENA) adjustment value field and then pressing the P key. 2)

Make a copy at 100% magnification by entering "100" into the (MAGNIFICATION) field and then pressing the Start key, and check the leading edge void area and image loss.

Repeat the process of changing the (TRAIL EDGE) adjustment value and then pressing the Start key until attaining an acceptable level. Repeat the above adjustments until acceptable results are obtained.

(Front/rear frame direction image loss adjustment) 1)

Set the (SIDE) adjustment value to 20 by entering "20" into the (SIDE) adjustment value field and then pressing the P key. Note that changing this adjustment value shifts the image position in the front/rear frame direction.

(Front/rear frame direction void area) 1)

Papar lead edge

10

20

Image area

Make a copy at 100% magnification by entering "100" into the (MAGNIFICATION) field and then pressing the Start key, and check the front/rear frame direction void area. (Standard settings) Front frame side void area = 3.5 mm, rear frame side void area = 3.5 mm, sum of front/rear frame direction void area = 7.0 mm.

Image loss (LIL) No Image

Void (LV)

LIL = 1.5 mm LV = 3.5 mm

No Image

If the leading edge image loss and void area are not at acceptable levels, do the following steps.

Void (RV)

* If the leading edge void area is not 3.5 mm: Repeat the process of changing the (RRCB) adjustment value and then pressing the Start key until attaining an acceptable level. FV+RV= 7.0 mm

(The change according to the one step of the adjustment value is 0.1mm.) * If the leading edge image loss is not 1.5mm:

No Image Void (FV)

Repeat the process of changing the (RRCA) adjustment value, in steps of 0.1 mm, and then pressing the Start key until attaining an acceptable level. If the front/rear frame direction void area is not at an acceptable level, do the following steps.

(The adjustment value should be changed in steps of 0.2mm.) Repeat the above adjustments until acceptable results are obtained.

2)

Repeat the process of changing the (FRONT/REAR) adjustment value and then pressing the Start key until attaining an acceptable level.

Repeat the above adjustments until acceptable results are obtained. NOTE: If the front and rear frame side void areas are not equal, adjust the image off-center position using Simulation 50-5. MX-M700N ADJUSTMENTS 6 – 26

8-B Adjust the original scan start position (adjust the scanner read position in DSPFmode front face scan)

8-C Adjust the copied image loss/void area in DSPF mode This adjustment is needed in the following situations:

This adjustment is needed in the following situations:

* The MFP control PWB has been replaced.

* The MFP control PWB has been replaced.

* The EEPROM on the MFP control PWB has been replaced.

* The EEPROM on the MFP control PWB has been replaced.

* The scan control PWB has been replaced.

* The scan control PWB has been replaced.

* The EEPROM on the scan control PWB has been replaced.

* The EEPROM on the scan control PWB has been replaced.

* The scanner (reading) section has been disassembled.

* The scanner (reading) section has been disassembled.

* The scanner (reading) unit has been replaced.

* The scanner (reading) unit has been replaced.

* U2 trouble has occurred.

* U2 trouble has occurred.

* The DSPF section has been disassembled.

* The DSPF section has been disassembled.

* The DSPF unit has been replaced.

* The DSPF unit has been replaced.

Papar lead edge

Papar tail edge

This adjustment is intended to adjust the scanner read position in DSPF mode front face scan. An incorrect adjustment would deviate the scanner stop position from the required position, thus possibly causing a shadow of the original table to appear at the leading edge of an image generated by DSPF (front-face) mode scan. 1)

No Image Void (RV)

Make a copy in DSPF (front-face) mode, and make sure that the printed image at the leading edge of the copied image is free from shadows.

10

20

LIL = 1.5 mm LV = 3.5 mm TV = 3.5 mm FV+RV= 7.0 mm

Image loss (LIL)

No Image Void (TV)

No Image

Papar lead edge

No Image Void (FV)

Void (LV)

Image area 1)

Shadow image of DSPF

If the printed image at the leading edge of the copied image contains a shadow of the original table, then do the following steps. 2)

Go through the modes specified in Simulation 53-8. SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT. PRESS START. 2.MANUAL

Go through the modes specified in Simulation 50-6. SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

2

(ADJUSTMENT DATA)3.SIDE1 50 4.SIDE2 50 (IMAGE LOSS SETTING) SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0 SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0

Select other than 0 - 2, and press [START] key.

Press [SYSTEM SETTING] key.

SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). INPUT VALUE 0-99, AND PRESS START. 3.SIDE1

25

50

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 1, and Press [START] key. press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). NOW COPYING.

SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT. INPUT VALUE 1-70, AND PRESS START. 2.MANUAL

25

3)

Enter the adjustment value and press the Start key.

Repeat the above adjustments until an acceptable result is obtained.

Select 0, and press [START] key.

Press [START] key or press [SYSTEM SETTINGS] key.

SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). SELECT 1-16, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE+10: DUPLEX MODE)

Select 2, and press [START] key.

MX-M700N ADJUSTMENTS 6 – 27

1

Press [START] key, or press [SYSTEM SETTINGS] key.

3) SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). (MAGNIFICATION) INPUT 25-200(%)

Item 0

TRAY Paper feed tray selection SELECT 1 COPY Copy START (Default) START 2 MAGNIFI Print magnification ratio CATION (Lead edge adjustment value) 3 SIDE1 Front surface document scan start position adjustment value 4 SIDE2 Back surface document scan start position adjustment value (Image loss set value: SIDE 1) 5 LEAD Front surface lead edge _EDGE image loss set value 6 FRONT Front surface side edge _REAR image loss set value 7 TRAIL Front surface rear edge _EDGE image loss set value (Image loss set value: SIDE 2) 8 LEAD Back surface lead edge _EDGE image loss set value 9 FRONT Back surface side edge /REAR image loss set value 10 TRAIL Back surface rear edge _EDGE image loss set value

100 Setting range 1–6

SIDE1: Adjustment value for the position at which to read the leading edge of the original in DSPF front side mode. SIDE2: Adjustment value for the position at which to read the leading edge of the original in DSPF back side mode.

Default

(The change according to the one step of the adjustment value is 0.1mm.)

—

—

—

25 – 200%

—

0 – 99

50

(The timing in which to start reading the image should be determined based on the timing in which detector SPPD4 detects the leading edge of the original.) Repeat steps 2 to 3 until an acceptable result is obtained. (Trailing edge image loss adjustment) 1)

0 – 99

Repeat the process of changing the (SIDE1 & SIDE2) adjustment values and then pressing the Start key until attaining an acceptable level.

Select duplex mode from paper selection mode as described in Simulation 50-6, enter "100" into the (MAGNIFICATION) field, and then press the Start key to make a duplex copy at 100% magnification in DSPF mode, and make sure that the trailing edge image loss is 1.5 mm for both front and back sides.

15

Papar trail edge 20 0 – 20

0

0 – 99

15

TIL = 1.5 mm TV = 3.5 mm

Image area 20 0 – 20

Image loss (TIL)

0

Void (TV)

(Leading edge image loss adjustment) 1)

Set the adjustment values for leading edge image loss for the front and back sides as follows: (Standard setting)

No Image

If an acceptable result is not obtained, do the following steps. 2)

5 LEAD_EDGE: 15 8 LEAD_EDGE: 15 * Set the adjustment value for "5 LEAD_EDGE" and "8 LEAD_EDGE" to 15 by entering "15" into the (LEAD EDGE) adjustment value field and then pressing the P key. 2)

In DSPF mode, make a duplex copy at 100% magnification, and make sure that the leading edge image loss is 1.5 mm for both the front and back sides. (Select duplex mode from the paper selection mode as described in Simulation 50-6). (Enter "100" into the (MAGNIFICATION) field, and then press the start key).

Repeat the above adjustments until an acceptable result is obtained. (Front/rear frame direction image loss adjustment) Set the (FRONT/REAR) adjustment value to 20 by entering "20" into the (FRONT/REAR) adjustment value field and then pressing. Note that changing this adjustment value shifts the image position in the front/rear frame direction.

8-D Adjust the image loss in scanner mode 1)

Papar lead edge

Repeat the process of changing the (TRAIL EDGE) adjustment value and then pressing the Start key until attaining an acceptable level.

Go through the modes specified in Simulation 50-27. SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND PRESS START. [FAX] 1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0 4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0 7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0 [SCN] 10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0 13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0 16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0

TIL = 1.5 mm TV = 3.5 mm

1

Image area Image loss (TIL) Void (TV)

No Image

If an acceptable result is not obtained, do the following steps.

Press [START] key.

MX-M700N ADJUSTMENTS 6 – 28

Press [SYSTEM SETTINGS] key.

Setting range

Default

OC lead edge OC side OC rear edge SPF lead edge SPF side SPF rear edge CIS lead edge CIS side CIS rear edge

0 – 10 (Unit 1mm)

3 (3mm)

OC lead edge OC side OC rear edge SPF lead edge SPF side SPF rear edge CIS lead edge CIS side CIS rear edge

0 – 10 (Unit 1mm)

0 (0mm)

Item SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND PRESS START. 1.OC(LEAD_EDGE)

0

Setting range

Default

OC lead edge OC side OC rear edge SPF lead edge SPF side SPF rear edge CIS lead edge CIS side CIS rear edge

0 – 10 (Unit 1mm)

3 (3mm)

OC lead edge OC side OC rear edge SPF lead edge SPF side SPF rear edge CIS lead edge CIS side CIS rear edge

0 – 10 (Unit 1mm)

Item FAX send 1 OC (LEAD_EDGE) 2 OC (FRONT/REAR) 3 OC (TRAIL_EDGE) 4 SPF (LEAD_EDGE) 5 SPF (FRONT/REAR) 6 SPF (TRAIL_EDGE) 7 CIS (LEAD_EDGE) 8 CIS (FRONT/REAR) 9 CIS (TRAIL_EDGE) Scanner mode 10 OC (LEAD_EDGE) 11 OC (FRONT/REAR) 12 OC (TRAIL_EDGE) 13 SPF (LEAD_EDGE) 14 SPF (FRONT/REAR) 15 SPF (TRAIL_EDGE) 16 CIS (LEAD_EDGE) 17 CIS (FRONT/REAR) 18 CIS (TRAIL_EDGE)

0 (0mm)

FAX send 1 OC (LEAD_EDGE) 2 OC (FRONT/REAR) 3 OC (TRAIL_EDGE) 4 SPF (LEAD_EDGE) 5 SPF (FRONT/REAR) 6 SPF (TRAIL_EDGE) 7 CIS (LEAD_EDGE) 8 CIS (FRONT/REAR) 9 CIS (TRAIL_EDGE) Scanner mode 10 OC (LEAD_EDGE) 11 OC (FRONT/REAR) 12 OC (TRAIL_EDGE) 13 SPF (LEAD_EDGE) 14 SPF (FRONT/REAR) 15 SPF (TRAIL_EDGE) 16 CIS (LEAD_EDGE) 17 CIS (FRONT/REAR) 18 CIS (TRAIL_EDGE)

2)

Enter the number that corresponds to the fax adjustment item using the numeric keypad.

3)

Press the Start key.

4)

Enter the adjustment value using the numeric keypad.

5)

Press the Start key.

(The adjustment value should be changed in steps of 1.0mm.)

2)

Using the numeric keypad, enter the number that corresponds to the scanner mode adjustment item.

3)

Press the Start key.

4)

Enter the adjustment value using the numeric keypad.

5)

Press the Start key (The adjustment value should be changed in steps of 1.0mm.)

Scanned images must be visually checked for image loss. NOTE: Make adjustments in the same manner as in ADJ 8A and ADJ 8C.

ADJ 9 Adjusting the copied image

Scanned images must be visually checked for image loss. NOTE: Make adjustments in the same manner as in ADJ 8A and ADJ 8C.

quality This adjustment is needed in the following situations: * The CCD unit has been replaced.

8-E Adjust the image loss for images sent in fax mode 1)

Go through the modes specified in Simulation 50-27.

* U2 trouble has occurred. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced. * The scanner control PWB has been replaced.

SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND PRESS START. [FAX] 1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0 4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0 7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0 [SCN] 10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0 13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0 16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0

1

Press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND PRESS START. 1.OC(LEAD_EDGE)

0

* The EEPROM on the scanner control PWB has been replaced. * One or more parts of the scanner (reading) section have been replaced. * One or more consumables (OPC drum, developer, transfer belt) have been replaced. (Copy mode image quality adjustment items)

Image mode Auto mode Text mode Text/photo mode Photo mode

Binary mode Binary mode Binary mode Binary mode

Adjustment Item List Copied image gamma adjustment (copier mode) Adjust the copied image sharpness

MX-M700N ADJUSTMENTS 6 – 29

Simulation for adjustment All-mode Individualmode adjustment adjustment 46–2 46–9 46–10 46–11 Simulation for adjustment 46–18 46–31

(Copied image reference density)

2)

Go through the modes specified in Simulation 46-2.

Original

2

3

4

5

1

GRAY CHART

R

1

SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. AE 3.0 50 4. CH 3.0 50 5. MIX 3.0 50 6. PHOTO 3.0 50

6

7

8

9

10

W

Select other then 0 - 2, and press Press [SYSTEM SETTINGS] [START] key. key.

Lot No. 01A

SIMULATION 46-2 EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START. 3. AE 3.0

Copy

50

1

2

3

4

5

Select 1, Press [START] key. and press Press [SYSTEM SETTINGS] [START] key. key, or terminate copying.

GRAY CHART

R

6

7

8

9

10

W

SIMULATION 46-2 EXP. LEVEL SETUP (2). NOW COPYING. Lot No. 01A

If the copied test chart (UKOG-0162FCZZ) image includes a background copy of patch 3 rather than patch 2, adjust all-copy mode to the image density level specified above.

Select 0, and press [START] key.

SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 1-6, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT 6. LCC

(Copied image gamma, copied image sharpness) Normally, default settings should be applied to 'copied image gamma' and 'copied image sharpness', but images should be adjusted according to requests, if any.

9-A Adjust the binary mode copy density for all modes at once 1)

Press [START] key, or press [SYSTEM SETTINGS] key.

1

Select 2, and press [START] key.

Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START. (EXP. LEVEL SELECT) 3. AE 3.0 4. CH 3.0 5. MIX 3.0 6. PHOTO 3.0

1

Item 0 1 2 3 4 5 6

00

3)

TRAY SELECT COPY START EXP LEVEL AE 3.0 CH 3.0 MIX 3.0 PHOTO 3.0

Paper feed tray selection Copy START (Default) Exposure level selection AE mode Text mode 3.0 Text/Photo mode 3.0 Photo mode 3.0

Setting range

Default

0 – 99

50

Using the numeric keypad, select the number that corresponds to the copy mode for which to make adjustments. (Choose from numbers 3 to 6.)

4)

Press the Start key.

5)

Press the Start key (A copy is created.) Check the density of the copied image. If the copied image density is not at an acceptable level, do the following steps.

6)

Adjust the copy density by entering an appropriate value through the numeric keypad.

7)

Press the P or Start key. This applies the adjustment value.

A larger value provides higher density. Pressing the Start key starts copy operation as well as applying the adjustment value. 8)

Check the copied image density.

Repeat steps 6 to 8 until an acceptable copied image density is obtained.

MX-M700N ADJUSTMENTS 6 – 30

NOTE: Adjusting the copied image density through this simulation changes the copied image density settings for all copy modes to the copied image density level applied by carrying out this simulation. Also, the copied image density gradient is automatically adjusted to the specified level. The copied image density settings for individual copy modes adjusted through Simulations 46-9, -10, and -11 are changed to the copied image density level applied by this simulation.

9-B Adjust the copy density in text binary mode 9-C Adjust the copy density in text/photo binary mode

(SIM 46-9) (Text mode) Item 0 1 2 3 4 5 6 7 8 9 10 11

1)

Set the test chart (UKOG-0162FCZZ) on the original table.

2)

Go through the simulation modes that correspond to the copy modes for which to adjust the copy density (i.e., the modes specified in Simulations 46-9, -10, or -11). SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50

1

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

Item 0 1 2 3 4 5 6 7 8 9 10 11

TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

Press [SYSTEM SETTINGS] key.

SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS START. 3. 1.0

50

Select 1, Press [START] key. and press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). NOW COPYING.

Select 0, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 1-6, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT 6. LCC

0 1 2 3 4 5 6 7 8 9 10 11

1

Setting range

Default

0 – 99

50

Setting range

Default

TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

0 – 99

50

Using the numeric keypad, select the number that corresponds to the copy density adjustment level. (Choose from numbers 3 to 11.)

4)

Press the Start key.

5)

Press the Start key. (A copy is created.) If the copied image density is not at an acceptable level, do the following steps.

6)

Adjust the copy density by entering an appropriate value through the numeric keypad.

7)

Press the P or Start key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START. (EXP. LEVEL SELECT) 3. 1.0 4. 1.5 5. 2.0 6. 2.5 7. 3.0 8. 3.5 9. 4.0 10. 4.5 11. 5.0

50

3)

1

Select 2, and press [START] key.

0 – 99

(SIM 46-11) (Photo mode) Item

Select other than 0 - 2, and press [START] key.

Default

(SIM 46-10) (Text/photo mode)

9-D Adjust the copy density in photo binary mode This adjustment is intended to customize the copied image density settings. The copy density setting for each copy density adjustment level (1 to 5) in manual copy mode can be adjusted to a custom density level.

TRAY SELECT COPY START EXP LEVEL 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

Setting range

A larger value provides higher density. This applies the adjustment value. Pressing the Start key starts copy operation as well as applying the adjustment value. 8)

Check the copied image density.

Repeat steps 5 to 8 until an acceptable copied image density is obtained.

MX-M700N ADJUSTMENTS 6 – 31

9-E Adjust the copied image gamma in copy mode 1)

Set the original on the original table.

2)

Go through the modes specified in Simulation 46-18.

6)

Press the P or Start key. Pressing the Start key starts copy (print) operation as well as applying the adjustment value.

7)

Check the copied image gamma (copy density levels for low and high density areas) (contrast).

Repeat steps 5 to 7 until an acceptable copied image is obtained.

SIMULATION 46-18 GAMMA SETUP(COPIER). SELECT 1-14, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.OC_AE 64 4.OC_CHARA 5.OC_MIX 64 6.OC_PHOTO 64 7.SPF_AE 64 8.SPF_CHARA 64 9.SPF_MIX 64 10.SPF_PHOTO 64 11.CIS_AE 64 12.CIS_CHARA 64 13.CIS_MIX 64 14.CIS_PHOTO 64

9-F

Adjust the copied image sharpness

1)

Set the original on the original table.

2)

Go through the modes specified in Simulation 46-31. SIMULATION 46-31 SHARPNESS LEVEL SETUP. SELECT 1-12, AND PRESS START. 1.OC_AE 3 2.OC_CHARA 3 3.OC_MIX 3 4.OC_PHOTO 3 5.SPF_AE 3 6.SPF_CHARA 3 7.SPF_MIX 3 8.SPF_PHOTO 3 9.SPF2_AE 3 10.SPF2_CHARA 3 11.SPF2_MIX 3 12.SPF2_PHOTO 3 13.CIS_AE 3 14.CIS_CHARA 3 15.CIS_MIX 3 16.CIS_PHOTO 3

Select other than 0 - 2, and press [START] key. Press [SYSTEM SETTINGS] key. SIMULATION 46-18 GAMMA SETUP. INPUT VALUE 0-127, AND PRESS START. 3.OC_AE

64

Press [START] key.

Select 1, Press [START] key. and press Press [SYSTEM SETTINGS] [START] key. key, or terminate copying.

Press [SYSTEM SETTINGS] key.

SIMULATION 46-31 SHARPNESS LEVEL SETUP. INPUT VALUE 0-3, AND PRESS START. 1.OC_AE

SIMULATION 46-18 GAMMA SETUP. NOW PRINTING.

䋳

Select 0, and press [START] key.

Item SIMULATION 46-18 GAMMA SETUP. SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

Select 2, and press [START] key.

Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

TRAY SELECT PRINT START EXP LEVEL OC_AE OC_CHARA OC_MIX OC_PHOTO SPF_AE SPF_CHARA SPF_MIX SPF_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO

Paper feed tray selection Print start (Default) Exposure level selection AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF) Text mode (SPF) Text/Photo mode (SPF) Photo mode (SPF) AE mode (CIS) Text mode (CIS) Text/Photo mode (CIS) Photo mode (CIS)

1

Setting range

OC_AE OC_CHARA OC_MIX OC_PHOTO SPF1_AE SPF1_CHARA SPF1_MIX

8 9 10 11

SPF1_PHOTO SPF2_AE SPF2_CHARA SPF2_MIX

12 13 14 15 16

SPF2_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO

1

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-18 GAMMA SETUP. SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)

1 2 3 4 5 6 7

Default

AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF1) Text mode (SPF1) Text/Photo mode (SPF1) Photo mode (SPF1) AE mode (SPF2) Text mode (SPF2) Text/Photo mode (SPF2) Photo mode (SPF2) AE mode (CIS) Text mode (CIS) Text/Photo mode (CIS) Photo mode (CIS)

Setting range 1–5

Default 3

3)

Using the numeric keypad, select the number that corresponds to the copy mode for which to make adjustments.

4)

Press the Start key.

5)

Adjust the sharpness by entering an appropriate value through the numeric keypad.

6)

Press the P or Start key.

(Choose from numbers 1 to 16.) 0 – 127

96 64

A larger value provides higher sharpness. 96 64

Pressing the Start key starts copy (print) operation as well as applying the adjustment value. 7)

96 64

3)

Using the numeric keypad, select the number that corresponds to the copy mode for which to make adjustments. (Choose from numbers 3 to 14.)

4)

Press the Start key.

5)

Enter the gamma adjustment value using the numeric keypad. A larger value provides larger gamma gradient and higher image contrast.

Check the copied image sharpness.

Repeat steps 5 to 7 until an acceptable copied image is obtained.

MX-M700N ADJUSTMENTS 6 – 32

ADJ 10 Adjusting the print quality in fax mode

10-A Adjust the fax mode print density for all modes at once 1)

Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper.

This adjustment is needed in the following situations: * The CCD unit has been replaced. * U2 trouble has occurred. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced. * The scanner control PWB has been replaced. * The EEPROM on the scanner control PWB has been replaced. * One or more parts of the scanner (reading) section have been replaced. (Fax mode image density adjustment items)

Image mode

Adjust the fax mode print density in standard mode Adjust the fax mode print density in small-character mode

Adjust the fax mode print density in fine mode

Auto mode Manual Auto mode Manual

Auto mode Manual

Adjust the fax mode print density in super fine mode

Auto mode Manual

Adjust the fax mode print density in 600dpi mode

Auto mode Manual

Binary mode

Simulation for adjustment All-mode Individual adjustment mode adjustment 46-12 46-13

00

2) Binary mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode

Go through the modes specified in Simulation 46-12.

46-14 SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.FAX EXP.LEVEL 50

1

46-15

Select other than 0 - 1, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 2.FAX EXP.LEVEL

50

46-16

Select 1, Press [START] key. and press [START] key.

Press [SYSTEM SETTINGS] key, or terminate copying.

SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET). NOW PRINTING.

46-45

Select 0, and press [START] key.

(Fax mode density)

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

The print density settings should be normally left at defaults but should be adjusted according to requests, if any.

䋱

Item 0

TRAY SELECT

1 2

COPY START FAX EXP. LEVEL

Paper feed tray selection Copy START (Default) FAX mode print density

Setting range

Default

0 – 99

50

3)

Select the adjustment item (FAX EXP. LEVEL) using the numeric keypad.

4)

Press the Start key.

5)

Press the Start key. (A copy is created.) Check the print density. If the print density is not at an acceptable level, do the following steps.

6)

Enter the print adjustment value using the numeric keypad.

MX-M700N ADJUSTMENTS 6 – 33

7)

Press the P or Start key.

2)

Go through the simulation modes that correspond to the Fax modes for which to adjust the print density (i.e., the modes specified in Simulations 46-13, -14, -15, -16, or -45).

This applies the adjustment value. Pressing the Start key starts print operation as well as applying the adjustment value. 8)

Check the print density.

SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50

Repeat steps 5 to 8 until an acceptable print density is obtained. Adjusting the Fax print density through this simulation changes the print density settings for all Fax modes to the density level applied by carrying out this simulation.

1

The Fax mode print density settings for individual Fax modes adjusted through Simulations 46-13, -14, -15, -16 and -45 are changed to the print density level applied by this simulation.

Select other than 0 - 2, and press [START] key.

10-B Adjust the fax mode print density in standard mode 10-C Adjust the fax mode print density in smallcharacter mode 10-D Adjust the fax mode print density in fine mode

Press [SYSTEM SETTINGS] key.

SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND PRESS START. 4.1.0

50

Select 1, Press [START] key. Press [SYSTEM SETTINGS] and press key, or terminate copying. [START] key. SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING. 㩷

10-E Adjust the fax mode print density in super fine mode Select 0, and press [START] key.

10-F Adjust the fax mode print density in 600dpi mode

SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC (ABOVE +20:DSPF MODE)

This adjustment is intended to the print mode for each Fax mode individually. In manual mode, the print density setting for each print density adjustment level (1 to 5) can be adjusted to a custom density level. 1)

Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper.

Press [START] key, or press [SYSTEM SETTINGS] key.

1

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0

1

Item 00

0 1 2 3 4 5 6 7 8

TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0

MX-M700N ADJUSTMENTS 6 – 34

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5

Setting range

Default

0 – 99

50

[Binary mode] (Copied image reference density)

SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50

Original

1

Select other than 0 - 2, and press [START] key.

GRAY CHART

R

1

2

3

4

5

6

7

8

9

Press [SYSTEM SETTINGS] key.

10

W

Lot No. 01A

SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS START. 4.1.0

Copy

50

GRAY CHART

R

Select 1, Press [START] key. Press [SYSTEM SETTINGS] and press key, or terminate copying. [START] key.

1

2

3

4

5

6

7

8

9

SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). NOW PRINTING.

Select 0, and press [START] key.

W

Lot No. 01A

If the copied test chart (UKOG-0162FCZZ) image includes a background copy of patch 6 rather than patch 5, adjust allcopy mode to the image density level specified above.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 46-13 EXP.LEVEL SETUP FAX(FINE). SELECT 1-6, AND PRESS START. (FEED TRAY) 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

[Half-tone mode] (Copied image reference density)

1

Select 2, and press [START] key.

10

Original

Press [START] key, or press [SYSTEM SETTINGS] key.

GRAY CHART

R

1

SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START. (EXP.LEVEL SELECT) 3.AUTO 4.1.0 5.2.0 6.3.0 7.4.0 8.5.0 9.AUTO(H) 10.1.0(H) 11.2.0(H) 12.3.0(H) 13.4.0(H) 14.5.0(H)

2

3

4

5

6

7

8

9

10

W

Lot No. 01A

1

Copy GRAY CHART

R

Item 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

3)

TRAY SELECT PRINT START EXP LEVEL AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H)

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range

Default

0 – 99

50

1

2

7

8

9

10

W

6)

Adjust the copy density by entering an appropriate value through the numeric keypad.

7)

Press the P or Start key.

A larger value provides higher density. This applies the adjustment value. Pressing the Start key starts copy operation as well as applying the adjustment value. 8)

Check the printed image density. Repeat steps 6 to 8 until an acceptable image density is obtained.

For manual mode, select the number that corresponds to the print density level (1 to 5). (Choose from numbers (4 to 8) (1014)). Press the Start key. (A copy is created.)

6

If the print density is not at an acceptable level, do the following steps.

* Manual mode (print density adjustment level)

Press the Start key.

5

The copied test chart (UKOG-0162FCZZ) image includes a background copy of patch 2 rather than patch 1.

* Auto mode

5)

4

Lot No. 01A

Using the numeric keypad, select the number that corresponds to the adjustment item. Choose from numbers 3 to 8 (14).

4)

3

MX-M700N ADJUSTMENTS 6 – 35

2)

Go through the modes specified in Simulation 46-21.

ADJ 11 Adjusting the image quality in

SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), PRESS START. 0.SCANNER EXP.LEVEL 50

scan mode This adjustment is needed in the following situations:

0

* The CCD unit has been replaced. * U2 trouble has occurred. Press [START] key.

* The MFP control PWB has been replaced.

Press [START] key, or press [SYSTEM SETTINGS] key.

* The EEPROM on the MFP control PWB has been replaced. * The scanner control PWB has been replaced. * The EEPROM on the scanner control PWB has been replaced.

SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 0.SCANNER EXP.LEVEL

* One or more parts of the scanner (reading) section have been replaced.

50

(Scan mode image quality adjustment items)

Image mode

Scan mode image density adjustment/ individual setup (standard mode) Scan mode image density adjustment/ individual setup (small-character mode)

Auto mode Manual

Scan mode image density adjustment/ individual setup (fine mode)

Auto mode

Scan mode image density adjustment/ individual setup (super fine mode)

Auto mode Manual

Manual

Auto mode Manual

Binary mode

Simulation for adjustment All-mode Individual adjustment mode adjustment 46-21 46-22

Binary mode

Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode Binary mode Half tone mode

46-23

46-24

Item 0

SCANNER EXP. LEVEL

Scan mode image density adjustment

Setting range 0 – 99

Default 50

3)

Select the adjustment item SCANNER EXP. LEVEL using the numeric keypad.

4)

Press the Start key.

5)

Enter the image density adjustment value.

6)

Press the P or Start key.

NOTE: Adjusting the scanned image density through this simulation changes the image density settings for all scan modes to the image density level applied by carrying out this simulation. The scan-mode image density settings for individual scan modes adjusted through Simulations 46-22, -23, -24, -25, and -45 are changed to the image density level applied by this simulation. Scanned images must be visually checked to ensure the postadjustment image density.

46-25

11-B Scan mode image density adjustment/ individual setup (standard mode) 11-C Scan mode image density adjustment/ individual setup (small-character mode)

(Scan mode image quality) The image density settings should be normally left at defaults but should be adjusted according to requests, if any.

11-D Scan mode image density adjustment/ individual setup (fine mode)

11-A Adjust the scan mode image density for all modes at once

11-E Scan mode image density adjustment/ individual setup (super fine mode)

1)

This adjustment is intended to the image mode for each scan mode individually. In manual mode, the image density setting for each scanned image density adjustment level (1 to 5) can be adjusted to a custom density level.

Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper.

1)

Set the test chart (UKOG-0162FCZZ) on the original table so that it aligns with the front frame. Then put four or five pieces of A3 (11" x 17") paper.

00

00

MX-M700N ADJUSTMENTS 6 – 36

2)

Go through the simulation modes that correspond to the scan modes for which to adjust the scanned image density (i.e., the modes specified in Simulations 46-22, -23, -24, or -25).

11-F Adjust the image gamma in scanner mode 1)

Go through the modes specified in Simulation 46-27.

SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), PRESS START. 0.SCANNER EXP.LEVEL 50

SIMULATION 46-27 GAMMA SETUP(SCNNER), SELECT 1-9, AND PRESS START. 1.OC_Fine.HT 64 2.OC_SFine.HT 64 3.OC_UFine.HT 64 4.SPF_Fine.HT 64 5.SPF_SFine.HT 64 6.SPF_UFine.HT 64 7.CIS_Fine.HT 64 8.CIS_SFine.HT 64 9.CIS_UFine.HT 64

0 Press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

Item 1 2 3 4 5 6 7 8 9

SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), INPUT VALUE 0-99, AND PRESS START. 0.SCANNER EXP.LEVEL

50

Item 0

SCANNER EXP. LEVEL

Scan mode image density adjustment

Setting range 0 – 99

Default 50

SIMULATION 46-22 EXP.LEVEL SETUP SCANNER(NORMAL). SELECT 0-5, AND PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 50 3.3.0 50 4.4.0 50 5.5.0 50

OC_Fine.HT OC_SFine.HT OC_UFine.HT SPF_Fine.HT SPF_SFine.HT SPF_UFine.HT CIS_Fine.HT CIS_SFine.HT CIS_UFine.HT

Fine text (Half-tone) (OC) Super fine (Half-tone) (OC) Ultra fine (Half-tone) (OC) Fine text (Half-tone) (SPF) Super fine (Half-tone) (SPF) Ultra fine (Half-tone) (SPF) Fine text (Half-tone) (CIS) Super fine (Half-tone) (CIS) Ultra fine (Half-tone) (CIS)

2)

Using the numeric keypad, select the number that corresponds to the scan mode for which to make adjustments.

3)

Press the Start key.

4)

Adjust the gamma by entering an appropriate value through the numeric keypad. A larger value provides larger gamma gradient and higher image contrast.

1

5)

Press the Start key. This applies the adjustment value.

Select 0 - 5, and press [START] key.

Scanned images must be visually checked to ensure the postadjustment image gamma.

Press [START] key, or press [SYSTEM SETTINGS] key.

ADJ 12 Common image quality

SIMULATION 46-22 EXP.LEVEL SETUP SCANNER(NORMAL), INPUT VALUE 0-99, AND PRESS START. 0.AUTO

adjustments for all of copy, scan, and fax modes

50

Item 0 1 2 3 4 5

3)

AUTO 1.0 2.0 3.0 4.0 5.0

Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5

Setting range 0 – 99

(Common image quality adjustment items for all of copy, scan, and fax modes) Default 50

Enter the number that corresponds to the following adjustment item using the numeric keypad. (Choose from numbers 0 to 5.) * Auto mode * Manual mode (print density adjustment level) For manual mode, select the number that corresponds to the image density adjustment level (1 to 5). (Choose from numbers 1 to 5.)

4)

Press the Start key.

5)

Enter the image density adjustment value.

6)

Press the P or Start key.

Adjustment Item List Correct the image density in original table mode/SPF mode (Copy mode) Set up the auto mode operation for copy, scan, and fax

Simulation for adjustment 46-20 46-19

12-A Original table mode/SPF mode image density correction (copy mode) Used to adjust the copy density correction in the DSPF copy mode for the document table copy mode. The adjustment is made so that the copy density becomes the same as that of the document table copy mode. This adjustment is needed in the following situations: * The CCD unit has been replaced. * U2 trouble has occurred. * The MFP control PWB has been replaced.

Scanned images must be visually checked to ensure the postadjustment image density.

* The EEPROM on the MFP control PWB has been replaced. * The scanner control PWB has been replaced. * The EEPROM on the scanner control PWB has been replaced. * One or more parts of the scanner (reading) section have been replaced. * The CIS unit has been removed. * The CIS unit has been replaced. * The DSPF unit has been removed. * The DSPF unit has been replaced.

MX-M700N ADJUSTMENTS 6 – 37

1)

Go through the modes specified in Simulation 46-20. SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START. 0. TRAY SELECT 1 1. PRINT START 2. EXP LEVEL 1 3. SPF(FRONT) 128 4. SPF(REAR) 128 5. DSPF 128

1

12-B Set up the auto mode operation for copy, scan, and fax This adjustment is needed in the following situations: * U2 trouble has occurred. * The MFP control PWB has been replaced. * The EEPROM on the MFP control PWB has been replaced.

Select other than 0 - 2, and press Press [SYSTEM SETTINGS] key. [START] key.

* The scanner control PWB has been replaced.

SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS START. 1.SPF(FRONT)

* The EEPROM on the scanner control PWB has been replaced. 1)

128

SIMULATION 46-19 EXP.MODE SETUP. SELECT 1-2, AND PRESS START. 1.AE MODE 1 2.AE STOP MODE(COPIER) 1 3.AE STOP MODE(SCANNER)0 4.AE STOP MODE(FAX) 0

Select 1, Press [START] key. Press [SYSTEM SETTINGS] and press 㩷 key, or terminate copying. [START] key. SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT.

NOW PRINTING.

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 0, and press [START] key.

Go through the modes specified in Simulation 46-19.

Select 1, and press [START] key.

SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 1-6, AND PRESS START. (FEED TRAY) 2.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT 6.LCC

Press [SYSTEM SETTINGS] key.

SIMULATION 46-19 EXP.MODE SETUP. INPUT VALUE 1-2, AND PRESS START. 1.AE MODE

1

1

Select 2, and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

Select 2, 3, or 4 and press [START] key.

SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START. (EXP. LEVEL SELECT) 3.1.0 4.1.5 5.2.0 6.2.5 7.3.0 8.3.5 9.4.0 10.4.5 11.5.0

SIMULATION 46-19 EXP.MODE SETUP. INPUT VALUE 0-1, AND PRESS START. 2.AE STOP MODE(COPIER)

1

Item 0

1 2

PRINT START EXP LEVEL

3

SPF (FRONT)

4

SPF (REAR)

5

2)

TRAY SELECT

DSPF

Content Paper feed tray selection 1: TRAY1 2: TRAY2 3: TRAY3 4: TRAY4 5: Manual feed 6: Side LCC Print start (Default) Exposure level selection 3:Exposure level1.0 4:Exposure level1.5 5:Exposure level2.0 6:Exposure level2.5 7:Exposure level3.0 8:Exposure level3.5 9:Exposure level4.0 10:Exposure level4.5 11:Exposure level5.0 SPF (front) (front frame side) SPF (front) (rear frame side) (rear frame side) DSPF (Back surface)

Setting range –

0

Default

AE fixed mode

0 – 255

128

Set value 1

2

– –

0 1

Item

Default

Image quality priority mode (Normal mode) * Gamma is sharp to provide high contrast images. Toner consumption priority mode * Gamma is mild to provide low contrast images. AE fixed OFF AE fixed ON

2

1 (COPIER) 0 (SCANNER/ FAX)

2)

Select "1 AE MODE" using the numeric keypad.

3)

Press the Start key.

4)

Using the numeric keypad, select the number that corresponds to the operation spec.

5)

Press the Start key. Pressing the Start key applies the setting.

(Auto copy mode operation setting)

Using the mumeric keypad, select the number that corresponds to the mode for which to make adjustments. DSPF front frame side (front face copy), DSPF rear frame side (front face copy), DSPF (back side copy) (Choose from numbers 3 to 5.)

3)

Mode

–

AE mode

– –

Press [START] key, or press [SYSTEM SETTINGS] key.

Press the Start key.

4)

Enter the density correction value using the numeric keypad.

5)

Press the P or Start key.

6)

Make two copies (one in original table mode and the other in DSPF mode) and compare the copies in of density.

Repeat steps 4 to 6 until both copies provide the same density.

1)

Using the numeric keypad, select the number that corresponds to the mode for which to make adjustments. (Choose from numbers 2 to 4.)

2)

Press the Start key.

3)

Using the numeric keypad, select the number that corresponds to the operation mode.

4)

Press the Start key.

AE fix OFF: Density (exposure) is automatically controlled on a real time basis. (The density level is dynamically changed according to the original's pattern.) AE fix ON: The density of the leading edge of the original is detected and used to determine the overall density (exposure) level. (The overall density level is fixed.)

MX-M700N ADJUSTMENTS 6 – 38

ADJ 13 Adjusting the fusing paper

ADJ 14 Adjusting the paper size

guide position

detection

This adjustment is needed in the following situations: * Paper is jammed in or around the fusing section. * Imperfect images, deformed images, or wrinkles are produced in the paper lead edge section or the rear edge section. Adjust the fusing paper guide position by loosening the fusing paper guide fixing screws and the sliding the fusing paper guide in the arrow direction.

14-A Adjust the paper width sensor for the manual paper feed tray This adjustment is needed in the following situations: * The manual paper feed tray section has been disassembled. * The manual paper feed tray unit has been replaced. * U2 trouble has occurred. * The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. 1)

Go through the modes specified in Simulation 40-2.

SIMULATION 40-2 BY TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1. MAX. POSITION 2. POSITION 1 3. POSITION 2 4. MIN. POSITION

1

Select 1, and press [START] key. Press [SYSTEM SETTINGS] key. SIMULATION 40-2 BY TRAY ADJUSTMENT. MAX. POSITION ··· COMPLETE (or "ERROR")

Select 2, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 40-2 BY TRAY ADJUSTMENT. POSITION 1 ··· COMPLETE (or "ERROR")

Select 3, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 40-2 BY TRAY ADJUSTMENT. POSITION 2 ··· COMPLETE (or "ERROR")

When shipping, it is fixed to the position which is one scale (0.5mm) over the center.

Select 4 and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 40-2 BY TRAY ADJUSTMENT. MIN. POSITION ··· COMPLETE (or "ERROR")

2)

Open the manual paper feed guide to the maximum width position.

MX-M700N ADJUSTMENTS 6 – 39

3)

Select MAX. POSITION using the numeric keypad.

14-B Adjust the paper width sensor for paper feed tray 3 This adjustment is needed in the following situations: * The paper feed tray section has been disassembled. * The paper feed tray unit has been replaced. * U2 trouble has occurred. * The PCU PWB has been replaced. * The EEPROM of the PCU PWB has been replaced. 1)

Go through the modes specified in Simulation 40-12. SIMULATION 40-12 TRAY3 ADJUSTMENT. SELECT 1-2, AND PRESS START. 1. MAX. POSITION 2. MIN. POSITION

4)

Press the Start key.

Select 1, and press [START] key. Press [SYSTEM SETTINGS] key.

The maximum width detection level is recognized. 5)

Press the SYSTEM SETTINGS key.

6)

Set the manual paper feed guide to the width for the A4R size.

7)

Select POSITION 1 using the numeric keypad.

8)

Press the Start key.

9)

Press the SYSTEM SETTINGS key.

1

SIMULATION 40-12 TRAY3 ADJUSTMENT. MAX. POSITION ··· COMPLETE (or "ERROR")

The A4R width detection level is recognized. Press [START] key.

Press [SYSTEM SETTINGS] key.

10) Set the manual paper feed guide to the width for the A5R size. 11) Select POSITION 2 using the numeric keypad.

SIMULATION 40-12 TRAY3 ADJUSTMENT. MIN. POSITION ··· COMPLETE (or "ERROR")

12) Press the Start key. The A5R width detection level is recognized. 13) Press the SYSTEM SETTINGS key. 14) Open the manual paper feed guide to the minimum width position.

Press the Start key.

* When each of the above operations has been completed, the "COMPLETE" message appears; when any of the operations has failed, the "ERROR" message appears.

5)

Press the SYSTEM SETTINGS key.

6)

Open the paper feed guide to the maximum width position.

51 2

Select MAX. POSITION using the numeric keypad.

4)

71 2

3)

The minimum width detection level is recognized.

81 2

16) Press the Start key.

A4

Open the paper feed guide to the maximum width position.

11

2)

A5

B5

A4

B5 B4

A3

15) Select MIN. POSITION using the numeric keypad.

The maximum width detection level is recognized.

MX-M700N ADJUSTMENTS 6 – 40

2)

Open the DSPF paper feed guide to the maximum width position.

* The scanner PWB has been replaced.

3)

Select MAX. POSITION using the numeric keypad.

* The EEPROM on the scanner PWB has been replaced.

4)

Press the Start key.

5)

Press the SYSTEM SETTINGS key.

7)

Select MIN. POSITION using the numeric keypad.

8)

Press the Start key. The maximum width detection level is recognized.

* When each of the above operations has been completed, the "COMPLETE" message appears; when any of the operations has failed, the "ERROR" message appears.

14-C Adjust the paper width sensor for the DSPF paper feed tray This adjustment is needed in the following situations: * The paper feed tray section has been disassembled. * The paper feed tray unit has been replaced. * U2 trouble has occurred.

1)

The maximum width detection level is recognized.

Go through the modes specified in Simulation 53-6. SIMULATION 53-6 SPF TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1.MAX.POSITION 2.POSITION 1 3.POSITION 2 4.MIN.POSITION

6)

Open the DSPF paper feed guide to the width for the A4R size.

7)

Select POSITION 1 using the numeric keypad.

8)

Press the Start key.

9)

Press the SYSTEM SETTINGS key.

1

The A4R width detection level is recognized. 10) Open the DSPF paper feed guide to the width for the A5R size.

Select 1, and press [START] key.

11) Select POSITION 2 using the numeric keypad.

Press [SYSTEM SETTINGS] key.

12) Press the Start key. The A4R width detection level is recognized.

SIMULATION 53-6 SPF TRAY ADJUSTMENT. MAX.POSITION ... COMPLETE (or “ERROR”)

Select 2, and press [START] key.

13) Press the SYSTEM SETTINGS key. 14) Open the DSPF paper feed guide to the minimum width position.

Press [SYSTEM SETTINGS] key.

SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 1 ... COMPLETE (or “ERROR”)

Select 3, and press [START] key.

Press [SYSTEM SETTINGS] key.

SIMULATION 53-6 SPF TRAY ADJUSTMENT. POSITION 2 ... COMPLETE (or “ERROR”)

15) Select MIN. POSITION using the numeric keypad. Select 4 and press [START] key.

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 53-6 DSPF TRAY ADJUSTMENT. MIN.POSITION ... COMPLETE (or “ERROR”)

16) Press the Start key. The maximum width detection level is recognized. * When each of the above operations has been completed, the "COMPLETE" message appears; when any of the operations has failed, the "ERROR" message appears.

MX-M700N ADJUSTMENTS 6 – 41

ADJ 15 Adjusting the original size detection (in original table mode)

15-B Adjust the sensitivity of the original size sensor 1)

Go through the modes specified in Simulation 41-2. SIMULATION 41-2 PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START. (PLEASE OPEN THE ORIGINAL COVER.) 1. NO ORIGINAL 2. A3 ORIGINAL

This adjustment is needed in the following situations:

15-

1

* The original size sensor section has been disassembled. * The original size sensor section has been replaced.

Select 1, and press [START] key.

* U2 trouble has occurred.

Press [SYSTEM SETTINGS] key.

* The scanner control PWB has been replaced. * The EEPROM on the scanner control PWB has been replaced.

SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL ··· COMPLETE (or "ERROR at PD1 PD2...") A3 ORIGINAL ··· INCOMPLETE

15-A Adjust the detection point of the original size sensor (in original table mode) 1)

Go through the modes specified in Simulation 41-1. Select 2 and press [START] key. (Error) SIMULATION 41-1 PD SENSOR CHECK.. OCSW PD1 PD2 PD3

2)

PD4

PD5

PD6

PD7

Press [START] key, or press [SYSTEM SETTINGS] key.

SIMULATION 41-2 PD SENSOR ADJUSTMENT. NO ORIGINAL ··· COMPLETE A3 ORIGINAL ··· COMPLETE (or "ERROR at PD1 PD2...")

Gradually turn over the original detection arm unit in the arrow direction, and loosen the original cover switch actuator adjusting screw so that the OCSW indicator changes from inverse video to normal video when the arm unit top reaches a height of 32r0.5mm from the table glass. Then move the actuator to adjust its position. (If the original cover switch turns on in improper timing, the original detection mechanism mail fail to operate correctly.)

2)

Open the original cover. With nothing placed on the original table, select NO ORIGINAL using the numeric keypad.

3)

Press the Start key.

4)

Set A3 (11" x 17") paper on the original table, and select A3 ORIGINAL using the numeric keypad.

5)

Press the Start key. This sets the sensor level with an original detected.

This sets the sensor level with no original detected.

When each of the above operations has been completed, the "COMPLETE" message appears; when any of the operations has failed, the "ERROR" message appears.

ADJ 16 Adjusting the touch

Original detection arm unit

coordinates This adjustment is needed in the following situations: * The operation has been replaced. * U2 trouble has occurred. * The MFP control PWB has been replaced.

32+ -5mm

* The EEPROM on the MFP control PWB has been replaced. 1)

Go through the modes specified in Simulation 65-1.

SIMULATION 65-1

Table glass

Original cover switch actuator

2)

Press the four cross mark points. Pressing the cross mark points correctly results in gray display. When the touch adjustment is complete with the four points pressed, the sub-number entry screen for simulation reappears. If any error is detected, the touch returns to adjustment mode.

NOTE: Never use something with a sharp tip (such as a needle or pin) to press the touch . MX-M700N ADJUSTMENTS 6 – 42

(12 V supply voltage adjustment)

ADJ 17 Adjusting the supply voltage

5)

Apply a digital multi-meter to the DC sub PWB 12 V line (CN4, 1 pin) and GND (CN4, 6 pin).

This adjustment is needed in the following situations:

6)

Turn RV102 on the DC sub power supply PWB so that the voltage is 12 V.

* One or more parts of the DC main power supply unit have been replaced. * One or more parts of the DC sub power supply unit have been replaced. (24 V supply voltage adjustment) 1)

Apply a digital multi-meter to the DC main PWB 24 V line (CN3, 1 pin) and GND (CN3, 4 pin).

2)

Turn RV202 on the DC main power supply PWB so that the voltage is 24 V.

GND +24V (CN3, 4pin) (CN3, 1pin)

RV202

(38 V supply voltage adjustment) 3)

Apply a digital multi-meter to the DC main PWB 38 V line (CN8, 1 pin) and GND (CN8, 4 pin).

4)

Turn RV201 on the DC main power supply PWB so that the voltage is 38 V.

RV201

GND +38V (CN8, 4pin) (CN8, 1pin)

MX-M700N ADJUSTMENTS 6 – 43

GND +12V (CN4, 6pin) (CN4, 1pin)

RV102

MX-M700N

[7] SIMULATION

Counters 5GTXKEG/WCN

1. Adjustment value/Simulation and storage data

ADU paper feed counter

Staple counter

A. Simulation adjustment value/ Set value data Each controller is provided with an EEPROM. The adjustment/set values are collected to the MFP controller. If they are changed, they are sent back and saved.

LCD

MFP CONTROLLER

Punch counter

Main unit right-side paper exit counter When the value is changed, it is sent and saved.

Side LCC paper feed counter Inserter counter Saved adjustment value send (When the power is turned on, etc.) ENGINE CONTROLLER

SCANNER CONTROLLER

B. Each storage data (1)

Saddle staple counter

Heater lamp temperature (Center, normal control)

F Web Send counter

Lead edge adjustment

Toner supply time (Block IC CHIP) Drum rotating time (Block IC CHIP) Total counter Maintenance counter Developing counter Drum counter Toner cartridge counter Valid paper counter

Tray 1 paper feed counter

Tray 2 paper feed counter

Tray 3 paper feed counter

Tray 4 paper feed counter

Manual paper feed counter

Adjustment value Developing bias voltage value

Others Serial number

Cleaning mode Developing bias voltage value Main high voltage adjustment Transfer charger voltage value Transfer belt cleaning voltage value Toner concentration reference value Density correction start set time (Developer unit) Density correction rotation time (Developer tank) Density correction amount (Developer tank)

Trouble history

Correction execution direction, upper/lower limit (Developer tank) Toner concentration temperature correction (low temperature side) correction amount Toner concentration temperature correction (low temperature side) set temperature Toner concentration temperature correction (low temperature side) release temperature Toner concentration temperature correction (high temperature) correction amount Toner concentration temperature correction (high temperature side) judgment temperature

Tray 1 size Tray 2 size Manual destination information

Tray 3 destination information Tray 4 destination information Tray 1 paper remaining quantity data Tray 2 paper remaining quantity data Tray 3 paper remaining quantity data

Others White paper exit count setting

Trouble memory mode setting

Fusing operation mode (Prevention against curl) CE mark conforming operation mode Maintenance cycle Print stop setting when developer life over Saddle alignment operation priority mode

Led edge void set value Rear edge void set value Side edge setting Print off-center adjustment value Resist amount adjustment value Laser power adjustment value PPD1 sensor adjustment Process correction inhibit allow set value Developing bias rising correction wait time Developing bias rising correction adjustment value Built-in finisher jogger position adjustment Saddle adjustment value

(Data saved by the PCU PWB)

Counters Drum rotation time counter (Accumulated time) Developer unit rotation time counter

Adjustment value Toner concentration temperature correction (high temperature side) judgment voltage Toner concentration temperature correction (high temperature side) correction value Toner concentration temperature correction (low temperature side) release time Toner concentration temperature correction (high temperature side) toner concentration delay time Multi-purpose width adjustment value Manual width adjustment value

(2)

(Data saved by the scanner control PWB)

Counters Scan counter SPF paper counter SPF stamp counter

Tray 4 paper remaining quantity data Final toner concentration sensor output value Toner cartridge IC CHIP destination

Counter mode setting

MX-M700N SIMULATION 7 – 1

Adjustment value Document lead edge adjustment value Document off-center adjustment value Document image loss amount adjustment value Document image loss amount adjustment value SPF resist amount adjustment value Exposure motor speed adjustment value Platen document detection adjustment value SPF size width detection adjustment value Touch adjustment value Exposure level adjustment value gamma change value OC/SPF exposure correction value Shading adjustment value (CCD/CIS) CCD shading start position adjustment value

Others Exposure mode set value Scanner serial number

(3)

Counters Copy counter Printer counter FAX receive counter FAX send counter All valid paper counter Trouble counter JAM counter

(4)

2. General

(Data saved by the MFP control PWB) Adjustment value FAX SOFT SW., etc.

Others Trouble history JAM history Destination setting Language setting Toner save mode setting 13" setting Auditor setting Counter mode setting Trouble memory mode setting Center binding mode AMS setting PC/MODEM communication trouble detection YES/NO setting Tag number set value Printers set values Network set value

The simulation has the following functions to grasp the machine operating status, identify the trouble position and causes in an earlier stage, and make various setups and adjustments speedily for improving the serviceability of the machine. 1)

Various adjustments

2)

Setting of the specifications and functions

3)

Canceling troubles

4)

Operation check

5)

Counters check, setting, clear

6)

Machine operating conditions (operation hysteresis), data check, clear

7)

Various (adjustments, setting, operation, counters, etc.) data transfer

The operating procedures and displays depend on the form of the operation of the machine.

A. Basic operation (1)

* Entering the simulation mode 1)

(Detailed list)

Refer to the "3. List of simulation codes".

Starting the simulation Copy mode key ON → Program key ON → Asterisk (*) key ON → CLEAR key ON → Asterisk (*) key ON → Ready for input of a main code of simulation

2)

Entering a main code with the 10-key -> [START] key. ON

3)

Entering a sub code with the 10-key -> [START] key. ON

4)

Select an item with the scroll key and the item key.

5)

The machine enters the mode corresponding to the selected item. Press [START] key. or EXECUTE key to start the simulation operation. To cancel the current simulation mode or to change the main code and the sub code, press the setup key.

* Canceling the simulation mode to return to the normal mode 1)

Press CA key.

(Note for the simulation mode) • Do not turn OFF the power switch on the operation when the machine is in the simulation mode. When executing the operation of mentioning above, a malfunction may be resulted. In this case, turn OFF/ON the main power source. • Before entering the simulation mode, check to insure that neither print data nor FAX data are receiving.

MX-M700N SIMULATION 7 – 2

Select copy mode

Press the Program key.

Press the asterisk (*) key.

Press the clear key.

Press the Program key. Press the SYSTEM SETTINGS key

Standby for entry of SIM code. Enter the main code of SIM with the 10-key. The main code of SIM is displayed.

NO

Press the START button. YES

Standby for entry of SIM sub code

YES

<Exclusion type> You have to exit simulation mode before entering into this mode for self printing type.

Is there a sub code ? NO

Enter SIM sub code with the 10-key.

Select the mode and the item with the scroll key and the item key.

Press the START button.

NO

YES

If there is no item.

Operation check ?

NO

Do you want to perform another simulation ?

NO

YES

NO

Do you want to end the simulation ?

Press the EXECUTE button and OK button.

The display is made according to the selected some and the item.

Data clear ?

YES

NO

Press the EXECUTE button and OK button. The selected mode and the item are cleared.

Adjustments or setting (counter data change) ?

NO

Operation is made according to the selected mode and the item. (Other modes)

The display is made according to the selected mode and the item. Do you want to change the content ?

NO

The changed content is stored.

YES

Enter the new setting and ;'5 adjustment values.

The simulation mode is canceled.

Press the EXECUTE button and OK button.

Operation is made according to the selected mode and item.

Operating conditions check ?

YES

Is it the same simulation main code? In the power OFF/ON type simulation, OFF/ON message is Press the SYSTEM displayed by the SETTINGS key SYSTEM SETTINGS key. YES

Press the EXECUTE button and OK button.

MX-M700N SIMULATION 7 – 3

YES

Press the clear all key.

3. List of simulation codes Main code

Sub code

1

1 2 1 2 3 2 3 10 30 31 32 2 3 1 2 3 4 1 2 3 1

2

3

4 5

6

7

8

9 10 13 14 15 16 17 21 22

23

6 8 1 2 6 17 18 19 1 2 1 2

1 1 2 3 4 5 6 7 8 9 10 11 12 13 19 30 31 2 80

Operation content Mirror scan operation Optical system sensor check SPF operation aging SPF sensor check SPF individual load check Finisher sensor check Finisher individual load check Finisher setting Inserter sensor check Inserter load operation Inserter tray value setting LCC sensor check LCC individual load check LCD/LED test Heater lamp test Copy lamp test Discharge lamp test Transport system load operation (Clutch/Solenoid) Fan motor test Transfer separation motor operation Operation registration (jam detection:No, developing tank detection:No, aging and maintenance warmup:No, intermittent operation:Yes, shading:No etc.) Intermittent aging cycle setting Warm-up time display (No aging) DV bias setting Main charger grid voltage setting Transfer voltage setting Transfer roller setting Transfer cleaning roller setting Fusing bias setting (Not used) ADU output test ADU sensor check Toner motor activation Toner rest sensor check U1 trouble cancellation Trouble cancellation LCC trouble cancellation U2 trouble cancellation PF trouble cancellation Maintenance cycle set up Counter data display JAM/Trouble counter data display Paper jam history Trouble history ROM version data display Data print mode Key operator code display ORG/Staple counter data display Paper feed counter data display System information FAX counter data display SPF JAM history Process data display Network scanner counter display OSA vendor ID display (Application Communication) OSA vendor ID display (External ) JAM/trouble data print mode Data print mode

MX-M700N SIMULATION 7 – 4

Data save destination/Target MFP Scanner Engine { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { {

{

{ {

{

{ {

{

{

{

{ {

{ { { { { (FAX) { { { {

Main code

Sub code

24

1 2 3 4 5 6 7 9 10 11 15 1 2 2 3 5 6 10 18 30 35 38 41 50 52 68 1 5 1 2 1 2 7 11 12 1 2 3 1 3 1 2 4 5 9 12 14 16 2 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 31 39 45

25 26

27 30 40

41

43 44

46

Operation content JAM/Trouble counter data clear Paper feed counter clear ORG/Staple counter clear Maintenance counter data clear Developer counter data clear Copy counter data clear Drum/Toner counter data clear Printer/Other counter data clear FAX counter data clear Various rotation time timer clear Network scanner counter data clear Toner concentration sensor monitor Auto developer adjustment Size setting Auditor setting Counter mode setting Destination setting Network scanner trial mode setting Toner save mode setting CE mark conformity control inhibit/allow setting Trouble memory mode setting Print stop setting when life over Center binding mode AMS setting Black-White reverse function valid/invalid setting White paper exit count-up setting CA key cancel function valid/invalid PC/MODEM communication trouble (U7-00) detection YES/NO setting Tag number setting Main unit sensor check Tray sensor check Manual paper feed size width detection check Manual paper feed size width detection level adjustment Manual paper feed size width detection adjustment value input MPT size width detection check MPT size width detection level adjustment Document size detection photo sensor check Document size detection photo sensor detection level Document size detection photo sensor light receiving/detection level check Fusing temperature control temperature setting (Normal/Energy-save mode) Fusing roller RPM setting. Process correction inhibit/allow setting DM/ID sensor gain adjustment Standard patch density setting Patch making reference condition setting Process control data display Process control patch data display Temperature/humidity sensor output monitor Toner concentration reference value check Copy exposure level adjustment (binary) Copy exposure level adjustment/individual setting (Text binary) Copy exposure level adjustment, individual setting (Text/Photo binary) Copy exposure level adjustment, individual setting (Photo binary) FAX exposure level adjustment (1 mode auto adjustment) FAX exposure level adjustment, individual setting (Normal text) FAX exposure level adjustment, individual setting (Fine) FAX exposure level adjustment, individual setting (Super Fine) FAX exposure level adjustment, individual setting (Ultra Fine) Shading reference value change (Gain adjustment) gamma change (Copier mode) Exposure mode setting OC/SPF exposure correction Scanner exposure level adjustment (1 mode auto adjustment) Scanner exposure level adjustment, individual setting (Normal text) Scanner exposure level adjustment, individual setting (Fine) Scanner exposure level adjustment, individual setting (Super Fine) Scanner exposure level adjustment, individual setting (Ultra Fine) gamma change (Scanner mode) Copy sharpness setting FAX sharpness setting FAX exposure level adjustment, individual setting (600dpi)

MX-M700N SIMULATION 7 – 5

Data save destination/Target MFP Scanner Engine { { { { { { { { { { { { (FAX) { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { {

Main code

Sub code

48

1 5 1 1 2 5 6 7 10 12 27 2 6 7 8 1 2 3 1 1 1 2 3 4 1 2 3 6 7 8 9 10 11 1 2 7 1 1 2

49 50

51 53

55

56 60 61

62

63

64 65

Operation content Magnification ratio adjustment (by Input/Output) Motor speed adjustment Firmware update Copy lead edge adjustment (Document table) Lead edge adjustment (Document table simple type) Print lead edge adjustment Copy lead edge adjustment (SPF) Copy lead edge adjustment (SPF simple type) Print off-center adjustment Document off-center adjustment Document image loss setting (FAX send/scanner mode) Resist amount adjustment SPF size width detection level adjustment SPF size width detection adjustment value input SPF scan position adjustment Engine soft SW change and check Scanner soft SW change and check Controller soft SW change and check Data transfer ICU image DRAM read/write check LSU operation check Laser power setting (Copier) Laser power setting (FAX) Laser power setting (Printer) Hard disk format Hard disk read/write check Hard disk read/write check (All areas) HDD self diag Self diag error log print Hard disk format (Excluding the system area) HDD format (system area) Job complete list delete Document filing data delete Shading check Shading execution White plate scan start position adjustment Self print Touch adjustment Touch check

MX-M700N SIMULATION 7 – 6

Data save destination/Target MFP Scanner Engine { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { {

Main code

Sub code

66

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 23 24 25 26 27 29 30 31 32 33 34 35 36 39 42 43 60 16

67

Operation content FAX-related soft SW setting check/change FAX-related soft SW clear (Excluding FAX adjustment values) FAX-related memory check Signal send mode (Signal send level: Max.) Signal send mode (Signal send level: Soft SW setting) Confidential code print Image memory content output Voice message reproduction (Signal send level: Max.) Voice message reproduction (Signal send level: Soft SW setting) Image memory clear 300bps signal send (Signal send level: Max.) 300bps signal send (Signal send level: Soft SW setting) Dial number registration Dial test (10PPS make time setting & delivery test) Dial test (20PPS make time setting & send test) Dial test (DTMF signal adjustment & send test) DTMF signal send mode (Signal send level: Max.) DTMF signal send mode (Signal send level: Soft SW setting) Address book backup (WR TO FLASH) Address book backup (RD FROM FLASH) FAX information print FAX program FAST memory data clear MODEM dial-in FAX number registration MODEM dial-in telephone number registration Voice warp transfer destination registration Address book clear TEL/LIU status change check TEL/LIU setting Receive data check Signal detection check Communication time measurement display MODEM program rewrite MFP controller I/F check FAX destination registration Reload of the PIC program Setting of the PIC adjustment value (Secret) ACR data registration Network card check

MX-M700N SIMULATION 7 – 7

Data save destination/Target MFP Scanner Engine { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { { {

4. Details of simulation

The operation can be stopped with the [SYSTEM SETTINGS] key. 1 2 3

1

HIGH SPEED (220mm/sec) LOW SPEED (110mm/sec) TOP SPEED (360mm/sec)

High speed Low speed Top speed

1-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the scanner (read) unit and its control circuit.

Section

Optical (Image scanning)

SIMULATION 2-1 SPF AGING TEST. SELECT 1-3, AND PRESS START. 1. HIGH SPEED 2. LOW SPEED 3. TOP SPEED

2㩷

Operation/Procedure 1)

Select the operation mode with 10-key.

2)

Press [START] key.

Purpose

Operation test/Check

The scanner performs scanning at the speed corresponding to the operation mode.

Function (Purpose)

Used to check the operations of the sensors and detectors in the automatic document feeder unit and the related circuits.

Section

DSPF

1 2

HIGH SPEED LOW SPEED

2-2

High speed (220mm/s) Low speed (110mm/s)

Operation/Procedure The sensor and detector operation conditions are displayed.

SIMULATION 1-1 SCANNER CHECK. SELECT 1-2, AND PRESS START. 1. HIGH SPEED 2. LOW SPEED

The active sensors and detectors are highlighted.

1

1-2 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of sensor and detector in the scanning (read) section and the related circuit.

Section

Optical (Image scanning)

Operation/Procedure The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted. • The scanner (read) unit is in the home position.: "MHPS" section is highlighted. • The scanner (read) unit is not in the home position.: "MHPS" is normally displayed. MHPS

SSET SOCD SCOV SPED2 SPED1 SPPD1 SPPD2 SPPD3 SPPD4 SPOD SWDn SPLSn CISSET STSET STUD STLD SWD_LEN SWD_AD

SPF sensor Open/close sensor Paper feed cover sensor Document set sensor (Lower) Document set sensor (Upper) Document transport sensor 1 Document transport sensor 2 Document transport sensor 3 Document transport sensor 4 Document exit sensor Document width sensor (n → 1 (inside) to 6 (outside)) Document length sensor (n → 1 (inside) to 2 (outside)) CIS installation detection Stamp unit installation sensor Tray upper limit sensor Tray lower limit sensor SPF guide plate position (unit: 0.1mm) SPF document width detection volume output AD value

Optical system home position SIMULATION 2-2 SPF SENSOR CHECK. SSET SOCD SCOV SPED1 SPPD1 SPPD2 SPPD4 SPOD SWD6 SWD4 SWD3 SWD2 SPLS2 SPLS1 CISSET STUD STLD SWD_LEN: 2100 SWD_AD: 600

SIMULATION 1-2 SCANNER SENSOR CHECK.. MHPS

2

SPED2 SPPD3 SWD5 SWD1 STSET

2-3

2-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the automatic document feeder unit and the control circuit.

Section

DSPF

Select the operation mode with 10-key.

2)

Press [START] key.

Operation test/Check

Function (Purpose)

Used to check the operations of the loads in the automatic document feeder unit and the control circuits.

Section

DSPF

Operation/Procedure 1)

Operation/Procedure 1)

Purpose

2)

Select the number corresponding to the target of operation check with 10-key. Press the [START] key. The load selected in procedure 1 is operated.

The SPF repeat paper feed, transport, and paper exit at the speed corresponding to the operation mode.

The operation can be stopped with the [SYSTEM SETTINGS] key.

MX-M700N SIMULATION 7 – 8

PI11S

Saddle paper exit detection

PI12 PI12S

Tray 2 paper detection Semi-circular roller phase detection

PI13S

Guide HP detection

PI14 PI14S

PI17S

Buffer path detection Paper holding plate lead edge position detection Finisher t detection Paper holding plate lead edge position detection Door open detection Buffer path entry port paper detection Vertical path paper detection

PI18 PI18S

Oscillating guide open detection Saddle No. 1 paper detection

PI19 PI19S

Tray lift motor clock detection 2 Saddle No. 2 paper detection

3

PI20 PI20S

Oscillation guide clock detection Saddle No. 3 paper detection

3-2

PI21 PI21S

Staple lead edge detection Paper folding HP detection

PI22 PI23 PI24 PI25 MS1

1 2 3 4 5 6 7 8 9 10 11 12 13

MOTOR (T) MOTOR (H) MOTOR (L) STRBC STRC SPFC SRRC SRRBC STRRC STRRBC STMPS SLUM SPFFAN

Motor top speed Motor high speed Motor low speed Document transport brake clutch Document feed transport clutch Document feed clutch Document resist clutch Document resist brake clutch Document feed resist clutch Document feed resist brake clutch Stamp solenoid Lift up motor SPF fan motor

SIMULATION 2-3 SPF LOAD TEST. SELECT 1.MOTOR(T) 2.MOTOR(H) 4.STRBC 5.STRC 8.SRRBC 9.STRRC 12.SLUM 13.SPFFAN

PI15 PI15S PI16 PI17

1-13, AND PRESS START. 3.MOTOR(L) 6.SPFC 7.SRRC 10.STRRBC 11.STMPS

2

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of sensor and detector in the finisher and the related circuit.

Section

Finisher

The operating conditions of the sensors and detectors are displayed.

MS1S

Staple drive HP detection Tray 2 lift motor clock detection 1 Tray 2 lift motor clock detection 2 Tray 2 HP detection Front door / Upper door open detection Saddle entry port door detection

The active sensors and detectors are highlighted.

MS2 MS2P

Oscillation guide close detection Punch front door open detection

MS2S

Front door open detection

MS3 MS3S

Safety area detection Paper exit door open detection

MS4 MS4S

Shutter close detection Saddle staple presence detection 2

MS5S

Stitch operation HP detection 2

MS6S

Saddle staple presence detection 1

MS7 MS7S

Cartridge detection Stitch operation HP detection 1

MS8 MS9

Staple empty detection Tray approaching detection

Operation/Procedure

PI1 PI1P

Entry port paper detection Punch side resist HP detection

PI1S PI2P

Paper holding plate motor clock detection Punch motor clock detection

PI2S

Front door open detection

PI3 PI3P

Paper exit detection Punch HP detection

PI3S

Paper exit cover open detection

PI4S

Paper folding motor clock detection

PI5 PI5S

Shutter open detection Alignment plate HP detection

PI6 PI6S

Alignment guide HP detection Saddle tray paper detection

PI7 PI7S

PI9 PI9S

Staple shift HP detection Paper positioning plate HP detection Tray 1 HP detection Paper positioning plate HP detection Tray 1 lift motor clock detection 1 Entry port cover open detection

PI10 PI11

Paper exit motor clock detection Tray 1 paper detection

PI8 PI8S

When the punch unit is installed When the saddle unit is installed When the punch unit is installed When the saddle unit is installed When the punch unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed

When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed

When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed

When the saddle unit is installed When the punch unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed When the saddle unit is installed

SIMULATION 3-2 FINISHER SENSOR CHECK. PI10 PI20 PI19 PI9 PI22 PI1 PI14 PI3 PI17 PI12 PI11 MS8 PI21 MS7 PI18 PI5 PI8 PI6 PI7 MS2 MS4 MS1 MS3 PI16 PI15 MS9 PI24 PI23 PI25 (PI2P) (MS2P) (PI1P) (PI3P) <MS7S> <MS5S> <MS3S> <MS2S><MS1S><MS6S><MS4S>

( ) : Added when the punch unit is installed. < > : Added when the saddle unit is installed.

MX-M700N SIMULATION 7 – 9

3-3 3

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the load in the finisher and the control circuit.

Section

Finisher

4 5

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press the [START] key.

6

7

The load selected in procedure 1 is operated. The operation can be stopped with the [SYSTEM SETTINGS] key. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SL7 SL6 SL5 SL3 SL2 SL1 M10 M9 M8 M7 M6 M5 M4 M3 M2 M1

Belt wait solenoid Wait solenoid Paddle solenoid Buffer exit port solenoid Buffer entry port solenoid Flapper solenoid Tray 2 lift motor Entry port transport motor No. 2 transport motor Oscillation motor Staple motor Tray 1 lift motor Stapler shift motor Alignment motor Paper exit motor No. 1 transport motor

M2P M1P

SL4S SL2S SL1S M8S M7S M6S M5S M4S M3S M2S M1S

37 - 63, 1STEP: 0.15mm 35 - 57, 1STEP: 0.26mm

5 - 35, 1STEP: 1mm

5 - 35, 1STEP: 1mm

1

3-30 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the sensors and detectors in the inserter and the related circuit.

Section

Inserter

Operation/Procedure The operating conditions of the sensors and detectors are displayed.

Punch side resist motor Punch motor

The active sensors and detectors are highlighted.

(When the saddle unit is installed. 19 20 21 22 23 24 25 26 27 28 29

Setting range 68 - 132, 1STEP: 0.152 mm

SIMULATION 3-10 FINISHER SETTING.㵘SELECT㵘1-7䋬AND PRESS START. 1. SADDLE POSITION 2. ALIGNMENT㵘POSITION 3. STAPLE㵘POSITION 4. PUNCH㵘CENTER 5. PUNCH㵘HOLE 6. TRAY WAITING POSITION(S-SIZE) 7. TRAY WAITING POSITION(L-SIZE)

(When the punch unit is installed) 17 18

Item Staple binding position adjustment Punch center adjustment Punch hole position adjustment (Paper feed direction) Stack tray standby position adjustment (Small size) Stack tray standby position adjustment (Large size)

Transport plate solenoid No. 2 paper deflection plate solenoid No. 1 paper deflection plate solenoid Paper holding motor Stitch motor: Front Stitch motor: Rear Saddle alignment motor Paper positioning motor Guide motor Paper folding motor Saddle transport motor

SIMULATION 3-3 FINISHER LOAD TEST.㵘SELECT㵘1-㵘䋬AND PRESS START.

TH_SEN TS_SEN T_SEN EMP_SEN REG_SEN TIM_SEN JCK_SEN H_SEN HI_SEN HYK_SEN S_SW KC_SEN P_ST_SW P_MO_SW P_PN_SW

Sub tray pull-out detection Sub tray storage detection Inserter tray paper size detection Inserter tray empty detection Inserter resist sensor Inserter timing sensor detection Inserter cover open/close sensor Inserter reverse sensor Inserter paper exit sensor Inserter reverse unit open/close sensor Inserter set SW Base cover open/close sensor Inserter start SW Inserter staple mode select SW Inserter punch select SW

2㩷 SIMULATION 3-30 INSERTER SENSOR CHECK. TH_SEN TS_SEN REG_SEN TIM_SEN HI_SEN HYK_SEN P_ST_SW P_MO_SW

3-10 Purpose

Adjustment

Function (Purpose)

Finisher (AR-F16) adjustment

Section

Finisher

Operation/Procedure 1)

Select the number that corresponds to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press [START] key. (The entered value is stored.)

1 2

Item Saddle stitch/folding position adjustment Alignment position adjustment

Setting range 192 - 208, 1STEP: 0.25 mm 2 - 18, 1STEP: 0.35 mm

MX-M700N SIMULATION 7 – 10

T_SEN JCK_SEN S_SW P_PN_SW

EMP_SEN H_SEN KC_SEN

3-31 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the loads in the inserter and the related circuits.

Section

Inserter

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press the [START] key.

LTD LUD LLD LPED LTOD LCD LOSW LRE +24VM LLSW

Transport sensor Tray upper limit sensor Tray lower limit sensor Tray paper presence/empty sensor Main unit connection detection sensor Tray insertion detection Upper open/close detection SW Lift motor encoder sensor 24V power monitor Upper limit SW

The load selected in procedure 1 is operated. The operation can be stopped with the [SYSTEM SETTINGS] key. 1 2 3 4 5 6

K_MOT Y_MOT H_MOT F_SOL R_CL P_LED

Reverse motor Horizontal transport motor Inserter reverse Inserter flapper solenoid Inserter resist clutch Inserter operation upper LED

SIMULATION 4-2 LCC SENSOR CHECK. LTD LUD LTOD LCD +24VM LLSW

LLD LOSW

LPED LRE

4-3

SIMULATION 3-31 INSERTER LOAD TEST. SELECT 1-6, AND PRESS START. 1. K_MOT 2. Y_MOT 3. H_MOT 4. F_SOL 5. R_CL 6. P_LED

2

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the loads in the paper feed section (large capacity tray) and the related circuit.

Section

Paper feed

Operation/Procedure 3-32

1)

Select the number corresponding to the target of operation check with 10-key. Press the [START] key.

Purpose

Setting (Adjustment)

2)

Function (Purpose)

Inserter paper width detection level setting.

The load selected in procedure 1 is operated.

Section

Inserter

The operation can be stopped with the [SYSTEM SETTINGS] key.

Operation/Procedure

<Side LCC>

1)

Select the number corresponding to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the setting (adjustment) value with 10-key.

4)

Press the [START] key. 1 2 3 4

MAX. POSITION POSITION 1 POSITION 2 MIN. POSITION

Max. position Adjustment point 1 Adjustment point 2 Min. width

SIMULATION 3-32 INSERTER TRAY VALUE SETTING. SELECT 1-4, AND PRESS START. 1. MAX. POSITION : 72 2. POSITION 1 : 380 3. POSITION 2 : 710 4. MIN. POSITION : 804

1

1 2 3 4 5 6

LTM LLM LPFCL LPSL LTCL LTLSL

LCC transport motor LCC lift motor Paper feed clutch LCC paper feed solenoid LCC transport clutch Tray lock solenoid D

SIMULATION 4-3 LCC LOAD TEST. SELECT 1-6, AND PRESS START. 1.LTM 2.LLM 3.LPFCL 4.LPSL 5.LTCL 6.LTLSL

2

5 5-1

4

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the display, LCD in the operation , and control circuit. Operation (Display/Operation key)

4-2 Purpose

Operation test/Check

Section

Function (Purpose)

Used to check the operations of the sensors and detectors in the paper feed section (large capacity tray) and the related circuit.

Operation/Procedure

Section

Paper feed

The contrast changes every 2sec from the current level to MAX → MIN → the current level. During this period, each LED is lighted. 㩷SIMULATION 5-1

Operation/Procedure The operating conditions of the sensors and detectors are displayed. The active sensors and detectors are highlighted.

MX-M700N SIMULATION 7 – 11

5-2

6

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the heater lamp and the control circuit.

Section

Fusing/Paper exit

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press [START] key. The load selected in procedure 1 performs ON/OFF operation.

6-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the paper transport system loads (clutch, solenoid) and the control circuit.

Section

Paper transport Transport)

Operation/Procedure

Press [SYSTEM SETTINGS] key to stop the operation of the load.

1)

The ON/OFF operation of the selected heater lamp is repeated every 500ms five times.

2)

1 2 3

HL1 (LOWER) HL2 (UPPER) HL3 (LEFT)

(Discharge/Switchback/

Select the number corresponding to the target of operation check with 10-key. Press the [START] key. The load selected in procedure 1 is operated. The operation can be stopped with the [SYSTEM SETTINGS] key.

Heater lamp 1 (Lower) Heater lamp 2 (Upper) Heater lamp 3 (Left)

SIMULATION 5-2 HEATER LAMP TEST. SELECT 1-3 ,AND PRESS START. 1.HL1(LOWER) 2.HL2(UPPER) 3.HL3(LEFT)

2

5-3 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the scanner lamp and the control circuit.

Section

Optical (Image scanning)

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press [START] key. The load selected in procedure 1 turns ON for 10sec. The operation can be stopped with the [SYSTEM SETTINGS] key.

NOTE: CIS: only when the DSPF is installed. SIMULATION 5-3 COPY LAMP TEST. SELECT 1-2, AND PRESS START. 1.COPY LAMP 2.CIS

1

5-4 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the discharge lamp and the related circuit.

Section

Process

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

MSWPR HLPR DR MM DM DVM TURM TRM POM1 POM2_FW POM2_RV VPM RRC PSBC PSPS T1PFC T2PFC HPFC T1PUS T2PUS HPLS T1LUM T2LUM DSKPFC1 DSKPFC2 M1PFC M2PFC M1PUS M2PUS M1LUM M2LUM TRC_LCC FUM MPFPUS MPFC MPFGS WEBM

MSW reset signal Heater power relay signal DC power relay signal Main motor Drum motor Developing motor Transfer separation motor PS front motor Paper exit motor 1 Paper exit motor 2 forward rotation Paper exit motor 2 reverse rotation Paper transport motor Resist roller clutch signal Brake clutch signal Separation pawl Tray 1 paper feed clutch Tray 2 paper feed clutch Horizontal transport clutch Tray 1 pickup solenoid Tray 2 pickup solenoid Relay path clock solenoid Tray 1 lift-up motor Tray 2 lift-up motor Desk paper transport clutch upstream side Desk paper transport clutch downstream side Tray 3 paper feed clutch Tray 4 paper feed clutch Tray 3 pickup solenoid Tray 4 pickup solenoid Tray 3 lift-up motor Tray 4 lift-up motor Desk clutch sync signal Fusing motor Manual pickup solenoid Manual paper feed clutch signal Manual paper feed gate solenoid Fusing web feed motor

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press [START] key. The load selected in procedure 1 turns ON for 30sec. The operation can be stopped with the [SYSTEM SETTINGS] key. SIMULATION 5-4 DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START. 1.DL

1

SIMULATION 6-1 FEED OUTPUT CHECK. SELECT 1- 37, AND PRESS START. 1.MSWPR 2.HLPR 3.DR 4.MM 5.DM 6.DVM 7.TURM 8.TRM 9.POM1 10.POM2_FW 11.POM2_RV 12.VPM 13.RRC 14.PSBC 15.PSPS 16.T1PFC 17.T2PFC 18.HPFC 19.T1PUS 20.T2PUS 21.HPLS 22.T1LUM 23.T2LUM 24.DSKPFC1 25.DSKPFC2 26.M1PFC 27.M2PFC 28.M1PUS 29.M2PUS 30.M1LUM 31.M2LUM 32.TRC_LCC 33.FUM 34.MPFPUS 35.MPFC 36.MPFGS 37.WEBM

MX-M700N SIMULATION 7 – 12

2

6-2

7

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of each fan motor and its control circuit.

Section

Others

Operation/Procedure

7-1 Purpose

Setting

Function (Purpose)

Used to set the operating conditions of aging. —

1)

Select the number corresponding to the target of operation check with 10-key.

Section

2)

Press the [START] key.

Operation/Procedure

The load selected in procedure 1 operates.

1)

Select the number corresponding to the operating condition of aging with 10-key.

The operation can be stopped with the [SYSTEM SETTINGS] key. 1

VFM-EX

2

CFM-UP

3 4 5 6

CFM-R CFM-DC CFM-DV CFM-ICU /HDD

7 8

ALL CFM-AD

Exhaust fan motor (VFM-EX1, 2, 3, VFM-BKL, VFM-BKU) Heat exhaust fan motor (Paper exit upper) (CFM-U1, 2, 3, VFM-BKR) Cooling fan motor (Right side) (CFM-R1, 2, 3) Cooling fan motor (Power source) (CFM-DC1, 2) Cooling fan motor (Developing) (CFM-DV) Cooling fan motor (Controller/HDD) (CFM-ICU/ HDD) All fans control* Cooling fan motor (paper exit center) (CFM-U4)

* All fans: All the fans controlled by the engine. (Exhaust fan motor, heat exhaust fan motor (paper exit upper), cooling fan motor (right side) cooling fan motor (power source), cooling fan motor (developing), cooling fan motor (paper exit center)) SIMULATION 6-2 FAN MOTOR CHECK. SELECT 1-8, CAND PRESS START. 1. VFM-EX 2. CFM-UP 3. CFM-R 4. CFM-DC 5. CFM-DV 6. CFM-ICU /HDD 7. ALL 8. CFM-AD

2

In that case, the number corresponding to one of 0 - 6 mode and the number corresponding to one of 10, 20, and 30 mode are added and the sum number is entered. 2)

Press the [START] key. The condition selected in procedure 1) is set.

The setting of this simulation is kept valid until the power is turned off. 0 1 2 3

4 5 6 +10

+20 +30

6-3 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the transfer unit and the related circuit.

Section

Process (Transfer)

1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press the [START] key. The load selected in procedure 1 operates. The transfer belt performs /separation with the OPC drum. The operation can be stopped with the [SYSTEM SETTINGS] key.

NOTE: Before disassembling the transfer unit, use this simulation to separate the transfer unit from the OPC drum. TURM (RELEASE) TURM (T)

NO MISS FEED DETECTION AGING AGING/NO MISS FEED DETECTION. AGING/NO MISS FEED DETECTION/NO WARM UP/ NO TEMPERATURE CONTROL. NO WARM UP. AGING/INTERVAL. AGING/INTERVAL/NO MISS FEED DETECTION. NO PROCESS UNIT CHECK. NO SHADING. NO PROCESS UNIT CHECK/NO SHADING.

No jam detection/ no warmup/ no fusing temperature control, aging mode No warm-up Intermittent aging mode No jam detection intermittent aging mode Above +10: No process unit (including the developing unit) detection Above +20: No shading Above +30: No process unit detection /no shading

SIMULATION 7-1 AGING TEST SETTING. SELECT 0-36, AND PRESS START. 0.NO MISS FEED DETECTION 1.AGING 2.AGING/NO MISS FEED DETECTION. 3.AGING/NO MISS FEED DETECTION/ NO WARM UP/NO TEMPERATURE CONTROL. 4.NO WARM UP. 5.AGING/INTERVAL. 6.AGING/INTERVAL/NO MISS FEED DETECTION. +10:NO PROCESS UNIT CHECK. +20:NO SHADING. +30:NO PROCESS UNIT CHECK/NO SHADING.

Press [START] key to start registration and operation. The operation mode is kept until the power is turned off or setting is made again.

Transfer unit separation state Transfer unit state

SIMULATION 6-3 TURM CHECK. SELECT 1-2 CAND PRESS START. 1. TURM(RELEASE) 2. TURM(T)

No jam detection Aging mode No jam detection, aging mode

2

Operation/Procedure

1 2

The combined mode of 0 - 6 mode and 10, 20, or 30 mode can be set.

2

MX-M700N SIMULATION 7 – 13

7-6

Item

Purpose

Setting

Function (Purpose)

Used to set the intermittent aging cycle.

Section

—

1 2 3 4 5 6 7

Operation/Procedure 1)

Enter the intermittent aging cycle (unit: sec) with 10-key.

2)

Press [START] key.

AUTO CHARACTER MIX PHOTO PRINTER FAX PLUS

Auto mode Text mode Text/Photo mode Photo mode Printer mode FAX mode Reverse developing bias voltage

The time entered in procedure 1) is set.

Setting range 0 - 750

Default 495

0 - 250

150

* Set range of interval time: 1 - 999 (sec) SIMULATION 8-1 DV BIAS SETTING. SELECT 1-7, AND PRESS START. 1.AUTO 495 2.CHARACTER 495 3.MIX 495 4.PHOTO 495 5.PRINTER 495 6.FAX 495 7.PLUS 150

SIMULATION 7-6 INTERVAL AGING CYCLE SETUP. INPUT TIME AND PRESS START. (1-999, UNIT: sec)

1

10 8-2 7-8 Purpose

Setting

Function (Purpose)

Used to set the warm-up time display YES/ NO.

Section

—

Purpose

Adjustment/Operation test/Check

Function (Purpose)

Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure

Operation/Procedure 1)

Select the number corresponding to the warm-up time display YES/NO.

2)

Press [START] key, and the number selected in procedure 1) is set.

* The setting of this simulation is kept valid until the power is turned off.

1)

Select the number that corresponds to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press the [START] key. (The set value is stored, and the output corresponding to the set value is outputted for 30sec.)

* The warm-up time is displayed by sec.

The operation can be stopped with the [SYSTEM SETTINGS] key. SIMULATION 7-8 WARM UP TIME DISPLAY. ARE YOU SURE? 1. YES 2. NO

(The main charger grid output voltage adjustment and output check can be made in each print mode.) Item

1

1 2 3 4 5 6

8

AUTO CHARACTER MIX PHOTO PRINTER FAX

Auto mode Text mode Text/Photo mode Photo mode Printer mode FAX mode

Setting range 200 - 1000

Default 580

8-1 Purpose

Adjustment/Operation test/Check

Function (Purpose)

Used to check and adjust the operations of the developing voltage of each color and the control circuit.

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1) 2)

Select the number that corresponds to the adjustment item with 10-key.

SIMULATION 8-2 MAIN GRID SETTING. SELECT 1-6, AND PRESS START. 1.AUTO 580 2.CHARACTER 580 3.MIX 580 4.PHOTO 580 5.PRINTER 580 6.FAX 580

1

8-6 Purpose

Adjustment/Operation test/Check

Function (Purpose)

Used to check and adjust the operation of the transfer voltage and the control circuit. (Transfer mode)

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)/Transfer

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press the [START] key. (The set value is stored, and the output corresponding to the set value is outputted for 30sec.)

The operation can be stopped with the [SYSTEM SETTINGS] key. (The developing bias output voltage adjustment and output check can be made in each print mode.)

Operation/Procedure 1)

Select the number that corresponds to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press the [START] key. (The set value is stored, and the voltage corresponding to the set value is outputted for 30sec.)

MX-M700N SIMULATION 7 – 14

: '07 Feb 15

1

The operation can be stopped with the [SYSTEM SETTINGS] key.

The operation can be stopped with the [SYSTEM SETTINGS] key.

(The transfer output voltage adjustment and output check can be made in each print mode.)

(The output voltage of the transfer CL roller cleaning/transfer CL roller print mode can be adjusted and checked.)

1

Setting range

Item 1

FRONT

2

BACK

Front surface print mode Back surface print mode

0 - 800

Default 55/62 70 (ppm) (ppm) 300 400

Item Transfer CL roller (Print) Transfer CL roller (Cleaning)

CRHV PLUS CRHV MINUS

Set range 0 - 250 0 - 250

Default 200 200

SIMULATION 8-18 TRANSFER CLEANING ROLLER SETTING. SELECT 1-2, AND PRESS START. 1.CRHV PLUS 200 2.CRHV MINUS 200

1

SIMULATION 8-6 THV+ SETTING. SELECT 1-2, AND PRESS START. 1.FRONT 400 2.BACK 400

1 8-19

8-17 Purpose

Operation test/Check

Function (Purpose)

Used to check and adjust the operation of the transfer voltage and the related circuit. (Transfer belt cleaning mode)

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Purpose

Adjustment/Operation test/Check

Function (Purpose)

Used to check and adjust the fusing bias voltage and the control circuit. (Not used)

Section

Fusing

Operation/Procedure 1)

Select the number that corresponds to the adjustment item with 10-key.

2)

Operation/Procedure

Press the [START] key. (The voltage is outputted for 30sec.)

1)

Select the number that corresponds to the adjustment item with 10-key.

The operation can be stopped with the [SYSTEM SETTINGS] key.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

The output voltage can be adjusted with the adjustment volumes VR101/VR102 on the high voltage PWB (fusing bias).

4)

Press the [START] key. The set value is stored, and the voltage corresponding to the set value is outputted for 30sec.

Fusing bias (-) Fusing bias (+)

The operation can be stopped with the [SYSTEM SETTINGS] key.

1 2 3

SHV FRONT SHV BACK THV-

Front side Back side Out put

Setting range 0 - 600 0 - 600 0 - 75

450 450 10

1

8-18 Purpose

Adjustment/Operation test/Check

Function (Purpose)

Used to check and adjust the voltage of the transfer CL roller cleaning/transfer CL roller print mode and the control circuit. Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1)

Select the number that corresponds to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press the [START] key.

1

Default

SIMULATION 8-17 TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START. 1.SHV FRONT 450 2.SHV BACK 450 3.THV- 10

Section

Adjustment VR VR 101 VR 102

SIMULATION 8-19 FUSING BIAS CHECK. SELECT 1, AND PRESS START. 1.FBIAS

The transfer output voltage adjustment and output check can be made in the transfer belt cleaning mode. Item

Item FBIAS

(The set value is stored, and the voltage corresponding to the set value is outputted for 30sec.)

9 9-1 Purpose

Operation test/Check

Function (Purpose)

Used to check and adjust the operation of the load (clutch/solenoid) in the duplex section and the control circuit.

Section

Duplex

Operation/Procedure 1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press [START] key. The load selected in procedure 1 is operated.

The operation can be stopped with the [SYSTEM SETTINGS] key. 1 2 3

ADUM1 ADUM2 DGS

ADU motor 1: Upstream ADU motor 2: Downstream ADU gate solenoid

SIMULATION 9-1 ADU OUTPUT CHECK. SELECT 1-3, AND PRESS START. 1. ADUM1 2. ADUM2 3. DGS

MX-M700N SIMULATION 7 – 15

1

9-2

10-2

Purpose

Operation test/Check

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the sensors and detectors in the duplex section and its control circuit.

Function (Purpose)

Used to check the operations of the toner remaining quantity sensor and the related circuit.

Section

Duplex

Section

Process (Developing)

Operation/Procedure

Operation/Procedure

The sensor and detector operation conditions are displayed.

1)

Press the [START] key.

The active sensors and detectors are highlighted. DSW_ADU AINPD APPD1 APPD2

ADU ADU ADU ADU

The toner motor rotates 2 turns, and the toner presence/empty in the toner hopper is displayed.

cabinet open/close detection paper entry detection transport detection 1 transport detection 2

SIMULATION 9-2 ADU SENSOR CHECK. DSW_ADU AINPD APPD1

Toner empty: Normal display Toner remained: Highlighted display SIMULATION 10-2 TONER REST SENSOR CHECK. PRESS START. TFSD

APPD2

13

10

13-0 10-1

Purpose

Clear/Cancel (Trouble etc.)

Function (Purpose)

Used to cancel the self-diag "U1" trouble. (Only when FAX is installed.) FAX

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the toner motor and the related circuit.

Section

Section

Process (Developing)

Operation/Procedure

Operation/Procedure

1)

Select 1 (YES) with 10-key.

1)

Select the number corresponding to the target of operation check with 10-key.

2)

Press [START] key. (The trouble display is canceled.)

2)

Press the [START] key. The load selected in procedure 1) is operated for 10sec.

1

YES

2

NO

The operation can be stopped with the [SYSTEM SETTINGS] key. NOTE: Do not execute this simulation with toner in the toner bottle and the intermediate toner tank. Excessive toner may enter the developing section, causing overtoner. Check that there is no toner in the toner bottle and the intermediate toner tank or disassemble the toner motor before executing this simulation. TM1 TM2

After canceling U1 trouble, the machine returns to the main code entry standby mode. Without canceling U1 trouble, the machine returns to the main code entry standby mode.

SIMULATION 13 U1 TROUBLE CANCELLATION. ARE YOU SURE? 1. YES 2. NO

1

Toner motor 1 Toner motor 2

14 SIMULATION 10-1 TONER MOTOR ACTIVATION. SELECT 1-2, AND PRESS START 1. TM1 2. TM2

1

14-0 Purpose

Clear/Cancel (Trouble etc.)

Function (Purpose)

Used to cancel excluding the self-diag U1/ LCC/U2/PF troubles.

Section

Trouble

Operation/Procedure 1)

Select 1 (YES) with 10-key.

2)

Press [START] key. (The trouble display is canceled.) 1

YES

2

NO

MX-M700N SIMULATION 7 – 16

After canceling the trouble other than U1, U2, PF, and LCC, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.

SIMULATION 14 TROUBLE CANCELLATION. (OTHERS) ARE YOU SURE? 1. YES 2. NO

17

1

15 15-0

17-0 Purpose

Clear/Cancel (Trouble etc.)

Function (Purpose)

Used to cancel the PF troubles (when the copy inhibit command from the host computer is received).

Section

Communication unit (RIC/MODEM etc.)

Operation/Procedure

Purpose

Clear/Cancel (Trouble etc.)

1)

Select 1 (YES) with 10-key.

Function (Purpose)

Used to cancel the self-diag ”U6-09, F3-12, 22” (large capacity paper feed tray, paper feed trays 1, 2) troubles.

2)

Press [START] key. (The trouble display is canceled.)

Section

LCC

Operation/Procedure 1)

Select 1 (YES) with 10-key.

2)

Press [START] key. (The trouble display is canceled.) 1

YES

2

NO

1

YES

2

NO

After canceling the PF trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.

SIMULATION 17 PF TROUBLE CANCELLATION. ARE YOU SURE? 1. YES 2. NO

After canceling the LCC trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.

SIMULATION 15 LCC TROUBLE CANCELLATION. ARE YOU SURE? 1. YES 2. NO

1

1

21 21-1

16

Purpose

Setting

Function (Purpose)

Used to set the maintenance cycle.

Section

Specifications - Counter

Operation/Procedure 16-0 Purpose

Clear/Cancel (Trouble etc.)

Function (Purpose)

Used to cancel the self-diag U2 troubles.

Section

MFP control PWB, PCU PWB, scanner control PWB

1)

Enter the number corresponding to the maintenance timing display.

2)

Press [START] key. The condition entered in procedure 1) is set. Maintenance timing display

Operation/Procedure 1)

Select 1 (YES) with 10-key.

2)

Press [START] key. (The trouble display is canceled.) 1

YES

2

NO

After canceling the U2 trouble, the machine returns to the main code entry standby mode. Without canceling the trouble, the machine returns to the main code entry standby mode.

SIMULATION 16 U2 TROUBLE CANCELLATION. ARE YOU SURE? 1. YES 2. NO

0 1 - 300 999

Default (Differs depending on the model.) Maintenance display at 1K - 300K No maintenance display

Setting range 0 - 999

SIMULATION 21-1 MAINTENANCE CYCLE SETUP. INPUT VALUE 0-999, AND PRESS START. 0: DEFAULT 1-300: MAINTENANCE CYCLE (1K-300K) 999: FREE

1

MX-M700N SIMULATION 7 – 17

0

22-3

22 22-1

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check misfeed positions and the misfeed count of each position. (If the misfeed count is considerably great, it may be judged as necessary to repair.)

Section

Sections other than DSPF section

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.)

Operation/Procedure

—

The history of paper jams and misfeed is displayed.

Section

The misfeed history is displayed sequentially from the latest one. The max. 100 items of misfeed history can be recorded. The data may be used to identify trouble position.

Operation/Procedure Various print counter values are displayed. TOTAL DRUM TONER DEVE MAINTENANCE TOTAL OUTPUT COPIES PRINTER FAX I-FAX output DOC FILING OUTPUT RIGHT SIDE OUTPUT OTHERS F WEB SEND

Total counter Drum counter Toner counter Developer counter Maintenance counter Total output page number Copy effective paper counter Printer counter FAX print counter iFAX print counter Document filing print counter Right paper exit counter Other print counter (List print , etc.) Fusing web cleaning feed counter

SIMULATION 22-1 COUNTER DATA DISPLAY. TOTAL: ******** DRUM: ******** TONER: ******** DEVE: ******** MAINTENANCE: ******** TOTAL OUTPUT: ******** COPIES: ******** PRINTER: ******** FAX OUTPUT: ******** I-FAX OUTPUT:******** DOC FILING OUTPUT:******** RIGHT SIDE:******** OTHERS: ******** F WEB SEND:********

22-2 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the total numbers of misfeed and troubles. (When the number of misfeed is considerably great, it is judged as necessary for repair. The misfeed rate is obtained by dividing this count value with the total counter value.)

Section

Trouble

Operation/Procedure The paper jam/trouble counter value is displayed. PAPER JAM SPF JAM TROUBLE

Number of paper jams Number of SPF jams Number of troubles

SIMULATION 22-2 JAM/TROUBLE COUNTER DATA DISPLAY. PAPER JAM: ******** SPF JAM: ******** TROUBLE: ********

(Jam cause code) Code NO_JAM_CAUSE

Description No jam. Also used to cancel a jam.

TRAY1 PFD2_NM1 PFD2_NM2 PFD2_NAD PFD2_ST1 PFD2_SM1 PFD2_SM2 PFD2_SAD

Tray 1 paper feed jam (PFD2 not-reached) PFD2 not-reached jam (Tray 3 feed paper) PFD2 not-reached jam (Tray 4 feed paper) PFD2 not-reached jam (ADU re-feed paper) PFD2 remaining jam (Tray 1 feed paper) PFD2 remaining jam (Tray 3 feed paper) PFD2 remaining jam (Tray 4 feed paper) PFD2 remaining jam (ADU re-feed paper)

PPD_NMF

PPD1 not-reached jam (Manual feed tray feed paper) PPD1 not-reached jam (Tray 1 feed paper) PPD1 not-reached jam (Tray 2 feed paper) PPD1 not-reached jam (Tray 3 feed paper) PPD1 not-reached jam (Tray 4 feed paper) PPD1 not-reached jam (LCC paper feed paper) PPD1 not-reached jam (ADU re-feed paper)

PPD_NT1 PPD_NT2 PPD_NM1 PPD_NM2 PPD_NLC PPD_NAD PPD_SMF PPD_ST1 PPD_ST2 PPD_SM1 PPD_SM2 PPD_SLC PPD_SAD

PPD1 remaining paper) PPD1 remaining PPD1 remaining PPD1 remaining PPD1 remaining PPD1 remaining PPD1 remaining

jam (Manual feed tray feed jam jam jam jam jam jam

(Tray 1 feed paper) (Tray 2 feed paper) (Tray 3 feed paper) (Tray 4 feed paper) (LCC paper feed paper) (ADU re-feed paper)

PPD_PRI

PPD1 jam (Image ready request is not sent from ICU.)

PSD_N PSD_S POD1_N POD1_S POD1_LDV POD2_N POD2_SR

PSD not-reached jam (currently not detected) PSD remaining jam (currently not detected) POD1 not-reached jam POD2 remaining jam POD1 jam (LCV is turned OFF.) POD2 not-reached jam POD2 remaining jam (When paper is discharged on the right side of the machine.) POD2 remaining jam (When paper is discharged on the left side of the machine.)

POD2_SL

AINPD_N AINPD_S APPD1_N APPD1_S APPD2_N APPD2_S

ADU paper entry sensor not-reached jam ADU paper entry sensor remaining jam ADU transport sensor 1 not-reached jam ADU transport sensor 1 remaining jam ADU transport sensor 2 not-reached jam ADU transport sensor 2 remaining jam

DESK1 M1PFD_N2 M1PFD_S1 M1PFD_S2 DESK2

Tray 3 paper feed jam (M1PFD not-reached) M1PFD not-reached jam (Tray 4 feed paper) M1PFD remaining jam (Tray 3 feed paper) M1PFD remaining jam (Tray 4 feed paper) Tray 4 paper feed jam (M2PFD not-reached)

MX-M700N SIMULATION 7 – 18

Code M2PFD_S

Description M2PFD remaining jam

MPRD2_N2 MPRD2_NM

MPRD2 not-reached jam (Tray 2 feed paper) MPRD2 not reached jam (Manual paper feed tray feed paper) MPRD2 not-reached jam (LCC paper feed paper) MPRD2 remaining jam (Tray 2 feed paper) MPRD2 remaining jam (Manual paper feed tray feed paper) MPRD2 remaining jam (LCC paper feed paper) Tray 2 paper feed jam (MPRD1 not-reached) MPRD1 not-reached jam (Manual paper feed tray feed paper) MPRD1 not-reached jam (LCC paper feed paper) MPRD1 remaining jam (Tray 2 feed paper) MPRD1 remaining jam (Manual paper feed tray feed paper) MPRD1 remaining jam (LCC paper feed paper) MPFD2 not-reached jam (Manual paper feed tray feed paper) MPFD2 not-reached jam (LCC paper feed paper) MPFD2 remaining jam (Manual paper feed tray feed paper) MPFD2 remaining jam (LCC paper feed paper) MPFD2 remaining jam (Manual paper feed tray feed paper) MPFD1 remaining jam LPPD not-reached jam LPPD remaining jam LPPD jam (No reply in a certain time after preliminary paper feed from LCC and issuing the paper feed command.)

MPRD2_NL MPRD2_S2 MPRD2_SM MPRD2_SL TRAY2 MPRD1_NM MPRD1_NL MPRD1_S2 MPRD1_SM MPRD1_SL MPFD2_NM MPFD2_NL MPFD2_SM MPFD2_SL BPT MPFD1_S LPPD_N LPPD_S LPPD_LCC

SIMULATION 22-3 PAPER JAM HISTORY. *******,*******,*******,*******,*******,*******,*******,*******,*******,******* *******,*******,*******,*******,*******,*******,*******,*******,*******,******* *******,*******,*******,*******,*******,*******,*******,*******,*******,******* *******,*******,*******,*******,*******,*******,*******,*******,*******,******* *******,*******,*******,*******,*******,*******,*******,*******,*******,******* ···············

(10 lines, 80 digits = 800 characters) 22-4 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the trouble (self diag) history.

Section

—

Operation/Procedure The trouble history is displayed. The trouble history is displayed sequentially from the latest one. The max. 100 items can be stored. (The oldest one is deleted sequentially.) The trouble position can be identified by the data.

SIMULATION 22-4 TROUBLE HISTORY. **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** **-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-**,**-** ···············

(10 lines, 80 digits = 800 characters) 22-5

LCC LTD_S

LCC paper feed jam (LTD not-reached jam ) LTD remaining jam

FES_N FES_S FFPS_N FFPS_S FEXIT_S FSTPL FPNCH FDOP FIN_TIME

FINISHER entry port sensor not-reached jam FINISHER entry port sensor remaining jam FINISHER Saddle not-reached jam FINISHER Saddle remaining jam FINISHER bundle exit remaining jam FINISHER Staple jam FINISHER punch JAM FINISHER door open JAM FINISHER Abnormal paper interval jam

REG_SEN_N

INSERTER Resist sensor not-reached jam (When inserter paper feed) INSERTER Resist sensor remaining jam (When inserter paper feed) INSERTER Timing sensor not-reached jam (When inserter paper feed) INSERTER Timing sensor remaining jam (When inserter paper feed) INSERTER Paper exit sensor not-reached jam (When inserter paper feed) INSERTER Paper exit sensor not-reached jam (Main unit paper feed) INSERTER Paper exit sensor remaining jam INSERTER Reverse sensor not-reached jam (When entering into the reverse path.) INSERTER Reverse sensor not-reached jam (When discharging to the reverse path.) INSERTER Reverse sensor remaining jam (When entering into the reverse path.) INSERTER Reverse sensor remaining jam (When discharging to the reverse path.)

REG_SEN_S TIM_SEN_N TIM_SEN_S HI_SEN_NI HI_SEN_NP HI_SEN_S H_SEN_NF H_SEN_NB H_SEN_SF H_SEN_SB

Purpose

Others

Function (Purpose)

Used to check the ROM version of each unit (section).

Section

—

Operation/Procedure The ROM version of each section can be checked. When there is any problem in the software, use this simulation to check the ROM version of each section and revise the version if necessary. S/N MFP (LANGUAGE) BOOT FAX PCU SCANNER FINISHER SADDLE UNIT LCC INSERTER

Engine section serial number MFP controller (Language version) MFP controller BOOT ROM FAX controller PCU controller Scanner controller Finisher controller Saddle unit Side LCC Inserter

SIMULATION 22-5 ROM VERSION DATA DISPLAY. S/N: 0000000000 MFP: 1.00 (LANGUAGE: 1.00) PCU: 1.00 BOOT: SCANNER: 1.00 FAX: FINISHER: 1.00 SADDLE UNIT: 1.00 LCC: INSERTER: 1.00

MX-M700N SIMULATION 7 – 19

1.00 1.00 1.00

22-6 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to output the list of the setting and adjustment data (simulations, FAX soft switch, counters).

Section

—

SIMULATION 22-8 ORG./STAPLE COUNTER DATA DISPLAY. SPF: ******** SCAN: ******** STAPLER: ******** PUNCH: ******** STAMP: ******** SADDLE STAPLER: ******** INSERTER: ******** INSERTER OFF LINE: ********

Operation/Procedure When installing or servicing this machine, execute this simulation to print and save various setting and adjustment data for next servicing. (For example, memory trouble, PWB replacement, etc.) 1)

Enter 1 with 10-key.

2)

Press the [START] key.

The various setting and adjustment data are printed out. (The print paper cannot be selected optionally.) 0

TRAY SELECT

1

PRINT START

22-9 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the number of use (print quantity) of each paper feed section.

Section

Paper feed, ADU

Operation/Procedure The values of the paper feed related counters are displayed.

TRAY SELECT auto only (Selection is not allowed.) PRINT START

SIMULATION 22-6 DATA PRINT MODE. SELECT SETTING, AND PRESS START. 0. TRAY SELECT :AUTO ONLY 1. PRINT START

1

22-7

TRAY1 TRAY2 TRAY3 TRAY4 BPT ADU LCC

Tray 1 use quantity Tray 2 use quantity Tray 3 use quantity Tray 4 use quantity Manual feed tray use quantity Duplex paper feed quantity Side LCC use quantity

SIMULATION 22-9 PAPER FEED COUNTER DATA DISPLAY. TRAY1: ******** TRAY2:******** TRAY3: ******** TRAY4:******** BPT: ******** ADU: ******** LCC: ********

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to display the key operator code. (This simulation is used when the customer forgets the key operator code.)

22-10

Section

—

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

The key operator code is displayed.

Function (Purpose)

Used to check the system configuration (option, internal hardware).

SIMULATION 22-7 KEY OPERATOR CODE DISPLAY. CODE: *****

Section

—

Operation/Procedure

Operation/Procedure

The system configuration is displayed. (The model names of the installed devices and options are displayed.)

22-8 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the number of use of the finisher, the SPF, and the scan (reading) unit.

Section

Scanner (Image scanning) - Finisher

Operation/Procedure The values of the finisher counter, the scanner (read), counter, and the SPF related counters are displayed. SPF SCAN STAPLER PUNCH STAMP SADDLE STAPLER INSERTER INSERTER OFF LINE

Document feed quantity Number of times of scan Number of times of staple Number of times of punch Number of times of SPF finish stamp Number of times of saddle staple Number of times of inserter Number of inserter off-line times

MACHINE FINISHER LCC INSERTER PUNCH SYSTEM MEMORY HDD NIC NSCN PS3 FAX FAX MEMORY STAMP PCU TYPE I-FAX

MX-M700N SIMULATION 7 – 20

(Model code) NONE/ (Model code) NONE/ (Model code) NONE/ (Model code) NONE/ (Model code) Memory capacity (MB) Hard disk capacity (MB) NONE/ (Network Expansion kit) NONE/ (Network scanner) NONE/ (PS3 expansion kit) NONE/ (Model code) FAX expansion memory capacity (MB) Finish stamp NONE/ (Model code) PCU PWB type (JPN: Japan, EX: EX Japan) None/ (Internet FAX expansion kit)

(Model code list) Item MACHINE

22-11 Display (Model code) (Model code) (Model code) (Model code) (Model code) (Model code)

INSERTER FINISHER

PUNCH

----(Model code) ----(Model code) (Model code) ----(Model code) (Model code) (Model code) (Model code)

LCC

MEMORY

HD NIC

----(Model code) (Model code) 0MB ***MB 0MB ****MB ----(Model code)

PS3 expansion kit FAX

NETWORK SCANNER

----(Model code) ----(Model code) ----(Model code)

EXPANSION MEMORY

----(Model code)

FINISH STAMP

Data security kit I-FAX

----(Model code) ----(Model code) ----(Model code)

Content Network optional model (55 ppm) Network optional model (62 ppm) Network optional model (70 ppm) Network print standard equipment model (55 ppm) Network print standard equipment model (62 ppm) Network print standard equipment model (70 ppm) Inserter not installed Inserter installed After-process unit not installed Finisher installed Saddle finisher installed Punch unit not installed Punch unit installed (2-hole) Punch unit installed (2-hole/3-hole auto select) Punch unit installed (4-hole) Punch unit installed (4-hole, wide) Side LCC not installed Side LCC installed Side LCC installed (large size ) Expansion memory not installed Expansion memory ***MB Hard disk not installed Hard disk installed Network Expansion kit not installed Network Expansion kit installed PS expansion kit not installed PS expansion kit installed FAX expansion kit not installed FAX expansion kit installed Network scanner expansion kit not installed Network scanner expansion kit installed FAX expansion memory not installed FAX expansion memory installed Finish stamp unit not installed Finish stamp unit installed Data security kit not installed Data security kit installed Internet FAX expansion kit not installed Internet FAX expansion kit installed

SIMULATION 22-10 SYSTEM INFORMATION. MACHINE:******* FINISHER: ******* PUNCH: ****** LCC: ******* INSERTER: ******** SYSTEM MEMORY: **MB HDD: ***MB NIC: ******* NSCN: ****** PS3: ****** FAX: ******* FAX MEMORY: **MB STAMP: ******* PCU TYPE: ******* I-FAX *******

Purpose

Adjustment/Setup/Operation data output /Check (Display/Print)

Function (Purpose)

Used to check the use frequency (send/ receive) of FAX. (Only when FAX is installed)

Section

FAX

Operation/Procedure The values of the FAX send counter and the FAX receive counter are displayed. FAX SEND FAX RECEIVE FAX OUTPUT SEND IMAGES SEND TIME RECEIVE TIME

Number of FAX send Number of FAX receive Number of FAX print Page number of send Send time Receive time

SIMULATION 22-11 FAX COUNTER DATA DISPLAY. FAX SEND: ******** FAX RECEIVE : ******** FAX OUTPUT:******** SEND IMAGES: ******** SEND TIME: ********:**:** RECEIVE TIME: ********:**:**

22-12 Purpose

Adjustment/Setup/Operation data output /Check (Display/Print)

Function (Purpose)

Used to check the SPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.)

Section

DSPF

Operation/Procedure The history of paper jam and misfeed is displayed. The misfeed history is displayed sequentially from the latest one. The max. 20 items are recorded. (The oldest one is sequentially deleted.) This data can be used to identify the trouble position. (Jam cause code) Code NO_JAM_CAUSE SPPD1_N SPPD1_S SPPD2_N SPPD2_S SPPD3_N SPPD3_S SPPD4_N SPPD4_S SPOD_N SPOD_S SPSD_SCN

Description No jam. Also used to cancel a jam. SPPD1 not-reached jam SPPD1 remaining jam SPPD2 not-reached jam SPPD2 remaining jam SPPD3 not-reached jam SPPD3 remaining jam SPPD4 not-reached jam SPPD4 remaining jam SPOD not-reached jam SPOD remaining jam Exposure start notification timer end

SIMULATION 22-12 SPF JAM HISTORY. *******,*******,*******,*******,*******,*******,*******,*******,*******,******* *******,*******,*******,*******,*******,*******,*******,*******,*******,*******

(10 lines, 80 digits = 800 characters)

MX-M700N SIMULATION 7 – 21

22-13

22-30

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the operating time of the process section (OPC drum, DV unit, toner bottle).

Section

—

The rotating time and the print quantity of the process section (OPC drum, DV unit (developer), toner motor (toner bottle)) are displayed. OPC drum

TONER

Toner motor

DEVE

DV unit

SIMULATION 22-13 PROCESS DATA DISPLAY. DRUM: ********(counts) TONER: ********(counts) DEVE: *********(counts)

Setting value display/Check

Function (Purpose)

OSA vendor ID display (Application Communication Module)

Section

—

Operation/Procedure When the product key for OSA (Application Communication Module) is effective, vendor ID is displayed. (MAX.: 8 code)

Operation/Procedure

DRUM

Purpose

* APPLICATION NAME: Application name (Max.36 characters) * VENDOR ID: Vendor ID (10 digits)

Count value (counts) Rotating time (sec) Count value (counts) Rotating time (sec) Count value (counts) Rotating time (sec)

**********(sec.) **********(sec.) **********(sec.)

SIMULATION 22-30 OSA VENDOR DISPLAY(APPLICATION COMMUNICATION) APPLICATION NAME VENDOR ID ******************* ********** ******************* ********** ******************* ********** ******************* ********** ******************* ********** ******************* ********** ******************* ********** ******************* **********

22-31

22-19

Purpose

Setting value display/Check

Function (Purpose)

OSA vendor ID display (External module)

Section

—

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Operation/Procedure

Function (Purpose)

Used to check the values of the counters related to the scan mode and the internet FAX mode.

* APPLICATION NAME: Application name (Max.36 characters)

Section

When the product key for OSA (external kit) is effective, vendor ID is displayed. (MAX.: 1 code) * VENDOR ID: Vendor ID (10 digits)

Scanner

Operation/Procedure

SIMULATION 22-31 OSA VENDOR DISPLAY(EXTERNAL ) APPLICATION NAME VENDOR ID ******************* **********

The values of the counters related to the scan mode and the internet FAX mode are displayed. NETWORK SCANNER ORIGINAL COUNTER MAIL COUNTER FTP COUNTER SMB COUNTER INTERNET-FAX ORIGINAL COUNTER INTERNET-FAX SEND INTERNET-FAX RECEIVE INTERNET-FAX OUTPUT SCAN TO HDD INTERNET-FAX SEND IMAGES SCAN SEND IMAGES

Document scan quantity (OC, SPF total quantity) Number of mail send Number of FTP send Number of SMB send Document scan quantity (OC, SPF total quantity) Number of internet FAX send Number of internet FAX receive Internet FAX print quantity Scan to HDD record quantity Number of internet FAX sending page Number of scan sending page

SIMULATION 22-19 NETWORK SCANNER AND INTERNET-FAX COUNTER DISPLAY. NETWORK SCANNER ORIGINAL COUNTER: ********* MAIL COUNTER: ******** FTP COUNTER: ******** INTERNET-FAX ORIGINAL COUNTER: ******** INTERNET-FAX SEND: ******** INTERNET-FAX RECEIVE: ******** INTERNET-FAX OUTPUT: ******** SMB COUNTER: ******** SCAN TO HDD : ******** INTERNET-FAX SEND IMAGES: ******** SCAN SEND IMAGES: ********

23 23-2 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the trouble history of paper jam and misfeed. (If the number of misfeed and troubles is considerably great, it may be judged as necessary to repair.)

Section

—

Operation/Procedure 1)

Select "1. PRINT START.

2)

Press the [START] key.

The trouble history of paper jam and misfeed is printed. This data can be cleared by SIM 24-1.

MX-M700N SIMULATION 7 – 22

SIMULATION 23-2 JAM/TROUBLE DATA PRINT MODE㧚SELECT SETTING,˴AND PRESS START. 0. TRAY SELECT 㧦AUTO ONLY˴ 1. PRINT START

1

24 24-1 Purpose

Data clear

Function (Purpose)

Used to clear the misfeed counter, the misfeed history, the trouble counter, and the trouble history. (The counters are cleared after completion of maintenance.)

Section

—

23-80 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the sensors and detectors in the paper feed and transport section.

Section

Paper feed, paper transport

Operation/Procedure 1)

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key. The confirmation to clear is opened.

Select "2. PRINT PATTERN." with 10-key.

2)

3)

Press the [START] key.

3)

Select "1" (Paper transport time data) with 10-key.

4)

Press the [START] key.

NO: Not clear

The list of the ON time of the sensors and the detectors of the paper transport section is printed.

4)

1

TRAY SELECT AUTO ONLY PRINT START

2

PRINT PATTERN

Transport route section PFD2 On PPD On POD1 On POD2 On TOP TRAY AINPD On FINISHER APPD1 On APPD2 On APPD2 On PFD2 On APPD2 On M1PFD On PFD2 On PFD2 On M2PFD On M1PFD On MPRD1 On MPRD2 On MPRD2 On PPD On MPFD1 On MPFD2 On MPRD1 On LPPD On MPFD2 On

Reference value (ms) [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms] [–––– ms]

Previous value (ms) –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms, –––– ms,

Number of paper jams Number of SPF jams Number of troubles

SIMULATION 24-1 JAM/ TROUBLE COUNTER DATA CLEAR. SELECT1-3, AND PRESS START. 1. PAPER JAM 2. SPF JAM 3. TROUBLE

Print execution. Print of the set data is executed. Print pattern 1. Paper transport time data

1

→ → → → → → → → → → → → → → → → → → → → → → → → → →

PAPER JAM SPF JAM TROUBLE

Auto only (No selection allowed)

SIMULATION 23-80 DATA PRINT MODE. SELECT SETTING, AND PRESS START. 0. TRAY SELECT :AUTO ONLY 1. PRINT START 2. PRINT PATTERN:1

TRAY1 PFD2 On RRC On POD1 On POD2 On Switch Back AINPD On AINPD On APPD1 On Restart Restart (ADU) TRAY3 M1PFD On Restart (TRAY) TRAY4 M2PFD On TRAY2 MPRD1 On Restart MPRD2 On BY MPFD1 On MPFD2 On SIDE LCC LPPD On

Press the [START] key. 1 2 3

When a paper jam or misfeed is generated, the ON time of each sensor and detector is checked to check if the operation of the sensor and the detector, paper feed, and transport are normal or not. 0

Select Yes/NO of counter clear with 10-key. YES: Clear

1

24-2 Purpose

Data clear

Function (Purpose)

Used to clear the number of use (the number of prints) of each paper feed section.

Section

Paper feed

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key. The confirmation to clear is opened.

3)

Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear

4)

Press the [START] key. 1 2 3 4 5 6 7

TRAY1 TRAY2 TRAY3 TRAY4 BPT ADU LCC

SIMULATION PAPER FEED START. 1. TRAY1 3. TRAY3 5. BPT 7. LCC

MX-M700N SIMULATION 7 – 23

Tray 1 use quantity Tray 2 use quantity Tray 3 use quantity Tray 4 use quantity Manual feed tray use quantity Duplex paper feed quantity Side LCC use quantity

24-2 COUNTER DATA CLEAR. SELECT1-7, AND PRESS 2. TRAY2 4. TRAY4 6. ADU

1

24-5

24-3

Data clear

Purpose

Data clear

Purpose

Function (Purpose)

Used to clear the number of use of the finisher, SPF, and the scan (reading) unit.

Function (Purpose)

Section

—

Used to reset the developer counter. (The developer counter of the DV unit which is installed is reset.)

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

Operation/Procedure

The confirmation to clear is opened. 3)

1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

Select Yes/NO of counter clear with 10-key.

The confirmation to clear is opened.

YES: Clear

3)

Select Yes/NO of counter clear with 10-key.

NO: Not clear 4)

YES: Clear

Press the [START] key. 1 2 3 4 5 6

SPF SCAN STAPLER PUNCH STAMP SADDLE STAPLER INSERTER INSERTER OFF LINE

7 8

NO: Not clear 4)

SPF paper quantity Number of times of document scan Number of times of staple Number of times of punch Number of times of SPF finish stamp Number of times of saddle staple

Press the [START] key. 1

DV CARTRIDGE

Developer cartridge counter

SIMULATION 24-5 DEVELOPER COUNTER DATA CLEAR. PRESS START. 1. DV CARTRIDGE

Number of times of inserter Number of inserter off-line times

1

SIMULATION 24-3 ORG./STAPLE COUNTER DATA CLEAR. SELECT1-8, AND PRESS START. 1. SPF 2. SCAN 3. STAPLER 4. PUNCH 5. STAMP 6. SADDLE STAPLER 7. INSERTER 8. INSERTER OFF LINE

1

24-6 Purpose

Data clear

Function (Purpose)

Used to reset the copy counter.

Section

—

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key. The confirmation to clear is opened.

3)

Select Yes/NO of counter clear with 10-key. YES: Clear

24-4

NO: Not clear

Purpose

Data clear

Function (Purpose)

Used to reset the maintenance counter.

Section

—

4)

Press the [START] key. 1

COPY

Copy effective paper counter

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

SIMULATION 24-6 COPY COUNTER DATA CLEAR. PRESS START. 1. COPY

The confirmation to clear is opened. 3)

1

Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear

4)

24-7

Press the [START] key. 1 2

MAINTENANCE F WEB SEND

Maintenance counter Fusing web cleaning feed counter

SIMULATION 24-4 MAINTENANCE COUNTER DATA CLEAR. SELECT1-2, AND PRESS START. 1. MAINTENANCE 2. F WEB SEND

1

Purpose

Data clear

Function (Purpose)

Used to clear the OPC drum counter. (Perform this simulation when the OPC drum is replaced.)

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key. The confirmation to clear is opened.

3)

Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear

4)

Press the [START] key.

MX-M700N SIMULATION 7 – 24

After replacing the OPC drum, be sure to clear the OPC drum counter. 1

DRUM

OPC drum counter

SIMULATION 24-7 DRUM COUNTER DATA CLEAR. SELECT1, AND PRESS START. 1. DRUM

1

24-11 Purpose

Data clear

Function (Purpose)

Used to reset the OPC drum rotation time, and the DV unit rotation time counter. The developer counter in the DV unit installed is reset.

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

24-9

The confirmation to clear is opened.

Purpose

Data clear

Function (Purpose)

Used clear the printer mode print counter and the self print mode print counter.

Section

Printer

3)

Select Yes/NO of counter clear with 10-key. YES: Clear NO: Not clear

4)

Press the [START] key.

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

1 2

DRUM ROTATION DV ROTATION

OPC drum rotation time DV unit rotation time

The confirmation to clear is opened. 3)

SIMULATION 24-11 TIMER DATA CLEAR. SELECT1-2, AND PRESS START. 1. DRUM ROTATION 2. DV ROTATION

Select Yes/NO of counter clear with 10-key. YES: Clear

1

NO: Not clear 4)

Press the [START] key. 1 2

PRINTER OTHERS

Printer counter (Print mode) Other effective paper counter (Self print mode)

SIMULATION 24-9 PRINTER/OTHERS COUNTER DATA CLEAR. SELECT1-2, AND PRESS START. 1. PRINTER 2. OTHERS

1

24-15 Purpose

Data clear

Function (Purpose)

Used to clear the counters related to the scan mode and the internet FAX mode.

Section

—

Operation/Procedure 1)

Select the counter to be cleared with 10-key.

2)

Press the [START] key. The confirmation to clear is opened.

24-10 Purpose Function (Purpose) Section

3)

Data clear Used to clear the FAX counter. (Only when FAX is installed) FAX

Select the counter to be cleared with 10-key.

2)

Press the [START] key.

2 3 4

The confirmation to clear is opened. Select Yes/NO of counter clear with 10-key. YES: Clear

5 6 7 8 9 10

NO: Not clear Press the [START] key. 1 2 3 4 5 6

FAX SEND FAX RECEIVE FAX OUTPUT SEND IMAGES SEND TIME RECEIVE TIME

Press the [START] key. 1

1)

4)

NO: Not clear 4)

Operation/Procedure

3)

Select Yes/NO of counter clear with 10-key. YES: Clear

Number of FAX send Number of FAX receive Number of FAX print Number of sending sheets Send time Receive time

11 12

NETWORK SCANNER ORIGINAL COUNTER MAIL COUNTER FTP COUNTER INTERNET-FAX ORIGINAL COUNTER INTERNET-FAX SEND INTERNET-FAX RECEIVE INTERNET-FAX OUTPUT SMB COUNTER SCAN TO HDD INTERNET-FAX SEND IMAGES SCAN SEND IMAGES DOC FILING OUTPUT

SIMULATION 24-10 FAX COUNTER DATA CLEAR. SELECT1-6, AND PRESS START. 1. FAX SEND 2. FAX RECEIVED 3. FAX OUTPUT 4. SEND IMAGES 5. SEND TIME 6. RECEIVE TIME

1

MX-M700N SIMULATION 7 – 25

Document scan quantity counter in the network scanner mode Number of mail send Number of FTP send Internet FAX document scan quantity (Total quantity of OC and SPF) Number of internet FAX send Number of internet FAX receive Internet FAX print quantity Number of SMB sending Scan to HDD record quantity Number of internet FAX sending page Number of scan sending page Document filing print counter

SIMULATION 24-15 NETWORK SCANNER AND INTERNET-FAX COUNTER CLEAR. SELECT1-12, AND PRESS START. 1. NETWORK SCANNER ORIGINAL COUNTER 2. MAIL COUNTER 3. FTP COUNTER 4. INTERNET-FAX ORIGINAL COUNTER: ******** 5. INTERNET-FAX SEND: ******** 6. INTERNET-FAX RECEIVE: ******** 7. INTERNET-FAX OUTPUT: ******** 8. SMB COUNTER 9. SCAN TO HDD: ******** 10. INTERNET-FAX SEND IMAGES: ******** 11. SCAN SEND IMAGES: ******** 12. DOC FILING OUTPUT: ********

SIMULATION 25-2 AUTOMATIC DV ADJUSTMENT. PRESS START. HUMIDITY AREA : 70.0 - 72.5 DEVE REFERENCE : 114

1

26 26-2 Purpose

Setting

Function (Purpose)

Used to set the paper size of the large capacity tray (LCC) and the paper feed tray 2. (When the paper size is changed, this simulation must be executed to change the paper size in software.)

Section

Paper feed

25 25-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the developing section (toner concentration, humidity and toner concentration sensor, humidity sensor).

Section

Process (Developing section)

Operation/Procedure 1)

Operation/Procedure 1)

Select the number corresponding to the paper feed unit for setting the paper size with 10-key.

2)

Press the [START] key.

3)

Select the number corresponding to the paper size.

4)

Press the [START] key.

Press the [START] key.

1 2

The developing motor and the OPC drum motor rotate, and the toner concentration detection level and the humidity sensor detection level are displayed. SIMULATION 25-1 TONER SENSOR OUTPUT MONITOR. PRESS START. HUMIDITY AREA : 70.0 - 72.5 DEVE REFERENCE : 128

25-2

1

26-3 Setting

Function (Purpose)

Used to make the initial setting of toner concentration when replacing developer.

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure

Purpose

Setting

Function (Purpose)

Used to set the specifications of the auditor. Setting must be made according to the auditor use conditions.

Section

Auditor

Operation/Procedure

Press [START] key. The developing motor rotates for 3 min and the toner concentration sensor makes sampling of toner concentration to display the detection level. After the developing motor stops, the average value of toner concentration sampling is set as the reference toner concentration level. * CAUTION: When the above operation is interrupted on the way, the reference toner concentration level is not set. Also when error code of EE-EL or EE-EU is displayed, the reference toner concentration level is not set normally. (Default: 114)

2)

TRAY 2 size (0 = 8.5 x 11, 1 = A4, 2 = B5) Side LCC size (0 = 8.5 x 11, 1 = A4, 2 = B5) A3 Side LCC size (0 = 8.5 x 11, 1 = A4, 2 = B5, 3 = 11 x 17, 4 = 8.5 x 14, 5 = 8.5 x 11R, 6 = A3, 7 = B4, 8 = A4R)

SIMULATION 26-2 SIZE SETUP. SELECT NUMBER, AND PRESS START. 1. TRAY2 1 2. LCC 1

Purpose

1)

TRAY 2 LCC

The humidity near the developing tank at the developing adjustment is ed.

1)

Select the number corresponding to the auditor mode with 10key.

2)

Press the [START] key. 1 2 3 4 5

P10 VENDOR OTHERS VENDOR-EX VENDOR-EX +

6

VENDOR-EX (MULTI JOB) VENDOR-EX + (MULTI JOB)

7

(Default: 1)

MX-M700N SIMULATION 7 – 26

Built-in auditor mode Coin vendor mode Others Coin vendor mode (No temporary charge) Coin vendor mode (No temporary charge) + Document filing enable Coin vendor mode (No temporary charge) + (JOB queueing) Coin vendor mode (No temporary charge) + Document filing enable + (JOB queueing)

SIMULATION 26-3 AUDITOR SETUP. SELECT 1-3, AND PRESS START. 1. P10 2. VENDOR 3. OTHERS 4. VENDOR-EX 5. VENDOR-EX + 6. VENDOR-EX (MULTI JOB) 7. VENDOR-EX +(MULTI JOB)

SIMULATION 26-6 DESTINATION SETUP. SELECT 1-10, AND PRESS START. 1.USA 2.CANADA 3.INCH 4.JAPAN 5.AB_B 6.EUROPE 7.UK 8.AUSTRALIA 9.AB_A 10.CHINA

1

1

26-10

26-5

Purpose

Setting

Function (Purpose)

Used to set the network scanner trial mode.

Purpose

Setting

Section

—

Function (Purpose)

Used to set the count mode of the total counter and the maintenance counter.

Operation/Procedure

Section

—

1)

Select START/END of the network scanner trial mode with 10key.

Operation/Procedure

2)

Press the [START] key.

1)

Select the number corresponding to the counter to be set with 10-key.

Max. 500 images can be scanned.

2)

Press the [START] key.

3)

Select the count mode with 10-key.

4)

Press the [START] key.

0 1

END START

Trial mode cancel Trial mode start

(Default: 0)

Set the count-up (1 or 2) for A3/11x17 paper. (Select the target counter.) 1 2

TOTAL COUNTER MAINTENANCE (DRUM) COUNTER DV COUNTER

3

SIMULATION 26-10 NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS START. 0.END 1.START

Total counter Maintenance counter/ OPC drum counter

1

Developer counter

(Count-up) 1 2

1 COUNT UP 2 COUNT UP

1 count-up 2 count-up

26-18 Default

Purpose

Setting

Function (Purpose)

Used to set YES/NO of toner save operation. (This function is valid only in Japan and UK versions. (Depends on the destination setting of SIM26-6.) For the other destinations, the same setting can be made by the program P22.)

Section

—

SIMULATION 26-5 A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-3, AND PRESS START. 1. TOTAL COUNTER 1 2. MAINTENANCE(DRUM) COUNTER 1 3. DV COUNTER 1

1

Operation/Procedure

26-6 Purpose

Setting

Function (Purpose)

Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination.

Section

—

1)

Select the number corresponding to the destination with 10key.

2)

Press the [START] key.

After completion of setting, the machine is automatically reset. USA CANADA INCH JAPAN AB_B EUROPE UK AUSTRALIA AB_A CHINA

Select YES/NO of the toner save mode with 10-key.

2)

Press the [START] key. 0 1

YES NO

set. not set.

(Default: 1)

Operation/Procedure

1 2 3 4 5 6 7 8 9 10

1)

SIMULATION 26-18 TONER SAVE MODE SETTING. SELECT 0-1, AND PRESS START. 0. YES 1. NO

United States of America Canada Inch series EX Japan AB series B5 Europe UK Australia AB series A5 China

Since this simulation cannot change the Fax destination, use SIM 66-2 to change the FAX destination.

MX-M700N SIMULATION 7 – 27

1

: '07 Feb 15

1

26-30 Setting

Purpose

Setting

Function (Purpose)

Used to set the operation mode conforming to the CE mark (Europe safety standards). (Conforming to soft start when driving the fusing heater lamp.)

Function (Purpose)

Used to set CONTINUE/STOP of printing when maintenance timing is over and the count value reaches 110% of replacement timing (life).

Section

—

Section

Others

Operation/Procedure

Operation/Procedure

1)

Select the number that corresponds to the operation mode with 10-key.

1)

Select the number that corresponds to the operation mode with 10-key.

2)

Press the [START] key.

2)

Press the [START] key.

0 1

1

26-38

Purpose

NO YES

CE mark control NO (Normal operation) CE mark control YES (Heater lamp soft start operation)

(Default: 1 for Europe, Australia, China, 0 for the others)

0

PRINT CONTINUE PRINT STOP

1

Print continue Print stop

(Default: 0) SIMULATION 26-38 LIFE OVER SETTING. SELECT 0-1, AND PRESS START. 0. PRINT CONTINUE 1. PRINT STOP

SIMULATION 26-30 CE MARK CONTROL SETTING. SELECT 0-1, AND PRESS START. 0. NO 1. YES

1

1

26-41 26-35 Purpose

Setting

Function (Purpose)

Used to set whether the same continuous troubles are displayed as one trouble or the series of troubles with SIM 22-4 when the same troubles occur continuously.

Section

Purpose

Setting

Function (Purpose)

Used to set YES/NO of the automatic magnification ratio selection (AMS) in the pamphlet mode.

Section

—

Operation/Procedure 1)

Enter the number corresponding to whether AMS operation is automatically performed or nor in the center binding mode with the 10-key.

2)

Press the [START] key.

—

Operation/Procedure 1)

Select the number that corresponds to the operation mode with 10-key.

2)

Press the [START] key. 0

1

ONCE

ANY

When two or more troubles of a same kind occur continuously, the troubles are displayed as one trouble in the trouble history of SIM22-4. When two or more troubles of a same kind occur continuously, the troubles are displayed in the trouble history of SIM22-4 directly.

0

NO

1

YES

(Default: 0)

1

1

SIMULATION 26-41 PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS START. 0. NO 1. YES

1

(Default: 0)

SIMULATION 26-35 TROUBLE MEMORY MODE SETTING. SELECT 0-1, AND PRESS START. 0. ONCE 1. ANY

AMS/APS selection allowed. (enable AMS manually) AMS is forcibly operated.

26-50 Purpose

Setting

Function (Purpose)

Black-White reverse YES/NO setting

Section

—

Operation/Procedure 1)

Select ENABLE/DISABLE of the B/W reverse mode with 10key.

2)

Press the [START] key. 0 1

DISABLE ENABLE

B/W reverse mode DISABLE B/W reverse mode ENABLE

(Default: 1) * No B/W reverse function for UK. SIMULATION 26-50 B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS START. 0. DISABLE 1. ENABLE

1

MX-M700N SIMULATION 7 – 28

26-52

27

Purpose

Setting

Function (Purpose)

Used to set whether non-print paper (insertion paper, cover paper) (blank image print paper) is counted up or not.

Section

Paper transport (Paper exit/Switchback/Transport)

27-1 Purpose

Setting

Function (Purpose)

Used to set the specifications for operations in case of communication trouble between the host computer and MODEM (machine side). (When communication trouble occurs between the host computer and MODEM, the self diag display (U7-00) is printed and setting for inhibition of print or not is made.)

Section

Communication unit (RIC/MODEM etc.)

Operation/Procedure 1)

Select YES/NO of the non-print paper count-up with 10-key.

2)

Press the [START] key.

Non-print paper means an insert paper (without copying) in the OHP insertion mode, a cover (without copying) in the cover insertion mode, back surface, and white paper in the duplex exit mode (CA, etc.). 0 1

NO (NO COUNT UP) YES (COUNT UP)

Operation/Procedure

No count up Count up

1)

Select the number corresponding to the operation mode with 10-key.

2)

Press the [START] key.

(Default: 0 for Japan and Australia, 1 for the other) The target counters are as follows: • Copies counter

0

YES

1

NO

• Printer counter • Department management counter • Total counter • Valid paper counter

SIMULATION 26-52 BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS START. 0. NO (NO COUNT UP) 1. YES (COUNT UP)

Though a communication trouble occurs between the host computer and the MODEM (machine side), there is no effect on the machine operations. When a communication trouble occurs between the host computer and the MODEM (machine side), the self diag display (U7-00) is displayed and printing is inhibited.

(Default: 0)

1

SIMULATION 27-1 DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START. 0. YES 1. NO

1

26-68 Purpose

Setting

Function (Purpose)

Used to set ENABLE/DISABLE of the CA key cancel function of print stop.

Purpose

Setting

—

Function (Purpose)

Used to enter the machine tag No. (This function allows to check the tag No. of the machine with the host computer.) Communication unit (RIC/MODEM etc.)

Section

27-5

Operation/Procedure 1)

Select ENABLE/DISABLE of the CA key cancel function of print stop with 10-key.

Section

2)

Press the [START] key.

Operation/Procedure

0 1

DISABLE ENABLE (PRINT STOP)

Disable Enable

(Default: 1)

SIMULATION 26-68 CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS START. 0. DISABLE 1. ENABLE (PRINT STOP)

1)

Enter the tag number with 10-key.

2)

Press the [START] key.

SIMULATION 27-5 TAG # SETTING. INPUT VALUE, AND PRESS START. PRESENT: 00010000 NEW: 00009999

0

MX-M700N SIMULATION 7 – 29

M1PED

30

M1SS2

30-1

M1SS4

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of sensors and detectors in other than the paper feed section and the operations of the related circuits.

Section

—

Operation/Procedure The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted. PFD2 PPD PSD POD1 POD2 POD3 DSW_R DSW_L DSW_F DSW_DSK TFSD THPS2 LPPD T1PPD WEB_END

ADU paper feed detection 2 Resist roller front paper detection Drum rear paper detection After-fusing transport detection 1 After-fusing transport detection 2 Paper full detection Manual feed door open detection Cabinet open detection Front cabinet open detection Desk door open detection Toner remaining quantity detection (Motor rotation number count) Transfer belt separation home sensor 2 LCC paper transport detection Tandem tray 1 paper transport sensor Fusing web end detection

Tray 3 paper empty detection Tray 3 rear edge switch 2 Tray 3 rear edge switch 4

Tray 3 size: (The tray 3 detection size M2PFD Tray 4 transport detection M2PED Tray 4 paper empty detection M2SS2 Tray 4 rear edge switch 2 M2SS4 Tray 4 rear edge switch 4

M1SS1 M1SS3 M1SPD

is displayed.) M2LUD M2SS1 M2SS3 M2SPD

Tray 3 rear edge switch 1 Tray 3 rear edge switch 3 Tray 3 paper remaining quantity detection Tray 4 upper limit detection Tray 4 rear edge switch 1 Tray 4 rear edge switch 3 Tray 4 paper remaining quantity detection

Tray 4 size: (The tray 4 detection size is displayed.)

SIMULATION 30-2 TRAY SENSOR CHECK.. TANSET TLUD1 TSPD1 TPED1 TLUD2 TSPD2 MPLD1 MPLD2 MTOP1 MTOP2 MPED MPFD1 MPRD1 MPRD2 (By Tray size: A3) M1PFD M1LUD M1PED M1SS1 M1SS2 M1SS3 M1SPD (Tray3 size: A3) M2PFD M2LUD M2PED M2SS1 M2SS2 M2SS3 M2SPD (Tray4 size: A3)

TPED2 MPFD2

M1SS4

M2SS4

40 SIMULATION 30-1 SENSOR CHECK.. PFD2 PPD POD2 POD3 DSW_F DSW_DSK LPPD T1PPD

40-1 PSD DSW_R TFSD WEB_END

POD1 DSW_L THPS2

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the manual feed tray paper size detector and the related circuit. (The operation of the manual feed tray paper size detector can be monitored with the LCD display.)

Section

Paper feed

30-2 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of sensors and detectors in the paper feed section and the related circuits.

Section

Paper feed

The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted.

TSPD1 TLUD2

Tray 1 and 2 insertion detection Tray 1 remaining quantity sensor Tray 2 upper limit sensor Tray 2 paper sensor

The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted. The paper width size detection level is displayed.

Operation/Procedure

TANSET

Operation/Procedure

TLUD1 TPED1 TSPD2

Tray 1 upper limit sensor Tray 1 paper sensor

Tray 2 remaining quantity sensor TPED2 MPLD1 Manual tray length detection 1 MTOP1 Manual tray pull-out MPLD2 Manual tray length detection 2 detection 1 MTOP2 Manual tray pull-out MPED Manual feed paper detection 2 empty detection 2 MPFD1 Detection 1 of paper MPFD2 Detection 2 of from manual paper from paper feed manual paper feed MPRD1 Manual relay paper MPRD2 Manual relay paper detection 1 detection 2 By Tray size: (The manual feed tray detection size is displayed.) M1PFD Tray 3 transport M1LUD Tray 3 upper limit detection detection

MPLD1 MPLD2 MTOP1 MTOP2 BY_WIDTH BY_AD By Tray width size

Manual tray length detection 1 Manual tray length detection 2 Manual tray pull-out detection 1 Manual tray pull-out detection 2 anual feed guide plate position Manual feed width detection volume output AD value (Manual tray detection size is displayed.) A4/A3, 11 x, B5/B4, 8.5 x , A4R, B5R, A5R, 5.5x, 7.25x, EXTRA

SIMULATION 40-1 BY TRAY SENSOR CHECK.. MPLD1 MPLD2 MTOP1 MTOP2 BY_WIDTH: 2100 BY_AD: 600 (By Tray width size: A4/A3)

MX-M700N SIMULATION 7 – 30

40-11

40-2 Purpose

Adjustment

Purpose

Operation test/Check

Function (Purpose)

Used to adjust the manual paper feed tray paper width detector detection level.

Function (Purpose)

Used to check the multi-purpose tray width detection adjustment value.

Section

Paper feed

Section

Paper feed

Operation/Procedure

Operation/Procedure

1)

Open the manual paper feed guide to the maximum width position.

The sensor and detector operation conditions are displayed.

2)

Select MAX. POSITION with 10-key.

3)

Press the [START] key. The max. width detection level is recognized.

4)

Press the [SYSTEM SETTINGS] key.

5)

Set the manual paper feed guide to the width for the A4R size.

6)

Select POSITION 1 with 10-key.

7)

Press the [START] key.

8)

Press the [SYSTEM SETTINGS] key.

9)

Set the manual paper feed guide to A5R size width.

The active sensors and detectors are highlighted. The paper width detection level is also displayed. M1SS1 M1SS2 M1SS3 M1SS4 TRAY3_WIDTH TRAY3_AD Tray3 width size

The A4R width detection level is recognized.

Tray 3 size detection 1 Tray 3 size detection 2 Tray 3 size detection 3 Tray 3 size detection 4 Tray 3 guide plate position Tray 3 width detection volume output AD value (Tray 3 width direction detection size is displayed.) A4/A3, 11X, B5/B4, 8.5X, A4R, B5R, A5R, 5.5X, 7.25X, EXTRA

SIMULATION 40-11 TRAY3 SENSOR CHECK..

10) Select POSITION 2 with 10-key. 11) Press the [START] key.

M1SS1 M1SS2 M1SS3 M1SS4 TRAY3_WIDTH: 2100 TRAY3_AD: 600 (Tray3 width size: A4/A3)

The A5R width detection level is recognized. 12) Press the [SYSTEM SETTINGS] key. 13) Open the manual paper feed guide to the minimum width position. 14) Select MIN. POSITION with 10-key. 40-12

15) Press the [START] key. The minimum width detection level is recognized. When each of the above operations has been completed, the "COMPLETE" message appears; when any of the operations has failed, the "ERROR" message appears.

Purpose

Adjustment/Setup

Function (Purpose)

Used to check the multi-purpose tray width detection adjustment value.

Section

Paper feed

Operation/Procedure SIMULATION 40-2 BY TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1. MAX. POSITION 2. POSITION 1 3. POSITION 2 4. MIN. POSITION

1

40-7 Purpose

Adjustment/Setup

Function (Purpose)

Used to enter the manual paper feed tray paper width adjustment value.

Section

Paper feed

1)

Select the number corresponding to the set item with 10-key.

2)

Press the [START] key.

3)

Enter the set value with 10-key.

4)

Press the [START] key. MAX. POSITION POSITION 1 POSITION 2 MIN. POSITION

Open the paper feed tray 3 paper feed guide to the max. width position.

2)

Select MAX. POSITION with 10-key.

3)

Press the [START] key.

4)

Press the [SYSTEM SETTINGS] key.

5)

Open the paper feed tray 3 paper feed guide to the min. width position.

6)

Select MIN. POSITION with 10-key.

The max. width detection level is recognized.

7)

Press the [START] key. The minimum width detection level is recognized.

If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.

Operation/Procedure

1 2 3 4

1)

SIMULATION 40-12 TRAY3 ADJUSTMENT. SELECT 1-2, AND PRESS START. 1. MAX. POSITION 2. MIN. POSITION

Max. position Adjustment point 1 Adjustment point 2 Min. position

SIMULATION 40-7 BY TRAY VALUE SETTING. SELECT 1-4, AND PRESS START. 1. MAX. POSITION : 72 2. POSITION 1 : 380 3. POSITION 2 : 710 4. MIN. POSITION : 804

1

MX-M700N SIMULATION 7 – 31

1

: '07 Feb 15

1

41-3

41 41-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the document size sensor and the related circuit. (The operation of the document size sensor can be monitored with the LCD display.)

Section

Others

Operation/Procedure The sensor and detector operation conditions are displayed. The active sensors and detectors are highlighted. OCSW

Document cover status

PD1 - 7

Document detection sensor status

SIMULATION 41-1 PD SENSOR CHECK.. OCSW PD1 PD2 PD3

PD4

PD5

PD6

Open: Normal display Close: Highlighted No document: Normal display Document present: Highlighted

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the document size sensor and the related circuit. (The document size sensor output level can be monitored with the LCD display.)

Section

Others

Operation/Procedure The detection output level (A/D value) of the document sensors (PD1 - PD7) is displayed in real time. * The value in [ ] on the side of each sensor name indicates the threshold value. The light receiving value (A/D value) and the threshold value (A/D value) of PD1 - PD7 are in the range of 1 - 255. The default of threshold value is 128. OCSW PD1 - 7

Original cover status

Open: Normal display Close: Highlighted PD sensor detection level The value in [ ] indicates the adjustment threshold value (SIM41-2 adjustment value).

SIMULATION 41-3 PD SENSOR DATA DISPLAY. OCSW PD1[128]: 200 PD2[128]: 200 PD3[128]: 50 PD4[128]: 52 PD5[128]: 51 PD6[128]: 50 PD7[128]: 52

PD7

41-2 Purpose

Adjustment

Function (Purpose)

Used to adjust the document size sensor sensing level.

Section

Others

43 43-1

Operation/Procedure 1)

Open the original cover. With nothing placed on the original table, select NO ORIGINAL with 10-key.

2)

Press the [START] key. The sensor level is set without document on the document table.

Purpose

Setting

Function (Purpose)

Used to set the fusing temperature in each operation mode.

Section

Fusing

Operation/Procedure

3)

Place an A3 (11x17) document on the document table, and select A3 ORIGINAL with 10-key.

1)

4)

Press the [START] key.

2)

Press the [START] key.

The sensor level is set when detection the document.

3)

Enter the setting value with 10-key.

If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.

4)

Press the [START] key.

SIMULATION 41-2 PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START. (PLEASE OPEN THE ORIGINAL COVER.) 1. NO ORIGINAL 2. A3 ORIGINAL

1

Select the number corresponding to the setting mode with 10key.

1

INSIDE NORMAL

2

5

OUTSIDE NORMAL INSIDE PREHEAT OUTSIDE PREHEAT LEFT NORMAL

6

LEFT PREHEAT

3 4

Fusing roller inside/ normal mode Fusing roller outside/ normal mode Fusing roller inside/ preheat mode Fusing roller outside/ preheat mode Sub-heat roller/normal mode Sub-heat roller/ preheat mode

100V 200

200V 205

170

170

200

205

170

170

SIMULATION 43-1 F TEMPERATURE SET. SELECT 1-6, AND PRESS START. 1. INSIDE NORMAL 185 5. LEFT NORMAL 185 2. OUTSIDE NORMAL 185 6. LEFT PREHEAT 140 3. INSIDE PREHEAT 140 4. OUTSIDE PREHEAT 140

1

MX-M700N SIMULATION 7 – 32

1

: '07 Feb 15

1

43-3 BIT6

Purpose

Setting (Adjustment)

Function (Purpose)

Fusing motor RPM setting.

Section

Setting

BIT7

Operation/Procedure

Item Toner concentration correction C

OPC drum for environment correction

1

1)

Select the number corresponding to the adjustment item with 10-key.

NOTE: Set to 222.

2)

Press the [START] key.

When bit=1, correction is made.

3)

Enter the setting (adjustment) value with 10-key.

4)

Press the [START] key.

Unless special measures are required, do not change the setting values below. 1

Item 1 2

NORMAL SLOWDOWN

Setting range 0 - 99 0 - 99

Default 55/62 70 (ppm) (ppm) 34 34 46 44

Default 1

Toner concentration correction in low density image continuous print

Bit

15 0

Bit

6 Tcon_C

14 0

13 0

12 0

5 Tcon_B

11 0

4 Tcon_A

10 0 3 Humidity

9 0

8 0

2 Pcon_lm

7 Env 1 Drum

SIMULATION 44-1 PROCESS CORRECTION VALUE SETTING. INPUT VALUE 0-999 AND PRESS START. BIT1: DRUM BIT2: PROCON_LM BIT3: HUMIDITY BIT4: TONERCON_A BIT5: TONERCON_B BIT6: TONERCON_C BIT7: ENVIRONMENT

223

SIMULATION 43-3 F MOTOR SPEED SETTING. SELECT 1-2, AND PRESS START. 1. NORMAL 36 2. SLOWDOWN 50

1

NOTE: BIT0 is not displayed, but set to the developing bias correction function. This setting is forcibly made enable, and cannot be disabled. 44-2

44

Purpose

Adjustment

Function (Purpose)

Used to perform the gain adjustment (image density sensor LED current adjustment) of the image density sensor and the gain adjustment (OPC drum marking sensor LED current adjustment) of the OPC drum marking sensor.

Section

Image process (Photoconductor)

44-1 Purpose

Setting

Function (Purpose)

Used to set enable/disable of correction operations in the image forming (process) section.

Section

Image process (Photoconductor/Developing/Transfer/Cleaning)

Operation/Procedure 1)

Each bit (7 kinds) is assigned to each correction item to set ENABLE/DISABLE of the operation. Each bit is assigned with 0 or 1 value. Enter the total values of items which are desired to be valid with the 10-key.

2)

Press the [START] key.

BIT1

BIT2

BIT3 BIT4

BIT5

Item OPC drum membrane decrease (sensitivity/ potential) correction The range of the toner patch making voltage in the developing bias voltage/main charger grid voltage correction is specified. (Voltage limit) For humidity correction Toner concentration correction A

Toner concentration correction B

Laser power/main charger grid voltage

Default 1

Developing bias/main grid voltage (adjusted by SIM 8-1 and 8-2) +100v

1

Toner concentration correction When the developing bias/main charger grid voltage correction is changed more than the specified level, the toner concentration control level is corrected. Correction for the developer life

1

Operation/Procedure Press [START] key, and the adjustment is automatically performed. When the adjustment is completed, the adjustment result is displayed. If the adjustment is not completed normally, "ERROR" is displayed. When an error occurs, the adjustment result is not revised. DMLED PCLED DRUM

Drum marking sensor gain adjustment value Image density sensor gain adjustment value Kind of the drum 0 = Other/1 = SHARP drum

SIMULATION 44-2 PROCON GAIN ADJUSTMENT. PRESS START. DMLED: 0 PCLED: 0 DRUM : 0

1

0

MX-M700N SIMULATION 7 – 33

: '07 Feb 15

1

44-4 Purpose

Setting

Function (Purpose)

Used to set the target density level in the image density correction.

Section

Image process (Photoconductor/Developing)

DEVE MIXING TIME DRUM GR BS

Operation/Procedure 1)

Enter the target density level in the image density correction with 10-key.

2)

Press the [START] key.

DV BS

(Default: 32) LD ADJ SIMULATION 44-4 PROCON INITIAL DENSITY SETUP. PRESS START. 1.PROCON INI DENSITY 32

1 44-5 Purpose

Setting

Function (Purpose)

Used to set the reference developing bias voltage, the reference main charger grid voltage, and the laser power in the image density correction.

Section

Image process (Photoconductor/Developing)

Operation/Procedure

1

1)

Select the number corresponding to the setting mode with 10key.

2)

Press the [START] key.

3)

Enter the setting (adjustment) value with 10-key.

4)

Press the [START] key.

1

GRID BIAS VOL DEVE BIAS VOL LASER POWER

2 3

Item Main charger voltage for developing bias voltage correction Reference developing bias voltage or developing bias voltage correction Reference laser power for developing bias voltage correction

SIMULATION 44-5 PROCESS CONTROL 1.GRID BIAS VOL 2.DEVE BIAS VOL 3.LASER POWER

TEST. SELECT 1-3, AND PRESS START. *** 280 ***

1

AUTO CHARA CHARA P PHOTO PRT DESTINATION 1 DESTINATION 2

Purpose

Adjustment/Setup/Operation data output/ Check (Display)

Function (Purpose)

Used to check the data related to the image forming section correction (process correction) result (corrected main charger grid voltage, the developing bias voltage, and the laser power voltage in each print mode). (This simulation allows to check that correction is performed normally or not.)

Section

LD_ADJ 000/000 000/000 000/000 000/000 000/000

Purpose

Adjustment/Setup/Operation data output/ Check (Display)

Function (Purpose)

Used to display sampling toner image patch density data in image density correction. (Used to check that the correction is performed normally or not.)

Section

Image process (Photoconductor/Developing)

Operation/Procedure

PC LED END DV BS ID (n) PT1/BS1 PT2/BS2 PT3/BS3

Image process (Photoconductor/Developing/Transfer/Cleaning)

Item OPC drum rotation time (sec)

1: 55/62 (ppm) 0: 70 (ppm)

44-12

Operation/Procedure

DRUM ROTATION TIME

NOTE Reset by SIM 24-11.

SIMULATION 44-9 PROCESS CONTROL DATA DISPLAY. DRUM ROTATION TIME: 01234567(sec) DEVE MIXING TIME: 01234567(sec) DRUM: 0 GR_BS DV_BS AUTO 000/000 000/000 CHARA 000/000 000/000 CHARA_P 000/000 000/000 PHOTO 000/000 000/000 PRT 000/000 000/000 DESTINATION1: 0 DESTINATION2: 0

DMLED

44-9

Item Developing roller rotation time (sec) OPC drum identification code Actual main charger grid voltage (including correction) / Main charger grid voltage adjusted with SIM 8-2 Actual developing bias voltage (including correction) / Developing bias voltage adjusted with SIM 8-1 Actual laser power beam (Including correction) Auto copy mode Text copy mode Text/Photo copy mode Photo copy mode Printer mode Toner destination code stored in the main unit Toner destination code stored in the toner bottle CRUM chip

NOTE Reset by SIM 24-11.

MX-M700N SIMULATION 7 – 34

OPC drum marking sensor LED current adjustment value Image density sensor gain adjustment value Developing bias voltage when making PT2/BS2 of ID (1) Indicates the toner patch making procedures. Toner patch density detection level/OPC drum surface detection level when the developing bias is DV - 50V. Toner patch density detection level/OPC drum surface detection level when the developing bias is DV. Toner patch density detection level/OPC drum surface detection level when the developing bias is DV + 50V.

SIMULATION 44-12 DM DATA, PATCH/BASE DATA DISPLAY. DMLED: 000 PC LED: 000 END DV_BS: 000 PT1/BS1 PT2/BS2 PT3/BS3 ID(1): 000/000 000/000 000/000 ID(2): 000/000 000/000 000/000 ID(3): 000/000 000/000 000/000 ID(4): 000/000 000/000 000/000 ID(5): 000/000 000/000 000/000 ID(6): 000/000 000/000 000/000 ID(7): 000/000 000/000 000/000 ID(8): 000/000 000/000 000/000

SIMULATION 44-16 TONER CONTROL STANDARD LEVEL DISPLAY. HUMIDITY AREA: 7 INT HUMIDITY AREA: 7 TARGET LEVEL = DEV REF + HUM(TARGET) + A + B 114 = 114 + 0( 0) + 0 + 0

46 46-2

44-14 Purpose

Adjustment/Setup/Operation data output/ Check (Display)

Function (Purpose)

Used to check the output level of the temperature sensor and the humidity sensor.

Section

Image process (Photoconductor/Developing)

Purpose

Adjustment

Function (Purpose)

Used to adjust the copy density in all the copy modes (Auto, Text, Text/Photo, and Photo mode).

Section

—

Operation/Procedure 1)

Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 6.)

Operation/Procedure The output levels of the temperature sensor and the humidity sensor in the developing unit are displayed. TH-DV (Not used) TH-RA (Not used) TH-CL TH-EX HUS-DV HUS-TC (Not used)

Developing section temperature sensor Room temperature sensor Process section temperature sensor Paper discharging section temperature sensor Developing section humidity sensor Process section humidity sensor

0 - 255 0 - 255

0

TRAY SELECT

1

COPY START

2

EXP LEVEL

3 4 5

AE 3.0 CH 3.0 MIX 3.0

0 - 255 0 - 255 0 - 255

6

4)

PHOTO 3.0

Paper feed tray selection Copy START (Default) Exposure level selection AE mode Text mode 3.0 Text/Photo mode 3.0 Photo mode 3.0

Setting range

Default

0 - 99

50

Press the [P] or [START] key. The adjustment value is set. When [START] key is pressed, copy is performed and the adjustment value is set simultaneously. Check the density of the printed copy image.

Normal display ERROR display

Purpose

Adjustment/Setup/Operation data output/ Check (Display)

Function (Purpose)

Used to check the toner concentration control data.

Section

Process (Developing)

Operation/Procedure

B

Enter the copy density level with 10-key. Item

44-16

HUMIDITY (TARGET) A

Press the [START] key.

3)

0 - 255

SIMULATION 44-14 SENSOR DATA DISPLAY MONITOR. TH-DV: 255 TH-RA: 255 TH-CL: 255 TH-EX: 255 HUS-DV: 255 HUS-TC: 255

HUMIDITY AREA INT HUMIDITY AREA TARGET LEVEL DEV REF

2)

Humidity area

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

NOTE: When the copy image density is adjusted with this simulation, the copy image densities of all the copy modes are changed to the copy image density level set with this simulation. That is, the copy image density of each copy mode set with SIM 46-9, 10, 11 is changed to the copy image density level adjusted with this simulation. To select paper (paper feed tray), perform the following procedures.

Humidity area when setting the toner concentration control level (SIM 25-2) Current toner concentration control level Toner concentration when setting the toner concentration control level (SIM 25-2) Toner concentration correction value for humidity Toner concentration correction value for change in developing bias voltage Toner concentration value for developer life

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

MX-M700N SIMULATION 7 – 35

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

To select exposure mode, perform the following procedures. 1)

Enter 2 with 10-key.

2)

Press [START] key. (The mode is changed to the exposure mode.)

3)

Enter the number corresponding to the exposure level to be used with 10-key, and press [START] key. 3 4 5 6

AE 3.0 CH 3.0 MIX 3.0 PHOTO 3.0

AE mode Text mode 3.0 Text/Photo mode 3.0 Photo mode 3.0

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. SIMULATION 46-9 EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50

SIMULATION 46-2 EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. AE 3.0 50 4. CH 3.0 50 5. MIX 3.0 50 6. PHOTO 3.0 50

1

1

46-10 Purpose

Adjustment

Function (Purpose)

Used to adjust the print density for each density level (display value) in the copy mode (binary - Text mode). An optional print density can be set for each density level (display value).

Used to adjust the print density for each density level (display value) in the copy mode (binary - Text/Photo mode). An optional print density can be set for each density level (display value).

Section

—

—

Operation/Procedure

46-9 Purpose

Adjustment

Function (Purpose)

Section

1)

Operation/Procedure

Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.)

1)

Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.)

2)

Press the [START] key.

2)

Press the [START] key.

3)

Enter the copy density level with 10-key.

3)

Enter the copy density level with 10-key. Item Setting range

Item 0

TRAY SELECT

1

COPY START

2

EXP LEVEL

3 4 5 6 7 8 9 10 11

1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

4)

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

0 - 99

Default

50

0

TRAY SELECT

1 2

COPY START EXP LEVEL

3 4 5 6 7 8 9 10 11

1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

4)

0 - 99

50

Press the [P] or [START] key. When [START] key is pressed, copy is performed and the adjustment value is set simultaneously.

The adjustment value is set.

Check the density of the printed copy image.

When [START] key is pressed, copy is performed and the adjustment value is set simultaneously.

Normal display ERROR display

Check the density of the printed copy image.

Door open Jam Paper empty

Default

The adjustment value is set.

Press the [P] or [START] key.

Normal display ERROR display

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

Setting range

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

MX-M700N SIMULATION 7 – 36

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

SIMULATION 46-11 EXP. LEVEL SETUP (PHOTO2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50

SIMULATION 46-10 EXP. LEVEL SETUP (MIX.2). SELECT 0-11, AND PRESS START. 0. TRAY SELECT 1 1. COPY START 2. EXP LEVEL 1 3. 1.0 50 4. 1.5 50 5. 2.0 50 6. 2.5 50 7. 3.0 50 8. 3.5 50 9. 4.0 50 10. 4.5 50 11. 5.0 50

1

1

46-12 46-11

Purpose

Adjustment

Purpose

Adjustment

Function (Purpose)

Function (Purpose)

Used to adjust the print density for each density level (display value) in the copy mode (binary - Photo mode). An optional print density can be set for each density level (display value).

Used to adjust the print density in the FAX mode (all modes).

Section

—

Operation/Procedure

Section

—

Operation/Procedure 1)

Select the number corresponding to the copy density adjustment level with 10-key. (Select one of 3 - 11.)

2)

Press the [START] key.

3)

Enter the copy density level with 10-key. Item 0

TRAY SELECT

1 2

COPY START EXP LEVEL

3 4 5 6 7 8 9 10 11

1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

4)

Paper feed tray selection Copy START (Default) Exposure level selection Exposure level 1.0 Exposure level 1.5 Exposure level 2.0 Exposure level 2.5 Exposure level 3.0 Exposure level 3.5 Exposure level 4.0 Exposure level 4.5 Exposure level 5.0

Setting range

1)

Select the adjustment item (FAX EXP. LEVEL) with 10-key.

2)

Press the [START] key.

3)

Enter the print density level with 10-key. Item 0

TRAY SELECT

1 2

COPY START FAX EXP. LEVEL

Default

4)

0 - 99

50

Press the [P] or [START] key. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously.

0 - 99

Check the density of printed image.

50

Normal display ERROR display

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

NOTE: When the FAX print image density is adjusted with this simulation, the print image densities of all the FAX modes are changed to the image density level set with this simulation. That is, the print image density of each FAX mode set with SIM 46-13, 14, 15 and 16 is changed to the print image density level adjusted with this simulation.

The adjustment value is set. When [START] key is pressed, copy is performed and the adjustment value is set simultaneously. Check the density of the printed copy image.

Door open Jam Paper empty

Default

The adjustment value is set.

Press the [P] or [START] key.

Normal display ERROR display

Paper feed tray selection Copy START (Default) FAX mode print density

Setting range

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

MX-M700N SIMULATION 7 – 37

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. SIMULATION 46-13 EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50

SIMULATION 46-12 EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.FAX EXP.LEVEL 50

1

1

46-13 Purpose

Adjustment

46-14

Function (Purpose)

Used to adjust the print density in the FAX mode (each Normal text mode). (Only when FAX is installed.)

Purpose

Adjustment

Function (Purpose)

Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.)

Operation/Procedure

Section

—

1)

Operation/Procedure

Section

—

Select the number corresponding to one of the following adjust ment items with 10-key. (Select one of 3 - 14.) * Manual mode (Print density adjustment level)

1)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.)

* Auto mode

* Normal mode (Print density adjustment level)

2)

Press the [START] key.

3)

Enter the print density level with 10-key.

* Normal mode (Print density adjustment level) (Half-tone mode) * Auto mode Setting range

Item 0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3 4 5 6 7 8

AUTO 1.0 2.0 3.0 4.0 5.0

4)

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5

2)

0 - 99

0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3 4 5 6 7 8 9 10

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

11

2.0 (H)

12

3.0 (H)

13

4.0 (H)

14

5.0 (H)

50

The adjustment value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the density of printed image.

Door open Jam Paper empty

Enter the print density level with 10-key. Item

Press the [P] or [START] key.

Normal display ERROR display

* Auto mode (Half-tone mode)

Default

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

3)

Setting range

Default

0 - 99

50

Press the [P] or [START] key. The adjustment value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously. Check the density of printed image.

1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Normal display ERROR display

Door open Jam Paper empty

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures.

When the total of the above set value (1 - 6) and 20 is entered, the mode is changed to the duplex mode.

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

MX-M700N SIMULATION 7 – 38

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

When [START] key is pressed, printing is performed and the adjustment value is set simultaneously.

4)

Press [START] key. (The paper feed tray is selected.)

Check the density of print image.

1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Normal display ERROR display

SIMULATION 46-14 EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50

1

46-15 Purpose

Adjustment

Function (Purpose)

Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.)

Section

—

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) * Normal mode (Print density adjustment level)

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

SIMULATION 46-15 EXP.LEVEL SETUP FAX(SUPER FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50

* Normal mode (Print density adjustment level) (Half-tone mode) * Auto mode * Auto mode (Half-tone mode) Press the [START] key.

3)

Enter the print density level with 10-key. Item 0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3 4 5 6 7 8 9 10

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

11

2.0 (H)

12

3.0 (H)

13

4.0 (H)

14

5.0 (H)

4)

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

1

Operation/Procedure

2)

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures.

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

1)

Door open Jam Paper empty

Setting range

Default

0 - 99

50

Press the [P] or [START] key. The adjustment value is set.

MX-M700N SIMULATION 7 – 39

46-16 Purpose

Adjustment

Function (Purpose)

Used to adjust the print density in the FAX mode (each ultra fine mode). (Only when FAX is installed.)

Section

—

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

SIMULATION 46-16 EXP.LEVEL SETUP FAX(ULTRA FINE).SELECT 0-14,AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.AUTO 50 4.1.0 50 5.2.0 50 6.3.0 50 7.4.0 50 8.5.0 50 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50 12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50

Operation/Procedure 1)

1

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) * Normal mode (Print density adjustment level) * Normal mode (Print density adjustment level) (Half-tone mode) * Auto mode * Auto mode (Half-tone mode)

46-17

2)

Press the [START] key.

Purpose

Setting

3)

Enter the print density level with 10-key.

Function (Purpose)

Used to set the gain in shading correction.

Section

Optical (Image scanning) - CCD, CIS

Item 0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3 4 5 6 7 8 9 10

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

11

2.0 (H)

12

3.0 (H)

13

4.0 (H)

14

5.0 (H)

4)

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range

Default

Operation/Procedure 1)

0 - 99

50

Select the number corresponding to the adjustment item with 10-key.

2)

Press the [START] key.

3)

Enter the shading gain change value with 10-key.

4)

Press the [START] key.

There is normally no need to change the shading gain with this simulation. Only when the scanned image density is unsatisfactory though shading is performed, the above procedure is performed. Item 1 2 3 4 5

Press the [P] or [START] key. The adjustment value is set. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously.

CCD FRONT ODD CCD FRONT EVEN CCD REAR ODD CCD REAR EVEN CIS

Door open Jam Paper empty

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

Default 112

128

SIMULATION 46-17 CCD/CIS SHADING GAIN DATA SETUP. SELECT 1-5, AND PRESS START. 1. CCD FRONT ODD 128 2. CCD FRONT EVEN 128 3. CCD REAR ODD 128 4. CCD REAR EVEN 128 5. CIS 128

Check the density of printed image. Normal display ERROR display

Setting range 0 - 255

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

MX-M700N SIMULATION 7 – 40

(Gamma adjustment) 46-18

After completion of the above procedures, perform the following procedures.

Purpose

Adjustment

Function (Purpose)

Used to adjust the gamma (density gradient) in the copy mode.

Section

1)

Enter the gamma level with 10-key.

2)

Press the [P] or [START] key. When [START] key is pressed, printing is performed and the adjustment value is set simultaneously.

—

Operation/Procedure

Check the gamma density (copy density in the low density area and the high density area) of printed copy image.

(Copy mode selection) 1)

Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 14.)

2)

Press the [START] key.

The greater the adjustment value is, the greater the gamma value is, resulting in a higher contrast. (Copy condition setting in this simulation)

(Print mode selection in the FAX mode)

To select paper (paper feed tray), perform the following procedures.

1)

Enter 2 with 10-key.

2)

Press the [START] key.

3)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 3 - 14.) * Normal mode (Print density adjustment level) * Normal mode (Print density adjustment level) (Half-tone mode)

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

* Auto mode

1 2 3 4 5 6

* Auto mode (Half-tone mode) Setting range

Item 0

TRAY SELECT

1 2 3 4 5 6 7 8 9 10 11 12 13 14

PRINT START EXP LEVEL OC_AE OC_CHARA OC_MIX OC_PHOTO SPF_AE SPF_CHARA SPF_MIX SPF_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO

Paper feed tray selection Print start (Default) Exposure level selection AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF) Text mode (SPF) Text/Photo mode (SPF) Photo mode (SPF) AE mode (CIS) Text mode (CIS) Text/Photo mode (CIS) Photo mode (CIS)

Default

0 - 127

96 64

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. SIMULATION 46-18 GAMMA SETUP(COPIER). SELECT 1-14, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.EXP LEVEL 1 3.OC_AE 64 4.OC_CHARA 5.OC_MIX 64 6.OC_PHOTO 64 7.SPF_AE 64 8.SPF_CHARA 64 9.SPF_MIX 64 10.SPF_PHOTO 64 11.CIS_AE 64 12.CIS_CHARA 64 13.CIS_MIX 64 14.CIS_PHOTO 64

96 64

96 64

46-19 Purpose

Adjustment

Function (Purpose)

Used to set the auto mode operation specifications in each mode (copy, scan, FAX).

Section

—

[AE mode] 3 4 5 6 7 8 9 10 11 12 13 14

4)

AUTO 1 2 3 4 5 AUTO (H) 1.0 (H) 2.0 (H) 3.0 (H) 4.0 (H) 5.0 (H)

Item Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5

Operation/Procedure (Toner save operation YES/NO setting in the auto mode) 1)

Door open Jam Paper empty

Select "1. AE MODE" with 10-key.

2)

Press the [START] key.

3)

Select the number that corresponds to the operation specifications with 10-key.

4)

(Half-tone) (Half-tone) (Half-tone) (Half-tone) (Half-tone)

Press the [START] key. When [START] key is pressed, the adjustment value is set.

(Auto copy mode operation setting) 1)

Press the [START] key.

Normal display ERROR display

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

Select the number corresponding to the mode with 10-key. (Select one of 2 - 4.)

2)

Press the [START] key.

3)

Select the number that corresponds to the operation mode with 10-key.

MX-M700N SIMULATION 7 – 41

4)

Press the [START] key. Item 1 2

AE MODE AE STOP MODE (COPIER) AE STOP MODE (SCANNER) AE STOP MODE (FAX)

3 4

Mode AE mode

Set value 1

2

AE fixed mode

AE fixed OFF:

AE fixed ON:

0 1

AE mode AE fixed mode (Copier)

0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3

SPF (FRONT)

4

SPF (REAR)

5

DSPF

Content Paper feed tray selection 1: TRAY1 2: TRAY2 3: TRAY3 4: TRAY4 5: Manual feed 6: Side LCC Print start (Default) Exposure level selection 3: Exposure level 1.0 4: Exposure level 1.5 5: Exposure level 2.0 6: Exposure level 2.5 7: Exposure level 3.0 8: Exposure level 3.5 9: Exposure level 4.0 10: Exposure level 4.5 11: Exposure level 5.0 SPF (front) (front frame side) SPF (front) (rear frame side) DSPF (Back surface)

AE fixed mode (Scanner) AE fixed mode (FAX)

Item Image quality priority mode (Normal mode) * Gamma is sharp to provide high contrast images. Toner consumption priority mode * Gamma is mild to provide low contrast images. AE fixed OFF AE fixed ON

Default 2

1 (COPIER) 0 (SCANNER /FAX)

The automatic density (exposure) control is performed in real time. (The density level is changed in real time according to the document pattern.) The density at the lead edge of the document is scanned, and the overall density (exposure) level is determined according to the scanned density level. (Overall density level fixed)

Setting range —

Default —

— —

— —

0 - 255

128

• Set value - 128 is added to the shading adjustment value (SIM 46-17).

SIMULATION 46-19 EXP.MODE SETUP. SELECT 1-2, AND PRESS START. 1.AE MODE 1 2.AE STOP MODE(COPIER) 1 3.AE STOP MODE(SCANNER)0 4.AE STOP MODE(FAX) 0

SIMULATION 46-20 OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START. 0. TRAY SELECT 1 1. PRINT START 2. EXP LEVEL 1 3. SPF(FRONT) 128 4. SPF(REAR) 128 5. DSPF 128

1

46-20 Purpose

Adjustment

46-21

Function (Purpose)

Used to adjust the copy density correction in the SPF copy mode for the document table copy mode. The adjustment is made so that the copy density becomes the same as that of the document table copy mode.

Purpose

Adjustment

Function (Purpose)

Used to set the auto mode operation specifications in each mode (copy, scan, FAX).

Section

—

Section

SPF

Operation/Procedure 1)

Operation/Procedure

Select the adjustment item SCANNER EXP. LEVEL with 10key.

(Adjustment mode selection)

2)

Press the [START] key.

1)

3)

Enter the image density adjustment value.

4)

Press the [P] or [START] key.

Select the number that corresponds to the mode for which to make adjustments with 10-key. SPF front frame side (Front surface copy), SPF rear frame side (Front surface copy), SPF (Back surface copy) (Select one of 3 - 5.)

2)

Press the [START] key.

(Copy density level adjustment) 1)

Enter the density correction value with 10-key.

2)

Press the [P] or [START] key.

NOTE: When this simulation is performed to adjust the scan image densities, all the image densities in all the scan modes are changed to the image density level set with this simulation. That is, the image densities set with SIM 46-22, 23, 24, 25, and 45 are changed to the image density level set with this simulation.

(Copy condition setting in this simulation)

Item

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

0

SCANNER EXP. LEVEL

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. MX-M700N SIMULATION 7 – 42

Image density level

Setting range 0 - 99

Default 50

NOTE: Only the set value is changed and no printing is performed. Item SIMULATION 46-21 EXP.LEVEL SETUP SCANNER(AUTO SET), PRESS START. 0.SCANNER EXP.LEVEL 50

0 1 2 3 4 5 6 7

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

8

2.0 (H)

9

3.0 (H)

10

4.0 (H)

11

5.0 (H)

0 46-22 Purpose

Adjustment

Function (Purpose)

Used to adjust the scanner exposure level in the normal text mode.

Section

—

Operation/Procedure 1)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 5.) * Normal mode (Image density adjustment level)

2)

Press the [START] key.

3)

Enter the image density adjustment value with 10-key.

4)

Press [START] key or press [P] key.

AUTO 1.0 2.0 3.0 4.0 5.0

Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5

50

SIMULATION 46-23 EXP.LEVEL SETUP SCANNER(FINE). SELECT 0-11,AND PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 50 3.3.0 50 4.4.0 50 5.5.0 50 6.AUTO(H) 50 7.1.0(H) 50 8.2.0(H) 50 9.3.0(H) 50 10.4.0(H) 50 11.5.0(H) 50

1

The adjustment value is set.

0 1 2 3 4 5

Default

NOTE: Only the set value is changed and no printing is performed.

* Auto mode

Item

Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range 0 - 99

Setting range 0 - 99

Default 50

46-24 Purpose

Adjustment

Function (Purpose)

Used to adjust the scanner exposure level (in the super fine text mode).

Section

—

NOTE: Only the set value is changed and no printing is performed. SIMULATION 46-22 EXP.LEVEL SETUP SCANNER(NORMAL). SELECT 0-5, AND PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 50 3.3.0 50 4.4.0 50 5.5.0 50

Operation/Procedure 1)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.)

1

* Normal mode (Image density adjustment level) * Normal mode (Image density adjustment level) (Half-tone mode) * Auto mode

46-23 Purpose

* Auto mode (Half-tone mode)

Adjustment

Function (Purpose)

Used to adjust the scanner exposure level in the fine text mode.

Section

—

2)

Press the [START] key.

3)

Enter the image density adjustment value with 10-key.

4)

Press [START] key or press [P] key. The adjustment value is set.

Operation/Procedure 1)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) * Normal mode (Image density adjustment level) * Normal mode (Image density adjustment level) (Half-tone mode) * Auto mode * Auto mode (Half-tone mode)

2)

Press the [START] key.

3)

Enter the image density adjustment value with 10-key.

4)

Press [START] key or press [P] key. The adjustment value is set.

Item 0 1 2 3 4 5 6 7

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

8

2.0 (H)

9

3.0 (H)

10

4.0 (H)

11

5.0 (H)

Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range 0 - 99

Default 50

NOTE: Only the set value is changed and no printing is performed.

MX-M700N SIMULATION 7 – 43

SIMULATION 46-24 EXP.LEVEL SETUP SCANNER(SUPER FINE). SELECT 0-11,AND PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 50 3.3.0 50 4.4.0 50 5.5.0 50 6.AUTO(H) 50 7.1.0(H) 50 8.2.0(H) 50 9.3.0(H) 50 10.4.0(H) 50 11.5.0(H) 50

1

46-27 Purpose

Adjustment

Function (Purpose)

Used to adjust the gamma (density gradient) of the network scanner mode.

Section

—

Operation/Procedure (Scanner mode selection) 1)

Select the number corresponding to the scanner mode to be adjusted with 10-key. (Select one of 1 - 9.)

Adjustment

2)

Press the [START] key.

Function (Purpose)

Used to adjust the scanner exposure level in the ultra fine text mode.

(Gamma adjustment)

Section

—

46-25 Purpose

After completion of the above procedures, perform the following procedures.

Operation/Procedure

1)

Enter the gamma level with 10-key.

1)

2)

Press the [START] key.

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 11.) * Normal mode (Image density adjustment level)

The greater the adjustment value is, the greater the gamma value is, resulting in a higher contrast.

* Normal mode (Image density adjustment level) (Half-tone mode)

Item

* Auto mode

1

OC_Fine.HT

2

OC_SFine.HT

3

OC_UFine.HT

4

SPF_Fine.HT

5

SPF_SFine.HT

6

SPF_UFine.HT

7

CIS_Fine.HT

8

CIS_SFine.HT

9

CIS_UFine.HT

Fine text (Half-tone) (OC) Super fine (Half-tone) (OC) Ultra fine (Half-tone) (OC) Fine text (Half-tone) (SPF) Super fine (Half-tone) (SPF) Ultra fine (Half-tone) (SPF) Fine text (Half-tone) (CIS) Super fine (Half-tone) (CIS) Ultra fine (Half-tone) (CIS)

* Auto mode (Half-tone mode) 2)

Press the [START] key.

3)

Enter the image density adjustment value with 10-key.

4)

Press [START] key or press [P] key. The adjustment value is set. Item 0 1 2 3 4 5 6 7

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

8

2.0 (H)

9

3.0 (H)

10

4.0 (H)

11

5.0 (H)

Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range 0 - 99

Default 50

SIMULATION 46-27 GAMMA SETUP(SCNNER), SELECT 1-9, AND 1.OC_Fine.HT 64 2.OC_SFine.HT 64 4.SPF_Fine.HT 64 5.SPF_SFine.HT 64 7.CIS_Fine.HT 64 8.CIS_SFine.HT 64

Setting range 0 - 127

Default 64

PRESS START. 3.OC_UFine.HT 64 6.SPF_UFine.HT 64 9.CIS_UFine.HT 64

NOTE: Only the set value is changed and no printing is performed. 46-31 SIMULATION 46-25 EXP.LEVEL SETUP SCANNER(ULTRA PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 3.3.0 50 4.4.0 50 5.5.0 6.AUTO(H) 50 7.1.0(H) 50 9.3.0(H) 50 10.4.0(H) 50

Purpose

Adjustment

FINE). SELECT 0-11,AND

Function (Purpose)

Used to adjust sharpness of the copy mode.

50 50 8.2.0(H) 50 11.5.0(H) 50

Section

—

Operation/Procedure (Copy mode selection) 1)

Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 1 - 16.)

2)

Press the [START] key.

(Sharpness adjustment) After completion of the above procedures, perform the following procedures. 1)

Enter the sharpness level with 10-key.

2)

Press the [START] key.

The greater the adjustment value is, the greater the sharpness is.

MX-M700N SIMULATION 7 – 44

: '07 Feb 15

1

Item

1 1 2 3 4 5 6 7

OC_AE OC_CHARA OC_MIX OC_PHOTO SPF1_AE SPF1_CHARA SPF1_MIX

8 9 10 11

SPF1_PHOTO SPF2_AE SPF2_CHARA SPF2_MIX

12 13 14 15 16

SPF2_PHOTO CIS_AE CIS_CHARA CIS_MIX CIS_PHOTO

AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC) AE mode (SPF1) Text mode (SPF1) Text/Photo mode (SPF1) Photo mode (SPF1) AE mode (SPF2) Text mode (SPF2) Text/Photo mode (SPF2) Photo mode (SPF2) AE mode (OC) Text mode (OC) Text/Photo mode (OC) Photo mode (OC)

Setting range 1-5

Default 2 3

2 3

46-45 Purpose

Adjustment

Function (Purpose)

Used to adjust the image density in the FAX mode (600dpi).

Section

—

Operation/Procedure 1)

* Normal mode (Image density adjustment level) 2 3

* Normal mode (Image density adjustment level) (Half-tone mode) * Auto mode * Auto mode (Half-tone mode)

4 3

2)

Press the [START] key.

3)

Enter the image density adjustment value with 10-key. Item

* SPF1: DSPF front surface (CCD) / SPF2: DSPF back surface (CCD) SIMULATION 46-31 SHARPNESS LEVEL SETUP. SELECT 1.OC_AE 3 2.OC_CHARA 3 4.OC_PHOTO 3 5.SPF1_AE 3 7.SPF1_MIX 3 8.SPF1_PHOTO 10.SPF2_CHARA 3 11.SPF2_MIX 13.CIS_AE 3 14.CIS_CHARA 16.CIS_PHOTO 3

1-16, AND PRESS START. 3.OC_MIX 3 6.SPF1_CHARA 3 3 9.SPF2_AE 3 3 12.SPF2_PHOTO 3 3 15.CIS_MIX 3

46-39 Purpose

Adjustment

Function (Purpose)

Used to adjust sharpness of the FAX mode.

Section

—

Operation/Procedure 1)

Enter the sharpness level with 10-key.

2)

Press the [START] key.

The greater the adjustment value is, the greater the sharpness is. Item

1 1 2 3

Level 1 (Half-tone/ Sharpness:Light) Level 2 (Sharpness:Medium light) Level 3 (Normal/ Sharpness:Medium)

Select the number corresponding to one of the following adjustment items with 10-key. (Select one of 0 - 14.)

Setting range 1-3

SIMULATION 46-39 FAX SHARPNESS LEVEL SETUP. SELECT 1-36, AND PRESS START. 1:OC_NORMAL 3 2:OC_FINE 3 3:OC_FINE(H) 1 4:OC_SFINE 3 5:OC_SFINE(H) 1 6:OC_UFINE 3 7:OC_UFINE(H) 1 8:OC_600 3 9:OC_600(H) 1 10:SPF1_NORMAL 3 11:SPF1_FINE 3 12:SPF1_FINE(H) 1 13:SPF1_SFINE 3 14:SPF1_SFINE(H) 1 15:SPF1_UFINE 3 16:SPF1_UFINE(H) 1 17:SPF1_600 3 18:SPF1_600(H) 1 19:SPF2_NORMAL 3 20:SPF2_FINE 3 21:SPF2_FINE(H) 1 22:SPF2_SFINE 3 23:SPF2_SFINE(H) 1 24:SPF2_UFINE 3 25:SPF2_UFINE(H) 1 26:SPF2_600 3 27:SPF2_600(H) 1 28:CIS_NORMAL 3 29:CIS_FINE 3 30:CIS_FINE(H) 1 31:CIS_SFINE 3 32:CIS_SFINE(H) 1 33:CIS_UFINE 3 34:CIS_UFINE(H) 1 35:CIS_600 3 36:CIS_600(H) 1

0

TRAY SELECT

1 2

PRINT START EXP LEVEL

3 4 5 6 7 8 9 10

AUTO 1.0 2.0 3.0 4.0 5.0 AUTO (H) 1.0 (H)

11

2.0 (H)

12

3.0 (H)

13

4.0 (H)

14

5.0 (H)

4)

Paper feed tray selection Print start (Default) Exposure level selection Auto Exposure level 1 Exposure level 2 Exposure level 3 Exposure level 4 Exposure level 5 Auto (Half-tone) Exposure level 1 (Half-tone) Exposure level 2 (Half-tone) Exposure level 3 (Half-tone) Exposure level 4 (Half-tone) Exposure level 5 (Half-tone)

Setting range

Default

0 - 99

50

Press the [START] key. The adjustment value is set.

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

SIMULATION 46-45 EXP.LEVEL SETUP SCANNER(600dpi). SELECT 0-5,AND PRESS START. 0.AUTO 50 1.1.0 50 2.2.0 50 3.3.0 50 4.4.0 50 5.5.0 50 6.AUTO(H) 50 7.1.0(H) 50 8.2.0(H) 50 9.3.0(H) 50 10.4.0(H) 50 11.5.0(H) 50

MX-M700N SIMULATION 7 – 45

1 2 3 4 5 6

48 48-1

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Purpose

Adjustment

Function (Purpose)

Used to adjust the copy magnification ratio (in the main scanning and the sub scanning directions).

When the total of the above set value (1 - 6) and 10 is entered, the mode is changed to the duplex mode.

Section

Optical (Image scanning)

* The copy magnification ratio can be set with the following 1)

Enter 2 with 10-key.

Operation/Procedure

2)

Press the [START] key.

(Adjustment mode selection)

3)

Enter the copy magnification ratio with 10-key.

1)

Select the number corresponding to the copy mode to be adjusted with 10-key. (Select one of 3 - 7.)

4)

Press the [START] key.

2)

Press the [START] key. Item 0

TRAY SELECT

1 2

COPY START MAGNIFICATION

3

CCD (MAIN)

4

CCD (SUB)

5

SPF (SUB)

6

CIS (MAIN)

7

Paper feed tray selection Copy START (Default) Print magnification ratio SCAN main scanning magnification ratio adjustment (CCD) SCAN sub scanning magnification ratio adjustment (CCD) SPF front surface magnification ratio adjustment (Sub scan) SPF back surface magnification ratio adjustment (CIS main scan) SPF front surface magnification ratio adjustment (Main scan)

SPF (MAIN)

Setting range Setting range 0 - 99

Default 50

SIMULATION 48-1 MAGNIFICATION ADJUSTMENT. SELECT 0-7, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.MAGNIFICATION 100 3.CCD(MAIN) 50 4.CCD(SUB) 50 5.SPF(SUB) 50 6.CIS(MAIN) 50 7.SPF(MAIN) 50

2

48-5 Purpose

Adjustment

Function (Purpose)

Used to adjust the copy magnification ratio in the sub scanning direction.

Section

Optical (Image scanning)

Operation/Procedure

(Copy magnification ratio adjustment) 1)

Select the number corresponding to the copy magnification ratio adjustment mode to be adjusted with 10-key. (Select one of 3 - 7.)

2)

Press the [START] key.

3)

Enter the copy magnification ratio adjustment value with 10key.

4)

Press the [P] or [START] key. When [START] key is pressed, copy is performed and the adjustment value is set simultaneously.

When the sub scanning direction image magnification ratio adjustment with SIM 48-1 cannot provide a satisfactory result if a different magnification ration is set and a copy is made, perform this simulation. When there is an error in the copy magnification ratio in reduction copy, change the adjustment value of the high speed mode. When there is an error in the copy magnification ratio in enlargement copy, change the adjustment value of the low speed mode. 1)

Select the number that corresponds to the mode for which to make adjustments with 10-key.

2)

Press the [START] key.

3)

Enter the copy adjustment value with 10-key.

The copy magnification ratio in the sub scan direction can be adjusted by changing the scan speed (motor RPM). Normal display ERROR display

Door open Jam Paper empty

25 - 400 (%)

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

The scanner/SPF motor rotation sped adjustment value is entered. Item 0

MIR (220)

1

MIR (110)

2

SPF (360)

* To select paper (paper feed tray), perform the following procedures.

3

SPF (220)

1)

Enter 0 with 10-key.

4

SPF (110)

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 6.)

4)

Press [START] key. (The paper feed tray is selected.)

The greater the value is, the greater the correction is. One step corresponds to 0.1% adjustment. (Copy condition setting in this simulation)

MX-M700N SIMULATION 7 – 46

Content Scanner motor (220mm/sec) Scanner motor (110mm/sec) SPF motor (360mm/sec) SPF motor (220mm/sec) SPF motor (110mm/sec)

Setting range 0 - 99

Default 50

4)

* Set LEAD to 15. (Enter 15 as the adjustment value of LEAD, and press [P] key.) (0.1mm/step)

The input value is saved by pressing the [START] key SIMULATION 48-5 MOTOR SPEED ADJUSTMENT. SELECT 0-4, AND PRESS START. 0.MIR(220) 50 1.MIR(110) 50 2.SPF(360) 50 3.SPF(220) 50 4.SPF(110) 50

0

* Set DENA to 35. (Enter 35 as the adjustment value of DENA, and press [P] key.) (0.1mm/step) 2)

Make a copy at the normal ratio (100%) and check the lead edge void area and the image loss. (Enter 100 as the set value of the copy magnification ratio (MAGNIFICATION), and press [START] key.)

3)

If an acceptable result is not obtained, do the following steps. * If the leading edge void area is not 3.5 mm:

49

Change the adjustment value of RRCB and perform the adjustment. (Change the adjustment value of RRCB and press [START] key.) (1msec/step)

49-1 Purpose

Setting/update

Function (Purpose)

Firmware updating

Section

—

* If the lead edge image loss is not 1.5mm: Change the adjustment value of RRCA and perform the adjustment. (Change the adjustment value of RRCA and press [START] key.)

Operation/Procedure 1)

Before proceeding to the sim.49-1 screen, insert the USB memory to the main unit. * File and folder of the USB memory are displayed. (When the foldername is longer than 34 characters, it is not completely displayed.)

(The adjustment value should be changed in steps of 0.2mm.) (Trailing edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.)

* If the USB memory is not inserted, "INSERT A USB MEMORY DEVICE CONTAINING MFP FIRMWARE, PLEASE USE FAT (12/16) FORMAT" is displayed.

(Front/rear frame direction image loss adjustment)

* Non compliant to FAT32. If it's inserted, "CAN NOT FAT32. PLEASE USE FAT (12/16) FORMAT" is displayed.

Note that changing this adjustment value shifts the image position in the front/rear frame direction.

2)

Enter the file/folder number of firmware that tries to be updated with 10-key, and press [START] key.

Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.)

3)

If selecting the file, "FIRMWARE UPDATE.. ARE YOU SURE ?" is displayed. ([1]: execute, [2]: get back)

Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.)

* If the operation is normally completed, "COMPLEATE" is displayed. When the error occurs, "ERROR" is displayed.

FIRMWARE UPDATE. SELECT FIRMUP FILE, AND PRESS START. 1. FILE1.sfu 2. FILE2.sfu 3. FILE3.sfu . . 19. >>NEXT Page

Front frame void area = 3.5mm Rear frame void area = 3.5mm

0

Item 0

50 50-1 Purpose

Adjustment

Function (Purpose)

Used to adjust the copy image position and the void area (image loss) adjustment on print paper in the copy mode. (The similar adjustment can be performed with SIM 505 and 50-2 (Simplified method).) (Document table mode) —

Operation/Procedure (Leading edge image loss/void area adjustment) 1)

(Front/rear frame direction void area)

If, as shown above, the front and the rear void areas are not even, use SIM 50-5 to adjust the image off-center position.

SIMULATION 49-1

Section

Set the (SIDE) adjustment value to 20 by entering "20" into the (SIDE) adjustment value field and then pressing the [P] key.

Set the adjustment values for leading edge image loss and leading edge void as follows: (Standard set value) Lead edge image loss: 1.5mm (LEDA: 15)/Paper lead edge void: 3.5mm (DENA: 35)

TRAY SELECT

Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Lead edge adjustment value) 3 RRCA Document scan start position adjustment value 4 RRCB Resist roller clutch ON timing adjustment value 10 SIDE2 ADJ. Correction value for RRCB in the back surface print mode (Image loss set value) 5 LEAD LEAD Lead edge image loss set value 6 SIDE Side image loss set (Void set value) 7 LEAD_EDGE Lead edge void set (DENA) value 8 TRAIL_EDGE Rear edge void (DENB) adjustment value 9 FRONT/REAR Front/Rear void adjustment value

Setting range 1-6

Default -

25 400%

-

0 - 99

50

1 - 99

50

0 - 99

15 20

0 - 99

35

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

MX-M700N SIMULATION 7 – 47

Normal display ERROR display

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

5)

Make a copy at 400%, and calculate the values of L1 and L2. (Enter 100 as the set value (MAGNIFICATION) of the copy magnification ratio, and press [START] key.) (Place a scale on the document table and make a copy.)

(Copy condition setting in this simulation)

L1 = Distance (mm) from the image lead edge position to the scale position of 10mm x 10

* To select paper (paper feed tray), perform the following procedures.

L2 = Distance (mm) from the image lead edge position to the paper lead edge x 10

1)

Enter 0 with 10-key.

6)

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

(Enter the adjustment values of L1 and L2, and press [P] key.)

3)

Enter the number corresponding to the paper feed tray of the target paper with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Enter 2 with 10-key.

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Setting range

4)

If the adjustment result is not satisfactory, perform the above procedures again from the beginning, or use SIM 50-1 to adjust. NOTE: If a satisfactory result is not obtained with the above procedures, through the adjustment values are changed individually, the normal adjustment cannot be made. Perform procedures 3) to 6) continuously. (Trailing edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment)

* The copy magnification ratio can be set with the following 1)

Enter the above values as the set values of L1 and L2.

Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.) When this adjustment value is changed, the image position is shifted in the front/rear frame direction. (Front/rear frame direction void area)

25 - 400 (%)

Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.)

Press the [START] key. SIMULATION 50-1 LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100 (ADJUSTMENT DATA) 3.RRCA 50 4.RRCB 50 10.SIDE2 ADJ. 50 (IMAGE LOSS SETTING) 5.LEAD 15 6.SIDE 20 (VOID SETTING) 7.LEAD_EDGE(DENA) 50 8.TRAIL_EDGE(DENB) 30 9.FRONT/REAR 30

2

50-2 Purpose

Adjustment

Function (Purpose)

Used to adjust the document scan position, the image print position, and the void area (image loss). (Simple adjustment) (This adjustment is the simple method of SIM 501.) (Document table mode)

Section

—

Operation/Procedure (Leading edge image loss/void area adjustment) 1)

Set the RRCB value of SIM 50-1 to 80 - 99.

2)

Set the adjustment values for leading edge image loss adjustment value (LEAD EDGE) and leading edge void adjustment value (DENA) as follows: (Standard set value) Lead edge image loss: 1.5mm (LEDA: 15)/Paper lead edge void: 3.5mm (DENA: 35) * Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD and press [P] key.) * Set the adjustment value of DENA to 35. (Enter 35 as the adjustment value of DENA and press [P] key.)

3)

Set the adjustment value of L1 to 0. (Enter 0 as the adjustment value of L1, and press [P] key.)

4)

Set the adjustment value of L2 to 0. (Enter 0 as the adjustment value of L2, and press [P] key.)

Front frame void area = 3.5mm / Rear frame void area = 3.5mm If, as shown above, the front and the rear void areas are not even, use SIM 50-5 to adjust the image off-center position. Item 0

TRAY SELECT

Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Actual measurement value) 3 L1 Distance from the image lead edge to the scale of 10mm. (Platen 400%, 0.1mm increment) 4 L2 Distance from the paper lead edge to the image lead edge (0.1mm increment) (Image loss set value) 5 LEAD Lead edge image loss set value 6 SIDE Side image loss set value (Void set value) 7 LEAD_EDGE Lead edge void set (DENA) value 8 TRAIL_EDGE Rear edge void (DENB) adjustment value 9 FRONT/REAR Front/Rear void adjustment value

Setting range 1-6

Default -

25 400%

400

0 - 999

-

0 - 99

15 20

0 - 99

35

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. Normal display ERROR display

MX-M700N SIMULATION 7 – 48

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

: '07 Feb 15

1

3)

(Copy condition setting in this simulation)

If an acceptable result is not obtained, do the following steps. * If the leading edge void area is not 3.5 mm:

To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray of the target paper with 10-key.

4)

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

(Shift for the adjustment value change: 0.1mm/step) (Trailing edge void area adjustment) Adjust so that the rear edge void area is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

Repeat the process of changing the (RRCB) adjustment value and then pressing the [START] key. until attaining an acceptable level.

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

(Front/rear frame direction void area) Adjust so that the total of the front/rear direction void areas is 7.0mm. (Change the adjustment values of FRONT/REAR, and press [START] key.) Front frame void area = 3.5mm Rear frame void area = 3.5mm

The copy magnification ratio can be set with the following

(Paper resist adjustment)

1)

Enter 2 with 10-key.

1)

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Setting range

4)

25 - 400 (%)

Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 3 - 9.) (Table 1)

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press [P] key or [START] key. When [START] key is pressed, the adjustment value is set and printing is performed. (Table 2)

Press the [START] key.

If the relative positions of paper and print images vary or a paper jam occurs, change the adjustment value. SIMULATION 50-2 LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS START. 0. TRAY SELECT 1 1.COPY START 2. MAGNIFICATION 400 (ADJUSTMENT) 3.LT 320 4.L2 105 (IMAEG LOSS SETTING) 5.LEAD 15 6.SIDE 20 (VOID SETTING) 7.LEAD_EDGE(DENA) 50 8.TRAIL_EDGE(DENB) 30 9.FRONT/REAR 30

2

(Print condition setting in this simulation) * To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 6.) (Table 3)

50-5

4)

Press [START] key. (The paper feed tray is selected.)

Purpose

Adjustment

Function (Purpose)

Used to adjust the print image position and the void area (image loss) on print paper. (Adjustment as the print engine) (This adjustment is reflected on all the FAX/ printer/copy modes.)

When the total of the above set value (1 - 6) and 10 is entered, the mode is changed to the duplex mode.

Section

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. (Table 1)

—

Operation/Procedure (Print image off-center adjustment)

Item

1)

Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 10 - 16.) (Table 1)

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press [P] key or [START] key. When [START] key is pressed, the adjustment value is set and printing is performed. (Table2)

Check the off-center of the self-print patter of print-out. (Shift for the adjustment value change: 0.1mm/step) The greater the adjustment value is, the more the print image is shifted to the front. (Lead edge void area adjustment) 1)

Set the lead edge void adjustment value (DENA) as specified below. (Standard set value) Paper lead edge void: 3.5mm (DENA: 35) * Set the adjustment value for (DENA) to 35 by entering "35" into the (DENA) adjustment value field and then pressing the [P] key.

2)

Check the lead edge void area on the self print pattern. (Enter 1 and press [START] key.)

0

TRAY Paper feed tray SELECT selection (1 - 6) 1 PRINT Print start (Default) START (Lead edge adjustment value) 2 RRCB Resist roller clutch ON timing adjustment value SIDE2Offset (adjustment) ADJ of the RRCB setting during rear print. (Resist adjustment value) 3 TRAY1 Tray 1 adjustment 4 TRAY2 Tray 2 adjustment 5 TRAY3 Tray 3 adjustment 6 TRAY4 Tray 4 adjustment 7 BPT Manual feed tray adjustment 8 LCC Side LCC adjustment 9 ADU Adjustment when paper is fed again from ADU (Off-center set value) 10 TRAY 1 Tray 1 adjustment 11 TRAY 2 Tray 2 adjustment 12 TRAY 3 Tray 3 adjustment

MX-M700N SIMULATION 7 – 49

Setting range -

Default 55/62 70 (ppm) (ppm) -

-

-

-

0 - 99

50

50

1 - 99

50

50

0 - 99

40 39 40

48 46 47

39

46

50

50

-

1

: '07 Feb 15

1

1

Setting range

Item 13 14

TRAY 4 BPT

15 16

LCC ADU

(Void set value) 17 LEAD_E DGE (DENA) 18 TRAIL_ EDGE (DENB) 19 FRONT/ REAR

Tray 4 adjustment Manual feed tray adjustment Side LCC adjustment Adjustment when paper is fed again from ADU Lead edge void set value

-

Default 55/62 70 (ppm) (ppm) 50 50

3)

Change the adjustment values of SIDE1 and SIDE2, and perform the adjustment. (Change the adjustment values of SIDE1 and SIDE2, and press [START] key.) SIDE1: SPF front surface document lead edge scan position adjustment value SIDE2: SPF back surface document lead edge scan position adjustment value

-

(Shift for the adjustment value change: 0.1mm/step) (The image scan start timing is determined with the detection timing of the document lead edge by the detector SPPD4.)

0 - 99

35

35

Repeat procedures 2) and 3) until a satisfactory result is obtained. (Trailing edge image loss adjustment)

Rear edge void adjustment value

1)

Use the SPF at 100% to make a duplex copy, and check that the rear edge image loss is 1.5mm on the front and the back surfaces. (Select the duplex mode in the paper selection mode of SIM 50-6.) (Enter 100 as the copy magnification ratio set value (MAGNIFICATION), and press [START] key.)

2)

Repeat the process of changing the (TRAIL EDGE) adjustment value and then pressing the [START] key. until attaining an acceptable level.

Front/Rear void adjustment value

(Table 2) Normal display ERROR display

If an acceptable result is not obtained, do the following steps.

Door open Jam Paper empty

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

(Table 3) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

(Front/rear frame direction image loss adjustment) Set the adjustment value of the front surface and the back surface (FRONT/REAR) to 20. (Enter 20 as the adjustment value of FRONT/REAR, and press [P] key.)

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Note that changing this adjustment value shifts the image position in the front/rear frame direction.

SIMULATION 50-5 LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START (ADJUSTMENT DATA) LEAD EDGE: 2.RRCB 50 20.SIDE2 ADJ. 50 RESIST: 3.T1 50 4.T2 50 5.T3 50 6.T4 50 7.BPT 50 8.LCC 50 9.ADU 50 OFF CENTER: 10.T1 50 11.T2 50 12.T3 50 13.T4 50 14.BPT 50 15.LCC 50 16.ADU 50

2

(VOID SETTING) 17.LEAD_EDGE(DENA) 50 18.TRAIL_EDGE(DENB) 30

19.FRONT/REAR 30

50-6 Adjustment

Function (Purpose)

Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-7 (simple method).) (SPF mode) —

* To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key. (Table 3)

4)

Press [START] key. (The paper feed tray is selected.)

1)

Enter 2 with 10-key.

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Setting range

25 - 200 (%)

Press the [START] key.

(Table 1)

(Lead edge image loss adjustment) (Table 1) Set the adjustment values for leading edge image loss for the front and back sides as follows:

Item 0

(Standard set value) Lead edge image loss: 1.5mm (LEAD: 15)/Paper lead edge void: 3.5mm (DENA: 35) * Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD EDGE, and press [P] key.) 2)

(Copy condition setting in this simulation)

4)

Operation/Procedure 1)

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed. (Table2)

* The copy magnification ratio can be set with the following procedures.

Purpose

Section

Repeat the above adjustments until an acceptable result is obtained.

Make a duplex copy at 100% with the SPF, and check that the lead edge (image loss) is 1.5mm either on the front surface and the back surface. (Select the duplex mode in the paper selection mode of SIM 50-6.) (Table 3) (Enter 100 as the copy magnification ratio set value (MAGNIFICATION), and press [START] key.) If an acceptable result is not obtained, do the following steps.

TRAY SELECT

Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Lead edge adjustment value) 3 SIDE1 Front surface document scan start position adjustment value 4 SIDE2 Back surface document scan start position adjustment value

MX-M700N SIMULATION 7 – 50

Setting range 1-6

Default -

25 200%

-

0 - 99

50

Item (Image loss set value: SIDE 1) 5 LEAD_EDGE Front surface lead edge image loss set value 6 FRONT_REAR Front surface side edge image loss set value 7 TRAIL_EDGE Front surface rear edge image loss set value (Image loss set value: SIDE 2) 8 LEAD_EDGE Back surface lead edge image loss set value 9 FRONT/REAR Back surface side edge image loss set value 10 TRAIL_EDGE Back surface rear edge image loss set value

Setting range

Default

0 - 99

15

3)

Set the adjustment value of L5 to 0. (Enter 0 as the adjustment value of L5, and press [P] key.)

4)

Make a copy at 200% with the SPF, and calculate the values of L4 and L5. (Enter 200 as the set value of the copy magnification ratio set value (MAGNIFICATION) and press [START] key.)

20

0 - 20

L4 = Distance (mm) from the image lead edge position to the scale of 10mm x 10 L5 = Distance (mm) from the image lead edge position to the paper lead edge x 10

0

5) 0 - 99

Enter the above values as the set values of L4 and L5. (Enter the adjustment values of L4 and L5, and press [P] key.)

15

(Enter the adjustment values of L4 and L5, and press [P] key.) (The image scan start timing is determined with the detection timing of the document lead edge by the detector SPPD4.)

20

If the adjustment result is not satisfactory, perform the above procedures again or adjust with SIM 50-1. 0 - 20

0

(Table 2)

NOTE: If the adjustment result of the above procedures is not satisfactory, though the adjustment value is changed individually, the adjustment cannot be completed normally. Repeat procedures 2) - 5) until a satisfactory result is obtained.

Normal display ERROR display

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

(Table 3) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

(Trailing edge image loss adjustment) Adjust so that the rear edge image loss is 3.5mm. (Change the adjustment value of TRAIL EDGE, and press [START] key.) (Front/rear frame direction image loss adjustment) Set the adjustment value of SIDE to 20. (Enter 20 as the adjustment value of SIDE, and press [P] key.)

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

Note that changing this adjustment value shifts the image position in the front/rear frame direction.

When the total of the above set value and 10 is entered, the mode is changed to the duplex mode (DD), and a duplex copy is made.

SIMULATION 50-6 LEAD EDGE ADJUSTMENT(SPF). SELECT 0-10, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.) (Table2) (Copy condition setting in this simulation) * To select paper (paper feed tray), perform the following procedures.

2

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key. (Table 3)

4)

Press [START] key. (The paper feed tray is selected.)

(ADJUSTMENT DATA)3.SIDE1 50 4.SIDE2 50 (IMAGE LOSS SETTING) SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0 SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0

50-7 Purpose

Adjustment

Function (Purpose)

Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-6.) (SPF mode)

Section

Enter 2 with 10-key.

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Setting range

4)

25 - 200 (%)

Press the [START] key.

(Table 1) Item 0

(Lead edge image loss adjustment) (Table 1) Set the adjustment values for leading edge image loss adjustment value (LEAD EDGE) for the front and back sides as follows: (Standard set value) Lead edge image loss: 1.5mm (LEAD: 1.5) Paper lead edge void: 3.5mm (DENA: 35) * Set the adjustment value of LEAD to 15. (Enter 15 as the adjustment value of LEAD EDGE, and press [P] key.) 2)

1)

—

Operation/Procedure 1)

* The copy magnification ratio can be set with the following

Set the adjustment value of L4 to 0. (Enter 0 as the adjustment value of L4, and press [P] key.)

TRAY SELECT

Paper feed tray selection (1 - 6) 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Actual measurement value) 3 L4 Distance from the front surface image lead edge to the scale of 10mm (SPF: 200%) 4 L5 Distance from the back surface image lead edge to the scale of 10mm (SPF: 200%) (Image loss set value: SIDE 1)

MX-M700N SIMULATION 7 – 51

Setting range -

Default -

25 200%

200

0 - 999

-

Item 5

LEAD_EDGE

Front surface lead edge image loss set value 6 FRONT_REAR Front surface side edge image loss set value 7 TRAIL_EDGE Front surface rear edge image loss set value (Image loss set value: SIDE 2) 8 LEAD_EDGE Back surface lead edge image loss set value 9 FRONT/REAR Back surface side edge image loss set value 10 TRAIL_EDGE Back surface rear edge image loss set value

Setting range 0 - 99

Default 15

20

0 - 20

0

0 - 99

15

20

0 - 20

0

3 4 5 6 7

TRAY1 TRAY2 TRAY3 TRAY4 BPT

8 9

LCC ADU

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

(Table 3) 1 2 3 4 5 6

Default 50

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press [P] key or [START] key. When [START] key is pressed, the adjustment value set and copying is performed.

Normal display ERROR display

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

(Image off-center adjustment) 1)

Enter 1 with 10-key.

2)

Press the [START] key. The adjustment pattern is printed.

3)

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

Tray 1 adjustment Tray 2 adjustment Tray 3 adjustment Tray 4 adjustment Manual feed tray adjustment Side LCC adjustment Adjustment when paper is fed again from ADU

2)

(Table 2) Normal display ERROR display

Setting range 0 - 99

Item

Check the off-center of the printed image. (UNIT: 0.1mm/step When the adjustment value is increased, the print image is shifted to the front direction.)

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

NOTE: This adjustment can be performed with SIM 50-5. (Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures.

When the total of the above set value and 10 is entered, the mode is changed to the duplex mode (DD), and a duplex copy is made.

SIMULATION 50-7 LEAD EDGE ADJUSTMENT(SPF CALC.). SELECT 0-10, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 200

1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key. (Select one of 1 - 6)

4)

Press [START] key. (The paper feed tray is selected.)

2

1 2 3 4 5 6

(ADJUSTMENT DATA) 3.L4 160 4.L5 160 (IMAGE LOSS SETTING) SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0 SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

When the total of the above set value (1 - 6) and 10 is entered, the mode is changed to the duplex print mode. 50-10

The copy magnification ratio can be set with the following

Purpose

Adjustment

1)

Enter 2 with 10-key.

Function (Purpose)

Used to adjust the print image off-center position. (Adjusted separately for each paper feed section.)

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Section

Setting range

—

25 - 400 (%)

Operation/Procedure

4)

(Print image off-center adjustment)

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

NOTE: This simulation cannot provide an accurate adjustment. Do not use. 1)

Enter the number corresponding to the number of the paper feed tray to be adjusted with 10-key. (Select one of 3 - 9.) Item 0

TRAY SELECT

Paper feed tray selection 1 COPY START Copy START (Default) 2 MAGNIFICATION Print magnification ratio (Off-center adjustment value)

Setting range 1-6 25 400%

Default 100

Press the [START] key.

SIMULATION 50-10 PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

2

(ADJUSTMENT DATA) 3.TRAY1 50 4.TRAY2 50 5.TRAY3 50 6.TRAY4 50 7.BPT 50 8.LCC 50 9. ADU

MX-M700N SIMULATION 7 – 52

50

50-12 Purpose

Adjustment

Function (Purpose)

Used to adjust the scan image off-center position. (Adjusted separately for each scan mode.)

Section

—

Operation/Procedure (Select the scan mode to be adjusted.) 1)

Enter the number corresponding to the scan mode to be adjusted with 10-key. (Select one of 3 - 5.) Item 0

TRAY SELECT

1

COPY START

2

Paper feed tray selection Copy START (Default) Print magnification ratio

MAGNIFICATIO N (Resist adjustment value) 3 PLATEN OC mode adjustment 4 SPF SIDE1 SPF front surface adjustment 5 SPF SIDE2 SPF back surface adjustment

Setting range 1-6

1)

Enter 2 with 10-key.

2)

Press the [START] key.

3)

Enter the copy magnification ratio with 10-key.

Setting range

4)

NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

SIMULATION 50-12 ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS START. 0.TRAY SELECT 1 1.COPY START 2.MAGNIFICATION 100

Default -

-

-

25 - 400%

100

0 - 99

50

25 - 400 (%)

Press the [START] key.

2

(ADJUSTMENT DATA) 3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50

50-27 Purpose

Adjustment

Function (Purpose)

Used to adjust the image loss of the scan image in the FAX/scan mode.

(Scan off-center position adjustment)

Section

—

1)

Enter the scan image off-center position adjustment value with 10-key.

Operation/Procedure

2)

Press [P] key or [START] key.

1)

When [START] key is pressed, copy is performed and the adjustment value is set simultaneously.

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

4)

Press the [START] key.

2)

Press the [START] key.

Normal display ERROR display

Door open Jam Paper empty

NOW COPYING. DOOR OPEN. JAM PAPER EMPTY.

(Select the scan mode to be adjusted.) Enter the number corresponding to the adjustment item with 10-key.

(Shift for the adjustment value change: 1.0mm/step)

Check the off-center of the printed image. Repeat the above adjustments until acceptable results are obtained. (UNIT: 0.1mm/step When the adjustment value is increased, the print image is shifted to the front direction.) (Copy condition setting in this simulation) * To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

Setting range

Item

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed Side LCC

FAX send 1 OC (LEAD_EDGE) 2 OC (FRONT/ REAR) 3 OC (TRAIL_EDGE) 4 SPF (LEAD_EDGE) 5 SPF (FRONT/ REAR) 6 SPF (TRAIL_EDGE) 7 CIS (LEAD_EDGE) 8 CIS (FRONT/ REAR) 9 CIS (TRAIL_EDGE)

When the total of the above set value (1 - 6) and 10 is entered, the mode is changed to the duplex print mode. * The copy magnification ratio can be set with the following procesures.

MX-M700N SIMULATION 7 – 53

OC lead edge OC side OC rear edge SPF lead edge SPF side SPF rear edge CIS lead edge CIS side CIS rear edge

0 - 10 (Unit 1mm)

Default

3 (3mm)

: '07 Feb 15

1

Setting range

Item Scanner mode 10 OC (LEAD_EDGE) 11 OC (FRONT/ REAR) 12 OC (TRAIL_EDGE) 13 SPF (LEAD_EDGE) 14 SPF (FRONT/ REAR) 15 SPF (TRAIL_EDGE) 16 CIS (LEAD_EDGE) 17 CIS (FRONT/ REAR) 18 CIS (TRAIL_EDGE)

2

TRAY1

3

TRAY2

4

TRAY3

5

TRAY4

6

BPT

SPF rear edge

7

LCC

CIS lead edge

8

ADU

CIS side

9

SPF (TOP)

10

SPF (HIGH)

11

SPF (LOW)

12

SPF FEED (TOP) SPF FEED (HIGH) SPF FEED (LOW)

OC lead edge

0 - 10 (Unit 1mm)

OC side

0 (0mm)

OC rear edge SPF lead edge SPF side

CIS rear edge

SIMULATION 50-27 ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND PRESS START. [FAX] 1.OC(LEAD_EDGE) 0 2.OC(FRONT/REAR) 0 3.OC(TRAIL_EDGE) 0 4.SPF(LEAD_EDGE) 0 5.SPF(FRONT/REAR) 0 6.SPF(TRAIL_EDGE) 0 7.CIS(LEAD_EDGE) 0 8.CIS(FRONT/REAR) 0 9.CIS(TRAIL_EDGE) 0 [SCN] 10.OC(LEAD_EDGE) 0 11.OC(FRONT/REAR) 0 12.OC(TRAIL_EDGE) 0 13.SPF(LEAD_EDGE) 0 14.SPF(FRONT/REAR) 0 15.SPF(TRAIL_EDGE) 0 16.CIS(LEAD_EDGE) 0 17.CIS(FRONT/REAR) 0 18.CIS(TRAIL_EDGE) 0

1

13

14

2)

51

Setting range

Item

Default

Tray 1 resist adjustment value Tray 2 resist adjustment value Tray 3 resist adjustment value Tray 4 resist adjustment value Manual feed tray resist adjustment value Side LCC resist adjustment value ADU resist adjustment value SPF resist adjustment value (Top speed) SPF resist adjustment value (High speed) SPF resist adjustment value (Low speed) SPF paper feed resist adjustment value (Top speed) SPF paper feed resist adjustment value (High speed) SPF paper feed resist adjustment (Low speed)

0 - 99

Default 55/62 70 (ppm) (ppm) 40 48 39

46

40

47

39

46

50

50

Press the [START] key.

(Resist adjustment) 1)

Enter the resist adjustment value with 10-key.

51-2

2)

Press the [START] key.

Purpose

Adjustment

Function (Purpose)

Used to adjust the pressure of paper on the resist roller of each section (each paper feed, duplex feed and SPF paper feed of the copier). (This adjustment is required when the print image position variations are considerably great or when paper jams occur frequently.)

When [START] key is pressed, the adjustment value is set and paper feed and copying are performed.

Section

Paper transport Transport)

(Discharge/Switchback/

Operation/Procedure (Select the scan mode to be adjusted.) 1)

Enter the number corresponding to the paper feed tray to be adjusted with 10-key. (Select one of 2 - 14.) Changing the resist amount value by 1shifts the position by 1ms.

1

Item 0 1

TRAY SELECT PRINT START

Paper feed tray selection (1 - 6) Print start (Default)

Setting range -

Default 55/62 70 (ppm) (ppm) -

-

Normal display ERROR display

Door open Jam Paper empty

NOW PRINTING. DOOR OPEN. JAM PAPER EMPTY.

(Copy condition setting in this simulation) To select paper (paper feed tray), perform the following procedures. 1)

Enter 0 with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.) 1 2 3 4 5 6

TRAY1 TRAY2 TRAY3 TRAY4 BPT LCC

TRAY1 TRAY2 TRAY3 TRAY4 Manual paper feed LCC

When the total of the above set value (1 - 6) and 10 is entered, the mode is changed to the duplex print mode. NOTE: When [P] key is pressed after entering an adjustment value in this simulation, the adjustment value is set. When [START] key is pressed, the adjustment value is set and copying is performed.

MX-M700N SIMULATION 7 – 54

1

53-7 SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START. 0.TRAY SELECT 1 1.PRINT START 2.TRAY1 50 3.TRAY2 50 4.TRAY3 50 5.TRAY4 50 6.BPT 50 7.LCC 50 8.ADU 50 9.SPF(TOP) 50 10.SPF(HIGH) 50 11.SPF(LOW) 50 12.SPF FEED(TOP) 50 13.SPF FEED(HIGH) 50 14.SPF FEED(LOW) 50

1

Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to enter the SPF width detection adjustment value.

Section

DSPF

Operation/Procedure 1)

Select the number corresponding to the set item with 10-key. Item

53

1 2 3 4

53-6 Purpose

Adjustment

Function (Purpose)

Used to adjust the DSPF width detection level.

Section

MAX. POSITION POSITION 1 POSITION 2 MIN. POSITION

—

2)

Max. position

Setting range 0 - 1023

Default 66

Adjustment point 1 Adjustment point 2 Min. width

456 713 791

Press the [START] key.

3)

Enter the set value with 10-key.

4)

Press the [START] key.

Operation/Procedure 1)

Open the SPF paper feed guide to the maximum width position.

2)

Select MAX. POSITION with 10-key.

3)

Press the [START] key.

4)

Press the [SYSTEM SETTINGS] key.

5)

Open the SPF paper feed guide to the width for the A4R size.

SIMULATION 53-7 SPF TRAY ADJUSTMENT(MANUAL). SELECT 1-4, AND PRESS START. 1.MAX.POSITION: 66 2.POSITION 1 : 456 3.POSITION 2 : 713 4.MIN.POSITION: 791

1

The max. width detection level is recognized.

6)

Select POSITION 1 with 10-key.

7)

Press the [START] key.

53-8

The A4R width detection level is recognized.

Purpose

Adjustment

8)

Press the [SYSTEM SETTINGS] key.

Function (Purpose)

9)

Set the manual paper feed guide to A5R size width.

Used to adjust the document scan start position. (Used to adjust the scanner scan position in the SPF mode front scan.)

Section

—

10) Select POSITION 2 with 10-key. 11) Press the [START] key.

Operation/Procedure

The A5R width detection level is recognized. 12) Press the [SYSTEM SETTINGS] key.

1)

Enter 2 with 10-key.

13) Open the SPF paper feed guide to the minimum width position.

2)

Press the [START] key.

14) Select MIN. POSITION with 10-key.

3)

Enter the adjustment value with 10key. (1 count: 0.1mm)

15) Press the [START] key.

4)

Press the [START] key.

The minimum width detection level is recognized. If the above procedures are not completed normally, "ERROR" is displayed. If completed normally, "COMPLETE" is displayed.

SIMULATION 53-6 SPF TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START. 1.MAX.POSITION 2.POSITION 1 3.POSITION 2 4.MIN.POSITION

1

Item 2

MANUAL

Manual adjustment (Direct entry of a number)

Setting range 1 - 70

SIMULATION 53-8 SPF SCANNING POSITION ADJUSTMENT. PRESS START. 2.MANUAL

MX-M700N SIMULATION 7 – 55

25

Default 32

55

56

55-1

56-1

Purpose

Setting

Purpose

Data transfer

Function (Purpose)

Used to set the specifications of the engine control operations. (PCU PWB)

Function (Purpose)

Used to transfer the MFP controller data. (Used to repair the PWB.)

Section

—

Section

MFP controller

Operation/Procedure

Operation/Procedure

This simulation is used to change and check the engine soft SW. Set this setting to the default.

1)

There is no need to change this setting in the market.

Select the number corresponding to the data transfer mode with 10-key. 1

SIMULATION 55-1 ENGINNE SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

2

1

3 4 5

55-2 Purpose

Setting

Function (Purpose)

Used to set the specifications of the scanner control operations. (Scanner control PWB)

Section

—

6

Operation/Procedure

7

This simulation is used to change and check the scanner soft SW. Set this setting to the default.

ALL (EEPROM, SRAM, FlashROM) → HDD HDD → ALL (EEPROM, SRAM, FlashROM) EEPROM → HDD HDD → EEPROM SRAM (+ FAX Memory, + Option Memory) → HDD

HDD → SRAM (+ FAX Memory, + Option Memory)

FontROM → HDD

All the contents of memory are transferred to HDD. (Similar to execution of items 3 and 5.) The HDD contents are transferred to all the memories. (Similar to execution of items 4 and 6.) Transfer from EEPROM to HDD Transfer from HDD to EEPROM Transfer from SRAM to HDD. When, however, the FAX memory or an option memory (for FAX memory) * is installed, the contents of the Fax memory are also transferred to HDD. Transfer from HDD to SRAM. When, however, the FAX memory or an option memory (for FAX memory) * is installed, the contents HDD are transferred to the FAX memory as well as the SRAM. Transfer from the font ROM to HDD

* When Flash ROM or OP_Flash ROM is not installed, transfer is not made.

There is no need to change this setting in the market. 2)

Press the [START] key.

3)

The confirmation menu is opened to confirm YES/NO of data transfer. Select one.

SIMULATION 55-2 SCANNER SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

1 2

1 4)

YES NO

Data transfer is executed. Data transfer is not executed.

Press the [START] key.

After completion of transfer, the transfer result is displayed. If there is no error, the machine is automatically reset after completion of data transfer.

55-3 Purpose

Setting

Function (Purpose)

Used to set the specifications of the controller operations. (MFP control PWB)

Section

—

Operation/Procedure This simulation is used to change and check the controller soft SW. Set this setting to the default. There is no need to change this setting in the market.

SIMULATION 55-3 MFP SOFT SW. SETTING. SELECT 1-16, AND PRESS START.

If there is an error, ‘NG’ is displayed. (The machine is not reset.) When restoring from HDD, fit the configurations of the Flash ROM and the optional Flash ROM at back-up. SIMULATION 56-1 DATA COPY. SELECT 1-7, AND PRESS START. 1.ALL(EEPROM,SRAM,FlashROM) → HDD 2.HDD → ALL(EEPROM,SRAM,FlashROM) 3.EEPROM → HDD 4.HDD → EEPROM 5.SRAM(+FAX Memory,+Option Memory) → HDD 6.HDD → SRAM(+FAX Memory,+Option Memory) 7.FontROM → HDD

1

MX-M700N SIMULATION 7 – 56

1

: '07 Feb 15

1

60

Setting range

Item 1 2 3 4

60-1

AE CHARA. MIX PHOTO

Auto exposure mode Text mode Text/Photo mode Photo mode

32 - 82

Default 55/62 70 (ppm) (ppm) 44 38 50 43

Purpose

Operation test/Check

Function (Purpose)

Used to check the MFP control (DRAM) operations (read/write).

2)

Press the [START] key.

Section

ICU

3)

Enter the adjustment value with 10-key.

Operation/Procedure

4)

Press the [START] key.

1)

NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU.

Enter the number corresponding to the memory to be checked with 10-key. 1 2

2)

MFP DRAM ASIC DRAM

ERDH image memory ASIC image memory

SIMULATION 61-2 LASER POWER SETTING(COPY). SELECT 1-4, AND PRESS START. 1. AE 44 2. CHARA. 50 3. MIX 50 4. PHOTO 50

Press the [START] key.

1

The memory read/write operation check is started. After starting the operation, "NOW CHECKING" is displayed during checking. When read/write is normally completed, "OK" is displayed. If an error occurs, "NG" is displayed.

SIMULATION 60-1 DRAM TEST. SELECT 1-2, AND PRESS START. 1. ICU DRAM 2. ASIC DRAM

1

61-3 Purpose

Adjustment

Function (Purpose)

Used to adjust the laser power (absolute value) in the FAX mode. (Only when FAX is installed.)

Section

Scanner (write) unit (LSU)

Operation/Procedure 1)

61 61-1

2)

Press the [START] key.

3)

Enter the adjustment value with 10-key.

Setting range Default

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the scanner (write) unit (LSU).

Section

Select the number corresponding to the adjustment mode with 10-key.

Scanner (write) unit (LSU)

4)

32 - 82 50 (55/62 ppm), 38 (70 ppm)

Press the [START] key.

NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU.

Operation/Procedure Used to check if the LSU delivers output of the sync signal (HSYNC/) or not.

SIMULATION 61-3 LASER POWER SETTING(FAX). PRESS START. 㩷 1. FAX 5㩷 㩷 㩷 䋴

"NOW CHECKING" is displayed during checking. When the test is normally completed, "OK" is displayed. If an error occurs, "NG" is displayed.

1

61-4 SIMULATION 61-1 LSU TEST. PRESS START. 1. LSU

1

Purpose

Adjustment

Function (Purpose)

Used to adjust the laser power (absolute value) in the printer mode.

Section

Scanner (write) unit (LSU)

Operation/Procedure 1)

61-2

Select the number corresponding to the adjustment mode with 10-key.

Purpose

Adjustment

2)

Press the [START] key.

Function (Purpose)

Used to adjust the laser power (absolute value) in the copy mode.

3)

Enter the adjustment value with 10-key.

Section

Scanner (write) unit (LSU)

Setting range Default

Operation/Procedure 1)

Select the number corresponding to the adjustment mode with 10-key.

4)

32 - 82 44 (55/62 ppm), 38 (70 ppm)

Press the [START] key.

NOTE: Be sure to set the default value. If not, a trouble may occur in the LSU. SIMULATION 61-4 LASER POWER SETTING(PRINTER). PRESS START. 㩷㩷㩷 5 㩷 1. PRINTER

1 MX-M700N SIMULATION 7 – 57

1

62

SIMULATION 62-3 HDD R/W TEST(ALL). ARE YOU SURE? 1. YES 2. NO

62-1 Purpose

Data clear

Function (Purpose)

Used to format the hard disk.

Section

MFP controller (HDD)

1

Operation/Procedure

62-6

1)

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the hard disk. (The self diag operation of the SMART function is executed.)

Section

MFP controller (HDD)

Select YES/NO of hard disk format. 1 2

2)

YES NO

Execution Cancel

Press the [START] key.

During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed.

Operation/Procedure 1)

Select the number corresponding to the self diag check mode. 1 2

SIMULATION 62-1 HDD FORMAT. ARE YOU SURE? 1. YES 2. NO

1

2)

SHORT SELF-TEST EXTENDED SELFTEST

Partial test All areas test

Press the [START] key.

During the self diag operation, "EXECUTING" is displayed. If the self diag is completed normally, "0" is displayed. If not, any value but 0 is displayed.

62-2 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the hard disk (read/write). (Only in the model with a disk installed) (Partial check)

Section

MFP controller (HDD)

SIMULATION 62-6 SMART OFFLINE TEST. 1. SHORT SELF-TEST 2. EXTENDED SELF-TEST

1

Operation/Procedure 1)

Select YES/NO of hard disk read/write check. 62-7 1 2

2)

YES NO

Execution Cancel

Purpose

Operation test/Check

Function (Purpose)

Used to check the operations of the hard disk. (The result of the self diag operation of the SMART function is printed out.)

Section

MFP controller (HDD)

Press the [START] key.

During testing, "EXECUTING" is displayed. When test is completed normally, "OK" is displayed. If not, "NG" is displayed.

Operation/Procedure 1)

SIMULATION 62-2 HDD R/W TEST. ARE YOU SURE? 1. YES 2. NO

0

1

1

2)

Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the hard disk (read/write). (All areas check)

Section

MFP controller (HDD)

PRINT START

Press the [START] key.

SIMULATION 62-7 SMART ERROR LOG PRINT OUT. SELECT SETTING, AND PRESS START. 㩷㩷㩷 0. TRAY SELECT :AUTO 㩷ONLY 䋴 1. PRINT START

Select YES/NO of hard disk read/write check. 1 2

TRAY SELECT auto only (Selection is not allowed.) PRINT START

1

Operation/Procedure

2)

TRAY SELECT

The result of the hard disk operation check (the self diag operation of the SMART function) is printed out.

62-3

1)

Enter 1 with 10-key.

YES NO

Execution Cancel

Press the [START] key.

During testing, "EXECUTING" is displayed. When test is completed normally, "OK" is displayed. If not, "NG" is displayed.

MX-M700N SIMULATION 7 – 58

62-11

62-8 Purpose

Data clear

Purpose

Data clear

Function (Purpose)

Used to format the hard disk (the system area excluded).

Function (Purpose)

Section

MFP controller (HDD)

Used to delete document filing data. (The management area (standard folder, folder) is cleared.)

Section

MFP controller (HDD)

Operation/Procedure 1)

Select YES/NO of hard disk (the system area excluded) format. 1 2

2)

YES NO

Operation/Procedure 1)

Select YES/NO of deleting the document filing data. 1 2

Execution Cancel

2)

Press the [START] key.

During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed.

YES NO

Execution Cancel

Press the [START] key.

During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed. NOTE: When executed, this function internally executes the same function as SIM66-10;deleting reservation data, bulletin board data, and confidential data.

SIMULATION 62-8 HDD FORMAT (EXCEPT SYSTEM AREA). ARE YOU SURE? 1.YES 2.NO

1

SIMULATION 62-11 DOCUMENT FILING DATA CLEAR. ARE YOU SURE? 1. YES 2. NO

1

62-9 Purpose

Data clear

Function (Purpose)

Used to format the hard disk (system area)

Section

MFP controller (HDD)

Operation/Procedure 1)

Select YES/NO of hard disk (the system area) format. 1 2

2)

YES NO

Execution Cancel

63-1 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the result of shading correction. (The shading correction data are displayed.)

Section

Optical (Image scanning)

Press the [START] key.

62-10

Operation/Procedure

Purpose

Data clear

Function (Purpose)

Used to delete a job complete list (also to delete job log data)

Section

MFP controller (HDD)

Operation/Procedure 1)

Select YES/NO of deleting the job complete list. 1 2

2)

63

YES NO

Execution Cancel

Press the [START] key.

During formatting, "EXECUTING" is displayed. When formatting is completed normally, "OK" is displayed. If not, "NG" is displayed. NOTE: When executed, this function also deletes the complete queues of E-MAIL, FAX and IFAX, reservation data associated with the image send function, bulletin board data, and confidential data.

SIMULATION 62-10 JOB COMPLETE DATA CLEAR. (WITH JOB LOG DATA) ARE YOU SURE? 1.YES 2.NO

1

CCD data FRONT ODD GAIN Front odd-number pixel gain adjustment value FRONT EVEN GAIN Front even-number pixel gain adjustment value FRONT OFFSET Front black difference REAR ODD GAIN Rear odd-number pixel gain adjustment value REAR EVEN GAIN Rear even-number pixel gain adjustment value REAR OFFSET Rear black difference MIN All pixels min. value MAX All pixels max. value AVE All pixels average value CIS data (Only when DSPF installed.) GAIN Gain adjustment value MAX Pixel max. MIN Pixel min. AVE Pixel average OFFSET Black difference DEV Standard deviation SIMULATION 63-1 SHADING DATA DISPLAY. (CCD) FRONT ODD GAIN: 128 FRONT EVEN GAIN: 255 FRONT OFFSET: 2 REAR ODD GAIN: 128 REAR EVEN GAIN: 255 REAR OFFSET: 2 MIN.: 255 MAX.: 0 AVE.: 255 (CIS) GAIN: 128 MIN.: 255

MX-M700N SIMULATION 7 – 59

OFFSET: 0 AVE.: 255

MAX.: 255 DEV.: 0

5)

63-2

Press the [START] key.

(Print condition setting in this simulation)

Purpose

Adjustment

Function (Purpose)

Used to execute shading.

* To select paper (paper feed tray), perform the following procedures.

Section

Optical (Image scanning)

1)

Select TRAY SELECT with 10-key.

2)

Press [START] key. (The mode is changed to the paper feed tray selection mode.)

3)

Enter the number corresponding to the paper feed tray to be used with 10-key.

4)

Press [START] key. (The paper feed tray is selected.)

Operation/Procedure 1)

Enter the number corresponding to the shading mode to be executed. 1

OC SHADING

2

DSPF SHADING

2)

OC analog level correction and shading correction (Document table mode) DSPF analog level correction and shading correction (SPF mode)

* To adjust the print density, perform the following procedures.

Press the [START] key.

During execution, "EXECUTING" is displayed. When execution is completed normally, "COMPLETED" is displayed. SIMULATION 63-2 SHADING EXECUTION. SELECT1-2, AND PRESS START. 1. OC SHADING 2. DSPF SHADING

1

1)

Select DENSITY with 10-key.

2)

Enter the adjustment value with 10-key.

3)

Press the [START] key.

* To set the print quantity, perform the following procedures. 1)

Select MULTI with 10-key.

2)

Enter the print quantity with 10-key.

3)

Press the [START] key.

* To set the print quality mode, perform the following procedures. 1)

Select MODE with 10-key.

2)

Enter the number corresponding to the print quality mode with 10-key.

3)

Press the [START] key.

63-7 Purpose

Adjustment

Function (Purpose)

Used to adjust the white plate scan start position for shading. (Document table mode)

Section

Scanner (Exposure)

* To set the print level, perform the following procedures. 1)

Select LEVEL with 10-key.

2)

Enter the adjustment value with 10-key.

3)

Press the [START] key.

1)

Enter 1 with 10-key.

NOTE: In some print patterns, changing the level may not change the picture quality.

2)

Press the [START] key.

* To set duplex/simplex print, perform the following procedures.

3)

Enter the adjustment value with 10-key. (1count = 0.5mm)

1)

Select DUPLEX with 10-key.

4)

Press the [START] key.

2)

When a shading error occurs, this adjustment value is changed.

Enter the number corresponding to the operation mode with 10-key.

3)

Press [START] key.

Operation/Procedure

(Table 1) Item 1

CCD

CCD scan

Setting range 1 - 16

SIMULATION 63-7 SHADING POSITION ADJUSTMENT. PRESS START. 㩷 1. CCD 㩷 0㩷 㩷 䋴

Default

0

1

TRAY SELECT 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT 6. LCC PRINT START

2 3

PRINT PATTERN DENSITY

4 5

MULTI MODE 1. STANDARD 2. SMOOTHING 3. TONER SAVE 4. HALF TONE 5. SMOOTHING + TONER SAVE 6. SMOOTHING + HALF TONE 7. TONER SAVE + HALF TONE 8. SMOOTHING + TONER SAVE+ HALF TONE LEVEL

6

1

64 64-1 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the printer section (self-print operation), (The print pattern, the paper feed mode, the print mode, the print quantity, and the density can be optionally set.)

Section

—

Operation/Procedure (Various print patterns output) (Table 1)

6

1)

Select PRINT PATTERN with 10-key.

2)

Enter the number corresponding to the print pattern to be printed with 10-key.

3)

Press the [START] key.

4)

Select PRINT START with 10-key.

7

DUPLEX 1. NO 2. YES

MX-M700N SIMULATION 7 – 60

Paper feed tray 1: Tray 1 2: Tray 2 3: Tray 3 4: Tray 4 5: Manual feed 6: LCC Print execution (Printing of the set data is executed.) Print pattern (Note 1) Graphic density (Valid only when No. 79, 80 or 84 is selected.) Number of print Print mode 1. Standard 2. Smoothing ON 3. Toner save ON 4. Half tone ON 5. Smoothing + toner save 6. Smoothing + half tone 7. Toner save + half tone 8. Smoothing + toner save + half tone

Parameter of print image process: (1 -5) Duplex 1 : Simplex 2 : Duplex

(Note 1) Print pattern 57

CONTROLLER PATTERN Yes

58

Yes

59

Yes

60

Yes

61

Yes

62

Yes

63

Yes

64 65

Yes Yes

66

Yes *1

67

Yes *1

68

Yes *1

69 70

Yes Yes

71 72 73 74 75 76 77 78 79

Yes Yes Yes Yes Yes Yes Yes Yes Yes *1

80

Yes

81

Yes

82

Yes

83

Yes

84 85 86 87

Yes Yes Yes Yes

88 89 90

Yes Yes

NO

1

ENGINE PATTERN Yes

2

Yes

3

Yes

4

Yes

5

Yes

6

Yes

7

Yes

8

Yes

9 10 11 12 13 14 15 16 17 18 19 20 21

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

22

Yes

23

Yes

24

Yes

25

Yes

26

Yes

27

Yes

28

Yes

29 30 31 32 33 34 35 36 37 38 39 40 50

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

NO

CONTROLLER PATTERN

Yes

51

Yes

52

Yes

53

Yes

54

Yes

55

Yes

56

Yes

PATTERN

NOTE

For off-center adjustment Main scanning direction 1 by 5 Main scanning direction 1mm-pitch Main scanning direction 3 by 3 Sub scanning direction 1 by 1 Sub scanning direction 1 by 5 Sub scanning direction 2 by 4 Sub scanning direction 3 by 3 Right oblique 1 by 2 Right oblique 1 by 5 Right oblique 2 by 4 Right oblique 3 by 3 Left oblique 1 by 2 Left oblique 1 by 5 Left oblique 2 by 4 Left oblique 3 by 3 Dot 1 by 1 Dot 3 by 3 Dot Solid black Main scanning direction 1 by 1 Main scanning direction 5 by 1 Main scanning direction 4 by 2 Main scanning direction 3 by 3 Sub scanning direction 1 by 1 Sub scanning direction 5 by 1 Sub scanning direction 4 by 2 Sub scanning direction 3 by 3 Right oblique 2 by 1 Right oblique 5 by 1 Right oblique 4 by 2 Right oblique 3 by 3 Left oblique 2 by 1 Left oblique 5 by 1 Left oblique 4 by 2 Left oblique 3 by 3 Dot 1 by 1 Dot 3 by 3 Dot Solid white All surface 1 by 1 (Vertical) All surface 1 by 1 (Horizontal) All surface 1 by 2 (Vertical) All surface 1 by 2 (Horizontal) All surface 1 by 3 (Vertical) All surface 1 by 3 (Horizontal) All surface 1 by 4 (Vertical)

ENGINE PATTERN

91 98

PATTERN

NOTE

All surface 1 by 4 (Horizontal) All surface 1 by 5 (Vertical) All surface 1 by 5 (Horizontal) All surface 2 by 2 (Vertical) All surface 2 by 2 (Horizontal) All surface 2 by 3 (Vertical) All surface 2 by 3 (Horizontal) All background Special pattern (Vertical) For every other 1 block width 128 pixels/ 32 gradations For every other 1 block width 128 pixels/ 16 gradations For every other 1 block width 128 pixels/ 8 gradations 1-dot pattern Print adjustment pattern with scale (Vertical) Grid pattern Slant line 45 degrees Slant line 26.6 degrees Slant line 63.4 degrees ID/BG pattern Dot pattern 12.5% Dot pattern 28% Dot pattern 50% All surface effort diffusion background All surface dither process background For every other 1 block width 128 pixels/ 32 gradations For every other 1 block width 128 pixels/ 16 gradations For every other 1 block width 128 pixels/ 8 gradations Memory check pattern Cleaning check pattern Offset check pattern Test B image (For aging) 6% printer chart 5% printer chart Toner quantity measuring chart Radiation chart Various data printing

Yes * 1 : Error diffusion process SIMULATION 64-1 SELF PRINT MODE. SELECT 0. TRAY SELECT :1 1. 2. PRINT PATTERN:87 3. 4. MULTI : 1 5. 6. LEVEL : 1 7.

MX-M700N SIMULATION 7 – 61

0-7, AND PRESS START. PRINT START DENSITY :1 MODE :1 DUPLEX :1

1

2)

Enter the number corresponding to the bit to be changed with 10-key.

65

(Example) When the bit of 5 is to be changed, enter 5. The set value of 1/0 is alternatively changed every time when the target key is pressed.

65-1 Purpose

Adjustment

Function (Purpose)

Used to adjust the touch (LCD display section) detection position.

Section

Operation (Display/Operation key)

3)

After completion of setting of all the bits, press [START] key. SIMULATION 66-1 FAX SOFT SW. SETTING. SELECT 2-120, AND PRESS START.

Operation/Procedure

䋱

Touch the four cross marks (+) sequentially. The coordinates of pressed positions are set. When the coordinates setting is completed normally, the display turns gray. When all the four points are set, the display returns to the normal state. SIMULATION 65-1

66-2 Purpose

Data clear

Function (Purpose)

Used to clear the FAX soft switch function data and to set to the default. (Excluding the adjustment values.)

Section

FAX

Operation/Procedure 1)

Set the destination code with 10-key. [Destination code]

65-2 Purpose

Adjustment/Setup/Operation data output/ Check (Display/Print)

Function (Purpose)

Used to check the result of the touch (LCD display) detection position adjustment.

Section

Operation (Display/Operation key)

Operation/Procedure When the touch is touched, the X and Y coordinate values of the touched point and the coordinate values of the specified point are displayed. The coordinate values set with SIM 65-1 are used as the reference. SIMULATION 65-2

400

500

200

0000 0101 1001 0100 1101 0100 0101 1110 0110 1100 1110 1101 1100 1011 1100

Norway Denmark Netherlands Italy Switzerland Austria Indonesia Thailand Malaysia India Philippines Hongkong Russia S. Africa

10000010 00110001 01111011 01011001 10100110 00001010 01010100 1001001 01101100 01010011 10001001 01010000 10111000 10011111

2)

Press the [START] key.

3)

The confirmation menu of YES/NO of clear is displayed. Select one.

䌘䋺

600

180

䌙䋺

200

1 2

4)

YES NO

FAX soft SW is cleared. Not cleared.

Press the [START] key.

The soft switch (except for the adjustment values) is cleared according to the destination selected in procedure 1.

66

After the data clear, the machine is automatically reset. NOTE: When the FAX BOX is not installed, initialization including the adjustment value is performed. (The adjustment value is stored in the FAX BOX.)

66-1 Purpose

Setting

Function (Purpose)

Used to change and check the FAX soft switch functions. (Used to change and check the functions provided for the FAX soft switches.)

SIMULATION 66-2 FAX SOFT SW. CLEAR(WITHOUT ADJUSTMENT VALUE). INPUT COUNTRY CODE, AND PRESS START.

FAX

1 2 3 4 5 6 7 8

Operation/Procedure Setting of soft switches other than SW1 can be changed and checked. 1)

000 011 000 011 011 000 010 111 010 001 111 111 111 111 011

300

140

Section

0 1 0 1 0 0 1 0 0 1 1 1 1 1 0

The codes other than the above are recognized as Japan.

600

40 100 100

Japan U.S.A. Australia U.K. Sweden Newzealand China Singapore TW Other1 Other2 Ohter3 Finland

Enter the soft switch number to be checked or changed with 10-key. The current set state is displayed.

MX-M700N SIMULATION 7 – 62

㪇㪇㪇㪇㪇㪇㪇㪇

66-3 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the FAX PWB memory (read/write). (This adjustment is required when the PWB is replaced with a new one.)

Section

FAX

Operation/Procedure 1)

Enter the number corresponding to the memory to be checked with 10-key.

2)

Press the [START] key.

In the case of All, all memories are checked only once. Check connection wire list NO CHECK Not checked yet. CHECKING Checking OK Check complete OK NG Check complete NG

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

NOSIGNAL 33.6 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33

No signal 26.4 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT

12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT

When [SYSTEM SETTING] key is pressed during execution, execution is stopped.

The error address or the data line is displayed individually.

When a number is entered and [START] key is pressed during execution, the kind of signal can be changed.

Target memory of check MFP SRAM SRAM MFP FLASH FLASH ROM MFP OP.FLASH MODEM EEPROM MODEM SRAM (G/A) MODEM SRAM MODEM SDRAM

SIMULATION 66-4 SIGNAL OUTPUT CHECK.(LEVEL MAX) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21

When “repeat” is selected, the operation is repeated until the result is “NG” or “[SYSTEM SETTING]” is pressed. SIMULATION 66-3 FAX PWB MEMORY CHECK INPUT 1-13, AND PRESS START. 1. All Memory Device Check (once) 2. MFP SRAM(once) 3. MFP SRAM(repeat) 4. MFP FLASH+ OP.FLASH(once) 5. MFP FLASH+ OP>FLASH(repeat) 6. MODEM EEPROM(once) 7. MODEM EEPROM(repeat) 8. MODEM SRAM(G/A)(once) 9. MODEM SRAM(G/A)(repeat) 10. MODEM SRAM(once) 11. MODEM SRAM(repeat) 12. MODEM SDRAM(once) 13. MODEM SDRAM(repeat)

2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam

SELECT 1-32, AND PRESS

3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER

4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT

1

66-5 Purpose

Operation test/Check

Function (Purpose)

Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM.) An output is sent at the send level set by the soft switch. (Only when FAX is installed)

Section

FAX

Operation/Procedure 66-4 Purpose

Operation test/Check

Function (Purpose)

Used to check the output operation of data signals in each data output mode of FAX. (Used to check the operation of MODEM. ) Send level: Max. (Only when FAX is installed)

Section

FAX

Operation/Procedure 1)

Enter the number corresponding to the output mode with 10key.

2)

Press the [START] key.

The output is delivered at the max. send level.

1)

Enter the number corresponding to the output mode with 10key.

2)

Press the [START] key.

The output is delivered at the send level set with the soft switch. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

NOSIGNAL 33.6 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33

No signal 26.4 V34 31.2 V34 28.8 V34 26.4 V34 24.0 V34 21.6 V34 19.2 V34 16.8 V34 14.4 V34 12.0 V34 9.6 V34 7.2 V34 4.8 V34 2.4 V34 14.4 V33

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT

12.0 V33 14.4 V17 12.0 V17 9.6 V17 7.2 V17 9.6 V29 7.2 V29 4.8 V27t 2.4 V27t 0.3 FLG CED 2100 CNG 1100 0.3 V21 ANSam RINGER No RBT

When [SYSTEM SETTING] key is pressed during execution, execution is stopped. When a number is entered and [START] key is pressed during execution, the kind of signal can be changed.

MX-M700N SIMULATION 7 – 63

SIMULATION 66-5 SIGNAL OUTPUT CHECK.(SOFT SW.) START. 1.NOSIGNAL 2.26.4 V34 9.16.8 V34 13.7.2 V34 17.12.0 V33 21.7.2 V17 25.2.4 V27t 29.0.3 V21

2.33.6 V34 6.24.0 V34 10.14.4 V34 14.4.8 V34 18.14.4 V17 22.9.6 V29 26.0.3 FLG 30.ANSam

SELECT 1-32, AND PRESS

3.31.2 V34 7.21.6 V34 11.12.0 V34 15.2.4 V34 19.12.0 V17 23.7.2 V29 27.CED 2100 31.RINGER

1

4.28.8 V34 8.19.2 V34 12.9.6 V34 16.14.4 V33 20.9.6 V17 24.4.8 V27t 28.CNG 1100 32.No RBT

1 2 3 4 5 6 7 8 9 10

NONE PAUSE MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 MESSAGE5 MESSAGE6 MESSAGE7 MESSAGE8

Mute Pause sound Message 1 Message 2 Message 3 Message 4 Message 5 Message 6 Message 7 Message 8

11 12 13 14 15 16 17 18 19 20

MESSAGE9 MESSAGE10 MESSAGE11 MESSAGE12 MESSAGE13 MESSAGE14 MESSAGE15 ALARM RINGER EXT.TEL. RINGER

Message 9 Message 10 Message 11 Message 12 Message 13 Message 14 Message 15 Alarm Call ring External TEL ring

When the number is entered during execution, the kind of signal can be changed. 66-6 Purpose

data output/Check (Display/Print)

Function (Purpose)

Used to print the confidential code. (Used when the confidential code is forgotten.) (Only when FAX is installed)

Section

When [START] key is pressed, the voice message is sent. When [SYSTEM SETTINGS] key is pressed, it is stopped.

SIMULATION 66-8 MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS START. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER

FAX

Operation/Procedure 1)

2

Enter 1 with 10-key and press [START] key. 1

PRINT START

Print start

The paper is automatically selected with the size saved in the image memory. SIMULATION 66-6 CODE PRINT OUT.ȁPRESS START. 1.PRINT START

66-9

ı

Purpose

Operation test/Check

Function (Purpose)

Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) An output is sent at the send level set by the soft switch. (Only when FAX is installed)

Section

FAX

66-7 Purpose

data output/Check (Display/Print)

Function (Purpose)

Used to print the image memory data (memory send/receive). (Only when FAX is installed)

Operation/Procedure 1)

Enter the number corresponding to the output mode with 10key.

Operation/Procedure

2)

Press the [START] key.

All image data stored in the image memory are printed.

The output is delivered at the send level set with the soft switch.

Section

FAX

* The confidential receive data are also printed. 1

PRINT START

Print start

The paper is automatically selected with the size saved in the image memory. SIMULATION 66-7 IMAGE MEMORY PRINT OUT. PRESS START. 1.PRINT START

ı

NONE PAUSE MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 MESSAGE5 MESSAGE6 MESSAGE7 MESSAGE8

Mute Pause sound Message 1 Message 2 Message 3 Message 4 Message 5 Message 6 Message 7 Message 8

11 12 13 14 15 16 17 18 19 20

MESSAGE9 MESSAGE10 MESSAGE11 MESSAGE12 MESSAGE13 MESSAGE14 MESSAGE15 ALARM RINGER EXT.TEL. RINGER

Message 9 Message 10 Message 11 Message 12 Message 13 Message 14 Message 15 Alarm Call ring External TEL ring

When the number is entered during execution, the kind of signal can be changed.

66-8 Purpose

Operation test/Check

Function (Purpose)

Used to check the output operation of various sound signals of FAX. (Used to check the operation of the sound output IC.) Send level: Max. (Only when FAX is installed)

Section

1 2 3 4 5 6 7 8 9 10

FAX

Operation/Procedure 1)

Enter the number corresponding to the output mode with 10key.

2)

Press the [START] key.

The output is delivered at the max. level.

When [START] key is pressed, the voice message is sent. When [SYSTEM SETTINGS] key is pressed, it is stopped.

SIMULATION 66-9 MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS START. 1.NONE 2.PAUSE 3.MESSAGE1 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10 13.MESSAGE11 14.MESSAGE12 15.MESSAGE13 16.MESSAGE14 17.MESSAGE15 18.ALARM 19.RINGER 20.EXT.TEL.RINGER

MX-M700N SIMULATION 7 – 64

2

66-10 Purpose

data output/Check (Display/Print)

Function (Purpose)

Used to clear all data of the image memory (memory send/receive). The confidential data are also cleared at the same time. (Only when FAX is installed)

Section

FAX

1 2 3

NO SIGNAL 11111 11110

No signal 11111 11110

4 5 6

00000 010101 00001

00000 010101 00001

When the number is entered during execution, the kind of signal can be changed. When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped.

Operation/Procedure 1)

Select YES/NO of image memory clear with 10-key. 1 2

2)

YES NO

SIMULATION 66-12 300bps SIGNAL OUTPUT.(SOFT SW.) START.

Image memory clear is executed. Not cleared.

Press the [START] key.

1. NO SIGNAL 5. 010101

The SRAM image data management table and image data in the Flash ROM area and HD (except for filing images) are cleared.

2. 11111 6. 00001

SELECT 1-6, AND PRESS

3. 11110

4. 00000

1

66-13 SIMULATION 66-10 IMAGE MEMORY CLEAR ARE YOU SURE? 1. YES 2. NO

Purpose

Setting

Function (Purpose)

Used to enter (set) the number of FAX dial signal output test. (The dial number set by this simulation is outputted when the dial signal output test is made by SIM 66-14 16. ) (Only when FAX is installed)

Section

FAX

1

66-11 Purpose

Operation test/Check

Function (Purpose)

Section

Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) Send level: Max. (Only when FAX is installed)

Operation/Procedure 1)

Enter the dial number with 10-key. Use 10-key, [*] key, and [#] key to enter the number. The upper limit is 20 digits. When [CLEAR] key is pressed, the mode returns to the initial state.

FAX

Operation/Procedure 1)

Enter the number corresponding to the output mode with 10key.

2)

Press the [START] key.

2)

SIMULATION 66-13 DIAL TEST NUMBER SETTING. INPUT NUMBER AND PRESS START. 0123456789*#01234567

The output is delivered at the max. send level. 1 2 3

NO SIGNAL 11111 11110

No signal 11111 11110

4 5 6

00000 010101 00001

00000 010101 00001

When the number is entered during execution, the kind of signal can be changed. When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped.

SIMULATION 66-11 300bps SIGNAL OUTPUT.(LEVEL MAX) START. 1. NO SIGNAL 2. 11111 3. 11110 5. 010101 6. 00001

Press the [START] key.

66-14 Purpose

Setting/Operation test/Check

Function (Purpose)

Used to set the make time in the FAX pulse dial mode (10pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed)

Section

FAX

SELECT 1-6, AND PRESS 4. 00000

1

0-9:[0-9], *:[*], #:[#]

Operation/Procedure 1) 66-12

Enter 0 with 10-key.

2)

Press the [START] key.

Purpose

Operation test/Check

Function (Purpose)

Used to check the output operation of FAX G3 mode 300bps. (Used to check the operation of MODEM.) An output is send at the send level set by the soft switch. (Only when FAX is installed)

(Dial pulse make time setting)

3)

Enter the set value with 10-key.

FAX

4)

Press the [START] key.

Section

The dial signal is outputted.

Operation/Procedure 1)

Enter the number corresponding to the output mode with 10key.

2)

Press the [START] key.

The output is delivered at the send level set with the soft switch.

1)

Enter 1 with 10-key.

2)

Press the [START] key.

0 1

EXECUTE MAKE TIME

Execution Dial pulse make time setting (0 - 15)

The dial signal is sent with the set value + 29ms. When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped.

MX-M700N SIMULATION 7 – 65

: '07 Feb 15

1

When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped. SIMULATION 66-14 DIAL TEST(10PPS). SELECT 0-1, AND PRESS START. 0. EXECUTE 1. MAKE TIME 7 ; [+29 ms]

SIMULATION 66-16 DIAL TEST(DTMF). SELECT 0-2, AND PRESS START. 0. EXECUTE 1. HIGH 7 (dB) 2. HIGH-LOW 7

1

1

66-15 Purpose

Setting/Operation test/Check

Function (Purpose)

Used to set the make time in the FAX pulse dial mode (20pps) and to test the dial signal output. (The dial number signal set by SIM 66-13 is outputted.) Used to check troubles in dialing and to check the operation. (Only when FAX is installed)

Section

FAX

66-17 Purpose

Setting

Function (Purpose)

Used to check the dial signal (DTMF) output in the FAX tone dial mode. Send level: Max. Used to check the operation. (Only when FAX is installed)

Section

FAX

Operation/Procedure

Operation/Procedure

1)

Enter 0 with 10-key.

1)

Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.

2)

Press the [START] key.

2)

Press the [START] key.

The dial signal is outputted.

The output is delivered at the max. send level.

(Dial pulse make time setting) 1)

Enter 1 with 10-key.

2)

Press the [START] key.

3)

Enter the set value with 10-key.

4)

Press the [START] key. 0 1

EXECUTE MAKE TIME

When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped. SIMULATION 66-17 DTMF SIGNAL OUTPUT.(LEVEL MAX) PRESS START.

INPUT 0-9, *, #, AND

1

Execution Dial pulse make time setting (0 - 15)

The dial signal is sent with the set value + 9ms. When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped.

SIMULATION 66-15 DIAL TEST(20PPS). SELECT 0-1, AND PRESS START. 0. EXECUTE 1. MAKE TIME 7 ; [+9 ms]

66-18 Purpose

Setting

Function (Purpose)

Used to check the dial signal (DTMF) output in the FAX tone dial mode. An output is sent at the send level set by the soft switch. Used to check the operation. (Only when FAX is installed)

Section

FAX

1 Operation/Procedure

66-16 Purpose Function (Purpose)

Section

Setting/Operation test/Check Used to check the dial signal (DTMF) output in the FAX tone dial mode. (The dial number signal set by SIM 66-13 is outputted.) The send level can be set to an optional level. Used to check troubles in dialing and to check the operation. (Only when FAX is installed)

1)

Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.

2)

Press the [START] key.

The signal is sent in the send level set with the soft SW. When [SYSTEM SETTINGS] key is pressed during execution, the operation is stopped. SIMULATION 66-18 DTMF SIGNAL OUTPUT.(SOFT SW.) START.

INPUT 0-9, *, #, AND PRESS

1

FAX

Operation/Procedure 1)

Enter 0 with 10-key.

2)

Press the [START] key.

66-19

The dial signal is outputted.

Purpose

Data transfer

Function (Purpose)

Used to back-up the HDD data into the Flash memory (optional FAX expansion memory). (Only when FAX is installed) FAX

(Dial pulse make time setting) 1)

Enter 1 or 2 with 10-key.

2)

Press the [START] key.

3)

Enter the set value with 10-key.

Section

Press the [START] key.

Operation/Procedure

4)

1) Item

1 0 1 2

EXECUTE HIGH HIGH LOW

Execution High group level High group - Low group

Setting range

Select YES/NO of data transfer (backup). 1 2

YES NO

0 - 15dB 0 - 15

MX-M700N SIMULATION 7 – 66

Backup is executed. Backup is not executed.

2)

Press [START] key.

This function is valid only when the FAX expansion memory is installed.

SIMULATION 66-21 FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START. 1. ED 2. MANAGEMENT 3. FILE MANAGEMENT 4. SYSTEM ERROR 5. PROTOCOL

Backup contents • • • • • • • •

One-touch dial FTP expansion Group expansion Program Use index Standard sender IFAX sender registration FAX sender registration

• • • • • • •

Item name File name FAX receive select table IFAX receive YES/NO Polling allow number Memory box Sender name

ı

66-22

The other contents are not backed up.

SIMULATION 66-19 ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) ARE YOU SURE? 1. YES 2. NO

Purpose

Setting

Function (Purpose)

Used to adjust the handset volume. (Only when the FAX is installed.) (Not used)

Section

FAX

Operation/Procedure

1

1)

Enter the number corresponding to the volume with 10-key.

2)

Press the [START] key. 1 2 3

66-20 Data transfer

Function (Purpose)

Used to read the back-up data by SIM 6619 to the SRAM/HDD. (Only when FAX is installed)

SIMULATION 66-22 HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.

FAX

1. MIN 2. MIDDLE 3. MAX

Operation/Procedure 1)

Select YES/NO of data transfer. 1 2

2)

YES NO

Read/write is executed. Read/write is not executed.

1

66-21 Purpose Function (Purpose)

Section

Adjustment/Setup/Operation data output/ Check (Display/Print) Used to print information related to FAX (various registrations, communication management, file management, system error protocol). (Only when FAX is installed)

Purpose

Setting

Function (Purpose)

Used to the FAX program. (Only when FAX is installed) Not used in the market. (For development)

Section

FAX

Operation/Procedure 1)

Turn OFF the power.

2)

Remove the protect pin.

3)

Turn ON the power.

4)

Enter the SIM 66-23 mode.

5)

Press the [START] key. During execution, "EXECUTING" is displayed. When execution is completed normally, "COMPLETED" is displayed. If an error occurs, "FAIL" is displayed.

6)

Turn OFF the power, and attach the protect pin.

FAX

Operation/Procedure 1)

Enter the number corresponding to the information (item) to be printed with 10-key.

2)

Press the [START] key. 1 2 3 4 5

2

66-23

Press the [START] key.

SIMULATION 66-20 ADDRESS DATA BACK UP. (READ FROM FLASH ROM) ARE YOU SURE? 1. YES 2. NO

Small Medium Large

Selection of 1, 2, and 3 can be made during execution.

Purpose

Section

MIN MIDDLE MAX

ED MANAGEMENT FILE MANAGEMENT SYSTEM ERROR PROTOCOL

SIMULATION 66-23 FAX PROGRAM . EJECT PROTECT PIN, AND PRESS START.

Various registration information Communication management information File management information System error information Protocol information

MX-M700N SIMULATION 7 – 67

66-24

66-27

Purpose

Clear

Purpose

Setting

Function (Purpose)

Used to clear the FAST memory data.

Function (Purpose)

Section

FAX

Used to the transfer number for voice warp. (Only when FAX is installed) Not used in the market. (For development)

Section

FAX

Operation/Procedure 1)

Select YES/NO of data clear.

Operation/Procedure 1 2

2)

YES NO

FAST memory data is cleared Not cleared.

Press [START] key.

1)

Enter the voice warp transfer number (1 - 9, 0, *, #) with 10key.

2)

Press [START] key. SIMULATION 66-27 V-WP TRANSMIT NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567

SIMULATION 66-24 FAST MEMORY DATA CLEAR. ARE YOU SURE? 1. YES 2. NO

66-25

66-28

Purpose

Setting

Purpose

Setting

Function (Purpose)

Used to the FAX number for Modem dial-in. (Only when FAX is installed) Not used in the market. (For development)

Function (Purpose)

Used to record voice messages. (Only when FAX is installed.)

Section

FAX

Section

FAX

Operation/Procedure

Operation/Procedure 1)

Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10key.

2)

Press [START] key.

1)

Enter the number corresponding to the registration number with 10-key.

2)

Use the handset to record a voice message. (Max. 6sec)

3)

Onhook the handset. (End) There are following five kinds of recording.

SIMULATION 66-25 M-D-IN FAX NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567

MESSAGE1 MESSAGE2 MESSAGE3 MESSAGE4 MESSAGE5

Recording Recording Recording Recording Recording

No. 1 No. 2 No. 3 No. 4 No. 5

When [SYSTEM SETTING] key is pressed, recording is interrupted.

66-26 Purpose

Setting

Function (Purpose)

Used to external telephone numbers for Modem dial-in. (Only when FAX is installed) Not used in the market. (For development)

Section

1 2 3 4 5

SIMULATION 66-28 VOICE RECORD. SELECT 1-5, AND PRESS START. 1.MESSAGE1 2.MESSAGE2 3.MESSAGE3 4.MESSAGE4 5.MESSAGE5

1

FAX

Operation/Procedure 1)

Enter the Modem dial-in FAX number (1 - 9, 0, *, #) with 10key.

66-29 Purpose

Clear

2)

Press [START] key.

Function (Purpose)

SIMULATION 66-26 M-D-IN EXTEL NUMBER SETTING. 0-9:[0-9],*:[*],#:[#] INPUT NUMBER AND PRESS START. 0123456789*#01234567

Used to clear data related to an address book (one-touch registration, program registration/expansion, relay memory box registration, each table content).

Section

FAX, Network scanner

Operation/Procedure 1)

Select YES/NO of data clear. 1 2

2)

YES NO

Address book data is cleared. Not cleared.

Press [START] key. SIMULATION 66-29 ADDRESS DATA CLEAR. ARE YOU SURE? 1. YES 2. NO

MX-M700N SIMULATION 7 – 68

1

66-30

66-33

Purpose

Operation test/Check

Purpose

Operation test/Check

Function (Purpose)

Used to check the change in the TEL/LIU status.

Function (Purpose)

Used to check the signal (BUSY TONE/ CNG/CED/FNET/DTMF) detection.

Section

FAX

Section

FAX

Operation/Procedure

Operation/Procedure

The TEL/LIU state is displayed.

The detected signal is highlighted.

When the state is changed, it is highlighted. HS1 HS2 RHS EXHS

Polarity reverse signal Polarity reverse signal Handset hook SW External telephone hook SW

SIMULATION 66-33 SIGNAL DETECT CHECK. BUSY TONE CNG CED

FNET

DTMF

66-34

SIMULATION 66-30 TEL/LIU SENSOR CHECK. HS1 HS2 RHS EXHS

1

Purpose

Operation test/Check

Function (Purpose)

Used to measure the communication time of test image data.

Section

FAX

Operation/Procedure Communication test is performed to measure the time (ms).

66-31

Send is made under the following conditions.

Purpose

Operation check

Function (Purpose)

Used to check the relay operation.

Section

FAX

Operation/Procedure 1)

Enter the number corresponding to the check item with 10-key.

2)

Press [START] key.

Communication means Image quality Density ECM Sender record

Normal text Light ON OFF

SIMULATION 66-34 COMMUNICATION TIME DISPLAY.

SIMULATION 66-31 TEL/LIU SETTING. INPUT 0-1, AND PRESS START. MOVEMENT LEFT:[*] RIGHT:[#] 1. MPXA 2. CION 3. MR 4. EC 5. S. 6. CML 7. DP 8. 1 2 3 4 5 6 7 8

10001100

Memory send

* * * * * ms

66-35 Purpose

Setting

Function (Purpose)

Modem program reloading (Only when FAX is installed) Not used in the market. (For development)

Section

FAX

66-32 Purpose

Operation test/Check

Function (Purpose)

Used to check the receive data (fixed data) from the line.

Operation/Procedure

FAX

1)

Section Operation/Procedure

When check is completed normally, "OK" is displayed. In case of an error, "NG" is displayed. (Display message) CHECKING OK NG

Checking Checking completed (OK) Checking completed (NG)

SIMULATION 66-32 RECEIVED DATA CHECK. CHECKING···.(OK or NG)

Select YES/NO of Modem program reload. 1 2

2)

YES NO

Modem block reload is executed. Not cleared.

Press [START] key.

When reload is completed normally, "OK" is displayed. In case of an error, "CHECK SUM" is displayed. The result of Modem reload is displayed. COMPLETE 81 82 83 84 NG

SIMULATION 66-35 MODEM PROGRAM RELOAD. ARE YOU SURE? 1. YES 2. NO

MX-M700N SIMULATION 7 – 69

Reload completed Check sum error Write error Delete error error Due to loader NG

1

66-36

66-42

Purpose

Operation test/Check

Purpose

Setting

Function (Purpose)

Used to check interface between MFPC controller and MDMC. (Check of the data line or the command line)

Function (Purpose)

Reloads the PIC program installed to FAX BOX.

Section

FAX

Section

FAX

Operation/Procedure

Operation/Procedure 1)

Enter the number corresponding to the check mode with 10key. MFPC ← MFPC → MFPC ← MFPC → MFPC ← MFPC → MFPC ← MFPC →

1 2 3 4 5 6 7 8

2)

MDMC MDMC MDMC MDMC MDMC MDMC MDMC MDMC

Date line once only Date line once only Data line repeat Data line repeat Command line once only Command line once only Command line repeat Command line repeat

NOTE: Before processing, permit writing to the FAX PROGRAMA. (Cancel the write protection) 1)

Press [1] key to carry out the writing. Press [2] key to cancel.

2)

If the operation is normally completed, "OK" is displayed. When the error occurs, "NG" is displayed. (Cause of the ERROR) * State is write-protection. * PIC is not mounted. * Access trouble to PIC

Press [START] key. SIMULATION 66-42 PIC PROGRAM RELOAD ARE YOU SURE? 1.YES 2.NO

When check is completed normally, "OK" is displayed. Incase of an error, "NG" is displayed. When check is "repeat," the operation is continued until the result is NG or [SYSTEM SETTINGS] key is pressed.

SIMULATION 66-36 MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START. 1. 2. 3. 4. 5. 6. 7. 8.

MFPC<-MDMC(DATA once) MFPC->MDMC(DATA once) MFPC<-MDMC(DATA repeat) MFPC->MDMC(DATA repeat) MFPC<-MDMC(CMD once) MFPC->MDMC(CMD once) MDPC<-MDMC(CMD repeat) MFPC->MDMC(CMD repeat)

1

66-43

1

Purpose

Adjustment/Setup

Function (Purpose)

Setting of the PIC adjustment value

Section

FAX

Operation/Procedure NOTE: Before processing, permit writing to the FAX PROGRAMA. (Cancel the write protection)

66-39 Purpose

Setting

Function (Purpose)

Used to set the destination specifications.

Section

FAX

1)

Present setting is highlight-displayed on the side of item.

2)

Use the numeric keys to enter the adjustment value. Press the [P] key to memorizes the input value.

3)

Press [1] to writing the adjustment value collectively to PIC that installed to the FAX BOX. * If the operation is normally completed, "WRITING OK" is displayed. When the error occurs, "NG" is displayed.

Operation/Procedure 1)

Enter the number corresponding to the destination.

2)

Press [START] key.

SIMULATION 66-39 FAX DESTINATION SETUP. SELECT 1-6, AND PRESS START 0. 1. 2. 3. 4. 5. 6.

NO DESTINATION JAPAN U.S.A./CANADA EUROPE AUSTRALIA CHINA ASIA&OTHERS

1

SIMULATION 66-43 PIC ADJUSTMENT VALUE WRITING. ENABLE WRITE PIN (for FAX PROGRAM ROM) SELECT 0-12 AND PRESS START. 0. WRITING for PIC 1. ci_level_judge 22 2. ci_cycle_min 10 3. ci_cycle_max 107 4. ci_range 5 5. ci_count 3 6. cidetect 8 7. fnet_level_judge 1 8. fnet_range 3 9.fnet_time_out 100 10. fnet_count 3 11. poff_time 3 12. mswon_level_judge 3

MX-M700N SIMULATION 7 – 70

1

66-60 Purpose

Setting

Function (Purpose)

Used to set the ACR data.

Section

FAX

Operation/Procedure 1)

Enter the number corresponding to the set item with 10-key.

2)

Press [START] key.

The item list menu can be switched by pressing [P] key. 3)

Enter the setting value with 10-key.

4)

Press [START] key.

This simulation can be executed when soft SW 24-4 and 24-5 are set to 1. Display/Not display is switched by soft SW 24-4 and 24-5. The digit limitation and characters allowed to be inputted depend on the input item.

SIMULATION 66-60 ACR SETTING. SELECT NUMBER, SWITCHING OF MENU:[#] 1.Local Carrier Number 3.Overseas Carrier Number 5. Area Code 7.Version 9.Through Number2 11.Through Number4 13.Through Number6 15.Through Number8 17.Through Number10

AND PRESS START.

1

2.Long-distance Carrier Number 4.By Number 6.Machine Code 8.Through Number1 10.Through Number3 12.Through Number5 14.Through Number7 15.Through Number9 18.Through Number11

67 67-16 Purpose

Operation test/Check

Function (Purpose)

Used to check the operation of the network card.

Section

MFP controller

Operation/Procedure During check, "CHECKING" is displayed. When check is completed normally, "OK" is displayed. In case of an error, "NG" is displayed. (Display message) CHECKING OK NG

Checking Check end (Normal) Check end (Error)

SIMULATION 67-16 NETWORK INTERFACE CARD CHECK. NIC: CHECKING

MX-M700N SIMULATION 7 – 71

MX-M700N [8] SELF DIAG AND TROUBLE CODE 5GTXKEG/WCN

1. Self diag When a trouble occurs in the machine or when the life of a consumable part is nearly expired or when the life is expired, the machine detects and displays it on the display section. This allows the and the serviceman to take the suitable action. In case of a trouble, this feature notifies the occurrence of a trouble and stops the machine to minimize the damage.

Monitors the machine conditions. Detects/analyzes the content.

A. Function and purpose Securing safety. (The machine is stopped on detection of a trouble.)

2)

The damage to the machine is minimized. (The machine is stopped on detection of a trouble.)

3)

By displaying the trouble content, the trouble position can be quickly identified. (This allows to perform an accurate repair, improving the repair efficiency.)

The machine is stopped.

4)

Preliminary warning of running out of consumable parts allows to arrange for new parts in advance of running out. (This avoids stopping of the machine due to running out the a consumable part.)

The content is displayed.

Trouble

Trouble/Warning

B. Self diag message kinds

Warning

Trouble/Warning

1)

Warning

The self diag messages are classified as shown in the table below.

Trouble Class 1



Service man

Class 2

Other Warning

Trouble Other

Warning of troubles which can be recovered by the . (Paper jam, consumable part life expiration, etc.) Warning of troubles which can be recovered only by a serviceman. (Motor trouble, maintenance, etc.) — Warning to the , not a machine trouble (Preliminary warning of life expiration of a consumable part, etc.) Warning of a machine trouble. The machine is stopped. —

Repair

Cancel the selfdiagnostic message with the diagnostics (test commands).

Reset

C. Self diag operation (1)

Troubleshoot the cause.

Self diag operation and related work flow

The machine always monitors its own state.

Standby state

When the machine recognizes a trouble, it stops the operation and dis-plays the trouble message. A warning message is displayed when a consumable part life is nearly expired or is expired. When a warning message is displayed, the machine may be or may not be stopped. The trouble messages and the warning messages are displayed by the LCD. Some trouble messages are automatically cleared when the trouble is repaired. Some other troubles must be cleared by a simulation. Some warning messages of consumable parts are automatically cleared when the trouble is repaired. Some other warning messages must be cleared by a simulation.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 1

A consumable part has reached its lifetime. YES Replace or supply the consumable part.

NO

D. Breakdown sequence (1)

Breakdown mode list

There are following cases of the breakdown mode. Operation enable mode Judgment block

kind of trouble

(DSPF breakdown) Scanner section breakdowns (Mirror motor, lens, copy lamp) FAX board breakdown FAX power OFF Network error Staple breakdown Paper feed tray breakdown (Process control breakdown) PCU section breakdowns (Motor, fusing section, etc.) After-process breakdown Inserter trouble (excluding communication trouble) Laser breakdown HDD breakdown CCD breakdowns (Shading, etc.) CIS breakdowns (Shading, etc.) Scanner communication trouble PCU communication trouble FAX backup battery voltage fall HDD registration data sum error Thermistor trouble (trouble history)

Copy read (including interrupt) U1 ✕

FAX send

Email receive

FAX print

Print

List print

U1 ✕

U1 ✕

{ {

{ {

{ {

Notification to FASThost { {

{

✕

{

✕

{

{

✕

{ { U2 U3 U4 ✕

✕ { { { { {

{ ✕ { { { {

✕ { U2 U3 U4 ✕

{ { U2 U3 U4 ✕

{ { U2 U3 U4 ✕

✕ ✕ { { { {

U5 U7

{ {

{ {

U5 U7

U5 U7

U5 U7

{ {

✕ ✕ U6

{ ✕ U6

{ ✕ U6

✕ ✕ {

✕ ✕ {

✕ ✕ {

{ { {

E6 (10, 11, 14)

✕

✕

✕

{

{

{

{

MFP control

E7 (80)

✕

✕

✕

✕

✕

✕

{

MFP control MFP control

E7 (90) U1 (01, 02)

{ {

✕ ✕

✕ ✕

{ {

{ {

{ {

{ {

MFP control

U2 (50)

{

{

{

{

{

{

{

F2 (39, 46, 47, 48)

{

{

{

{

{

{

{

MFP control MFP control

U2 (00, 11, 12, 22, 23) U7, PF

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

{ {

MFP control

E7 (01, 06)

✕

✕

✕

✕

✕

✕

{

MFP control/ PCU MFP control

E7 (50, 55, 56, 57, 60, 65, 66, 67)

✕

✕

✕

✕

✕

✕

{

L4-30

✕

✕

✕

✕

✕

✕

✕

Scanner Scanner

MFP control/ FAX MFP control MFP control MFP control PCU PCU PCU

PCU PCU PCU MFP control Scanner Scanner

PCU

Trouble code

U5 L1, L3, U2 (80, 81)

F6, F7

CE F1 (10) F3, U6 (LCC) F2 (31, 32, 37) C1, C2, C3, H2, H3, H4, H5, L4 (excluding L4-30), L8, U2 (90, 91), F2, F4 F1 F1 (61, 62) E7 (02 only), L6 E7 (03) E7 (10, 11, 12, 14)

(The machine cannot be operated.) Memory External communication disable (RICA) Image memory trouble, decode error Incompatibility check error Controller fan motor trouble

* For FAX communication, refer to the sheet of "(3) Call request and Callin." * The machine may be operated under some conditions. U1: When detected except when in a job, the machine can be operated in the OC mode. U2: Can be operated except in the staple mode. U3: When detected except in a job, the machine can be operated except with the breakdown tray. U4: Can be operated with some restriction on the image quality depending on the destination. (Low density print)

* Refer to the process control trouble operation table below. U5: When detected except in a job, can be operated except in the trouble paper exit section. U6: When detected except in a job, can be operated in the single surface scan mode. U7: Can be operated except in the inserter tray, if the error is detected in the standby mode.

* Process control trouble operation table Troubl e code F2-31 F2-32 F2-37

Operation /SEC

Error content Process control sensor gain adjustment failure Mark detection failure Mark sensor gain adjustment failure

Machine stop Low density copy Machine stop

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 2

• Trouble mode process The machine can be operated under some conditions. Operations except for the trouble mode are enabled (READY). For the modes which cannot be operated, only setting is enabled and a message is given to show the operations are disabled. (NOT READY in this case) (Display) When a trouble occurs, a dialog is shown. In the mode where the operation is enabled, the OK button is added to the message. In the mode where the operation is disabled, the OK button is not shown and the display is kept until the trouble is canceled. • Writing to the trouble memory In case of a same trouble in this machine, selection is made with the simulation to write into the trouble memory or not. If this simulation is set, any trouble is written into the trouble memory unconditionally. (SIM. 26-35) 0: A same trouble as the previous one is not written. (Default) 1: Any trouble is written into the trouble memory unconditionally.

(2)

Power ON trouble detection sequence.

• When the power is turned ON, if H3, H4, H5, U1, U2, PF, L4-31, F3-12/22, or U6 (LCC-related sub code 09 only) is saved, a trouble code is immediately displayed. E7 (50, 55, 56, 57, 60, 65, 66, 67) trouble is not saved.

MFP controle vent manager

Each block

(Power ON sequence) H3, H4, U1, U2, U6 PF trouble check

When the power is turned on, check is made in each block.

Trouble check is made in each block when initializing and data are sent to the MFP control. H3, H4, H5, L4-31, F3-12/22: Saved in the PCU. U1: Saved in the MFP control . U2: Saved in each block. PF: Saved in the MFP control . U6-09: Saved in the PCU. L4-31: Saved in the PCU. F3-12, 22: Saved in the PCU.

(Trouble cancel sequence) When executing SIM 13, 14, 15, 16, 17

SIM 13: U1 trouble cancel SIM 14: H3, H4, H5, L4-31 trouble cancel SIM 15: LCC (U6), Tray 1, 2 (F3-12, 22) F3-12/22 trouble cancel SIM 16: U2 trouble cancel SIM 17: PF trouble cancel

Communication of trouble status [Trouble data ID] [Trouble code]

sim task

(To the corresponding block) Trouble cancel command Trouble cancel status is communicated.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 3

Trouble cancel (The trouble memory is initialized.)

2. Trouble code list Trouble code Main Sub code code C1 00 CE 00 01 02 03 04 05 06 07

E6 E7

E7

EE F1

F2

08 11 14 01 02 03 06 10 11 12 14 50 55 56 57 60 65 66 67 80 90 EL EU 00 02 03 08 09 10 11 15 19 31 32 33 34 37 38 41 42 43 44 45 46 51 52 60 61 62 00 02 04 05 06

Trouble content

MC trouble Another communication error occurs. The network card is not installed or broken. The specified mail server or the FTP server is not found. The specified server suspends response during transmission of images. The entered name of the FTP server or the for authentication is invalid. The entered directory of the FTP server is invalid. The specified mail server (POP3) is not found. The entered name of the POP3 server or the for authentication is invalid. The specified mail server (POP3) suspends response. CIS shading trouble (White correction) CIS communication trouble System data trouble Laser trouble HDD trouble Decode error trouble CCD shading trouble (Black correction) CCD shading trouble (White correction all pixel adjustment) CCD shading trouble (White correction center adjustment) CCD communication trouble LSU connection trouble Incompatibility check (Engine (PCU) detection) Incompatibility check (Engine (PCU) detection) Incompatibility check (Engine (PCU) detection) Controller connection trouble Incompatibility check (MFP controller detection) Incompatibility check (MFP controller detection) Incompatibility check (MFP controller detection) Communication trouble between the MFP control and the scanner (MFP control detection) MFP control-PCU communication trouble (MFP control detection) Auto developer adjustment trouble (Overtoner error) Auto developer adjustment trouble (Undertoner error) Finisher communication trouble Finisher transport motor abnormality Finisher oscillation motor trouble Finisher staple shift motor trouble Finisher load capacity sensor trouble Finisher/staple motor trouble Finisher/pusher motor trouble Finisher tray lift motor trouble Finisher/alignment motor trouble Finisher saddle folding sensor trouble Finisher-saddle communication trouble Finisher/punch shift motor trouble Finisher/punch motor trouble Finisher/ backup RAM trouble Finisher/punch backup ROM trouble Finisher/saddle positioning plate motor trouble Finisher/saddle guide motor trouble Finisher/saddle alignment motor trouble Finisher/saddle bottom staple motor trouble Finisher/saddle front staple motor trouble Finisher/saddle push motor trouble Finisher/saddle sensor connector connection trouble Finisher/micro switch trouble Finisher-inserter communication trouble Inserter/EEPROM trouble Inserter/reverse sensor trouble Toner control sensor open Toner supply abnormality Improper cartridge (Life cycle error, etc.) CRUM error CRUM ID error

Trouble detection

Mechanism

Option

Electricity

FAX

Supply

—

—

z

PCU Network Network Network Network Network Network Network Network Network Scanner Scanner MFP control PCU MFP control MFP control Scanner Scanner Scanner Scanner PCU PCU PCU PCU MFP control MFP control MFP control MFP control MFP control

z z —

MFP control PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 4

—

—

z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z

Trouble code Main Sub code code F2 31

F3

F4 F6

F7 F9 H2

H3 H3 H4

H5 L1 L3 L4

L6 L8 PF U1 U2

U5 U6

U7 --

32 37 39 46 47 48 12 22 32 42 38 00 01 04 20 21 97 98 01 02 00 01 02 00 01 02 00 01 02 01 00 00 01 02 03 04 06 30 31 10 01 00 01 02 00 11 12 22 23 50 80 81 90 91 30 31 09 20 21 22 00 -

Trouble content

Process control trouble (Photoconductor surface reflection rate abnormality) Process control trouble (Drum marking scan trouble) Drum marking sensor gain adjustment error Process thermistor breakdown Developing thermistor breakdown Room temperature thermistor breakdown Developing humidity sensor break down Machine tray 1 lift-up trouble Machine tray 2 lift-up trouble Machine tray 3 lift-up trouble Machine tray 4 lift-up trouble 38V voltage trouble MFP control-FAX communication trouble (MFP control detection) FAX expansion Flash memory trouble (MFP control detection) FAX modem operation abnormality FAX write protect cancel Abnormal combination of the TEL/LIU PWB and the FAX soft switch FAX-BOX incompatibility trouble Combination error of the FAX-BOX destination information and the machine destination information FAX board EEPROM read/write error PRT centro port check error Thermistor open/Fusing unit not installed (HL1) Thermistor open/Fusing unit not installed (HL2) Thermistor open/Fusing unit not installed (HL3) Fusing section high temperature trouble (HL1) Fusing section high temperature trouble (HL2) Fusing section high temperature trouble (HL3) Fusing section low temperature trouble (HL1) Fusing section low temperature trouble (HL2) Fusing section low temperature trouble (HL3) 5-time continuous POD notreached JAM detection Scanner feed trouble Scanner return trouble Main motor lock detection Drum motor lock detection Fusing motor lock detection Developing motor lock detection Transfer belt separation motor trouble detection Controller fan motor lock detection Paper discharging fan trouble Polygon motor lock detection No full wave signal RIC copy inhibit command receive FAX battery abnormality RTC read error (combined use as FAX, on MFP control PWB) EEPROM read/write error (MFP control) Counter check sum error (MFP control) Adjustment value check sum error (MFP control) SRAM memory check sum error (MFP control) SRAM memory individual data check sum error HDD section individual data check sum error (MFP control) EEPROM read/write error (Scanner) Memory check sum error (Scanner) EEPROM read/write error (PCU) Memory check sum error (PCU) DSPF tray lift-up trouble DSPF tray lift-down trouble LCC lift motor trouble LCC communication trouble LCC transport motor trouble LCC 24V power abnormality addition RIC communication trouble Auditor NOT READY

Trouble detection

Mechanism

Option

Electricity

FAX

Supply

PCU

z

PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU MFP control MFP control FAX FAX FAX FAX FAX

z z z z z z

FAX MFP control PCU PCU PCU PCU PCU PCU PCU PCU PCU PCU Scanner Scanner PCU PCU PCU PCU PCU MFP control MFP control PCU PCU MFP control MFP control MFP control MFP control MFP control MFP control MFP control MFP control MFP control Scanner Scanner PCU PCU Scanner Scanner PCU PCU PCU PCU MFP control MFP control

z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 5

z z z z z

3. Details of trouble code C1-00

MC trouble

Details

Section Case 1

Cause

Case 2

Check and remedy Cause

Case 3

CE-00 Details Section Case 1

CE-01

Details Section Case 1

Case 2

CE-02

Check and remedy Cause Check and remedy

Case 2

Case 3

Three successive MHV-T signals are detected during operation of MHV. Main charger output abnormality (Output open) A trouble signal is outputted from the high voltage transformer. Engine The main charger is not installed properly. The main charger is not assembled properly. Use SIM 8-2 to check the main charger output. Main charger disconnection check The high voltage transformer connector is disconnected. The high voltage harness is disconnected or broken. Connection check

Section Case 1

Case 2

The specified server suspends response during transmission of images. Cause Check and remedy Cause Check and remedy

CE-04

Section Case 1

Case 2

The entered name of the FTP server or the for authentication is invalid. Cause Check and remedy Cause

Improper connection of the network cable Check the connection of the network cable. Check and remedy

The network card is not installed or broken.

CE-05

Improper connection of the network cable Check that the network cable is properly connected. An error occurs in the SMTP server/ FTP server/ NTS. Check the SMTP server/ FTP server/ NTS for any trouble.

The entered name of the FTP server or the for authentication is invalid.

Details

Communication error Cause Check and remedy

The specified server suspends response during transmission of images.

Details

High voltage unit trouble Replace the high voltage unit.

Another communication error occurs.

Improper connection of the network cable Check that the network cable is properly connected. Improper registration of the name or improper ed in the FTP server as the destination Check the name or the ed in the FTP server as the destination.

The entered directory of the FTP server is invalid.

Network card connection trouble Cause Check and remedy Cause Check and remedy

The network card is not installed on the controller. Check that the network card is installed on the controller. Network card control PWB trouble 1) Output the NIC Config. Page to check the NIC version. 2) Replace the NIC.

The specified mail server or the FTP server is not found.

Details Section Case 1

CE-03

The specified mail server or the FTP server is not found. Cause Check and remedy Cause Check and remedy

Cause Check and remedy

Improper connection of the network cable Check that the network cable is properly connected. Network setup trouble 1) Check that the connected network s T/IP protocol. 2) Check from the Web Page to confirm that the Primary/Secondary E-mail server address or the FTP server/ Desktop PC address as the destination is properly set. 3) When the above address is described with the Hostname, check that the DNS server is properly set or not. An error occurs in the SMTP server/ FTP server/ NTS. Check the SMTP server/ FTP server/ NTS for any trouble.

Details Section Case 1

Case 2

The entered directory of the FTP server is invalid. Cause Check and remedy Cause Check and remedy

CE-06

The specified mail server (POP3) is not found.

Details Section Case 1

Case 2

Case 3

Improper connection of the network cable Check that the network cable is properly connected. Check for existence of the directory name in the FTP server ed as the destination. Check for existence of the directory name in the FTP server ed as the destination.

The specified mail server (POP3) is not found. POP3 server access error Cause Check and remedy Cause Check and remedy

Cause Check and remedy

Improper connection of the network cable Check connection of the network cable. Network setup trouble 1) Check that the connected network s T/IP protocol. 2) Check on the Web page that the POP3 server address is correctly set. 3) When the above address is described with the Hostname, check that the DNS server is properly set or not. An error occurs in the POP3 server. Check for any error in the POP3 server.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 6

CE-07

Details Section Case 1

Case 2

The entered name of the POP3 server or the for authentication is invalid.

Details Section Case 1

Case 2

E6-11

Cause Check and remedy Cause

Case 2

Case 3

Case 4

E6-14

Case 2

Case 3

Improper name or ed in the POP3 server Check that the name or the ed for the POP3 server is correct.

POP3 server time-out error Cause Check and remedy Cause Check and remedy

Details

Improper connection of the network cable Check connection of the network cable.

Section Case 1

Case 2

Case 3

E7-02

Cause Check and remedy Cause Check and remedy Cause Check and remedy Cause Check and remedy

Check and remedy Cause Check and remedy Cause Check and remedy

Cause Check and remedy

Section Case 1

When the power is turned on or when the proper gain setup value is not obtained with SIM 63-2 CIS shading (Retry number: 256 times): CIS white reference plate scan level is abnormal when the lamp is lighted. Scanner Defective installation of the harness to the CIS unit CIS unit abnormality CIS unit harness check

Case 3

Case 4

Check and remedy Cause

Reference white plate dirt Clean the reference white plate.

Case 5

CIS lighting trouble Use SIM 5-3 to check the light quantity of CIS.

Case 6

Scanner PWB abnormality Scanner PWB check

Case 7

When an error occurs in an access check to the CIS-ASIC on turning on the power or closing the DSFP cover. (Retry number: 5 times) Communication trouble between the scanner PWB and the CIS-ASIC. (Clock synchronization) Scanner Defective installation of the harness to the CIS unit Check the harness connected to the CIS unit. CIS unit abnormality CIS unit check

Cause Check and remedy Cause Check and remedy Cause

Case 2

E7-03

Check and remedy Cause Check and remedy Cause Check and remedy Cause Check and remedy

Section Case 1

Cause

Case 2

Check and remedy Cause Check and remedy

Case 3

The BD signal from the LSU is kept OFF or ON. When the polygon motor rotation is started and three successive BDT signals of I/O ASIC are detected after forced lighting of laser. Engine The connector to the LSU or the harness in the LSU is disconnected or broken. Check for disconnection of the connector to the LSU. The polygon motor does not rotate properly. Check that the polygon motor rotated properly or not. The position of the laser home position sensor in the LSU is shifted. Use SIM 61-1 to check the LSU operation. A proper voltage is not supplied to the power line of the laser. Replace the LSU unit. Defective lighting of the laser emitting diode Check lighting of the laser emitting diode. PCU PWB abnormality Replace the MFP control PWB. MFP control ASIC PWB abnormality Replace the MFP control PWB.

HDD trouble

Details

Scanner PWB abnormality Scanner PWB check

While reading/writing the HDD system area data, the HDD returns an error response or no response at all for longer than 30 seconds. Controller No HDD is installed on the MFP control PWB. Check installation status of the HDD on the MFP control PWB. HDD does not properly function. • CHECK connection between the HDD and MFP control. • Perform an HDD read/write test using SIM 62-2/3. • Replace HDD. MFP control PWB abnormality Replace the MFP control PWB.

Laser trouble

An error occurs in the POP3 server. Check for any error in the POP3 server.

CIS communication trouble

Cause

Cause Check and remedy Cause Check and remedy

Details

CIS shading trouble (White correction)

Details

Section Case 1

Improper connection of the network cable Check connection of the network cable.

The specified mail server (POP3) suspends response.

Details

Section Case 1

System data trouble

POP3 server authentication check error

Check and remedy

CE-08

E7-01

Cause Check and remedy

Data abnormality in the HDD file management area (cluster chain corrupted) The HDD sends an error response or does not respond for 30 sec. Controller The HDD is not installed properly to the MFP control PWB. Check installation of the HDD to the MFP control PWB. The HDD of the MFP control PWB does not operate properly. Check connection of the harness to the HDD of the MFP control PWB. Use SIM 62-2, -3 to check read/write of the HDD. Replace the HDD. MFP control ASIC PWB abnormality Replace the MFP control PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 7

E7-06 Details Section Case 1

Decode error trouble

Cause Check and remedy

Case 2

E7-10

Cause Check and remedy

Case 2

Case 3

E7-11

Cause Check and remedy Cause Check and remedy Cause Check and remedy

Case 2

Case 3

Case 4

Cause Check and remedy Cause Check and remedy Cause

Check and remedy Cause Check and remedy

Section Case 1

Case 3

CCD black scan level abnormality when the copy lamp is turned off. When the proper offset setup value is not obtained at turning on the power or CCD shading with SIM 63-2. Controller Defective installation of the flat cable to the CCD unit Check installation of the flat cable to the CCD unit.

CCD shading trouble (White correction center adjustment)

Details

Case 2

Case 4

E7-14

Cause Check and remedy Cause Check and remedy Cause

Check and remedy Cause Check and remedy

Scanner PWB abnormality Scanner PWB check Section Case 1

The CCD white reference plate scan level abnormality when lighting the copy lamp When the proper gain setup value is not obtained at turning on the power or CCD shading with SIM 63-2. (Retry number 256 times) Scanner Mirror, lens, reference white plate dirt Clean the mirror, the lens, and the reference white plate. Copy lamp lighting abnormality Check the light quantity and lighting of the copy lamp. (SIM 5-3) Defective installation of the flat cable to the CCD unit Improper installation of the CCD unit CCD unit abnormality CCD unit check Scanner PWB abnormality Scanner PWB check

Case 2

Case 3

E7-50

Cause Check and remedy Cause Check and remedy Cause Check and remedy

Case 2

E7-55

Cause Check and remedy Cause Check and remedy

Communication trouble between the scanner PWB and the CCD-ASIC. (Clock synchronization) When an error occurs in the access check to the CCD-ASIC executed at turning on the power. (Retry number 5 times) Scanner Defective installation of the harness connected to the CCD unit Check the harness connected to the CCD unit. CCD unit abnormality CCD unit check Scanner PWB abnormality Scanner PWB check

The LSU connected does not conform to the machine specifications. When the combination of the pattern of an input port on the PCU and the pattern of a port connected to the LSU is not proper. Engine LSU connection trouble Check connection between the PCU and the LSU and the harness. PCU PWB trouble LSU trouble Check the LSU. Check the PCU.

Incompatibility check (55ppm) (Engine (PCU) detection)

Details Section Case 1

Scanner PWB abnormality Scanner PWB check

LSU connection trouble

Details

Section Case 1

The CCD white reference plate scan level abnormality when lighting the copy lamp When the proper gain setup value is not obtained at turning on the power or CCD shading with SIM 63-2. (Retry number 256 times) Scanner Mirror, lens, reference white plate dirt Clean the mirror, the lens, and the reference white plate Copy lamp lighting abnormality Check the light quantity and lighting of the copy lamp. (SIM 5-3) Defective installation of the flat cable to the CCD unit. Improper installation of the CCD unit 3 CCD unit abnormality. CCD unit check

CCD communication trouble

Details

CCD unit abnormality CCD unit check

CCD shading trouble (White correction all pixel adjustment)

Details

Section Case 1

A decode error occurs in making an image. Controller Garbled data in input from PCI to PM DM trouble Data are garbled in image compression/transfer. Check installation of the PWB. (PCI bus) If the job at occurrence is FAX, check installation of the FAX PWB. For the other cases, check the MFP control PWB. MFP control ASIC PWB abnormality Replace the HDD.

CCD shading trouble (Black correction)

Details

Section Case 1

E7-12

Cause Check and remedy

An error is detected in the internal incompatibility check in the engine (PCU). Engine (PCU) PCU PWB trouble or a improper PCU PWB has been installed. Check the PCU PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 8

E7-56

Incompatibility check (62ppm) (Engine (PCU) detection)

Details Section Case 1

Cause Check and remedy

E7-57

Incompatibility check (70ppm) (Engine (PCU) detection)

Details

Section Case 1

An error is detected in the internal incompatibility check in the engine (PCU). Engine (PCU) PCU PWB trouble or a improper PCU PWB has been installed. Check the PCU PWB.

Cause Check and remedy

E7-80

Details

Section Case 1

Incompatibility check trouble An error is detected in the internal incompatibility check in the engine (PCU). Engine (PCU) PCU PWB trouble or a improper PCU PWB has been installed. Check the PCU PWB.

Controller connection trouble

Details Section Case 1

Cause Check and remedy

E7-65

E7-66

Cause Check and remedy

E7-67

Cause Check and remedy

An error is detected in the internal incompatibility check in the MFP control PWB. MFP control PWB MFP control PWB trouble Check the MFP control PWB

Incompatibility check (70ppm) (MFP controller detection)

Details Section Case 1

An error is detected in the internal incompatibility check in the MFP control PWB. MFP control PWB MFP control PWB trouble Check the MFP control PWB

Incompatibility check (62ppm) (MFP controller detection)

Details Section Case 1

Details

Section Case 1

Cause Check and remedy

Communication establishment error/ framing/ parity/ protocol error. Follows the communication protocol specifications. Communication error, timing abnormality of the communication data and the communication signal line. Controller Defective connection of the slave unit PWB connector. Defective harness between the slave unit PWB and the MFP control PWB. Slave unit PWB mother board connector pin breakage. Check connection of the connector between the slave unit PWB and the MFP control PWB and the harness. Check grounding of the machine.

MFP control-PCU communication trouble (MFP control detection)

Cause

Incompatibility check (55ppm) (MFP controller detection)

Details Section Case 1

Incompatibility trouble between the controller and the engine Controller Improper combination of the controller PWB and the engine Check the MFP controller PWB.

Cause

Check and remedy

E7-90 E7-60

Communication trouble between the MFP control and the scanner (MFP control detection)

Check and remedy

Communication establishment error/ framing/ parity/ protocol error Follows the communication protocol specifications. Communication error, timing abnormality of the communication data and the communication signal line Controller Defective connection of the slave unit PWB connector. Defective harness between the slave unit PWB and the MFP control PWB. Slave unit PWB mother board connector pin breakage. Check connection of the connector between the slave unit PWB and the MFP control PWB and the harness. Check grounding of the machine.

EE-EL Auto developer adjustment trouble (Overtoner error) Details

Section Case 1

Cause

Check and remedy

Described on the toner density control design sppecifications and the change request. When the average of 10 output values of the toner sensor (sampling data) after completion (3 min) of the auto development adjustment is smaller than 1.5V. Engine Toner density sensor trouble. Charging voltage and developing voltage trouble. Toner density trouble Developing unit trouble PCU PWB trouble. Use SIM 25-2 to perform the automatic developing adjustment.

An error is detected in the internal incompatibility check in the MFP control PWB. MFP control PWB MFP control PWB trouble Check the MFP control PWB

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 9

EE-EU Auto developer adjustment trouble (Undertoner error)

F1-03

Finisher oscillation motor trouble

Details Details

Section Case 1

Cause

Check and remedy

F1-00

Section Case 1

Section Case 1

Cause

Case 2

Check and remedy Cause Check and remedy Cause Check and remedy

An error in the communication line test after turning on the power or canceling the simulation. Communication error with the finisher. Follows the communication protocol specifications. Communication error, timing abnormality of the communication data and the communication signal line Engine Improper connection or disconnection of the connector or harness between the machine and the finisher. Check the connector and the harness in the communication line. Finisher control PWB trouble. Control PWB (PCU) trouble. Replace the finisher control PWB or the PCU PWB. Malfunction caused by noises Canceled by turning ON/ OFF the power.

Cause

Check and remedy

Finisher communication trouble

Details

Case 3

Described on the toner density control design specifications and the change request. When the average of 10 output values of the toner sensor (sampling data) after completion (3 min) of the auto development adjustment is smaller than 3.5V. Engine Toner density sensor trouble Charging voltage and developing voltage trouble Toner density trouble Developing unit trouble PCU PWB trouble Use SIM 25-2 to perform the automatic developing adjustment.

F1-08

Finisher staple shift motor trouble

Details

Section Case 1

Cause

Check and remedy

F1-09

Finisher transport motor abnormality

Details

Section Case 1

Cause

Check and remedy

When opening the shutter unit, the opening process is not completed in 1sec. When closing the shutter unit, the closing process is not completed in 1sec. When the tray lift unit is operating in the dangerous area, "Not closed state" of the shutter close sensor is detected. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the transport motor operation.

Section Case 1

Cause

Check and remedy

F1-10

When the received data on performing the sensor test at turning on the power are outside the specified range. When the detected data on calculation of the correction value are outside the specified range. Finisher Sensor breakage Harness disconnection Console finisher control PWB trouble Use SIM 3-2 to check the sensor operation.

Finisher/staple motor trouble

Details

Section Case 1

When the stapler shift motor does not move from the hope position in 4sec when operating the stapler shift motor. When the stapler shift motor does not return to the home position in 4sec when operating the stapler shift motor. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble operation. Use SIM 3-3 to check the staple shift motor

Finisher load capacity sensor trouble

Details

F1-02

When opening the oscillation unit, the opening process is not completed in 1sec. When closing the oscillation unit, the closing operation is not completed in 3sec. When the tray lift unit is operating in the dangerous area, "Not closed state" of the oscillation unit close sensor is detected. When controlling the oscillation unit speed, the encoder input cannot be detected within a specified time. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the motor operation.

Cause

Check and remedy

When the staple unit does not shift from HP within 0.5sec in staple process. When a stapler jam is detected and the staple motor is reversed, the staple motor does not return to HP in 0.5sec. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the staple shift motor operation.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 10

F1-11

Finisher/pusher motor trouble

Details

Section Case 1

Cause

Check and remedy

F1-15

Cause

Check and remedy

F1-19

Cause

Check and remedy

F1-31

Section Case 1

Cause

When operating the tray lift unit, the process is not completed in 12sec. When the tray lift unit is lifting, the tray lift unit upper limit sensor ON is detected. When operating the tray lift unit, en encoder input is not detected in 0.2sec. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the elevator motor operation.

Case 2

Check and remedy Cause

Case 3

F1-33

Check and remedy Cause Check and remedy

Details

When operating the alignment motor, it does not move from the home position in 2sec. When operating the alignment motor, it does not return to the home position in 2sec. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the motor operation.

Section Case 1

Cause

Check and remedy

F1-34

Cause

Check and remedy

Section Case 1

Cause

Check and remedy

F1-37

When operating the punch shift motor, it does not move from the home position in 4sec. When operating the punch shift motor, it does not return to the home position in 4sec. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the motor operation.

When learning the punch unit, it does not complete normally and does not return to the home position. When executing punching, it does not shift from the home position in 0.2sec, or it overruns to go into non-HP state. When operating the punch unit, the encoder input cannot be detected within 0.1sec. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the motor operation.

Finisher/ backup RAM trouble

Details Section Case 1

Malfunction caused by noises Canceled by turning ON/ OFF the power.

Finisher/punch motor trouble

Details

When the motor rotation speed (linear velocity) at every 200msec falls below the specified level. When moving to the home position, the home position sensor does not turn on within the specified time. When shifting from the home position to the lead edge, the home position sensor does not turn off within the specified time. Finisher Sensor breakage Harness disconnection Console finisher control PWB trouble Use SIM 3-2 to check the sensor operation.

Communication error between the finisher and the saddle When the motor rotation speed (linear velocity) at every 200msec falls below the specified level. When moving to the home position, the home position sensor does not turn on within the specified time. When shifting from the home position to the lead edge, the home position sensor does not turn off within the specified time. Finisher Improper connection or disconnection of the connector and the harness between the finisher and the saddle unit. Check the connector and the harness in the communication line. Finisher control PWB trouble Control PWB (PCU) trouble Replace the finisher control PWB.

Finisher/punch shift motor trouble

Finisher saddle folding sensor trouble

Details

Section Case 1

Details

Finisher/alignment motor trouble

Details

Section Case 1

Finisher-saddle communication trouble

Finisher tray lift motor trouble

Details

Section Case 1

When learning the paper exit roller speed, the process is not completed in 10sec. When controlling the paper exit roller speed, an encoder input is not detected in a specified time. Finisher Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble Use SIM 3-3 to check the pusher motor operation and the paddle solenoid operation, or use SIM 3-2 to check the oomerang rotations sensor.

F1-32

Cause Check and remedy

When backup RAM data check sum is NG when turning on the power. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 11

F1-38 Details Section Case 1

Finisher/punch backup ROM trouble

Cause Check and remedy

F1-41

Punch unit backup RAM data are garbled. Finisher Punch control PWB trouble Malfunction caused by noises Replace the punch control PWB.

Finisher/saddle positioning plate motor trouble

F1-45

Finisher/saddle front staple motor trouble

Details

Section Case 1

Cause Check and remedy

Details

Section Case 1

Cause Check and remedy

F1-42

The positioning motor HP sensor does not turn on within 1.33sec after starting the motor. The positioning motor HP sensor does not turn off within 1sec after starting the motor. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

F1-46

Finisher/saddle push motor trouble

Details

Finisher/saddle guide motor trouble

Details

Section Case 1

Cause Check and remedy Cause

F1-43

Cause Check and remedy

F1-44

Section Case 1

Cause Check and remedy

Finisher/saddle alignment motor trouble

Details

Section Case 1

It does not return to the home position within the specified time from starting the guide motor. The HP sensor does not turn off within the specified time when shifting from the home position to the specified position. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

When shifting to the home position, the home position sensor does not turn on. The HP sensor does not turn off within the specified time when shifting from the home position to the specified position. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

Finisher/saddle bottom staple motor trouble

F1-51

Cause Check and remedy

F1-52

Section Case 1

Cause Check and remedy

The home position sensor does not turn off within the specified time after normal starting of the motor. The home positions sensor does not turn on within the specified time after reverse starting of the motor in recovery. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

Section Case 1

The connector connection detection input of the guide HP sensor is off. The connector connection detection input of the push lead edge sensor is off. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

Finisher/micro switch trouble

Details Details

When moving to the home position, the home position sensor does not turn on within the specified time. The push lead edge sensor does not turn on within the specified time after shifting from the home position. When shifting from the home position to the lead edge, the home position sensor does not turn off within the specified time. The lead edge sensor does not turn off within the specified time when shifting from the lead edge position to the home position. The motor RPM at every 50msec falls below the specified level. The lead edge sensor does not turn on within the specified time when shifting from the home position to the lead edge position. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

Finisher/saddle sensor connector connection trouble

Details

Section Case 1

The home position sensor does not turn off within the specified time after normal starting of the motor. The home positions sensor does not turn on within the specified time after reverse starting of the motor in recovery. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

Cause Check and remedy

With all cover PI (photo sensor) ON, the transport cover MS is off fort 1sec continuously from starting copying. With all cover PI (photo sensor) ON, the front cover MS is off fort 1sec continuously from starting copying. With all cover PI (photo sensor) ON, the paper exit cover MS is off fort 1sec continuously from starting copying. Finisher Finisher control PWB trouble Malfunction caused by noises Replace the finisher control PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 12

F1-60

Finisher-inserter communication trouble

F2-02

Toner supply abnormality

Details Details Section Case 1

Cause

Case 2

Check and remedy Cause

Case 3

F1-61

Check and remedy Cause Check and remedy

Data read failure on turning on the power Inserter

Case 1

Cause

Case 2

Check and remedy Cause Check and remedy

Details Section Case 1

Check and remedy

F2-00

Cause Check and remedy

Cause

Check and remedy

F2-04

Section Case 1

Auto adjustment failure on turning on the power Inserter Harness disconnection. Inserter PWB trouble. Use SIM 3-2 to check the sensor operation.

When the toner sensor output value is detected as smaller than 0.5V or greater than 4.5V for 3 times continuously at every 500ms after completion of the auto development adjustment. Engine Connector harness trouble Connector not connected. Check connection of the toner control sensor. Check connection of the connector harness to the main PWB. Check for disconnection of the harness.

Cause Check and remedy

Cause Check and remedy

F2-06 Details Section Case 1

F2-31

Communication with the IC chip cannot be made. Data write failure to the CRUM or data read failure from the CRUM occurs 3 times continuously except for toner cartridge installation detection. Engine IC chip trouble Improper cartridge Insert a proper cartridge.

CRUM ID error

Cause Check and remedy

IC chip trouble Engine Improper cartridge Insert a proper cartridge.

Process control trouble (Photoconductor surface reflection rate abnormality)

Details

Section Case 1

An improper toner bottle is inserted. CRUM (IC chip trouble) Engine IC chip trouble Improper cartridge Insert a proper cartridge.

CRUM error

Details

Section Case 1

Toner remains in the toner bottle when undertoner is detected by the toner concentration sensor in the developing unit. Engine Toner concentration sensor trouble. Toner remaining quantity sensor trouble. Connector harness trouble for the above sensors. Check connector of hopper unit toner motor (TM1) Check connector of toner bottle toner motor (TM2) Check connection of the connector harnesses to the main PWB. Check broken harness for above connections. Check output of the toner concentration sensor (SIM25-1). Check output of the toner remaining quantity sensor (SIM10-2).

Improper cartridge (Life cycle error, etc.)

Details

F2-05

Toner control sensor open

Details

Section Case 1

EEPROM trouble Control circuit runaway due to noises Check that the EEPROM is properly installed. Replace the inserter PWB. Inserter PWB EEPROM access circuit trouble Replace the inserter PWB.

Inserter/reverse sensor trouble

Cause

Section Case 1

Malfunction caused by noises Canceled by turning ON/ OFF the power.

Inserter/EEPROM trouble

Details Section

F1-62

Finisher/inserter communication trouble Inserter Improper connection or disconnection of the connector and the harness between the finisher and the inserter unit Check the connector and the harness in the communication line. Finisher control PWB trouble. Control PWB (PCU) trouble. Replace the finisher control PWB.

Cause Check and remedy

Before starting process control, the drum surface is read by the image density sensor to make the sensor gain adjustment so that the output is fixed to a certain level. Though the sensor gain is changed, the output is not fixed to a certain level. Engine Image density sensor trouble Use SIM 44-02 to perform the process control sensor gain adjustment.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 13

F2-32

Process control trouble (Drum marking scan trouble)

F2-46

Developing thermistor breakdown

Details Details Section Case 1

Case 2

Cause Check and remedy Cause

Case 3

Check and remedy Cause Check and remedy

F2-37

Drum marking sensor gain adjustment error

Details

Section Case 1

Case 2

Cause Check and remedy Cause Check and remedy

Case 3

The drum marking size, density, or the number of units is improper. Engine Drum marking sensor trouble Use SIM 44-02 to perform the process control sensor gain adjustment. Improper connection of the harness between the PCU PWB and the drum marking sensor If "Error" is displayed, it may be considered as a breakdown. Check the sensor and the harness. The drum marking sensor is dirty. OPC drum cleaning trouble If the adjustment is completed, check the drum surface conditions.

Cause Check and remedy

Before starting process control, the drum marking area surface is read by the sensor to make the sensor gain adjustment so that the output is fixed to a certain level. Though the sensor gain is changed, the output is not fixed to a certain level. Engine Drum marking sensor trouble Use SIM 44-02 to perform the process control sensor gain adjustment. Improper connection of the harness between the PCU PWB and the drum marking sensor If "Error" is displayed, it may be considered as a breakdown. Check the sensor and the harness. The drum marking sensor is dirty. OPC drum cleaning trouble If the adjustment is completed, check the drum surface conditions.

Section Case 1

Case 2

Case 3

F2-47

Cause Check and remedy Cause Check and remedy Cause Check and remedy

Case 2

Case 3

F2-48

Cause Check and remedy Cause Check and remedy Cause Check and remedy

Process thermistor breakdown

Details

Section Case 1

Case 2

Case 3

Cause Check and remedy Cause Check and remedy Cause Check and remedy

When the input value of the process thermistor is detected as 235 or greater or 22 or smaller for 3 times continuously. Engine Improper connection of the process thermistor harness. Check connection of the connector and the harness of the process thermistor. Process thermistor trouble Check the process thermistor.

Section Case 1

Case 2

Case 3

When the input value of the process thermistor is detected as 235 or greater or 22 or smaller for 3 times continuously. Engine Improper connection of the room temperature thermistor harness. Check connection of the connector and the harness of the process thermistor. Room temperature thermistor trouble Check the room temperature thermistor. PCU PWB trouble Check the PCU PWB.

Developing humidity sensor break down

Details

F2-39

PCU PWB trouble Check the PCU PWB.

Room temperature thermistor breakdown

Details

Section Case 1

When the input value of the process thermistor is detected as 244 or greater or 20 or smaller for 3 times continuously Engine Developing thermistor harness connection trouble Check connection of the connector and the harness of the developing thermistor. Developing thermistor harness trouble Check the developing thermistor

Cause Check and remedy Cause Check and remedy Cause Check and remedy

When the output value of the development humidity sensor is detected as 38 or smaller or 255 or greater. The output value is the average value of 5 sampling data in the interval of 100ms. Engine Developing humidity sensor harness connection trouble Check connection of the connector and the harness of the developing humidity sensor. Developing humidity sensor trouble Check the developing humidity sensor PCU PWB trouble Check the PCU PWB.

PCU PWB trouble Check the PCU PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 14

F3-12

Machine tray 1 lift-up trouble

Details

Section Case 1

Cause

Check and remedy

F3-22

Machine tray 2 lift-up trouble

Details

Section Case 1

Cause

Check and remedy

F3-32

MED does not turn on within the specified time. MCLUD does not turn on within the specified time. The trouble occurs 3 times continuously that the upper limit sensor does not turn on by lift-up operation for 21sec when inserting a tray or for 2sec when printing. For the first and the second times, guide the to pull out the tray in case of a tray size error. Engine MED, MCLUD trouble No. 2 tray lift-up motor trouble Improper connection of the harness of the PCU PWB, the lift-up unit, and the paper feed unit Check the harness and the connector of MED and MCLUD. Lift-up trouble unit check. Use SIM 15 to cancel the trouble.

Machine tray 3 lift-up trouble

Details

Section Case 1

PED does not turn on within the specified time. LUD does not turn on within the specified time. The trouble occurs 3 times continuously that the upper limit sensor does not turn on by lift-up operation for 21sec when inserting a tray or for 2sec when printing. For the first and the second times, guide the to pull out the tray in case of a tray size error. Engine PED, LUD trouble No. 1 tray lift-up motor trouble Improper connection of the harness of the PCU PWB, the lift-up unit, and the paper feed unit Check the harness and connector of PED and LUD Lift-up trouble unit check. Use SIM 15 to cancel the trouble.

Cause

Check and remedy

MED does not turn on within the specified time. MCLUD does not turn on within the specified time. The trouble occurs 3 times continuously that the upper limit sensor does not turn on by lift-up operation for 10sec when inserting a tray or for 2sec when printing. For the first and the second times, guide the to pull out the tray in case of a tray size error. Engine MED, MCLUD trouble No. 3 tray lift-up motor trouble Improper connection of the harness of the PCU PWB, the lift-up unit, and the paper feed unit Check the harness and the connector of MED and MCLUD. Lift-up trouble unit check

F3-42

Machine tray 4 lift-up trouble

Details

Section Case 1

Cause

Check and remedy

F4-38

38V voltage trouble

Details

Section Case 1

Cause

Case 2

Check and remedy Cause Check and remedy

F6-00

Cause

Check and remedy Case 2

Cause Check and remedy

F6-01

The booting sequence by the command line (9600bps, serial) is not completed normally. Communication establishment error/ framing/ parity/protocol error FAX Defective connection of the slave unit PWB connector. Defective harness between the slave unit PWB and the MFP control PWB. Slave unit PWB mother board connector pin breakage. Check connection of the connector between the slave unit PWB and the MFP control PWB and the harness. Slave unit ROM trouble/no ROM/ Reversed insertion of ROM/ ROM pin breakage Check the ROM on the slave unitPWB.

FAX Flash memory trouble (MFP control detection)

Details Section Case 1

38V voltage falls or rises. When the 38V MON signal is not turned on in 50ms after turning on the INTRP. Engine Improper connection or disconnection of the connector and the harness Check the connector and the harness of the power line. PCU PWB trouble Power unit trouble Check 38V power source in the power unit and the PCU PWB.

MFP control-FAX communication trouble (MFP control detection)

Details

Section Case 1

MED does not turn on within the specified time. MCLUD does not turn on within the specified time. The trouble occurs 3 times continuously that the upper limit sensor does not turn on by lift-up operation for 10sec when inserting a tray or for 2sec when printing. For the first and the second times, guide the to pull out the tray in case of a tray size error. Engine MED, MCLUD trouble No. 4 tray lift-up motor trouble. Improper connection of the harness of the PCU PWB, the lift-up unit, and the paper feed unit. Check the harness and the connector of MED and MCLUD. Lift-up trouble unit check.

Cause Check and remedy

The flash memory inserted to the FAX I/F PWB could not be cleared. FAX The flash memory could not be cleared. FAX image save flash memory check. Use SIM 66-10 to clear the expansion flash memory.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 15

F6-04

FAX modem operation abnormality

Details Section Case 1

Case 2

F6-20

Cause Check and remedy Cause Check and remedy

Case 2

Cause Check and remedy Cause Check and remedy

F6-21

Abnormal combination of the TEL/LIU PWB and the FAX soft switch

Details

Section Case 1

Case 2

Case 3

The write protect jumper of the FAX interface PWB is released. FAX The FAX write protect pin is set to Write Enable. Check the write protect pin in the FAX interface PWB. FAX interface PWB trouble FAX PWB trouble Replace the FAX PWB. Replace the FAX interface PWB.

Cause

Check and remedy Cause Check and remedy Cause Check and remedy

Combination error of TEL/LIU PWB and software If the destination of the installed TEL/LIU PWB differs from that of the FAX soft switch, it is judged as an error. Or when the TEL/LIU PWB is not a new one for a new MDMC PWB. FAX The destination of the installed TEL/LIU PWB differs. The FAX PWB information (soft switch) differs. Check the destination of the TEL/LIU PWB. Check the FAX PWB information (soft switch). TEL/LIU PWB trouble Replace the TEL/LIU PWB. The TEL/LIU PWB is not a new one. Replace the TEL/LIU PWB with a new one.

Combination error of the FAX-BOX destination information and the machine destination information

Details

Section Case 1

Cause

Check and remedy

FAX write protect cancel

Details Section Case 1

The initializing process of the modem chip in the FAX PWB is not completed normally. FAX SW101 in the FAX PWB tries to perform normal operation on the boot side. Set SW101 on the FAX PWB to other than the boot side, and turn on the power again. FAX PWB modem chip operation trouble Replace the FAX PWB.

F6-98

F7-01 Details Section Case 1

FAX board EEPROM read/write error

Cause Check and remedy

H2-00

Cause

Check and remedy

H2-01

FAX-BOX incompatibility trouble

Details

Section Case 1

Cause

Check and remedy

The FAX-BOX PWB is not one for the main unit. (FAX detection) If the FAX-BOX modem controller PWB information (hard detection) is not for the main unit, it is judged as an error. FAX Because the FAX-BOX modem controller PWB information (hard detection) is not for the main unit. Check the FAX-BOX modem controller PWB. Replace it with a modem controller PWB for the main unit.

Section Case 1

Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed Engine Thermistor trouble. Control PWB trouble Improper connection of the fusing section connector. AC power trouble. Fusing unit not installed. Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

Thermistor open/Fusing unit not installed (HL2)

Details

F6-97

ACK from the EEPROM cannot be checked. FAX EEPROM trouble FAX PWB EEPROM access circuit trouble Replace the EEPROM. Re-setup the soft SW.

Thermistor open/Fusing unit not installed (HL1)

Details

Section Case 1

When the destination information stored in the FAX-BOX EEPROM is compared with that of the machine, and if the combination is improper, it is judged as an error. FAX Because of improper combination between the destination information stored in the EEPROM on the FAX-BOX PWB and that of the machine (set with SIM 26-6). Check the destination of the FAX-BOX. Check the machine destination with SIM 26-6. Use a proper combination of the machine and the FAX-BOX.

Cause

Check and remedy

Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed Engine Thermistor trouble Control PWB trouble Improper. connection of the fusing section connector. AC power trouble. Fusing unit not installed. Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 16

H2-02

Thermistor open/Fusing unit not installed (HL3)

Details

Section Case 1

Cause

Check and remedy

H3-00

Cause

Check and remedy

H3-01

The fusing temperature exceeds 241.5 °C. (An input voltage of 1.3V or less is detected.) When fusing temperature control is started and a temperature of 242 °C is detected 3 times continuously in sampling of 250 msec interval. (In the interval of 150ms) Engine Thermistor trouble Control PWB trouble Improper connection of the fusing section connector AC power trouble Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp keeps ON. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

Fusing section high temperature trouble (HL2)

Details

Section Case 1

Fusing section high temperature trouble (HL3)

Details

Section Case 1

Cause

Check and remedy

Fusing section high temperature trouble (HL1)

Details

Section Case 1

Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed Engine Thermistor trouble. Control PWB trouble. Improper connection of the fusing section connector. AC power trouble. Fusing unit not installed. Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

H3-02

Cause

Check and remedy

The fusing temperature exceeds 241.5 °C. (An input voltage of 1.3V or less is detected.) When fusing temperature control is started and a temperature of 242 °C is detected 3 times continuously in sampling of 250 msec interval. (In the interval of 150ms) Engine Thermistor trouble. Control PWB trouble. Improper connection of the fusing section connector. AC power trouble. Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp keeps ON. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

H4-00

Fusing section low temperature trouble (HL1)

Details

Section Case 1

The fusing temperature exceeds 241.5 °C. (An input voltage of 1.3V or less is detected.) When fusing temperature control is started and a temperature of 242 °C is detected 3 times continuously in sampling of 250 msec interval. (In the interval of 150ms) Engine Thermistor trouble Control PWB trouble Improper connection of the fusing section connector AC power trouble Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp keeps ON. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

Cause

Check and remedy

The set temperature is not reached within the specified time (normally 3 min or 5 min in the curl prevention mode) after turning on the power relay. When the heater lamp is not turned off in 4 min after starting the warm-up operation. When the set value of -40°C is detected for 5 times continuously in the specified interval after completion of the warm-up operation. (In the interval of 150ms) Engine Thermistor trouble Heater lamp trouble Control PWB trouble Thermostat trouble AC power trouble Interlock switch Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp does not turn on. • Check for disconnection of the heater lamp or the thermostat. • Check the interlock switch. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 17

H4-01

Fusing section low temperature trouble (HL2)

Details

Section Case 1

Cause

Check and remedy

H4-02

Cause

Check and remedy

The set temperature is not reached within the specified time (normally 3 min or 5 min in the curl prevention mode) after turning on the power relay. When the heater lamp is not turned off in 4 min after starting the warm-up operation. When the set value of -40°C is detected for 5 times continuously in the specified interval after completion of the warm-up operation. (In the interval of 150ms) Engine Thermistor trouble Heater lamp trouble Control PWB trouble Thermostat trouble AC power trouble Interlock switch Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp does not turn on. • Check for disconnection of the heater lamp or the thermostat. • Check the interlock switch. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

5-times continuous POD notreached JAM detection

Details

Section Case 1

Cause

Case 2

Check and remedy Cause

Case 3

L1-00

Check and remedy Cause Check and remedy

Section Case 1

Cause Check and remedy

L3-00

Cause Check and remedy

L4-01

Case 2

Scanner return is not completed within the specified time. MHPSon is not detected within 10sec after starting the mirror base unit in the return direction. Scanner Scanner unit trouble The scanner wire is disconnected. Use SIM 1-1 to check scanning operation.

Main motor lock detection

Details

Section Case 1

Scanner feed is not completed within the specified time. When MHP Soft is not detected within 2 sec after shifting the mirror base unit in the feeding direction. Scanner Scanner unit trouble The scanner wire is disconnected. Use SIM 1-1 to check scanning operation.

Scanner return trouble

Details

Section Case 1

When POD1 not-reached jam is detected 5-times continuously. POD1 jam counter is backed up and used in a print job after turning on the power. The counter is cleared when POD1 jam does not occur in a job or when the trouble is canceled. Engine The fusing jam is not canceled completely. (Jam paper remains.) Check for jam paper in the fusing section. (Winding, etc.) POD1 sensor trouble, or harness connection trouble Check the PODC1 sensor harness and installation of the fusing unit. Fusing unit installation trouble Use SIM 14 to cancel the trouble

Scanner feed trouble

Details

Fusing section low temperature trouble (HL3)

Details

Section Case 1

The set temperature is not reached within the specified time (normally 3 min or 5 min in the curl prevention mode) after turning on the power relay. When the heater lamp is not turned off in 4 min after starting the warm-up operation. When the set value of -40°C is detected for 5 times continuously in the specified interval after completion of the warm-up operation. (In the interval of 150ms) Engine Thermistor trouble Heater lamp trouble Control PWB trouble Thermostat trouble AC power trouble Interlock switch Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp does not turn on. • Check for disconnection of the heater lamp or the thermostat. • Check the interlock switch. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

H5-01

Cause Check and remedy Cause

Check and remedy

When it is detected for 3 times continuously in the interval of 500ms after ignoring the main motor drive for 600ms. Engine Main motor trouble Use SIM 25-1 to check the main motor operation. Improper disconnection of the harness between the PCU PWB and the main motor Control circuit trouble Check the harness and the connector between the PCU PWB and the main motor.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 18

L4-02

Drum motor lock detection

Details

Section Case 1

Case 2

Cause Check and remedy Cause

Check and remedy

L4-03

The motor lock signal is detected for 1.5sec during rotation of the drum motor. When the motor lock signal is detected for 3 times continuously in the interval of 500ms after 900ms of rotation start. Engine Drum motor trouble Use SIM 25-1 to check the drum motor operation.

L4-30 Details

Section Case 1

Case 2 Improper connection of the harness between the PCU PWB and the drum motor Control circuit trouble Check the harness and the connector of the PCU PWB, and the drum motor.

Fusing motor lock detection

Controller fan motor lock detection

Cause Check and remedy Cause

Check and remedy

L4-31

Section Case 1

Case 2

Cause Check and remedy Cause

Check and remedy

L4-04

Case 2

Cause Check and remedy Cause

Check and remedy

L4-06

Case 2

Case 2

The motor lock signal is detected for 1.5sec during rotation of the developing motor. When the motor lock signal is detected for 3 times continuously in the interval of 500ms after 900ms of rotation start. Engine Developing motor trouble Use SIM 6-1 to check the developing motor operation. Improper connection of the harness between the PCU PWB and the developing motor. Control circuit trouble. Check the harness and the connector between the PCU PWB and the developing motor.

Cause Check and remedy Cause

Check and remedy

Transfer belt separation motor trouble detection The transfer belt home position sensor ON/OFF is not detected within the specified time (4 sec) during operation of the transfer belt (separation, ). Engine Transfer belt separation motor trouble Use SIM 6-1 to check the transfer belt motor operation. Improper connection of the harness between the PCU PWB and the transfer belt separation motor. Control circuit trouble Check connection of the harness and the connection of the harness between the PCU PWB and the transfer belt separation motor.

Cause Check and remedy Cause

Check and remedy

L6-10

Section Case 1

Case 2

Cause Check and remedy Cause Check and remedy

L8-01

Case 2

Case 3

PCU PWB, harness connection between fan and motor trouble PCU circuit trouble Thermistor (TH_EX) trouble Check the PCU PWB, the harness between fan and motor, and the connector.

It is judged that the polygon motor lock signal of the LSU is not outputted. The polygon motor lock signal is checked in an interval of 10sec after starting the polygon motor, and it is found that the olygon motor is not rotating normally. Engine Polygon motor trouble Use SIM 61-1 to check the polygon motor operation. Disconnection or breakage of the LSU connector or the harness in the LSU Check connection of the harness and the connector. Replace the LSU.

No full wave signal

Details

Section Case 1

When the detected value of the temperature sensor (TH_EX) in the paper exit reverse unit is greater than the specified level for 2 times continuously in the interval of 30sec. When 100°C (value of 235) of the paper exit thermistor is detected for 3 times continuously. (In the interval of 100ms) Engine Fan motor trouble Use SIM 6-2 to check the fan motor operation.

Polygon motor lock detection

Details

Transfer belt separation motor trouble detection

Details

Section Case 1

Section Case 1

Developing motor lock detection

Details

Section Case 1

When it is detected for 3 times continuously in the interval of 500ms after ignoring the fusing motor drive start for 600ms. Engine Main motor trouble Use SIM 25-1 to check the fusing motor operation. Improper connection of the harness between the PCU PWB and the fusing motor Control circuit trouble Check connection of the harness and the connector between the PCU PWB and the fusing motor.

Improper connection of the harness between the controller PWB and the fan motor. Control circuit trouble Check the harness and the connector between the controller PWB and the fan motor.

Paper discharging fan trouble

Details Details

The motor lock signal is detected during rotation of the controller fan motor. The motor lock signal is detected during rotation of the HDD fan motor. Controller Fan motor trouble Use SIM 6-2 to check the fan motor operation.

Cause Check and remedy Cause Check and remedy Cause Check and remedy

The full wave signal is not detected. When the FWS signal is not varied for 120ms when supplying the power. Engine Disconnection or breakage of the PCU PWB connector or the harness in the power unit Check connection of the harness and the connector. PCU PWB trouble Replace the PCU PWB. 12V power source trouble Replace the power unit. Replace the controller connection mother board.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 19

PF-00

RIC copy inhibit command receive

Details Section Case 1

U1-01

Cause Check and remedy

Case 2

U1-02

Cause Check and remedy Cause Check and remedy

Case 2

Case 3

U2-00

Cause Check and remedy Cause Check and remedy Cause Check and remedy

Case 2

Case 3

The read value from the RTC on the MFP control PWB is abnormal such as "EE"h. Controller RTC circuit trouble Make the time setup again with the key operation and check that the time advances normally. Check the RTC circuit. Battery voltage fall Check that the battery voltage is about 2.5V or above. Battery circuit trouble Check the battery circuit.

EEPROM read/write error (MFP control)

Details Section Case 1

Section Case 1

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Case 2

Case 3

U2-12

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

EEPROM write error (without retry) EEPROM magic number error. Controller EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Insertion of EEPROM which is not initialized Use SIM 16 to cancel the U2 trouble.

Section Case 1

Case 2

Case 3

U2-22

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Case 2

Case 3

MFP control PWB EEPROM access circuit trouble Replace the MFP control PWB.

EEPROM counter area checksum error (If this error occurs, the process will retrieve for effective data within 8 blocks.) Controller EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble. MFP control PWB EEPROM access circuit trouble Replace the MFP control PWB.

SRAM memory check sum error (MFP control)

Details

Section Case 1

EEPROM counter area checksum error. (If this error occurs, the process will retrieve for effective data within 8 blocks.) Controller EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble.

Adjustment value check sum error (MFP control)

Details

RTC read error (combined use as FAX, on MFP control PWB)

Details Section Case 1

FAX backup SRAM battery voltage fall. When the battery capacity is less than the threshold value (fixed by the hardware), it is judged as an error. (Insufficient capacity of the SRAM backup battery) FAX Battery life Check that the battery voltage is about 2.5V or above. Battery circuit trouble Check the battery circuit.

Counter check sum error (MFP control)

Details

FAX battery abnormality

Details

Section Case 1

The copy inhibit command is received from the RIC (host). (By PPC communication standards.) Controller Judged by the host. Notification to the host

U2-11

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

SRAM check sum error when turning on the power. (If this error occurs, initialize the one-touch dial and the FAX soft switches.) Controller SRAM trouble Initialize the communication management table ed in the SRAM and the FAX soft switch. Since the ed data are deleted, the data again. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble. MFP control PWB EEPROM access circuit trouble Replace the MFP control PWB.

MFP control PWB EEPROM access circuit trouble Replace the MFP control PWB.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 20

U2-23

SRAM memory individual data check sum error

Details

Section Case 1

Case 2

Case 3

U2-50

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Case 2

Case 3

U2-80

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Case 2

Case 3

Details Section Case 1

Case 2

Case 3

U2-90

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Memory check sum error (Scanner)

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Check sum error for every individual data in HDD of the MFPC section when turning on the power (If this error occurs, initialize the data related to the check sum error. (One-touch, group, program, etc.)) Controller HDD write/read error Automatically initialize the data related to the check sum error by turning OFF/ON the power. Since the ed data are deleted, the data again. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble.

Section Case 1

Case 2

Case 3

U2-91

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

Section Case 1

EEPROM communication trouble (NACK detection) Retry 3 times Scanner EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Insertion of EEPROM which is not initialized Use SIM 16 to cancel the U2 trouble. Scanner PWB EEPROM access circuit trouble Replace the scanner PWB.

Case 2

Case 3

U5-30 Details Section Case 1

Scanner PWB EEPROM access circuit trouble Replace the scanner PWB.

EEPROM communication trouble (NACK detection) Retry 3 times Engine EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Insertion of EEPROM which is not initialized Use SIM 16 to cancel the U2 trouble. PCU PWB EEPROM access circuit trouble Replace the PCU PWB.

Memory check sum error (PCU)

Details MFP control PWB HDD access circuit trouble Replace the HDD. Replace the MFP control PWB.

When counter data sum error is detected. Scanner EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble.

EEPROM read/write error (PCU)

Details

EEPROM read/write error (Scanner)

Details Section Case 1

MFP control PWB EEPROM access circuit trouble Replace the MFP control PWB.

HDD section individual data check sum error (MFP control)

Details

Section Case 1

Check sum error for every individual data in SRAM of the MFPC section when turning on the power (If this error occurs, initialize the data related to the check sum error. (Communication management table, sender's information, etc.)) Controller SRAM trouble Automatically initialize the data related to the check sum error by turning OFF/ON the power. Since the ed data are deleted, the data again. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble.

U2-81

Cause Check and remedy

Cause Check and remedy Cause Check and remedy

When POF data/counter data sum error is detected. Engine EEPROM trouble Check that the EEPROM is properly installed. In the simulation to prevent against delete of the counter data/adjustment values, write down the counter/adjustment values. Control circuit runaway due to noises Use SIM 16 to cancel the U2 trouble. PCU PWB EEPROM access circuit trouble Replace the PCU PWB.

DSPF tray lift-up trouble

Cause

Check and remedy

Lift-up trouble is detected 5 times continuously. Scanner STUD/STLD trouble. STUD does not turn on within the specified time. STLD does not turn off within the specified time. Check the harness and the connector of the STUD and STLD. Lift-up trouble unit check

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 21

U5-31 Details Section Case 1

DSPF tray lift-down trouble

Cause

Check and remedy

U6-09

Cause

Check and remedy

U6-20

Cause

Check and remedy

U6-21

Cause

Case 2

Check and remedy Cause Check and remedy

U7-00

RIC communication trouble

Details

Section Case 1

Cause

Check and remedy

Communication error with RIC (By PPC communication standards) An error in the communication line test after turning on the power or canceling the simulation Controller Improper connection or disconnection of the connector and the harness. RIC control PWB trouble. Control PWB (MFP control) trouble. Malfunction caused by noises. Canceled by turning ON/OFF the power. Check the connector and the harness in the communication line.

Communication trouble with the LCC. Follows the communication protocol specifications. Communication error, timing abnormality of the communication data and the communication signal line Engine Improper connection or disconnection of the connector and the harness. Desk control PWB trouble Control PWB (PCU) trouble. Malfunction caused by noises Canceled by turning ON/OFF the power. Check the connector and the harness in the communication line.

LCC transport motor trouble

Details

Section Case 1

Section Case 1

24V power is not supplied to the LCC. (The LCC 24V power is not detected for 1 sec or longer after 1 sec from power on) LCC Improper connection or disconnection of the connector and the harness. Check the connector and the harness of the power line. LCC control PWB trouble. Power unit trouble. Check the 24V power with the power unit and the LCC control PWB.

LCC communication trouble

Details

Section Case 1

• The upper limit sensor is not turned on within 24sec from starting the liftup motor. • The encoder input is not made within 0.2sec during rotation of the liftup motor. The upper limit SW is turned on during rotation of the liftup motor. When the above trouble occurs for 3 times continuously. • For the first time and the second time, it is a tray size error and the pulls the tray. When the trouble occurs 3 time continuously that the upper limit sensor does not turn on. LCC Sensor trouble LCC control PWB trouble. Gear breakage. Lift motor trouble. Use SIM to check the sensor detection. Use SIM to check the lift motor operation. Use SIM 15 to cancel the trouble.

LCC 24V power abnormality addition

Details

LCC lift motor trouble

Details

Section Case 1

STLD does not turn off within the specified time. Scanner STUD/STLD trouble. STUD does not turn on within the specified time. STLD does not turn off within the specified time. Check the harness and the connector of the STUD and STLD. Lift-up trouble unit check

U6-22

Cause

Check and remedy

The lock detection signal is detected continuously for 1sec after delay of 1sec from start of the motor. When the motor lock detection signal is continued for 1sec after 1sec delay from starting the motor. For the first time, it is regarded as a Jam and the machine is stopped. When two errors are continued, it is regarded as a trouble. LCC Motor lock Motor RPM abnormality Overcurrent to the motor Desk control PWB trouble Use SIM 4-3 to check the transport motor operation.

MX-M700N SELF DIAG AND TROUBLE CODE 8 – 22



[9] MAINTENANCE

MX-M700N

5GTXKEG/WCN

1. Maintenance system table ✕ : Check

▲: Replace

{: Clean

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.) 250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕ ✕

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

✕ ✕

▲ ▲ ✕ ▲ ▲ ▲ ▲ ▲ ▲ ✕ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲ ▲ ▲ ▲ ✕ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲ ▲ ▲ ▲ ✕ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲ ▲ ▲ ▲ ✕ ✕ { ▲ ▲ { ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ✕ { ▲ ▲ { ▲ ▲

{ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

{ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

✕

✕

✕

✕

✕

✕

✕

✕

✕

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲ ▲ ▲ { { { ✕ ✩

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Drum peripheral section

Transfer section

Developing section

Fusing unit

Filters Paper feed section

No. 1 2

Part name Drum Cleaning blade

3 4 5 6 7 8 1 2 3 4 5 6 1 2 3 4 5 6

Cleaning brush roller Toner reception seal Side seal Drum separation pawl Sawtooth Screen grid Transfer drum gear Transfer belt Transfer roller Transfer roller collar Shaft (Conductive grease) Paper guide Developer DV seal MG holder F/R DV side seal F DV side seal R Toner bottle

7 1 2 3 4 5 6 7 8 9 10 11

Toner hopper Heat roller Pressure roller Sub heat roller Web roller Pressure connect roller CL roller CL auxiliary roller bearing Cleaning sheet desk Heat roller separation pawl Pressure roller separation pawl Thermistor (upper/lower)

12 13 14 15 16 17 18 19 20 21 1 2 1 2 3 4 5

Heat roller gear (Grease) Sub heat roller bearing CL roller bearing Web bearing Pressure connect bearing Paper guides Gears Shaft (Grease) Lower CL roller DG2 CL roller bearing Ozone filter Toner filter Pickup roller Paper feed roller Separation roller Torque limiter Shaft (Conductive grease)

✕ { ✕ ✕ {

✕ {

{

{

✕

✕ ✕ ✕ ✕ ✕

MX-M700N MAINTENANCE 9 – 1

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Maximum 1 year use (P/G No.: [43]-5) (P/G No.: [43]-29) (P/G No.: [43]-11) (P/G No.: [43]-33, [43]-35) (P/G No.: [42]-33) (P/G No.: [39]-7) (P/G No.: [39]-1) (P/G No.: [45]-25) (P/G No.: [45]-50) (P/G No.: [45]-47) (P/G No.: [45]-48) UKOG-0012QSZZ Supply when installing (P/G No.: [37]-5) (P/G No.: [36]-14) (P/G No.: [36]-13) Assembly when installing/ Replacement by when empty Clean the shutter area. (P/G No.: [48]-3) (P/G No.: [46]-24) (P/G No.: [46]-14) (P/G No.: [49]-42) (P/G No.: [49]-44) (P/G No.: [47]-46) (P/G No.: [46]-23) (P/G No.: [48]-9) (P/G No.: [47]-26) Paper dust removal is required. UKOG-0235FCZZ (P/G No.: [46]-7) (P/G No.: [47]-45) (P/G No.: [49]-4) (P/G No.: [49]-8)

UKOG-0235FCZZ (P/G No.: [47]-47) (P/G No.: [47]-45) (P/G No.: [75]-7) (P/G No.: [75]-8) (Note 1) (Note 1) (Note 1) (Note 1) UKOG-0012QSZZ

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Transport section/ paper exit reverse section/duplex section

Drive section

Picture relations Others

No. 1 2 3 4 5 6 1 2 3 4 5 6 1 1 2

Part name PS follower roller Transport rollers Transport paper guides Paper dust clean unit Discharge brush Shaft (Conductive grease) Gear (Grease) Gear (Grease) Gear (Grease) Gear (Grease) Gear (Conductive grease) Belts

✕ ✕ { ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

Sersors Reflection sensor

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

{ { { ▲ ✕ ✕ ✩ ✩ ✩ ✩ ✩ ✕ ✕ ✕ {

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

{ { { { { { { { ✩ ✕ ✕ ✕ { { { ✕ { { { {

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

UKOG-0012QSZZ UKOG-0307FCZZ UKOG-0299FCZZ UKOG-0062FCZZ UKOG-0235FCZZ UKOG-0012QSZZ

(Document scan section) 55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Scanner section

DSPF

Paper feed

Transport section Paper exit section Drive section Others

No. 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8

Part name Mirror Lens Reflector Sersors Table glass Dust-proof glass OC White standard glass Rails Drive belt Drive wire Pulley Pickup roller Paper feed roller Separation roller Torque limiter Resist roller Transport roller Exposure section (CIS unit) Paper exit roller

9 10 11

Gears (Grease) Belts Sensors

{ { { { { { { {

✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • Paper feed tray 1 and 2: 200K or 1 year • Manual paper feed/paper feed tray 3 and 4: 100K or 1 year • DSPF section: 100K or 1 year • Torque limiter: 800K (400K for manual paper feed section) * (NOTE) Paper feed section roller life When servicing, be sure to check the paper feed counters of each paper tray and replace the rollers as needed. When cleaning rollers it is advisable to use a wet cotton cloth to clean the rollers.

MX-M700N MAINTENANCE 9 – 2

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(Note 1) (Note 1) (Note 1) (Note 1)

UKOG-0299FCZZ Cleaning is air spraying

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕

{

{

{

{

{

{

{

{

(Note 2)

✕ ✕ { ✕

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

(Note 2)

✕ ✕

✕ { { ✩ ✕ ✕ { { ✩ ✕ { {

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

✕ ✕

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K)

Side LCC

Unit name Paper feed separation section

No. 1

Transport section Drive section Saddle finisher Punch unit

Others Transport section Drive section Staple process section Others

2 3 4 5 6 7 1 2 3 4 5 6

Part name Paper pickup roller/ Paper feed rollers Torque limiter Transport rollers Transport paper guides Gears Belt Sensors Transport rollers Transport paper guides Gears Belts Knurling belt Paddle

7 8

Sensors Discharge brush

✕ ✕ ✕ ✕

Stapler unit

Stitcher unit (Stapler unit for saddle)

Punch unit Staple cartridge Stitcher staple cartridge Inserter

Paper feed separation section Transport section Drive section Others

1 2 3 4 5 6 7

Paper pickup roller/ Paper feed rollers Torque limiter Transport rollers Transport paper guides Gears Belts Sensors

✕

{

{

{

{

{

{

{

{

✕ ✕ { ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕ { { ✩ ✕ ✕

✕

(Note 2) Replacement reference: For replacement, refer to each paper feed counter value. • Paper feed roller related section: 200K or 1 year • Torque limiter: 800K (Note 3) Replacement reference: For replacement, refer to the finisher paper exit counter value. • Knurling belt: 1000K • Paddle: 1000K (Note 4) Replacement reference: For replacement, refer to the inserter paper feed port counter value. • Paper feed roller related section: 150K or 1 year • Torque limiter: 400K

MX-M700N MAINTENANCE 9 – 3

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Refer to sm for LCC

Refer to sm for Finisher (Note 3) (Note 3)

Replacement reference: Replace the unit at 500K staple. Replacement reference: Replace the unit at 200K staple. Replacement reference: Replace the unit at 1000K. replacement at every 5000 pcs. replacement at every 2000 pcs. (Note 4) (Note 4)

Refer to sm for Inserter

2. Details of maintenance A. Drum peripheral section ✕ : Check

▲: Replace

{: Clean

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust as necessary.) 250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕ ✕

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

✕ ✕

▲ ▲ ✕ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ✕ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Drum peripheral section

No. 1 2 3 4 5 6 7 8

Part name Drum Cleaning blade Cleaning brush roller Toner reception seal Side seal Drum separation pawl Sawtooth Screen grid

✕ { ✕

Maximum 1 year use (P/G No.: [43]-5) (P/G No.: [43]-29) (P/G No.: [43]-11) (P/G No.: [43]-33, [43]-35) (P/G No.: [42]-33) (P/G No.: [39]-7) (P/G No.: [39]-1)

3

1

5

6

4

2

5 7

MX-M700N MAINTENANCE 9 – 4

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

8

B. Transfer section ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Transfer section

No. 1 2 3 4 5 6

Part name Transfer drum gear Transfer belt Transfer roller Transfer roller collar Shaft (Conductive grease) Paper guide

✕ {

✕ {

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [45]-25) (P/G No.: [45]-50) (P/G No.: [45]-47) (P/G No.: [45]-48) UKOG-0012QSZZ

* When cleaning the transfer belt, do not use alcohol, solvent or water. Use dry cotton cloth only.

1

5

4 2

3

5

4

MX-M700N MAINTENANCE 9 – 5

5 5

C. Developing section ✕ : Check

▲: Replace

{: Clean

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Developing section

No. 1 2 3 4 5 6

7

Part name Developer DV seal MG holder F/R DV side seal F DV side seal R Toner bottle

{

Toner hopper

{

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

{

{

{

{

{

{

{

{

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Supply when installing (P/G No.: [37]-5) (P/G No.: [36]-14) (P/G No.: [36]-13) Assembly when installing/ Replacement by when empty Clean the shutter area.

6

3 2

7

5 3 4 1

MX-M700N MAINTENANCE 9 – 6

D. Fusing unit ✕ : Check

▲: Replace

{: Clean

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust as necessary.) 250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

✕

✕

✕

✕

✕

✕

✕

✕

✕

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Fusing unit

No. 1 2 3 4 5 6 7 8 9 10 11

Part name Heat roller Pressure roller Sub heat roller Web roller Pressure connect roller CL roller CL auxiliary roller bearing Cleaning sheet desk Heat roller separation pawl Pressure roller separation pawl Thermistor (upper/lower)

12 13 14 15 16 17 18 19 20 21

Heat roller gear (Grease) Sub heat roller bearing CL roller bearing Web bearing Pressure connect bearing Paper guides Gears Shaft (Grease) Lower CL roller DG2 CL roller bearing

{

✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [48]-3) (P/G No.: [46]-24) (P/G No.: [46]-14) (P/G No.: [49]-42) (P/G No.: [49]-44) (P/G No.: [47]-46) (P/G No.: [46]-23) (P/G No.: [48]-9) (P/G No.: [47]-26) Paper dust removal is required. UKOG-0235FCZZ (P/G No.: [46]-7) (P/G No.: [47]-45) (P/G No.: [49]-4) (P/G No.: [49]-8)

UKOG-0235FCZZ (P/G No.: [47]-47) (P/G No.: [47]-45)

* When maintenance, replace fusing web roller. When used without replacement, the picture quality may be damaged because web roller end. [every 300K every 250K]

21

9 14 10

3

10

11

9 1 2 21

19 14

17 11

13

19

11 19 16

12 20 13

15 5 15

6

16

19 4

MX-M700N MAINTENANCE 9 – 7

E. Scanner section ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Scanner section

No. 1 2 3 4 5 6 7 8 9 10 11 12

Part name Mirror Lens Reflector Sersors Table glass Dust-proof glass OC White standard glass Rails Drive belt Drive wire Pulley

{ { { { { { { {

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Dry cotton cloth

Recommended cleaner Dry cotton cloth

6

7

9 7 1 1 8 10

3 1

11 12 5 2 4 11

9

12

MX-M700N MAINTENANCE 9 – 8

F. DSPF section ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name DSPF Paper feed

Transport section Paper exit section Drive section

No. 1 2 3 4 5 6 7 8

Part name Pickup roller Paper feed roller Separation roller Torque limiter Resist roller Transport roller Exposure section (CIS unit) Paper exit roller

9 10 11

Gears (Grease) Belts Sensors

Others

✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

(Note 1) (Note 1) (Note 1) (Note 1)

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

UKOG-0299FCZZ

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Clean with air

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • DSPF section: 100K or 1 year • Torque limiter: 800K

1

8

7

5

2

6

3

5

4

6

9 9 9

10

9 10 10

MX-M700N MAINTENANCE 9 – 9

G. Paper feed section ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Paper feed section

No. 1 2 3 4 5

Part name Pickup roller Paper feed roller Separation roller Torque limiter Shaft (Conductive grease)

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

✕ ✕ ✕ ✕ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(Note 1) (Note 1) (Note 1) (Note 1) UKOG-0012QSZZ

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • Paper feed tray 1 and 2: 200K or 1 year • Manual paper feed/paper feed tray 3 and 4: 100K or 1 year • Torque limiter: 800K (400K for manual paper feed section)

4 1

5 5

2 3

5

5 4 1 2 3

4 2 1 4

2 1 3

MX-M700N MAINTENANCE 9 – 10

3

H. Transport section/paper exit reverse section/duplex section ✕ : Check

▲: Replace

{: Clean

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Transport section/ paper exit reverse section/ duplex section

No. 1 2 3 4 5 6

Part name PS follower roller Transport rollers Transport paper guides Paper dust clean unit Discharge brush Shaft (Conductive grease)

✕ ✕ { ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

{ { { ▲ ✕ ✕

2 2 2 5 2

5 5 5 5 6

2

1

6 2 4

2

2 2 2

2

2

2

6

2 2 2 2

MX-M700N MAINTENANCE 9 – 11

2 2 2

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

UKOG-0012QSZZ

I. Drive section ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Drive section

No. 1 2 3 4 5 6

Part name Gear (Grease) Gear (Grease) Gear (Grease) Gear (Grease) Gear (Conductive grease) Belts

✕ ✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

UKOG-0307FCZZ UKOG-0299FCZZ UKOG-0062FCZZ UKOG-0235FCZZ UKOG-0012QSZZ

4

3 3

2 2

1 1 1 1

1 1

1

5

1

1

2 1

1 2

6

MX-M700N MAINTENANCE 9 – 12

2

J. Filters ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Filters

No. 1 2

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

Part name Ozone filter Toner filter

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [75]-7) (P/G No.: [75]-8)

1

1 2

3. Other related items A. Execution items before maintenance and servicing Item Check the developer counter value. Check the OPC drum counter value. Check the print count mode in each section and each operation mode. Check the number of paper jam troubles. Check the positions and contents of paper jams. Check the positions and contents of paper jams (DSPF section). Check the contents of troubles. Print the setting values and the adjustment values. Check the number of use of the DSPF, the scanner, the finisher, and inserter, the stapler, and the punch. Check the number of use of each paper feed section. Check the ROM version.

Simulation 22 13 22 13 22 1 22 2 22 3 22 12 22 4 22 6 22 8 22 9 22 5

B. Mandatory maintenance and service items The necessary items for maintenance are shown below. (The items marked with

No.

JOB No.

1

-

2

-

3

-

4

ADJ9

5

ADJ10

6

ADJ11

Work item

Toner concentration reference control level setting The photoconductor counter is cleared. The photoconductor rotation counter is cleared. Copy image quality adjustment (check) FAX mode print image quality adjustment (check) Scanner mode image quality adjustment (check)

Simulation

are mandatory items.)

When repairing (replacing consumable parts)/maintenance After When cleaning Periodic When When replacing the mainte replacing installing the OPC scanner nance developer drum (read) section

25-2 24-7 24-11 46-2, 9 , 10, 11, 18, 31 46-12, 13, 14, 15, 16, 45 46-21, 22, 23, 24, 25, 27

• The JOB No. indicates the title number of the adjustment item described in the chapter of the adjustments. • Refer to the details based on this number according to necessity.

MX-M700N MAINTENANCE 9 – 13

When repairing (without replacement of consumable parts)/inspecting

C. Execution items after maintenance and servicing Item The paper jam/trouble data are cleared. The use quantity counter of each paper feed section is cleared. The numbers of use of the DSPF, the scanner, the finisher, the inserter, the stapler, and the punch are cleared. The maintenance counter is cleared. Print the setting values and the adjustment values.

Simulation 24 1 24 2 24 3 24 22

4 6

MX-M700N MAINTENANCE 9 – 14

MX-M700N [10] ROM VERSION-UP

5GTXKEG/WCN

1. General A. Version-up target ROM's The version-up target ROM's are listed in the table below. The version-up procedures of the firmware of this machine is performed without disassembling the ROM from the machine. The new program files are collectively written into the ROM's. Some new programs can be written into an optional ROM. If, however, the above procedure is failed by an accident such as power interruption during the version-up procedure, use the ROM copy socket on the MFP control PWB ROM to make version-up of each ROM individually.

[Kind of ROM] Section PCU PWB

Name PCU ROM

SCN PWB

SCN ROM

MFP CONTROL PWB

BOOT ROM MAIN ROM

FAX MODEM CONTROL PWB FINISHER CONTROL PWB FINISHER SS-CONTROL PWB INSERTER CONTROL PWB

FAX ROM Finisher Control ROM Finisher SS-Control ROM Inserter Control ROM

Type Flash ROM Flash ROM Flash ROM Flash ROM Flash ROM EPROM

Capacity 8Mbit 8Mbit 128Mbit (64Mbit ✕ 2) 64Mbit (32Mbit ✕ 2) 8Mbit –

EPROM

Replaceable Replaceable Replaceable Replaceable Replaceable Replaceable Replaceable Replaceable

– EPROM

–

Replaceable

* All the Flash ROM's can be rewritten. (LAN, USB) [Block diagram]

䌌䌁䌎

䌐䌃

USB RS-232C FAX BOX MODEM CONTROL PWB Program ROM (Flash ROM)

TEL/LIU PWB

MFP CONTROL PWB

SCN PWB Program ROM (Flash ROM)

Service Socket

Program ROM (Flash ROM) Program ROM (Flash ROM)

PCU PWB

INSERTER

Program ROM (Flash ROM)

Program ROM (EPROM)

Telephone Line LCC

FINISHER FINISHER CONTROL PWB Program ROM (EPROM)

FINISHER㵘SSCONTROL PWB Program ROM (EPROM)

B. ROM version-up is required in the following cases: ROM version-up is required in the following cases: 1)

When improvement of performances is required.

2)

When installing a new spare part ROM for repair to the machine.

3)

When installing a new spare part PWB unit for repair with the ROM installed.

4)

When there is a trouble in the ROM program and it must be repaired.

MX-M700N ROM VERSION-UP 10 – 1

2. Precautions

3. Necessary items for Flash ROM version-up

A. Relationship between each ROM and version-up

• A machine with ROM to be operated

When performing ROM version-up, be sure to check the combination with the version of ROM installed in the other PWB's including optional ones. Some combinations of ROM versions may not operate the machine properly.

• A spare PCU PWB ROM, an MFP control PWB ROM (Boot, Program), a scanner control PWB ROM (Each of which is provided with the program to allow operations.) (Used when writing the program files into the ROM is failed.) • A PC operating with either of a USB or Ethernet port. • USB cable or Ethernet cable. (for connection of PC and MFP control PWB) • File2PRN.exe file (A file transfer tool for Ethernet, and USB protocols) • USB memory device (ed format in FAT (12/16) only) • Version-up program (compression) file (The SFU file for writing a program to each ROM of the PCU PWB, the MFP control PWB (boot, program), and the scanner control PWB, or the SFU file for writing all the programs collectively.)

4. Flash ROM version-up method A. Version-up procedure 1 Media Adapter

Firmware.

Firmware.

+ USB Host USB Memory

Firmware.

Firmware.sfu

(1)

Firmware update from USB memory device

3)

First you must install the firmware file (xxx.sfu) to the root of a USB jump drive. • If the firmware is in a folder, Simulation 49-01 cannot open the folder.

SIMULATION 49-1 FIRMWARE UPDATE.. ARE YOU SURE?

• Secure Jumpdrive will not work. • If the USB memory is not inserted, “INSERT A USB MEMORY DEVICE CONTAINING MFP FIRMWARE, PLEASE USE FAT (12/16) FORMAT” is displayed.

FILE1.sfu 1. YES 2. NO

• Non compliant to FAT32. If it's inserted, "CAN NOT FAT32. PLEASE USE FAT (12/16) FORMAT" is displayed. 1)

Insert the USB memory device into the main unit.

2)

Enter the 49-01 screen.Touch the key of the file to be updated. The screen transfers to the update screen. (In this screen, [FILE 1] is selected)

4)

* The number of key changes depending on the number of the file in the USB memory device inserted.

Enter the file/folder number of firmware that tries to be updated with 10-key, and press [START] key. If selecting the file, "FIRMWARE UPDATE.. ARE YOU SURE ?" is displayed. ([1]: execute, [2]: get back)

If the operation is normally completed, "COMPLETE" is displayed. When the error occurs, "ERROR" is displayed. NOTE: If the Imager locks up or loses power during the upgrade, it corrupt the firmware. If this occurs, you can rescue the firmware using the “C. Version-up procedure 3”.

SIMULATION 49-1 FIRMWARE UPDATE. SELECT FIRMUP FILE, AND PRESS START. 1. FILE1.sfu 2. FILE2.sfu 3. FILE3.sfu . . 19. >>NEXT Page

SIMULATION 49-1

0

1

FIRMWARE UPDATE.. COMPLETE FILE1.sfu

MX-M700N ROM VERSION-UP 10 – 2

B. Version-up procedure 2 NOTE1: MFP control PWB ROM DIP switch selection and Flash ROM slot To make version-up of the ROM, position of the DIP switch should be below. Front frame side

Rear frame side

DIP switch Enlarged view of DIP switch

When writing the program files collectively without disassembling the ROM's from the PWB's, and when writing the program files into an optional ROM: NOTE: The PCU ROM, the FAX ROM, and the scanner control PWB ROM must be provided with the program to operate. An empty ROM cannot be used. 1)

Connect the PC and the MFP control PWB with a I/F cable.

2)

Turn on the PC and the machine.

3)

Copy the file transfer tool and ROM program file into the same folder of the PC. (When writing with the file transfer tool File2PRN.exe) Copy the collective ROM programming file and the file transfer tool File2PRN.exe into the folder you desire on the PC.

4)

The following display is shown after a while from starting the machine.

Switch Diag mode Controller write protect

Version Check Controller PWB

CONF: *********

Switch Diag mode

Controller write protect

Diag mode

Normal mode

(Version-up procedure 2) (Version-up procedure 3)

(Version-up procedure 1)

Write protect cancel mode

Write protect mode

5)

Press MENU key several time to select an I/F to use from USB, Ethernet. (Example)

Firm Update

When shipping, the setting of controller write protect bit is cancel mode side.

From USB

NOTE 2: Operation When entering the diag mode to write into ROM, some keys on the operation and the LED are used. Necessary information including menu items and messages is displayed on the LCD .

6)

Press OK key to display the following menu.

Firm Update

[START] key is used as [OK] key, [DOCUMENT FILING] key and [FAX/IMAGE SEND] key as up/down select keys, [JOB STATUS] key as [MENU] key, and [CLEAR] key as [BACK] key. Up/Down key

BACK key

Waiting Data 7)

Transfer the program data from PC to the machine via either of USB or Ethernet.

8)

When transferring with the file transfer tool File2PRN.exe Start File2PRN.exe on the PC. Use this program to transfer the ROM program data from the PC to the main unit.

LCD

(Procedure) a)

MENU key

1)

2)

Start File2PRN.exe.

OK key

When performing version-up of the firmware by using the file transfer tool (File1PRN), the printer driver of the target model must be installed in advance. When performing version-up of the firmware by using the USB I/F, take note of the following items. Since the port for the file transfer tool (File2PRN) differs from the port for the print mode, if the port for the print mode has been already made, be careful not to mistake them. If the USB port for the print mode has been made, it is advisable to delete it in order to avoid confusion.

(Making procedures of the port for the file transfer tool (File2PRN) in the USB I/F mode) When performing version-up of the firmware by using the USB I/F, perform the following procedures to make the port in advance. 1)

Install the printer driver of the target model. In this case, set the port to other than the USB mode.

2)

Set the DIP switch to the Flash ROM version-up mode, and turn on the power.

3)

Connect the PC and the main unit with a USB cable.

4)

The PC detects the new hardware by Plug & Play function.

C:\desktop\test.sfu

b)

Click Reference button and select a ROM program to transfer. Select the target machine's port form Select Printer pull down list.

c)

Click Send button.

d)

The LED blinks and the LCD displays appropriate information as operation proceeds.

* When version-up of each ROM of the scanner control PWB is performed, the backlight of the display is turned off. This does not mean a trouble. Wait for a while.

MX-M700N ROM VERSION-UP 10 – 3

9)

When "Result: OK" is displayed after a few minutes, press Up/ Down keys to check that there is no display of "Result: NG."

6)

Press MENU key a few times to show the following display.

* When writing the program file data collectively to the machine without the FAX unit installed, "Result : NG" is displayed only to the FAX. This can be neglected.

Firm Update

***

CN Update From USB 7)

Press OK key to display the following menu.

Writing Data CN Update Waiting Data

Firm Update Waiting Data

Firm Update

***

8)

Transfer the program data from PC to the machine via either of USB or Ethernet.

9)

When transferring with the file transfer tool File2PRN.exe Start File2PRN.exe on the PC. Use this program to transfer the ROM program data from the PC to the main unit. (Procedure)

Result: OK

a)

Start File2PRN.exe.

10) Turn off the machine. 11) Turn on the machine, and use SIM 22-5 to check that each ROM version is properly upgraded.

C:\desktop\test.sfu

C. Version-up procedure 3 As for the position of the DIP switch, refer to the B. Version-up procedure 2. (MFP control PWB ROM slot) The MFP control PWB ROM is provided with three Flash ROM slots: CN4, CN5, and CN6. The boot ROM is installed to CN4, and the main ROM is installed to CN5. CN6 is an empty slot. Use this empty slot of the MFP control PWB, CN6, to copy the ROM program. When writing the program into each ROM of the PCU PWB, the FAX PWB, and the scanner control PWB individually by using an empty slot for ROM copy on the MFP control PWB ROM: * The program write target ROM installed to the empty slot for ROM copy on the MFP control PWB ROM may be empty. (No need to have the program data in it. The empty ROM can be used.) 1)

Install the write target ROM to the empty slot for ROM copy on the MFP control PWB ROM.

2)

Connect the PC and the MFP control PWB with a I/F cable.

3)

Turn on the PC and the machine.

4)

Copy the file transfer tool and ROM program file into the same folder of the PC. (When writing with the file transfer tool File2PRN.exe) Copy the collective ROM programming file and the file transfer tool File2PRN.exe into the folder you desire on the PC.

5)

b)

Click Reference button and select a ROM program to transfer.

c)

Select the target machine's port form Select Printer pull down list.

d)

Click Send button.

e)

The LED blinks and the LCD displays appropriate information as operation proceeds.

10) The LED stops flashing in a few minutes, and "Writing: OK" is displayed.

CN Update

Receiving Data

CN Update

***

Writing Data

The following display is indicated after a while. 11) Press OK key, and the following display is shown.

Version Check

CN Update ***-> CN5

CONF: *********

Writing OK ?

MX-M700N ROM VERSION-UP 10 – 4

12) "CN5" and the selection menu of slot numbers is displayed. Select "CN6" to which the target ROM is inserted to with Up/ Down keys, and press OK key.

5. Turning OFF the power during the version-up procedure

13) The LED flashes and the display is changed in the following sequence.

If the power is turned OFF during the version-up procedure, normal writing of data cannot be assured even though the machine can be booted again.

When "Result: OK" is displayed in a few minutes, press Up/ Down keys to check that there is no display of "Result: NG.".

CN Update ***-> CN5

In such a case, use the spare PCU PWB ROM, the MFP control PWB ROM (BOOT, PROGRAM), and the scanner control PWB ROM each of which includes the program to be operated, and perform the version-up procedure again. Replace with the spare PCU, the controller boot, the scanner control PWB ROM, and perform procedure "C. Version-up procedure 3" for the replaced ROM again to write data into it.

Writing Data

6. Version-up procedure flowchart

CN Update ***-> CN5

Result : OK

Write the on-board files collectively. (4.)

14) Turn off the machine. 15) Remove the ROM from the empty slot CN6 for ROM copy on the MFP control PWB ROM.

Set again.

Result: OK?

16) Install the ROM with the revised version to the PWB. 17) Turn on the machine, and use SIM 22-5 to check that the ROM version is normally upgraded. * Precautions on transferring a ROM program data with the file transfer tool File2PRN For successful transferring a ROM program data with the file transfer tool File2PRN, the following conditions should be met: • When transferring a ROM program data with the file transfer tool File2PRN, the destination machine must be configured as a printer.

NO YES

NO

YES

• The PC must have an appropriate printer driver installed and configured with an I/F port to use.

D. Countermeasures against "Result: NG”

Setting mistake? (6.)

NG is BOOT? NO

YES

Factors of "Result: NG"

NG is SCAN FAX PCU,MAIN?

The following cases may be factors of "Result: NG." * The DIP switch for write protect is not set properly. * The FAX cable is not connected. (NG for FAX) * ROM defect (Very rare case)

MX-M700N ROM VERSION-UP 10 – 5

NO

YES

Update completed

YES

NO

Booted normally?

Write the on-board files collectively. (4.)

Remove the BOOT Flash ROM and replace it with a spare one. (If there is any NG Flash ROM, replace it, too.)

YES Write with an empty socket. (5.)

Update completed

Result: OK?

NO

YES

Result: OK?

NO

Update completed

If the Flash ROM itself is defective, replace it with a new one and try again.

NO

YES

Booted normally?

Write the on-board files collectively. (4.)

Remove the Flash ROM and replace it with a spare.

YES Result: OK? Write with the empty socket. (6.)

Result: OK?

NO

Update completed

YES

Update completed

If the Flash ROM itself is defective, replace it with a new one and try again.

MX-M700N ROM VERSION-UP 10 – 6

NO

Write the on-board files collectively. (4.)

YES

Update completed

Result: OK?

NO If the Flash ROM itself is defective, replace it with a new one and try again.

MX-M700N ROM VERSION-UP 10 – 7

MX-M700N ELECTRICAL SECTION 11 – 1

SRRBC

SRRC

STRBC

STRC

SPOD

SOCD

SPLS1

SPLS2

SPWS

WH-SCN1

Standard : JPN OPTION : EX100/EX200

SPFFAN

STLD

SPED2

SPPD3

SPPD4

OCSW

ORSLED

MHPS

MIM

SCNcnt PWB

FAX DC/PS (OPTI ON)

FAX PWB

WH-SW

MRSW

MSW

HL3

HL2

AC PWB

WH-DSK2

WH-DSK1

WH PWB

AC IN

FM-DC2

FM-DC1

SUB P/S PWB

RTH3

RTH2

RTH1

WEB_END

WEBM

MFP CONTROL PWB

FUSING un

HL1

FM-CTL

PCS

CRUM

TM1

TFSD

HOPPER un

HUS-DV

TCS

DEVELOPER un

PPD

PS un PSBC

TH-CL

INTPWB

PSPS

DMS DL

T2S PWB

T2PUS T2LUM T2SPD

T2PFC

T1S PWB

T1SPD

T1PFC T1PUS T1LUM

T1PPD

HPLS

MPRD1 MPRD2 HPFC

LPPD

MPFD2

MFPUS MPED MPFGS MPFD1

MPFC

MPFPWS

MTOP2

MTOP1

MPLD2

MPLD1

DSW-R

DSWDSK DSKPFC1 DSKPFC2

TANSET

HUS-TC

TLS

TM2 HV

FBPWB

TBPWB

AI NPD DSWD DGS

APPD2 PFD2 THPS2 TURM HVRPWB

ADUM1 DSW-L APPD1

ADUM2

LEFT DOOR un

MANUAL PAPER FEED un

PNC PROCESS un

DSW-F

M2SS PWB M2SPD

M2LUM

M2PFC

M1SPD

M1SS PWB

M1PWS

M1LUM

M1PFC

M2LUD M2PFD

M2PUS M2PED

PAPER FEED un 2

M1LUD M1PFD

FM-HDD

MOTHER PWB

Standard : JPN OPTION : EX100/EX200

DC/PS1

HDD

(OPTION)

AUDITOR

PNC

(OPTION)

COIN VENDER

(OPTION)

STMP

CL

CCDPWB

ORSPD

M1PUS M1PED

PAPER FEED un 1

PCU PWB

DELIVERY un

WH-LCC

TH-EX

INSRTR

FIN

FM-DV RRC

MM

FUM

DVM

DM

TH-RA

INTPWB

FM-R3

FM-R2

FM-R1

PGM

BD

FM-BU

FM-BR

FM-U2

FM-BL

FM-E3

FM-E1 FM-E2

INTPWB

FM-U4

FM-U3

FM-U1

POD3

POD2

POD1

POM2

POM1

VPM

TRM

(OPTION)

LD PWB

LSU un

(OPTION) LCC

DRIVER PWB

1

[11] ELECTRICAL SECTION

STRRBC

SPF PWB

SLUM

SCN JNT PWB

BUZZER

OPE PWB

ENGINE



STRRC

SPPD2

STUD

SPPD1

SCOV

SPED1

SPFC

SPSM

SPFM

CISun

CIScnt PWB

INV PWB

TOUCH

DSPF un

LVDS PWB

LCD BACK LIGHT

SCANNER OP un

MX-M700N

5GTXKEG/WCN

1. Block diagram

A. Overall block diagram

B. MFP controller

Flash DIMM (16MB x1 8MB x2) 䍃BOOT 䍃MAIN 䍃OPTION

MEMD[ 31:0] Gate

SysAD[54:34] LA[22:2]

Buffer

U I/F

Mask DIMM (32MB) PS Kanji

MAA[12:0]

Memory I/F

FAX I/F

SysAD[31:0]

Address Buffer

SysAD[63:0]

SDRAM ON BOARD (128MB)

MD[63:0]

SDRAM DIMM(168pin) 128/256MB

RTC

LDATA[15:0]

SYSTEM Controller

SRAM (4Mbit)

232C Driver

EEPROM (64Kbit)

I/O G/A (ASIC1)

LD

TD62503F TD62503F

IOD[15:0]

Scanner I/F

D/A Converter LCD Controller

PCI Bus PCI I/F SDRAM (32MB)

USB HOST I/F

IDE I/F

Soft-NIC

USB Controller

ICU ASIC PM1075

IDE Controller

LD (EPM3064A)

USB HOST Controller

USB I/F PM2060i (For 55/62ppm) PM-22A

PM-22B

MX-M700N ELECTRICAL SECTION 11 – 2

Engine I/F

Dracula㸉

RIC I/F

IOA[17:0]

Address Buffer

Local I/F

Data Gate

SysCMD[8:0]

U RM7065C600MHz

Analog output

UART (TXD, RXD) (LCC, FINISHER, INSERTER)

Fusing thermistor Temperature/humidity sensor Paper width detection AV voltage monitor Process/developing tank signal

Anaput

Power switch monitor ȪMSW-MON)

DS

DC power

FW

1

COMPARATOR

+24V1 +12V2 +5V2 +3.3V1

OP-AMP

MX-M700N ELECTRICAL SECTION 11 – 3

ANALOG-OUT

+5VSpower

Fusing Ӳ control signal

DRIVER PWB

DACs

S-RAM

FLASH ROM

/PCU_RESET

UART

U

UART(TXD, RXD)

POF

XTAL

PCU_RESET System CLOCK

RESET

DATA, CLOCK UART (DTR, DSR)

EEPROM

+5VS power

OSC

FPGA

1 2

COMPARATOR

+24V 4 (Interlock line)

High voltage control signal (Enable, PWM output)

High voltage trouble detection

4 +24V (Interlock line) +24V1

DRIVE CIRCUIT

3

Thermistor open detection

2

Fusing control signal

Door open detection (Interlock switch)

PGM clock, control signal

+5VLD

COMPARATOR REGURATORIC

BD, control signal, VIDEO signal

Fusing control signal

FWS

Detect control Mode select signal CLOCK

I/O ASIC2

I/O ASIC1

+38V monitor

INT_PR (relay)

BUP_PR (relay)

4

SUBDS

+24V (Interlock line)

+12VS power FW-SUB

BUCKUP CIRCUIT

4 +24V (Interlock line)

+12VS power Oscillator (LSU, MOTOR, PWM)

Anaput (Fusing thermistor)

COMPARATOR

3

DATA,CLOCK

CLOCK

CLOCK

Thermistor open detection High temperature protection

Fusing heater control

PMC GATE-ARRAY

DATA (D0 to D15)

ADDRESS (A0 to A20)

SUBDS

Fusing heater relay control

+24V(Interlock line) Ӵ

Stepping motor control signal

OP-AMP

OP-AMP

ANALOG SWITCH IC

Analog power (Vref )

FWS

DCCNT (Power relay control)

+12V2

PCU

HSYNC, PAGE

RESET

+12VS power monitor

FLASH ROM write control (FWP)

/PCU_RESET

PROFF_CNT, PRON_FAX

CLOCK

VIDEO signal

Option detection

CONTROLLER

RES (LCC, FINISHER, INSERTER)

UART (DTR, DSR) (LCC, FINISHER, INSERTER)

Clutch, solenoid, relay, Brushless motor, LED, PWM output, synchronous motor

Sensor input

Sensor input

Brush motor Synchronous motor

HV un

Clutch, solenoid, relay, Brushless motor, PWM output (FAN)

DOOR SWITCH

Sensor input (PPD, ADU, DV signal) Sensor input

LSU

AC PWB

C. PCU Circuit BLOCK

MX-M700N ELECTRICAL SECTION 11 – 4

Mirror motor

Document detection light reception Touch X Touch Y SPF document width detection LCD backlight TH

Anaput

CIScnt

+12V2

OP-AMP

DRIVE CIRCUIT

RES_CCD2

UART

Analog power (Vref)

Mirror motor control signal

IMAGE DATA CIS(LVDS)

RES _CCD1

2

S-RAM

FLASH ROM

UART

U

UART

/RES_SCN

RES_MFP KEYIN

1

RES_U

DATA, CLOCK

EEPROM 4Kbit

RES_SC/Nin

Sensor input

3

DATA (D0 to D15)

STMP

ADDRESS (A0 to A20)

FLASH ROM write control (FWP)

XTAL

Clutch, solenoid

SPF PWB

FLASH ROM write voltage (VCCW) /RES_SCNin

UART

WAKEUP Stepping motor control signal

CCD

POF_SCN Clutch, solenoid

IMAGEDATACCDȪLVDSȫ

STAMP

SCNcnt

2

3

Clutch, solenoid WAKEUP

EEPROM 64Kbit

I/O G/A

XTAL

SLEEP

FRDY

CCFT

1

KEYIN

SPED2, OCSW

/ORSLED

SEG

/F

LCDDATAȪLVDSȫ

LED lighting circuit

Buffer

CONTROLLER LCD

Sensor input

/CL, FAN

MFPOPE

LVDSPWB

CCFT

INV PWB

D. Scan Circuit BLOCK

MX-M700N ELECTRICAL SECTION 11 – 5

A

B

C

D

AC IN

+24V

8

WHPR2/

WH-SW

WH-L

L1

N1

L1

MAIN POWER SW

WH-L

WH-N

RY1

7

NO

NC

WH-N

WH PWB

SCN unit

NR101

NF

WH_LCC

10W

WH2_DESK

10W

WH1_DESK

18W

WH1_SCN

7W

T2AH250V

F102

Switching POWER

T2AH250V

F101

(POWER SECTION)

SUB POWER

7

WH HEATER SET: OPTION

F3 T2.0AH250V

WH-N

no-mounting

N

L

VR1

A1

20A/250V

F1

AC PWB

8

HLV

RL1/RL2

6

LCC

DESK

RY3

POWER SW

BUP_PR

T4A 125V NR1

F1

N2

L2

+12V

RL3

+24V

to PCU

Transformer

+12VS(from SUB POWER)

N1

L1

N1

L1

+12VS

FW_sub

FAX POWER

N1

6

5

+12VL

N2

L2

5

F5

FUSING UNIT

VR3

VR2

HL1

T2

T1

HL circuit

G

TD1

SUB POWER

A2

T2.5AH250V

to Controller

FAX MAIN őŐŘņœ

DR

MSWN

MSWL

6

4

4

L

#187

2 GND

1

HLCNT1

N2H

N2H

no-mounting

SSR1

#187

#187

no-mounting

4

L2H

L2H

G

TD2

HL2

T2

T1

N2D

L2D

3

6

4

ΡυͺȜ

SSR2

HLPR/

+24VPR

2 GND

1

NR1

F1 15A 250V

N/F

HLCNT2

MSW detection circuit

no-mounting

3

G

TD3

HL3

T2

T1

N/F

SSR3

RY2

L

HLCNT3

RY1

+5V1

2

#187

no-mounting

170Ɏ AC120V-15A/AC240V-10A

170Ɏ AC120V-15A/AC240V-10A

HLTS1

FW generating circuit

DS

1

1

Voltage generation (24V1 – 7 , 3.3V 5V2 , 12V2 38V1 – 3)

150Ɏ AC120V-15A/AC240V-10A HLTS2

2 GND

1

DCCNT

RL1

NR2

Voltage generation (12V1 , 5V1)

T3.15AH 250V

F2

T5AH 250V

F3

HLTS3

6

4

2

A

B

C

D

2. Power line chart

A. AC POWER LINE DIAGRAM (100V)

MX-M700N ELECTRICAL SECTION 11 – 6

A

B

C

D

AC IN

+24V

WH-L

8

L1

T2AH250V

F4 T2.0AH250V

N1

L1

WH-L

RY1

7

NO

NC WH-N

WH PWB

F102

7W

WH_LCC

10W

WH2_DESK

10W

WH1_DESK

18W

WH1_SCN

SCN unit

NR101 T2AH250V

NF

Switching POWER

F101

(POWER SECTION)

SUB POWER

MAIN POWER SW

7

WH HEATER SET: OPTION

WH-N

WH-N

F3 T2.0AH250V

N

no-mounting

WHPR2/

WH-SW

F2

10AH240V

L

VR1

A1

10AH240V

F1

AC PWB

8

HLV

N1

L1

RL1/RL2

6

LCC

DESK

RY2

RY1

POWER SW

BUP_PR

T2AH250V NR1

F1

to PCU

+12V

RL3

N2

L2

+24V

Transformer

+12VS(from SUB POWER)

N1

L1

+12VS

FW_sub

FAX POWER

N1

6

5

+12VL

N2

L2

5

F5

FUSING UNIT

A2

VR3

HL1

T2

T1

HL PWB

G

TD1

6

4

VR2

SUB POWER

T2.5AH250V

to Controller

FAX MAIN POWER

DR

MSWN

MSWL

4

SSR1

#187

HLCNT1

4

N2H

N2H

2 GND

1

#187

no-mounting

4

L2H

L2H

G

TD2

HL2

T2

T1

N2D

L2D

3

6

SSR2

HLPR/

+24VPR

2 GND

1

NR1

F1 T8AH 250V

N/F

HLCNT2

MSW detection circuit

no-mounting

3

G

TD3

HL3

T2

T1

N/F

2

HLTS1

HLTS2

HLCNT3

DS

1

170ûC AC120V-15A/AC240V-10A

170ûC AC120V-15A/AC240V-10A

1

Voltage generation (24V1 – 7 , 3.3V 5V2 , 12V2 38V1 – 3)

FW generating circuit

150ûC AC120V-15A/AC240V-10A

2 GND

1

RY1

DCCNT

SSR3

NR2

Voltage generation (12V1 , 5V1)

T3.15AH 250V +5V1 RL1

F2

T5AH 250V

F3

HLTS3

6

4

2

A

B

C

D

B. AC POWER LINE DIAGRAM (200V)

D

C

B

A

1

F202

F206 6.3A/250V

F205 6.3A/250V

6.3A/250V

F204

6.3A/250V

F203

6.3A/250V

DC Power Supply UN

6.3A/250V

F201

6.3A/250V

+24V2 GND1 +5V2 GND2

+12V1 GND2 +5V1 GND2

FW

+24V1 GND1 +12V1 GND2 +12V2 GND2 +5V2 GND2 +3.3V GND2

GND1

+38V

2

+24V6 GND1 +5V2 GND2

+24V5 GND1

+24V4 GND1 +5V2 GND2

INTPR

INSERTER

LCC

DRIVER PWB

+5VS

+38V

O 3

DSW-L

DSW-F

HDD

DVM

DSW-R

+5VS +12V1 GND2 +5V1 GND2

WEBM TM1 TM2

MOTHER

+12V1 GND2 +5V-HDD GND2

+24V1

+24VDSW

+24VPR

FW_SUB

+24VPR

+12VS

DM

N

L

MFP CNT

HLPR\

RELAY

RELAY

+24V3 GND1 +12V2 GND2 +5V2 GND2

Option

+24V5 GND1 2I

3

FIN

O3

+5V

+24V5 REGULATER

O3

2I

REGULATER

+5V2

SCNPWB

+24V3 GND1

+3.3V GND2

+24V3 GND1

2I

FIN

+5V

+24V5

REGULATER

O3

Inverter

MIM Xe Lamp

DC-DC

DC-DC

DC-DC

4

Option (FIN only)

+24V5 GND1

+3.3V

+24V3 GND1 +12V2 GND2 +5V2 GND2

+24V1 TRANS

TRANS

TRANS

TRANS

LSU

HL1

HL2

HL3

+1.3V

+2.5V

+3.3V

+5V2

Main HVU

LD

PM

DSW-F_HV

+5V2 GND2 +5VLD GND2

+24V1 GND1

(100V) SUB Power Supply UN

FUM

4

POM1 POM2 1 2 TRM VPM

Driver

Driver

Driver

2I

3

MM

REGULATER

Option

GND1

+24V2

+24V1

+24V1

+24V1

PCU PWB

+12VS

RELAY

AC PWB

GND1

1G

F208

2

1G

MX-M700N ELECTRICAL SECTION 11 – 7 1G

+5VS 1G

+12VS

5

5

DVBS

THV

GB

MHV

N

L

TRANS

TRANS

HLPR\

+12V2 GND2 +5V2 GND2 +3.3V GND2

+24V3 GND1 +12V2 GND2 +5V2 GND2 +3.3V GND2

+24V3 GND1 +5V2 GND2

+24V3 GND1

+5V1 GND2 +5V2 GND2 +3.3V GND2

RELAY

SUB Power Supply UN

2I

O3

REGULATER

6

2I

O3

REGULATER

CCD

CIS

SPF

LVDS

OPE

Transfer Bias PWB

DSW-L_HV

FW_SUB

+24VPR

+12VS

(200V)

6

1G

+24VPR 1G

1

+5V2

+2.5V

+5V2

+2.5V

+24V3 GND1

+/-BS

+24V3 GND1

Inverter

7

SLUM

SPFM

SPSM

LCD BACKLIGHT

HL1

HL2

HL3

7

8

8

D

C

B

A

C. DC POWER LINE DIAGRAM

ORSPD

CCFT

/YL XH YH /XL

4 3 2 1

S6B-PH-K-S PDSEL0 1 PDSEL1 2 PDSEL2 3 5V2 4 PD 5 GND 6

CN2 53259-0417 1 CCFT+ 2 NC 3 NC 4 /CCFT

TOUCH

LCD

BR LB PL BL BR GY

INV PWB

CN1 S3B-PH-K-S(LF) /CCFT 3 2 GND +24V 1

FFC-4Pin

FFC-13Pin

BR LB PL BL BR GY

CN4 52271-0469 /YL XH YH /XL

CN2 52271-1379 DISP YD LP +3.3V GND M D0 D1 D2 D3 +24V VEE

LVDS PWB

MX-M700N ELECTRICAL SECTION 11 – 8

Option

STMP

CL1

CCDFAN

CN1 52610-2471 1 GND 2 5V1 3 /BZR 4 NC 5 NC 6 GND 7 GND 8 GND 9 /F3 /F2 10 /F1 11 /F0 12 SEG2 13 14 SEG1 15 SEG0 /KEYIN 16 5V2 17 GND 18 PD 19 20 5V2 PDSEL2 21 PDSEL1 22 PDSEL0 23 GND 24

CN1 52271-3079 30 XH 29 /YL 28 /XL 27 YH 26 /CCFT 25 24V3 24 GND 23 TH 22 GND 21 lcdD320 lcdD3+ 19 lcdD218 lcdD2+ 17 lcdD116 lcdD1+ lcdD015 lcdD0+ 14 13 VCONT 3.3V3 12 LCD_DISP 11 GND 10 LCD_- 9 LCD_+ 8 7 GND LCD_LP- 6 LCD_LP+ 5 lcdM4 lcdM+ 3 LCD_YD- 2 LCD_YD+ 1

1 2

SLD5R-1(FCI) 1 GND 2 GND 3 /CL1 4 24V3 5 24V3

12V2 CCDFAN

CCD PWB

179228-4 1 2 3 4

FFC-5Pin

FFC-40Pin

FFC-24Pin

FFC-30Pin

175694-4 + 179228-4(AMP) RD 4 24V3 BR 3 /STMPS LB 2 /STSET GY 1 GND

CN1 IL-FPR-40S-VF-E1500 1 GND 1 DATA3+ 2 1 DATA3- 3 1 DATA2+ 4 1 DATA2- 5 1 DATA1+ 6 1 DATA1- 7 1 DATA0+ 8 1 DATA0- 9 10 GND 11 1 CLK+ 12 1 CLK13 GND /1 DBL+ 14 /1 DBL- 15 16 GND FRMCCD1 17 18 /PAGE1 CLKCCD1 19 ADDCCD1 20 TXDCCD1 21 RXDCCD1 22 RESCCD1 23 24 GND 25 3. 3V3 26 3. 3V3 27 GND 28 5V2 29 5V2 30 5V2 31 5V2 32 5V2 33 5V2 34 5V2 35 5V2 36 GND 37 12V2 38 12V2 39 GND 40 GND

MFP OPE PWB

CN2 B6B-PH-SM4-TB(LF)(SN) PDSEL0 PDSEL1 PDSEL2 5V2 PD GND

CN201 BM12B-SRSS-TB 1 IMG DOUT1 0 2 IMG DOUT1 1 3 IMG DOUT1 2 4 IMG DOUT1 3 5 IMG DOUT1 4 6 IMG DOUT1 5 7 IMG DOUT1 6 8 IMG DOUT1 7 9 IMG AREA1 10 GND 11 AD CLK 12 GND

1 2 3 4 5 6

CN3 S3B-PH-SM4-TB(LF) 1 /CCFT 2 GND 3 +24V

1 2 3 4

1 2 3 4 5 6 7 8 9 10 11 12 13

CN6

CN3 SLD5S-1(FCI) 1 GND 2 GND 3 /CL1 4 24V3 5 24V3 CN7 B4B-PH-K-S 1 24V3 2 /STMPS 3 /STSET 4 GND

CN1 B2B-PH-K-S 1 12V2 2 CCDFAN

CN4 TX25-100P-LT-H1 1 GND 2 GND 3 /1 DBL/1 DBL+ 4 5 1 CLK6 1 CLK+ 1 DATA0- 7 1 DATA0+ 8 1 DATA1- 9 1 DATA1+ 10 1 DATA2- 11 1 DATA2+ 12 1 DATA3- 13 1 DATA3+ 14 15 GND 16 GND /CCDFAN 17 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 FRM CCD1 61 CLK CCD1 62 TXD CCD1 63 RES CCD1 64 RXD CCD1 65 ADD CCD1 66 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 GND 81 /F2 82 GND 83 /F3 84 GND 85 /BZR 86 GND 87 5V1 88 lcdDIS 89 3.3V3 90 GND 91 LCD VEE 92 TH 93 /CCFT 94 /YL 95 XH 96 24V3 97 24V3 98 GND 99 100 GND

SCN JNT PWB

CN2 IL-FPR-40S-VF-E1500 40 GND 39 1 DATA3+ 38 1 DATA337 1 DATA2+ 36 1 DATA235 1 DATA1+ 34 1 DATA133 1 DATA0+ 32 1 DATA031 GND 30 1 CLK+ 29 1 CLK28 GND 27 /1 DBL+ 26 /1 DBL25 GND 24 FRMCCD1 23 /PAGE1 22 CLKCCD1 21 ADDCCD1 20 TXDCCD1 19 RXDCCD1 18 RESCCD1 17 GND 16 3. 3V3 15 3. 3V3 14 GND 13 5V2 12 5V2 11 5V2 10 5V2 9 5V2 8 5V2 7 5V2 6 5V2 5 GND 4 12V2 3 12V2 2 GND 1 GND

CN5 T24FAZ-SMT-TF 24 GND 23 5V1 22 /BZR 21 NC 20 NC 19 GND 18 GND 17 GND 16 /F3 15 /F2 14 /F1 13 /F0 12 SEG2 11 SEG1 10 SEG0 9 /KEYIN 8 5V2 7 GND 6 PD 5 5V2 4 PDSEL2 3 PDSEL1 2 PDSEL0 1 GND

30FMZ-BT 1 XH 2 /YL 3 /XL 4 YH 5 /CCFT 6 24V3 7 GND 8 TH 9 GND 10 lcdD311 lcdD3+ 12 lcdD213 lcdD2+ 14 lcdD115 lcdD1+ 16 lcdD017 lcdD0+ 18 LCD-VEE 19 3.3V3 20 lcdDIS 21 GND 22 lcd223 lcd2+ 24 GND 25 lcd126 lcd1+ 27 lcdM28 lcdM+ 29 lcdS30 lcdS+

SCN cnt PWB

CN1 TX24-100R-LT-H1 1 GND 2 GND 3 / 1 DBL4 / 1 DBL+ 5 1 CLK6 1 CLK+ 7 1 DATA08 1 DATA0+ 9 1 DATA110 1 DATA1+ 11 1 DATA212 1 DATA2+ 13 1 DATA314 1 DATA3+ 15 GND 16 GND 17 /CCDFAN 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /X L 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 61 FRM CCD1 62 CLK CCD1 63 TXD CCD1 64 RES CCD1 65 RXD CCD1 66 ADD CCD1 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 81 GND 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 88 5V1 89 lcdDIS 90 3.3V3 91 GND 92 LCD VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND 1 2 3 4 5 6

BL GY LB RD BR LB

RD GY PL GY BL GY

CN7 S6B-PH-K-R 1 MIMA 2 MIMB 3 /MIMA 4 /MIMB 5 24V3 6 24V3

RD BL YL OR BK WH

CN6 B3B-PH-K-S LB 1 MHPS GY 2 GND BL 3 5V2

CN3 B6B-PH-K-S 1 5V1 2 GND OCSW 3 24V3 4 5 /LED0 /LED1 6

CN8 B6PS-VH 24V3 GND 12V2 GND 5V2 GND

CN9 8AL068S-305C3 1 GND 2 DATA1- 2 2 DATA0- 3 4 GND 5 2 CLK+ 6 /2_DBL7 GND /TXDSCN 8 DTRSCN 9 VCCWSCN 10 WAKEUP 11 /RESMFP 12 LCD-VEE 13 14 FRDY 15 SLEEP 16 GND 17 GND 18 lcdD319 lcdD220 lcdD121 lcdD 022 lcd223 lcd124 lcdM25 lcdS26 GND 1 DATA3- 27 1 DATA2- 28 1 DATA1- 29 1 DATA0- 30 31 GND 32 1 CLK+ 33 /1 DBL34 GND 35 GND 2 DATA1+ 36 2 DATA0+ 37 38 2 CLK39 GND /2 DBL+ 40 41 GND 42 GND POF SCN 43 /RES SCN 44 /RXD SCN 45 /DSR SCN 46 /SCNSET 47 48 lcdDIS 49 5V1 50 GND 51 GND 52 lcdD3+ 53 lcdD2+ 54 lcdD1+ 55 lcdD0+ 56 lcd2+ 57 lcd1+ 58 lcdM+ 59 lcdS+ 60 GND 1 DATA3+ 61 1 DATA2+ 62 1 DATA1+ 63 1 DATA0+ 64 65 1 CLK66 GND /1 DBL+ 67 68 GND

SRA-21T-4

OCSW

MFP_Power

ELR-02VF ELP-02V 2 WH-N(SCN) 2 1 WH-L(SCN) 1

EHR-3 BL 1 5V2 GY 2 GND LB 3 MHPS

MIM

MHPS

ORSLED

EHR-3 BL 1 5V1 GY 2 GND LB 3 OCSW

WH BK

WH WH

Standard:JPN Option:EX100/EX200

MFP_Signal

WH-SCN1

ENGINE

CN6 VHR-10N BL 3 5V2 GY 4 GND

CN5 VHR-4N PL 3 12V2 GY 4 GND

CN3 VHR-9N RD 5 24V3 GY 6 GND

ELP-02V BK 1 WH-L(SCN) WH 2 WH-N(SCN)

DS PWB

MOTHER PWB

CN4 8AL068S-305C3 1 GND 2 2 DATA13 2 DATA04 GND 5 2 CLK+ 6 /2_DBL7 GND 8 /TXD SCN 9 DTR SCN 10 VCCW SCN 11 WAKEUP 12 /RESMFP 13 LCD-VEE 14 FRDY 15 SLEEP 16 GND 17 GND 18 lcdD319 lcdD220 lcdD121 lcdD022 lcd223 lcd124 lcdM25 lcdS26 GND 27 1 DATA328 1 DATA229 1 DATA130 1 DATA031 GND 32 1 CLK+ 33 /1 DBL34 GND 35 GND 36 2 DATA1+ 37 2 DATA0+ 38 2 CLK39 GND 40 /2 DBL+ 41 GND 42 GND 43 POF SCN 44 /RES SCN 45 /RXD SCN 46 /DSR SCN 47 /SCNSET 48 lcdDIS 49 5V1 50 GND 51 GND 52 lcdD3+ 53 lcdD2+ 54 lcdD1+ 55 lcdD0+ 56 lcd2+ 57 lcd1+ 58 lcdM+ 59 lcdS+ 60 GND 61 1 DATA3+ 62 1 DATA2+ 63 1 DATA1+ 64 1 DATA0+ 65 1 CLK66 GND 67 /1 DBL+ 68 GND

3. Actual wiring chart

A. SCN unit section

MX-M700N ELECTRICAL SECTION 11 – 9

SPLS1

B3P-PH-K-S BL 5V2 3 BR SPLS1 2 GY GND 1

SMP-05V-NC SMR-05V-N BR 1 OUT /SLUMB 1 BR 2 OUT /SLUMA 2 BR 3 OUT SLUMB 3 BR 4 OUT SLUMA 4 RD 5 5 24V3

SPOD

SOCD

B3P-PH-K-S BR SPOD 3 GY GND 2 BL 5VPOD 1

B3P-PH-K-S BL 5V2 3 BR SOCD 2 GY GND 1

PHNR-9-H +BU9P-TR-P-H OR 1 VAREF BR 2 SPWS GY 3 GND BL 4 5V2 BR 5 SPLS2 GY 6 GND BL 7 5V2 BR 8 SPLS1 GY 9 GND

PHNR-3-H PHNR-3-H +BU3P-TR-P-H BR 1 /SRRBC 3 2 N.C 2 RD 1 3 24V3

PHNR-2-H PHNR-2-H +BU2P-TR-P-H BR 1 /SRRC 2 RD 2 24V3 1

PHNR-3-H PHNR-3-H +BU3P-TR-P-H BR 1 /STRBC 3 2 N.C 2 RD 3 24V3 1

PHNR-2-H PHNR-2-H +BU2P-TR-P-H BR 1 /STRC 2 RD 2 24V3 1

PHNR-3-H PHNR-3-H +BU3P-TR-P-H RD 1 24V3 3 BR 2 SPFFAN 2 GY 3 GND 1

PHNR-9-H OR 9 BR 8 GY 7 BL 6 BR 5 GY 4 BL 3 BR 2 GY 1

SMR-12V-N SMP-12V-NC BL BL 1 5V2 1 BR BR 2 2 SPPD4 GY GY 3 3 GND BL BL 4 4 5V2 BR BR 5 5 SPPD3 GY GY 6 6 GND BL BL 7 7 5V1 BR BR 8 8 SPED2 GY GY 9 9 GND BL BL 10 10 5V2 BR BR 11 11 STLD GY GY 12 12 GND

SLUM

PHNR-3-H +BU3P-TR-P-H PHNR-3-H OR 3 1 VAREF BR 2 SPWS 2 GY 3 GND 1

BK

BK

BK BK

BK

BK

BK BK

B3P-PH-K-S BL 5V2 3 BR SPLS2 2 GY GND 1

BL BR GY

SPLS2

SPWS

SRRBC

SRRC

STRBC

STRC

RD YL BK

B3P-PH-K-S BL 5V2 3 BR STLD 2 GY GND 1

B3P-PH-K-S BL 5V1 3 BR SPED2 2 GY GND 1

B3P-PH-K-S BL 5V2 3 BR SPPD3 2 GY GND 1

SPFFAN

STLD

SPPD2

SPPD3

SPPD4

B3P-PH-K-S BL 5V2 3 BR SPPD4 2 GY GND 1

YL BR OR BK RD

STUD

SPED1

SPPD1

SCOV

SPFC

PHNR-2-H PHNR-2-H +BU2P-TR-P-H BR 1 /SPFC 2 RD 2 24V3 1

B3P-PH-K-S BL 5V2 3 BR STUD 2 GY GND 1

B3P-PH-K-S BL 3 5V2 BR SPED1 2 GY 1 GND

B3P-PH-K-S BL 3 5V2 BR 2 SPPD1 GY 1 GND

B3P-PH-K-S BL 3 5V2 BR 2 SCOV GY 1 GND

BK BK

CN5 B14B-PH-K-S 1 /SPFC 2 24V3 3 SCOV 4 GND 5 SPPD1 6 GND 7 SPED1 8 GND 9 STUD 10 GND 11 5V2 12 5V2 13 5V2 14 5V2

CISun

5V2

CN1 SD7 FF3-35-R15 GND SD6 GND SD5 GND SD4 GND SD3 GND SD2 GND SD1 GND SD0 GND /LST GND SCLK GND LD GND DATA GND CLK GND LGATE GND SCN GND VDS GND VAS GND VLED

CN3 B34B-PHDSS-B BR 1 OUT /SLUMB BR 2 /STRC BR 3 OUT /SLUMA BR 4 /STRBC BR 5 OUT_SLUMB BR 6 /SRRBC BR 7 OUT_SLUMA BR 8 /SRRC GY 9 GND GY 10 GND GY 11 GND GY 12 GND GY 13 GND GY 14 GND GY 15 GND GY 16 GND BL 17 5VPOD GY 18 GND BL 19 5V2 GY 20 GND BL 21 5V2 BL 22 5V2 BL 23 5V2 BL 24 5V2 OR 25 VAREF 26 N.C RD 27 24V3_SRRBC BL 28 5V2 RD 29 24V3_FAN RD 30 24V3_STRBC RD 31 24V3_STRC RD 32 24V3_SRRC RD 33 24V3_PM 34 N.C

BR RD BR GY BR GY BR GY BR GY BL BL BL BL

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

FFC-35Pin

SPF PWB

1 SD7 2 GND 3 SD6 4 GND 5 SD5 6 GND 7 SD4 8 GND 9 SD3 10 GND 11 SD2 12 GND 13 SD1 14 GND 15 SD0 16 GND 17 /LST 18 GND 19 SCLK 20 GND 21 LD 22 GND 23 DATA 24 GND 25 CLK 26 GND 27 LGATE 28 GND 29 SCN 30 GND 31 VDS 32 GND 33 VAS 34 GND 35 VLED

1 2 3 4 5 6 7 8 9 10 11 12 BK FG SRA-51T-3

CN2 SD7 B12B-PHDSS-B SD6 SD5 SD4 SD3 SD2 SD1 SD0 /LST SCLK GND GND

BR BR BR BR BR BR BR BR GY BR BR BR BR BR BR BR OR OR RD GY PL GY BL GY BL BR

BR RD BR BR RD BR

RD RD BR BR BR BR

BK

BK

BK BK

WireMesh

SMR-06V-B SMP-06V-BC 6 /SPFMB2 6 5 24V3 5 4 SPFMB2 4 3 3 SPFMA2 2 2 24V3 1 /SPFMA2 1 YL WH RD BR BK OR

BR BR BR BR BR BR BR BR GY BR BR BR BR BR BR BR OR OR RD GY PL GY BL GY BL BR

BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR BR

FG SRA-21T-3 GY GY OR BL RD BR RD BR BL BR BR BR BR BR BR BR BR BR BR BR GY GY

GY

STRRBC WH BK BR OR YL RD

FG SRA-51T-3

BK

CN10 S26B-PHDSS-B 1 2_DATA12 2_DATA1+ 3 2_DATA04 2_DATA0+ 5 2_CLK6 2_CLK+ 7 /2_DBL8 /2_DBL+ 9 GND 10 FRM_CCD2 11 CLK_CCD2 12 PAGE2 13 ADD_CCD2 14 TXD_CCD2 15 RES_CCD2 16 RXD_CCD2 17 3.3V3 18 3.3V3 19 24V3 20 GND 21 12V2 22 GND 23 5V2 24 GND 25 5V2 26 /CISSET

CN11 S20B-PHDSS-B 1 /SLUMA 2 /SLUMB 3 SLUMA 4 SLUMB 5 SPF_SET 6 SRRBC 7 SRRC 8 STRC 9 STRBC 10 SPFC 11 SPFFAN 12 SPPD4 13 SPPD3 14 SPPD2 15 STLD 16 SPWS 17 SPLS2 18 SPLS1 19 SOCD 20 SPOD

SCNcnt PWB

SPSM(42‫)غ‬

SPFM(56‫)غ‬

CN12 S22B-PHDSS-B 1 GND 2 GND 3 VAREF 4 5V1 5 24V3 6 SPPD2 7 24V3 8 SCOV 9 5V2 10 SPPD1 11 /SPFMA 12 SPED1 13 SPFMA 14 STUD 15 /SPFMB 16 SPFMO1 17 SPFMB 18 SPFMO2 19 STRRC 20 STRRBC 21 GND 22 GND

SPPD2

STRRC

B3P-PH-K-S BL 3 5V2 BR 2 SPPD2 GY 1 GND

SMR-06V-N SMP-06V-NC 6 24V3 6 5 24V3 5 4 SPFMB1 4 3 /SPFMB1 3 2 /SPFMA1 2 1 SPFMA1 1

PHNR-3-H +BU3P-TR-P-H PHNR-3-H 3 /STRRBC 1 2 N.C 2 1 24V3 3

PHNR-2-H +BU2P-TR-P-H PHNR-2-H 2 /STRRC 1 1 24V3 2

CN1 2_DATA1- 1 B26B-PHDSS 2_DATA1+ 2 2_DATA0- 3 2_DATA0+ 4 2_CLK5 2_CLK+ 6 /2_DBL7 /2_DBL+ 8 GND 9 FRM_CCD2 10 CLK_CCD2 11 12 PAGE2 ADD_CCD2 13 TXD_CCD2 14 RES_CCD2 15 RXD_CCD2 16 17 3.3V3 18 3.3V3 19 24V3 20 GND 21 12V2 22 GND 23 5V2 24 GND 25 5V2 26 /CISSET

CIScnt PWB

CN3 9604S-35F

GY FG CN2 B32B-PHDSS-B SRA-21T-3 GY GND 1 GY GND 2 OR VAREF 3 N.C 4 RD 24V3 5 BR SPPD2 6 RD 24V3 7 BR SCOV 8 BL 5V2 9 BR SPPD1 10 BR /SPFMA 11 BR SPED1 12 BR SPFMA 13 BR STUD 14 BR /SPFMB 15 BR SPFMO1 16 BR SPFMB 17 BR SPFMO2 18 BR STRRC 19 BR STRRBC 20 BR /SLUMA 21 BR /SLUMB 22 BR SLUMA 23 BR SLUMB 24 BR SPF_SET 25 BR SRRBC 26 BR SRRC 27 BR STRC 28 BR STRBC 29 BR SPFC 30 GY GND 31 GY GND 32

BR BR BR BR RD RD RD RD BR BR BR BR

BR 1 RD 2 RD 3 4 BR 5

BL 1 BR 2 GY 3 4

CN11 B12B-PH-K-S SPFMB1 12 /SPFMB1 11 /SPFMA1 10 SPFMA1 9 24V3 8 24V3 7 24V3 6 24V3 5 SPFMA2 4 /SPFMA2 3 /SPFMB2 2 SPFMB2 1

CN6 /STRRC B5B-PH-K-S 24V3 24V3 N.C /STRRBC

CN4 5V2 B4B-PH-K-S SPPD2 GND N.C

CN2 B8B-PH-K-S GND 1 /RES-SCN 2 /DSR-SCN 3 /RXD-SCN 4 /TXD-SCN 5 /DTR-SCN 6 5V2 7 N.C 8

CN4 B12B-XASK-1(LF) 24V3 1 GND 2 /CV_COPY 3 /CV_COUNT 4 /CV_START 5 /CV_CA 6 /CV_STAPLE 7 /CV_DUPLEX 8 /CV_SIZE0 9 /CV_SIZE1 10 /CV_SIZE2 11 /CV_SIZE3 12

CN5 B13B-PH-K-S /PNC 1 /COPY 2 /CA 3 /READY 4 /ADU 5 5V2 6 GND 7 24V3 8 N.C 9 /TC 10 24V3 11 /PNC-a 12 GND 13

CN13 B2B-PH-K-S CIS_TH 1 GND 2

B. DSPF unit section

MFP CONTROL PWB

+5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5VS +5V1

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

GND2 GND2 1_DATA1+ 2_DATA1+ 1_DATA12_DATA1GND2 GND2 2_DATA0+ 1_CLK+ 2_DATA01_CLKGND2 GND2 2_DBL+ LCDD0+ 2_DBLLCDD0GND2 GND2 LCDD3+ GND2 LCDD3GND2 GND2 CTL-MON LCDM+ LCD1+ LCDMLCD1GND2 /POF-SCN /TXD-SCN /DTR-SCN /SCNSET FRDY SLEEP GND2 GND2 VIDEOinRXD-PCU VIDEOin+ TXD-PCU GND2 /DCCNT DTR-PCU FWP-PCU /POF CFM-PWM +12V1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2

1 2 3 4 5 6 7 8 9 10

/RESET GND2 DD7 DD8 DD6 DD9 DD5 DD10 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 GND2 KEY DMAREQ GND2 /DIOW GND2 /DIOR GND2 IORDY CSEL /DMACK GND2 INTRQ /ICCS10 DA1 /PDIAG//CBLID DA0 DA2 /CS0 /CS1 /DASP GND2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

CN-701 PS-40PE-D4T2-M1

11 12 13 14 15 16 17 18 19 20

CN-702 PS-20PE-D4T2-M1

GND2 GND2 1_DATA0+ 2_CLK+ 1_DATA02_CLKGND2 GND2 1_DBL+ LCDD1+ 1_DBLLCDD1GND2 GND2 LCDD2+ GND2 LCDD2GND2 GND2 GND2 LCDS+ LCD2+ LCDSLCD2GND2 HDD-MON +3.3V +3.3V GND2 /PRON-FAX /RES-MFP /RXD-SCN /DSR-SCN /RES-SCN VCCW-SCN PSSW LCD-VEE LCDDIS WAKEUP +5V-HDD +5V-HDD +5V-HDD +5V-HDD HSYNC DSR-PCU PAGE /MSW-OFF RES-PCU PROFF-CNT (NC)

CN-8 TX24-100R-LT-H1 GND2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

MX-M700N ELECTRICAL SECTION 11 – 10 㨪

/DASP GND2 +12V1 GND2 GND2 +5V-HDD

㨪

39 40 1 2 3 4

+5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5V1 +5VS +5V1

HDD

11 12 13 14 15 16 17 18 19 20

1 2 3 4

+12V1 +5V1 GND2 +5V-HDD GND2

1 2 3 4 5

CN-5 S5P-VH

+12V1 CFM-PWM GND2 HDD-MON

CN-1 S4B-PH-K-S

1 2 3 4

CN-7 B4B-PH-K-S

MOTHER PWB

/PRON-FAX +5VS /POF PROFF-CNT /MSW-OFF FWP-PCU RES-PCU /DCCNT TXD-PCU DTR-PCU GND2 GND2 DSR-PCU PAGE GND2 GND2 RXD-PCU HSYNC GND2 GND2 VIDEOin+ GND2 VIDEOinGND2

+12V1 CFM-PWM GND2 CTL-MON

GND2 1_DATA0+ 2_CLK+ 1_DATA02_CLKGND2 GND2 1_DBL+ LCDD1+ 1_DBLLCDD1GND2 GND2 LCDD2+ GND2 LCDD2GND2 GND2 GND2 LCDS+ LCD2+ LCDSLCD2GND2 HDD-MON +3.3V +3.3V GND2 /PRON-FAX /RES-MFP /RXD-SCN /DSR-SCN /RES-SCN VCCW-SCN PSSW LCD-VEE LCDDIS WAKEUP +5V-HDD +5V-HDD +5V-HDD +5V-HDD HSYNC DSR-PCU PAGE /MSW-OFF RES-PCU PROFF-CNT (NC)

GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2 GND2

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

CN-6 B24B-PHDSS-B

CN-3 PS-20PE-D4T2-M1

GND2 GND2 1_DATA1+ 2_DATA1+ 1_DATA12_DATA1GND2 GND2 2_DATA0+ 1_CLK+ 2_DATA01_CLKGND2 GND2 2_DBL+ LCDD0+ 2_DBLLCDD0GND2 GND2 LCDD3+ GND2 LCDD3GND2 GND2 CTL-MON LCDM+ LCD1+ LCDMLCD1GND2 /POF-SCN /TXD-SCN /DTR-SCN /SCNSET FRDY SLEEP GND2 GND2 VIDEOinRXD-PCU VIDEOin+ TXD-PCU GND2 /DCCNT DTR-PCU FWP-PCU /POF CFM-PWM +12V1

1 /RESET 2 GND2 3 DD7

1 2 3 4 5 6 7 8 9 10

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

CN-8 TX25-100P-8ST-H1

FM-CTL

+12V1 CFM-PWM GND2 HDD-MON

1 2 3 4

1 2 3 4 5 6 7 8 9

+12V1 +5V1 GND2 +5V-HDD GND2 +24V2 GND1 +5V2 GND2

1 2 3 4 5 6 7 8 9

ELP-09V/ELR-09V

4 3 2 1

/LED3 /LED2 /LED1 KEY6 KEY5 KEY4 KEY3 KEY2 KEY1 /OP-SET GND2 +5V2 +5V2 D7 D6 D5 D4 D3 D2 D1 D0 /OP-CS /OP-R/W /OP-RS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CN-4 24FMN-BTK-A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

(PAGE7/8)

FM-HDD

+12V1 +12V1 GND2 GND2

1 2 3 4

CN-3 B4P-VH

1 +24V1 2 +24V1 /CFM-R1 3 /CFM-R2 4 GND2 5 6 GND2 7 +24V1 (NC) 8 /CFM-R3 9 10 TH-RA 11 GND2 12 GND2

CN-21 B12B-PHDSS-B

GND2 +5VLD GND2 GND2 /READY /PMCLK /START +24V1 (NC) +24V1 +5V2 GND2 +5V2 GND2 TEST TEST2 VRB GND2 TEST3 GND2 VIDEO GND2 /VIDEO GND2 LSUS/H GND2 /LDON GND2 /SYNC GND2

CN-22 B30B-PHDSS-B

PCU PWB

PHNR-04-H+BU04P-TR-P-H

1 /PRON-FAX 2 +5VS 3 /POF 4 PROFF-CNT 5 /MSW-OFF 6 FWP-PCU 7 RES-PCU 8 /DCCNT 9 TXD-PCU 10 DTR-PCU 11 GND2 12 GND2 13 DSR-PCU 14 PAGE 15 GND2 16 GND2 17 RXD-PCU 18 HSYNC 19 GND2 20 GND2 21 VIDEOin+ 22 GND2 23 VIDEOin24 GND2

CN-9 B24B-PHDSS-B /LED3 /LED2 /LED1 KEY6 KEY5 KEY4 KEY3 KEY2 KEY1 /OP-SET GND2 +5V2 +5V2 D7 D6 D5 D4 D3 D2 D1 D0 /OP-CS /OP-R/W /OP-RS

1 2 3 4 5 6 7 8 9 10 11 12

TEST3 GND2 /VIDEO VIDEO GND2 GND2 LSUS/H GND2 /LDON GND2 /SYNC GND2 1 2 3 4 5 6 7 8 9 10 11 12

+24V1 /CFM-R1 GND2 +24V1 /CFM-R2 GND2 +24V1 /CFM-R3 GND2 TH-RA GND2

CN-2 B8P-VH 7 GND2 8 +12V1

1 2 3 4 5 6 7 8 9 10 11

DC/PS

1 2 3 4 5 6 7 8 9 10 11

SMP-11V-NC/SMR-11V-N

SMP-12V-NC/SMR-12V-N

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

GND2 +5VLD GND2 GND2 /READY /PMCLK /START +24V1 (NC) +24V1 +5V2 GND2 +5V2 GND2 TEST TEST2 VRB GND2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

1 2 3

1 2 3

1 2 3 4

1 2 3 (NC) (NC) TH-RA GND2

GND2 /SYNC GND2 +5V2

FM-R3

FM-R2

INTPWB

S4B-PH-K-S

3 +24V1 2 /CFM-R3 1 GND2

PHNR-03-H+BU03P-TR-P-H

3 +24V1 2 /CFM-R2 1 GND2

PHNR-03-H+BU03P-TR-P-H

3 +24V1 2 /CFM-R1 1 GND2

1 2 3 4 5 6

1 2 3 4

CN-3 B4B-PH-K-S

/BRAKE /PMCLK /READY /START GND2 +24V1

CN-1 B6B-PH-K-S

FM-R1

LD PWB

PHNR-03-H+BU03P-TR-P-H

GND2 +5VLD GND2 GND2 /READY /PMCLK /START +24V1 /BRAKE +24V1 +5V2 GND2 +5V2 GND2 TEST TEST2 VRB GND2 TEST3 GND2 /VIDEO GND2 VIDEO GND2 LSUS/H GND2 /LDON GND2 /SYNC GND2

CN-2 B30B-PHDSS-B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

(PAGE7/8)

PRT-OP PWB

Un-equipping

SMP-18V-NC/SMR-18V-N

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

CN-1 T24FAZ-SMT-TB

B4B-PH-K-R

/BRAKE /PMCLK /READY /START GND2 +24V1

BD

PGM

B6B-PH-SM3-TB

4 GND2 3 /SYNC 2 GND2 1 +5V2

1 2 3 4 5 6

LSU UNIT

C. Image process section

DRIVER PWB

MX-M700N ELECTRICAL SECTION 11 – 11

CN-2 B12B-PH-K-S /TRM/A 1 /TRMA 2 /TRMB 3 /TRM/B 4 +24V2 5 +24V2 6 /VPM/A 7 /VPMA 8 /VPMB 9 /VPM/B 10 +24V2 11 +24V2 12

CN-4 B26B-PHDSS-B /POM1A 1 /POM1XA 2 /POM1B 3 /POM1XB 4 /POM2A 5 /POM2XA 6 /POM2B 7 /POM2XB 8 /1A 9 /1XA 10 /1B 11 /1XB 12 /2A 13 /2XA 14 /2B 15 /2XB 16 /TRMA 17 /TRMXA 18 /TRMB 19 /TRMXB 20 /VPMA 21 /VPMXA 22 /VPMB 23 /VPMXB 24 (NC) 25 (NC) 26

CN-3 B4P-VH +24V2 4 GND1 3 +5V2 2 GND2 1

CN-1 B12B-PH-K-S /POM1/A 1 /POM1A 2 /POM1B 3 /POM1/B 4 +24V2 5 +24V2 6 /POM2/A 7 /POM2A 8 /POM2B 9 /POM2/B 10 +24V2 11 +24V2 12

VPM

TRM

(PAGE7/8)

SMR-06V-N/SMP-06V-NC 1 /VPM/A 1 2 /VPMA 2 3 3 /VPMB 4 4 /VPM/B 5 5 +24V2 6 6 +24V2

SMR-06V-N/SMP-06V-NC 1 1 /TRM/A 2 /TRMA 2 3 3 /TRMB 4 4 /TRM/B 5 5 +24V2 6 6 +24V2

PCU PWB

CN-10 B26B-PHDSS-B 1 /POM1A 2 /POM1XA 3 /POM1B 4 /POM1XB 5 /POM2A 6 /POM2XA 7 /POM2B 8 /POM2XB 9 /1A 10 /1XA 11 /1B 12 /1XB 13 /2A 14 /2XA 15 /2B 16 /2XB 17 /TRMA 18 /TRMXA 19 /TRMB 20 /TRMXB 21 /VPMA 22 /VPMXA 23 /VPMB 24 /VPMXB 25 (NC) 26 (NC)

AC PWB

CN-5 B16B-PADSS-1 10 +38V +38V 11 +38V 12 14 GND1 GND1 15 GND1 16

CN-6 B18B-PHDSS-B 1 GND2 2 GND2 3 +5V2 4 +5V2 5 /DM 6 /DVM 7 DMCLK DVMCLK 8 9 DM-T 10 DVM-T 11 GND2 12 +5V2 13 /FUM FUMCLK 14 15 FUM-T 16 +24V1 /VFM-BKR 17 18 GND2

1 CN-5 GND2 2 B32B-PHDSS-B +24V1 POD1 3 /VFM-EX1 4 +5V2 5 GND2 6 GND2 7 +24V1 8 POD2 9 /VFM-EX2 10 +5V2 11 GND2 12 GND2 13 +24V1 14 POD3 15 /VFM-EX3 16 +5V2 17 GND2 18 +24V1 19 +24V1 20 /CFM-U1 21 /VFM-BKL 22 GND2 23 GND2 24 +24V 25 +24V1 26 /CFM-U3 27 /CFM-U2 28 GND2 29 GND2 30 TH-EX 31 GND2 32

SMP-02V-NC/SMR-02V-N 1 /PWM-RSV1 1 2 (NC) 2

(PAGE7/8)

(PAGE6/8)

ELP-09V/ELR-09V 1 +12V1 1 2 +5V1 2 3 GND2 3 4 +5V-HDD 4 5 GND2 5 6 +24V2 6 7 GND1 7 8 +5V2 8 9 GND2 9

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /VFM-BKR 2 3 GND2 3

FM-BR

SMP-12V-NC/SMR-12V-N 1 +24V1 1 2 /VFM-EX1 2 3 GND2 3 4 +24V1 4 5 /VFM-EX2 5 6 GND2 6 7 +24V1 7 8 /VFM-EX3 8 9 GND2 9 10 +24V1 10 11 /VFM-BKL 11 12 GND2 12

SMP-18V-NC/SMR-18V-N 1 GND2 1 2 POD1 2 3 +5V2 3 4 GND2 4 5 POD2 5 6 +5V2 6 7 GND2 7 8 POD3 8 9 +5V2 9 10 10 +24V1 11 /CFM-U1 11 12 12 GND2 13 +24V1 13 14 /CFM-U3 14 15 GND2 15 16 TH-EX 16 17 GND2 17 18 /PWM-RSV1 18

POM2

POM1

FM-U4

FM-U3

S5B-PH-K-S 1 2 3 4 5

B2PS-VH S5B-PH-K-S 1 2 3 4 5

B2P-VH B5B-PH-K-S 1 2 3 4 5

GND2 +5V2 /FUM FUMCLK FUM-T

1 +38V 2 GND1

GND2 +5V2 /DVM DVMCLK DVM-T

1 +38V 2 GND1

GND2 +5V2 /DM DMCLK DM-T

B2PS-VH

FUM

DVM

DM

FM-U2

FM-BU

FM-BL

FM-E3

FM-E2

FM-E1

1 +38V 2 GND1

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 /CFM-U2 2 1 GND2 3

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /VFM-BKU 2 3 3 GND2

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 /VFM-BKL 2 1 GND2 3

PHNR-03-H+BU03P-TR-P-H 1 3 +24V1 2 /VFM-EX3 2 1 GND2 3

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 /VFM-EX2 2 3 1 GND2

PHNR-03-H+BU03P-TR-P-H 1 3 +24V1 2 /VFM-EX1 2 3 1 GND2

DELIVERYUNIT

POD3

FM-U1

PHR-3 1 GND2 2 POD3 3 +5V2

INTPWB

S4B-PH-K-S 1 (NC) 2 (NC) 3 TH-EX 4 GND2

PHNR-03-H+BU03P-TR-P-H 1 3 +24V1 2 /PWM-RSV1 2 1 GND2 3

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /CFM-U3 2 3 GND2 3

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /CFM-U1 2 3 GND2 3

SMP-03V-BC/SMR-03V-B 1 GND2 1 2 POD3 2 3 3 +5V2

POD2

POD1

PHR-3(RED) 1 GND2 2 POD2 3 +5V2

PHR-3 1 GND2 2 POD1 3 +5V2

SMR-06V-N/SMP-06V-NC 1 /POM2/A 1 2 /POM2A 2 3 /POM2B 3 4 /POM2/B 4 5 5 +24V2 6 6 +24V2

SMR-06V-N/SMP-06V-NC 1 /POM1/A 1 2 /POM1A 2 3 /POM1B 3 4 /POM1/B 4 5 +24V2 5 6 +24V2 6

D. Paper transport section (1/2)

PHR-3 +5V-M1PFD GND2 M1PFD

1 2 3

PHR-3(RED) 1 GND2 2 M1LUD 3 +5V2

1 2 3

MX-M700N ELECTRICAL SECTION 11 – 12

1 2 3

PHR-2 M1LUM GND2

1 2

Soldering 3 Vref GND2 1 M1PWS 2

PHNR-02-H+BU02P-TR-P-H 2 1 +24V1 2 /DSKPFC1 1

M1PWS

DSKPFC1

PHR-3 +5V-M2PFD GND2 M2PFD

PHR-3(RED) GND2 1 2 M2LUD 3 +5V2

1 2 3

PHNR-02-H+BU02P-TR-P-H 2 1 +24V1 2 /M1PFC 1

M1LUM

M1PFC

M2PFD

M2LUD

PHR-3 GND2 M2PED +5V2

SMP-02V-NC/SMR-02V-N 1 +24V1 1 2 /M2PUS 2

M2PED

M2PUS

PAPER FEED UNIT 2

M1PFD

M1LUD

PHR-3 GND2 M1PED +5V2

SMP-02V-NC/SMR-02V-N 1 +24V1 1 2 /M1PUS 2

M1PED

M1PUS

PAPER FEED UNIT 1

1 2 3 4 5 6 7 8 9 10 11

SMR-03V-N/SMP-03V-NC 1 Vref 1 2 GND2 2 3 3 M1PWS

SMR-11V-N/SMP-11V-NC 1 +24V1 2 /M2PUS 3 GND2 4 M2PED 5 +5V2 6 GND2 7 M2LUD 8 +5V2 9 +5V-M2PFD 10 GND2 11 M2PFD

SMR-11V-N/SMP-11V-NC 1 1 +24V1 2 2 /M1PUS 3 3 GND2 4 4 M1PED 5 5 +5V2 6 6 GND2 7 7 M1LUD 8 8 +5V2 9 9 +5V-M1PFD 10 GND2 10 11 M1PFD 11

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 M1PWS

+24V1 +24V1 /M1PUS /M2PUS GND2 GND2 M1PED M2PED +5V2 +5V2 GND2 GND2 M1LUD M2LUD +5V2 +5V2 +5V-M1PFD +5V-M2PFD GND2 GND2 M1PFD M2PFD +24V1 +24V1 /M1PFC /DSKPFC1 M1LUM Vref GND2 GND2 (NC)

CN-16 B32B-PHDSS-B

PCU PWB

T1LUM T2LUM GND2 GND2 +24V1 +24V1 /T1PUS /T2PUS +5V2 +24V1 GND2 /DSKLS T1LUD GND2 T1PED T1SPD +5V2 +5V2 GND2 GND2 T2LUD T2SPD T2PED +5V2

CN-14 B24B-PHDSS-B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

SMP-10V-NC/SMR-10V-N 1 1 +5V2 2 2 GND2 3 3 T2LUD 4 4 T2PED 5 5 GND2 6 6 T1SPD 7 7 +5V2 8 8 GND2 9 T2SPD 9 10 +5V2 10

SMR-04V-N/SMP-04V-NC 1 +5V2 1 2 GND2 2 3 T1LUD 3 4 T1PED 4

PHR-2 T1LUM GND2

PHR-2 T2LUM GND2

1 2 3

1 2 3

1 2 3 4

1 2 3 4

PHR-3 GND2 T2SPD +5V2

PHR-3 GND2 T1SPD +5V2

S4B-PH-K-S +5V2 GND2 T2LUD T2PED

S4B-PH-K-S +5V2 GND2 T1LUD T1PED

T2SPD

T1SPD

T2S PWB

T1S PWB

T2PUS

T2LUM SMR-02V-N/SMP-02V-NC 1 1 +24V1 2 /T2PUS 2

1 2

T1PUS

T1LUM

SMR-02V-N/SMP-02V-NC 1 +24V1 1 2 /T1PUS 2

1 2

E. Paper transport section (2/2)

MX-M700N ELECTRICAL SECTION 11 – 13

(PAGE7/8)

ELP-12V/ELR-12V 1 TXD-FIN 1 2 RXD-FIN 2 3 /DTR-FIN 3 4 /DSR-FIN 4 5 RES-FIN 5 6 6 +24V5 7 7 +5V2 8 8 GND2 9 9 GND1 10 F-GND 10 11 +24V6 11 12 GND1 12

ELP-12V/ELR-12V 1 TXD-FIN 1 2 RXD-FIN 2 3 /DTR-FIN 3 4 /DSR-FIN 4 5 RES-FIN 5 6 6 +24V5 7 7 +5V2 8 GND2 8 9 GND1 9 10 10 F-GND 11 11 +24V6 12 12 GND1

PHR-3 GND2 1 2 3

PHR-3 +5V-T1PPD 1 GND2 2 T1PPD 3

PHR-3 1 GND2 TANSET 2 +5V2 3

S5B-PH-K-S 1 GND2 2 +5V2 3 /MM 4 MMCLK MM-T 5

DSWDSK DSW-DSK +5V2

T1PPD

TANSET

MM

B2PS-VH +38V 1 2 GND1

CN-5 B16B-PADSS-1 GND1 13 +38V 9

AC PWB

DC/PS

CN-4 B7P-VH +24V5 1 2 GND1 +24V6 3 GND1 4

1 M2LUM 1 2 GND2 2 3 +24V1 3 4 /M2PFC 4 5 GND2 5 6 TXD-FIN 6 7 RXD-FIN 7 8 /DTR-FIN 8 9 /DSR-FIN 9 10 RES-FIN 10 SMR-10V-N/SMP-10V-NC

SMP-06V-NC/SMR-06V-N 1 +5V-T1PPD 1 2 2 GND2 3 T1PPD 3 4 4 GND2 5 DSW-DSK 5 6 +5V2 6

SRA-21T-4

PHNR-03-H+BU03P-TR-P-H 3 +5V-T1PPD 1 2 GND2 2 3 1 T1PPD

PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /M2PFC 1

1 2

SMP-02V-NC/SMR-02V-N 1 1 +5V2 2 (NC) 2

(PAGE7/8)

TXD-FIN RXD-FIN /DTR-FIN /DSR-FIN RES-FIN +24V5 +5V2 GND2 GND1 F-GND +24V6 GND1

(PAGE7/8)

IST

FIN

ELP-12V TXD-FIN 1 RXD-FIN 2 /DTR-FIN 3 /DSR-FIN 4 RES-FIN 5 6 +24V5 7 +5V2 8 GND2 GND1 9 F-GND 10 11 +24V6 12 GND1

OPTION

FIN

M2PFC OPTION

PHR-2 M2LUM GND2

PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /DSKPFC2 1

PHNR-03-H+BU03P-TR-P-H 1 +24V1 3 2 (NC) 2 3 /T1PFC 1

M2LUM

DSKPFC2

T1PFC

CN-25 B6B-PH-K-S 1 +5V-T1PPD 2 (NC) 3 T1PPD 4 (NC) 5 GND2 6 (NC)

CN-17 B30B-PHDSS-B 1 M2LUM 2 +24V1 3 GND2 4 /T1PFC 5 +24V1 6 +24V1 7 /M2PFC 8 /DSKPFC2 9 GND2 10 GND2 11 TXD-FIN 12 +5V2 13 RXD-FIN 14 /MM 15 /DTR-FIN 16 MMCLK 17 /DSR-FIN 18 MM-T 19 RES-FIN 20 TSW-LED 21 (NC) 22 TSW 23 GND2 24 GND2 25 TANSET 26 GND2 27 +5V2 28 DSW-DSK 29 (NC) 30 +5V2

CN-13 B26B-PHDSS-B DSW-F(R) 1 (NC) 2 (NC) 3 GND2 4 +24V1 5 6 MPLD1 7 /MFPUS 8 +5V2 9 GND2 10 MPLD2 11 MPED 12 MTOP1 13 +5V2 14 MTOP2 15 +24V1 16 MPFPWS 17 /MPFGS 18 Vref +5V-MPFD1 19 20 /MPFC 21 MPFD1 +24V1 22 23 GND2 24 GND2 (NC) 25 DSW-R 26

PCU PWB

CN-18 B14B-PHDSS-B GND2 1 +5V-MPFD2 2 TXD-LCC 3 GND2 4 RXD-LCC 5 MPFD2 6 7 /DTR-LCC +5V-LPPD 8 /DSR-LCC 9 10 GND2 11 RES-LCC 12 LPPD /TRC-LCC 13 (NC) 14

DRAWER QR/P4-24S-C(01)/ QR/P4-24P-C(01) 1 DSW-F(R) 1 2 2 GND2 3 3 MPLD1 4 4 +5V2 5 5 MPLD2 6 6 MTOP1 7 7 MTOP2 8 8 GND2 9 MPFPWS 9 10 10 Vref 11 11 /MPFC 12 12 +24V1 13 13 +24V1 14 14 /MFPUS 15 GND2 15 16 MPED 16 17 +5V2 17 18 +24V1 18 19 /MPFGS 19 20 +5V-MPFD1 20 21 21 GND2 22 MPFD1 22 ( ) 23 NC 23 24 DSW-R 24

SMR-06V-N/SMP-06V-NC 1 +5V-MPFD2 1 2 GND2 2 3 MPFD2 3 4 +5V-LPPD 4 5 GND2 5 6 LPPD 6

(PAGE7/8)

(PAGE7/8)

DC/PS

WH PWB

LPPD

LCC

OPTION

PHNR-09-H+BU09P-TR-P-H 9 1 GND2 8 2 MPLD1 7 3 +5V2 6 4 MPLD2 5 5 MTOP1 4 6 MTOP2 3 7 GND2 8 MPFPWS 2 1 9 Vref

DSW-R

PS-187

MPFPWS

MTOP2

MTOP1

MPLD2

MPLD1

MPED

MFPUS

PHR-3 1 +5V-MPFD1 2 GND2 3 MPFD1

MPFD1

MPFGS

SMR-02V-N/SMP-02V-NC 1 +24V1 1 2 /MPFGS 2

DF3-3S-2C 1 GND2 2 MPED 3 +5V2

SMR-02V-N/SMP-02V-NC 1 +24V1 1 2 /MFPUS 2

MPFC

PHNR-03-H+BU03P-TR-P-H 1 3 +24V1 2 2 (NC) 1 /MPFC 3

PHR-3 1 GND2 2 MPFPWS 3 Vref

179228-2 1 MTOP2 2 GND2

179228-2 1 MTOP1 2 GND2

DF3-3S-2C 1 GND2 2 MPLD2 3 +5V2

DF3-3S-2C 1 GND2 2 MPLD1 3 +5V2

MANUAL PAPER FEED UNIT

PHR-3 1 +5V-LPPD 2 GND2 3 LPPD

MPFD2

ELR-15V/ELP-15V 1 1 (NC) 2 (NC) 2 3 TXD-LCC 3 4 RXD-LCC 4 5 /DTR-LCC 5 6 /DSR-LCC 6 7 RES-LCC 7 8 8 F-GND 9 +5V2 9 10 GND2 10 11 +24V4 11 12 12 GND1 13 /TRC-LCC 13 14 14 (+3.3V) 15 (GND1) 15

ELR-12V/ELP-12V 4 WH-L 4 12 WH-N 12 5 F-GND 5

PHR-3 1 +5V-MPFD2 2 GND2 3 MPFD2

SRA-21T-4

SRA-21T-4

SMP-06V-NC/SMR-06V-N 1 +5V-MPFD2 1 2 2 GND2 3 3 MPFD2 4 +5V-LPPD 4 5 5 GND2 6 LPPD 6

CN-6 B10P-VH +5V2 7 CN-3 B9P-VH +24V4 7 GND1 8

CN-5 B2P3-VH-BK WH-L 3 WH-N 1

F. Transport/Option section

CN-7 B32B-PHDSS-B 1 +24V1 +24V1 2 /CFM-DV 3 /RRC 4 5 GND2 (NC) 6 7 +24V1 +24V(DSW) 8 +5V-APPD1 9 PFD2 10 +5V-APPD2 11 /CFM-ADU 12 +5V-PFD2 13 THPS2 14 +5V-DSW 15 TURM 16 +5V-AINPD 17 /TCB-PWM 18 (NC) 19 (NC) 20 +5V-THPS2 21 /TCBIAS 22 (NC) 23 APPD1 24 DSW-ADU 25 APPD2 26 /DGS 27 AINPD 28 29 GND2 30 GND2 31 (NC) 32 DSW-L

PCU PWB

CN-5 B9B-PH-K-S /1/A 1 /1A 2 3 /1B 4 /1/B 5 /2/A 6 /2A 7 /2B 8 /2/B +24V2 9

DRIVER PWB

DRAWER 1 DSW-L 1 2 /ADUM2/A 2 3 /ADUM2A 3 4 /ADUM2B 4 5 /ADUM2/B 5 6 +5V-APPD1 6 7 +5V-APPD2 7 8 +5V-PFD2 8 9 +5V-DSW 9 10 +5V-AINPD 10 11 (NC) 11 12 /ADUM1/A 12 13 /ADUM1A 13 14 /ADUM1B 14 15 /ADUM1/B 15 16 +24V1 16 17 +24V(DSW) 17 18 PFD2 18 19 /CFM-ADU 19 20 THPS2 20 21 21 TURM 22 /TCB-PWM 22 23 23 /TCBIAS 24 +5V-THPS2 24 25 25 GND2 26 26 GND2 27 27 APPD1 28 28 APPD2 29 29 AINPD 30 DSW-ADU 30 31 31 /DGS 32 32 +24V2 QR/P4-32S-C(01)/QR/P4-32P-C(01) SRA-21T-4

MX-M700N ELECTRICAL SECTION 11 – 14

SRA-21T-4

SRA-21T-4

PHNR-03-H+BU03P-TR-P-H 3 AINPD 1 2 2 GND2 1 +5V-AINPD 3

SRA-21T-4

SRA-21T-4

SMR-12V-N/SMP-12V-NC 1 +5V-PFD2 1 2 2 PFD2 3 +5V-THPS2 3 4 4 THPS2 5 /TCB-PWM 5 6 6 /TCBIAS 7 7 DSW-L 8 8 DSW-L 9 9 GND2 10 TURM 10 11 11 +24V1 12 /CFM-ADU 12

DSW-L

PS-187

RRC

FM-DV

DSW DGS

ADUM1

AINPD

PHNR-02-H+BU02P-TR-P-H 2 +24V1 1 1 DGS 2

179228-3 1 DSW-ADU 2 GND2 3 +5V-DSW

179228-3 1 AINPD 2 GND2 3 +5V-AINPD

SMR-06V-N/SMP-06V-NC 1 /ADUM1/A 1 2 /ADUM1A 2 3 /ADUM1B 3 4 /ADUM1/B 4 5 5 +24V2 6 6 +24V2

SRA-21T-4

ADUM2

TB PWB

FPS-187 Bias

SMR-06V-N/SMP-06V-NC 1 /ADUM2/A 1 2 /ADUM2A 2 3 /ADUM2B 3 4 /ADUM2/B 4 5 5 +24V2 6 6 +24V2

B6B-PH-K-S 1 DSW-L 2 DSW-L 3 /TCBIAS 4 /TCB-PWM 5 GND2 6 F-GND

FM-ADU

TBRM Un-equipping

THPS2

PFD2

APPD2

APPD1

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 /CFM-ADU 2 1 GND2 3

PHR-2 1 TURM 2 GND2

179228-3 1 THPS2 2 GND2 3 +5V-THPS2

PHR-3 1 +5V-PFD2 2 GND2 3 PFD2

PHR-3 1 +5V-APPD2 2 GND 3 APPD2

PHR-3 1 +5V-APPD1 2 GND2 3 APPD1

LEFT DOOR UNIT

PHNR-02-H+BU02P-TR-P-H 2 +24V1 1 1 /RRC 2

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /CFM-DV 2 3 GND2 3

G. Left door transport section

DRAWERTSR-04V-K 1 GND2 +5V2 2 CRUCLK 3 CRUSDA 4

SMR-02V-N/SMP-02V-NC 1 TM1a 1 2 2 TM1b

MX-M700N ELECTRICAL SECTION 11 – 15

M2SPD

M2SS PWB

M1SPD

M1SS PWB

1 2 3 4 5 6

PHR-3 GND2 1 M2SPD 2 +5V2 3

S6B-PH-K-S (NC) GND2 M2SS1 M2SS2 M2SS3 M2SS4

PHR-3 GND2 1 M1SPD 2 +5V2 3

1 2 3 4 5 6

FPS-187(WH) THV

SRA-21T-3

S6B-PH-K-S (NC) GND2 M1SS1 M1SS2 M1SS3 M1SS4

PS-187(YL) GB

SAA-21T-4L

PS-187(GR) Bias

PS-187(RD) MHV

SMR-02V-N/SMP-02V-NC 1 TM2a 1 2 TM2b 2

SAA-21T-4L

TM2

CRUM

TM1

TFSD

PHR-4 +24V1 1 TFSD 2 (NC) 3 GND2 4

TONER HOPPER

HV

CN-1 B16B-PH-K-S DSW-F 1 GND2 2 GND2 3 /GBPWM 4 /MHVREM 5 MHV-T 6 /THV+PWM 7 THV+REM 8 /CHV-PWM 9 /CHV-REM 10 /CHVAWM 11 /CHVACREM 12 /DVPWM 13 /DVREM 14 HVREM 15 16 +24V1

SMP-18V-NC/SMR-18V-N 1 1 GND2 2 2 M1SS1 3 M1SS2 3 4 4 M1SS3 5 M1SS4 5 6 GND2 6 7 M1SPD 7 8 +5V2 8 9 (NC) 9 10 10 GND2 11 11 M2SS1 12 12 M2SS2 13 M2SS3 13 14 M2SS4 14 15 GND2 15 16 M2SPD 16 17 +5V2 17 (NC) 18 18

SRA-01T-3.2

TSDP-12V-K/TSDR-12V-K 1 1 +24V1 2 2 TFSD 3 3 GND2 4 4 (NC) 5 5 TM1a 6 6 TM1b 7 (NC) 7 8 GND2 8 9 +5V2 9 10 CRUCLK 10 11 CRUSDA 11 12 GND2 12

SRA-01T-3.2

CN-15 B34B-PHDSS-B 1 DSW-F 2 (NC) 3 GND2 4 GND2 5 /GBPWM 6 /MHVREM 7 MHV-T 8 /THV+PWM 9 THV+REM 10 /CHV-PWM 11 /CHV-REM 12 /CHVAWM 13 /CHVACREM 14 /DVPWM 15 /DVREM 16 HVREM 17 +24V1 18 (NC) 19 GND2 20 GND2 21 M1SS1 22 M2SS1 23 M1SS2 24 M2SS2 25 M1SS3 26 M2SS3 27 M1SS4 28 M2SS4 29 GND2 30 GND2 31 M1SPD 32 M2SPD 33 +5V2 34 +5V2

CN-11 B12B-PHDSS-B 1 TM1a 2 GND2 3 TM1b 4 +5V2 5 TM2a 6 CRUCLK 7 TM2b 8 CRUSDA 9 +24V1 10 GND2 11 TFSD 12 TNCA

PCU PWB

CN-12 B30B-PHDSS-B 1 +24V1 2 +24V1 3 /T2PFC 4 /HPLS 5 +24V1 6 DVCH1 7 /HPFC DVCH2 8 9 +24V1 DVCH3 10 11 /PSBC DVCH4 12 +5V2 13 +24V1 14 PPD 15 TCS 16 GND2 17 GND2 18 +5V-MPRD1 19 TSGOUT 20 GND2 21 GND2 22 MPRD1 23 +5V2 24 +5V-MPRD2 25 26 HUS-DV GND2 27 28 GND2 MPRD2 29 30 TH-DV

CN-8 B20B-PHDSS-B PCS-LED 1 DMS-LED 2 PCS 3 DMS 4 5 +12V2 6 +12V2 7 +24V-DL +24V1 8 /DL 9 /PTDL 10 11 +24V1 12 TH-CL /PSPS 13 GND2 14 15 +5V2 TLS 16 HUS-TC 17 GND2 18 GND2 19 /PWM-RSV1 20 SRA-01T-3.2

1 1 +24V1 2 2 /PSBC 3 3 +5V2 4 4 PPD 5 5 GND2 6 +5V-MPRD1 6 7 7 GND2 8 8 MPRD1 9 +5V-MPRD2 9 10 10 GND2 11 11 MPRD2 12 12 +24V1 13 13 /HPLS 14 14 (NC) 15 15 (NC) 16 16 (NC) 17 17 (NC) 18 18 (NC) SMR-18V-N/SMP-18V-NC

SMP-02V-NC/SMR-02V-N 1 /PWM-RSV1 1 2 (NC) 2

DRAWER TSDR-20V-K/TSDP-20V-K 1 PCS-LED 1 2 PCS 2 3 +12V2 3 4 DMS-LED 4 5 DMS 5 6 +12V2 6 7 +24V-DL 7 8 8 /DL 9 9 +24V1 10 /PTDL 10 11 (NC) 11 12 +24V1 12 13 /PSPS 13 14 TH-CL 14 15 GND2 15 16 (NC) 16 17 (NC) 17 18 (NC) 18 19 (NC) 19 20 GND2 20

TLS

INTPWB

PSPS

DMS

1 2 3 1 2

PSBC

PS UNIT

HPFC

T2PFC

1 2 3 4

1 2 3 4

TCS

HUS-DV

SRA-01T-3.2

ZHR-4 +5V2 HUS-DV GND2 TH-DV

51021-0400 TSGOUT +24V1 TCS GND2

DEVELOPER UNIT

HPLS

MPRD2

MPRD1

PPD

SMP-02V-NC/SMR-02V-N 1 +24V1 1 2 /HPLS 2

PHR-3 1 +5V-MPRD2 2 GND2 3 MPRD2

PHR-3(RED) 1 +5V-MPRD1 2 GND2 3 MPRD1

179228-3 1 +5V2 2 PPD 3 GND2

PHNR-02-H+BU02P-TR-P-H 1 2 +24V1 2 1 /PSBC

2 +24V1 1 /HPFC

PHNR-02-H+BU02P-TR-P-H

3 +24V1 2 (NC) 1 /T2PFC

PHNR-03-H+BU03P-TR-P-H

1 TLS 2 GND2

179228-2

S4B-PH-K-S 1 (NC) 2 (NC) 3 TH-CL 4 GND2

DRAWER 1 1 DVCH1 2 2 DVCH2 3 3 DVCH3 4 4 DVCH4 5 5 +24V1 6 6 TCS 7 GND2 7 8 TSGOUT 8 9 (NC) 9 10 10 GND2 11 11 (NC) 12 12 +5V2 13 13 HUS-DV 14 14 GND2 15 15 TH-DV (NC) 16 16 (NC) 17 17 18 18 (NC) 19 (NC) 19 20 20 DV-Bias QR/P8-20S-C(01)/QR/P8-20P-C(01)

SMR-08V-N/SMP-08V-NC 1 +5V-MPRD1 1 2 GND2 2 3 MPRD1 3 4 +5V-MPRD2 4 5 GND2 5 6 MPRD2 6 7 7 +24V1 8 /HPLS 8

PHNR-06-H+BU06P-TR-P-H 6 1 +24V1 2 /PSBC 5 3 +5V2 4 3 4 PPD 2 5 GND2 6 (NC) 1

(PAGE2/8)

PHNR-05-H+BU05P-TR-P-H 1 +5V2 5 2 HUS-TC 4 3 GND2 3 4 TLS 2 5 GND2 1

SRA-01T-3.2

DL

SMP-02V-BC/SMR-02V-B 1 1 +24V1 2 2 /PSPS

PHR-3 1 +24V-DL 2 (NC) 3 /DL

SMR-03V-B/SMP-03V-BC 1 1 +12V2 2 2 DMS 3 3 DMS-LED

PCS

PROCESS UNIT SMR-03V-B/SMP-03V-BC 1 1 +12V2 2 2 PCS 3 3 PCS-LED

H. Process section

DSW-L(F) (NC) DSW-F (NC) +24V1 /MSWPR +24V1 /PNC

1 2 3 4 5 6 7 8

SMR-08V-N/SMP-08V-NC

1 DSW-F 2 3 4 5 6 7 8

FPS-187

MX-M700N ELECTRICAL SECTION 11 – 16

#250(WH) Nin

#250(BK) Nout

#250(WH) Lin

#250(BK) Lout

#250(YL) MSWN

FM-DC2

FM-DC1

CN-4 B2P3-VH 1 WH-N(DSK2) 2 (NC) 3 WH-L(DSK2) CN-5 B2P3-VH-BK 1 WH-N(LCC) 2 (NC) 3 WH-L(LCC)

CN-2 B2P3-VH-BL 1 WH-N(SCN) 2 (NC) 3 WH-L(SCN) CN-3 B2P3-VH 1 WH-N(DSK1) 2 (NC) 3 WH-L(DSK1)

PHNR-03-H+BU03P-TR-P-H 3 1 +24V1 2 /CFM-DC2 2 1 3 GND2

PHNR-03-H+BU03P-TR-P-H 1 +24V1 3 2 /CFM-DC1 2 3 GND2 1

12 WH-N(LCC) 12 5 F-GND 5 4 WH-L(LCC) 4

ELP-12V/ELR-12V

2 WH-N(DSK2) 2 1 WH-L(DSK2) 1

ELP-02V/ELR-02V

2 WH-N(DSK1) 2 1 WH-L(DSK1) 1

ELP-02V/ELR-02V

SRA-21T-4

WH-DSK2

WH-DSK1

WH-SCN

2 WH-N(SCN) 2 1 WH-L(SCN) 1

ELP-02V/ELR-02V

HL-2L HL-1N HL-2N HL-3N HL-3L HL-1L

1 2 3 4 5 6

ELR-02V/ELP-02V 1 MSWL 1 2 MSWN 2

ELP-02V/ELR-02V 1 MSWL 1 2 MSWN 2

CN-6 B3B-PH-K-S /WHPR2 1 2 (NC) +24V1 3

(PAGE7/8)

SMP-06V-NC/SMR-06V-N 1 1 +24V1 2 /CFM-DC1 2 3 3 GND2 4 +24V1 4 5 /CFM-DC2 5 6 6 GND2

WH PWB

CN-1 B2P3-VH- R 1 WH-N 2 (NC) 3 WH-L

FAX

WH -SW

PS-250

SRA-51T -4

VLP-06V/VLR-06V 1 LFout 1 2 2 F-GND 3 3 (NC) 4 4 NFout 5 (NC) 5 6 (NC) 6

VLR-03V/VLP-03V 1 Nout 1 2 N1in 2 3 N2in 3

VLP-03V/VLR-03V 3 Nout 3 2 N1in 2 1 1 N2in

VLP-03V-R/VLR-03V-RVLR-03V-R/VLP-03V-R 1 1 Lout 1 Lout 1 2 L1in 2 L1in 2 2 3 3 L2in 3 L2in 3

1 2 3 4 5 6

OPTION

VLP-01V/VLR-01VF 1 HL-1L 1

VLP-01V/VLR-01VF 1 HL-2L 1

SLR-01VF/SLP-01V 1 HL-3N 1

Standard:JPN OPTION:EX100/EX200

MRSW

#250(WH) Nout

#110(WH) +24V1

#250(BL) N2in

#250(YL) MSWL

#250(BL) L2in

#250(WH) Lout

SPS-51T-187

#110(WH) /MSWPR

MSW

SPS-51T-187

SPS-51T-187

SPS-51T-187

HL3

SPS-51T-187

SPS-51T-187

RTH3

RTH2

RTH1

WEBM

WEBEND

DRAWER 19LP-RWZV-K4GG-P6/19LR-RWZV-K2GG-R6 PHNR-05-H+BU05P-TR-P-H RCZR-10V-PS 179228-3 5 +5V-WEBENDD 1 +5V-WEBENDD 1 10 +5V-WEBENDD 1 WEBENDD 2 4 WEBENDD 2 2 9 WEBENDD GND2 3 3 GND2 3 3 8 GND2 SMR-02V-N/SMP-02V-NC 4 4 2 WEBMA 7 WEBMA 1 WEBMB 5 5 1 WEBMA 1 6 WEBMB 2 WEBMB 6 2 5 (NC) 7 4 (NC) 8 3 (NC) PHNR-04-H+BU04P-TR-P-H 2 (NC) 9 4 RTH1 1 10 1 (NC) 3 GND2 2 RCZR-09V-PS 2 RTH2 3 9 1 GND2 4 1 RTH1 8 2 GND2 7 3 RTH2 PHNR-02-H+BU02P-TR-P-H 6 4 GND2 1 2 RTH3 5 RTH3 5 1 GND2 2 4 6 GND2 3 7 (NC) SRA-51T-3 SRA-51T-3 2 8 (NC) 1 9 (NC) SRA-51T-3 SRA-51T-3

HL1 HL2

179228-2 +24V1 1 /PNC 2

FUSINGUNIT

PNC

OPTION

1 2 3 4 5 6

#250(WH) N

#250(BK) L

#187(WH) WH-N #187(BK) WH-L

AC PWB

CN-1 B2P3-VH-BL 1 MSWL 2 (NC) 3 MSWN

#250(WH) N2in

#250(YL) N1in NFou

#250(BK) L2i n

#250(BL) L1in LFout

#250(GR) Nout

#250(RD) Lout

#250(YL) Nout N1in

#250(RD) Nin

#250(BL) Lout L1in

#250(GR) Lin

CN-4 B9B-PH-K-S +12VS 1 BUP-PR 2 GND2 3 +38V-MON 4 5 INTPR2 GND2 6 INTPR 7 8 GND2 9 +24VPR

CN-5 B16B-PADSS-1 1 +38V1 2 +38V2 3 +38V3 4 (NC) 5 GND1 GND1 6 GND1 7 8 (NC) 9 +38V 10 +38V +38V 11 +38V 12 13 GND1 GND1 14 GND1 15 GND1 16

CN-2 B2P3-VH-BK 1 MSWN1 (NC) 2 3 MSWL1

1 2 3

#250(YL) N(HL)

#250(BK) L(HL)

#250(WH) N(HL)

#250(BK) L(HL)

CN-3 B6B-PH-K-S +24VPR 1 2 HLPR12 3 GND2 HLCNT2 4 HLCNT1 5 GND2 6

CN-4 B06B-PASK 1 +12VS 2 GND2 AC-MON 3 FW-SUB 4 HLCNT3 5 GND2 6

CN-3 B2P3-VH L(DC) (NC) N(DC)

SUB P/S PWB

PCUPWB

CN-2 B03P-VL-R 1 HL1-L 2 HL2-N 3 HL3-N

CN-1 B03P-VL 1 HL-1L 2 HL3-L 3 HL2-L

CN-24 B6B-PH-K-S +5V-WEBENDD WEBENDD GND2 WEBMA WEBMB Reserve7

FUM

DVM

B2PS-VH 1 +38V 2 GND1 B2PS-VH 1 +38V 2 GND1

DM

MM

CN-4 B7P-VH 1 +24V5 GND1 2 +24V6 3 GND1 4 +24V7 5 6 GND1 (NC) 7

CN-2 B8P-VH 1 /DCCNT /MSW-MON 2 3 GND2 4 +5V1 5 GND2 6 +12V1 7 GND2 8 +12V1

CN-7 B2P-VH 1 +3. 3V 2 GND2

CN-6 B10P-VH +5V2 1 GND2 2 +5V2 3 GND2 4 +5V2 5 GND2 6 +5V2 7 GND2 8 +5V2 9 GND2 10

(PAGE2/8)

(PAGE2/8)

(PAGE2/8)

(PAGE4/8)

D/S

B2PS-VH 1 +38V 2 GND1

B2PS-VH 1 +38V 2 GND1

CN-8 B6P-VH 1 +38V1 2 GND1 3 +38V2 4 GND1 5 +38V3 6 GND1

CN-ACin B2P3-VH L(DC) 1 2 (NC) N(DC) 3 CN-1 B03B-XASK-1 1 MSWN1 2 (NC) 3 MSWL1

VLR-02V/VLP-02V-1 1 1 L(HL) 2 2 N(HL)

VLR-02V/VLP-02V 1 L(HL) 1 2 N(HL) 2

CN-5 B4P-VH +12V2 1 GND2 2 +12V2 3 GND2 4

CN-3 B9P-VH +24V1 1 2 GND1 3 +24V2 4 GND1 5 +24V3 GND1 6 7 +24V4 GND1 8 FW 9

SMP-02V-NC/SMR-02V-N 1 +5V2 1 2 GND2 2

ELR-12V/ELP-12V 6 6 +24V5 9 GND1 9 11 11 +24V6 12 GND1 12

ELR-15V/ELP-15V 9 +5V2 9 11 +24V4 11 12 GND1 12

CN-8 B6PS-VH +24V3 GND1 +12V2 GND2 +5V2 GND2

SCN PWB

(PAGE4/8)

(PAGE4/8)

(PAGE4/8)

1 2 3 4 5 6

(PAGE1/8)

(PAGE1/8) (PAGE2/8)

(PAGE7/8)

SMP-06V-NC/SMR-06V-N 1 +24V1 1 2 /CFM-DC1 2 3 GND2 3 4 +24V1 4 5 /CFM-DC2 5 6 GND2 6

ELR-09V/ELP-09V 1 +12V1 1 2 +5V1 2 3 3 GND2 4 +5V-HDD 4 5 GND2 5 6 +24V2 6 7 GND1 7 8 +5V2 8 9 GND2 9

CN-19 B24B-PHDSS-B 1 +24V1 2 +24V1 3 /CFM-DC1 4 /CFM-DC2 5 GND2 6 GND2 7 +12VS 8 /WHPR1 9 BUP-PR 10 +24V1 11 GND2 12 GND2 13 +24V-INT 14 +38V-MON 15 INTPR 16 GND2 17 GND2 18 /WHPR2 19 INTPR2 20 +24V1 21 GND2 22 (NC) 23 /MSW-MON 24 /DCCNT

PCU PWB

CN-2 B28B-PHDSS-B 1 GND2 2 +24VPR 3 GND2 4 GND2 5 HLPR12 6 RTH1 7 HLPR3 8 GND2 9 HLCNT1 10 RTH2 11 HLCNT2 12 GND2 13 +24V1 14 RTH3 15 /MSWPR 16 GND2 17 +24V1 18 +24V1 19 DSW-FD 20 /PNC 21 GND2 22 GND2 23 DSW-L(F) 24 GND2 25 GND2 26 GND2 27 GND2 28 DSW-F CN-20 B9P-VH 1 +24V1 2 +12V2 3 +5V2 4 +3.3V 5 GND1 6 GND2 7 GND2 8 GND2 9 FW

CN-1 B06B-PASK 1 +12VS 2 GND2 3 AC-MON 4 FW-SUB 5 HLCNT3 6 GND2

I. Power source peripheral section

MX-M700N ELECTRICAL SECTION 11 – 17

FUM

DVM

VFM-BKR

CN-6

TH-EX

CFM-U2

VFM-BKL

VFM-EX3

VFM-EX2

VFM-EX1

CN-5

CN-4 1 /LED3 2 /LED2 3 /LED1 4 KEY6 5 KEY5 6 KEY4 7 KEY3 8 KEY2 9 KEY1 10 /OP-SET 11 GND2 12 +5V2 13 +5V2 14 D7 15 D6 16 D5 17 D4 18 D3 19 D2 20 D1 21 D0 22 /OP-CS 23 /OP-R/W 24 /OP-RS

CN-3 1 +12V1 2 +12V1 3 GND2 4 GND2

DSW-F

PNC

RTH

SUB P/S

CN-2

CN-1 1 +12VS 2 GND2 3 AC-MON 4 FW-SUB 5 HLCNT3 6 GND2

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27

GND2 +5V2 /DVM DVMCLK DVM-T +5V2 FUMCLK +24V1 GND2

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17

2 1 4 3 6 5 8 7 /VFM-EX2 10 9 GND2 12 11 14 13 +24V1 /V FM-E X3 16 15 18 17 GND2 +24V1 20 19 /VFM-BKL 22 21 24 23 GND2 +24V1 26 25 /CFM-U2 28 27 30 29 GND2 3 2 31 GND2

+24V1 /VFM-EX1 GND2 +24V1

PRT-OP

24FMN-BTK-A

HDD

B4P-VH

DSW-F

+24V1 /PNC GND2 GND2 GND2

+24VPR GND2 RTH1 GND2 RTH2 GND2 RTH3 GND2

SUB P/S

B06B-PASK

GND2 +5V2 /DM DMCLK DM-T GND2 /FUM FUM-T /VFM-BKR

GND2 POD1 +5V2 GND2 POD2 +5V2 GND2 POD3 +5V2 +24V1 /CFM-U1 GND2 +24V1 /CFM-U3 GND2 TH-EX

GND2 GND2 HLPR12 HLPR3 HLCNT1 HLCNT2 +24V1 /MSWPR +24V1 DSW-FD GND2 DSW-L(F) GND2 GND2

/VFM-BKR

FUM

DM

B18B-PHDSS-B

TH-EX

CFM-U 3

/CFM-U1

POD3

POD2

POD1

B32B-PHDSS-B

DSW-F

MSW

SUB P/S

B28B-PHDSS-B

TLS

TH-C L

PTDL

DMS

ADU

RRC

MOTH

HUS-D V

DV

TCS

DV

HPLS

CN-1 2

TFSD TNCA

CRUM

CN-11

VPM

TRM

2

1

POM2

POM1

CN-10

CN-9

CFM-U4

CN-8

CN-7 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31

+24V1 /HPLS DVCH1 DVCH2 DVCH3 DVCH4 +24V1 TCS GND2 TSGOUT GND2 +5V2 HUS-DV GND2 TH-DV

GND2 +5V2 CRUCLK CRUSDA GND2 TNCA

/POM1XA /POM1XB /POM2XA /POM2XB /1XA /1XB /2XA /2XB /TRMXA /TRMXB /VPMXA /VPMXB (NC)

12 14 16 18 20 22 24 26 28 30

11 13 15 17 19 21 23 25 27 29

1 3 5 7 10 9

2 4 6 8

2 1 4 3 6 5 8 7 10 9 12 11

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25

+5VS 2 1 PROFF-CNT 4 3 FWP-PCU 6 5 8 7 /DCCNT DTR-PCU 10 9 12 11 GND2 14 13 PAGE GND2 16 15 18 17 HSYNC GND2 20 19 22 21 GND2 GND2 24 23

/DMS-LED 2 1 4 3 DMS 6 5 +12V2 8 7 +24V1 10 9 /PTDL 12 11 TH-CL 14 13 GND2 16 15 TLS GND2 18 17 /PWM-RSV1 20 19

DSW-L

+24V1 /RRC (NC) +24V(DSW) PFD2 /CFM-ADU THPS2 TURM /TCB-PWM GND2 /TCBIAS APPD1 APPD2 AINPD GND2

GND2 MPRD1 +5V-MPRD2 GND2 MPRD2

+24V1 /T2PFC +24V1 /HPFC +24V1 /PSBC +5V2 PPD GND2 +5V-MPRD1

TM1a TM1b TM2a TM2b +24V1 TFSD

/POM1A /POM1B /POM2A /POM2B /1A /1B /2A /2B /TRMA /TRMB /VPMA /VPMB (NC)

/PRON-FAX /POF /MSW-OFF RES-PCU TXD-PCU GND2 DSR-PCU GND2 RXD-PCU GND2 VIDEOin+ VIDEOin-

/PCS-LED PCS +12V2 +24V-DL /DL +24V1 /PSPS +5V2 HUS-TC GND2

(NC)

+24V1 /CFM-DV GND2 +24V1 +5V-APPD1 +5V-APPD2 +5V-PFD2 +5V-DSW +5V-AINPD (NC) +5V-THPS2 /FBIAS DSW-ADU /DGS GND2

MPRD2

MPRD1

PPD

PSBC

HPFC

T2PFC

B30B-PHDSS-B

TFSD

TM2

TM1

B12B-PHDSS-B

VPM

TRM

2

1

POM2

POM1

B26B-PHDSS-B

MOTH

B24B-PHDSS-B

HUS-TC

PSPS

DL

PCS

B20B-PHDSS-B

ADU

CFM-DV

B32B-PHDSS-B

HV

DSW-DSK

TSW

MM

DSKPFC2

T1PFC

CN-17

M1PWS

DSKPFC1

M2PFD

M2LUD

M2PED

M2PUS

CN-16

M2SPD

M2SS

CN-15

T2SPD

T1SPD

DSKLS

T2PUS

T2LUM

CN-14

MPF

CN-13

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25

T2LUD T2PED

T1LUM GND2 +24V1 /T1PUS +5V2 GND2 T1LUD T1PED +5V2 GND2

DSW-F(R) (NC) +24V1 /MFPUS GND2 MPED +5V2 +24V1 /MPFGS +5V-MPFD1 MPFD1 GND2 (NC)

+5V2

+24V1 /T1PFC +24V1 /DSKPFC2 GND2 +5V2 /MM MMCLK MM-T TSW-LED TSW GND2 GND2 DSW-DSK

M2PFD +24V1 /DSKPFC1 Vref GND2 M1PWS

+24V1 /M2PUS GND2 M2PED +5V2 GND2 M2LUD +5V2 +5V-M2PFD GND2

+5V2

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31

TXD-FIN RXD-FIN /DTR-FIN /DSR-FIN RES-FIN (NC) GND2 TANSET +5V2 (NC)

M2LUM GND2 +24V1 /M2PFC GND2

+24V1 /M1PUS GND2 M1PED +5V2 GND2 M1LUD +5V2 +5V-M1PFD GND2 M1PFD +24 V1 /M1PFC M1LUM GND2 (NC)

34 33 +5V2

2 1 DSW-F (NC) 4 3 GND2 GND2 6 5 /GBPWM /MHVREM /THV+PWM 8 7 MHV-T /CHV-PWM 10 9 THV+REM /CHVAWM 12 11 /CHV-REM 14 13 /CHVACREM /DVPWM 16 15 /DVREM HVREM 18 17 +24V1 (NC) 20 19 GND2 GND2 22 21 M1SS1 M2SS1 24 23 M1SS2 M2SS2 26 25 M1SS3 M2SS3 28 27 M1SS4 M2SS4 30 29 GND2 GND2 32 31 M1SPD M2SPD

T2LUM GND2 +24V1 /T2PUS +24V1 / DSKLS GND2 T1SPD +5V2 GND2 T2SPD GND2

(NC) GND2 MPLD1 +5V2 MPLD2 MTOP1 MTOP2 MPFPWS Vref /MPFC +24V1 GND2 DSW-R

TANSET

FIN

/M2PFC

M2LUM

B30B-PHDSS-B

M1LUM

M1PFC

M1PFD

M1LUD

M1PED

M1PUS

B32B-PHDSS-B

M1SPD

M1SS

HV

B34B-PHDSS-B

T2LUD T2PED

T1LUD T1PED

T1PUS

T1LUM

B24B-P HDSS- B

MPF

B26B-PHDSS-B

CN-25 1 +5V-T1PPD 2 (NC) 3 T1PPD 4 (NC) 5 GND2 6 (NC)

CN-24 1 +5V-WEBENDD 2 WEBENDD 3 GND2 4 WEBMA 5 WEBMB 6 Reserve7

LSU

CN-22

TH-RA

CFM-R2

CN-21

CN-20 1 +24V1 2 +12V2 3 +5V2 4 +3.3V1 5 GND1 6 GND2 7 GND2 8 GND2 9 FW

DS

WH

WH-DV

CFM-DC2

CN-19

LPPD

MPFD2

CN-18

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23

2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29

2 1 4 3 6 5 8 7 10 9 12 11

T1PPD

B6B-PH-K-S

WEB

B6B-PH-K-S

+5VLD GND2 /PGMCLK +24V1 +24V1 GND2 GND2 TEST2 GND2 GND2 GND2 GND2 GND2 GND2 GND2

+24V1 /CFM-R2 GND2 (NC) TH-RA GND2

POWER

B9P-VH

+24V1 /CFM-DC2 GND2 /WHPR1 +24V1 GND2 +38V-MON GND2 /WHPR2 +24V1 (NC) /DCCNT

+5V-MPFD2 2 1 4 3 GND2 6 5 MPFD2 +5V-LPPD 8 7 GND2 10 9 12 11 LPPD 14 13 (NC)

GND2 GND2 /READY /START (NC) +5V2 +5V2 TEST VRB TEST3 VIDEO /VIDEO LSUS/H /LDON /SYNC

/CFM-R1 GND2 +24V1 /CFM-R3 GND2

+24V1

+24V1 /CFM-DC1 GND2 +12VS BUP-PR GND2 +24V-INT INTPR GND2 INTPR2 GND2 /MSW-MON

GND2 TXD-LCC RXD-LCC /DTR-LCC /DSR-LCC RES-LCC /TRC-LCC

LSU

B30B-PHDSS-B

CFM-R3

CFM-R1

B12B -PHD SS-B

DS

AC

CFM-DC1

B24B-PHDSS-B

LCC

B14B-PHDSS-B

J. PCU connector table

4. Signal name list Signal name /MIMA /MIMB /SLUMB

/SLUMA

/SPFMA /SPFMB /VIDEO 38VMON ACMON

ADD_CCD1 ADD_CCD2 1A

1B

1XA

1XB

2A

2B

2XA

2XB

AINPD

APPD1 APPD2 AUD BUP-PRout BZR CA CCDFAN CCFT CFM-DC1 CFM-DC2 CFM-DV CFM-R1 CFM-R2

Name Scanner motor control signal (Phase /A) Scanner motor control signal (Phase /B) DDSPF paper feed tray lift-up motor control signal (Phase /B) DSPF paper feed tray lift-up motor control signal (Phase /A) DSPF motor control signal (Phase /A) DSPF motor control signal (Phase /B) Image data signal 38V monitor signal AC waveform monitor signal

CCD serial data area identification number (CCD) CIS serial data area identification number (CIS) Duplex (ADU) motor 1 (Upstream side) control signal (Phase A) Duplex (ADU) motor 1 (Upstream side) control signal (Phase B) Duplex (ADU) motor 1 (Upstream side) control signal (Phase /A) Duplex (ADU) motor 1 (Upstream side) control signal (Phase /B) Duplex (ADU) motor 2 (Downstream side) control signal (Phase A) Duplex (ADU) motor 2 (Downstream side) control signal (Phase B) Duplex (ADU) motor 2 (Downstream side) control signal (Phase /A) Duplex (ADU) motor 2 (Downstream side) control signal (Phase /B) Duplex (ADU) paper entry detection signal Duplex (ADU) paper detection signal 1 Duplex (ADU) paper detection signal 2 Auditor installation detection signal Power save mode relay signal Buzzer signal Clear all (Auditor) signal CCD fan motor control signal Backlight control signal Cooling fan motor control signal (Power source) Cooling fan motor control signal (Power source) Cooling fan motor control signal (Developing) Cooling fan motor control signal (LSU/Process section) Cooling fan motor control signal (LSU/Process section)

Function/Operation Scanner motor control (Phase /A)

Connector level “L” “H” — —

Connector No.

Pin No.

PWB name

7

3

SCN

Scanner motor control (Phase /B)

—

—

7

4

SCN

DSPF paper feed tray lift-up motor control (Phase /B)

—

—

11

2

SCN

DSPF paper feed tray lift-up motor control (Phase /A)

—

—

11

1

SCN

DSPF motor control (Phase /A)

—

—

12

11

SCN

DSPF motor control (Phase /B)

—

—

12

15

SCN

Image signal to LSU (PCU output) Detection of 38V for interlock SUB power source AC wave high value monitor (For heater lamp ON control) (Phase control) Identification of address data and image data area in CCD serial data Identification of address data and image data area in CIS serial data Duplex (ADU) motor 1 (Upstream) control (Phase A)

— OFF —

— ON —

22 19 1

23 14 3

PCU PCU PCU

—

—

1

66

SCN

—

—

10

13

SCN

—

—

10

9

PCU

Duplex (ADU) motor 1 (Upstream) control (Phase B)

—

—

10

11

PCU

Duplex (ADU) motor 1 (Upstream) control (Phase /A)

—

—

10

10

PCU

Duplex (ADU) motor 1 (Upstream) control (Phase /B)

—

—

10

12

PCU

Duplex (ADU) motor 2 (Upstream) control (Phase A)

—

—

10

13

PCU

Duplex (ADU) motor 2 (Upstream) control (Phase B)

—

—

10

15

PCU

Duplex (ADU) motor 2 (Upstream) control (Phase /A)

—

—

10

14

PCU

Duplex (ADU) motor 2 (Upstream) control (Phase /B)

—

—

10

16

PCU

Duplex (ADU) paper entry detection, detection of paper exit to finisher Duplex (ADU) upstream paper detection Duplex (ADU) midstream paper detection Auditor installation detection

Paper

—

7

28

PCU

Paper

—

7

24

PCU

Paper

—

7

26

PCU

5

5

SCN

Relay ON

19

9

PCU

Stop

1 5 1 1 19

86 3 17 94 3

SCN SCN SCN SCN PCU

Stop

19

4

PCU

Stop

7

3

PCU

Stop

21

3

PCU

Stop

21

4

PCU

Selection of power save mode and normal power mode Key touch sound buzzer signal Clear all (Auditor) CCD fan motor control Backlight control Power cooling fan motor control Power cooling fan motor control Developing cooling fan motor control Cooling fan motor control (LSU, process section) Cooling fan motor control (LSU, process section)

Counter available Relay OFF Ring Clear ON ON Max. force of wind Max. force of wind Max. force of wind Max. force of wind Max. force of wind

MX-M700N ELECTRICAL SECTION 11 – 18

Remark

Not used.

Signal name CFM-R3 CFM-U1 CFM-U2

CFM-U3

CHVAWM CHVACREM CHV-PWM CHV-REM CISSET CISTH CL1 CLK_CCD1 CLK_CCD2 COPY CRUCLK CRUSDA CV_CA CV_COPY CV_COUNT CV_DUPLEX

CV_SIZE0 CV_SIZE1 CV_SIZE2 CV_SIZE3 CV_STAPLE CV_START DCCNT DGS DL DM

DMCLK DMS DMS-LED DM-T DSKPFC1

DSKPFC2

Name Cooling fan motor control signal (LSU/Process section) Cooling fan motor control Cooling fan motor control signal (Paper exit, duplex (ADU) section) (Paper exit section rear side) Cooling fan motor control signal (Paper exit, duplex (ADU) section) (Front surface) High voltage control output (Separation charger) (CHV) High voltage control output (Separation charger) (CHV) High voltage control output (Separation charger) (CHV) High voltage control output (Separation charger) (CHV) CIS identification signal CIS temperature detection signal Scanner lamp control signal CCD serial data clock signal (CCD) CIS serial data clock signal (CIS) Copy status (Auditor) Communication CLK Communication data address signal Clear all signal (Coin vendor) Copy enable signal (Coin vendor) Count up signal (Coin vendor) Print count identification signal (Duplex mode) (For coin vendor) Paper size signal 0 (Coin vendor) Paper size signal 1 (Coin vendor) Paper size signal 2 (Coin vendor) Paper size signal 3 (Coin vendor) Staple mode signal (Coin vendor) Copy start signal (Coin vendor) DC power control signal Paper exit gate solenoid control signal Discharge lamp control signal OPC drum motor rotating speed control signal (ON/OFF) OPC drum motor rotating speed control (CLK) signal OPC drum marking sensor signal OPC drum marking sensor LED control signal OPC drum motor lock detection signal Paper feed tray 3/4 paper transport clutch control signal 1 Paper feed tray 3/4 paper transport clutch control signal 2

Cooling fan motor control (LSU, process section) Cooling fan motor control (LSU, process section) Paper exit, duplex (ADU) section cooling

Connector level “L” “H” Max. force Stop of wind Max. force Stop of wind Max. force Stop of wind

Paper exit, duplex (ADU) section cooling

Max. force of wind

Stop

5

27

PCU

—

—

15

12

PCU

ON

OFF

15

13

PCU

—

—

15

10

PCU

ON

OFF

15

11

PCU

CIS available —

—

10

26

SCN

—

13

1

SCN

ON —

— —

1 1

71 62

SCN SCN

—

—

10

11

SCN

Copying — —

— — —

5 11 11

2 6 8

SCN PCU PCU

Clear Copy enable Count UP Duplex mode

—

4 4

6 3

SCN SCN

4 4

4 8

SCN SCN

4

9

SCN

Paper size 1 (Coin vendor)

4

10

SCN

Paper size 2 (Coin vendor)

4

11

SCN

Paper size 3 (Coin vendor)

4

12

SCN

4

7

SCN

4

5

SCN

9–8 19 – 24 7 27

PCU PCU

Function/Operation

Separation charger AC component PWM control Separation charger AC component ON/OFF control Separation charger DC component PWM control Separation charger DC component ON/OFF control CIS unit installation detection CIS temperature detection Scanner lamp control CD serial data output timing control (CCD) CIS serial data output timing control (CIS) Copy status signal (Auditor) CRUM communication CLK CRUM communication data address signal Clear all (Coin vendor) Copy enable (Coin vendor) Count-up (Coin vendor) Print count identification signal (Duplex mode) (For coin vendor) (Identification of single count or double count) Paper size 0 (Coin vendor)

Staple mode identification (Coin vendor) Copy start status (Coin vendor) DC power ON/OFF

Staple mode Copy start

Connector No.

Pin No.

PWB name

21

9

PCU

5

21

PCU

5

28

PCU

OFF

ON

Duplex

Simplex

Discharge lamp control OPS drum motor ON/OFF

ON ON

OFF OFF

8 6

9 5

PCU PCU

OPC drum motor RPM control

—

—

6

7

PCU

OPC drum mark detection

—

—

8

4

PCU

OPC drum marking LED light quantity control OPC drum motor lock detection

—

—

8

2

PCU

Rotation

Stop/Lock

6

9

PCU

Paper feed tray 3/4 paper transport control

Paper transport

—

16

26

PCU

Paper feed tray 3/4 paper transport control

Paper transport

—

17

8

PCU

Paper exit gate control

MX-M700N ELECTRICAL SECTION 11 – 19

Remark

Not used.

Refer to the separate table (*2)

Signal name DSR_FIN DSR_LCC DSR_SCN DSW-ADU

DSW-DSK DSW-F_HV

DSW-F

DSW-L DSW-R

DTR_FIN DTR_LCC DTR_SCN DVCH1 DVM DVMCLK DVM-T DVPWM DVREM F0 F1 F2 F3 FBIAS FRDY FRM_CCD1 FRM_CCD2 FUM FUMCLK FUM-T FW FW_SUB FWP-PCU GBPWM HLCNT1 HLCNT2

Name Serial communication control signal Serial communication control signal Serial I/F send enable (MFP) Duplex (ADU) cover open/ close detection signal Left door open/close detection signal (Desk section) DC low voltage power (+24V) line signal for generating high voltage Front door open/close detection signal

Left door open/close detection signal Manual feed open/close detection signal

Serial communication control signal Serial communication control signal Serial I/F receive enable signal (MFP) DV unit identification signal 1 Developing motor control signal Developing motor rotating speed control (CLK) signal Developing motor lock detection signal Developing bias voltage control signal (PWM) Developing bias control (ON/OFF) signal Operation LED matrix signal 0 Operation LED matrix signal 1 Operation LED matrix signal 2 Operation LED matrix signal 3 Fusing bias output control signal FAX LED lighting signal CCD image data effective area signal (CCD) CIS image data effective area signal (CIS) Fusing motor control signal Fusing motor rotating speed control (CLK) signal Fusing motor lock detection signal AC power source full wave signal Sub power source full wave signal Flash write protect signal Making charger grid bias voltage (PWM) control signal Upper fusing roller center heater lamp control signal Upper fusing roller center heater lamp control signal

Function/Operation Receive control Receive control

Connector level “L” “H” — —

Connector No.

Pin No.

PWB name

17

17

PCU

—

—

18

9

PCU

— Duplex (ADU) door open Desk left door open —

— Duplex (ADU) door close Desk left door close High voltage available

9 7

46 25

SCN PCU

17

28

PCU

15

1

PCU

Left door close and Front door close Left door close Left door close and Front door closeand manual unit insertion —

2

28

PCU

7

32

PCU

13

26

PCU

Send control

Left door open or Front door open Left door open Left door open or Front door open or manual unit pull-out —

17

15

PCU

Send control

—

—

18

7

PCU

Send control

—

—

9

9

SCN

Detection of installation Developing motor ON/OFF

— ON

— OFF

12 6

6 6

PCU PCU

Developing motor control RPM control Developing motor lock detection

—

—

6

8

PCU

Rotation

Stop/Lock

6

10

PCU

Developing bias PWM control

—

—

15

14

PCU

Developing bias ON/OFF

ON

OFF

15

15

PCU

Switching

—

—

1

78

SCN

Switching

—

—

1

80

SCN

Switching

—

—

1

82

SCN

Switching

—

—

1

84

SCN

Fusing bias output ON/OFF control

ON

OFF

7

23

PCU

LED ON

9

14

SCN

—

—

1

61

SCN

—

—

10

10

SCN

ON —

OFF —

6 6

13 14

PCU PCU

Rotation

Stop/Lock

6

15

PCU

Power monitor

—

—

20

9

PCU

Sub power full wave signal

—

—

1

4

PCU

Flash write protect Main charger grid bias voltage (PWM) control Upper fusing roller center heating control Upper fusing roller edges heating control

— —

— —

9 15

6 5

PCU PCU

OFF

ON

2

9

PCU

OFF

ON

2

11

PCU

Receive control Duplex (ADU) cover open/close detection Left door open/close detection (Desk section) High voltage power source (+24V)

Front door open/close detection

Left door open/close detection Manual feed open/close detection

LED lighting control in power save mode i FAX, FAX, nighttime mode CCD image data effective area control (CCD) CIS image data effective area control (CIS) Fusing motor ON/OFF Fusing motor control CLK Fusing motor lock detection

MX-M700N ELECTRICAL SECTION 11 – 20

Remark

Signal name HLCNT3

Name

HSYNC HUS-DV

Sub heat roller heater lamp control signal Fusing heater lamp power relay control signal Fusing heater lamp power relay 3 control signal Horizontal paper transport clutch control signal Paper guide lock solenoid control signal Horizontal sync signal Developing humidity sensor

HUS-TC

Transfer humidity sensor

HVREMout

High voltage control output control signal (MC/DV/TC) Interlock power relay "RY5" control signal Interlock power relay "RY4" control signal Laser ON/OFF control signal Document size detection LED control signal 1 Document size detection LED control signal 0 LCC paper detection signal Laser beam horizontal sync signal Paper tray upper limit detection signal (Paper feed tray 3) Lift-up motor control signal (Paper feed tray 3) Paper empty detection signal (Paper feed tray 3) Paper feed clutch (M1) control signal (Paper feed tray 3) Paper detection signal (Multi paper feed tray 3) Paper pickup solenoid control signal (Paper feed tray 3) Paper feed tray paper width detection signal (Paper feed tray 3) Paper remaining quantity detection signal (Paper feed tray 3)

HLPRout HLPRout3 HPFC HPLS

INTPR2out INTPRout LDON LED0 LED1 LPPD LSU_S/H M1LUD

M1LUM M1PED M1PFC M1PFD M1PUS M1PWS

M1SPD

M1SS1 M1SS2 M1SS3 M1SS4 M2LUD

M2LUM M2PED M2PFC M2PFD M2PUS

Paper size detection signal (Paper feed tray 3) Paper size detection signal (Paper feed tray 3) Paper size detection signal (Paper feed tray 3) Paper size detection signal (Paper feed tray 3) Paper tray upper limit detection signal (Paper feed tray 4) Lift-up motor control signal (Paper feed tray 4) Paper empty detection signal (Paper feed tray 4) Paper feed clutch (M1) control signal (Paper feed tray 4) Paper detection signal (Multi paper feed tray 4) Paper pickup solenoid control signal (Paper feed tray 4)

Function/Operation Sub heat roller heater lamp control Fusing heater lamp power relay control Fusing heater lamp power relay 3 control Horizontal paper transport clutch control Paper guide lock solenoid control

Connector level “L” “H” OFF ON

Connector No.

Pin No.

PWB name

1

5

PCU

Relay OFF

Relay ON

2

5

PCU

Relay OFF

Relay ON

2

7

PCU

Paper transport Lock

—

12

7

PCU

—

12

4

PCU

— —

— —

9 12

18 26

PCU PCU

—

—

8

17

PCU

OFF

ON

15

16

PCU

Relay OFF

Relay ON

19

19

PCU

Relay OFF

Relay ON

19

15

PCU

— —

— —

22 3

27 5

PCU SCN

—

—

3

6

SCN

Paper

—

18

12

PCU

—

—

22

25

PCU

Upper limit

—

16

13

PCU

Stop

Up

16

27

PCU

Paper empty Paper transport Paper

Paper present —

16

7

PCU

16

25

PCU

—

16

21

PCU

Roller UP

Paper feed

16

3

PCU

—

—

16

32

PCU

Paper remaining quantity detection (Multi paper feed tray 3)

—

15

31

PCU

Paper size detection (Paper feed tray 3) Paper size detection (Paper feed tray 3) Paper size detection (Paper feed tray 3) Paper size detection (Paper feed tray 3) Paper tray upper limit detection (Paper feed tray 4)

—

Remaining paper quantity 66% or less —

15

21

PCU

—

—

15

23

PCU

—

—

15

25

PCU

—

—

15

27

PCU

—

Upper limit detection

16

14

PCU

Stop

Up

17

1

PCU

Paper empty Paper transport Paper

Paper present —

16

8

PCU

17

7

PCU

—

16

22

PCU

Roller UP

Paper feed

16

4

PCU

Horizontal sync Developing section peripheral humidity detection Transfer section peripheral humidity detection High voltage ON/OFF control signal (MC/DV/TC) AC PWB relay "RY5" control (38V line interlock relay) AC PWB relay "RY4" control (38V line interlock relay) Laser ON/OFF control Document size detection LED control Document size detection LED control Detection of paper entry from LCC Laser beam horizontal position timing control Paper tray upper limit detection (Paper feed tray 3) Lift-up motor control (Paper feed tray 3) Paper empty detection (Paper feed tray 3) Paper feed tray 3 paper feed control Paper feed tray 3 paper detection Paper pickup roller control (Paper feed tray 3) Multi paper feed tray paper width detection (Paper feed tray 3)

Lift-up motor control (Paper feed tray 4) Paper empty detection (Paper feed tray 4) Paper feed tray 4 paper feed control Paper feed tray 4 paper detection Paper pickup roller control (Paper feed tray 4)

MX-M700N ELECTRICAL SECTION 11 – 21

Remark

Refer to the separate table (*1)

Signal name

Name

Function/Operation

M2SPD

Paper remaining quantity detection (Paper feed tray 4) signal

Paper remaining quantity detection (Paper feed tray 4)

M2SS1

Paper size detection signal (Paper feed tray 4) Paper size detection signal (Paper feed tray 4) Paper size detection signal (Paper feed tray 4) Paper size detection signal (Paper feed tray 4) Paper pickup solenoid (MFP) control signal (Manual paper feed) Scanner home position sensor signal Main charger control signal Main charger trouble detection signal Scanner motor control signal (Phase A) Scanner motor control signal (Phase B) Main motor control signal Main motor rotating speed control (CLK) signal Main motor lock detection signal Manual feed paper empty detection signal Paper feed clutch control signal (Manual feed) Manual feed paper detection signal 1 Manual feed paper detection signal 2 Manual feed gate solenoid control signal Manual feed paper width detection signal Manual feed paper length detection signal 1 Manual feed paper length detection signal 1 Paper feed tray 2 paper detection signal 1 Paper feed tray 2 paper detection signal 2 MSW monitor signal MSW OFF signal Main switch power relay control signal Manual tray pull-out position detection signal 1 Manual tray pull-out position detection signal 2 DSPF open/close detection signal Page signal

Paper size detection (Paper feed tray 4) Paper size detection (Paper feed tray 4) Paper size detection (Paper feed tray 4) Paper size detection (Paper feed tray 4) Paper pickup solenoid (MPF) control (Manual paper feed)

M2SS2 M2SS3 M2SS4 MFPUS

MHPS MHVREM MHV-T MIMA MIMB MM MMCLK MM-T MPED MPFC MPFD1 MPFD2 MPFGS MPFPWS MPLD1 MPLD2 MPRD1 MPRD2 MSWMON MSWOFF MSWPR MTOP1 MTOP2 OCSW PAGE PAGE1 PAGE2 PCS PCS-LED PCU_DSR PCU_DTR

Image effective area signal (CCD) Image effective area signal (CIS) Image density sensor signal Image density sensor LED current control signal Serial communication control signal Serial communication control signal

Scanner home position detection Main charger ON/OFF Main charger trouble detection

Connector level “L” “H” — Remaining paper quantity 66% or less — —

Connector No.

Pin No.

PWB name

15

32

PCU

15

22

PCU

—

—

15

24

PCU

—

—

15

26

PCU

—

—

15

28

PCU

Paper feed with the roller down —

—

13

7

PCU

Home position OFF Normal

6

1

SCN

15 15

6 7

PCU PCU

—

7

1

SCN

Scanner motor control (Phase A)

ON Trouble, no MHV —

Scanner motor control (Phase B)

—

—

7

2

SCN

Main motor ON/OFF control Main motor RPM control

ON —

OFF —

17 17

14 16

PCU PCU

Rotation

Stop/Lock

17

18

PCU

Manual paper feed tray paper empty detection Manual feed tray paper feed roller control Manual tray paper detection

Paper present Paper feed

Paper empty

13

11

PCU

—

13

20

PCU

—

Paper

13

21

PCU

Manual tray and LCC paper detection Manual feed gate control

Paper

—

18

6

PCU

Paper enable —

Stopper

13

17

PCU

—

13

16

PCU

—

13

6

PCU

13

10

PCU

Paper

Paper present Paper present —

12

23

PCU

Paper

—

12

29

PCU

— — Relay ON

— — Relay OFF

19 9 2

23 5 15

PCU PCU PCU

Store

—

13

12

PCU

Pull out

—

13

14

PCU

Close

—

3

3

SCN

—

—

9

14

PCU

—

—

1

68

SCN

—

—

10

12

SCN

—

—

8

3

PCU

—

—

8

1

PCU

—

—

9

13

PCU

—

—

9

10

PCU

Main motor lock detection

Manual feed paper width detection Manual paper feed tray paper length detection (Short) Manual paper feed tray paper length detection (Long) Manual feed/paper feed tray 2/ LCC paper detection Manual feed/paper feed tray 2/ LCC paper detection Main switch monitor Main switch OFF signal Main switch power relay control Manual paper feed tray pull-out position detection (Storing position) Manual paper feed tray pull-out position detection (Pull-out position) Document size detection trigger Print timing control for controller (Output for every page) Indicates image data area of one page. (CCD) Indicates image data area of one page. (CIS) Detection of density of toner patch on the OPC drum Image density sensor LED light emitting quantity control Send control signal (Serial communication) Receive control signal (Serial communication)

—

MX-M700N ELECTRICAL SECTION 11 – 22

Remark

Refer to the separate table (*1)

Signal name

Name

Function/Operation

PCU_RES

PCU reset signal

PCU reset by the controller

PCU_RXD

Serial communication send data signal Serial communication receive data signal Document size detection signal Document detection select signal 0 Document detection select signal 1 Document detection select signal 2 Paper detection signal 2

Send data to the controller

PCU_TXD PD PDSEL0 PDSEL1 PDSEL2 PFD2

PGMCLK

POD1 POD2

LSU motor RPM control signal (CLK) Count-up signal (Auditor) Count-up signal (Personal counter) Paper exit detection 1 signal Paper exit detection 2 signal

POD3

Paper exit detection 3 signal

POF POF_SCN

Power OFF status signal Power off signal

POM1A

Paper exit motor 1 (Fusing side) control signal (Phase A) Paper exit motor 1 (Fusing side) control signal (Phase B) Paper exit motor 1 (Fusing side) control signal (Phase /A) Paper exit motor 1 (Fusing side) control signal (Phase /B) Paper exit motor 2 (Paper exit side) control signal (Phase A) Paper exit motor 2 (Fusing side) control signal (Phase B) Paper exit motor 2 (Fusing side) control signal (Phase /A) Paper exit motor 2 (Fusing side) control signal (Phase /B) Resist roller front paper detection signal BUP-PR control signal (Main power OFF signal) BUP-PR control signal (Main power ON signal) Resist roller brake clutch control signal

PNC PNC-a

POM1B POM1XA POM1XB POM2A POM2B POM2XA POM2XB PPD PROFF_CNT PRON_FAX PSBC

PSPS

Pin No.

PWB name

9

7

PCU

9

17

PCU

—

—

9

9

PCU

OC document size detection analog signal Document size detection signal select Document size detection signal select Document size detection signal select Paper detection (Left door unit) from duplex (ADU)/ No. 1, 3, 4 paper feed tray LSU motor RPM control

—

—

1

74

SCN

—

—

1

72

SCN

—

—

1

21

SCN

—

—

1

22

SCN

Paper

—

7

10

PCU

—

—

22

6

PCU

Count UP —

— —

5 2

1 20

SCN PCU

Paper Paper

— —

5 5

3 9

PCU PCU

—

5

15

PCU

Power OFF Power OFF

Paper (Full detection) Power ON —

9 9

3 43

PCU SCN

—

—

10

1

PCU

—

—

10

3

PCU

—

—

10

2

PCU

—

—

10

4

PCU

—

—

10

5

PCU

—

—

10

7

PCU

—

—

10

6

PCU

—

—

10

8

PCU

Paper

—

12

15

PCU

—

End

9

4

PCU

Boot

—

9

1

PCU

—

Paper transport enable —

12

11

PCU

8

13

PCU

Stop

8

20

PCU

Stop/Lock

22

5

PCU

—

5

4

SCN

Reset Reset Reset

1 10 17

64 15 19

SCN SCN PCU

Reset

18

11

PCU

— —

9 9

12 44

SCN SCN

Count up (Auditor) Count up (Personal counter) Paper exit detection from fusing Paper detection from paper exit Paper exit detection to upper section paper exit tray (Full detection) Power OFF status Power OFF status signal (Output from PCU) Paper exit unit (Fusing side) paper transport Paper exit unit (Fusing side) paper transport Paper exit unit (Fusing side) paper transport Paper exit unit (Fusing side) paper transport Paper exit unit (paper exit side) paper transport Paper exit unit (paper exit side) paper transport Paper exit unit (paper exit side) paper transport Paper exit unit (Paper exit side) paper transport Paper detection in front of resist roller Main power OFF signal (output from controller) Main power ON signal (Output front FAX unit) Resist roller brake clutch control

READY

Copy enable (Auditor)

RES_CCD1 RES_CCD2 RES_FIN

Reset signal (CCD) Reset signal (CIS) Finisher reset signal

Reset (CCD) Reset (CIS) Finisher reset

RES_LCC

LCC reset signal

LCC reset

RES_MFP RES_SCN

Main unit reset signal (MFP) Scanner reset signal

Not used. Scanner reset (output from controller)

READY

Connector No.

Receive data from the controller

Separation solenoid control signal Cooling fan motor control signal (Paper exit duplex (ADU) section (Top surface)) LSU motor lock detection signal Copy enable signal (Auditor)

PWM-RSV1

Connector level “L” “H” Operation Reset enable — —

Separation solenoid control Paper exit, duplex (ADU) section cooling LSU motor lock detection

Separation Max. blowing capacity Rotation Copy enable — — Operation enable Operation enable Reset Reset

MX-M700N ELECTRICAL SECTION 11 – 23

Remark

Signal name

Name

RRC

Resist roller clutch control signal

RTH1

RXD_CCD1

Heat roller temperature detection signal Pressure roller temperature detection signal Sub heat roller temperature detection signal Serial I/F data (CCD)

RXD_CCD2

Serial I/F data (CIS)

RXD_FIN RXD_LCC RXD_SCN

Serial I/F data (FINISHER) Serial I/F data (LCC) Serial I/F data (Scanner control PWB) Scanner control PWB identification signal DSPF cover switch signal Operation LED matrix signal 0 Operation LED matrix signal 1 Operation LED matrix signal 2 Energy-saving mode display signal DSPF tray lift-up motor control signal (Phase A) DSPF tray lift-up motor control signal (Phase B) DSPF open/close detection signal DSPF document empty detection signal DSPF document detection signal DSPF paper feed clutch control signal DSPF fan motor control signal DSPF paper feed, paper transport motor control signal (Phase A) DSPF paper feed, paper transport signal (Phase B) DSPF paper feed, paper transport motor current control signal 1 DSPF paper feed, paper exit motor current control signal 2 DSPF identification signal

RTH2 RTH3

SCNSET SCOV SEG0 SEG1 SEG2 SLEEP SLUMA SLUMB SOCD SPED1 SPED2 SPFC SPFFAN SPFMA

SPFMB SPFMO1

SPFMO2 SPFSET SPLS1 SPLS2 SPOD SPPD1 SPPD2 SPPD3 SPPD4 SPWS SRRBC SRRC START

DSPF document length detection signal 1 DSPF document length detection signal 2 DSPF paper exit detection signal DSPF document paper detection 1 signal DSPF document paper detection 2 signal DSPF document paper detection 3 signal DSPF document paper detection 4 signal DSPF document size (Width) detection analog data signal DSPF resist roller brake clutch control signal DSPF resist roller clutch control signal LSU motor control signal

Function/Operation Resist roller clutch control (The relative position of print image and paper is controlled.) Heat roller temperature detection (Center section) Pressure roller temperature detection (Edge section) Sub heat roller temperature detection Serial I/F data (CCD-scanner control PWB) Serial I/F data (CCD-scanner control PWB) Serial I/F data (Finisher-PCU PWB) Serial I/F data (LCC-PCU PWB) Serial I/F data (Scanner control PWB - Controller) Scanner control PWB installation detection DSPF cover open/close detection Operation LED matrix

Connector level “L” “H” Paper — transport

Connector No.

Pin No.

PWB name

7

4

PCU

—

—

2

6

PCU

—

—

2

10

PCU

—

—

2

14

PCU

—

—

1

65

SCN

—

—

10

16

SCN

— — —

— — —

17 18 9

13 5 45

PCU PCU SCN

Scanner available — —

—

9

47

SCN

Close —

12 1

8 24

SCN SCN

Operation LED matrix

—

—

1

75

SCN

Operation LED matrix

—

—

1

76

SCN

LED lighting signal in energy saving mode DSPF tray lift-up motor control (Phase A) DSPF tray lift-up motor control (Phase B) DSPF open/close detection

—

LED ON

9

15

SCN

—

—

11

3

SCN

—

—

11

4

SCN

Close

11

19

SCN

12

12

SCN

11

14

SCN

ON

11

10

SCN

DSPF document empty detection DSPF document detection

Paper present Paper present

DSPF paper feed clutch control DSPF fan motor control DSPF paper feed, paper transport motor control (Phase A)

ON —

—

11 12

11 13

SCN SCN

DSPF paper feed, paper transport motor control (Phase B) DSPF paper feed, paper transport motor current control

—

—

12

17

SCN

Power down

12

16

SCN

Power down DSPF available

12

18

SCN

11

5

SCN

11

18

SCN

11

17

SCN

Paper exit

11

20

SCN

Paper present Paper present Paper present Paper present —

12

10

SCN

12

6

SCN

11

13

SCN

11

12

SCN

—

11

16

SCN

ON

11

6

SCN

ON

11

7

SCN

OFF

22

7

PCU

DSPF paper feed, paper transport motor current control DSPF installation detection DSPF document length detection (Short) DSPF document length detection (Long) DSPF paper exit detection DSPF document paper detection 1 DSPF document paper detection 2 DSPF document paper detection 3 DSPF document paper detection 4 DSPF document size (Width) detection DSPF resist roller brake clutch control DSPF resist roller clutch control LSU motor ON/OFF

Paper present Paper present

ON

MX-M700N ELECTRICAL SECTION 11 – 24

Remark

Signal name STLD STMPS STRBC STRC STRRBC STRRC STSET STUD SYNC T1LUD

T1LUM T1PED T1PFC T1PPD T1PUS T1SPD

T2LUD

T2LUM T2PED T2PFC T2PUS T2SPD

TANSET TCBIAS TCBPWM TCS TFSD

TH TH-CL TH-DV TH-EX THPS1

THPS2

Name

Function/Operation

DSPF document tray lower limit detection signal Stamp solenoid control signal DSPF paper transport clutch control signal DSPF paper transport clutch control signal DSPF paper transport resist brake clutch control signal DSPF paper transport resist clutch control signal Stamp identification signal

DSPF document tray lower limit detection Stamp solenoid control DSPF paper transport roller brake clutch control DSPF paper transport clutch control DSPF paper transport resist brake clutch control DSPF paper transport resist clutch control Stamp Yes/No detection

DSPF document tray upper limit detection signal LSU horizontal sync detection signal Paper feed tray upper limit detection signal (Paper feed tray 1) Paper tray lift-up motor control signal (Paper feed tray 1) Paper empty detection signal (Paper feed tray 1) Paper feed clutch control signal (Paper feed tray 1) Paper detection signal (Paper feed tray 1) Paper pick-up solenoid control signal (Paper feed tray 1) Paper remaining quantity detection signal (Paper feed tray 1)

DSPF document tray upper limit detection LSU horizontal sync detection (BD sensor signal) Paper feed tray upper limit (Paper feed tray 1)

Paper tray upper limit detection signal (Paper feed tray 2) Paper tray lift-up motor control signal (Paper feed tray 2) Paper empty detection signal (Paper feed tray 2) Paper clutch control signal (Paper feed tray 2) Paper pickup solenoid control signal (Paper feed tray 2) Paper remaining quantity detection signal (Paper feed tray 2)

Paper tray upper limit detection (Paper feed tray 2)

Paper tray lift-up control (Paper feed tray 1) Paper presence detection (Paper feed tray 1) Paper feed clutch control (Paper feed tray 1) Paper detection from paper feed tray 1 Paper pickup solenoid control (Paper feed tray 1) Paper remaining quantity detection (Paper feed tray 1)

Paper tray lift-up motor control (Paper feed tray 2) Paper presence detection (Paper feed tray 2) Paper feed clutch control (Paper feed tray 2) Paper pickup solenoid control (Paper feed tray 2) Paper remaining quantity detection (Paper feed tray 2)

Paper feed tray 1/2 (Tandem tray) detection signal Transfer belt cleaning output control signal (ON/OFF) Transfer belt cleaning output control signal (PWM) Toner density detection signal Toner remaining quantity detection signal

Paper feed tray 1, 2 (Tandem tray) insertion detection Transfer belt cleaning bias ON/ OFF control Transfer belt cleaning bias output voltage PWM control Toner density detection Toner hopper remaining quantity detection

LCD temperature sensor signal OPC drum cleaner temperature sensor signal Developing humidity detection signal Paper exit unit temperature sensor Transfer belt / separation home position sensor 1 Transfer belt / separation home position sensor 2

LCD temperature detection OPC drum cleaner peripheral temperature detection Developing section humidity detection Paper exit unit peripheral temperature detection Transfer belt separation home position detection 1 Transfer belt separation home position detection 2

Connector level “L” “H” Lower limit

Connector No.

Pin No.

PWB name

11

15

SCN

Stamp ON ON

1 11

48 9

SCN SCN

ON

11

8

SCN

ON

12

20

SCN

ON

12

19

SCN

1

47

SCN

Upper limit

12

14

SCN

—

—

22

29

PCU

Upper limit

—

14

13

PCU

Stop

Up

14

1

PCU

Paper empty Paper transport Paper

Paper present —

14

15

PCU

17

4

PCU

—

25

3

PCU

Roller UP

Paper feed

14

7

PCU

—

14

16

PCU

Upper limit

Remaining paper quantity 66% or less —

14

21

PCU

Stop

Up

14

2

PCU

Paper empty Paper transport The roller lifts up. —

Paper present —

14

23

PCU

12

3

PCU

Paper feed

14

8

PCU

14

22

PCU

Pull out

Remaining paper quantity 66% or less Insert

17

25

PCU

ON

OFF

7

22

PCU

—

—

7

18

PCU

— Remaining quantity large —

— Remaining quantity small —

12 11

16 11

PCU PCU

1

93

SCN

—

—

8

12

PCU

—

—

12

30

PCU

—

—

5

31

PCU

—



7

6

PCU

—



7

14

PCU

Stamp available

MX-M700N ELECTRICAL SECTION 11 – 25

Remark

Not used.

Signal name TH-RA THV+PWM THV+REM TLS TM1A TM1B TM2A TM2B TNCA TRC_LCC TRMA

Name Machine temperature detection signal Transfer charger output control signal (THV) Transfer charger control signal (THV) Waste toner pipe lock detection signal Toner motor 1 control signal Toner motor 1 control signal Toner motor 2 control signal Toner motor 2 control signal Waste toner full detection signal LCC paper feed timing signal

TXD_CCD1

Transfer roller 15 drive motor control signal (Phase A) Transfer roller 15 drive motor control signal (Phase B) Transfer roller 15 drive motor control signal (Phase /A) Transfer roller 15 drive motor control signal (Phase /B) Toner den misty sensor gain control signal Transfer separation motor control signal Serial I/F data (CCD)

TXD_CCD2

Serial I/F data (CCD)

TXD_FIN

Serial I/F data (Finisher)

TXD_LCC

Serial I/F data (LCC)

TXD_SCN

Serial I/F data (Scanner control PWB) Scanner flash ROM write protect signal Exhaust fan motor control signal (Rear left)

TRMB TRMXA TRMXB TSGOUT TURM

VCCW_SCN VFM-BKL

VFM-BKR

Exhaust fan motor control signal (Rear right)

VFM-EX1

VIDEO VIDEOin-

Exhaust fan motor control signal (LSU top plate front side) Exhaust fan motor control signal (LSU top plate center) Exhaust fan motor control signal (LSU top plate rear side) Image signal Image signal

VIDEOin+

Image signal

VPMA

WEB END

Paper transport motor control signal (Phase A) Paper transport motor control signal (Phase B) Paper transport motor control signal (Phase /A) Paper transport motor control signal (Phase /B) Laser power control signal Reset trigger signal from energy-saving mode WEB END sensor signal

WEBMA

WEB motor control signal

VFM-EX2

VFM-EX3

VPMB VPMXA VPMXB VRB WAKE UP

Function/Operation Machine temperature detection

Connector level “L” “H” — —

Connector No.

Pin No.

PWB name

21

10

PCU

Transfer charger output control (PWM control) Transfer charger ON/OFF control

—

—

15

8

PCU

ON

OFF

15

9

PCU

Waste toner pipe lock detection

—

Lock (Tilt)

8

16

PCU

Toner motor 1 ON/OFF control Toner motor 1 ON/OFF control Toner motor 2 ON/OFF control Toner motor 2 ON/OFF control Waste toner full detection

— — — — —

— — — — —

11 11 11 11 11

1 3 5 7 12

PCU PCU PCU PCU PCU

LCC paper feed timing control (Output from PCU) Transport roller 15 drive motor control Transport roller 15 drive motor control Transport roller 15 drive motor control Transport roller 15 drive motor control Toner density sensor gain control

—

—

18

13

PCU

—

—

10

17

PCU

—

—

10

19

PCU

—

—

10

18

PCU

—

—

10

20

PCU

—

—

12

20

PCU

Stop

7

16

PCU

—

/ Release —

1

63

SCN

—

—

10

14

SCN

—

—

17

11

PCU

—

—

18

3

PCU

—

—

9

8

SCN

Write enable

9

10

SCN

Max. force of wind

Stop

5

22

PCU

Max. force of wind

Stop

6

17

PCU

Max. force of wind

Stop

5

4

PCU

Max. force of wind

Stop

5

10

PCU

Max. force of wind

Stop

5

16

PCU

— —

— —

20 9

21 21

PCU PCU

—

—

9

23

PCU

—

—

10

21

PCU

—

—

10

23

PCU

—

—

10

22

PCU

—

—

10

24

PCU

— Energysave reset —

—

22 9

17 11

PCU SCN

END detection —

24

2

PCU

24

4

PCU

Transfer unit separation control Serial I/F data (Scanner control PWB - CCD) Serial I/F data (Scanner control PWB - CCD) Serial I/F data (PCU PWB - Finisher) aerial I/F data (Controller - Scanner control PWB) Serial I/F data (Controller - Scanner control PWB) Scanner flash ROM write protect Exhaust fan motor control signal (O3 exhaust process section heat exhaust) Exhaust fan motor control signal (Exhaust duplex (ADU) section cooling) Exhaust fan motor control signal (O3 exhaust process section heat exhaust) Exhaust fan motor control signal (O3 exhaust process section heat exhaust) Exhaust fan motor control signal (O3 exhaust process section heat exhaust) Image signal to LSU Image signal from controller to PCU PWB Image signal from controller to PCU PWB Paper vertical transport motor control (Phase A) Paper vertical transport motor control (Phase B) Paper vertical transport motor control (Phase /A) Paper vertical transport motor control (Phase /B) Laser power control Reset trigger from energy saving mode WEB paper end ( Replace) detection Web motor ON/OFF control

—

MX-M700N ELECTRICAL SECTION 11 – 26

Remark

Not used.

Signal name WEBMB WHPR2 XH

XL

YH

Name WEB motor control signal Dehumidifier heater power relay 2 control signal Touch area identification signal (Vertical direction) Touch coordinates signal (Vertical direction)

Web motor ON/OFF control Dehumidifier heater control

Touch area identification signal (Horizontal direction) Touch coordinate signal (Horizontal direction)

YL

Connector level “L” “H” — — Relay ON Relay OFF

Function/Operation

3 4 5 6 7 0

No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

M1SS1

M1SS2

PWB name

24 19

5 18

PCU PCU

—

—

1

96

SCN

Touch coordinates identification (Vertical direction) X axis Touch area identification (Horizontal direction) Y axis

—

—

1

46

SCN

—

—

1

45

SCN

—

—

1

95

SCN

Touch coordinates identification (Horizontal direction) Y axis

M1SS3

Paper size

M1SS4 AB series

M2SS1

M2SS2

M2SS3

M2SS4

L H

L L

H H

L L

H H L L L H

L H H H L H

L L L L L H

L L L H H H

CV_SIZE2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1

CV_SIZE1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1

CV_SIZE0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

CV_SIZE3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Pin No.

Touch area identification (Vertical direction) X axis

Vertical size detection: Connector level Multi-stage tray 1 Multi-stage tray 2 1 2

Connector No.

B5 A4 A5R B5R A4R Foolscap B4 A3

Inch series

China series

Extra K16 LT A4 INVR A5R EX-R K16R LTR A4R Extra Foolscap LGL K8 WLT Tray not installed

Paper size none A3 A4 LT B4 LG WLT INV B5 Extra A5 F4 A4R B5R LTR A5R

MX-M700N ELECTRICAL SECTION 11 – 27

Remark

MX-M700N

[12] OTHERS

5GTXKEG/WCN

1. System settings A. Count specification (1)

Paper exit system counter

Counter

Total counter (Note) Maintenance counter Developer counter All valid paper counter (Note) Copy counter (Copy valid paper) FAX counter Print counter Internet FAX counter Document filing counter Right side paper exit counter Other counter (Self print, etc.)

Count-up timing

When transfer is completed When transfer is completed When transfer is completed When paper exit When paper exit When paper exit When paper exit When paper exit When paper exit When center paper exit When paper exit

Single-side copy Paper feed tray Main unit paper exit Small size Large size 1 2 (1)

Count-up number Duplex copy Paper feed tray ADU ADU Paper feed tray Small size Large size Small size Large size 1 2 (1) 1 2 (1)

Clear

-

1

2 (1)

1

2 (1)

1

2 (1)

Sim24-4

1

2 (1)

1

2 (1)

1

2 (1)

Sim24-5

1 1 1 1 1 1 1 1

2 (1) 2 (1) 2 (1) 2 (1) 2 (1) 2 (1) 2 (1) 2 (1)

-

-

2 2 2 2 2 2 2 2

4 (2) 4 (2) 4 (2) 4 (2) 4 (2) 4 (2) 4 (2) 4 (2)

Sim24-6 Sim24-10 Sim24-9 Sim24-15 Sim24-15 Sim24-9

Large size: A3, 11 x 17. (Greater size than paper length 384mm) * ( ): Count-up number when setting to the large size single count up.

(2)

Document, finishing, paper feed system counter

Counter SPF counter Finish stamp counter Staple counter

Punch counter

Saddle staple counter

Scan total counter ADU counter Inserter counter

Paper feed counter

Manual paper feed tray Paper feed tray 1 Paper feed tray 2 Paper feed tray 3 Paper feed tray 4 LCC

Mode All modes FAX send Internet FAX send All modes (Including inserter stand alone process) All modes (Including inserter stand alone process)

Count event SPF paper feed number Finish stamp use number Staple number

All modes (Including inserter stand alone process) All modes All modes

Saddle staple number

Punch number

Scan number ADU paper feed number

All modes (Including inserter offline process)

Inserter tray paper feed number

All modes

Tray paper feed number

Count-up condition Count is made when starting SPF paper pick. Count is made when stamp is ON.

Clear Sim24-3 Sim24-3

Count is made when bundle exit process is completed. Double count is made when stapling two positions. In the inserter stand alone mode, count is made when process is completed. Count is made when bundle exit process is completed. 1 count regardless of the kind of the punch unit (2-hole, 3-hole, etc.) In the inserter stand alone mode, count is made when process is completed. Count is made when bundle exit process is completed. Only one count is added. In the inserter stand alone mode, count is made when process is completed. Count is made when scan is completed. Count is made when paper feed from the ADU section is started. Count is made when paper feed from the inserter tray is started. In the inserter stand alone mode, count is made when process is completed. Count is made when paper feed from each tray is started.

Sim24-3

Sim24-3

Sim24-3

Sim24-3 Sim24-2 Sim24-3

Sim24-2 Sim24-2 Sim24-2 Sim24-2 Sim24-2 Sim24-2

MX-M700N OTHERS 12 – 1

(3)

Send system counter

Counter Accumulated number of FAX send

Mode G3 FAX send

Count event Number of send

Accumulated page number of FAX send

G3 FAX send

Total page number of send

Accumulated time of FAX send Accumulated page number of scanner scan

G3 FAX send

Send time 4 (Including resending time.) Page number of scan

Scan to E-mail send SHARP DESK send FTP send

Accumulated number of mail send

Scan to E-mail send

Number of mails reached to destination servers

Accumulated number of FTP send

SHARP DESK send FTP send

Number of send reached to destination servers

Accumulated number of internet FAX send

Internet FAX send

Page number of send

Accumulated number of internet FAX receive

Internet FAX send

Page number of scan

Scanner trial counter

Internet FAX send Scan to E-mail send SHARP DESK send FTP send When reading SCAN TO HDD SCAN to SMB send

Page number of scan

Page number of Scan to HDD Accumulated number of SMB send

(4)

HDD storage page number Number of send reached to SMB

Count-up condition Except for the serial transmit operation, one reservation is counted as one communication. For the serial transmit operation, count is made for each communication individually. • Recall is not included. • Polling is counted as a number of send. In the serial transmit operation, each communication is counted as one individually. In bulletin board send, the page number of send is counted.

Clear Sim24-10

Sim24-10

Sim24-10 Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) In case of a send error (excluding document jam) E-mail o Not counted. SHARP DESK/FTP o Counted. Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) Cancel and network error are not counted. Mails transmitted by FTP send are counted in the accumulated number of mail send. Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) Cancel and network error are also counted. Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) The final send result is counted. A send error is counted. Cancel and CE error are not counted. Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) The final send result is counted. A communication error (except for document jam) is counted. Cancel and CE error are not counted. A send (transfer, F code relay broadcast) without document scan is not counted. Count is made for every scan of page. Count is made even when send is not completed. The operation is terminated when the count number exceeds 500.

Sim24-15

Sim24-15

Sim24-15

Sim24-15

Sim24-15

–

Sim24-15 Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) Cancel and network error are also counted.

Sim24-15

Count-up condition The FAX separator sheet is also counted. When polling, the number of received pages is counted. Count by size and count in recovery are the same as the copier specifications. (Counted by the print system.)

Clear Sim24-10

Receive system counter

Counter The accumulated page number of FAX receive print

Mode G3 FAX receive

Count event Total output page number

Accumulated time of FAX receive Accumulated number of internet FAX receive Accumulated page number of internet FAX receive print

G3 FAX receive

Receive time

Internet FAX receive

Receive number

Internet FAX receive

Total receive output number

Sim24-10 A normal mail receive is also counted. Count is made regardless of normal or abnormal. Count is made regardless of print result. Count is made when output is made on a normal mail receive. Print of mail text is not counted. The FAX separator sheet is also counted. Count by size and count in recovery are the same as the copier specifications. (Counted by the print system.)

MX-M700N OTHERS 12 – 2

Sim24-15

Sim24-15

(5)

Department counter Conforming count mode (SIM 26-5)

Data location Operation content

MFP control PWB

FAX

Scanner control PWB

PCU PWB

TOTAL

Copy counter Print counter FAX send page number counter

z z z

■ ■ ■

Network scanner counter

z

—

I-FAX send page number counter

z

■

Document filing counter

z

■

(6)

Mainten ance

—

Count-up condition DV

—

Department FAX send page number • In the serial transmit operation, each communication is counted as one individually. Department network scanner scan page number • i FAX and network scanner • Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is not counted.) Department FAX send page number • In the serial transmit operation, each communication is counted as one individually.

Printer job count-up specification Total use page number counter

Printer job (Without istration) Printer job (With specification) * Printer job (Without specification) * Notice in printer job (Without istration) Notice in printer job (With specification) * Notice in printer job (Without specification) * List print Total use page number print Each department total page number print Engine self print

PRINTS

OTHERS

{ { { { { { — — — —

— — — — — — { { { —

Department counter Driver Key operation specification number number — — — { — — — — — — — — — — — — — — — —

OTHERS — — { — { { — — — —

* When there is "NO" in istration, or when there is not "NO."

(7)

Total counter specifications

The total count viewed from the and the counter used for charging are “Total output counter (total valid paper counter).”

Display when the copy key is ON. List print Valid paper counter to send to serial RIC Total counter to send to serial RIC E-RIC mail text counter E-RIC attached file SIMULATION

Total output Counter ■ ■ ■ ■ ■ ■ (Counter for the first send) Displayed/printed as Total output.

MX-M700N OTHERS 12 – 3

Total Counter — — — — — ■ (Counter to send in the midst of packet) Displayed/printed as Total

(8)

Blank paper count specification

Mode

Print mode

Normal

Without print (Invalid paper exit) Without print (Blank paper insertion) Single face print (Single face mode) Single face print (Duplex mode) Duplex print Without print With print (Single face) With print (Duplex) Without print With print (Single face) With print (Duplex) Without print With print (Single face) With print (Duplex) Without print With print (Single face) With print (Duplex)

Front cover

Back cover

Insert paper

OHP insert paper

Count attribute Print surface Front Back surface surface ✕ —

Blank paper count setting (SIM 26-52) 0: NO 1: YES Small Large Small Large size size size size 0 0 0 0

Remark

U

—

0

0

1

2 (1) *1

{

—

1

2 (1) *1

1

2 (1) *1

SS/DS

{

✕

1

2 (1) *1

1

2 (1) *1

SD (Odd number of documents)

{ U { { ✕ ✕ { U { {

{ — — { U { { — — { — — —

2 0 1 2 0 1 2 0 1 2 0 1 —

4 (2) *1 0 2 (1) *1 4 (2) *1 0 2 (1) *1 4 (2) *1 0 2 (1) *1 4 (2) *1 0 2 (1) *1 —

2 1 1 2 1 1 2 1 1 2 1 1 —

4 (2) *1 2 (1) *1 2 (1) *1 4 (2) *1 2 (1) *1 2 (1) *1 4 (2) *1 2 (1) *1 2 (1) *1 4 (2) *1 2 (1) *1 2 (1) *1 —

SD (Even number of documents)/DD

{ —

Duplex print inhibition

* Large size: A3, 11 x 17. (Greater size than paper length 384mm) *1: Follows SIM 26-5 (Count-up mode). (Default: Double count-up (Set value: 2)) ( ): Large size single count-up setting (Count-up number when set to 1.) {: Counts up. ✕ : Does not count up. U : Follows SIM 26-52 setting.

0 : Does not count up. (Japan/SCA default)

1: Counts up. (Other default)

— : Out of target (No print process)

(9)

Consumables counter specification

Count-up timing

Counter

OPC drum counter OPC drum rotation counter (sec) Developer counter Developing roller rotation counter (sec) Toner counter Toner supply counter (sec)

When transfer is completed When transfer is completed When transfer is completed When transfer is completed When transfer is completed When transfer is completed

Simplex print Paper feed tray – Main unit paper exit Small size Large size 1 2 (1)

Count-up number Duplex print Clear

Paper feed tray – ADU

ADU – Paper feed tray

Small size 1

Large size 2 (1)

Small size 1

Large size 2 (1)

Sim24-7

—

—

—

—

—

—

Sim24-11

1

2 (1)

1

2 (1)

1

2 (1)

Sim24-5

—

—

—

—

—

—

Sim24-11

1

2 (1)

1

2 (1)

1

2 (1)

—

—

—

—

—

—

—

—

(10) Reset and set for suplly counters Work item Setting the toner concentration control level

Simulation SIM 25-2

Reset the OPC drum counter Reset the Developer counter Reset the OPC drum running time counter (sec) Reset the DV running time counter (sec)

SIM 24-7 SIM 24-5 SIM 24-11

Reset item Developer counter DV unit running time counter (sec) OPC drum counter Developer counter OPC drum running time counter (sec)

SIM 24-11

DV unit running time counter (sec)

MX-M700N OTHERS 12 – 4

Included Test Command SIM 24-5 SIM 24-11 — — — —

B. Location and display of each counter data Simulation Code Operation content Main

Sub

22

01

02

08

Each counter display (Total/ Maintenance/Developer/ SPF/ Staple/ Tray) 1 : Total counter 2 : Drum cartridge counter 3 : Toner cartridge counter 4 : Deve cartridge counter 5 : Maintenance counter 6 : Total output page number counter 7 : Copy counter 8 : Printer counter 9 : FAX output counter 10 : I-FAX output counter 11 : Document filing output Counter 12 : Right side output counter

Data size

MFP control PWB

FAX

Scanner control PWB

PCU PWB

z z z z z z

TOTAL

Mainte nance

Count-up condition DV

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

z z z z z z

z

■

Count is made when the main unit paper exit is started. (When POP2 is ON) Refer to the "Count Specifications."

13 : Other print counter Jam/ Trouble counter display 1 : PAPER JAM

z

■

z

—

—

—

2 :

SPF JAM

z

—

—

—

3 :

TROUBLE

z

—

—

—

z

—

—

—

z

—

—

—

z

—

—

—

z

— —

— —

— —

z

—

—

—

One count for every paper pick-up

z

—

—

—

One count for every paper pick-up

z z z

— — —

— — —

— — —

One count for every paper pick-up One count for every paper pick-up One count for every paper pick-up

z

—

—

—

One count for every paper transport start from ADU. One count for every paper pick-up

Document, staple counter display 1 : SPF document feed page number 2 : Scan number 3 :

09

Conforming count mode (Sim26-5)

Data location

Staple number

4 : Punch number 5 : SPF finish stamp number 6 : Saddle staple number 7 : Inserter number Paper feed counter display 1 : Paper feed tray 1 (Tandem Left) 2 : Paper feed tray 2 (Tandem Right) 3 : Paper feed tray 3 4 : Paper feed tray 4 5 : MFT (Manual paper feed tray) 6 : ADU 7 :

LCC

z z z

z

MX-M700N OTHERS 12 – 5

Count is made when an event occurs. (A jam by closing the door during paper transport is not counted.) Count is made when an event occurs. (A jam by closing the door during paper transport is not counted.) Count is made when an event occurs. (Follows the trouble count method of SIM 26-35.) One count is made every time when SPF document is paper feed. One count is made every time when scan is completed. One count for every stapling (Stapling at two positions is counted as 2.) One count for every punching One count for every paper pick-up One count for every paper pick-up One count for every paper pick-up

Simulation Code Operation content Main

Sub

22

11

19

Data size

MFP control PWB

FAX

Scanner control PWB

PCU PWB

Count-up condition

TOTAL

Mainte nance

DV

FAX send/receive counter display 1 : FAX send (Send counter)

32bit

z

—

—

—

2 :

FAX receive (Receive counter)

32bit

z

—

—

—

3 :

FAX output (FAX print counter)

32bit

z

■

4 :

FAX send images (Send page number)

32bit

z

—

—

—

Send time (Send time) 6 : Receive time (Receive time) Process section count data display 1 : Drum counter

48bit

—

—

—

—

—

—

5 :

13

Conforming count mode (Sim26-5)

Data location

48bit

z

■

z

2 : 3 :

Drum rotating time Toner counter

z z

—

—

— ■

4 : 5 :

Toner supply time Developer counter

z z

—

—

— ■

z

—

—

—

—

—

—

6 : Developer rotating time Display of counters related to the network scanner 1 : Network scanner document scan page number counter

32bit

z

MX-M700N OTHERS 12 – 6

Accumulated page number of send • Except for the serial transmit operation, one reservation is counted as one communication. • For the serial transmit operation, count is made for each communication individually. • Recall is not included. • Saved in the FAX-SRAM. Accumulated number • Count is made regardless of normal or abnormal completion. • Saved in the 32bit counter and the FAX-SRAM. The accumulated page number of FAX receive print Count by size and count in recovery are the same as the copier specifications. • Counted by the print system. Refer to the “Count Specifications.” Accumulated page number of send • In the serial transmit operation, each communication is counted as one individually. • Saved in the 32bit counter and the FAX-SRAM. hhhhhhhh:mm:ss Saved in the FAX-SRAM. hhhhhhhh:mm:ss Saved in the FAX-SRAM. Refer to the “Count Specifications.” (Same as the developer counter.) Count for every second of rotation Refer to the “Count Specifications.” (Same as the developer counter.) Count for every second of rotation Refer to the “Count Specifications.” (Same as the developer counter.) Count for every second of rotation

Accumulated page number of scanner scan • The page number of normal completion of i FAX, E-mail, and FTP (DESK) send. • In sequential broadcast, count is made when one destination send is normally completed. • In case of a communication error: (Except for document jam) For i FAX and E-mail, send is canceled and no page is sent. Therefore count is not made. For FTP (DESK), though send is canceled, data reached in the server remains, and only the page number of send is counted. • Saved in the FAX-SRAM.

Simulation Code Operation content Main

Sub

22

19

Conforming count mode (Sim26-5)

Data location Data size

MFP control PWB

FAX

Scanner control PWB

PCU PWB

Count-up condition

TOTAL

Mainte nance

DV

2

Mail send counter

32bit

z

—

—

—

3

FTP send counter

32bit

z

—

—

—

4

I-FAX original (Scan page number counter)

32bit

z

—

—

—

5

I-FAX send (Send counter)

32bit

z

—

—

—

6

I-FAX receive (Receive counter)

32bit

z

■

—

—

7

I-FAX output (Print page number counter)

32bit

z

—

—

—

8

SCAN TO HDD (Save page number counter)

32bit

z

—

—

—

MX-M700N OTHERS 12 – 7

Accumulated number of mail send • The number of send mails of i FAX, E-mail, and FTP is counted. • Even in the serial system, one scan is counted. (The number of receivers is not counted.) • The number of mails reached to the server is counted. • Since server data are deleted in case of send cancel or a network error, count is not made. • Saved in the FAX-SRAM. Accumulated number of FTP send • The page number of FTP (DESK) send is counted. • Even in the serial transmit operation, the page number of one scan is counted. (The number of receivers is notcounted.) • The number of mails reached to the server is counted. • In case of send cancel or a network error, the server data cannot be deleted. Therefore, count is made. • Saved in the FAX-SRAM. Accumulated page number of internet FAX scan • A communication error (except for document jam) is counted. • Cancel and CE error are not counted. • A send (Transfer, F code relay broadcast) without document scan is not counted. • Saved in the FAX-SRAM. Accumulated number of internet FAX send • A send error is counted. • Resend is not counted. • Cancel and CE error are not counted. • Saved in the 32bit counter and the FAX-SRAM. Accumulated number of internet FAX send • A normal mail receive is also counted. • Saved in the 32bit counter and the FAX-SRAM. Accumulated page number of internet FAX receive print Count by size and count in reprint after a jam are the same as the copier specifications. Page number of SCAN TO HDD save • The page number of documents saved to HDD is counted.

2. Web setting service mode

(Check or delete of ed font) 1)

Press "xxx.xxx.xxx.xxx (IP address)/font_down.html" and press ENTER key.

The Web setting service mode provides the following functions:

2)

Enter the name and the , and press OK button.

• Font / Form

3)

Select Management menu.

A. Outline

• Device Cloning These functions are used to backup the data and the key operatorprogram setting data, and to import backup data to another machine. By using these functions, two or more machines can be set in the same conditions in a short time. • i-Fax Setup This function is used to backup i-Fax receive data to the FTP server. By using this function, receive data are backed up to the FTP server when they cannot be printed by some reasons (paper empty, toner empty, paper jam, etc.) and can be printed out after recovery of the machine. After completion of printing the backup data, they are deleted from the FTP server. • Setup Recheck and input the and press [Submit] button.

B. Operating procedures Entering the Web setting mode 1)

Boot the browser software.

2)

Enter “xxx.xxx.xxx.xxx (IP address)/xxxx_xxxxx.html” and press ENTER key.

3)

Enter the name and the , and press OK button.

(NOTE): The default name and the default are as follows: name: service

: shArp

* The can be optionally changed in the following procedures:

The list of ed fonts and the used percentage of the font area in the memory device are displayed. Press “Initialize” button and press Yes key, and the ed fonts will be deleted.

1)

Enter "xxx.xxx.xxx.xxx(IP address)/_setting.html" and press ENTER key.

(2)

2)

Enter a new .

(Backup)

3)

Enter the new again in the check column.

1)

4)

Press SUBMIT button.

Press “xxx.xxx.xxx.xxx (IP address)/device_cloning.html” and press ENTER key.

2)

Enter the name and the , and press OK button.

3)

Select an item to be backed up. (Application / Key operator setting)

4)

Press Execute key.

5)

Press Save button. (File mode)

C. Description (1)

Device Cloning

Font/Form

(Font ) 1)

Press "xxx.xxx.xxx.xxx (IP address)/font_down.html" and press ENTER key.

2)

Enter the name and the , and press OK button.

3)

Select "" menu.

4)

Select Resourced type.

5)

Select Storage Device.

6)

Select Font file.

7)

Press "" button.

6)

Select the destination of save.

7)

Press Save button.

MX-M700N OTHERS 12 – 8

(Import) 1)

Press “xxx.xxx.xxx.xxx (IP address)/device_cloning.html” and press ENTER key.

2)

Enter the name and the , and press OK button.

3)

Select the backed up file (xxxx.bin).

4)

Press Execute key. The backed up data (setup data) are written into the machine.

(3)

I-Fax Setup

1)

Press "xxx.xxx.xxx.xxx (IP address)/i-FAX_ftp.html" and press ENTER key.

2)

Enter the name and the , and press OK button.

3)

Enter the FTP server address to which i-Fax receive data are backed up.

4)

Enter the directory.

5)

Enter the name

6)

Enter the .

7)

Press SUBMIT button.

(4) 1)

Setup Page of the change for the serviceman. Pas s word S etup Page - Mic ros oft Internet E xplorer

Service

Counts regardless of normal or abnormal. (/ setting htmll)

MX-M700N OTHERS 12 – 9

3. Paper JAM code A. Paper jam judgment conditions JAM detection method JAM code

TRAY1 PFD2_NM1

Content

Tray 1 paper feed jam (PFD2 not-reached) PFD2 not-reached jam (Tray 3 feed paper)

PFD2_NM2

PFD2 not-reached jam (Tray 4 feed paper)

PFD2_NAD

PFD2 not-reached jam (ADU re-feed paper) PPD1 not-reached jam (Manual feed tray feed paper) PPD1 not-reached jam (Tray 1 feed paper) PPD1 not-reached jam (Tray 2 feed paper) PPD1 not-reached jam (Tray 3 feed paper) PPD1 not-reached jam (Tray 4 feed paper) PPD1 not-reached jam (LCC paper feed paper) PPD1 not-reached jam (ADU re-feed paper) POD1 not-reached jam POD2 not-reached jam ADU paper entry sensor notreached jam

PPD_NMF PPD_NT1 PPD_NT2 PPD_NM1 PPD_NM2 PPD_NLC PPD_NAD POD1_N POD2_N AINPD_N (Saddle)

AINPD_N (Other)

ADU paper entry sensor notreached jam

APPD1_N

ADU transport sensor 1 notreached jam ADU transport sensor 2 notreached jam Tray 3 paper feed jam (M1PFD not-reached) Tray 4 paper feed jam (M2PFD not-reached) M1PFD not-reached jam (Tray 4 feed paper) MPRD2 not-reached jam (Tray 2 feed paper)

APPD2_N DESK1 DESK2 M1PFD_N2 MPRD2_N2

MPRD2_NM

MPRD2_NL

TRAY2 MPRD1_NM

MPRD1_NL MPFD2_NM

MPFD2_NL BPT LPPD_N

MPRD2 not reached jam (Manual paper feed tray feed paper) MPRD2 not-reached jam (LCC paper feed paper) Tray 2 paper feed jam (MPRD1 not-reached) MPRD1 not-reached jam (Manual paper feed tray feed paper) MPRD1 not-reached jam (LCC paper feed paper) MPFD2 not-reached jam (Manual paper feed tray feed paper) MPFD2 not-reached jam (LCC paper feed paper) Manual tray feed jam (MPFD1 not-reached) LPPD not-reached jam

JAM detection timer start trigger (JAMTST)

JAM judge dedtector (JAMJD)

JAM judge time (JAMTST - JAMJD) 55/62 PPM 70 PPM MODEL MODEL (335mm/s) (395mm/s) 1608ms 1516ms

T1PFC ON

PFD2 ON

VPM ON (When the paper lead edge comes to 40mm in front of the transport roller 13, VPM turns ON.) VPM ON (When the paper lead edge comes to 40mm in front of the transport roller 13, VPM turns ON.) APPD2 ON

PFD2_NM1

541ms

480ms

PFD2_NM2

541ms

480ms

PFD2_NAD

819ms

710ms

MPRD2 ON

PPD ON

429ms

364ms

PFD2 ON

PPD ON

352ms

298ms

MPRD2 ON

PPD ON

429ms

364ms

PFD2 ON

PPD ON

352ms

298ms

PFD2 ON

PPD ON

352ms

298ms

MPRD2 ON

PPD ON

429ms

364ms

PFD2 ON

PPD ON

352ms

298ms

RRC ON POD1 ON DGS ON (When the paper lead edge is transported to 30mm apart from the switchback operation startposition.) DGS ON (When the paper lead edge is transported to 30mm apart from the switchback operation startposition.) AINPD ON

POD1 ON POD2 ON AINPD_ON (Saddle)

943ms 429ms 435ms

800ms 364ms 435ms

AINPD_ON (Other)

318ms

318ms

APPD1ON

292ms

292ms

APPD1 ON + 90mm

APPD2 ON

375ms

375ms

M1PFC ON

M1PFD ON

1531ms

1450ms

M2PFC ON

M2PFD ON

1531ms

1450ms

M2PFD ON

M1PFD ON

513ms

435ms

VPM ON (When the paper lead edge comes to 40mm in front of the transport roller 4, VPM turns ON.) VPM ON (When the paper lead edge comes to 40mm in front of the transport roller 4, VPM turns ON.) VPM ON (When the paper lead edge comes to 40mm in front of the transport roller 4, VPM turns ON.) T2PFC ON

MPRD2 ON

467ms

417ms

MPRD2 ON

467ms

417ms

MPRD2 ON

467ms

417ms

MPRD1 ON

1519ms

1440ms

MPFD2 ON

MPRD1 ON

564ms

478ms

MPFD2 ON

MPRD1 ON

564ms

478ms

MPFD1 ON

MPFD2 ON

570ms

483ms

LPPD ON

MPFD2 ON

677ms

574ms

MPFC ON

MPFD1 ON

1367ms

1311ms

LTD ON (LCC)

LPPD ON

1447ms

1379ms

MX-M700N OTHERS 12 – 10

JAM detection method JAM code

Content

JAM detection timer start trigger (JAMTST)

JAM judge dedtector (JAMJD)

PFD2_ST1

PFD2 remaining jam (Tray 1 feed paper)

RRC ON

PFD2 OFF (PFD2 paper rear edge detection) + 65mm

PFD2_SM1

PFD2 remaining jam (Tray 3 feed paper)

PFD2 OFF

PFD2_SM2

PFD2 remaining jam (Tray 4 feed paper)

PFD2_SAD

PFD2 remaining jam (ADU re-feed paper)

M1PFD OFF (When paper is transported by 50mm from M1PFD paper rear edge detection.) M1PFD OFF (When paper is transported by 50mm from M1PFD paper rear edge detection.) RRC ON

PPD_ST1

PPD1 remaining jam (Tray 1 feed paper) PPD1 remaining jam (Tray 2 feed paper) PPD1 remaining jam (Tray 3 feed paper) PPD1 remaining jam (Tray 4 feed paper) PPD1 remaining jam (LCC paper feed paper) PPD1 remaining jam (ADU re-feed paper) PPD1 remaining jam (Manual feed tray feed paper) POD2 not-reached jam

PFD2 OFF

PPD_ST2 PPD_SM1 PPD_SM2 PPD_SLC PPD_SAD PPD_SMF POD1_S (Right paper exit, infinite form) POD1_S (Left paper exit) POD2_SR

POD2_SL

AINPD_S (Saddle paper exit) AINPD_S (Other) APPD1_S APPD2_S

M1PFD_S1 M1PFD_S2 M2PFD_S MPRD2_S2 MPRD2_SM

MPRD2_SL MPRD1_S2 MPRD1_SM

MPRD1_SL MPFD2_SM

671ms

569ms

PPD OFF

PFD2 OFF (PFD2 paper rear edge detection) + 65mm 352ms

298ms

MPRD2 OFF

PPD OFF

429ms

364ms

PFD2 OFF

PPD OFF

352ms

298ms

PFD2 OFF

PPD OFF

352ms

298ms

MPRD2 OFF

PPD OFF

429ms

364ms

PFD2 OFF

PPD OFF

352ms

298ms

MPRD2 OFF

PPD OFF

429ms

364ms

PPD OFF

POD1 OFF

1128ms

956ms

POD2 not-reached jam

PPD OFF

POD1 OFF

1128ms

956ms

POD2 remaining jam (When paper is discharged on the right side of the machine.) POD2 remaining jam (When paper is discharged on the left side of the machine.) ADU paper entry sensor remaining jam ADU paper entry sensor remaining jam ADU transport sensor 1 remaining jam ADU transport sensor 2 remaining jam

POD1 OFF

POD2 OFF

429ms

364ms

POM1 ON (Switchback start)

POD2 OFF

POD2 OFF

AINPD OFF

187ms

187ms

POD2 OFF

AINPD OFF

187ms

187ms

AINPD OFF

APPD1 OFF

292ms

292ms

LD ON

APPD2 OFF (APPD2 paper rear edge detection) + 65mm

M1PFD remaining jam (Tray 3 feed paper) M1PFD remaining jam (Tray 4 feed paper) M2PFD remaining jam

M1PFD ON

M1PFD OFF

M2PFD OFF

M1PFD OFF

APPD2 OFF (APPD2 paper rear edge detection) + 65mm Paper length + 65mm 513ms

435ms

M2PFD ON

M2PFD OFF

MPRD1 OFF

MPRD2 OFF

Paper length + 65mm 653ms

554ms

MPRD1 OFF

MPRD2 OFF

653ms

554ms

MPRD1 OFF

MPRD2 OFF

653ms

554ms

MPRD1 ON

MPRD1 OFF

MPFD2 OFF

MPRD1 OFF

Paper length + 65mm 564ms

478ms

MPFD2 OFF

MPRD1 OFF

564ms

478ms

MPFD1 OFF

MPFD2 OFF

570ms

483ms

MPRD2 remaining jam (Tray 2 feed paper) MPRD2 remaining jam (Manual paper feed tray feed paper) MPRD2 remaining jam (LCC paper feed paper) MPRD1 remaining jam (Tray 2 feed paper) MPRD1 remaining jam (Manual paper feed tray feed paper) MPRD1 remaining jam (LCC paper feed paper) MPFD2 remaining jam (Manual paper feed tray feed paper)

PFD2 OFF

JAM judge time (JAMTST - JAMJD) 55/62 PPM 70 PPM MODEL MODEL (335mm/s) (395mm/s) PFD2 OFF (PFD2 paper rear edge detection) + 65mm 671ms 569ms

PFD2 OFF (PFD2 paper rear edge detection) + 65mm

MX-M700N OTHERS 12 – 11

Paper length + 115mm

JAM judge time (JAMTST - JAMJD) 55/62 PPM 70 PPM MODEL MODEL (335mm/s) (395mm/s) 1447ms 1379ms

JAM detection method JAM code

MPFD2_SL

Content

JAM detection timer start trigger (JAMTST)

MPFD1_S

MPFD2 remaining jam (LCC paper feed paper) MPFD1 remaining jam

LPPD_S

LPPD remaining jam

PPD_PRI

PPD1 jam (Image ready request is not sent from ICU.)

LPPD_LCC

LPPD jam (No reply in a certain time after preliminary paper feed from LCC and issuing the paper feed command.)

JAM judge dedtector (JAMJD)

LPPD OFF

MPFD2 OFF

MPFD1 ON

MPFD1 OFF

LTD OFF (LCC paper feed complete) Image data send ready request command is sent. (PCU to MFP CONTROL) Preliminary paper feed request command is sent. (PCU to LCC)

LPPD ON Image data send ready status is sent. (MFP CONTROL to PCU) Preliminary paper feed start status is sent. (LCC to PCU)

Paper length + 65mm 1447ms

1379ms

30000ms

30000ms

70sec

70sec

[Sensor (cross-section)]

sensor cross section

SPED1 SPUD SPLS2

SPPD1

SPLS1

SPWS SPPD3 SPPD4

SPED2

SPOD

TH_SEN

SPPD2

T_SEN TS_SEN REG_SEN T_VR

EMP_SEN

BUFENTR

TIM_SEN

POD3

PDEL

POD2

BUF FSTTRAY

PENT

STPTY

HI_SEN H_SEN

AINPD

POD1

APPD1 1STPA 2NDPA

SNDTRAY

MPED MPED

3RDPA

MPLD1

MPFD1 MPFPWS

PPD APPD2

MPRD2

MPRD1

MTOP1 MTOP2

MPFD2 LPPD

PFD2

T2S PWB LTD

VPJM

T1S PWB

T1PPD

PAFLDHP LUNGEHP LUNGETOP

DELV FDRLHP GIDHP

M1PFD

M1LUD M1PED

M2PFD

M2LUD M2PED

TRYPAR PPOSPAR PAPPOS

MX-M700N OTHERS 12 – 12

LPED

MPLD2

[Clutch/Solenoid (cross-section)] clutch/solenoid cross section

SPFC

STRRBC STRRC

STRBC STRC STRRBC STRRC

R_CL EXITSL

PDLSL

EXTSL

FLPSL

BESSL

F_SOL

DGS

ESSL

PSPS FLPSL1 MFPUS RRC MPFC FLPSL2 LPSL T2PFC T1PFC

RLNIPSL

MPFGS

LTCL

HPFC LPFCL

T2PUS T1PUS DSKPFC2

M1PUS

DSKPFC1

M1PFC M2PUS M2PFC

[Motor (cross-section)]

motor cross section

SLUMB

SPFM

SPSM K_MOT M1 MIM M1P

M7 M8

POM2

Y_MOT

M5

1

M2 M3

M9

M2P

M6

WEBM

POM1 FUM

H_MOT M4

DM

M10

TM1X TM2X MM M6S M7S

DVM

TRM MM

VPM 2

LTM

M1S M8S M2S MM T2LUM

T1LUM

M5S M3S M4S M1LUM

M2LUM

MX-M700N OTHERS 12 – 13

LLM

B. Inserter (AR-CF2) paper jam judgment conditions JAM code

Name

REG_SEN_N

Resist sensor not-reached JAM

REG_SEN_S

Resist sensor remaining JAM

TIM_SEN_N

JAM detection method JAM detection start trigger JAM judge detector Separation start Resist sensor ON Resist sensor OFF

Timing sensor not-reached JAM

Transport start from the take-up position (*1) Resist sensor ON

TIM_SEN_S

Timing sensor remaining JAM

Resist sensor OFF

Timing sensor OFF

HI_SEN_NI

Paper exit sensor remaining JAM (Inserter paper feed) Paper exit sensor notreached JAM (Main unit paper feed) Paper exit sensor remaining JAM (Main unit paper feed) Paper exit sensor remaining JAM (Inserter paper feed) Reverse sensor notreached JAM (When entering the reverse path) Reverse sensor notreached JAM (When exiting from the reverse path) Reverse sensor remaining JAM (When entering the reverse path) Reverse sensor remaining JAM (When exiting from the reverse path)

Timing sensor ON

Reverse sensor ON

Main unit paper exit command receive After ing by 20mm from the paper exit sensor ON Timing sensor OFF

Reverse sensor ON

Paper exit sensor OFF

Timing sensor ON

Reverse sensor ON

Switchback start

Reverse sensor ON

Timing sensor OFF

Reverse sensor OFF

After ing 20mm from the reverse sensor ON

Reverse sensor OFF

HI_SEN_NP HI_SEN_S

H_SEN_NIN H_SEN_NOUT H_SEN_SIN H_SEN_SOUT

Timing sensor ON

Paper exit sensor OFF

JAM judge distance (Distance from pick descending start to resist sensor ON) ✕ 5 Max. document length (WLT) - (Resist sensor OFF to take-up position) + 200mm Distance from resist sensor ON to timing sensor ON + 200mm Distance from resist sensor OFF to timing sensor OFF + 200mm Distance from timing sensor ON to paper exit sensor ON + 200mm Distance from main unit side to paper exit sensor ON + 500mm Max. document length (WLT) + 200mm Distance from timing sensor OFF to paper exit sensor OFF + 200mm Distance from timing sensor ON to reverse sensor ON + 100mm Distance from reverse stop position (*2) to reverse sensor ON + 100mm Distance from timing sensor OFF to reverse sensor OFF + 100mm Max. Document length (WLT) + 100mm

*1) The take-up position is 30mm downstream from the vertical path transport roller. *2) The reverse stop position is 20mm downstream from the reverse sensor.

JAM detection method JAM code

Content JAM detection timer start trigger

FES_N

FINISHER entry port remaining JAM

FES_S

FINISHER entry port remaining JAM

FFPS_N

FFPS_S

FEXIT_S FSTPL

Main unit paper exit command receive Entry port sensor ON

FINISHER buffer sensor notreached JAM FINISHER buffer sensor remaining JAM FINISHER paper exit sensor notreached JAM FINISHER paper exit sensor remaining JAM FINISHER saddle transport path sensor remaining JAM

Entry port sensor ON

FINISHER saddle transport path sensor remaining JAM

Saddle transport path sensor ON

FINISHER saddle paper exit sensor not-reached JAM FINISHER saddle paper exit sensor remaining JAM

Folding edge sensor ON (Completion of thrust operation) Saddle paper exit sensor ON

FINISHER bundle exit remaining JAM FINISHER Stacker staple JAM

Start of bundle exit to the stack tray Start of stacker stapling

Buffer sensor ON Entry port sensor ON Entry port sensor ON Entry port sensor ON

JAM judge detector

The paper entry sensor is not turned ON within the specified time. The paper entry sensor is not turned OFF within the specified time. The buffer sensor is not turned ONwithin the specified time. The buffer sensor is not turned OFF within the specified time. The paper exit sensor is not turned ON within the specified time. The paper exit sensor is not turned OFF within the specified time. The saddle transport path sensor is not turned ON within the specified time. The saddle transport path sensor is not turned OFF within the specified time. The saddle transport sensor is not turned ON though paper is transported in the specified distance. The saddle paper exit sensor is not turned OFF though paper is transported in the specified distance. The staple tray sensor is not turned OFF within the specified time. When the staple HP sensor does not sense ON within the specified time from staple HP sensor OFF in stapling process, and when the staple HP sensor detects ON in reverse rotation after stopping the stapler.

MX-M700N OTHERS 12 – 14

JAM judgment time (Stacker: LTR horizontal size Saddle: LTR vertical size) Common to 55/62, 70PPM MODELS (Main unit paper exit speed: Stacker: 800mm/s Saddle: 420mm/s) 500ms 540ms 688ms 540ms Straight path transport: 453ms Buffer path transport: 815ms 840ms 914ms

996ms

180mm (Twice as much as the normal distance) 209.25mm (1.5 times as much as the normal distance) 1000ms 500ms

JAM detection method JAM code

Content JAM detection timer start trigger

FSTPL

FINISHER saddle staple JAM

Start of saddle stapling

FPNCH

FINISHER punch JAM

FDOP

FINISHER door open JAM

Punch HP OFF after starting punching One of finisher doors open

JAM judge detector

When the staple HP sensor does not sense ON within the specified time from stapler HP sensor OFF in stapling process, and when the staple HP sensor detects ON in reverse rotation after stopping the stapler. The punch HP sensor does not turn ON within the specified time. Finisher door open is detected in finishing process.

MX-M700N OTHERS 12 – 15

JAM judgment time (Stacker: LTR horizontal size Saddle: LTR vertical size) Common to 55/62, 70PPM MODELS (Main unit paper exit speed: Stacker: 800mm/s Saddle: 420mm/s) 500ms

200ms ---



[A] EXTERNAL OUTFIT

MX-M700N

5GTXKEG/WCN

Disassembly of each external outfit part refer to each section. No. (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13)

Parts Front cabinet Rear cabinet upper Rear cabinet Right side cabinet upper Right side cabinet lower Top left cabinet Left lower cabinet Right cabinet center Front cabinet upper Paper exit tray cabinet Left cabinet upper Right cabinet upper Left front cabinet

(6) (1) (9) (11)

(7)

(4)

(13)

(2)

(10) (5) (8) (3) (12)

MX-M700N EXTERNAL OUTFIT A – 1



[B] OPERATION

MX-M700N

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

ORSLED EHR-3 OCSW 3 GND 2 5V1 1

TOUCH OCSW

LCD

/ORSPD

1

/CCFT

2

3

1 2 3 4 5 6 7 8 9 10 11 12 13

/YL XH YH /XL

CN2 53259-0417 1 CCFT+ 2 NC 3 NC 4 /CCFT

4 3 2 1

CN1 S3B-PH-K-S(LF) /CCFT 3 2 GND +24V 1

INV PWB

S6B-PH-K-S PDSEL0 1 PDSEL1 2 PDSEL2 3 4 5V2 5 PD 6 GND

CN2 52271-1379 DISP YD LP +3.3V GND M D0 D1 D2 D3 +24V VEE

CN4 52271-0469 1 /YL 2 XH 3 YH 4 /XL

LVDS PWB

CN3 S3B-PH-SM4-TB(LF) 1 /CCFT 2 GND 3 +24V

1 2 3 4 5 6

CN2 B6B-PH-SM4-TB(LF)(SN) PDSEL0 PDSEL1 PDSEL2 5V2 PD GND

MFP OPE PWB

Code

Signal name

Name

CN1 52271-3079 30 XH 29 /YL 28 /XL 27 YH 26 /CCFT 25 24V3 24 GND 23 TH 22 GND 21 lcdD320 lcdD3+ 19 lcdD218 lcdD2+ 17 lcdD116 lcdD1+ 15 lcdD014 lcdD0+ VCONT 13 12 3.3V3 LCD_DISP 11 10 GND LCD_- 9 LCD_+ 8 7 GND LCD_LP- 6 LCD_LP+ 5 4 lcdM3 lcdM+ LCD_YD- 2 LCD_YD+ 1

CN1 52610-2471 1 GND 2 5V1 3 /BZR 4 NC 5 NC 6 GND 7 GND 8 GND 9 /F3 10 /F2 11 /F1 12 /F0 13 SEG2 14 SEG1 15 SEG0 /KEYIN 16 17 5V2 18 GND 19 PD 20 5V2 PDSEL2 21 PDSEL1 22 PDSEL0 23 24 GND

FFC-30Pin

FFC-24Pin

CN6 30FMZ-BT 1 XH 2 /YL 3 /XL 4 YH 5 /CCFT 6 24V3 7 GND 8 TH 9 GND 10 lcdD311 lcdD3+ 12 lcdD213 lcdD2+ 14 lcdD115 lcdD1+ 16 lcdD017 lcdD0+ 18 LCD-VEE 19 3.3V3 20 lcdDIS 21 GND 22 lcd223 lcd2+ 24 GND 25 lcd126 lcd1+ 27 lcdM28 lcdM+ 29 lcdS30 lcdS+

Function/Operation

LCD unit Touch

ORSLED

Trigger for document size detection. Backlight for LCD.

OCSW

OCSW

Document size detection light emitting PWB Document size detection light reception PWB SPF open/close detector

/CCFT

/CCFT

LCD backlight

No. 1 2 3

Name LVDS PWB Operation control PWB INV PWB

SCN JNT PWB

CN5 T24FAZ-SMT-TF 24 GND 23 5V1 22 /BZR 21 NC 20 NC 19 GND 18 GND 17 GND 16 /F3 15 /F2 14 /F1 13 /F0 12 SEG2 11 SEG1 10 SEG0 9 /KEYIN 8 5V2 7 GND 6 PD 5 5V2 4 PDSEL2 3 PDSEL1 2 PDSEL0 1 GND

LCD TOUCH

ORSPD

CN4 TX25-100P-LT-H1 1 GND 2 GND /1 DBL- 3 /1 DBL+ 4 5 1 CLK1 CLK+ 6 1 DATA0- 7 1 DATA0+ 8 1 DATA1- 9 1 DATA1+ 10 1 DATA2- 11 1 DATA2+ 12 1 DATA3- 13 1 DATA3+ 14 15 GND 16 GND /CCDFAN 17 18 12V2 19 24V3 20 24V3 PDSEL1 21 PDSEL2 22 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdMlcd1+ 31 lcd1- 32 lcd2+ 33 lcd2- 34 35 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL /STSET 47 /STMPS 48 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 FRM CCD1 61 CLK CCD1 62 TXD CCD1 63 RES CCD1 64 RXD CCD1 65 ADD CCD1 66 GND 67 PAGE1 68 GND 69 GND 70 /CL1 71 PDSEL0 72 5V2 73 PD 74 SEG1 75 SEG2 76 GND 77 /F0 78 GND 79 /F1 80 GND 81 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 5V1 88 lcdDIS 89 3.3V3 90 GND 91 LCD VEE 92 TH 93 /CCFT 94 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND

CN1 TX24-100R-LT-H1 1 GND 2 GND 3 / 1 DBL4 / 1 DBL+ 5 1 CLK6 1 CLK+ 7 1 DATA08 1 DATA0+ 9 1 DATA110 1 DATA1+ 11 1 DATA212 1 DATA2+ 13 1 DATA314 1 DATA3+ 15 GND 16 GND 17 /CCDFAN 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 61 FRM CCD1 62 CLK CCD1 63 TXD CCD1 64 RES CCD1 65 RXD CCD1 66 ADD CCD1 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 81 GND 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 88 5V1 89 lcdDIS 90 3.3V3 91 GND 92 LCD VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND

CN3 B6B-PH-K-S 5V1 1 GND 2 OCSW 3 24V3 4 /LED0 5 /LED1 6

SCN cnt PWB

Type

NOTE

Displays the various menu and information. Executes the various adjustments and the setting operation. Generates the document size detection signal. Generates the document size detection signal.

Function/Operation Generates the LCD display signal. Controls the display operation . Generates a high voltage for backlight.

MX-M700N OPERATION B – 1

Transmission type Cold Cathode Fluorescent Tube

Sensor

2. Operational descriptions

3)

Disconnect each cables.

4)

Remove the earth terminal.

5)

Disconnect the cable while saving an operation unit.

A. Outline This section describes various types of settings, display and operation. The LCD display section is controlled by the MFP CONTROL PWB. The touch , operation keys and LED display are controlled by the SCANNER CONTROL PWB.

3. Disassembly and assembly A. Operation No. (1)

Unit Operation unit

No. a b c d e

(1)-e

Parts Operation control PWB LVDS PWB LCD INV-J PWB LCD unit Touch

(1) (1)-a

(1)-b (1)-c (1)-d

(1) 1)

Operation unit Remove the screws. Remove the upper right cabinet.

3

a. Operation control PWB 2)

Remove the cover of the operation section.

1)

Remove the operation unit. (See "(1) Operation unit")

2)

Remove the earth terminal.

3)

Remove the operation control PWB.

MX-M700N OPERATION B – 2

b. LVDS PWB 1)

Remove the operation unit. (See "(1) Operation unit")

2)

Disconnect each cables.

3)

Remove the LVDS PWB.

4)

Remove the LCD unit.

e. Touch 1)

Remove the operation unit. (See "(1) Operation unit")

Remove the operation unit. (See "(1) Operation unit")

2)

Disconnect the flat cable.

Disconnect each cables.

3)

Remove the earth wire.

Remove the LCD INV-J PWB.

4)

Remove the LCD unit.

5)

Remove the touch .

c. LCD INV-J PWB 1) 2) 3)

d. LCD unit 1)

Remove the operation unit. (See "(1) Operation unit")

2)

Disconnect each cables.

3)

Remove the LCD cover.

MX-M700N OPERATION B – 3

Service Manual MX-M700N

[C] DSPF SECTION 1. Electrical and mechanism relation diagram A. The paper feed tray section

SPLS2 SPLS1

/SLUMB SPWS

SPED2

SPWS STLD

SMP-05V-NC 1 2 3 4 5 SMR-12V-N 1 2 3 4 5 6 7 8 9 10 11 12

B3B-PH-K-S 5V1 3 SPED2 2 1 GND

5V2 STLD GND

B3B-PH-K-S 3 2 1

PHNR-3-H +BU3P-TR-P-H 1 2 3

OUT /SLUMB OUT /SLUMA OUT SLUMB OUT SLUMA 24V3

SCNcnt PWB

SMR-05V-N 1 2 3 4 5

DSPF PWB

SMP-12V-NC

5V2 SPPD4 GND 5V2 SPPD3 GND 5V1 SPED2 GND 5V2 STLD GND

1 2 3 4 5 6 7 8 9 10 11 12

CN3 B34B-PHDSS-B 1 OUT /SLUMB 2 /STRC 3 OUT /SLUMA 4 /STRBC 5 OUT SLUMB 6 /SRRBC 7 OUT SLUMA 8 /SRRC 9 GND 10 GND 11 GND 12 GND 13 GND 14 GND 15 GND 16 GND 17 5VPOD 18 GND 19 5V2 20 GND 21 5V2 22 5V2 23 5V2 24 5V2 25 VAREF 26 N.C 27 24V3 SRRBC 28 5V2 29 24V3 FAN 30 24V3 STRBC 31 24V3 STRC 32 24V3 SRRC 33 24V3 PM 34 N.C

PHNR-3-H

VAREF SPWS GND

3 2 1

B3B-PH-K-S 5V2 SPLS2 GND

3 2 1

B3B-PH-K-S 5V2 3 SPLS1 2 GND 1

PHNR-9-H +BU9P-TR-P-H 1 VAREF 2 SPWS 3 GND 4 5V2 5 SPLS2 6 GND 7 5V2 8 SPLS1 9 GND

PHNR-9-H 9 8 7 6 5 4 3 2 1

5V2

CN2 B32B-PHDSS-B GND GND VAREF N.C 24V3 SPPD2 24V3 SCOV 5V2 SPPD1 /SPFMA SPED1 SPFMA STUD /SPFMB SPFMO1 SPFMB SPFMO2 STRRC STRRBC /SLUMA /SLUMB SLUMA SLUMB SPF SET SRRBC SRRC STRC STRBC SPFC GND GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

CN12 S22B-PHDSS-B 1 GND 2 GND 3 VAREF 4 5V1 5 24V3 6 SPPD2 7 24V3 8 SCOV 9 5V2 10 SPPD1 11 /SPFMA 12 SPED1 13 SPFMA 14 STUD 15 /SPFMB 16 SPFMO1 17 SPFMB 18 SPFMO2 19 STRRC 20 STRRBC 21 GND 22 GND

CN11 S20B-PHDSS-B /SLUMA 1 /SLUMB 2 SLUMA 3 SLUMB 4 5 SPF SET SRRBC 6 7 SRRC 8 STRC 9 STRBC 10 SPFC 11 SPFFAN 12 SPPD4 13 SPPD3 14 SPED2 15 STLD 16 SPWS 17 SPLS2 18 SPLS1 19 SOCD 20 SPOD

CN1 TX24-100R-LT-H1 1 GND 2 GND 3 /1_DBL4 /1_DBL+ 5 1_CLK6 1_CLK+ 7 1_DATA08 1_DATA0+ 9 1_DATA110 1_DATA1+ 11 1_DATA212 1_DATA2+ 13 1_DATA314 1_DATA3+ 15 GND 16 GND 17 /CCDFAN 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 61 FRM_CCD1 62 CLK_CCD1 63 TXD_CCD1 64 RES_CCD1 65 RXD_CCD1 66 ADD_CCD1 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 81 GND 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 88 5V1 89 lcdDIS 90 3.3V3 91 GND 92 LCD_VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND

SPED2

Signal name SPED2

DSPF document empty detector

DSPF document empty detection

SPLS1

SPLS1

DSPF document length detector 1

DSPF document length detection (Short)

SPLS2

SPLS2

DSPF document length detector 2

DSPF document length detection (Long)

SPWS

SPWS

DSPF document size (Width) detection

STLD

STLD

/SLUMB

/SLUMB

DSPF document size (Width) detection analog data detector DSPF document tray lower limit detector DSPF paper tray lift motor

Code

Name

Function/Operation

DSPF document tray lower limit detection Lifts up and down the DSPF paper feed tray.

MX-M700N DSPF SECTION C – 1

CN4 TX25-100P-LT-H1 1 GND 2 GND 3 /1_DBL4 /1_DBL+ 5 1_CLK6 1_CLK+ 7 1_DATA08 1_DATA0+ 9 1_DATA110 1_DATA1+ 11 1_DATA212 1_DATA2+ 13 1_DATA314 1_DATA3+ 15 GND 16 GND 17 /CCDFAN 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 61 FRM_CCD1 62 CLK_CCD1 63 TXD_CCD1 64 RES_CCD1 65 RXD_CCD1 66 ADD_CCD1 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 81 GND 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 88 5V1 89 lcdDIS 90 3.3V3 91 GND 92 LCD_VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND

SCN JNT PWB

CN101 T24FAZ-SMT-TF

CN5 T24FAZ-SMT-TF GND 5V1 /BZR N.C N.C GND GND GND /F3 /F2 /F1 /F0 SEG2 SEG1 SEG0 /KEYIN 5V2 GND PD 5V2 PDSEL2 PDSEL1 PDSEL0 GND

24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

FFC-24Pin

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

GND 5V1 /BZR N.C N.C GND GND GND /F3 /F2 /F1 /F0 SEG2 SEG1 SEG0 /KEYIN 5V2 GND PD 5V2 PDSEL2 PDSEL1 PDSEL0 GND

MFP OPE PWB

Type Transmission type Transmission type Transmission type Volume resistor Transmission type Stepping motor

NOTE Sensor Sensor Sensor Other detector Sensor

B. Paper feed and paper transport section

SPFM

SCOV SPFC SPED1

STUD SPPD1

STRRBC

STRRC STRBC PHNR-2-H 1 2

5V2 SCOV GND

B3B-PH-K-S 3 2 1

B3B-PH-K-S 3 5V2 SPPD1 2 GND 1

B3B-PH-K-S 3 5V2 SPED1 2 1 GND

5V2 STUD GND

B3B-PH-K-S 3 2 1

PHNR-2-H PHNR-2-H +BU2P-TR-P-H 1 2 /STRC 24V3 1 2

PHNR-3-H +BU3P-TR-P-H PHNR-3-H /STRBC 1 3 2 2 N.C 3 24V3 1

SCOV

Signal name SCOV

SPFM

SPFM1

SPFC

Code

STRC

PHNR-2-H +BU2P-TR-P-H 2 /SPFC 1 24V3

CN5

B14B-PH-K-S 1 /SPFC 2 24V3 3 SCOV 4 GND 5 SPPD1 6 GND 7 SPED1 8 GND 9 STUD 10 GND 11 5V2 12 5V2 13 5V2 14 5V2 CN3 B34B-PHDSS-B 1 OUT /SLUMB 2 /STRC 3 OUT /SLUMA 4 /STRBC 5 OUT SLUMB 6 /SRRBC 7 OUT SLUMA 8 /SRRC 9 GND 10 GND 11 GND 12 GND 13 GND 14 GND 15 GND 16 GND 17 5VPOD 18 GND 19 5V2 20 GND 21 5V2 22 5V2 23 5V2 24 5V2 25 VAREF 26 N.C 27 24V3 SRRBC 28 5V2 29 24V3 FAN 30 24V3 STRBC 31 24V3 STRC 32 24V3 SRRC 33 24V3 PM 34 N.C

SPPD2 DSPF PWB

5V2

CN4 B4B-PH-K-S 5V2 SPPD2 GND N.C

1 2 3 4

CN1 B12B-PH-K-S SPFMB1 /SPFMB1 /SPFMA1 SPFMA1 24V3 24V3 24V3 24V3 SPFMA2 /SPFMA2 /SPFMB2 SPFMB2

12 11 10 9 8 7 6 5 4 3 2 1

CN6 B5B-PH-K-S /STRRC 24V3 24V3 N.C /STRRBC

1 2 3 4 5

Name

B3B-PH-K-S 3 5V2 SPPD2 2 1 GND

SMR-06V-N

SMP-06V-NC

6 5 4 3 2 1

6 5 4 3 2 1

24V3 24V3 (SPFMA1) (/SPFMA1) (/SPFMB1) (SPFMB1)

PHNR-2-H PHNR-2-H +BU2P-TR-P-H /STRRC 1 2 1 24V3 2

PHNR-3-H +BU3P-TR-P-H 3 2 1

PHNR-3-H

/STRRBC N.C 24V3

1 2 3

Function/Operation

DSPF cover switch

DSPF cover open/close detection

SPFC

DSPF paper feed motor, paper transport motor DSPF paper feed clutch

Drives the paper feed roller and the transport roller. (DSPF) DSPF paper feed section roller ON/OFF control

STRRC

STRRC

DSPF NO.1 resist roller clutch

DSPF resist roller ON/OFF control

STRRBC

STRRBC

DSPF No.1 resist roller brake clutch

DSPF resist roller braking

STRC

STRC

DSPF paper transport roller 2 clutch

DSPF transport roller 2 ON/OFF control

STRBC

STRBC

DSPF transport roller 2 braking

SPED1

SPED1

DSPF paper transport roller 2 brake clutch DSPF document upper limit detector

SPPD1

SPPD1

SPPD2

SPPD2

STUD

STUD

DSPF document paper detector 1 DSPF document paper detector 2 DSPF document tray upper limit detector

DSPF document upper limit DSPF document paper detection 1 DSPF document paper detection 2 DSPF document tray upper limit detection

MX-M700N DSPF SECTION C – 2

Type Transmission type Stepping motor Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Transmission type Transmission type Transmission type Transmission type

NOTE Sensor

Sensor Sensor Sensor Sensor

C. CIS section

CIScnt PWB CN3 9604S-35F

FFC-35Pin

Code CIS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

SD7 GND SD6 GND SD5 GND SD4 GND SD3 GND SD2 GND SD1 GND SD0 GND /LST GND SCLK GND LD GND DATA GND CLK GND LGATE GND SCN GND VDS GND VAS GND VLED

Signal name CIS

CN2 B12B-PHDSS-B 1 SD7 2 SD6 3 SD5 4 SD4 5 SD3 6 SD2 7 SD1 8 SD0 9 /LST 10 SCLK 11 GND 12 GND CN1 B26B-PHDSS 2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ /2_DBL/2_DBL+ GND FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 3.3V3 3.3V3 24V3 GND 12V2 GND 5V2 GND 5V2 /CISSET

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

SCN cnt PWB

BR BR BR BR BR BR BR BR GY BR BR BR BR BR BR BR OR OR RD GY PL GY BL GY BL BR

BR BR BR BR BR BR BR BR GY BR BR BR BR BR BR BR OR OR RD GY PL GY BL GY BL BR

CN10 S26B-PHDSS-B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ /2_DBL/2_DBL+ GND FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 3.3V3 3.3V3 24V3 GND 12V2 GND 5V2 GND 5V2 /CISSET

Name CIS control PWB/CIS unit

CIS unit

Function/Operation Scans document images (back surface) and controls the CIS unit.

MX-M700N DSPF SECTION C – 3

Type

NOTE

D. Paper exit section

SPSM

SRRBC

SRRC SPOD SPPD4

SOCD

SPPD3

DSPF PWB

SMR-12V-N

B3B-PH-K-S 5V2 3 SPPD4 2 GND 1

1 2 3 4 5 6 7 8 9 10 11 12

B3B-PH-K-S 5V2 3 2 SPPD3 GND 1

PHNR-2-H 1 2

PHNR-3-H 1 2 3

5V2 SOCD GND

SMP-12V-NC

5V2 SPPD4 GND 5V2 SPPD3 GND 5V1 SPED2 GND 5V2 STLD GND

1 2 3 4 5 6 7 8 9 10 11 12

PHNR-2-H +BU2P-TR-P-H /SRRC 24V3

2 1

PHNR-3-H +BU3P-TR-P-H /SRRBC N.C 24V3

3 2 1

CN3 B34B-PHDSS-B 1 OUT /SLUMB 2 /STRC 3 OUT /SLUMA 4 /STRBC 5 OUT SLUMB 6 /SRRBC 7 OUT SLUMA 8 /SRRC 9 GND 10 GND 11 GND 12 GND 13 GND 14 GND 15 GND 16 GND 17 5VPOD 18 GND 19 5V2 20 GND 21 5V2 22 5V2 23 5V2 24 5V2 25 VAREF 26 N.C 27 24V3 SRRBC 28 5V2 29 24V3 FAN 30 24V3 STRBC 31 24V3 STRC 32 24V3 SRRC 33 24V3 PM 34 N.C

5V2

B3B-PH-K-S 3 2 1

B3B-PH-K-S SPOD 3 2 GND 5VPOD 1

12 11 10 9 8 7 6 5 4 3 2 1

CN2 B32B-PHDSS-B GND GND VAREF N.C 24V3 SPPD2 24V3 SCOV 5V2 SPPD1 /SPFMA SPED1 SPFMA STUD /SPFMB SPFMO1 SPFMB SPFMO2 STRRC STRRBC /SLUMA /SLUMB SLUMA SLUMB SPF SET SRRBC SRRC STRC STRBC SPFC GND GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

SMR-06V-B 6 5 4 3 2 1

SMP-06V-BC

/SPFMB2 24V3 SPFMB2 SPFMA2 24V3 /SPFMA2

6 5 4 3 2 1

CN12 S22B-PHDSS-B 1 GND 2 GND 3 VAREF 4 5V1 5 24V3 6 SPPD2 7 24V3 8 SCOV 9 5V2 10 SPPD1 11 /SPFMA 12 SPED1 13 SPFMA 14 STUD 15 /SPFMB 16 SPFMO1 17 SPFMB 18 SPFMO2 19 STRRC 20 STRRBC 21 GND 22 GND CN11 S20B-PHDSS-B 1 /SLUMA 2 /SLUMB 3 SLUMA 4 SLUMB 5 SPF SET 6 SRRBC 7 SRRC 8 STRC 9 STRBC 10 SPFC 11 SPFFAN 12 SPPD4 13 SPPD3 14 SPED2 15 STLD 16 SPWS 17 SPLS2 18 SPLS1 19 SOCD 20 SPOD

SCN cnt PWB

SOCD

Signal name SOCD

DSPF open/close detector

DSPF open/close detector

SPOD

SPOD

DSPF paper exit detector

DSPF paper exit detection

SPPD3

SPPD3

DSPF document paper detection 3

SPPD4

SPPD4

SRRC

SRRC

DSPF document paper detector 3 DSPF document paper detector 4 DSPF No.2 resist roller clutch

DSPF transport roller 3 ON/OFF control

SRRBC

SRRBC

DSPF No.2 resist roller brake clutch

DSPF transport roller 3 braking

SPSM

LSPFH2

DSPF paper exit motor

DSPF paper exit motor (DSPF)

Code

CN1 B12B-PH-K-S SPFMB1 /SPFMB1 /SPFMA1 SPFMA1 24V3 24V3 24V3 24V3 SPFMA2 /SPFMA2 /SPFMB2 SPFMB2

Name

Function/Operation

DSPF document paper detection 4

MX-M700N DSPF SECTION C – 4

Type Transmission type Transmission type Transmission type Transmission type Electromagnetic clutch Electromagnetic clutch Stepping motor

NOTE Sensor Sensor Sensor Sensor

2. Operational descriptions A. Outline Sheet documents are automatically fed and transported for continuous scanning. The front and the back surfaces of duplex sheet documents can be scanned at a time.

1

2

9 No. 1

Document tray

Name

2 3 4 5 6 7 8 9 10

Pickup roller Document feed roller Separation roller No.1 resist roller (Drive) Transport roller 1 (Drive) Transport roller 2 (Drive) No.2 resist roller (Drive) Paper exit roller (Drive) CIS unit

10

8

3 4

5

6

7

Function/Operation Paper feed tray for documents. Max. loading capacity of documents: 150 sheets (80g/m2) or 19.5mm or less. Picks up a document and transports it to the document feed roller. Feeds documents. Separates paper to prevent against double feed. Performs document feed resist. Transports documents. Transports documents. Makes synchronization between the document lead edge and the scan start position. Discharges documents. Scans the back surface of a document.

B. Timing chart To increase the document replacement speed, preliminary feed is performed for the second and the following documents when two or more documents of A4/Letter size or smaller are scanned. For this purpose, each transport roller is provided with a clutch to perform independent control. In addition, an electromagnetic brake is employed for each transport roller because it reduces the motor load when compared with the mechanical brake. Transport speed 360mm/s COPY key ON

Letter (216mm) 65 sheets (Single surface) ON simultaneously with print start OFF when the last paper SPOD off

SPFFAN Fan motor SPFMCLK1, 2 Timer from SPF motor ON

167 ms (60mm)

SPFC Document feed clutch

30 ms

STRRBC Document transport resist brake clutch

50 ms (18mm) 10 ms 5 ms

67 ms (24mm) SIM adjustment STRRC Document transport resist clutch

STRC Document transport clutch

5 ms

167 ms (60mm) 67 ms SIM adjustment 10 ms

50 ms (18mm)

5 ms 36 ms SIM adjustment 10 ms

STRBC Document transport brake clutch

50 ms

5 ms 10 ms

First sheet: Paper feed start after booting the motor (Clutch ON) Off at 24mm (67ms) from SPPD1 on (SIM adjustment) ON again after 30ms from OFF, and OFF after 60mm (167ms) Second and the following sheets: The 2nd sheet start simultaneously with SPPD1 off (Clutch ON) OFF at 24mm (67ms) from SPPD1 on (SIM adjustment) ON simultaneously with SRRC on, and OFF after 60mm (167ms) First sheet ON simultaneously with the second ON of SPFC (paper feed CL) OFF after 18mm (50ms) from SPPF1 off Second and the following sheets ON simultaneously with SRRC on OFF after 18mm (50ms) from SPPD1 off First sheet ON simultaneously with SPPD1 on Second and the following sheets OFF before10ms of STRRC on ON after 5ms of STRRC off First sheet ON simultaneously with STRRC and OFF simultaneously with SPPD3 on ON before 36ms (SIM adjustment) of SRRC on ON after 5ms of STRC off OFF before 10ms of STRC on

SPPD1 Document transport sensor 1 SPPD2 Document transport sensor 2 SPPD3 Document transport sensor 3 SRRC Resist clutch

50 ms (18mm)

50 ms (18mm)

923 ms 10 ms

10 ms

ON when scan ready OK (cycle time 923ms) OFF after 18mm (50ms) of SPPD3 off

SRRBC Resist brake clutch

ON simultaneously with SPPD3 on OFF before 10ms of SRRC on

SPPD4 Document transport sensor 4 Default 37mm (102.8ms) Scanner scan

SIM adjustment (Image lead edge alignment)

Default 26mm (72.3ms) SIM adjustment (Image rear edge alignment)

CIS scan SPOD Document exit sensor

MX-M700N DSPF SECTION C – 5

C. Document tray lift operation

3. Disassembly and assembly

When a job is started, the document tray is lifted until a document at the top in the document tray turns on the document upper limit sensor (STUD).

A. External outfit section

The pressure between the document at the top in the document tray and the take-up roller is maintained at a constant level to improve the paper feed capability.

No. (1)

When paper to be scanned is exhausted, the document empty sensor (SPED1) turns off and the document tray moves down automatically until the lower limit sensor detects it.

Unit DSPF unit

No. a b

Parts Cabinet Document mat

(1)

Up and down movements of the document tray are performed by the lift motor (normal rotation, reverse rotation) and the lift gear.

(1)-a

(1) STUD

DSPF unit

1)

Push down the fixing plate.

2)

Remove the rear cover.

3)

Remove the harness.

SPED1

STLD

D. Document feed, transport, scan, paper exit, and operating speed The document fed by the take-up roller is sent through the paper feed roller and the transport roller to the resist roller section. In the resist roller section, the document lead edge and the scan start position are synchronized. The document is transported to the scan section. After being scanned, the document discharged to the document exit tray by the paper exit roller. The document transport speed varies depending on the scan mode and the scan magnification ratio as shown below. Scanning mode

Magnification ratio

Single surface scan Single surface scan Duplex scan Duplex scan

Up to 117% 118% or above Up to 100% 101% or above

Document transport speed 360mm/sec 220mm/sec 220mm/sec 110mm/sec

E. The original scan The CIS ( Image Sensor) unit is the type image scan sensor, and is assembled to the DSPF to scan document images. The LED light in the CIS unit is radiated to a document, and the reflected light is ed through the lens to the photoelectric conversion elements to form images. (Pixel: 7196 pixels, resolution: 600dpi) The CIS and the CCD assembled in the lens unit allow simultaneous scan of duplex surfaces of a document.

MX-M700N DSPF SECTION C – 6

(1)-b

(1)-a

[Note for assembly]

2)

Open the DSPF, and remove the screws.

3)

Unhook the claws on the tray side to remove the front cover.

4)

Remove the rear cover.

• Install the earth terminal in the direction shown in the figure below.

45

4)

5)

Remove the fixing screw.

Remove the DSPF.

b. Document mat 1)

Open the DSPF.

a. Cabinet 1)

Open the cover, and remove the screws.

MX-M700N DSPF SECTION C – 7

2)

B. The paper feed tray section

Remove the mat.

No. (1)

Unit Document tray unit

(2)

Others

No. a b c a b c

Parts DSPF document length detector 1 DSPF document length detector 2 DSPF document size (Width) detection analog data detector DSPF paper tray lift motor DSPF paper tray lower limit detector DSPF document empty detector

(2)-a

(1)

(1)-b

[Caution when attaching] • Place the mat on the document base glass surface; close the DSPF to attach the mat; then open again and apply pressure by hand to attach.

(1)-a (1)-c

(2)-c (2)-b

(1)

The document tray section

1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Disconnect the connector, and remove the document tray unit.

a. DSPF document length detector 1 b. DSPF document length detector 2 c. DSPF document size (Width) detection analog data detector 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document tray unit.

3)

Remove the screw, and remove the cover.

(See “B-(1) Document tray unit”)

MX-M700N DSPF SECTION C – 8

4)

Disconnect the connector, and remove the DSPF document length detector 1 (A) and the DSPF document length detector 2 (B).

(2)

Others

a. DSPF paper tray lift motor 1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Remove the DSPF paper tray lift motor.

B A

5)

Remove the rotation tray unit.

b. DSPF paper tray detector c. DSPF document empty detector 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document tray unit.

3)

Disconnect the connector, and remove the DSPF paper tray detector (A) and the DSPF document empty detector(B).

(See “B-(1) Document tray unit”)

B A

6)

Remove the DSPF document size (width) detection analog data detector.

MX-M700N DSPF SECTION C – 9

C. Paper feed and paper transport section No. (1)

Unit Paper feed unit

Parts

a b c d

Paper feed roller Pickup roller DSPF paper feed clutch DSPF document tray upper limit detector DSPF document upper limit detector DSPF cover switch DSPF document paper detector 1 Separation roller DSPF paper feed/paper transport motor DSPF resist roller brake clutch DSPF resist roller clutch No.1 resist roller (Drive) Torque limiter DSPF paper transport roller 2 brake clutch DSPF paper transport roller 2 clutch Transport roller 2 (Drive) Transport roller 1 (Drive) DSPF document paper detector 2

f g Others

a b c d e f g h i j k

(1)

(1)-a

b. Pickup roller

No.

e

(2)

a. Paper feed roller

Mainte nance ✕{ ✕{

1)

Pull up the lever and open the upper cover.

2)

Remove the roller cover.

3)

Remove the pawl, and remove the paper feed roller (A) and pickup roller (B).

✕{

✕{ ✕

✕{ ✕{

(1)-b (1)-e (1)-g (1)-d (1)-f (1)-c

(2)-b (2)-c (2)-d (2)-g

(2)-f

B

(2)-h (2)-j (2)-a

(1)

(2)-e (2)-i (2)-k

Paper feed unit

1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Disconnect the connector, and remove the paper feed unit.

MX-M700N DSPF SECTION C – 10

A

c. DSPF paper feed clutch

(2)

d. DSPF document tray upper limit detector

a. Separation roller

e. DSPF document upper limit detector

1)

Remove the paper feed roller and the pickup roller. (See “C-(1)-a. Paper feed roller” and “C-(1)-b. Pickup roller”)

2)

Remove the cover.

3)

Unhook the claw to remove the . Remove the reverse roller.

f. DSPF cover switch

Others

g. DSPF document paper detector 1 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document feed tray unit.

3)

Remove the cover.

(See “C-(1) Paper feed unit”)

4)

Remove the E-ring, and remove the DSPF the paper feed clutch.

[Caution when attaching] • Rotate the roller into the pin slot. b. DSPF paper feed/paper transport motor

5)

1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Remove the DSPF paper feed/paper transport motor.

Disconnect the connector, and remove the DSPF document tray upper limit detector (A), the DSPF document upper limit detector (B), the DSPF cover switch (C), and the DSPF document paper detector 1 (D).

A

B C

D

MX-M700N DSPF SECTION C – 11

c. DSPF resist roller brake clutch

6)

Remove the bearing reception fixture, and remove the torque limiter.

7)

Remove the electromagnetic clutch.

8)

Remove the resin E-ring, and remove the bearing.

9)

Slide the No. 1 resist roller drive in the arrow direction, and remove the plastic E-ring.

d. DSPF resist roller clutch 1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Disconnect the connector, and remove the clamp, the plastic Ering, the DSPF resist roller brake clutch (A), and the DSPF resist roller clutch (B).

B A

(See “C-(2)-c. DSPF resist roller brake clutch”)

e. No.1 resist roller (Drive) f. Torque limiter 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document feed tray unit.

3)

Remove the plastic E-ring in the arrow direction and remove the No. 1 resist roller idle.

(See “C-(1) Paper feed unit”)

4)

Remove the separation roller. (See “C-(2)-a. Separation roller”)

5)

Remove the paper feed paper guide lower unit in the arrow direction. 10) Remove No. 1 resist roller (Drive) in the arrow direction.

MX-M700N DSPF SECTION C – 12

g. DSPF paper transport roller 2 brake clutch

6)

Remove the belt. Remove No. 1 resist roller (Drive).

7)

Remove the resin E-ring, and remove the bearing.

8)

Remove the electromagnetic clutch.

h. DSPF paper transport roller 2 clutch 1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Disconnect the connector, and remove the plastic E-ring, the DSPF paper transport roller 2 brake clutch (A), and the DSPF paper transport roller 2 clutch (B).

B A

i. Transport roller 2 (Drive) j. Transport roller 1 (Drive) 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the paper feed tray unit. (See “C-(1) Paper feed unit”)

3)

Remove the No. 1 resist roller idle and the paper feed paper guide lower unit. (See “C-(2)-e. No. 1 resist roller (Drive)”)

4)

Remove the resin E-ring on cover, and remove link lever.

(See “C-(2)-g. DSPF paper transport roller 2 brake clutch” and “C-(2)-h. DSPF paper transport roller 2 clutch”) 9)

5)

Remove the resin E-ring on shaft side.

Remove the resin E-ring, and remove the bearing. 10) Remove the lever and shaft.

MX-M700N DSPF SECTION C – 13

(1)

11) Remove Transport roller 2 (Drive).

CIS control PWB/CIS unit

1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document tray unit.

3)

Remove the harness. Remove the PWB cover.

4)

Remove each cables, and remove the PWB.

5)

Loosen the hinge screws to lower the two fittings.

(See “B-(1) Document tray unit”)

k. DSPF document paper detector 2 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document feed tray unit. (See “C-(1) Paper feed unit”)

3)

Remove the No. 1 resist roller idle, the paper feed paper guide lower unit, and the No. 1 resist roller drive.

4)

Remove the transport roller 1 (Drive).

5)

Disconnect the connector, and remove the DSPF document paper detector 2.

(See “C-(2)-e. No. 1 resist roller (Drive)”) (See “C-(2)-j. Transport roller 1 (Drive)”.)

D. CIS section No. (1)

Parts CIS control PWB/CIS unit

Mainte nance ✕{

(1)

MX-M700N DSPF SECTION C – 14

6)

Open the DSPF, attach the DSPF drop preventing stopper, and remove the paper guide.

• Clean the paper guide glass surface.

E. Paper exit section No.

7)

(1) (2) (3) (4) (5) (6) (7) (8) (9)

Remove the earth, and remove the CIS.

Mainte nance

Parts DSPF paper exit motor DSPF paper transport roller 3 brake clutch DSPF paper transport roller 3 clutch No.2 resist roller (Drive) Paper exit roller (Drive) DSPF document paper detector 3 DSPF document paper detector 4 DSPF paper exit detector DSPF open/close detector

(9)

✕{ ✕{

(1)

(8)

(2) (3) (4) (6) [Note installing]

(5)

(7)

• When assembling the flat cable, first attach the lower side then the upper side.

(1)

DSPF paper exit motor

1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Remove the tension SP and remove the DSPF paper feed/ paper transport motor.

CIS cnt PWB

CIS unit BLUE

MX-M700N DSPF SECTION C – 15

(2)

DSPF paper transport roller 3 brake clutch

(3)

DSPF paper transport roller 3 clutch

1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Remove the connecters.

5)

Remove the resin E-ring, and remove the DSPF paper transport roller 3 brake clutch (A), and the DSPF paper transport roller 3 clutch (B).

B

A

(4) 3)

Remove the connecter base.

No.2 resist roller (Drive)

1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document tray unit.

3)

Remove the resin E-ring, and jam disengage knob.

4)

Remove the electromagnetic clutch.

5)

Remove the rear side bearing to remove the resin E-ring spacer.

(See “B-(1) Document tray unit”)

4)

Remove the super snap band to remove the cable.

(See “E-(2) DSPF paper transport roller 3 brake clutch”)

MX-M700N DSPF SECTION C – 16

6)

(5) 1) 2)

Disconnect the connector, and remove the No. 2 resist roller drive in the arrow direction.

Disconnect the connecter, and remove the paper exit roller (Drive) in the arrow direction.

Paper exit roller (Drive) Remove the cabinet. (See “A-(1)-a. Cabinet”) Remove the document tray unit. (See “B-(1) Document tray unit”)

3)

5)

Loosen the screw, and lift the belt tension roller, and fix them with the screws. * When fixing, apply a tension to the spring.

(6)

DSPF document paper detector 3

(7)

DSPF document paper detector 4

(8)

DSPF paper exit detector

(9) DSPF open/close detector 1)

Remove the cabinet. (See “A-(1)-a. Cabinet”)

2)

Remove the document tray unit.

3)

Disconnect the connectors, and remove the DSPF document paper detector 3 (A), the DSPF document paper detector 4 (B), the DSPF paper exit detector (C), and the DSPF open/close detector (D).

(See “B-(1) Document tray unit”)

A B

C

4)

Remove the resin E-ring, and remove the bearing.

MX-M700N DSPF SECTION C – 17

D

F. Others No. (1) (2) (3)

(3) Parts

DSPF fan motor DSPF PWB Drive unit

Drive unit

1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Remove the electromagnetic clutch.

3)

Loosen the screw, and lift the belt tension roller, and fix them with the screws. * When fixing, apply a tension to the spring.

(1)

(1)

(3)

(2)

DSPF fan motor

1)

Remove the rear cover. (See “A-(1)-a. Cabinet”)

2)

Disconnect the connecter, and remove the DSPF fan motor.

REVERSE

4)

(2)

Remove the drive unit.

DSPF PWB

1)

Remove the rear cover.

2)

Disconnect the connecter, and remove the DSPF PWB.

(See “A-(1)-a. Cabinet”)

MX-M700N DSPF SECTION C – 18

4. Maintenance ✕ : Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name DSPF Paper feed

Transport section Paper exit section Drive section

No. 1 2 3 4 5 6 7 8

Part name Pickup roller Paper feed roller Separation roller Torque limiter Resist roller Transport roller Exposure section (CIS unit) Paper exit roller

9 10 11

Gears (Grease) Belts Sensors

Others

✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

{ { { ✕ { { { {

(Note 1) (Note 1) (Note 1) (Note 1)

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

✕ ✕ ✕

UKOG-0299FCZZ

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Cleaning is air spraying

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • DSPF section: 100K or 1 year • Torque limiter: 800K

1

8

7

5

2

6

3

5

4

6

9 9 9

10

9 10 10

MX-M700N DSPF SECTION C – 19

MX-M700N [D] SCANNER SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram MHPS

CIS unit

Copy lamp unit CL

Scanner motor

CCD PWB CCD lens unit

1

MHPS

CIS unit

Copy lamp unit

6

11 10 9 8

2 MIMDA CL1

3 4

CCD PWB

7 6

5 4

SCN JNT PWB

FFC-40Pin

SLD5R-1 (FCI) GND GND /CL1 24V3 24V3

1 2 3 4 5

FFC-5Pin

CN2 IL-FPR-40S-VF-E1500 40 GND 39 1_DATA3+ 38 1_DATA337 1_DATA2+ 36 1_DATA235 1_DATA1+ 34 1_DATA133 1_DATA0+ 32 1_DATA031 GND 30 1_CLK+ 29 1_CLK28 GND 27 /1_DBL+ 26 /1_DBL25 GND 24 FRM_CCD1 23 /PAGE1 22 CLK_CCD1 21 ADD_CCD1 20 TXD_CCD1 19 RXD_CCD1 18 RES_CCD1 17 GND 16 3.3V3 15 3.3V3 14 GND 13 5V2 12 5V2 11 5V2 10 5V2 9 5V2 8 5V2 7 5V2 6 5V2 5 GND 4 12V2 3 12V2 2 GND 1 GND

CN3 SLD5R-1 (FCI) 1 GND 2 GND 3 /CL1 4 24V3 5 24V3

CN4 TX25-100P-LT-H1 GND 1 GND 2 /1_DBL3 4 /1_DBL+ 1_CLK5 6 1_CLK+ 1_DATA07 1_DATA0+ 8 1_DATA19 1_DATA1+ 10 11 1_DATA21_DATA2+ 12 1_DATA313 1_DATA3+ 14 GND 15 GND 16 /CCDFAN 17 12V2 18 24V3 19 24V3 20 PDSEL1 21 PDSEL2 22 23 /KEYIN SEG0 24 GND 25 GND 26 lcdS+ 27 lcdS28 29 lcdM+ lcdM30 lcd1+ 31 lcd132 lcd2+ 33 34 lcd235 lcdD0+ 36 lcdD0lcdD1+ 37 38 lcdD139 lcdD2+ lcdD240 lcdD3+ 41 lcdD342 GND 43 GND 44 YH 45 46 /XL 47 /STSET 48 /STMPS GND 49 GND 50 51 GND 52 GND 12V2 53 12V2 54 55 GND 56 5V2 GND 57 5V2 58 59 GND 60 3.3V3 FRM_CCD1 61 CLK_CCD1 62 63 TXD_CCD1 RES_CCD1 64 RXD_CCD1 65 ADD_CCD1 66 67 GND PAGE1 68 GND 69 GND 70 /CL1 71 PDSEL0 72 5V2 73 PD 74 SEG1 75 SEG2 76 GND 77 /F0 78 GND 79 /F1 80 GND 81 /F2 82 GND 83 /F3 84 GND 85 /BZR 86 GND 87 5V1 88 lcdDIS 89 3.3V3 90 GND 91 LCD_VEE 92 TH 93 /CCFT 94 /YL 95 XH 96 24V3 97 24V3 98 GND 99 GND 100

CN1 TX24-100R-LT-H1 1 GND 2 GND 3 /1_DBL4 /1_DBL+ 5 1_CLK6 1_CLK+ 7 1_DATA08 1_DATA0+ 9 1_DATA110 1_DATA1+ 11 1_DATA212 1_DATA2+ 13 1_DATA314 1_DATA3+ 15 GND 16 GND 17 /CCDFAN 18 12V2 19 24V3 20 24V3 21 PDSEL1 22 PDSEL2 23 /KEYIN 24 SEG0 25 GND 26 GND 27 lcdS+ 28 lcdS29 lcdM+ 30 lcdM31 lcd1+ 32 lcd133 lcd2+ 34 lcd235 lcdD0+ 36 lcdD037 lcdD1+ 38 lcdD139 lcdD2+ 40 lcdD241 lcdD3+ 42 lcdD343 GND 44 GND 45 YH 46 /XL 47 /STSET 48 /STMPS 49 GND 50 GND 51 GND 52 GND 53 12V2 54 12V2 55 GND 56 5V2 57 GND 58 5V2 59 GND 60 3.3V3 61 FRM_CCD1 62 CLK_CCD1 63 TXD_CCD1 64 RES_CCD1 65 RXD_CCD1 66 ADD_CCD1 67 GND 68 PAGE1 69 GND 70 GND 71 /CL1 72 PDSEL0 73 5V2 74 PD 75 SEG1 76 SEG2 77 GND 78 /F0 79 GND 80 /F1 81 GND 82 /F2 83 GND 84 /F3 85 GND 86 /BZR 87 GND 88 5V1 89 lcdDIS 90 3.3V3 91 GND 92 LCD_VEE 93 TH 94 /CCFT 95 /YL 96 XH 97 24V3 98 24V3 99 GND 100 GND

CIScnt PWB

CN1 B26B-PHDSS

CN10 S26B-PHDSS-B

2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ /2_DBL/2_DBL+ GND FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 3.3V3 3.3V3 24V3 GND 12V2 GND 5V2 GND 5V2 /CISSET

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

2_DATA12_DATA1+ 2_DATA02_DATA0+ 2_CLK2_CLK+ /2_DBL/2_DBL+ GND FRM_CCD2 CLK_CCD2 PAGE2 ADD_CCD2 TXD_CCD2 RES_CCD2 RXD_CCD2 3.3V3 3.3V3 24V3 GND 12V2 GND 5V2 GND 5V2 /CISSET

CN3 9604S-35F

SD7 GND SD6 GND SD5 GND SD4 GND SD3 GND SD2 GND SD1 GND SD0 GND /LST GND SCLK GND LD GND DATA GND CLK GND LGATE GND SCN GND VDS GND VAS GND VLED

SCN cnt PWB

MX-M700N SCANNER SECTION D – 1

CN6 B3B-PH-K-S MHPS GND 5V2

1 2 3

CN7 S6B-PH-K-R MIMA MIMB /MIMA /MIMB 24V3 24V3

1 2 3 4 5 6

53053-0310(MOLEX) 1 MHPS 2 GND 3 5V2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

FFC-35Pin

Code MIM MHPS

Signal name MIM MHPS

Name

Function/Operation

CIS unit

Scanner (reading) motor Scanner home position sensor detector CIS unit

CCD PWB

CCD PWB

CL1 No. 1 2 3 4 5 6 7 8

CL1

Scanner lamp

9

Name Scanner drive belt Pulley Lens Scanner drive wire Reflector No. 3 mirror No. 2 mirror White balance sheet for DSPF (CIS)/ DSPF scanning glass CIS unit

10

CCD PWB

Type

Drives the scanner (reading) section. Scanner home position detection.

Stepping motor Transmission type

NOTE

Sensor

-type image scan sensor unit. Back document image scan. Front document image scan. (Document table/DSPF mode) Converts the document images (optical signals) into electrical signals. Illuminates the document. (Xenon lamp)

Function/Operation Transmits the scanner motor power to the scanner unit. Drives the scanner drive wire. Reduces the document images (optical) and radiates them onto the CCD. Transmits the scanner motor power to the copy lamp unit and the mirror base unit. Condenses the copy lamp lights. Assures the optical path from No. 2 mirror to the CCD. Assures the optical path from No. 1 mirror to No. 3 mirror. The white reference sheet for scanning with the CIS unit. -type image scan sensor unit. Back document image scan. Front document image scan. (Document table/DSPF mode) Converts the document images (optical signals) into electrical signals.

2. Operational descriptions A. Outline There are following three methods of scanning documents in this machine. • Place a document on the table glass. The copy lamp unit is operated to radiate copy lamp light onto the document, scanning the document with the CCD. • The DSPF feeds a document. The copy lamp light is radiated onto the document which is stopped at the specified position and the document is scanned by the CCD. • The DSPF feed a document. The LED light of the CIS unit which is attached to the DSPF is radiated to the back of the document, and the document is scanned by the CIS.

B. Description (1)

CCD/Lens unit

This machine employs the reduction optical-type line CCD (Charge Coupled Device) of scan resolution of 600dpi and 7400 pixels. CCD scan is performed by shifting the scan positions sequentially by the carriage unit (lamp and mirror) scan or moving the document with the DSPF. Lights reflected by the document are reflected by each mirror to form images on CCD elements through the reduction-type lens. The CCD converts the optical energy into electrical energy (analog). (Photoelectric conversion)

(2)

CIS unit

The image sensor which scans back document images is attached to the DSPF. The close- type image sensor ( Image Sensor) with scan resolution of 600dpi and 7196 pixels is employed. For the CIS to scan documents, the scan position is sequentially shifted by shifting the document by the DSPF, and the LED light in the unit is radiated to the back of the document, and photo energy is converted into electric energy (analog signal).

CIS

Selfoc lens

CIS UNI

Lens center line

LED PWB Glass Focus point

MX-M700N SCANNER SECTION D – 2

(3)

Image signal flow

The image signal converted into electric energy (analog signal) is A-D converted on the CCD PWB. Image processes such as white balance and shading correction are performed on the scanner control PWB. The image signal is then sent through the mother board to the MFP control PWB. In the MFP control PWB, image process is performed according to the setting content of the operation . The image data are converted into laser lighting signals (VIDEO signals), and sent through the mother PWB and the PCU to the LSU (Laser Scan Unit). In the LSU, the VIDEO signals are converted into laser beams, which are radiated onto the drum.

CIS

Copy lamp unit HDD

CCD UN

MOTHER PWB

MFP CONTROL PWB

DRUM

LSU

(4)

Carriage (lamp unit) shift (scan) speed

The carriage scan speed depends on the copy magnification ratio. Speed up to 171% = 220mm/s Speed of 172% - 400% = 110mm/s

(5)

Timing chart

Platen timing chart

MM Feed

MIMD MHPS

Return

Home position

Home position Scan

CCD PSW DSPF duplex timing chart

SPFM 1030mS

SRRC SPPD4 94mS

SPOD CCD

181mS

55mS

CIS MX-M700N SCANNER SECTION D – 3

PCU PWB

3. Disassembly and assembly

(1)

A. Scanner section

1)

Remove the DSPF unit.

2)

Remove the table glass. (See “a. Table glass”)

3)

Remove the lock connector. (For dehumidifier heater)

4)

Remove the flat cable, the connector, and harness from the cable clamp.

5)

Remove the right side cabinets upper and lower.

6)

Remove the screw and the fixing plate.

No. (1)

Unit Scanner unit

Scanner unit (See “A-(1) DSPF unit” in the “DSPF section”)

No.

Parts

a b c d e f g h i j k l m n o p q r s

Table glass Slit glass (DSPF scan mode) Mirror Lens Reflector Scanner dry heater Rails Drive belt Drive wire Pulley Scanner lamp Inverter PWB CCD PWB lens unit Scanner relay PWB Scanner motor Scanner FLASH PWB Scanner control PWB DSPF open/close detector Scanner home position sensor detector Document size detection light emitting PWB Document size detection light reception PWB

t u

Mainte nance { { { { { ✩ ✕ ✕ ✕

{

(1)-c (1)-e (1)-d

(1)-i (1)-b

(1)-g

(1)-f (1)-i

(1)-h

(1)-j (1)-g

(1)-j

(1)-s (1)-l

(1)-a

(1)-q (1)-p (1)-t (1)-r

(1)-k

(1)-o

(1)-u

(1)-n

(1)-m

(1)

MX-M700N SCANNER SECTION D – 4

7)

a. Table glass

Remove the tray.

b. White standard glass (When scanner iinternal maintenance)

8)

9)

1)

Loosen the screws in the hinge section, and lower the two metal fixtures.

2)

Open the DSPF, and slide the DSPF drop-preventing stopper pin of the Hinge L to the drop preventing position.

Remove the left side cabinets front and rear.

Remove the screws.

10) Hold the both sides of the scanner base, and slide it toward you to remove.

3)

Remove the right glass holder.

4)

Using a cloth, etc. on the right glass surface to prevent fingerprints, remove the cover.

5)

Remove the white reference glass unit.

* When assembling or disassembling the table glass, check that the glass does not cover the steel plate on the front side.

MX-M700N SCANNER SECTION D – 5

c. Mirror

5)

Remove the lens cover.

6)

Cary out cleaning of the lens and CCD.

7)

Cary out cleaning of the reflector.

d. Lens e. Reflector 1)

Remove the table glass. (See “a. Table glass”)

2)

Move the lamp unit.

3)

4)

Clean mirrors 2 and 3.

Remove the harnesses clamp and the dark box.

f. Scanner dry heater 1)

Remove the table glass. (See “a. Table glass”)

2)

Shift the lamp unit, and remove the dark box. (See “c. Mirror”)

3)

Remove the dark box and remove the harness clamp, and remove the scanner dry heater.

* When attaching the dark box cover, check to insure that the blade spring is in the original position.

MX-M700N SCANNER SECTION D – 6

g. Rails

3)

Remove the connector in front side.

1)

Remove the table glass. (See “a. Table glass”)

4)

2)

Grease up the rails.

Turn up the cutout mylar and remove the screw; then shift the lamp holder to the front side and take out the lamp from above on the rear side.

5)

Remove the harness connector from the hole on the front side.

h. Drive belt i. Drive wire j. Pulley 1)

Remove the table glass. (See “a. Table glass”)

2)

Check the drive belt, drive wire and pulley. l. Inverter PWB 1)

Remove the table glass. (See “a. Table glass”)

2)

Remove the core guide.

3)

Unhook the claw to remove the plastic on the rear side.

4)

While holding to prevent from falling, remove the screw fixing to remove the inverter PWB.

k. Scanner lamp 1)

Remove the table glass. (See “a. Table glass”)

2)

Remove the core guide to shift the optical lamp unit to the base plate cutout section.

5)

Disconnect the lamp connectors.

6)

Release the connector lock on the inverter PWB to remove the FC cable.

[Caution when attaching] • Place each harness on the rib.

MX-M700N SCANNER SECTION D – 7

m. CCD PWB lens unit

n. Scanner relay PWB

1)

Remove the table glass. (See “a. Table glass”)

1)

Remove the table glass. (See “a. Table glass”)

2)

Remove the harnesses clamp and the dark box.

2)

Remove the harness cover B.

3)

Disconnect the connector, and remove the scanner interface PWB.

3)

Mark the lens unit plate position by pen.

o. Scanner motor

4)

Release the connector lock on the CCD PWB to remove the FC cable.

5)

Remove the screw to remove the CCD PWB lens unit.

6)

1)

Remove the rear cabinet.

2)

Remove the spring and disconnect the connector.

Attach the CCD PWB lens unit to the marked position.

MX-M700N SCANNER SECTION D – 8

3)

4)

Remove the scanner motor unit.

4)

Remove the scanner control PWB unit.

5)

Remove the scanner control PWB.

Remove the scanner motor.

r. DSPF open/close detector 1)

Remove the rear cabinet. (See “o. Scanner motor”)

2)

Disconnect the connector, and remove the DSPF open/close detector. * When disconnecting the connector, hold the housing section and slide straightly to remove.

p. Scanner FLASH PWB q. Scanner control PWB 1)

Remove the rear cabinet. (See “o. Scanner motor”)

2)

Release the lock, and remove the scanner FLASH PWB.

s. Scanner home position sensor detector

3)

1)

Remove the rear cabinet. (See “o. Scanner motor”)

2)

Remove the DSPF harness holder B.

Remove the clamp, and disconnect the connector. * Do not disconnect the PCN harness connector.

MX-M700N SCANNER SECTION D – 9

3)

Disconnect the connector, and remove the scanner home position sensor.

4)

Remove the document detection arm lower, and remove the document detection light emitting unit.

t. Document size detection light emitting PWB 1)

Remove the DSPF unit. (See “A-(1) DSPF unit” in the “DSPF section”)

2)

Disconnect the connector and the earth terminal, and remove the upper cabinet rear.

u. Document size detection light reception PWB 1)

Remove the operation base plate A.

2)

Remove the document size detection light receiving PWB, and disconnect the connector.

[Note for assembly]

3)

Remove the document detection fulcrum TIG, and remove the document detection arm unit.

• First, connect the harness to the PWB, and check that PWB parts are properly connected. Then attach the PWB to the PWB holder.

MX-M700N SCANNER SECTION D – 10

4. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Scanner section

No. 1 2 3 4 5 6 7 8 9 10 11 12

Part name Mirror Lens Reflector Sersors Table glass Dust-proof glass OC White standard glass Rails Drive belt Drive wire Pulley

{ { { { { { { {

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

{ { { { { { { { ✩ ✕ ✕ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

6

7

9 7 1 1 8 10

3 1

11 12 5 2 4 11

9

12

MX-M700N SCANNER SECTION D – 11

MX-M700N

[E] MANUAL PAPER FEED SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

MM

MPFC MFPUS

4

MPFD1

MTOP2 MTOP1

MPED

MPFPWS

DSW-R

MPLD2 MPLD1 MPFGS

123 PHNR-09-H+BU09P-TR-P-H DRAWER QR/P4-24S-C(01)/QR/P4-24P-C(01)

PCU PWB

S5B-PH-K-S GND2 +5V2 /MM MMCLK MM-T

1 2 3 4 5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

CN-17 B30B-PHDSS-B M2LUM +24V1 GND2 /T1PFC +24V1 +24V1 /M2PFC /DSKPFC2 GND2 GND2 TXD-FIN +5V2 RXD-FIN /MM /DTR-FIN MMCLK /DSR-FIN MM-T RES-FIN TSW-LED (NC) TSW GND2 GND2 TANSET GND2 +5V2 DSW-DSK (NC) +5V2

CN-13 B26B-PHDSS-B DSW-F(R) 1 2 (NC) 3 (NC) 4 GND2 5 +24V1 6 MPLD1 7 /MFPUS 8 +5V2 9 GND2 10 MPLD2 11 MPED 12 MTOP1 13 +5V2 14 MTOP2 15 +24V1 MPFPWS 16 17 /MPFGS Vref 18 +5V-MPFD1 19 /MPFC 20 MPFD1 21 +24V1 22 GND2 23 GND2 24 25 (NC) 26 DSW-R

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

DSW-F(R) 1 2 GND2 3 MPLD1 4 +5V2 5 MPLD2 6 MTOP1 7 MTOP2 8 GND2 MPFPWS 9 10 Vref 11 /MPFC 12 +24V1 13 +24V1 14 /MFPUS 15 GND2 16 MPED 17 +5V2 18 +24V1 /MPFGS 19 +5V-MPFD1 20 21 GND2 22 MPFD1 23 (NC) DSW-R 24

1 2 3 4 5 6 7 8 9

GND2 MPLD1 +5V2 MPLD2 MTOP1 MTOP2 GND2 MPFPWS Vref

9 8 7 6 5 4 3 2 1

DF3-3S-2C 1 GND2 2 MPLD1 3 +5V2 DF3-3S-2C 1 GND2 2 MPLD2 3 +5V2 179228-2 1 MTOP1 2 GND2 179228-2 1 MTOP2 2 GND2 PHR-3 1 GND2 2 MPFPWS 3 Vref PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 (NC) 2 1 /MPFC 3 SMR-02V-N/SMP-02V-NC 1 1 +24V1 2 2 /MFPUS DF3-3S-2C 1 GND2 2 MPED 3 +5V2 SMR-02V-N/SMP-02V-NC 1 1 +24V1 2 2 /MPFGS PHR-3 1 +5V-MPFD1 2 GND2 3 MPFD1

MX-M700N MANUAL PAPER FEED SECTION E – 1

MPED

Signal name MPED

MPFD1

MPFD1

MPFPWS

MPFPWS

MPLD1

MPLD1

MPLD2

MPLD2

MTOP1

MTOP1

MTOP2

MTOP2

DSW-R

DSW-R

MPFC

MPFC

MFPUS

MFPUS

MPFGS

MPFGS

Code

No. 1 2 3 4

Name

Function/Operation

Manual feed paper empty detector Manual feed paper detector 1 Manual feed paper width detector Manual feed paper length detector 1 Manual feed paper length detector 2 Manual tray pull-out position detector 1 Manual tray pull-out position detector 2 Manual feed unit open/close Switch Paper feed clutch (Manual paper feed) Paper pickup solenoid (Manual paper feed) Manual paper feed gate solenoid

Name Separation roller (Manual paper feed tray) Paper feed roller (Manual paper feed tray) Paper pickup roller (Manual paper feed tray) Torque limiter

Manual paper feed tray paper empty detection Manual tray paper detection Manual feed paper width detection Manual paper feed tray paper length detection (Paper feed side) Manual paper feed tray paper length detection (Outside) Manual paper feed tray pull-out position detection (Storing position) Manual paper feed tray pull-out position detection (Pull-out position) Manual paper feed unit open/close detection, Main charger power source, Developing bias power line open/close. Controls the manual paper feed section paper feed roller ON/ OFF. Presses the paper pickup roller onto paper. Manual feed gate solenoid open/close control.

Type

NOTE

Transmission type Transmission type Volume resistor

Manual paper feed unit Paper transport system sensor Analog detector

Transmission type Transmission type type

Manual paper feed unit Manual paper feed unit Manual paper feed unit Manual paper feed unit

type Micro switch Electromagnetic clutch Electromagnetic solenoid Electromagnetic solenoid

Function/Operation Separates paper to prevent against double feed. Feeds paper to the paper transport section. Sends paper to the paper feed roller. A fixed level of resistance is applied to the paper separation roller to prevent against double feed.

2. Operational descriptions A. Outline The paper feed tray 1 holds 900 sheets, the paper feed tray 2 holds 1,300 sheets, the multi-purpose paper feed tray 3 holds 500 sheets, the paper feed tray 4 holds 500 sheets, and the manual paper feed tray holds 100 sheets. Those paper feed units are standard provisions.

3. Disassembly and assembly No. A

Unit Multi manual paper feed tray unit

No.

Parts

a

Manual paper feed unit open/ close switch Manual feed empty detector Pickup roller Paper feed roller Separation roller Torque limiter Manual feed gate solenoid Manual feed paper detector 1 Paper feed clutch Paper pickup solenoid Manual paper width size detection PWB Manual feed paper length detector 1 Manual feed paper length detector 2 Manual tray pull-out position detector 1 Manual tray pull-out position detector 2

b c d e f g h i j k l m n o

Mainte nance

(1) (1)-f (1)-j (1)-i (1)-h (1)-b

(1)-n

(1)-o

✕{ ✕{ ✕{ ✕

(1)-a

(1)-g (1)-d (1)-k (1)-c (1)-e

MX-M700N MANUAL PAPER FEED SECTION E – 2

(1)- l (1)- m

A. Multi manual paper feed tray unit 1)

Pull out the multi manual paper feed tray unit.

2)

Remove the multi manual paper feed tray unit from the left and right accuride.

4)

(2)

(1)

Manual feed empty detector

1)

Pull out the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the manual feed upper cover. (See "A-(1) Manual paper feed unit open/close switch")

3)

Remove the pickup cover.

4)

Remove the actuator unit.

5)

Remove the manual feed empty detector.

Manual paper feed unit open/close switch

1)

Pull out the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the manual feed upper cover.

3)

Remove the manual paper feed unit open/close switch.

Remove the manual feed front cover.

MX-M700N MANUAL PAPER FEED SECTION E – 3

(3)

Pickup roller

(6) Torque limiter

(4)

Paper feed roller

1)

Pull out the multi paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the bottom cover.

3)

Remove the separation roller.

4)

Remove the separation roller shaft, and remove the torque limiter.

(5)

Separation roller

1)

Pull out the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the actuator unit. (See "A-(2) Manual empty detector")

3)

Unhook the claw to remove the pickup roller.

4)

Unhook the claw to remove the paper feed roller.

5)

Remove the separation roller cover.

6)

Remove the separation roller.

MX-M700N MANUAL PAPER FEED SECTION E – 4

(7) 1)

Manual feed gate solenoid

(9)

Paper feed clutch

Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

1)

Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the bottom cover. (See "A-(4) Torque limiter")

2)

Remove the upper cover. (See "A-(1) Pickup roller")

3)

Disconnect the connector, and remove the manual paper feed gate solenoid unit.

3)

Remove the front cover.

4)

Remove the manual gate solenoid.

4)

Remove the interface earth plate, the E-ring, and the bearing, and remove the manual paper feed mounting plate.

5)

Remove the connector and E-ring, and remove the paper feed clutch.

* When assembling, tighten the screw so that the lever tip is at 13 r 0.5mm from the frame edge with the solenoid plunger pulled.

13 5mm

(8) 1)

Manual feed paper detector 1 Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the bottom cover. (See "A-(4) Torque limiter")

3)

Disconnect the connector, and remove the manual paper feed paper detector 1.

* When assembling, fit the rotation stopper of the paper feed clutch with the clutch fixing screw.

MX-M700N MANUAL PAPER FEED SECTION E – 5

(10) Paper pickup solenoid

(11) Manual paper width size detection PWB

1)

Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

1)

Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the manual paper feed upper cover and the pickup upper cover. (See"A-(1) Pickup roller")

2)

Remove the multi tray 250 lower.

3)

Remove the front cover, and remove the manual paper feed mounting plate. (See "A-(7) Paper feed clutch")

4)

Remove the spring.

3)

Remove the width detection mounting plate.

5)

Disconnect the connector, and remove the paper pickup solenoid unit.

4)

Remove the pawl and the connector, and remove the manual paper feed VR PWB.

6)

Remove the paper pickup solenoid.

[Note installing] Check that there is a clearance when the solenoid plunger is pulled.

4.2mm

MX-M700N MANUAL PAPER FEED SECTION E – 6

(12) Manual feed paper length detector 1

B. Others

(13) Manual feed paper length detector 2

1)

(14) Manual tray pull-out position detector 1

Slide the harness holder in the direction of Y and install it. The band must be in the range of A. Pull section B in the arrow direction to give a slack to the harness.

(15) Manual tray pull-out position detector 2 1)

Remove the multi manual paper feed tray unit. (See "A. Multi manual paper feed tray unit")

2)

Remove the multi tray 250 lower. (See "A-(11) Manual paper width detection PWB")

3)

Remove the manual tray lower.

4)

Disconnect the connector, and remove the manual feed paper length detector 1 (A) and manual feed paper length detector 2 (B).

B X Band

A

B

A Y 2)

5)

Disconnect the connector, and remove the manual paper feed tray pull-out position detector 1(A) and the manual paper feed tray pull-out position detector 2 (B).

Fold the harness with your fingers and check that the harness keeps the folded shape along the holder when it is released. Rib C must be separated from the harness.

C

B

A

MX-M700N MANUAL PAPER FEED SECTION E – 7

4. Maintenance ✕: Check

▲: Replace

{: Clean

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.) 55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Multi manual paper feed

No. 1 2 3 4 5

Part name Pickup roller Paper feed roller Separation roller Torque limiter Shaft (Conductive grease)

✕ ✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

{ { { ✕ ✩

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(Note 1) (Note 1) (Note 1) (Note 1) UKOG-0012QSZZ

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • Manual paper feed: 100K or 1 year • Torque limiter: 400K

4 1

5 5

2 3

5

5

MX-M700N MANUAL PAPER FEED SECTION E – 8

MX-M700N [F] TRAY PAPER FEED SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram A. Paper feed tray 1, 2 section

PHR-2 1 T1LUM 2 GND2

PCU PWB

SMR-02V-N/SMP-02V-NC 1 +24V1 1 2 /T1PUS 2

CN-14 B24B-PHDSS-B 1 T1LUM 2 T2LUM 3 GND2 4 GND2 5 +24V1 6 +24V1 7 /T1PUS 8 /T2PUS 9 +5V2 10 +24V1 11 GND2 12 /DSKLS 13 T1LUD 14 GND2 15 T1PED 16 T1SPD 17 +5V2 18 +5V2 19 GND2 20 GND2 21 T2LUD 22 T2SPD 23 T2PED 24 +5V2

CN-17 B30B-PHDSS-B 1 M2LUM 2 +24V1 3 GND2 4 /T1PFC 5 +24V1 6 +24V1 7 /M2PFC /DSKPFC2 8 9 GND2 10 GND2 TXD-FIN 11 +5V2 12 RXD-FIN 13 /MM 14 /DTR-FIN 15 MMCLK 16 /DSR-FIN 17 MM-T 18 RES-FIN 19 TSW-LED 20 (NC) 21 TSW 22 GND2 23 GND2 24 TANSET 25 GND2 26 +5V2 27 DSW-DSK 28 (NC) 29 +5V2 30 CN-12 B30B-PHDSS-B +24V1 1 +24V1 2 /T2PFC 3 4 /HPLS +24V1 5 DVCH1 6 7 /HPFC DVCH2 8 +24V1 9 DVCH3 10 11 /PSBC DVCH4 12 +5V2 13 +24V1 14 PPD 15 TCS 16 GND2 17 GND2 18 +5V-MPRD1 19 TSGOUT 20 21 GND2 GND2 22 MPRD1 23 +5V2 24 +5V-MPRD2 25 HUS-DV 26 GND2 27 GND2 28 MPRD2 29 30 TH-DV

PHR-2 1 T2LUM 2 GND2 SMR-02V-N/SMP-02V-NC 1 +24V1 1 2 2 /T2PUS

MM SMR-04V-N/SMP-04V-NC 1 1 +5V2 2 2 GND2 3 3 T1LUD 4 4 T1PED

SMP-10V-NC/SMR-10V-N 1 +5V2 1 2 GND2 2 3 T2LUD 3 4 T2PED 4 5 GND2 5 6 T1SPD 6 7 +5V2 7 8 GND2 8 9 T2SPD 9 10 +5V2 10

S4B-PH-K-S +5V2 GND2 T1LUD T1PED

1 2 3 4

S4B-PH-K-S +5V2 GND2 T2LUD T2PED

T1PUS

PHR-3 1 GND2 2 T1SPD 3 +5V2

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 (NC) 2 1 /T1PFC 3

T1PFC

PHR-3 1 GND2 2 T2SPD 3 +5V2

S5B-PH-K-S 1 GND2 2 +5V2 3 /MM 4 MMCLK 5 MM-T

1 2 3

1 2 3 4

T1S PWB

T1LUM

T2PFC

8

PHR-3 GND2 TANSET +5V2

TANSET T1SPD

8

5 7 6

T2LUM T2S PWB

T2SPD T2PUS

4

1

1 7 6 5

3 2 3 4

1 2

PHNR-03-H+BU03P-TR-P-H 3 +24V1 1 2 (NC) 2 1 /T2PFC 3

MX-M700N TRAY PAPER FEED SECTION F – 1

T1SPD

Signal name T1SPD

T2SPD

Code

Name

Function/Operation

Type

Paper remaining quantity detector (Paper feed tray 1)

Paper remaining detection (Paper feed tray 1)

Transmission type

T2SPD

Paper remaining quantity detector (Paper feed tray 2)

Paper remaining detection (Paper feed tray 2)

Transmission type

TANSET

TANSET

Paper feed tray1, 2 (1, 2 tray unit ) insertion detection

T1PFC

T1PFC

T2PFC

T2PFC

T1LUM

T1LUM

Paper feed tray1, 2 (1, 2 tray unit) detection signal Paper feed clutch (Paper feed tray 1) Paper feed clutch (Paper feed tray 2) Paper feed tray lift-up motor (Paper feed tray 1)

Drives the lift plate of the paper feed tray.

Transmission type Electromagnetic clutch Electromagnetic clutch DC brush motor

T2LUM

T2LUM

Paper feed tray lift-up motor (Paper feed tray 2)

Drives the lift plate of the paper feed tray.

DC brush motor

T1PUS

T1PUS

Presses the paper pickup roller onto paper.

T2PUS

T2PUS

MM

MM

Paper pickup solenoid (Paper feed tray 1) Paper pickup solenoid (Paper feed tray 2) Main motor

Electromagnetic solenoid Electromagnetic solenoid DC brushless motor

T1S PWB

T1S PWB

T2S PWB

T2S PWB

No. 1 2 3 4 5 6 7 8

Paper feed tray 2 section roller ON/OFF control

Presses the paper pickup roller onto paper.

Detector PWB (Paper feed tray 1, 2 paper feed unit ) (Paper feed tray 1) Detector PWB (Paper feed tray 1, 2 paper feed unit ) (Paper feed tray2)

Name Lift wire Paper feed table Paper feed tray unit 1, 2 regulation plates L/R Pulley Paper pickup roller Separation roller Paper feed roller Torque limiter

Paper freed tray 1 section roller ON/OFF control

Drives the paper feed trays 1, 2, 3, and 4, and the manual paper feed section. Paper tray upper limit detection and paper empty detection

NOTE Paper feed tray remaining quantity sensor Paper feed tray remaining quantity sensor Paper feed tray system sensor

Selection of Rotation mode/ Brake mode Selection of Rotation mode/ Brake mode

Paper

Paper tray upper limit detection and paper empty detection

Function/Operation Transmits the paper tray lift moter to power the paper feed tray. Paper is put on this table. Regulates the paper width to restrict skew to the minimum. Transmits the paper tray lift-up motor power to the paper feed tray. Sends paper to the paper feed roller. Separates paper to prevent against double feed. Feeds paper to the paper transport section. Provides a certain level of resistance power for the paper separation roller rotation to prevent against double feed.

MX-M700N TRAY PAPER FEED SECTION F – 2

B. Paper feed tray 3, 4 section

11 10 9

11

8

7

9

8

MM

7

10

PHR-2 M2LUM GND2

1 2 1 2 3 4 5 6 7 8 9 10

PHNR-02-H+BU02P-TR-P-H 2 1 +24V1 2 /M2PFC 1

M1LUM

M1LUD

11

1 2 3 4 5 6 7 8 9 10

SMR-10V-N/SMP-10V-NC

M1PFC

DSKPFC1

M2LUM GND2 +24V1 /M2PFC GND2 TXD-FIN RXD-FIN /DTR-FIN /DSR-FIN RES-FIN

S5B-PH-K-S GND2 +5V2 /MM MMCLK MM-T

12

1 2 3 4 5

M2LUM

M1PFD S6B-PH-K-S (NC) 1 2 GND2 3 M1SS1 M1SS2 4 M1SS3 5 6 M1SS4

M1PUS M2PFC

9 8 7

M1SPD

2

M1PED

PHR-3 GND2 M1SPD +5V2

M1SS PWB

SMP-18V-NC/SMR-18V-N 1 1 GND2 2 2 M1SS1 3 3 M1SS2 4 4 M1SS3 5 5 M1SS4 6 6 GND2 7 7 M1SPD 8 +5V2 8 9 9 (NC) 10 GND2 10 11 M2SS1 11 12 M2SS2 12 13 M2SS3 13 14 M2SS4 14 15 GND2 15 16 M2SPD 16 17 +5V2 17 18 (NC) 18

1 2 3

S6B-PH-K-S 1 (NC) 2 GND2 3 M2SS1 4 M2SS2 M2SS3 5 M2SS4 6

1

PHR-3 GND2 M2SPD +5V2

1

1 2 3

M1PWS

3

5

PHR-3 GND2 1 M1PED 2 +5V2 3 PHR-3(RED) GND2 1 M1LUD 2 +5V2 3

6

SMR-11V-N/SMP-11V-NC 1 +24V1 1 2 /M1PUS 2 3 GND2 3 4 M1PED 4 5 +5V2 5 6 GND2 6 7 M1LUD 7 8 +5V2 8 9 +5V-M1PFD 9 10 GND2 10 11 M1PFD 11

PHR-3 +5V-M1PFD 1 2 GND2 M1PFD 3

12

M2PFD SMP-02V-NC/SMR-02V-N SMR-11V-N/SMP-11V-NC 1 1 +24V1 1 +24V1 1 2 /M2PUS 2 2 /M2PUS 2 3 GND2 3

10 9 8 7

SMP-02V-NC/SMR-02V-N 1 1 +24V1 2 /M1PUS 2

4 M2LUD

11

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

PHR-3 GND2 1 M2PED 2 +5V2 3

M2PUS M2SPD

2

M2SS PWB

1

M2PED

PHR-3(RED) GND2 1 M2LUD 2 +5V2 3

4 5 6 7 8 9 10 11

M2PED 4 +5V2 5 GND2 6 M2LUD 7 +5V2 8 +5V-M2PFD 9 GND2 10 M2PFD 11

PHR-3 +5V-M2PFD 1 GND2 2 M2PFD 3

PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /M1PFC 1 PHR-2 M1LUM 1 2 GND2 PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /DSKPFC1 1 Soldering Vref 3 1 GND2 M1PWS 2

5 6

4

3

MX-M700N TRAY PAPER FEED SECTION F – 3

SMR-03V-N/SMP-03V-NC 1 Vref 1 2 GND2 2 3 M1PWS 3

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

CN-17 B30B-PHDSS-B M2LUM +24V1 GND2 /T1PFC +24V1 +24V1 /M2PFC /DSKPFC2 GND2 GND2 TXD-FIN +5V2 RXD-FIN /MM /DTR-FIN MMCLK /DSR-FIN MM-T RES-FIN TSW-LED (NC) TSW GND2 GND2 TANSET GND2 +5V2 DSW-DSK (NC) +5V2

CN-15 B34B-PHDSS-B DSW-F (NC) GND2 GND2 /GBPWM /MHVREM MHV-T /THV+PWM THV+REM /CHV-PWM /CHV-REM /CHVAWM /CHVACREM /DVPWM /DVREM HVREM +24V1 (NC) GND2 GND2 M1SS1 M2SS1 M1SS2 M2SS2 M1SS3 M2SS3 M1SS4 M2SS4 GND2 GND2 M1SPD M2SPD +5V2 +5V2

CN-16 B32B-PHDSS-B +24V1 +24V1 /M1PUS /M2PUS GND2 GND2 M1PED M2PED +5V2 +5V2 GND2 GND2 M1LUD M2LUD +5V2 +5V2 +5V-M1PFD +5V-M2PFD GND2 GND2 M1PFD M2PFD +24V1 +24V1 /M1PFC /DSKPFC1 M1LUM Vref GND2 GND2 (NC) M1PWS

PCU PWB

M1LUD

Signal name M1LUD

M1PED

M1PED

M1PFD

M1PFD

M1PWS

M1PWS

M1SPD

M1SPD

M2LUD

M2LUD

M2PED

M2PED

M2PFD

M2PFD

M2SPD

M2SPD

M1PFC

M1PFC

M2PFC

M2PFC

DSKPFC1

DSKPFC1

M1PUS

M1PUS

M2PUS

M2PUS

MM

MM

Code

M2SS PWB No. 1

Name Paper feed tray upper limit detector (Paper feed tray 3) Paper empty detector (Paper feed tray 3) Paper detector (Multi Paper feed tray 3) Paper feed tray paper width detector (Paper feed tray 3) Paper remaining quantity detector (Paper feed tray 3)

Paper tray upper limit detection (Paper feed tray 3) Paper empty detection (Paper feed tray 3) Paper feed tray 3 paper detection

Paper Paper feed tray upper limit detector (Paper feed tray 4) Paper empty detector (Paper feed tray 4) Paper detector (Multi Paper feed tray 4) Paper remaining quantity detector (Paper feed tray 4)

Paper tray upper limit detection (Paper feed tray 4) Paper empty detection (Paper feed tray 4) Paper feed tray 4 paper detection

Paper feed clutch (Paper feed tray 3) Paper feed clutch (Paper feed tray 4) Paper feed tray 3, 4 paper transport clutch 1 Paper pickup solenoid (Paper feed tray 3) Paper pickup solenoid (Paper feed tray 4) Main motor

Paper freed tray 3 section roller ON/OFF control

Paper size detection PWB

Name Paper size detection plate

2 3

Paper width guide R Paper size detection rotation plate

4 5 6 7 8 9 10

Paper size (length) guide plate Paper width guide L Lift plate Paper pickup roller Separation roller Paper feed roller transport roller 8 (Paper feed tray 3) transport roller 5 (Paper feed tray 4) transport roller 10 (Paper feed tray 3) transport roller 7 (Paper feed tray 4) Torque limiter

11 12

Function/Operation

Paper width detection of multi Paper feed tray (Paper feed tray 3) Paper remaining detection (Multi Paper feed tray 3)

Paper remaining quantity detection (Paper feed tray 4)

Paper freed tray 4 section roller ON/OFF control Paper feed tray 3, 4 section paper transport roller ON/ OFF control Presses the paper pickup roller onto paper. Presses the paper pickup roller onto paper. Drive the paper feed tray 1, 2, 3 and 4, and the manual paper feed section. Paper remaining detection

Type Transmission type Transmission type Transmission type Slide resistor Transmission type Transmission type Transmission type Transmission type Transmission type Electromagnetic clutch Electromagnetic clutch Electromagnetic clutch Electromagnetic solenoid Electromagnetic solenoid DC brush-less motor

NOTE Paper feed tray system sensor Paper feed tray system sensor Paper transport system sensor Analog detector Paper feed tray remaining quantity sensor Paper feed tray system sensor Paper feed tray system sensor Paper transport system sensor Paper feed tray remaining quantity sensor

Paper

Function/Operation Changes its own position in conjunction with the paper size (length) adjustment lever. By this operation, the paper size detector detects the paper size. Suppresses skew to the minimum by restricting the paper width. Changes its own position in conjunction with the paper size (length) adjustment lever. By this operation, the paper size detection plate position is changed and the paper size detector detects the paper size. Regulates the paper size (length). By restricting the paper width, skew is restricted to the minimum. Lifts the paper to maintain the paper feed position at the fixed position. Sends paper to the paper transport section. Separate paper to prevent against double feed Feeds paper to the paper transport section. Transports paper from the paper feed tray 3 to the transport rollers 9 and 10. Transports paper from the paper feed tray 4 to the transport rollers 6 and 7. Transports paper from the transport rollers 7 and 8 to the transport roller 11. Transports paper from the transport roller 5 to the transport roller 10. Provides a certain level of resistance power for the paper separation roller rotation to prevent against double feed.

MX-M700N TRAY PAPER FEED SECTION F – 4

2. Operational descriptions A. Outline Paper feed tray 1 holds 900 sheets, paper feed tray 2 holds 1,300 sheets. The multi-purpose paper feed tray 3 holds 550 sheets, the paper feed tray 4 holds 550 sheets, and the manual paper feed tray holds 100 sheets. Those paper feed units are standard provisions.

B. Paper feed tray 1, 2 section (1)

Paper feed operation

a. Preliminary operation before paper feed 1)

Set paper in the tray, and insert the tray into the machine. The tray sensor turns on.

2)

The lift-up motor operates to lift the tray.

3)

The paper upper limit sensor turns on to stop the tray at the specified position.

b. Paper feed operation 1)

When copy/print operation is started, the motors (MM, FUM, VPM, and TRM) and the clutch (TRC) are turned on to turn on the solenoid (T1PUS) at the timing of paper pickup. This rotates and falls the take-up roller to pick up paper.

2)

At the same time, the paper feed roller rotates to feed paper to the transport section. At that time, the separation roller rotates to prevent against double feed of paper.

500mS

MM

500mS

FUM

870mS

T1PFC 79mS

T1PUS VPM TRM RRC POM1

50mS

79mS

50mS

74mS 164mS 439mS

POM2

500mS 120mS

500mS

PFD2 PPD POD1 POD2

C. Paper size of paper feed trays detection method (1)

Paper size of paper feed trays detection method

a. Paper feed tray1, 2 paper feed unit (Paper feed tray 1, 2) The paper feed tray 1 is used exclusively for A4 (11 x 8.5) paper size. The paper feed tray 2 is used for A4, 11 x 8.5, or B5 paper size. To change the paper size, change the paper guide and change the set value of SIM 26-2.

MX-M700N TRAY PAPER FEED SECTION F – 5

(2)

Paper size of paper feed trays detection method

a. Multi-purpose paper feed tray (Paper feed tray 3), 500 sheets paper feed tray (Paper feed tray 4) 1)

Paper width detection The paper width is calculated with the VR voltage value (A/D conversion value) linked with the side guide plate. Paper width and paper size (set in the range of standard value r 6 [mm]). Width size Detection pattern A B C D E F G

2)

Paper size

Standard [mm]

Range[mm]

A3/A4 WLT/LT B4/B5 LG/LTR/Foolscap A4R Exective-R B5R

297.0 279.4 257.0 215.9 210.0 184.1 182.0

303.0 to 291.0 285.4 to 273.4 263.0 to 251.0 221.9 to 209.9 216.0 to 204.0 190.1 to 178.1 188.0 to 176.0

Paper size detection The paper size detection is made by the combination of the cassette paper size detector 1 to 4.

CSS1 CSS2

CSS4 CSS3 Relationship between each paper size detector detection and paper size Vertical size detection Pattern 1 2 3 4 5 6 7 0

3)

Detection SW state CSS1

CSS2

CSS3

CSS4

ON OFF OFF OFF ON ON ON OFF

ON ON ON OFF OFF OFF ON OFF

OFF OFF ON ON ON ON ON OFF

ON ON ON ON ON OFF OFF OFF

AB size

B5 Extra A4 LT B5R EX-R A4R LTR Foolscap Extra B4 LGL A3 WLT Paper feed tray not attached

Size detection combinations Paper size

Width detection pattern

B5 A4 B5R A4R Foolscap B4 A3 LT EX-R LTR LGL WLT

C A G E D B A B F D D B

Inch size

Vertical detection pattern 1 2 3 4 5 6 7 2 3 4 6 7

MX-M700N TRAY PAPER FEED SECTION F – 6

Width of detection range 147.0 to 198.0 198.0 to 237.0 237.0 to 274.0 274.0 to 314.0 314.0 to 347.0 347.0 to 389.0 389.0 to 432.8

D. Paper remaining detection (1)

Paper remaining detection

Remaining paper detection is performed according to four stages, i.e. three stages with paper and one stage with no paper, and the result is displayed.

(2)

Detection method

The number of remaining sheets is determined according to the number of times the remaining paper sensor changes from the time the paper feed tray starts lifting up to the time when the upper detection sensor comes ON.

(Figure showing state transition of the remaining paper detection sensor during tray elevation and changes in status according to the number of remaining sheets)

The no-paper detection sensor detects the state of no remaining paper.

MED (paper sensor) Turn plate

During no-paper detection

1/3 Field Sensor logic: Low

Remaining Paper Detection Actuator

MCSPD (remaining paper detection sensor)

Remaining paper 1/3 position

2/3 Field Sensor logic: Hi

Remaining paper 2/3 position

3/3 Field Sensor logic: Low

Remaining paper 1/3 position

MX-M700N TRAY PAPER FEED SECTION F – 7

3. Disassembly and assembly

a. Pickup roller

A. Paper feed tray 1, 2 section No.

Unit

(1)

Paper feed unit (Paper feed tray 1, 2)

(2)

Others

No.

Parts

a b c d e f a

Pickup roller Paper feed roller Separation roller Torque limiter Lift wire (Rear) Lift wire (Front) Paper remaining quantity sensor PWB Paper remaining quantity detector Paper feed tray 1, 2 detection sensor Dry heater

b c d

(2)-c (1)-b

(2)-a (1)-e (1)-d (1)-b (1)-d

Mainte nance ✕{ ✕{ ✕{ ✕

1)

Pull out the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

2)

Unhook the claws to remove the paper guide.

3)

Unhook the claw to lift up the first paper feed tray feed section, and then remove the pickup roller.

(2)-a (1)-e

(1)-f (2)-b

(1)-c (1)-a

(1)

(1)-f (2)-d (2)-b (1)-c (1)-a

(1) 1)

Paper feed unit (Paper feed tray 1, 2)

b. Paper feed roller 1)

Pull out the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

2)

Unhook the claws to remove the paper guide. (See “a-1. Pickup roller”)

3)

Unhook the claw to lift up the first paper feed tray feed section, and then remove the paper feed roller.

Pull up the paper feed tray 1, 2.

2)

Remove the fixing screws from the left and right rails.

3)

Hold the grips of the position indicated in the figure with both hands, and remove it.

MX-M700N TRAY PAPER FEED SECTION F – 8

c. Separation roller

e. Lift wire (Rear)

1)

Pull out the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

1)

Remove the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

2)

Unhook the claws to remove the paper guide. (See “a-1. Pickup roller”)

2)

Remove the E-ring, slide the winding pulley, and loosen the wire.

3)

Remove the lower paper guide.

4)

Unhook the claws to remove the reverse roller.

3)

Disengage the pawl, and remove the wire.

4)

Remove the resin E-ring.

5)

Remove the wire.

d. Torque limiter 1)

Pull out the paper feed tray units 1, 2. (See “a. Paper feed unit (Paper feed tray 1, 2)”)

2)

Unhook the claws to remove the paper guide. (See “a-3. Separation roller”)

3)

Remove the separation roller unit.

4)

Remove the torque limiter.

MX-M700N TRAY PAPER FEED SECTION F – 9

* the nylon clamp.

4)

Disengage the pawl, and remove the wire.

5)

Remove the resin E-ring.

6)

Remove the wire.

* Attach so that the red wire is on the outside. * Turn it clockwise to fit with the T-shape pin position and insert.

f. Lift wire (Front) 1)

Remove the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

2)

Push down the tray and remove the screw, and remove the paper feed tray 1, 2 front cabinet.

3)

Remove the E-ring, slide the winding pulley, and loosen the wire.

* the nylon clamp. * Attach so that the red wire is on the outside. * Turn it counterclockwise and fit with the T-shape pin position and insert.

MX-M700N TRAY PAPER FEED SECTION F – 10

(2)

Others

2)

a. Paper remaining quantity sensor PWB 1)

Remove the paper feed tray units 1, 2.

2)

Disconnect the connector, and remove the paper remaining quantity sensor PWB.

Disconnect the connecter, and remove the Paper feed trays 1, 2 detection sensor.

(See “(1) Paper feed unit (Paper feed tray 1, 2)”)

d. Dry heater 1)

Remove the rear cabinet.

2)

Disconnect the connector from dehumidifier heater relay PWB.

3)

Remove the band, and remove the dry heater unit.

4)

Remove the dry heater.

(See “c. Paper feed trays 1, 2 sensor”) b. Paper remaining quantity detector 1)

Remove the paper feed tray units 1, 2. (See “(1) Paper feed unit (Paper feed tray 1, 2)”)

2)

Disconnect the connecter, and remove the paper feed tray lock arm unit.

3)

Disconnect the connecter, and remove the paper remaining quantity detector.

c. Paper feed tray 1, 2 detection sensor 1)

Remove the rear cabinet.

MX-M700N TRAY PAPER FEED SECTION F – 11

B. Paper feed tray 3, 4 section No. (1)

Unit Paper feed unit (Paper feed tray 3, 4)

No. a b c d e f g

(2)

Others

h I j a b c d

(1)-i (1)-j (1)-h (1)

Parts Pickup roller Paper feed roller Separation roller Torque limiter Paper pickup solenoid Paper feed tray upper limit detector Paper feed tray empty detector transport roller 8, 10 Transport roller 5, 7 Paper detector Paper size detection PWB Paper remaining quantity detector Paper feed tray paper width detector Dry heater

2)

Lifting up the paper feed tray unit slightly, remove it at an angle from the right side.

3)

Open the bottom left cabinet.

4)

Remove the connector cover.

5)

Disconnect the connectors.

Mainte nance ✕{ ✕{ ✕{ ✕

✕{ ✕{

(1)-d (1)-e (2)-b

(2)-a

(1)-b (1)-c (2)-d (2)-c

(1) 1)

(1)-g (1)-f (1)-a

Paper feed unit (Paper feed tray 3, 4) Pull out gently the paper feed tray it stops.

MX-M700N TRAY PAPER FEED SECTION F – 12

6)

Remove the paper feed unit (Paper feed tray 3, 4) from the lower shelf.

b. Paper feed roller 1)

Remove the paper feed unit (Paper feed tray 3, 4). (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

2)

Remove the paper guide. (See “a. Pickup roller”)

3)

Release the pawl, and remove the paper feed roller.

a. Pickup roller

c. Separation roller

1)

Remove the paper feed unit (Paper feed tray 3, 4). (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

1)

2)

Remove the paper guide.

2)

Remove the paper guide. (See “a. Pickup roller”)

3)

Disengage the pawl, and remove the separation roller.

Remove the paper feed unit (Paper feed tray 3, 4). (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

d. Torque limiter 3)

Unhook the claws to remove the pickup roller.

1)

Remove the paper feed unit (Paper feed tray 3, 4). (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

2)

Remove the E-ring, and remove the gear and the pin.

3)

Remove the E-ring and the bearing.

MX-M700N TRAY PAPER FEED SECTION F – 13

4)

Remove the separation roller unit.

5)

Remove the E-ring, and one-way clutch.

6)

Remove the E-ring, and move the separation roller shaft.

7)

Remove the shaft unit.

8)

3)

Remove the solenoid unit.

4)

Remove the paper pickup solenoid.

Remove the torque limiter.

f. Paper feed tray upper limit detector g. Paper feed tray empty detector 1)

Remove the paper feed tray 3, 4. (See “(1)Paper feed unit (Paper feed tray 3, 4)”)

2)

Remove the cover. (See “e. Paper pickup solenoid”)

3)

Remove the paper feed tray upper detector unit (a) and the paper feed tray empty detector unit (b).

e. Paper pickup solenoid 1) 2)

Remove the paper feed tray 3, 4. (See “(1)Paper feed unit (Paper feed tray 3, 4)”) Remove the cover.

b

4)

Remove the detector.

MX-M700N TRAY PAPER FEED SECTION F – 14

a

h. transport roller 8, 10

j. Paper detector

1)

1)

Remove the paper feed tray 3, 4.

Remove the paper feed tray 3, 4.

(See “(1)Paper feed unit (Paper feed tray 3, 4)”)

(See “(1)Paper feed unit (Paper feed tray 3, 4)”) 2)

Remove the cover. (See “e. Paper pickup solenoid”)

2)

Remove the cover. (See “e. Paper pickup solenoid”)

3)

Remove the E-ring and remove the pulley bearing.

3)

Remove the paper detector unit.

4)

Remove the transport roller 8, 10.

4)

Remove the paper detector.

(2)

Others

a. Paper size detection PWB 1)

Remove the paper feed tray.

2)

Disconnect the connector, and remove the paper size detection PWB unit.

3)

Release the pawl, and remove the paper size detection PWB.

(See “(1) Paper feed unit (Paper feed tray 3, 4)”)

i. Transport roller 5, 7 1)

Remove the paper feed tray 3, 4.

2)

Remove the cover. (See “e. Paper pickup solenoid”)

3)

Remove the E-ring and remove the pulley bearing.

4)

Remove the transport roller 5, 7.

(See “(1)Paper feed unit (Paper feed tray 3, 4)”)

MX-M700N TRAY PAPER FEED SECTION F – 15

b. Paper remaining quantity detector

d. Dry heater

1)

1)

Remove the paper feed tray 3, 4 unit lower.

2)

Remove the paper feed lower cover.

3)

Remove the rear cabinet.

4)

Disconnect the connector from the dehumidifying heater relay PWB.

5)

Remove the snap band.

Remove the paper feed tray. (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

2)

Disconnect the connecter, and remove the paper remaining quantity detector unit.

3)

Remove the paper remaining quantity detector cover. Remove the paper remaining quantity detector.

(See “(1) Paper feed unit (Paper feed tray 3, 4)”)

c. Paper feed tray paper width detector 1)

Remove the paper feed tray 3, 4 unit lower. (See “(1) Paper feed unit (Paper feed tray 3, 4)”)

2)

3)

Disconnect the connector, and release the pawl, and remove the width detection unit.

Remove the spring, and remove the paper width mounting base. Remove the width detection arm and remove the paper feed tray paper width detector.

MX-M700N TRAY PAPER FEED SECTION F – 16

6)

Remove the dry heater unit.

7)

Remove the dry heater.

4. Maintenance ✕: Check

▲: Replace

{: Clean

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Tray paper feed unit

No. 1 2 3 4

Part name Pickup roller Paper feed roller Separation roller Torque limiter

✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ✕

{ { { ✕

{ { { ✕

{ { { ✕

{ { { ✕

{ { { ✕

{ { { ✕

{ { { ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(Note 1) (Note 1) (Note 1) (Note 1)

(Note 1) Replacement reference: For replacement, refer to each paper feed counter value. • Paper feed tray 1 and 2: 200K or 1 year • Paper feed tray 3 and 4: 100K or 1 year • Torque limiter: 800K

4 1 2 3

4 2 1 4

2 1 3

MX-M700N TRAY PAPER FEED SECTION F – 17

3

MX-M700N [G] PAPER TRANSPORT SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram A. Vertical paper transport section 1

MM

DSKPFC2

VPM

PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /DSKPFC2 1

S5B-PH-K-S GND2 +5V2 /MM MMCLK MM-T

DSKPFC2

Signal name DSKPFC2

VPM MM

Code

1 2 3 4 5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

CN-17 B30B-PHDSS-B M2LUM +24V1 GND2 /T1PFC +24V1 +24V1 /M2PFC /DSKPFC2 GND2 GND2 TXD-FIN +5V2 RXD-FIN /MM /DTR-FIN MMCLK /DSR-FIN MM-T RES-FIN TSW-LED (NC) TSW GND2 GND2 TANSET GND2 +5V2 DSW-DSK (NC) +5V2

PCU PWB

Name

CN-10 B26B-PHDSS-B /POM1A /POM1XA /POM1B /POM1XB /POM2A /POM2XA /POM2B /POM2XB /1A /1XA /1B /1XB /2A /2XA /2B /2XB /TRMA /TRMXA /TRMB /TRMXB /VPMA /VPMXA /VPMB /VPMXB GND2 GND2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

CN-4 B26B-PHDSS-B 1 /POM1A 2 /POM1XA 3 /POM1B 4 /POM1XB 5 /POM2A 6 /POM2XA 7 /POM2B 8 /POM2XB 9 /1A 10 /1XA 11 /1B 12 /1XB 13 /2A 14 /2XA 15 /2B 16 /2XB 17 /TRMA 18 /TRMXA 19 /TRMB 20 /TRMXB 21 /VPMA 22 /VPMXA 23 /VPMB 24 /VPMXB 25 GND2 26 GND2

CN-2 B12B-PH-K-S /TRM/A 1 /TRMA 2 3 /TRMB 4 /TRM/B +24V2 5 +24V2 6 /VPM/A 7 /VPMA 8 /VPMB 9 /VPM/B 10 +24V2 11 +24V2 12

SMR-06V-N/SMP-06V-NC 1 2 3 4 5 6

/VPM/A /VPMA /VPMB /VPM/B +24V2 +24V2

1 2 3 4 5 6

DRIVER PWB

Function/Operation

Type

Paper transport roller 11 ON/OFF control.

VPM

Paper feed tray 3/4 paper transport clutch 2 Vertical paper transport motor

Drives the paper transport rollers 4 and 13.

Electromagnetic clutch Stepping motor

MM

Main motor

Drives the paper feed trays 1, 2, 3, and 4, and the manual paper feed section.

DC brush-less motor

MX-M700N PAPER TRANSPORT SECTION G – 1

NOTE

Normal speed mode Paper

B. Vertical paper transport section 2

MM RRC

1

2

TRM

3

PSBC

VPM PPD MPRD2

MPRD1

S5B-PH-K-S GND2 +5V2 /MM MMCLK MM-T

1 2 3 4 5

PHNR-02-H+BU02P-TR-P-H 1 +24V1 2 2 /RRC 1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

CN-17 B30B-PHDSS-B M2LUM +24V1 GND2 /T1PFC +24V1 +24V1 /M2PFC /DSKPFC2 GND2 GND2 TXD-FIN +5V2 RXD-FIN /MM /DTR-FIN MMCLK /DSR-FIN MM-T RES-FIN TSW-LED (NC) TSW GND2 GND2 TANSET GND2 +5V2 DSW-DSK (NC) +5V2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

CN-7 B32B-PHDSS-B +24V1 +24V1 /CFM-DV /RRC GND2 (NC) +24V1 +24V(DSW) +5V-APPD1 PFD2 +5V-APPD2 /CFM-ADU +5V-PFD2 THPS2 +5V-DSWD TURM +5V-AINPD /TCBPWH +5V-THPS1 (NC) +5V-THPS2 /TCBIAS /FBIAS APPD1 DSWD APPD2 /DGS AINPD GND2 GND2 (NC) DSW-L

PCU PWB CN-12 B30B-PHDSS-B +24V1 1 +24V1 2 /T2PFC 3 4 /HPLS +24V1 5 6 DVCH1 /HPFC 7 8 DVCH2 +24V1 9 DVCH3 10 /PSBC 11 DVCH4 12 +5V2 13 +24V1 14 PPD 15 TCS 16 GND2 17 GND2 18 +5V-MPRD1 19 TSGOUT 20 GND2 21 GND2 22 MPRD1 23 +5V2 24 25 +5V-MPRD2 HUS-DV 26 GND2 27 GND2 28 MPRD2 29 TH-DV 30

CN-10 B26B-PHDSS-B /POM1A /POM1XA /POM1B /POM1XB /POM2A /POM2XA /POM2B /POM2XB /1A /1XA /1B /1XB /2A /2XA /2B /2XB /TRMA /TRMXA /TRMB /TRMXB /VPMA /VPMXA /VPMB /VPMXB GND2 GND2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

+24V1 /PSBC +5V2 PPD GND2 +5V-MPRD1 GND2 MPRD1 +5V-MPRD2 GND2 MPRD2 +24V1 /HPLS (NC) (NC) (NC) (NC) (NC)

PHNR-06-H+BU06P-TR-P-H 6 1 +24V1 5 2 /PSBC 3 +5V2 4 4 PPD 3 5 GND2 2 6 (NC) 1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

SMR-08V-N/SMP-08V-NC 1 +5V-MPRD11 2 GND2 2 3 MPRD1 3 4 +5V-MPRD2 4 5 GND2 5 6 MPRD2 6 7 +24V1 7 8 /HPLS 8

PHNR-02-H+BU02P-TR-P-H 2 +24V1 1 1 /PSBC 2 179228-3 1 +5V2 2 PPD 3 GND2 PHR-3(RED) 1 +5V-MPRD1 2 GND2 3 MPRD1 PHR-3 1 +5V-MPRD2 2 GND2 3 MPRD2

SMR-18V-N/SMP-18V-NC

CN-4 B26B-PHDSS-B 1 /POM1A 2 /POM1XA 3 /POM1B 4 /POM1XB 5 /POM2A 6 /POM2XA 7 /POM2B 8 /POM2XB 9 /1A 10 /1XA 11 /1B 12 /1XB 13 /2A 14 /2XA 15 /2B 16 /2XB 17 /TRMA 18 /TRMXA 19 /TRMB 20 /TRMXB 21 /VPMA 22 /VPMXA 23 /VPMB 24 /VPMXB 25 GND2 26 GND2

CN-2 B12B-PH-K-S /TRM/A 1 /TRMA 2 3 /TRMB 4 /TRM/B +24V2 5 6 +24V2 7 /VPM/A 8 /VPMA 9 /VPMB 10 /VPM/B +24V2 11 12 +24V2

DRIVER PWB

MX-M700N PAPER TRANSPORT SECTION G – 2

SMR-06V-N/SMP-06V-NC 1 2 3 4 5 6

/TRM/A /TRMA /TRMB /TRM/B +24V2 +24V2

1 2 3 4 5 6

SMR-06V-N/SMP-06V-NC 1 2 3 4 5 6

/VPM/A /VPMA /VPMB /VPM/B +24V2 +24V2

1 2 3 4 5 6

MPRD1

Signal name MPRD1

MPRD2

MPRD2

PPD

PPD

RRC

Code

Name

Function/Operation

Type

Manual feed/paper feed tray 2/LCC paper detection Manual feed/paper feed tray 2/LCC paper detection Paper detection in front of resist roller

Transmission type Transmission type Reflection type

RRC

Paper feed tray 2 paper detector 1 Paper feed tray 2 paper detector 2 Resist roller front paper detector Resist roller clutch

Resist roller ON/OFF control

PSBC

PSBC

Resist roller brake clutch

Resist roller braking

MM

MM

Main motor

TRM

TRM

Resist roller front drive motor

Drives the paper feed trays 1, 2, 3, and 4, and the manual paper feed section. Drives the paper transport roller 15.

Electromagnetic clutch Electromagnetic clutch DC brush-less motor Stepping motor

VPM

VPM

Vertical paper transport motor

Drives the paper transport rollers 4 and 13.

Stepping motor

No. 1

Name Resist roller (Drive)

2

Resist roller (Idle)

3

Transport roller 15

NOTE Paper transport system sensor Paper transport system sensor Paper transport system sensor

Paper Normal speed mode/ Resist roller front paper transport timing control (Warp amount control) Normal speed mode

Function/Operation Transports paper to the transfer section. / Controls the transport timing of paper to adjust the relationship between images and paper. Applies a pressure to paper and the resist roller to provide transport power of the transport roller to paper. Transports paper to the transport resist roller.

MX-M700N PAPER TRANSPORT SECTION G – 3

C. Horizontal paper transport section

MM

1 2

3 4 HPFC

T1PPD

6

MPRD2

5

MPRD1

MPFD2

LPPD

S5B-PH-K-S GND2 +5V2 /MM MMCLK MM-T

1 2 3 4 5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

CN-17 B30B-PHDSS-B M2LUM +24V1 GND2 /T1PFC +24V1 +24V1 /M2PFC /DSKPFC2 GND2 GND2 TXD-FIN +5V2 RXD-FIN /MM /DTR-FIN MMCLK /DSR-FIN MM-T RES-FIN TSW-LED (NC) TSW GND2 GND2 TANSET GND2 +5V2 DSW-DSK (NC) +5V2

CN-12 B30B-PHDSS-B +24V1 1 +24V1 2 /T2PFC 3 /HPLS 4 +24V1 5 6 DVCH1 7 /HPFC 8 DVCH2 +24V1 9 10 DVCH3 11 /PSBC 12 DVCH4 13 +5V2 14 +24V1 15 PPD 16 TCS 17 GND2 18 GND2 +5V-MPRD1 19 TSGOUT 20 21 GND2 GND2 22 MPRD1 23 24 +5V2 +5V-MPRD2 25 HUS-DV 26 27 GND2 28 GND2 29 MPRD2 30 TH-DV

CN-18 B14B-PHDSS-B GND2 1 +5V-MPFD2 2 TXD-LCC 3 GND2 4 RXD-LCC 5 MPFD2 6 /DTR-LCC 7 +5V-LPPD 8 /DSR-LCC 9 GND2 10 RES-LCC 11 LPPD 12 /TRC-LCC 13 (NC) 14

PCU PWB

PHNR-02-H+BU02P-TR-P-H 1 2 +24V1 1 /HPFC 2

SMR-06V-N/SMP-06V-NC 1 +5V-MPFD2 1 2 GND2 2 3 MPFD2 3 4 +5V-LPPD 4 5 GND2 5 6 LPPD 6

SMP-06V-NC/SMR-06V-N 1 +5V-MPFD2 1 2 2 GND2 3 3 MPFD2 4 +5V-LPPD 4 5 5 GND2 6 LPPD 6

PHR-3 1 +5V-MPFD2 2 GND2 3 MPFD2 PHR-3 1 +5V-LPPD 2 GND2 3 LPPD

MX-M700N PAPER TRANSPORT SECTION G – 4

MPFD2

Signal name MPFD2

Manual feed paper detector 2

Manual tray and LCC unit paper detection

MM

MM

Main motor

HPFC

HPFC

Horizontal paper transport clutch

MPRD1

MPRD1

MPRD2

MPRD2

T1PPD

T1PPD

Paper feed tray 2 paper detector 1 Paper feed tray 2 paper detector 2 Paper detector (Paper feed tray 1)

Drives the paper feed trays 1, 2, 3, and 4, and the manual paper feed section. Manual paper feed, paper feed tray 2 section, LCC paper transport roller ON/OFF control Manual feed/paper feed tray 2, LCC paper detection Manual feed/paper feed tray 2/LCC paper detection Paper detection from paper feed tray 1

Code

No. 1 2 3 4 5 6

Name

Name Transport roller 15 Transport roller 4 Transport roller 3 Transport roller 2 Transport roller 13 Paper guide lock solenoid

Function/Operation

Type

NOTE

Transmission type DC brushless motor Electromagnetic clutch Transmission type Transmission type Transmission type

Paper transport system sensor Paper

Paper transport system sensor Paper transport system sensor Paper transport system sensor

Function/Operation Transports the paper to resist roller. Transports paper from the transport roller 3 to the transport roller 15. Transports paper from the paper feed tray 2 and the transport roller 2 to the transport roller 3. Transports paper from the manual paper feed and transport roller 2 to the transport roller 3. Transports to the transport roller 15. Lock the horizontal transport paper guide.

2. Operational descriptions

3. Disassembly and assembly

A. Outline

A. Vertical paper transport section 1

The paper transport section serves the function of transferring paper from each paper feed port to the registration roller section. Paper from manual feed, paper feed tray units 1 and 2 (optional), and the right paper feed tray of the paper feed tray units 1 and 2 is transported horizontally, whereas paper from the left paper feed tray of the paper feed tray units 1 and 2, paper feed tray 3 and paper feed tray 4 is transported vertically to the registration roller section.

No. (1) (2)

Unit Paper feed tray 1 and 2 left PG unit Vertical transport upper unit

After the leading edge of the paper is synchronized with the leading edge of the drum image in the registration roller section, the paper that is transfer printed with the image in the transfer section es through the fusing section and is discharged either face-down or face-up.

No.

Parts

a

Transport roller 11 (Drive)

a b

Transport roller 13 (Drive) Transport sensor

(2)-b (2)-a

(1)-a

MX-M700N PAPER TRANSPORT SECTION G – 5

(2)

Mainte nance ✕{ ✕{

(1)

(1)

Paper feed tray 1 and 2 left PG unit

1)

Open the left lower cabinet.

2)

Remove the resin E-ring, and remove the pressure fulcrum shaft.

7)

Remove the paper feed tray 1 and 2 left PG unit.

a. Transport roller 11 (Drive)

3)

Remove the left vertical transport PG stopper plate.

4)

Open the left door, and remove the left lower cabinet unit.

1)

Remove the paper feed tray 1 and 2 left PG unit. (See “(1) Paper feed tray 1 and 2 left PG unit”)

2)

Remove the E-ring, the drive collar, and the one-way gear.

3)

Remove the E-ring and the bearing, and remove the transport roller 11 (Drive).

* Be careful of the installing direction.

5)

Remove the left vertical transport PG stopper plate.

6)

Open the left vertical transport unit, and remove it.

MX-M700N PAPER TRANSPORT SECTION G – 6

(2)

Vertical transport upper unit

1)

Remove the resist roller unit. (See “B-(1) Resist roller unit”)

2)

Disconnect the connector, and remove the vertical transport upper unit.

4)

Remove the upper PG holding plate.

5)

Remove the vertical transport upper PG.

6)

Remove the transport roller 13 (Drive).

a. Transport roller 13 (Drive) 1)

Remove the vertical transport upper unit. (See “(2) Vertical transport upper unit”)

2)

Remove the upper transport fulcrum plate holder, and remove the vertical transport upper open/close PG.

3)

Remove the open/close PG earth, and remove the drive connection stopper screw and the bearing.

b. Transport sensor 1)

Remove the vertical transport upper unit. (See “(2) Vertical transport upper unit”)

2)

Check each sensors.

MX-M700N PAPER TRANSPORT SECTION G – 7

(1)

B. Vertical paper transport section 2 No. (1)

(2)

Unit Resist roller unit

Others

No.

Parts

a b c d e

Resist roller (Idle) Resist roller brake clutch Transport roller 15 Resist roller (Drive) Resist roller front paper detector Paper dust cleaner

a

Resist roller unit

1)

Open the front door, and open the process cover. Remove the process unit.

2)

Remove the paper dust removing unit.

3)

Remove the rear frame side cover, and disconnect the connector.

Mainte nance ✕{ ✕{ ✕{

✕▲

(1)-a (1)-d

(1)-b (1) (1)-e (1)-c

(2)-a

MX-M700N PAPER TRANSPORT SECTION G – 8

4)

Remove the resist roller unit.

5)

Remove the bearing, and remove the E-ring, the gear, and the pin.

b. Resist roller brake clutch 1)

Remove the resist roller unit. (See “(1) Resist roller unit”)

2)

Remove the cover. (See “a. Resist roller (Idle)”)

3)

Remove the resist roller brake clutch fixture.

4)

Remove the E-ring and the resist roller break clutch.

a. Resist roller (Idle) 1)

Remove the resist roller unit. (See “(1) Resist roller unit”)

2)

Remove the cover.

c. Transport roller 15

3)

Remove the follower roller tension spring.

4)

Remove the resist roller (Idle) unit.

1)

Remove the resist roller unit. (See “(1) Resist roller unit”)

2)

Remove the front side cover.

3)

Remove the E-ring, the gear, and the bearing.

4)

Remove the coupling bearing on the rear side.

5)

Remove the transport roller 15.

MX-M700N PAPER TRANSPORT SECTION G – 9

d. Resist roller (Drive)

e. Resist roller front paper detector

1)

Remove the resist roller unit. (See “(1) Resist roller unit”)

1)

Remove the resist roller unit. (See “(1) Resist roller unit”)

2)

Remove the follower roller and the tension spring.

2)

Remove the cover. (See “a. Resist roller (Idle)”)

3)

Remove the cover on the front side.

3)

Remove the resist roller front paper detector.

4)

Remove the transport roller 15.

5)

Remove the paper guide.

(2)

Others

a. Paper dust cleaner

6)

1)

Open the front cabinet. Open the process DV cover.

2)

Remove the paper dust cleaner.

Remove the E-ring, the gear, and the bearing.

7)

Remove the coupling on the rear side.

8)

Remove the resist roller (Drive).

MX-M700N PAPER TRANSPORT SECTION G – 10

C. Horizontal paper transport section

4)

Remove the paper feed reverse guide. Disconnect the connector, and remove the relay unit.

No. (1)

Unit Relay unit

Parts

a b c d e f

Paper guide lock solenoid Paper guides Transport roller 3 (drive) Transport roller 4 (Drive) Transport roller 2 (Drive) Paper feed tray 2 paper detector 1 Paper feed tray 2 paper detector 2 Manual paper detector 2 No. 5 paper feed paper detector

g (2)

No. 5 paper feed paper unit

a b

(1) (1)-b

Mainte nance

No.

(1)-d (1)-f (1)-g

{ ✕{ ✕{ ✕{

(1)-e

(1)-a (1)-b

(2)

(1)-c (2)-a

(1) 1)

(2)-b

Relay unit

a. Paper guide lock solenoid

Pull out the multi manual paper feed tray unit.

2)

Remove the paper feed tray units 1 and 2. (See “A-(1) Paper feed tray units 1 and 2” in the “PAPER TRANSPORT SECTION”)

3)

Remove the toner cartridge, the OPC drum, and the toner hopper, and remove the front door.

1)

Remove the relay unit. (See “(1) Relay unit”)

2)

Remove the connector, and remove the paper guide lock solenoid unit.

3)

Remove the paper guide lock solenoid.

MX-M700N PAPER TRANSPORT SECTION G – 11

b. Paper guides 1)

Remove the relay unit. (See “(1) Relay unit”)

2)

Remove the metal fixture.

3)

4)

4)

Remove the bearing, the belt, and the relay drive shaft unit.

5)

Remove the transport roller 3 and 4 (Drive).

6)

Remove the E-ring from transport roller 3 and 4 (Drive), and remove the belt pulley.

Remove the lower paper guide unit.

Clean each paper guides.

e. Transport roller 2 (Drive) c. Transport roller 3 (drive) d. Transport roller 4 (Drive) 1)

Remove the relay unit. (See “(1) Relay unit”)

2)

Remove lower paper guide unit. (See “b. Paper guides”)

3)

Remove the rear positioning plate, and remove the paper feed port PG of the paper feed tray 1 and 2.

1)

Remove the relay unit. (See “(1) Relay unit”)

2)

Remove lower paper guide unit. (See “b. Paper guides”)

3)

Remove the rear positioning plate, and remove the paper feed PG of the paper feed tray 1/2.

4)

Remove the paper entry side upper plate.

(See “c. Transport roller 3 (Drive)”)

MX-M700N PAPER TRANSPORT SECTION G – 12

5)

Remove the E-ring, and remove the gear and the belt pulley.

6)

Remove the transport roller 2 (Drive) unit.

7)

Remove the E-ring from the transport roller 2 (Drive).

(2)

No. 5 paper feed relay unit

1)

Remove the multi manual paper feed unit. (See “A-(1) Multi manual paper feed tray unit” in the “MANUAL PAPER FEED SECTION”)

2)

Remove the manual interface paper guide upper.

3)

Remove the manual feed relay paper guide upper.

4)

Lift the No. 5 paper feed relay unit, and remove the connector.

5)

Remove the No. 5 paper feed relay unit.

f. Paper feed tray 2 paper detector 1 g. Paper feed tray 2 paper detector 2 1)

Remove the relay unit. (See “(1) Relay unit”)

2)

Check the paper feed tray 2 paper detector 1 (A) and the paper feed tray 2 paper detector 2 (B). a. Manual paper detector 2 b. No. 5 paper feed relay detector 1)

B

Remove the multi manual paper feed unit. (See “A-(1) Multi manual paper feed tray unit” in the “MANUAL PAPER FEED SECTION”)

2)

Remove the No. 5 paper feed relay unit.

3)

Check the manual paper detector 2 (A) and the No. 5 paper feed relay detector (B).

A A

B

MX-M700N PAPER TRANSPORT SECTION G – 13

4. Maintenance ✕ : Check

▲: Replace

{: Clean

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust as necessary.) 55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Transport section

No. 1 2 3 4

Part name PS follower roller Transport rollers Transport paper guides Paper dust clean unit

✕ ✕ { ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { { ▲

{ { { ▲

{ { { ▲

{ { { ▲

{ { { ▲

{ { { ▲

{ { { ▲

{ { { ▲

1 2 4

2 2

2

2

2

2 2 2

2 2 2 2

MX-M700N PAPER TRANSPORT SECTION G – 14

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

MX-M700N [H] DUPLEX SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram 1

DSW-ADU

4 3

DGS

AINPD

DSW-L

APPD1

2 TURM

APPD2 THPS2

PFD2

2 1 PHR-3 1 +5V-APPD1 2 GND2 3 APPD1 PHR-3 1 +5V-APPD2 2 GND 3 APPD2

DRIVER PWB CN-5 B9B-PH-K-S /1/A /1A /1B /1/B /2/A /2A /2B /2/B +24V2

1 2 3 4 5 6 7 8 9

PCU PWB CN-7 B32B-PHDSS-B 1 +24V1 +24V1 2 3 /CFM-DV /RRC 4 5 GND2 6 (NC) 7 +24V1 +24V(DSW) 8 +5V-APPD1 9 10 PFD2 +5V-APPD2 11 /CFM-ADU 12 +5V-PFD2 13 14 THPS2 +5V-DSW 15 16 TURM +5V-AINPD 17 /TCB-PWM 18 (NC) 19 20 (NC) +5V-THPS2 21 22 TCBIAS (NC) 23 24 APPD1 DSW-ADU 25 26 APPD2 27 /DGS 28 AINPD 29 GND2 30 GND2 31 (NC) 32 DSW-L

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

DRAWER 1 DSW-L /ADUM2/A 2 /ADUM2A 3 /ADUM2B 4 /ADUM2/B 5 +5V-APPD1 6 +5V-APPD2 7 +5V-PFD2 8 +5V-DSW 9 +5V-AINPD 10 11 (NC) /ADUM1/A 12 /ADUM1A 13 /ADUM1B 14 /ADUM1/B 15 16 +24V1 +24V(DSW) 17 18 PFD2 /CFM-ADU 19 20 THPS2 21 TURM /TCB-PWM 22 23 /TCBIAS +5V-THPS2 24 25 GND2 26 GND2 27 APPD1 28 APPD2 29 AINPD DSW-ADU 30 31 /DGS 32 +24V2

SMR-12V-N/SMP-12V-NC 1 +5V-PFD2 1 2 PFD2 2 3 +5V-THPS2 3 4 THPS2 4 5 /TCB-PWM 5 6 6 /TCBIAS 7 DSW-L 7 8 DSW-L 8 9 GND2 9 10 TURM 10 11 +24V1 11 12 /CFM-ADU 12

QR/P4-32S-C(01)/QR/P4-32P-C(01)

PHR-3 1 +5V-PFD2 2 GND2 3 PFD2 179228-3 1 THPS2 2 GND2 3 +5V-THPS2 PHR-2 1 TURM 2 GND2

1 2 3 4 5 6

B6B-PH-K-S DSW-L DSW-L /TCBIAS /TCB-PWM GND2 F-GND

TB PWB

SRA-21T-4

SRA-21T-4 SMR-06V-N/SMP-06V-NC 1 /ADUM2/A 1 2 /ADUM2A 2 3 /ADUM2B 3 4 /ADUM2/B 4 5 5 +24V2 6 6 +24V2

SMR-06V-N/SMP-06V-NC 1 /ADUM1/A 1 2 /ADUM1A 2 3 /ADUM1B 3 4 /ADUM1/B 4 5 +24V2 5 6 +24V2 6 179228-3 1 AINPD 2 GND2 3 +5V-AINPD

PHNR-03-H+BU03P-TR-P-H 3 AINPD 1 2 GND2 2 1 +5V-AINPD 3

179228-3 1 DSW-ADU 2 GND2 3 +5V-DSWD PHNR-02-H+BU02P-TR-P-H

LEFT DOOR UNIT

MX-M700N DUPLEX SECTION H – 1

FPS-187 Bias

2 +24V1 1 DGS

1 2

AINPD

Signal name AINPD

Duplex (ADU) paper entry detector

APPD1

APPD1

Duplex (ADU) paper detector 1

Duplex (ADU) paper entry detection, detection of paper exit to finisher Duplex (ADU) upstream paper detection

APPD2

APPD2

Duplex (ADU) paper detector 2

Duplex (ADU) midstream paper detection

DSW-ADU

DSW-ADU

Duplex (ADU) cover open/close detection

PFD2

PFD2

Duplex (ADU) cover open/close detector Paper detector 2

THPS2

THPS2

1

1

Transfer belt /separation home position sensor 2 Duplex (ADU) motor 1

2

2

Duplex (ADU) motor 2

Drives the paper transport roller 2 and the paper transport roller 19 Drives the paper transport roller 20 and 21

TURM

TURM

Transfer separation motor

Drives and separates the transfer belt

DC brush motor

DGS

DGS

Paper exit gate solenoid

Drives the paper exit gate

DSW-L

DSW-L

Left door open/close detector

Left door open/close detection

Electromagnetic solenoid Micro switch

Code

No. 1 2 3 4

Name

Name Transport roller 21 (Drive) Transport roller 20 (Drive) Transport roller 19 (Drive) Paper exit roller 2 (Drive)

Function/Operation

Paper detection (Left door unit) from duplex (ADU)/Paper feed tray 1, 3, 4 Transfer belt separation home position detection 2

Type

NOTE

Transmission type Transmission type Transmission type Transmission type Transmission type Transmission type Stepping motor Stepping motor

Paper transport system sensor Paper transport system sensor Paper transport system sensor Door switch Paper transport system sensor Other sensor, switch High speed only Selection of Normal speed/ High speed The transfer belt is pressed on the OPC drum only during printing.

Door switch

Function/Operation Transports paper from the transport roller 20 to the transport roller 15 Transports paper from the transport roller 19 to the transport roller 21 Transports paper from the transport roller 2 to the transport roller 20 Discharges paper. / Transports paper to the duplex (ADU) section

2. Operational descriptions A. Outline When duplex print is selected, paper one surface of which was printed is switched back to feed to the duplex section to make duplex print.

B. Paper transport operation in duplex print (1) 1)

Switchback operation and transport to the reverse section

POM1

The paper transported from the fusing section is sent to the paper exit roller 1 (which is driven by the paper exit motor 2 (POM2)) with the transport roller 16 (which is driven by the paper exit motor 1 (POM1)). At this time, paper is ed under the paper exit guide. After paper ing, the paper exit gate guide falls down by its own weight.

MX-M700N DUPLEX SECTION H – 2

POM2 POD1

2)

When the specified time has ed from detection of the paper lead edge by POD1 (paper exit detection from fusing), POM2 rotates in the normal direction, then rotates in the reverse direction in the specified time. (The rotation time differs depending on the paper size.)

3)

When POM2 rotates reversely, paper is transported to the reverse section.

5)

POM2 stops after ing the specified time from detection the paper lead edge by AINPD (duplex paper entry detection). It rotation is changed from reverse direction to normal direction to transport the next paper.

RRC

At that time, paper is ed over the paper exit gate guide which fell down by it own weight.

439mS

POM1 120mS

POM2

166mS 485mS 25mS

572mS

DGS POM1

37mS 102mS

ADUM1 ADUM2

50mS

168mS

POD1 POD2 AINPD APPD1

POM2

APPD2

(2)

Paper transport speed in duplex print

The transport speed in duplex print is changed to the high speed (800mm/sec) to increase the job speed in some positions of paper. The transport speed is changed to the high speed in the Following positions:

4)

When the specified time has ed from reverse rotation of POM2, DGS (paper exit guide) turns on for a certain time and paper is sent to the reverse section.

1)

From when the paper rear edge es the fusing section to when switchback opration is started.

2)

From when switchback operation is started to when a certain amount of paper is transported after ing APPD1 (Paper detection sensor in upstream of duplex).

3)

After that, paper is stopped at the duplex paper feed position and fed to the machine again. (The paper feed speed to the machine is 335mm/sec)

1 DGS

POM2

MX-M700N DUPLEX SECTION H – 3

3. Disassembly and assembly

(1)

A. Duplex section

1)

No. (1)

Unit Left door unit

Mainte nance

No.

Parts

a b c d e f g h i j k

ADU opening/closing door Paper exit roller 2 Transport roller 19 Transport roller 20 Transport roller 21 Duplex motor 1 Duplex motor 2 Paper exit gate solenoid Duplex paper entry detector Duplex paper detector 1 Left door transport paper guide R unit Duplex paper detector 2 Paper detector 2 Transfer high voltage transformer Transfer separation motor Transfer belt separation home position sensor Switchback gate Paper exit gate Left door open/close detector Duplex cover open/close detector Fusing discharge brush Reversing discharge brush

l m n o p q r s t u v

(1)-r (1)-u (1)-v (1)-c

(1)-b

✕{ ✕{ ✕{ ✕{

2 1

2)

Remove the front cabinet.

3)

Remove the fixing screw.

✕ ✕

(1)-f

(1)-t (1)-v (1)-q (1)-i

Left door unit Pull out the left door.

(1)-h (1)-s

(1)

(1)-j

(1)-g (1)-o (1)-k (1)-m (1)-p (1)-d (1)-e

(1)-a

(1)-l

(1)-n

MX-M700N DUPLEX SECTION H – 4

4)

b. Paper exit roller 2

Remove the left door unit.

1)

Pull out the left door.

2)

Remove the ADU opening/closing door.

3)

Remove the ADU paper exit upper paper guide.

4)

Remove the ADU brake collar.

5)

Remove the E-ring to remove the transport roller 2 assembly.

6)

Remove the E-ring to remove the bearing, pulley, gear and pin from the paper exit roller.

a. ADU opening/closing door 1)

Pull out the left door.

2)

Remove the stopper section plastic E-ring.

c. Transport roller 19 d. Transport roller 20 e. Transport roller 21 3)

Remove the stopper from the fulcrum shaft to remove the opening/closing door in the arrowed direction.

1)

Pull out the left door.

2)

Remove the ADU opening/closing door.

3)

Remove the left door cabinet F.

4)

Remove the left door cabinet R.

MX-M700N DUPLEX SECTION H – 5

5)

Remove the front belt collar.

6)

Remove the E-ring to remove the transport roller 19 assembly.

11) Remove the E-ring and lift up the switching lever to remove the transport roller 20 assembly.

12) Remove the bearing, pulley, gear and pin from the transport roller 20.

7)

Remove the bearing, pulley, gear and pin from the transport roller 19.

8)

Remove the rear belt collar.

9)

Remove the ground plate.

10) Remove the belt.

13) Remove the U-turn paper guide.

14) Apply the bearing attachment plate to remove transport roller 21.

MX-M700N DUPLEX SECTION H – 6

15) Remove the bearing, pulley, gear and pin from the transport roller 21.

3)

Remove the duplex motor 2.

h. Paper exit gate solenoid f. Duplex motor 1 1)

Pull out the left door.

2)

Remove the cover.

3)

Remove the duplex motor 1.

1)

Pull out the left door.

2)

Remove the cover.

3)

Remove the paper exit gate solenoid.

g. Duplex motor 2 1)

Pull out the left door.

i. Duplex paper entry detector

2)

Remove the cover.

1)

Pull out the left door.

2)

Remove the paper guide unit.

MX-M700N DUPLEX SECTION H – 7

3)

Remove the follower roller unit.

4)

Remove the duplex paper entry detector.

3)

Remove the duplex paper detector 1.

k. Left door transport paper guide R unit.

j. Duplex paper detector 1 1)

Pull out the left door.

2)

Remove the cover.

1)

Pull out the left door.

2)

Remove the transfer unit.

3)

Remove the cover, and remove the connector, the snap band, and the earth terminal.

MX-M700N DUPLEX SECTION H – 8

4)

Remove the left door transport paper guide R unit.

n. Transfer high voltage transformer 1)

Pull out the left door.

2)

Remove the left door transport paper guide R unit.

3)

Remove the transfer high voltage transformer.

l. Duplex paper detector 2 1)

Pull out the left door.

2)

Remove the left door transport paper guide R unit.

3)

Remove the duplex paper detector 2.

o. Transfer separation motor 1)

Pull out the left door.

2)

Remove the left door transport paper guide R unit.

3)

Remove the transfer high voltage transformer.

4)

Remove the PWB holder.

m. Paper detector 2 1)

Pull out the left door.

2)

Remove the left door transport paper guide R unit.

3)

Remove the paper detector 2.

MX-M700N DUPLEX SECTION H – 9

5)

6)

q. Switchback gate

Remove the transfer separation unit.

1)

Pull out the left door.

2)

Remove the paper guide unit.

3)

Remove the paper exit gate.

Remove the transfer separation motor.

p. Transfer belt separation home position sensor 1)

Pull out the left door.

2)

Remove the left door transport paper guide R unit.

3)

Remove the transfer belt separation home position sensor.

r. Paper exit gate 1)

Pull out the left door.

2)

Remove the paper guide unit. Open the door, and remove the cabinets.

MX-M700N DUPLEX SECTION H – 10

3)

t. Duplex cover open/close detector

Remove the switchback gate.

1)

Pull out the left door.

2)

Open the door, and remove the cover.

3)

Remove the duplex cover open/close detector.

s. Left door open/close detector 1)

Pull out the left door.

2)

Remove the cover.

u. Fusing discharge brush

3)

Remove the left door transport paper guide R unit.

4)

Remove the left door open/close detector.

1)

Pull out the left door.

2)

Remove the fusing discharge brush.

* Attach the fusing discharge brush so that it is fit with the rear end.

MX-M700N DUPLEX SECTION H – 11

v. Reversing discharge brush 1)

Pull out the left door.

2)

Remove the switchback gate.

3)

Remove the reversing discharge bursh.

* Attach the reverse discharge brush so that it is fit with the rib inside and the parting line.

4. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Duplex

No. 1 2 3

Part name Transport rollers Transport paper guides Discharge brush

✕ { ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ { ✕

{ { ✕

{ { ✕

{ { ✕

{ { ✕

{ { ✕

{ { ✕

{ { ✕

3 3 1

1 2

1

1

MX-M700N DUPLEX SECTION H – 12

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

MX-M700N [i] LSU SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

CN-8

MFP CONTROL PWB

CN-8

CN-6

CN-6

PCU PWB CN-22 B30B-PHDSS-B 1 GND2 2 +5VLD 3 GND2 4 GND2 5 /READY 6 /PMCLK 7 /START 8 +24V1 9 (NC) 10 +24V1 11 +5V2 GND2 12 13 +5V2 14 GND2 15 TEST 16 TEST2 17 VRB 18 GND2 19 TEST3 20 GND2 21 VIDEO 22 GND2 23 /VIDEO 24 GND2 25 LSU S/H 26 GND2 27 /LDON 28 GND2 29 /SYNC GND2 30

MOTHER PWB

SMP-18V-NC/SMR-18V-N 1 1 GND2 2 2 +5VLD 3 3 GND2 4 GND2 4 5 5 /READY 6 6 /PMCLK 7 7 /START 8 8 +24V1 9 9 (NC) 10 +24V1 10 11 11 +5V2 12 GND2 12 13 +5V2 13 14 GND2 14 15 TEST 15 16 TEST2 16 17 VRB 17 18 GND2 18 1 2 3 4 5 6 7 8 9 10 11 12

TEST3 GND2 /VIDEO VIDEO GND2 GND2 LSU S/H GND2 /LDON GND2 /SYNC GND2

1 2 3 4 5 6 7 8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

CN-2 B30B-PHDSS-B GND2 +5VLD GND2 GND2 /READY /PMCLK /START +24V1 /BRAKE +24V1 +5V2 GND2 +5V2 GND2 TEST TEST2 VRB GND2 TEST3 GND2 /VIDEO GND2 VIDEO GND2 LSU S/H GND2 /LDON GND2 /SYNC GND2

CN-1 B6B-PH-K-S /BRAKE /PMCLK /READY /START GND2 +24V1

1 2 3 4 5 6

LD PWB CN-3 B4B-PH-K-S GND2 /SYNC GND2 +5V2

1 2 3 4

SMP-12V-NC/SMR-12V-N

BD

LSU UNIT

3 10 4

2

6

1

7 9 8

PGM 5

Code PGM BD

No. 1 2 3 4 5 6 7 8 9 10

Signal name PGM

Name Control signal Control signal Control signal Control signal Control signal Control signal

Type

Polygon mirror (motor) BD PWB

Name Laser control PWB Cylindrical lens Incidence reflection mirror No. 1 mirror f T lens 1 f T lens 2 BD mirror No. 2 mirror Plane lens Collective lens for BD No.

RW RW RW RW RW RW

Name

Function/Operation

NOTE

Reflects laser beams at the constant rotation speed Detects the laser scan start timing This device is used to detect a laser trouble Function/Operation Controls laser beam flashing and the output value Converges laser beams to focus Assures the optical path for laser beams Assures the optical path for laser beams Deflects laser beams so that the laser scan speeds on the both ends of the drum and that at the center of the drum are the same Assures the optical path for laser beams to the BD PWB Assures the optical path for laser beams Converges laser beams to focus Converges laser beams on to the BD PWB Code +5VLD /READY /PMCLK /START /VIDEO /SYNC

Function/Operation 5V power for laser diode Polygon mirror motor READY signal ("L" in the constant speed rotation) Clock signal for driving the polygon mirror motor Polygon mirror motor drive start signal VIDEO (Image signal) Sync signal (SYNC) from BD, sync signal for 1 line

MX-M700N LSU SECTION i – 1

2. Operational descriptions

3. Disassembly and assembly

A. Outline

A. Laser scan unit (LSU)

This section performs the following operations. Image data sent from the MFP (image process circuit) through the mother board and PCU are converted into laser beams to radiate onto the drum surface.

No. 1

Unit LSU

(1) LSU

[Laser optical path]

(1)

* This unit must not be disassembled in the market.

1)

Pull out the multi paper feed tray, and remove the manual paper feed cover F.

2)

Pushing the lower part, remove the right cabinet center.

B. Polygon mirror motor Model 55/62ppm 70ppm

Number of mirror surface 14 surfaces

Rotating speed 34000 rpm

14 surfaces

40000 rpm

Bearing AIR

Remarks Superior in silence

AIR

The number of mirror surfaces and the motor RPM are reduced to reduce noises and increase reliability.

C. Outline of LSU specifications Effective scan width : 297 mm Resolution : 600 dpi Beam diameter : Main scan = 60 to 85 Pm Sub scan = 75 to 110 Pm Laser power : 55/62ppm: 0.385 r 0.04mW 70ppm: 0.480 r 0.04mW Laser power : 770 to 795 nm

MX-M700N LSU SECTION i – 2

3)

Disconnect the connector, and remove the process cooling fan unit.

4)

Disconnect the connectors to remove the LSU unit.

MX-M700N LSU SECTION i – 3

MX-M700N [J] PHOTOCONDUCTOR SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram A. OPC drum Section

AC PWB

PCU PWB

CN-5 B16B-PADSS-1 +38V 10 +38V 11 +38V 12 GND1 14 GND1 15 GND1 16 CN-6 B18B-PHDSS-B GND2 1 GND2 2 +5V2 3 +5V2 4 /DM 5 /DVM 6 DMCLK 7 DVMCLK 8 DM-T 9 DVM-T 10 GND2 11 +5V2 12 /FUM 13 FUMCLK 14 FUM-T 15 +24V1 16 /VFM-BKR 17 GND2 18

B2PS-VH 1 +38V 2 GND1 S5B-PH-K-S 1 GND2 2 +5V2 3 /DVM 4 DVMCLK 5 DVM-T

PROCESS UNIT SMR-03V-B/SMP-03V-BC 1 1 +12V2 2 PCS 2 3 PCS-LED 3 SMR-03V-B/SMP-03V-BC 1 +12V2 1 2 DMS 2 3 DMS-LED 3 DRAWER TSDR-20V-K/TSDP-20V-K 1 PCS-LED 1 2 PCS 2 3 +12V2 3 4 DMS-LED 4 5 DMS 5 6 +12V2 6 7 +24V-DL 7 8 /DL 8 9 +24V1 9 10 /PTDL 10 11 (NC) 11 12 +24V1 12 13 /PSPS 13 14 TH-CL 14 15 GND2 15 16 (NC) 16 17 (NC) 17 18 (NC) 18 19 (NC) 19 20 GND2 20

CN-8 B20B-PHDSS-B PCS-LED 1 DMS-LED 2 PCS 3 DMS 4 +12V2 5 +12V2 6 +24V-DL 7 +24V1 8 /DL 9 /PTDL 10 +24V1 11 TH-CL 12 /PSPS 13 GND2 14 +5V2 15 TLS 16 HUS-TC 17 GND2 18 GND2 19 /PWM-RSV1 20

PHR-3 1 +24V-DL 2 (NC) 3 /DL

DM

SMP-02V-BC/SMR-02V-B 1 1 +24V1 2 2 /PSPS S4B-PH-K-S 1 (NC) 2 (NC) 3 TH-CL 4 GND2

7 PSPS

SRA-01T-3.2

SRA-01T-3.2

TH-CL DL PCS DMS

8

6 4 3 2 1

5 9

DMS PCS TH-CL

Signal name DMS PCS TH-CL

DM PSPS DL

Code

No. 1 2 3 4 5 6 7 8 9

Name

Function/Operation

Type

OPC drum mark detection Detection of density of toner patch on the OPC drum OPC drum cleaner peripheral temperature detection

Reflection type Reflection type Thermistor

DM

OPC drum marking sensor signal Image density sensor OPC drum cleaner temperature sensor OPC drum motor

Drives the OPC drum and the transfer section

PSPS DL

Drum separation pawl solenoid Discharge lamp

Drives the OPC drum separation pawl Discharges electric charges on the OPC drum

DC brushless motor Solenoid Lamp

Name OPC drum Cleaning blade CL brush roller Sub blade (Cleaning seal) Side seal F/R Drum separation pawl Separation pawl oscillation shaft Waste toner transport screw Waste toner transport pipe

NOTE Analog detector Analog detector Analog detector

Function/Operation Forms electrostatic latent images by laser beams Cleans remaining toner on the OPC drum Cleans remaining toner on the OPC drum Prevent against toner leakage from the cleaner section Prevents against toner dispersion Separates paper from the drum Moves in the front and rear frame direction to install the separation pawl Transports toner from the cleaner unit to the waste toner transport pipe Transports toner from the cleaner unit to the waste toner box in the toner cartridge front section

MX-M700N PHOTOCONDUCTOR SECTION J – 1

B. Main charger section

PCU PWB PS-187(RD) MHV PS-187(YL) GB FPS-187(WH) THV PS-187(GR) Bias

HV

CN-15 B34B-PHDSS-B 1 DSW-F 2 (NC) 3 GND2 4 GND2 5 /GBPWM 6 /MHVREM 7 MHV-T 8 /THV+PWM 9 THV+REM 10 /CHV-PWM 11 /CHV-REM 12 /CHVAWM 13 /CHVACREM 14 /DVPWM 15 /DVREM 16 HVREM 17 +24V1 18 (NC) 19 GND2

CN-1 B16B-PH-K-S DSW-F 1 GND2 2 GND2 3 /GBPWM 4 /MHVREM 5 MHV-T 6 /THV+PWM 7 THV+REM 8 /CHV-PWM 9 /CHV-REM 10 /CHVAWM 11 /CHVACREM 12 /DVPWM 13 /DVREM 14 HVREM 15 +24V1 16

2

2

1

No. 1 2

Name Screen grid Sawtooth plate

Function/Operation Charges the OPC drum evenly / Charges the OPC drum Charges the OPC drum

MX-M700N PHOTOCONDUCTOR SECTION J – 2

1

2. Operational descriptions A. Outline

3)

In this section, laser beams are radiated to the OPC drum surface which was negatively charged, making electrostatic latent images.

After transfer operation, remaining toner is removed by the cleaning blade.

B. Description The OPC drum surface is negatively charged by the main charger. The laser beam images are radiated to the OPC drum surface by the laser unit to form latent electrostatic images. 1)

Drum

The OPC drum surface is negatively charged by the main charger.

Main corona unit

High voltage unit

Screen grid

Toner removed from the OPC drum surface is transported to the waste toner section in the toner cartridge by the waste toner transport screw.

CTL CGL

4)

Aluminum layer

OPC drum

The whole surface of the OPC drum is discharged.

Lamp

The main charger grid is provided with the screen grid. The OPC drum is charged at a voltage virtually same as the voltage applied to the screen grid. 2)

LED lights are radiated to the OPC drum surface by the laser unit to form latent electrostatic images.

CLT CGL layer Auminum

CLT CGL layer Auminum

By radiating the discharge lamp light to the discharge lens, light is radiated through the lens to the OPC drum surface. When the discharge lamp light is radiated to the OPC drum CGL, positive and negative charges are generated.

LED lights

Positive charges generated in CGL are attracted to the negative charges on the OPC drum surface. On the other hand, negative charges are attracted to the positive charges in the aluminum layer of the OPC drum.

OPC drum OPC drum

CTL CGL layer Aluminum

When laser lights are radiated to the OPC drum CGL, negative and positive charges are generated.

Therefore, positive and negative charges are balanced out on the OPC drum surface and in the aluminum layer, reducing positive and negative charged to decrease the surface voltage of the OPC drum.

Drum

Positive charges generated in CGL are attracted to the negative charges on the OPC drum surface. On the other hand, negative charges are attracted to the positive charges in the OPC drum aluminum layer. Therefore, positive charges and negative charges are balanced out on the OPC drum and in the aluminum layer, reducing positive and negative charges to decrease the OPC drum surface voltage. Electric charges remain at a position where LED lights are not radiated. As a result, latent electrostatic images are formed on the OPC drum surface.

C. Main charger The OPC drum surface is negatively charged in this section. MX-M700N PHOTOCONDUCTOR SECTION J – 3

3. Disassembly and assembly (1) Process unit

A. OPC drum Section No. (1)

Unit Process unit

No. a b c d e f g h i j k l m

Parts OPC drum Separation pawl Cleaning blade Toner reception seal Side seal F/R Side seal R base sheet Cleaning brush Process adsorption plate Drum separation pawl solenoid OPC drum cleaner temperature sensor Discharge lamp Image density sensor OPC drum marking sensor

1)

Open the front door.

2)

Open the process cover.

Mainte nance ✕▲ ✕▲ ✕▲ ✕▲ ✕▲ ▲

(1)-j (1)-i (1)-l

(1)-m

(1)-h (1)-k (1)-a (1)-g (1)

(1)-b

(1)-e

(1)-d (1)-e (1)-f

(1)-c

3)

Open the left door.

4)

Remove the MC charger unit.

5)

Remove the blue screw.

6)

Unfix the drum to remove the bearing.

7)

Pull out the process unit by clasping the bolt head.

MX-M700N PHOTOCONDUCTOR SECTION J – 4

a. OPC drum

b. Separation pawl

1)

1)

Disconnect the connecters.

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the resin E-ring.

3)

Remove the separation pawl.

c. Cleaning blade 1)

2)

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the cover.

3)

Remove the cleaning blade.

Remove the blue screw to open the lower frame.

3)

Gently remove the drum, guide and all.

4)

Remove the guide. * The OPC layer of a certain area of the OPC drum may break off due to rotational friction. The OPC layer break-off generated in the area shown below will not affect print images. Therefore, the drum can be used without replacement. d. Toner reception seal 1)

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the toner receiving seal.

12mm 14mm

* When replacing the OPC drum, apply friction-reducing powder (UKOG-0309FCZZ) to all over the drum (F and R) in order to reduce friction and membrane decrease of the OPC layer on both sides of the OPC drum. (Use PARTEL (UKOG-0311FCZZ).)

MX-M700N PHOTOCONDUCTOR SECTION J – 5

e. Side seal F/R

h. Process adsorption plate

f. Side seal R base sheet

1)

1)

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the side seal R base sheet.

3)

Attach the side seal R base sheet to the specified position. Attach the side seals F/R to the specified positions.

Remove the cover to remove the adsorption plate.

i. Drum separation pawl solenoid 1)

Disconnect the connector, and remove the harness guide unit.

2)

Remove the drum separation pawl solenoid.

* Clean and remove toner and dust from the attachment section with alcohol. * When replacing the side seals F/R, apply friction-reducing powder (UKOG-0309FCZZ) to all over the side seals F/R in order to reduce friction and membrane decrease of the OPC layer on both sides of the OPC drum. (Use PARTEL (UKOG-0311FCZZ).)

g. Brush roller 1)

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the toner receiving seal.

3)

Remove the blue screw to remove the lever.

4)

Remove the brush roller.

MX-M700N PHOTOCONDUCTOR SECTION J – 6

j. OPC drum cleaner temperature sensor

l. Image density sensor

1)

1)

Remove the upper cover. (See “j. OPC drum cleaner temperature sensor”)

2)

Remove the connecter.

3)

Remove the OPC drum. (See “a. OPC drum”)

4)

Remove the image density sensor.

2)

Remove the upper cover.

Remove the OPC drum cleaner temperature sensor.

k. Discharge lamp 1) 2)

m. OPC drum marking sensor

Remove the upper cover. (See “j. OPC drum cleaner temperature sensor”) Remove the discharge lamp.

1)

Remove the OPC drum. (See “a. OPC drum”)

2)

Remove the OPC drum marking sensor. * Execute cleaning.

* Be careful not to break the pawl when fixing.

A

MX-M700N PHOTOCONDUCTOR SECTION J – 7

B. Main charger section No. (1)

Unit Main charger unit

No. a b c

2)

Remove the screen grid from the claw.

Parts Screen grid Sawtooth plate MC cleaner

(1) (1)-b

(1)-c

b. Sawtooth plate 1)

Remove the blue screw.

2)

Lifting one end up, slide off the saw blade holder.

(1)-a

(1)

Main charger unit

1)

Open the front door.

2)

Loosen the blue screw.

3)

Remove the main charger unit.

c. MC cleaner 1)

Remove the screen grid. (See “a. Screen grid”)

2)

Remove the saw teeth plate. (See “b. Saw teeth plate”)

3)

Remove the MC cleaner.

a. Screen grid 1)

Loosen the screw.

MX-M700N PHOTOCONDUCTOR SECTION J – 8

4. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.) 250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕ ✕

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

✕ ✕

▲ ▲ ✕ { ▲ ▲

▲ ▲ ▲ { ▲ ▲

▲ ▲ ✕ { ▲ ▲

▲ ▲ ▲ { ▲ ▲

▲ ▲ ✕ { ▲ ▲

▲ ▲ ▲ { ▲ ▲

▲ ▲ ✕ { ▲ ▲

▲ ▲ ▲ { ▲ ▲

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Drum peripheral section

No. 1 2

3 4 5 6 7 8

Part name Drum Cleaning blade

Cleaning brush roller Toner reception seal Side seal Drum separation pawl Sawtooth plate Screen grid

✕ { ✕

3

1

5

6

4

2

5 7

MX-M700N PHOTOCONDUCTOR SECTION J – 9

8

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

After installation, the used product for one year is recommendable to exchange. (P/G No.: [43]-5) (P/G No.: [43]-29) (P/G No.: [43]-11) (P/G No.: [43]-33, [43]-35) (P/G No.: [42]-33) (P/G No.: [39]-7) (P/G No.: [39]-1)

MX-M700N

[K] TONER SUPPLY SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

TM1X

8 7 TM2X

1 TFSD

2 3

CRUM

6

5

TONER HOPPER PHR-4 +24V1 1 TFSD 2 (NC) 3 GND2 4

4

SMR-02V-N/SMP-02V-NC 1 TM1a 1 2 TM1b 2 DRAWER TSR-04V-K GND2 1 +5V2 2 CRUCLK 3 CRUSDA 4

8

7

2

TFSD

TSDP-12V-K/TSDR-12V-K 1 +24V1 1 2 TFSD 2 3 GND2 3 4 (NC) 4 5 TM1a 5 6 TM1b 6 7 (NC) 7 8 GND2 8 9 +5V2 9 10 CRUCLK 10 11 CRUSDA 11 12 GND2 12

SRA-01T-3.2

SRA-01T-3.2

CN-11 B12B-PHDSS-B 1 TM1a 2 GND2 3 TM1b 4 +5V2 5 TM2a 6 CRUCLK 7 TM2b 8 CRUSDA 9 +24V1 10 GND2 11 TFSD 12 TNCA

PCU PWB

1 SMR-02V-N/SMP-02V-NC 1 1 TM2a 2 2 TM2b

TM1X

Signal name TM1X

Toner motor 1

TM2X

TM2X

Toner motor 2

TFSD CRUM

TFSD

Toner sensor CRUM lap

Code

No. 1 2 3 4 5 6 7 8

Name

Name TH shutter Toner mixing roller Waste toner box drive gear Waste toner transport plate Waste toner transport plate Waste toner shutter TH shaft Toner supply roller

Function/Operation

Type

Transports toner in the toner hopper to the developing unit/Transports waste toner to the waste toner section Transports toner in the toner bottle to the toner hopper Toner hopper remaining quantity detection Stores the toner bottle information

Synchronous motor Synchronous motor Magnetic sensor

NOTE

Function/Operation Serves as a shutter to supply toner from the toner bottle unit to the toner hopper. When a toner bottle unit is installed, the shutter opens. Mixes toner in the toner hopper. Drives the waste toner transport parts. Remains toner evenly in the waste toner box. Remains toner evenly in the waste toner box. Serves as a shutter to receive waste toner from the process unit. Toner supply roller to the toner unit section. Toner supply roller to the developing unit section.

MX-M700N TONER SUPPLY SECTION K – 1

2. Operational descriptions

C. Operation

A. Outline Adoption of the rotating toner bottle enables large capacity with a compact toner bottle size. When the remaining toner detection sensor in the toner hopper unit detects no toner, the toner bottle turns to supply toner to the toner hopper. Following supply, since the sensor detects full or empty status inside the toner hopper based on a standard quantity of approximately 150 g of toner, even if the toner cartridge becomes empty, copying is not immediately suspended because toner inside the toner hopper is used (approximately 5K/6% print duty documents). Toner filling amount 1,430g / 1,650g

Life with 6% print duty k]documents 72,000 sheets / 83,000 sheets

B. Composition

The toner remaining quantity sensor in the toner hopper detects the toner remaining quantity by the toner stirring roller rotation. When there is little toner, the toner bottle rotating motor of the machine is rotated. The toner bottle rotates at 4.2rpm. Toner of about 54g is supplied to the toner hopper for every rotation. When toner full is not detected after detecting the state with little toner for a certain period (4min), the toner cartridge is judged as empty, and the display to urge toner cartridge replace is shown on the operation . * When the power is turned on for toner hopper replacement or cleaning, the toner cartridge replacement display is shown though toner is not accumulated enough in the toner hopper. In such a case, turn off/on the power again.

Shutter lock pawl TB holder upper Toner bottle

TB shutter TB holder lower CRUM TH shutter

TB holder upper Heat seal Toner bottle

CRUM

TB holder lower

The toner cartridge is composed of the toner bottle with toner filled in it, the TB holder lower which holds the toner bottle and to which the CRUM and the waste toner box assembly are attached, and the TG holder upper. The TB holder lower is attached to the TB shutter. When inserting it to the machine, the toner hopper rib releases the shutter lock pawl, and opens in linkage with the TH shutter. When removing the toner cartridge from the machine, the TB shutter closes. * The toner discharge port of the toner bottle is sealed by the heat seal. Do not rotate the toner bottle manually, or the heat seal is dismantled and toner is discharged from the TB shutter port.

MX-M700N TONER SUPPLY SECTION K – 2

3. Disassembly and assembly

4)

Clean the shutter area.

A. Toner hopper and toner bottle section No. (1) (2)

Unit Toner bottle unit Toner hopper unit

(3)

Others

No. a b a

Parts Toner sensor Toner motor 1 Toner motor 2

(2)-b (2)

(3)-a

(2)-a

a. Toner sensor 1)

Remove the toner hopper unit. (See “(2) Toner hopper unit”)

2)

Remove the cover.

3)

Remove the toner sensor.

(1)

(1)

Toner bottle unit

1)

Open the front door.

2)

Remove the toner bottle.

(2)

Toner hopper unit

1)

Remove the toner bottle unit. (See “(1) Toner bottle unit”)

2)

Open the process cover.

b. Toner motor 1

3)

Remove the toner hopper unit.

1)

Remove the toner hopper unit. (See “(2) Toner hopper unit”)

2)

Remove the toner motor 1.

MX-M700N TONER SUPPLY SECTION K – 3

(3)

Others

5)

Remove the toner motor 2.

a. Toner motor 2 1)

Remove the toner bottle. (See “(1) Toner bottle unit”)

2)

Remove the toner hopper unit. (See “(2) Toner hopper unit”)

3)

While pressing the bottle coupling, turn it 90 degrees to the left and remove it. Remove the spring.

4)

Disconnect the connector, and remove the toner motor unit.

4. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Developing section

No. 1

2

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

{

Assembly when installing/ Replacement by when empty Clean the shutter area.

Part name Toner bottle

Toner hopper

{

{

{

{

{

{

{

{

2

1

MX-M700N TONER SUPPLY SECTION K – 4

MX-M700N

[L] DEVELOPING SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

1

2

3

5

CN-5 B16B-PADSS-1 10 +38V 11 +38V 12 +38V 14 GND1 15 GND1 16 GND1

DVM B2PS-VH +38V 1 GND1 2 S5B-PH-K-S GND2 1 +5V2 2 /DVM 3 DVMCLK 4 DVM-T 5

3

2

1

HUS-DV TH-DV

4 TCS

DEVELOPER UNIT 51021-0400 TSGOUT 1 +24V1 2 TCS 3 GND2 4

ZHR-4 +5V2 HUS-DV GND2 TH-DV

5

1 2 3 4

SRA-01T-3.2

DRAWER 1 DVCH1 1 2 DVCH2 2 3 DVCH3 3 4 DVCH4 4 5 +24V1 5 6 TCS 6 7 GND2 7 8 TSGOUT 8 9 (NC) 9 10 GND2 10 11 (NC) 11 12 +5V2 12 13 HUS-DV 13 14 GND2 14 15 TH-DV 15 16 (NC) 16 17 (NC) 17 18 (NC) 18 19 (NC) 19 20 DV-Bias 20 QR/P8-20S-C(01)/QR/P8-20P-C(01)

CN-6 B18B-PHDSS-B 1 GND2 2 GND2 3 +5V2 4 +5V2 5 /DM 6 /DVM 7 DMCLK 8 DVMCLK 9 DM-T 10 DVM-T 11 GND2 12 +5V2 13 /FUM 14 FUMCLK 15 FUM-T 16 +24V1 17 /VFM-BKR 18 GND2

CN-12 B30B-PHDSS-B 1 +24V1 2 +24V1 3 /T2PFC 4 /HPLS 5 +24V1 6 DVCH1 7 /HPFC 8 DVCH2 9 +24V1 10 DVCH3 11 /PSBC 12 DVCH4 13 +5V2 14 +24V1 15 PPD 16 TCS 17 GND2 18 GND2 19 +5V-MPRD1 20 TSGOUT 21 GND2 22 GND2 23 MPRD1 24 +5V2 25 +5V-MPRD2 26 HUS-DV 27 GND2 28 GND2 29 MPRD2 30 TH-DV

PS-187(GR) Bias

HUS-DV

Signal name HUS-DV

Developing humidity sensor

Developing section peripheral humidity detection

Humidity sensor

TCS

TCS

Toner density sensor

Toner density detection

Magnetic sensor

TH-DV

TH-DV

Developing humidity sensor

Developing section humidity detection

Thermistor

DVM

DVM

Developing motor

Drives the developing section.

DC brush-less motor

Bias

Bias

Developing bias

Developing bias

Code

No. 1 2 3 4 5

Name

Name Developing roller DV doctor Mixing roller DV earth plate AG roller

Function/Operation

Type

Function/Operation Forms magnetic brush with developer and put toner on the OPC drum. Keeps the height of the magnetic brush on the developing roller at a fixed level. Mixes developer (carrier and toner) and charges toner negatively. Earth plate for DV unit Mixes toner supplied from the toner hopper, and supplies toner to the DV box evenly.

MX-M700N DEVELOPING SECTION L – 1

AC PWB

PCU PWB CN-15 B34B-PHDSS-B /DVPWM 14 /DVREM 15 HVREM 16 17 +24V1

HV

NOTE Analog detector Analog detector Analog detector

CN1 DVREM

2. Operational descriptions

3. Disassembly and assembly

A. Outline

A. Developer tank section

In this section, toner is attached to electrostatic latent images formed by laser beams on the OPC drum, making visible images.

No.

B. Description

(1)

Unit

No.

Developing unit

a b c d e

Electrostatic latent images formed on the OPC drum by the LED (writing) unit (LED image light) are converted into visible images by toner.

layer Aluminum

(1)-d (1)-c

CGL CTL

(1)-b

Parts Developer DV seal MG holder F and R Side seal F and R Toner density sensor

(1)-a

(1)

Drum

(1)-d (1)-c

(1)-e

(1) 1)

Developing unit Take out the developing tank.

1

Cleaning mode

+150v

2

Developing mode

-500v

Toner in the developing unit is stirred by the mixing roller. When toner is stirred, it is negatively charged by mechanical friction. The developing bias voltage (negative) is applied to the developing roller. Negatively charged toner is attracted and attached to the area on the OPC drum where negative voltage is reduced by exposure. On the other hand, the negative voltage at an area where exposure is not made is higher than the developing bias voltage, and toner is not attached.

MX-M700N DEVELOPING SECTION L – 2

Mainte nance ▲ ▲ { ▲

a. Developer

c. MG holder F and R

1)

Take out the developing tank. (See “(1) Developing unit”)

1)

Take out the developing tank. (See “(1) Developing unit”)

2)

Remove the DV cover.

2)

Remove the DV cover. (See “a. Developer”)

3)

Remove the doctor cover.

4)

Remove the DV cover front.

5)

Remove the bias line and main pole position adjusting plate and screws.

6)

Remove the MG gear and screws.

3)

4)

Turning the MG roller, take out the old developer.

Insert the new developer.

b. DV seal 1)

Take out the developing tank. (See “(1) Developing unit”)

2)

Take out the old DV seal.

3)

Wipe the sealing face with alcohol.

4)

Affix the new DV seal at the reference position.

MX-M700N DEVELOPING SECTION L – 3

7)

Remove the side seals F and R.

d. Side seal F and R 1)

8)

Take out the developing tank. (See “(1) Developing unit”)

2)

Remove the doctor cover.

3)

Peel off the right and left side seals.

4)

Clean the peeled area.

5)

Peel off the new right and left seals from the mounting paper and affix in the designated positions.

Remove the MG roller unit.

e. Toner density sensor

9)

1)

Take out the developing tank. (See “(1) Developing unit”)

2)

Remove the DV cover. (See “a. Developer”)

3)

Remove the toner concentration sensor.

Remove the doctor attaching plate.

10) Remove the MG holders F and R.

MX-M700N DEVELOPING SECTION L – 4

4. Maintenance ✕: Check

{: Clean

▲: Replace

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust according to necessity.) 55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Developing section

No. 1 2 3 4 5

Part name Developer DV seal MG holder F/R DV side seal F DV side seal R

{

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

▲ ▲ { ▲ ▲

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

Supply when installing (P/G No.: [37]-5) (P/G No.: [36]-14) (P/G No.: [36]-13)

3 2 5 3 4 1

MX-M700N DEVELOPING SECTION L – 5

MX-M700N

[M] TRANSFER SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

DM

3 1 2 4 TURM

6

7

CN-15 B34B-PHDSS-B 7 MHV-T 8 /THV+PWM 9 THV+REM 10 /CHV-PWM

THPS2

HV FPS-187(WH) THV

1

3 5

2

CN-1 B16B-PH-K-S 6 MHV-T /THV+PWM 7 THV+REM 8 /CHV-PWM 9

CN-8 B20B-PHDSS-B 1 PCS-LED 2 DMS-LED 3 PCS 4 DMS 5 +12V2 6 +12V2 7 +24V-DL 8 +24V1 9 /DL 10 /PTDL 11 +24V1 12 TH-CL 13 /PSPS 14 GND2 15 +5V2 16 TLS 17 HUS-TC 18 GND2 19 GND2 20 (NC)

4 8

6 7 PCU PWB

CN-7 B32B-PHDSS-B +24V1 1 +24V1 2 3 /CFM-DV /RRC 4 GND2 5 (NC) 6 +24V1 7 +24V(DSW) 8 +5V-APPD1 9 PFD2 10 +5V-APPD2 11 THPS1 12 +5V-PFD2 13 THPS2 14 +5V-DSWD 15 TURM 16 +5V-AINPD 17 /SFM 18 +5V-THPS1 19 20 (NC) +5V-THPS2 21 22 (NC) /CFM-AM1 23 APPD1 24 DSWD 25 APPD2 26 27 /DGS 28 AINPD 29 GND2 30 GND2 31 (NC) 32 DSW-L

DRAWER 1 DSW-L /ADUM2/A 2 /ADUM2A 3 /ADUM2B 4 /ADUM2/B 5 +5V-APPD1 6 +5V-APPD2 7 +5V-PFD2 8 +5V-DSW 9 +5V-AINPD 10 11 SMR-12V-N/SMP-12V-NC (NC) 1 +5V-PFD2 1 /ADUM1/A 12 2 2 PFD2 /ADUM1A 13 179228-3 3 +5V-THPS2 3 /ADUM1B 14 1 THPS2 4 4 THPS2 /ADUM1/B 15 2 GND2 5 /TCB-PWM 5 16 +24V1 3 +5V-THPS2 6 +24V(DSW) 17 6 /TCBIAS 7 DSW-L 7 18 PFD2 8 DSW-L 8 /CFM-ADU 19 PHR-2 9 9 GND2 20 THPS2 10 10 TURM 1 TURM 21 TURM 11 11 +24V1 2 GND2 /TCB-PWM 22 12 /CFM-ADU 12 23 /TCBIAS +5V-THPS2 24 25 GND2 26 GND2 27 APPD1 FPS-187 B6B-PH-K-S 28 APPD2 Bias 1 DSW-L 29 AINPD 2 DSW-L DSW-ADU 30 /TCBIAS 3 31 /DGS 4 /TCB-PWM 32 +24V2 5 GND2 6 F-GND QR/P4-32S-C(01)/QR/P4-32P-C(01)

CN-6 B1v8B-PHDSS-B GND2 1 GND2 2 +5V2 3 +5V2 4 /DM 5 /DVM 6 DMCLK 7 DVMCLK 8 DM-T 9 DVM-T 10 GND2 11 +5V2 12 /FUM 13 FUMCLK 14 FUM-T 15 +24V1 16 /VFM-BKR 17 GND2 18

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

DM

OPC drum motor

Drives the OPC drum and the transfer section.

TURM

TURM

Transfer separation motor

Drives and separates the transfer belt.

THPS2

THPS2

Transfer belt separation home position detection 2

THV HUS-TC

THV HUS-TC

Transfer belt /separation home position sensor 2 Transfer high voltage Process humidity sensor

No. 1 2 3 4 5 6 7 8

Name

Name Transfer drive roller (Drive) Transfer cleaning roller Transfer belt Transfer tension roller Transfer belt discharge brush Transfer roller Transfer auxiliary roller (Idle) Transfer (TCCL) bias high voltage PWB

Function/Operation

High voltage for transfer Process section peripheral humidity detection

TB PWB

AC PWB

Signal name DM

Code

LEFT DOOR UNIT

S5B-PH-K-S 1 GND2 2 +5V2 3 /DM 4 DMCLK 5 DM-T B2PS-VH 1 +38V 2 GND1

CN-5 B16B-PADSS-1 +38V 10 +38V 11 +38V 12 GND1 14 GND1 15 GND1 16

Type DC brushless motor DC brush motor

Transmission type Humidity sensor

NOTE

The transfer belt is pressed on the OPC drum only during printing. Other sensor, switch Analog detector (Not used)

Function/Operation Drives the transfer belt. Cleans the transfer belt. Transfers toner images from the OPC drum to paper. Applies a proper tension to the transfer belt. Connects the transfer belt to the chassis ground. Applies a transfer voltage to the transfer belt. Helps to stretch the transfer belt. Generates a bias voltage for the transfer cleaning roller in cleaning or in the print mode.

MX-M700N TRANSFER SECTION M – 1

2. Operational descriptions A. Outline

After completion of the job, the applied voltage to the transfer cleaning roller is switched to negative, and toner is returned from the transfer cleaning roller to the transfer belt, and toner on the transfer belt is attracted to the drum and cleaned by the cleaning blade.

In this section, toner images on the OPC drum are transferred to paper.

B. Description 1)

Toner image transfer Toner images formed on the drum by the developing roller are transferred to paper by the transfer belt.

-2.0kv

Toner on the drum is negatively charged by stirring in the developing unit. By applying a positive voltage to the transfer roller, the transfer belt and paper on the transfer belt are positively charged to transfer negatively charged toner images to paper.

Cleaning roller cleaning mode

-2.0kv

2.0kv

Transfer belt cleaning mode

2.0kv

AC4.5kv -100v

Cleaning roller cleaning mode

Transfer mode 1.0 - 1.5kv (35μA) (55ppm, 62ppm) 2.0 - 2.5kv (40μA) (70ppm)

8

10 Ω

Cleaning timing:

AC4.5kv -100v

1.0~1.5kv 2.0~2.5kv (35μA) (40μA) 55ppm 70ppm 62ppm

After completion of the job, When warming-up, After canceling a jam, After execution of process control 8

10 Ω 3)

Transfer belt separation/ Transfer belt is separated by the transfer separation motor.

2)

The transfer belt is in with the drum except for the following cases.

Transfer belt cleaning During the job, a positive voltage is applied to the transfer cleaning roller so that negatively charged toner on the transfer belt is attracted to the cleaning roller. (The brush on the back of the transfer belt is provided for increasing the cleaning effect.)

The case that the transfer belt is separated from the drum except: * When executing process control (to prevent against breakage of toner patch on the drum) * When a jam occurs (Protection of the drum, left door open/ close) * When shipping (Protection of the drum. Separate with the simulation 6-1 (7).)

-2.0kv

2.0kv

MX-M700N TRANSFER SECTION M – 2

3. Disassembly and assembly A. Transfer section No. (1)

Unit

2)

No.

Transfer unit

a b c d e f g

Parts Transfer drive gear Transfer belt Transfer auxiliary roller Transfer roller Transfer roller collar Transfer cleaning roller Transfer cleaning brush

Loosen the blue screw and open the holder to remove the transfer unit.

Mainte nance ✕▲ {▲ ▲ ✕▲

(1)

(1)-g

a. Transfer drive gear 1)

Remove the transfer unit. (See “(1) Transfer unit”)

2)

Loosen the blue screw and unhook the hook lever in order to open the transfer belt unit in the arrowed direction.

3)

Remove the spring.

4)

Remove the transfer belt unit in the arrowed direction.

(1)-e (1)-a

(1)-f

(1)-b (1)-c (1)-d

(1)-e

(1) 1)

Transfer unit Open the left door unit.

2 1

MX-M700N TRANSFER SECTION M – 3

5)

Remove the ground .

b. Transfer belt

6)

Remove the blue screw to remove the roller fixing .

1)

Remove the transfer unit. (See “(1) Transfer unit”)

2)

Remove the transfer belt unit. (See “a. Transfer drive gear”)

3)

Pull out the transfer belt.

c. Transfer auxiliary roller d. Transfer roller 7)

Pull out the upper transfer roller unit from the transfer belt.

e. Transfer roller collar 1)

Remove the transfer unit. (See “(1) Transfer unit”)

2)

Remove the upper transfer roller unit.

3)

Remove the transfer belt. (See “b. Transfer belt”)

4)

Remove the transfer tension roller bearing to remove the transfer roller.

5)

Remove the E-ring to remove the transfer roller transfer roller collar.

(See “a. Transfer drive gear”)

8)

Remove the E-ring and screw to remove the transfer drive gear.

MX-M700N TRANSFER SECTION M – 4

f. Transfer cleaning roller

g. Transfer cleaning brush

1)

Remove the transfer unit. (See “(1) Transfer unit”)

1)

Remove the transfer unit. (See “(1) Transfer unit”)

2)

Remove the transfer belt unit. (See “a. Transfer drive gear”)

2)

Remove the upper transfer roller unit.

3)

Remove the E-ring to remove the transfer cleaning roller. 3)

Remove the transfer belt. (See “b. Transfer belt”)

4)

Remove the cleaning brush.

(See “a. Transfer drive gear”)

4. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Transfer section

No. 1 2 3 4 5 6

Part name Transfer drum gear Transfer belt Transfer roller Transfer roller collar Shaft (Conductive grease) Paper guide

✕ {

✕ {

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

▲ ▲ ▲ ✕ ✕ {

▲ ▲ ▲ ▲ ✕ {

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [45]-25) (P/G No.: [45]-50) (P/G No.: [45]-47) (P/G No.: [45]-48) UKOG-0012QSZZ

* When cleaning the transfer belt, never use alcohol, solvent, and water.

1

5

4 2

3

5

4

MX-M700N TRANSFER SECTION M – 5

5 5

MX-M700N

[N] FUSING SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram PCUPWB CN-2 B28B-PHDSS-B RTH1 6 HLPR3 7 GND2 8 HLCNT1 9 10 RTH2 HLCNT2 11 GND2 12 +24V1 13 14 RTH3 /MSWPR 15 GND2 16 CN-24 B6B-PH-K-S +5V-WEBENDD 1 WEBENDD 2 3 GND2 WEBMA 4 WEBMB 5 Reserve7 6 CN-1 B03P-VL HL1-N HL3-L HL2-L

1 2 3

CN-2 B03P-VL-R 1 HL1-L 2 HL2-N 3 HL3-N

9 8 7 6 5 4

RCZR-09V-PS RTH1 GND2 RTH2 GND2 RTH3 GND2

PHNR-04-H+BU04P-TR-P-H 1 RTH1 4 2 GND2 3 2 3 RTH2 4 GND2 1

1 2 3 4 5 6

PHNR-02-H+BU02P-TR-P-H 1 RTH3 2 2 GND2 1

PHNR-05-H+BU05P-TR-P-H 1 +5V-WEBENDD 5 2 WEBENDD 4 3 GND2 3 4 WEBMA 2 5 WEBMB 1

RCZR-10V-PS 1 +5V-WEBENDD 10 2 WEBENDD 9 3 GND2 8 4 WEBMA 7 5 WEBMB 6

1 2 3 4 5 6

HL-2L HL-1N HL-2N HL-3N HL-3L HL-1L

179228-32 1 +5V-WEBENDD 2 WEBENDD 3 GND2 SMR-02V-N/SMP-02V-NC 1 WEBMA 1 WEBMB 2 2

1 2 3 4 5 6

19LP-RWZV-K4GG-P6/ 19LR-RWZV-K2GG-R6

SUB P/S PWB

FUM WEBM

8 9

1

HL 2

WEBEND HLTS2 HLTS1

3 10

HL1 RT H1 HL3

4

RTH2

2 5

7

HLTS3 RTH 3

6 2

RTH1

Signal name RTH1

RTH2

RTH2

HLTS1

HLTS1

Fusing temperature sensor (1) Fusing temperature sensor (2) Thermostat (1)

HLTS2

HLTS2

Thermostat (2)

HL1 HL2 RTH3

HL1 HL2 RTH3

HLTS3

HLTS3

Heater lamp (1) Heater lamp (2) Fusing temperature sensor (3) Thermostat (3)

HL3 FUM WEBEND

HL3 FUM WEBEND

Heater lamp (3) Fusing motor Web end sensor

WEBM

WEBM

Web motor

Code

Name

Type Thermistor Thermistor

Thermistor

Transmission type

Function/Operation Detects the surface temperature of the heat roller. (Center section) Detects the surface temperature of the heat roller. (Edge section) Shuts conduction to the heater lamp when the temperature rises abnormally. [For the heat roller] Shuts conduction to the heater lamp when the temperature rises abnormally. [For the heat roller] Heats the heat roller. Heats the heat roller. Detects the surface temperature of the sub heat roller. Shuts conduction to the heater lamp when the temperature rises abnormally. [For the sub heat roller] Heats the sub heat roller. Drives the fusing unit. Detects the web paper end (Replacement). Drives the web roller.

MX-M700N FUSING SECTION N – 1

Active condition Anaput Anaput

Anaput

End detection

NOTE

No.

Name

1 2

Heat roller Separation pawl

3 4 5

Pressure roller Sub heat roller Separation pawl

6 7 8 9 10

Cleaning sheet CL roller Web roller Pressure roller Lower CL roller DG2

Active condition

Function/Operation

NOTE

Heats and presses toner on paper and fuses it on paper. Mechanically separates paper which was not separated naturally from the heat roller. Heats and presses toner on paper and fuses it on paper. Heats the pressure roller. Mechanically separates paper which was not separated naturally from the pressure roller. Clean the sub heat roller surface. Clean the pressure roller. Clean the heat roller. Applies a pressure to web paper to connect the heat roller. Clean the pressure roller.

2. Operational descriptions A. General

D. Fusing operation

This section performs the following functions and operations.

Toner on paper is heated and pressed to be fused by the heat roller.

1)

Toner attached to paper in the transfer section are heated and pressed by the fusing roller onto paper to fuse.

2)

The sub heat roller is used to improve fusing capacity and separation capacity after fusing.

Copy

Paper exit

Paper exit roller

Fusing

Fusing motor

Heat roller

Pressure roller

Heater lamps (2 pcs.)

Sub heat roller

Sub power PWB

Heat lamp (1 pc)

B. Fusing unit drive To drive the fusing unit, the drive power is transmitted from the drive motor (FUM) through the connection gear to the upper heat roller gear. The drive motor (stepping motor) is driven according to the control signal sent from the PCU.

PCU

Heat roller HL2

FUM

HL1

Paper exit Pressure roller

C. Heater lamp drive

HL3 Sub heat roller

The surface temperature of the heat roller detected by the thermistor is sent to the PCU. When the temperature is lower than the specified level, the heater lamp lighting signal is sent from the PCU to the heater lamp drive circuit in the sub power PWB.

Two heater lamps are provided for the heat roller and one heater lamp is provided for the sub heat roller for the pressure roller to sub heat paper from above and below.

The power triac in the heater lamp drive circuit is turned on, and the AC power is supplied to the heater lamp, lighting the lamp and heating the heat roller.

This is because toner on paper must be heated from above and below to be fused on paper.

To prepare for an abnormally high temperature of the heat roller, the thermostat is provided for safety.

Pressure roller are of silicon rubber because of the following reasons and purpose. This is the following reason, objective. 1)

Paper is separated upward. (Since the heat roller is of higher hardness, the pressure roller is deformed to separate paper upward.)

2)

The nip quantity is increased to increase heat capacity for paper.

3)

By pressing paper with the flexible roller, toner is fused without deformation. (The flatness, however, is not so high.)

When the thermostat is opened, power supply (AC line) to the heater lamp is cut off.

MX-M700N FUSING SECTION N – 2

E. Fusing temperature control

3. Disassembly and assembly

The temperature sensor is provided at the center of the heat roller and the sub heat roller.

A. F section

The roller temperature is detected by the installed temperature sensor, and the heater lamp is controlled so that the temperature is maintained at the specified level.

No.

Unit

Parts

㧔㧕 Fusing unit

a b c d e f g h i j k l m n o p q r s t u v w x y

In addition, the fusing temperature is switched according to the kind of paper. Mode Ready condition Print mode

Paper Standard paper Thick paper Tab paper Postcard –-

Pre-heat

Fusing roller 185°C 220°C 220°C 200°C 140°C

Sub heat roller 185°C 180°C 180°C 200°C 140°C

F. Cleaning operation The fusing roller removes toner and dusts from the heat roller and the pressure roller surfaces by the following three methods. • Sub-heat roller: Clean the sub heat roller with the cleaning sheet. • Pressure roller: Mechanical cleaning by the CL roller. • Heat roller: Mechanical cleaning by the web roller.

4 2

Web end sensor Web motor Pressure bearing Pressure roller Web roller Web bearing Heat roller separation pawl Pressure roller separation pawl Pressure roller CL roller CL roller bearing Lower CL roller DG2 Heater lamp main Heater lamp sub Heat roller gear Heat roller Thermistor (upper) Thermostat (upper main) Thermostat (upper sub) Thermostat (lower) Thermistor (lower) Cleaning sheet table Sub heater lamp Sub heat roller bearing Sub heat roller

▲ ✕▲ ✕▲ ▲ ✕▲ ✕▲ ✕▲ ✕▲ ▲ ✕▲

✕ ✕▲ ✕

✕ ✕▲ ▲ ✕▲

(1)-g (1)-x

(1)-k (1)-h

8 3

Mainte nance ✕

(1)-t (1) (1)-h

7

(1)-g 6

(1)-j

(1)-o (1)-k

(1)-k

1

(1)-o (1)-s

5

No. 1 2 3 4 5 6 7 8

(1)-r (1)-q (1)-c (1)-u

Name Cleaning sheet Pressure roller Discharge brush Heat roller Sub heat roller CL roller Web roller Lower CL roller DG2

(1)-f

(1)-q (1)-x

(1)-k

(1)-l (1)-c

(1)-d

(1)-c (1)-f

(1)-b

(1)-e

(1)-a (1)-q (1)-r࡮s (1)-n (1)-m (1)-p

(1)-g (1)-h (1)-i (1)-j (1)-y (1)-v (1)-l (1)-w

MX-M700N FUSING SECTION N – 3

(1)-t (1)-u

(1) 1)

Fusing unit

a. Web end sensor

Open the left door unit.

1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Check the web end sensor.

2 1

2)

Remove the blue fixing screw on the front side. b. Web motor

3)

Release the fixing on the rear frame side.

4)

Release the right and left lock levers of the fusing unit to remove the fusing unit.

1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Disconnect the connector, and remove only the 4 pin connector harness.

3)

Remove the 3 screws.

* Caution for handling at a high temperature (Hold the both sides of the unit.) * When removing the unit, be careful not to tilt it, and remove slowly. (This is because the unit includes paper dust scraped by the scraper.)

MX-M700N FUSING SECTION N – 4

4)

7)

Remove the web unit.

Remove the E-ring, and remove the gear from the web motor.

c. Pressure bearing d. Pressure roller e. Web roller f. Web bearing 5)

6)

Remove the heat-resistant band banding web motor harness and cut it.

1) 2)

Remove the web unit. (See “b. Web motor”)

Cut the banding band and remove it from the web motor.

3)

Disconnect the connector. Remove the screws, and remove the web drive unit. Remove the bearings.

4)

Disconnect the connector. Remove the screws, and remove the cover.

Remove the 2 screws and remove the web motor.

Remove the fusing unit. (See “(1) Fusing unit”)

Note: The shoulder screws go on the front side and the standard screw go on the rear side.

MX-M700N FUSING SECTION N – 5

5)

Remove 3 screws, and remove the web end sensor unit.

8)

Remove the spring, and remove the pressure bearing. Remove the pressure roller.

* When installing, put the boss of actuator in the inside of a websheet.

9)

Remove the web tension bearing and the backup plate.

6)

Remove 2 screws of backup plate.

7)

Remove the web roller (wind-up side).

10) Remove the web roller.

* When installing, rotate the web roller until the blue line (approx. 30cm) is hidden after installing the web roller. (rotate the gear)

MX-M700N FUSING SECTION N – 6

11) Remove the E-rings and the gears.

g. Heat roller separation pawl

* When installing the one way gear, direct the metal surface side to outside.

1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Remove the heat roller separation pawl unit.

Marks B

A

B Marks

* When installing the unit, install to the standard position (A). (If the picture quality may be degraded damaged by the roller damage, change the installing position to (B).)

12) Remove the pins and E-rings, and remove the winding shaft and the transport shaft. * When installing, install the winding shaft (two pin holes) in an attachment hole (A) of the “{{” mark side, and install transport shaft (one pin hole) in an attachment hole (B) of the “{” mark side.

A

3)

Remove the heat roller separation pawl unit.

A

B h. Pressure roller separation pawl 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Open the pressure roller separation pawl unit.

3)

Remove the pressure roller separation pawl.

13) Remove the web bearings.

MX-M700N FUSING SECTION N – 7

i. Pressure roller

6)

Remove the CL roller unit.

7)

Remove the CL roller bearings to CL roller.

8)

Remove the lower CL roller DG2 unit.

9)

Remove the CL roller bearings to lower CL roller DG2.

j. CL roller k. CL roller bearing l. Lower CL roller DG2 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Alternately tighten the screws to release pressure. * When releasing the pressure, do not apply any force to the shaded area. (Otherwise, the paper guide on the paper entry side may be deformed.)

3)

Remove the screws and open the fusing unit.

4)

Remove the pressure roller unit.

5)

Remove the bearings from the pressure roller.

[Caution when attaching] When installing the pressure roller to the fusing unit, be careful not to damage the cleaning plate. If the cleaning plate would be deformed, copy dirt would be resulted. MX-M700N FUSING SECTION N – 8

m. Heater lamp main

7)

n. Heater lamp sub

Remove the ring, and remove the heat rollers, gear and bearings.

o. Heat roller gear p. Heat roller 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Alternately tighten the screws to release pressure.

3)

Remove the fusing unit. (See “i. Pressure roller”)

4)

Remove the lamp fixing screws.

(See “i. Pressure roller”)

q. Thermistor (upper)

R side

1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Remove the web unit. (See “b. Web motor”)

3)

Remove the screws, and remove the mounting plate.

4)

Remove 1 screw per Thermistor.

F side

* When assembling, tighten the screws in the front side (drawer CN side) and then in the rear side (gear side) in this sequence. * Check that the screw is securely tightened again. (If the screw is loose, the becomes defective to cause an overheating.) 5)

6)

Remove the heater lamp main and sub.

Remove the heat roller unit.

MX-M700N FUSING SECTION N – 9

r. Thermostat (upper main)

3)

Remove the thermistor (lower).

s. Thermostat (upper sub) 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Remove the web unit. (See “b. Web motor”)

3)

Remove the lamp fixing screws on R side.

[Cleaning] 4)

Disconnect the connector on drawer side.

5)

Remove the screws and the washers, and remove the upper main thermostat (A) and the upper sub thermostat (B).

When there is paper dust or foreign material on the heat sensitive surface of the thermostat, clean and remove dust or foreign material. [Caution when attaching] Be careful not to mistake the install position of the washer. 4)

B

Disconnect the connector. Remove the screws, and the thermistor (lower).

A

Marks

A B

t. Thermostat (lower) * If the picture quality may be degraded damaged by the roller damage, change the installing position to (B).

u. Thermistor (lower) 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Lay the unit on its side to prevent paper dust from dispersing, and remove the lower cover.

v. Cleaning sheet table 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Remove the lower cover. (See “t. Thermostat (lower)”)

3)

Remove the holder plate.

(A)

* When there are paper dusts or foreign materials at the port area (A), clean and remove.

MX-M700N FUSING SECTION N – 10

4)

Remove the cleaning sheet table.

6)

Remove the sub heat roller unit.

* If the roller is cooled down, toner may be hardened to prevent removing. * Since cleaning is performed by applying a pressure by the spring, be careful not to deform it. * If copy dirt is heavy, replace the cleaning sheet table with a new one.

w. Sub heater lamp

7)

Remove the lamp fixtures.

8)

Remove the sub heater lamp.

9)

Remove the ring, and remove the thermostat (lower) and the sub heat roller.

x. Sub heat roller bearing y. Sub heat roller 1)

Remove the fusing unit. (See “(1) Fusing unit”)

2)

Remove the lower cover. (See “t. Thermostat (lower)”)

3)

Remove the springs.

4)

Remove the thermostat terminals.

5)

Remove the thermistor.

Marks

A B

* If the picture quality may be degraded damaged by the roller damage, change the installing position to (B). MX-M700N FUSING SECTION N – 11

4. Maintenance ✕ : Check

▲: Replace

{: Clean

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust as necessary.) 250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲

✕

✕

✕

✕

✕

✕

✕

✕

✕

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

✕ ▲ ▲ ▲ ▲ { ✩ ✩ ▲ ▲

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Fusing unit

No. 1 2 3 4 5 6 7 8 9 10 11

Part name Heat roller Pressure roller Sub heat roller Web roller Pressure roller CL roller CL auxiliary roller bearing Cleaning sheet table Heat roller separation pawl Pressure roller separation pawl Thermistor (upper/lower)

12 13 14 15 16 17 18 19 20 21

Heat roller gear (Grease) Sub heat roller bearing CL roller bearing Web bearing Pressure bearing Paper guides Gears Shaft (Grease) Lower CL roller DG2 CL roller bearing

{

✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [48]-3) (P/G No.: [46]-24) (P/G No.: [46]-14) (P/G No.: [49]-42) (P/G No.: [49]-44) (P/G No.: [47]-46) (P/G No.: [46]-23) (P/G No.: [48]-9) (P/G No.: [47]-26) Paper dust removal is required. UKOG-0235FCZZ (P/G No.: [46]-7) (P/G No.: [47]-45) (P/G No.: [49]-4) (P/G No.: [49]-8)

UKOG-0235FCZZ (P/G No.: [47]-47) (P/G No.: [47]-45)

* When maintenance, replace the fusing web roller. When used without replacement, the picture quality may be damaged because web roller end. [every 300K every 250K]

21

9 14 10

3

10

11

9 1 2 21

19 14

17 11

13

19

11 19 16

12 20 13

15 5 15

6

16

19 4 MX-M700N FUSING SECTION N – 12

MX-M700N [O] PAPER EXIT SECTION

5GTXKEG/WCN

1. Electrical and mechanism relation diagram

POM1

POD2 POM2

CFM-U3

INTPWB

POD3 POD1

CFM-U4 CFM-U1

2 1

2 3

3 1

DELIVERY UNIT SMR-06V-N/SMP-06V-NC 1 2 3 4 5 6

CN-1 B12B-PH-K-S 1 /POM1/A 2 /POM1A 3 /POM1B 4 /POM1/B 5 +24V2 6 +24V2 7 /POM2/A 8 /POM2A 9 /POM2B 10 /POM2/B 11 +24V2 12 +24V2

1 2 3 4 5 6

PCU PWB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

CN-10 B26B-PHDSS-B /POM1A /POM1XA /POM1B /POM1XB /POM2A /POM2XA /POM2B /POM2XB /1A /1XA /1B /1XB /2A /2XA /2B /2XB /TRMA /TRMXA /TRMB /TRMXB /VPMA /VPMXA /VPMB /VPMXB GND2 GND2

CN-5 B32B-PHDSS-B 1 GND2 2 +24V1 3 POD1 4 /VFM-EX1 5 +5V2 6 GND2 7 GND2 8 +24V1 9 POD2 10 /VFM-EX2 11 +5V2 12 GND2 13 GND2 14 +24V1 15 POD3 /VFM-EX3 16 17 +5V2 18 GND2 19 +24V1 20 +24V1 /CFM-U1 21 /VFM-BKL 22 23 GND2 24 GND2 25 +24V 26 +24V1 /CFM-U3 27 /CFM-U2 28 29 GND2 30 GND2 31 TH-EX 32 GND2 CN-8 B20B-PHDSS-B /PWM-RSV1 20

SMP-18V-NC/SMR-18V-N 1 GND2 1 2 POD1 2 3 +5V2 3 4 GND2 4 5 POD2 5 6 +5V2 6 7 GND2 7 8 POD3 8 9 +5V2 9 10 +24V1 10 11 /CFM-U1 11 12 GND2 12 13 +24V1 13 14 /CFM-U3 14 15 GND2 15 16 16 TH-EX 17 17 GND2 18 /PWM-RSV1 18

1 2 3

1 2 3 4 5 6

PHR-3 GND2 POD1 +5V2 PHR-3(RED)

1 2 3

GND2 POD2 +5V2

SMP-03V-BC/SMR-03V-B 1 GND2 1 1 2 POD3 2 2 3 +5V2 3 3

PHR-3 GND2 POD3 +5V2

SMR-03V-N/SMP-03V-NC 1 +24V1 1 2 /CFM-U1 2 3 GND2 3

PHNR-03-H+BU03P-TR-P-H 1 3 +24V1 2 /PWM-RSV1 2 3 1 GND2

SMP-02V-NC/SMR-02V-N

1 2 3 4

S4B-PH-K-S (NC) (NC) TH-EX GND2

1 /PWM-RSV1 1 2 2 (NS)

POD1

Paper exit detector 1

Paper exit detection from fusing

POD2

POD2

Paper exit detector 2

Paper detection from paper exit

POD3

POD3

Paper exit detector 3

Paper exit detection to upper section

POM1

POM1

Paper exit motor 1

Drives the paper transport roller 16.

Name

/POM2/A /POM2A /POM2B /POM2/B +24V2 +24V2

SMR-03V-N/SMP-03V-NC 1 1 +24V1 2 /CFM-U3 2 3 3 GND2

Signal name POD1

Code

1 2 3 4 5 6

SMR-06V-N/SMP-06V-NC

DRIVER PWB CN-4 B26B-PHDSS-B 1 /POM1A 2 /POM1XA 3 /POM1B 4 /POM1XB 5 /POM2A 6 /POM2XA 7 /POM2B 8 /POM2XB 9 /1A 10 /1XA 11 /1B 12 /1XB 13 /2A 14 /2XA 15 /2B 16 /2XB 17 /TRMA 18 /TRMXA /TRMB 19 /TRMXB 20 /VPMA 21 /VPMXA 22 /VPMB 23 /VPMXB 24 25 GND2 26 GND2

/POM1/A /POM1A /POM1B /POM1/B +24V2 +24V2

Function/Operation

MX-M700N PAPER EXIT SECTION O – 1

Type Transmission type Transmission type Transmission type Stepping motor

NOTE Paper transport system sensor Paper transport system sensor Paper transport system sensor Selection of Normal speed/ High speed

POM2

Signal name POM2

CFM-U1

CFM-U1

CFM-U3

CFM-U3

CFM-U4

PWMRSV1

Code

INTPWB No. 1 2 3

Name

Function/Operation

Type

Paper exit motor 2

Drives the paper exit roller 1.

Stepping motor

Fusing cooling fan motor 1 (Paper exit, duplex (ADU) section) (Front surface) Fusing cooling fan motor 3 (Paper exit, duplex (ADU) section) (Front surface) Fusing cooling fan motor 4 (Paper exit, duplex (ADU) section) (Paper exit section rear side) Paper exit temperature sensor

Exhaust heat from the fusing section.

DC brush-less motor

Exhaust heat from the fusing section.

DC brush-less motor

PWM control

Cools paper which is discharged to the inner tray.

DC brush-less motor

PWM control

Name

Paper exit section temperature detection

Function/Operation Transports paper from the fusing roller to the paper exit roller 1. Discharges paper to the paper exit tray. / Switches back paper. Discharges paper.

Transport roller 16 Paper exit roller 1 Paper exit roller 3

2. Operational descriptions A. Outline The paper exit and turning section discharges paper which is transported from the fusing section, and detects paper full. It also turns paper to transport it to the duplex or the finisher.

(1)

Paper exit unit

1)

Open the left door.

2)

Remove the DSPF paper exit tray.

3)

Remove the top left cabinet.

4)

Remove the front left cabinet.

5)

Remove the paper exit port cabinet.

3. Disassembly and assembly A. Paper exit section No. (1)

Unit

No.

Paper exit unit

a b c d e f g h i j k

Parts Transport roller 16 Paper exit roller 1 Fusing cooling fan motor 1 Fusing cooling fan motor 3 Fusing cooling fan motor 4 Paper exit temperature sensor Paper exit detector 1 Paper exit detector 2 Discharge brush Paper exit detector 3 Paper exit roller 3

Mainte nance {✕ {✕

✕ {✕

(1)-h

(1) (1)-e (1)-d (1)-f (1)-c

(1)-j (1)-g

(1)-k

(1)-i

(1)-i (1)-a

NOTE

(1)-b

MX-M700N PAPER EXIT SECTION O – 2

Selection of Normal speed/ High speed PWM control

6)

Disconnect the connectors.

7)

Remove the front fixing bracket.

8)

Remove the paper exit unit in the arrowed direction.

4)

Remove the E-ring to remove the gear.

5)

Remove the transport roller 16.

a. Transport roller 16 1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the ground plate. Remove the E-ring to remove the pulley.

b. Paper exit roller 1

3)

1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the upper unit.

Remove the stopper. Remove the E-ring to remove the bearing.

MX-M700N PAPER EXIT SECTION O – 3

3)

Remove the stopper. Remove the E-ring to remove the bearing.

6)

Remove the paper exit roller 1.

c. Fusing cooling fan motor 1 d. Fusing cooling fan motor 3 4)

5)

Remove the ing plate. Remove the connection plate, and remove the gears.

e. Fusing cooling fan motor 4 1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the upper cover.

3)

Remove the fusing cooling fan motor 1 (A), 3 (B), and 4 (C).

Remove the E-ring to remove the gear.

C B A

REVERSE

Fan blowing direction

[Caution when attaching] • When assembling, be careful of the direction of the fan. (Fit the fan with the mark rotating direction)

MX-M700N PAPER EXIT SECTION O – 4

f. Paper exit temperature sensor

h. Paper exit detector 2

1)

Remove the upper cover. (See “c. Fusing cooling fan motor 1”)

1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the paper exit temperature sensor.

2)

Remove the upper cover. (See “c. Fusing cooling fan motor 1”)

3)

Remove the paper exit detection 2 detector.

i. Discharge brush g. Paper exit detector 1 1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the follower roller unit.

3)

Remove the paper exit detection 1 detector.

1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the discharge brush. * When attaching, attach it to the reference.

MX-M700N PAPER EXIT SECTION O – 5

j. Paper exit detector 3

k. Paper exit roller 2

1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

1)

Remove the paper exit unit. (See “(1) Paper exit unit”)

2)

Remove the upper cover. (See “c. Fusing cooling fan motor 1”)

2)

Remove the upper cover. (See “c. Fusing cooling fan motor 1”)

3)

Disconnect the connector, and remove the harness protect sheet. Remove the paper guide.

3)

Remove the paper guide. (See “j. Paper exit detector 3”)

4)

Remove the ground plate. Remove the E-ring to remove the bearing.

5)

Remove the E-ring, and the gear. Remove the spring pin and the bearing.

6)

Remove the paper exit roller 3.

4)

Remove the cover, and the remove the paper exit detector 3.

MX-M700N PAPER EXIT SECTION O – 6

4. Maintenance ✕: Check

{: Clean

▲: Replace

✩: Lubricate

U: Adjust

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Paper exit reverse section

No. 1 2 3

Part name Transport rollers Discharge brush Shaft (Conductive grease)

✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

{ ✕ ✕

1 1 1

2

2 3

3

MX-M700N PAPER EXIT SECTION O – 7

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

UKOG-0012QSZZ

MX-M700N

[P] DRIVE SECTION

a. Paper exit motor 1 5GTXKEG/WCN b. Paper exit motor 2

1. Disassembly and assembly

1)

Remove the fusing unit. (See “(1) Fusing unit” in the “FUSING SECTION”)

A. Fusing drive section

2)

Remove the fusing drive unit. (See “b-1. Fusing motor”)

3)

Disconnect the connector, and remove the fusing drive frame.

4)

Remove the paper exit motor 1 (A) and the paper exit motor 2 (B).

No. (1)

Unit Fusing drive unit

(2)

Others

No. a b a

Parts Paper exit motor 1 Paper exit motor 2 Fusing motor

(1)-a

(1)-b (2)-a (1)

B

(1)

Fusing drive unit

1)

Remove the fusing unit. (See “(1) Fusing unit” in the “FUSING SECTION”)

2)

Remove the fusing motor. (See “(2)-a. Fusing motor”)

3)

Disconnect the connector and remove the harnesse clamp.

A

(2)

Others

a. Fusing motor 1)

4)

Remove the rear cabinet and the rear cabinet upper.

Remove the fusing drive unit. * Remove the screw which was indicated with the arrow mark.

MX-M700N DRIVE SECTION P – 1

2)

B. Drum drive section

Remove the tray.

No. (1)

Unit Drum drive unit

(2)

Others

No. a b a b

Parts Waste toner pipe lock detector Process humidity sensor OPC drum motor Developing system

(1) (1)-a

3)

(1)-b

Remove the left cover cabinet.

(2)-a

(2)-b

(1)

4)

5)

Disconnect the connector and remove the harness clamp, and remove the paper exit tray duct R unit.

Drum drive unit

1)

Remove the developing unit and the process unit. (See “(1) Developing unit” in the “DEVELOPING SECTION”, “A-(1) Process unit” in the “PHOTOCONDUCTOR SECTION”)

2)

Remove the OPC drum motor and the developing motor. (See “(2)-a. OPC drum motor”, “(2)-b. Developing system”)

3)

Disconnect the connector, and remove the harness from the harness holder.

4)

Disconnect the connector and remove the harness clamp, and remove the drum drive unit.

Disconnect the connector and remove the fusing motor.

* Remove the screw which was indicated with the arrow mark.

MX-M700N DRIVE SECTION P – 2

a. Waste toner pipe lock detector 1)

Remove the developing unit and the process unit. (See “(1) Developing unit” in the “DEVELOPING SECTION”, “A-(1) Process unit” in the “PHOTOCONDUCTOR SECTION”)

2)

Remove the OPC drum motor and the developing motor. (See “(2)-a. OPC drum motor”, “(a)-b. Developing motor”)

3)

Remove the drum drive unit. (See “(1) Drum drive unit”)

4)

Disconnect the connector, and remove the waste toner pipe lock detector.

7)

Remove the parts.

8)

Disconnect the connector, and remove the sensor plate.

9)

Remove the process humidity sensor.

b. Process humidity sensor 1)

Remove the developing unit. (See “(1) Developing unit” in the “DEVELOPING SECTION”)

2)

Remove the process unit. (See “a. Process unit” in the “PHOTOCONDUCTOR SECTION”)

3)

Remove the OPC drum motor and the developing motor. (See “(2)-a. OPC drum motor”, “(a)-b. Developing motor”)

4)

Remove the drum drive unit. (See “(1) Drum drive unit”)

5)

Remove the drum earth plate. Remove the set screw and the flywheel t. Remove the E-ring.

6)

Disconnect the connector, and remove the drum drive frame.

(2)

Others

a. OPC drum motor b. Developing system 1)

Remove the rear cabinet.

MX-M700N DRIVE SECTION P – 3

2)

(1)

Remove the flywheel.

1)

3)

Main drive unit Remove the resist roller unit. (See “B-(1) Resist roller unit” in the “PAPER TRANSPORT SECTION”)

2)

Remove the flywheel. (See “B-(2)-a. OPC drum motor”)

3)

Remove the main motor. (See “(2)-a. Main motor”)

4)

Disconnect the connector, and remove the eternal outfit mounting plate.

5)

Remove the plastic E-ring, the belt holding sheet, the belt, and the pulley. Remove the t plate.

Disconnect the connector, and remove the OPC drum motor (A) and the developing motor (B).

A

* When installing, be careful of the direction of the belt holding sheet.

B

C. Paper feed/paper transport drive section No. (1)

Unit Main drive unit

(2)

Others

No. a b a

Parts Resist roller front drive motor Resist roller clutch Main motor

6)

Disconnect the connector, and remove the main drive unit. * Remove the screw which was indicated with the arrow mark.

(1)-b

(2)-a (1)-a (1)

MX-M700N DRIVE SECTION P – 4

a. Resist roller front drive motor 1)

7)

Remove the resist roller unit. (See “B-(1) Resist roller unit” in the “PAPER TRANSPORT SECTION”)

2)

Remove the flywheel. (See “B-(2)-a. OPC drum motor”)

3)

Remove the main motor. (See “(2)-a. Main motor”)

4)

Remove the main drive unit. (See “(1) Main drive unit”)

5)

Remove the resist roller front drive motor.

(2)

Remove the bearing, the E-ring, and the set screw, and remove the resist roller clutch.

Others

a. Main motor 1)

Remove the rear cabinet.

2)

Disconnect the connector, and remove the main motor.

b. Resist roller clutch 1)

Remove the resist roller unit. (See “B-(1) Resist roller unit” in the “PAPER TRANSPORT SECTION”)

2)

Remove the flywheel. (See “B-(2)-a. OPC drum motor”)

3)

Remove the main motor. (See “(2)-a. Main motor”)

4)

Remove the main drive unit. (See “(1) Main drive unit”)

5)

Disconnect the connector, and remove the main drive frame.

6)

Disconnect the connector, and remove the resist roller clutch unit.

* When installing, be sure to ensure that the projection of the plate is engaged in the clutch rotation stopper.

MX-M700N DRIVE SECTION P – 5

D. Manual paper feed drive section No. (1)

3)

Unit Manual paper feed drive unit

* When installing, be careful of the direction of the belt holding sheet.

(1) 4)

(1) 1)

Remove the plastic E-ring, the belt holding sheet, the belt, and the pulley.

Remove the harness from the clamp, and remove the manual paper feed unit.

Manual paper feed drive unit Remove the rear cabinet.

* Remove the screw which was indicated with the arrow mark.

E. 1/2 paper feed drive section No. (1)

Unit 1/2 paper feed drive unit

No. a b c d e f

2)

Disconnect the connector, the harness clamp, and the earth wire. Remove the high voltage PWB unit.

(2)

Others

a b c

Parts Vertical paper transport motor Paper feed tray 3/4 paper transport clutch 2 Paper feed clutch (Paper feed tray 1) Horizontal paper transport clutch Paper feed clutch (Paper feed tray 2) Paper pickup solenoid (Paper feed tray 1) Remove the paper tray lift-up motor (paper feed tray 1) Paper tray lift-up motor (Paper feed tray 2) Paper pickup solenoid (Paper feed tray 2)

(1)-f (1)-c (1)-d (1)-b (1)-e (2)-a (2)-c (2)-b (1)

MX-M700N DRIVE SECTION P – 6

(1)-a

(1)

1/2 paper feed drive unit

7)

1)

Remove the main motor. (See “C-(2)-a. Main motor”)

2)

Remove the high voltage PWB unit. (See “D-(1) Manual paper feed drive unit”)

3)

Pull out the left door.

* When installing, temporarily fix the 1/2 paper feed drive unit to the main unit, and install the drive t plate. Then tighten the screw of the drive unit securely.

2 1

4)

Remove the harness, and remove the drive t plate.

8)

Disconnect the connector and remove the harness clamp. Remove the 1/2 paper feed drive unit.

Disconnect the connector and remove the harness clamp. Remove the DV fan unit.

* If the left door is completely pulled out, the unit may drop off. Be careful to avoid it. * Remove the screw which was indicated with the arrow mark. a. Vertical paper transport motor 5)

6)

Disconnect the connector and remove the harness holder.

1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Loosen the screw to release the tension, and remove the belt.

3)

Remove the parts.

Remove the plastic E-ring, the belt holding sheet, the belt, and the pulley. Remove the t plate.

Belt length 297

Belt length 399

Belt length 300

* When installing, be careful of the belt length and the belt holding sheet direction.

* Attach the spring to the longer shaft.

MX-M700N DRIVE SECTION P – 7

4)

Remove the 1/2 paper feed drive frame lower. Remove the harness clamp.

5)

Disconnect the connector, and remove the vertical paper transport motor.

4)

Remove the E-ring, and remove the paper feed tray 3/4 paper transport clutch 2.

c. Paper feed clutch (Paper feed tray 1) 1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Remove the 1/2 paper feed drive frame lower. (See “a. Vertical paper transport motor”)

3)

Disconnect the connector and remove the harness clamp, and remove the paper feed clutch (paper feed tray 1) unit.

4)

Remove the E-ring, and remove the paper feed clutch (paper feed tray 1).

b. Paper feed tray 3/4 paper transport clutch 2 1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Remove the 1/2 paper feed drive frame lower. (See “a. Vertical paper transport motor”)

3)

Disconnect the connector and remove the harness clamp, and remove the paper feed tray 3/4 paper transport clutch 2.

MX-M700N DRIVE SECTION P – 8

d. Horizontal paper transport clutch

4)

1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Remove the 1/2 paper feed drive frame lower. (See “a. Vertical paper transport motor”)

3)

Disconnect the connector and remove the harness clamp, and remove the horizontal paper transport clutch.

Remove the E-ring, and remove the paper feed clutch (paper feed tray 2).

f. Paper pickup solenoid (Paper feed tray 2)

4)

1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Remove the 1/2 paper feed drive frame lower. (See “a. Vertical paper transport motor”)

3)

Remove the paper pickup solenoid unit.

4)

Remove the paper pickup solenoid.

Remove the E-ring, and remove the horizontal paper transport clutch.

e. Paper feed clutch (Paper feed tray 2) 1)

Remove the 1/2 paper feed drive unit. (See “(1) 1/2 paper feed drive unit”)

2)

Remove the 1/2 paper feed drive frame lower. (See “a. Vertical paper transport motor”)

3)

Disconnect the connector and remove the harness clamp, and remove the paper feed clutch (paper feed tray 2).

* When installing, check that the solenoid plunger is inserted in the arm.

MX-M700N DRIVE SECTION P – 9

(2)

Others

b. Paper tray lift-up motor (Paper feed tray 2)

a. Remove the paper tray lift-up motor (paper feed tray 1) 1)

2)

1)

Remove the high voltage PWB unit. (See “D-(1) Manual paper feed drive unit”)

2)

Disconnect the connector, and remove the lift-up motor unit.

3)

Release the pawl, and remove the lift-up coupling. Remove the liftup spring from the lift-up motor.

Remove the rear cabinet.

Remove the plastic E-ring, the belt holding sheet, the belt, and the pulley.

c. Paper pickup solenoid (Paper feed tray 2) 1)

Remove the high voltage PWB unit. (See “D-(1) Manual paper feed drive unit”)

2)

Disconnect the connector, and remove the paper pickup solenoid unit.

3)

Remove the paper pickup solenoid.

* When installing, be careful of the direction of the belt holding sheet. 3)

4)

Disconnect the connector, and remove the lift-up motor unit.

Release the pawl, and remove the lift-up coupling. Remove the liftup spring from the paper tray lift-up motor.

* When installing, check that the solenoid plunger is inserted in the arm.

MX-M700N DRIVE SECTION P – 10

F. 3/4 paper feed drive section No. (1)

Unit 3/4 paper feed drive unit

(2)

Others

No. a b c a b

4)

Parts Paper feed clutch (Paper feed tray 3) Paper feed clutch (Paper feed tray 4) Paper feed tray 3/4 paper transport clutch 1 Paper tray lift-up motor (Paper feed tray 3) Paper tray lift-up motor (Paper feed tray 4)

Disconnect the connector and remove the harness clamp. Remove the 3/4 paper feed drive unit. * Remove the screw which was indicated with the arrow mark.

(1)-a (1)-c (2)-a (1)-b (2)-b a. Paper feed clutch (Paper feed tray 3)

(1)

(1)

1)

Remove the 3/4 paper feed drive unit. (See “(1) 3/4 paper feed drive unit”)

2)

Remove the E-ring and remove the parts.

3)

Remove the 3/4 drive frame lower.

3/4 paper feed drive unit

1)

Remove the paper tray lift-up motor. (See “(2)-a. Paper tray lift-up motor (Paper feed tray 3)”)

2)

Remove the parts and remove the drive t plate.

* When installing, be careful of the direction of the belt holding sheet. * When installing, temporarily fix the 1/2 paper feed drive unit to the main unit, and install the drive t plate. Then tighten the screw of the drive unit securely. 3)

Remove the external outfit mounting plate.

MX-M700N DRIVE SECTION P – 11

4)

Disconnect the connector, and remove the paper feed clutch unit.

4)

Remove the E-ring, and remove the paper feed clutch.

c. Paper feed tray 3/4 paper transport clutch 1

5)

1)

Remove the 3/4 paper feed drive unit. (See “(1) 3/4 paper feed drive unit”)

2)

Remove the parts, and remove the belt.

3)

Remove the 3/4 drive frame lower. (See “a. Paper feed clutch (Paper feed tray 3)”)

4)

Disconnect the connector, and remove the paper feed tray 3/4 paper transport clutch 1 unit.

Remove the E-ring, and remove the paper feed clutch.

b. Paper feed clutch (Paper feed tray 4) 1)

Remove the 3/4 paper feed drive unit. (See “(1) 3/4 paper feed drive unit”)

2)

Remove the 3/4 drive frame lower. (See “a. Paper feed clutch (Paper feed tray 3)”)

3)

Disconnect the connector, and remove the paper feed clutch unit.

MX-M700N DRIVE SECTION P – 12

5)

(2)

Remove the E-ring, and remove the paper feed tray 3/4 and the paper transport clutch 1.

3)

Release the pawl, and remove the lift-up coupling. Remove the lift-up spring from the lift-up motor.

Others

a. Paper tray lift-up motor (Paper feed tray 3) b. Paper tray lift-up motor (Paper feed tray 4) 1)

Remove the rear cabinet.

2)

Disconnect the connector, and remove the paper tray lift-up motor (paper feed tray 3) (A) and the paper tray lift-up motor (Paper feed tray 4) (B).

A

B

MX-M700N DRIVE SECTION P – 13

2. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.) 55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Drive section

No. 1 2 3 4 5 6

Part name Gears (grease) Gears (grease) Gears (grease) Gears (grease) Gear (Conductive grease) Belts

✕ ✕ ✕ ✕ ✕

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

✩ ✩ ✩ ✩ ✩ ✕

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

UKOG-0307FCZZ UKOG-0299FCZZ UKOG-0062FCZZ UKOG-0235FCZZ UKOG-0012QSZZ

4

3 3

2 2

1 1 1 1

1 1

1

5

1

1

2 1

1 2

6

MX-M700N DRIVE SECTION P – 14

2

MX-M700N

[Q] PWB SECTION

5GTXKEG/WCN

1. Disassembly and assembly

2)

Disconnect the connector, and remove the PCU PWB.

A. Control PWB section No. (1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

Parts PCU FLASH PWB PCU PWB Driver PWB Mother PWB Controller cooling fan motor HDD cooling fan motor HDD Soft NIC PWB MFP FLASH ROM PWB MFP controller PWB

(3)

Driver PWB

1)

Remove the rear cabinet and the rear cabinet upper.

2)

Disconnect the connector, and remove the harness clamp and the SCAN harness cover.

3)

Remove the connector and the harness clamp. Remove the driver PWB unit.

(6) (7)

(4)

(10)

(1)

(8)

(3) (5)

(9)

(2)

(1) 1)

(2) 1)

PCU FLASH PWB Remove the ROM cover. Release the lock and remove the PCU Flash PWB.

PCU PWB Remove the rear cabinet.

MX-M700N PWB SECTION Q – 1

4)

(4)

(5)

Remove the driver PWB.

Mother PWB

1)

Remove the driver PWB unit. (See “(3) Driver PWB”)

2)

Remove the harness, and remove the mother PWB stay.

Controller cooling fan motor

1)

Remove the driver PWB unit. (See “(3) Driver PWB”)

2)

Disconnect the connector and remove the harness clamp. Remove the controller cooling fan motor unit.

3)

Remove the controller cooling fan motor.

Flow direction

Mark

Fan blowing direction

* When assembling, fit the mark with the fan flow direction.

(6) 3)

4)

Disconnect the connector and remove the mother PWB unit.

HDD cooling fan motor

1)

Remove the rear cabinet and the rear cabinet upper. (See “(3) Driver PWB”)

2)

Disconnect the connector, and remove the harness clamp.

3)

Disconnect the connector, and remove the HDD cooling fan motor.

Remove the mother PWB.

Flow direction

Mark

Fan blowing direction

* When assembling, fit the mark with the fan rotating direction. MX-M700N PWB SECTION Q – 2

(7)

HDD

1)

Remove the cooling fan motor unit. (See “(5) Controller cooling fan motor”)

2)

Disconnect the connector, and remove the HDD unit.

3)

3)

Remove the soft NIC PWB unit.

4)

Remove the soft NIC PWB angle from the soft NIC PWB.

Remove the HDD slide plate, and remove the HDD mounting plate from the HDD.

(9) (8) 1)

Soft NIC PWB

MFP FLASH ROM PWB

1)

Pull out the NIC control unit. (See “(8) Soft NIC PWB”)

2)

Release the lock, and remove the MFP Flash PWB.

Remove the right cabinet upper.

(10) MFP controller PWB 2)

Pull out the NIC control unit.

1)

Remove the manual feed cover F, the right cabinet middle, and the right cabinet upper. (See “(8) Soft NIC PWB”)

2)

Pull out the NIC control unit, and remove the flat cable. Release the lock, and remove the NIC control unit.

MX-M700N PWB SECTION Q – 3

3)

B. Power section

Remove the soft NIC PWB unit.

No. (1) (2) (3) (4) (5) (6) (7)

Parts AC power PWB DC main power PWB Power cooling fan motor 1 Power cooling fan motor 2 Dehumidifier heater relay PWB DC sub power PWB High voltage PWB (MC/DV/TC)

(6)

4)

Remove the PWB protection plate. Remove the MFP controller PWB.

(2)

(7)

(1) (3) (5)

(1)

(4)

AC power PWB

1)

Remove the rear cabinet.

2)

Disconnect the connector, and remove the AC power PWB.

MX-M700N PWB SECTION Q – 4

(2)

DC main power PWB

3)

Remove the AC/DC power unit.

4)

Remove the AC power PWB unit.

5)

Remove the DC power PWB unit.

(Method 1) 1)

Remove the rear cabinet. (See “(1) AC power PWB”)

2)

Disconnect the connector and remove the harness clamp. Remove the AC power PWB unit.

3)

Disconnect the connector and remove the DC main power PWB.

(Method 2) 1)

Remove the rear cabinet. (See “(1) AC power PWB”)

2)

Remove the connecter.

MX-M700N PWB SECTION Q – 5

(3)

Power cooling fan motor 1

(6)

(4)

Power cooling fan motor 2

1)

Remove the paper exit tray cabinet.

2)

Disconnect the connector and remove the er. Remove the DC sub power PWB.

1)

Remove the rear cabinet. (See “(1) AC power PWB”)

2)

Disconnect the connector, and remove the AC power PWB unit. (See “(2) DC main power PWB”)

3)

Disconnect the connector and remove the harness clamp. Remove the power cooling fan motors 1/2.

DC sub power PWB

REVERSE

Mark

Mark

Fan blowing direction

* When assembling, fit the mark with the fan rotating direction. (label on the back surface)

(5)

Dehumidifier heater relay PWB

1)

Remove the rear cabinet. (See “(1) AC power PWB”)

2)

Disconnect the connector and remove the er. Remove the dehumidifier heater relay PWB.

(7)

High voltage PWB (MC/DV/TC)

1)

Remove the rear cabinet. (See “(1) AC power PWB”)

2)

Disconnect the connector and remove the earth terminal. Remove the high voltage PWB.

MX-M700N PWB SECTION Q – 6



MX-M700N [R] FAN AND FILTER SECTION

5GTXKEG/WCN

1. Disassembly and assembly

3)

Disconnect the connector, and remove the DV fan.

A. Fan motors No. (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

Parts Developing section cooling fan motor Paper cooling fan motor Fusing cooling fan motor 2 Process exhaust fan motor 5 Process exhaust fan motor 4 Process exhaust fan motor 1 Process exhaust fan motor 2 Process exhaust fan motor 3 Process cooling fan 1 Process cooling fan 2 Process cooling fan 3

Fan blowing direction

(2) (3) (6) (7) (8)

1)

2)

Remove the rear cabinet and the rear cabinet upper.

2)

Disconnect the connector, and remove the paper cooling fan motor.

(2) (4)

(9) (10) (11)

(1)

Paper cooling fan motor

1)

(5) (1)

Developing section cooling fan motor Remove the rear cabinet.

Disconnect the connector and remove the harness clamp. Remove the DV fan unit.

Fan blowing direction

* When installing, arrange so that the arrow mark on the side of the duct faces in the same direction with the arrow mark on the side of the fan.

MX-M700N FAN AND FILTER SECTION R – 1

(3) 1)

Fusing cooling fan motor 2

6)

Disconnect the connector, and remove the paper exit rear duct unit.

7)

Disconnect the connector, and remove the fusing cooling fan motor.

Remove the rear cabinet. (See “(1) Developing cooling fan motor”)

2)

Remove the tray.

3)

Remove the left cover cabinet.

REVERSE

Fan blowing direction

4)

Open the left door.

* Be careful of the direction of the fan.

(4) Process exhaust fan motor 5 1)

Remove the rear cabinet.

2)

Disconnect the connector and remove the harness clamp.

(See “(1) Developing cooling fan motor”) Remove the sub duct unit.

5)

Remove the left cabinet upper. 3)

Disconnect the connector and remove the process exhaust fan motor 5.

Fan blowing direction

* Be careful of the direction of the fan.

MX-M700N FAN AND FILTER SECTION R – 2

(5)

Process exhaust fan motor 4

1)

Remove the rear cabinet.

2)

Remove the sub duct unit.

3)

Disconnect the connector and remove the process exhaust fan motor 4.

5)

Remove the right cabinet upper.

6)

Remove the front cabinet band, and remove the front cabinet.

7)

Remove the toner bottle. (See “(1) Toner bottle unit” in the “Toner hopper and toner bottle section”)

8)

Remove the toner hopper unit. (See “(2) Toner hopper unit” in the “Toner hopper and toner bottle section”)

9)

Remove the developing unit.

(See “(1) Developing cooling fan motor”) (See “(4) Process exhaust fan motor 5”)

Marks

REVERSE

Fan blowing direction

* When assembling, fit the mark with the fan rotating direction. (label on the back surface)

(6)

Process exhaust fan motor 1

(7)

Process exhaust fan motor 2

(8)

Process exhaust fan motor 3

1)

Remove the DSPF unit.

2)

Remove the scanner unit.

3)

Pull out the multi paper feed tray unit, and remove the manual paper feed cover F.

4)

Remove the right cabinet middle.

(See “A-(1) DSPF unit” in the “DSPF section”)

(See “(1) Developing unit” in the “Developer tank section”) 10) Remove the process unit.

(See “(1) Scanner unit” in the “Scanner section”)

(See “A-(1) Process unit” in the “OPC drum section”) 11) Raise the process DV cover diagonally, and remove the front right cover.

12) Remove the front cabinet upper.

MX-M700N FAN AND FILTER SECTION R – 3

13) Remove the paper exit tray cabinet unit.

17) Disconnect the connector, and remove the process cooling fan motors 1 (A), 2 (B), and 3 (C).

REVERSE

Marks Mark

14) Remove the paper exit port cabinet, and remove the paper exit tray cabinet C.

A B C Fan blowing direction

* When assembling, fit the mark with the fan rotating direction. (label on the back surface)

(9)

Process cooling fan motor 1 (LSU, process section)

(10) Process cooling fan motor 2 (LSU, process section) 15) Disconnect the connector and remove the harness clamp. Remove the main duct unit.

(11) Process cooling fan motor 3 (LSU, process section) 1)

Pull out the multi paper feed tray, and remove the manual paper feed cover F.

2)

Pushing the lower part, remove the right cabinet center.

16) Remove the fan unit.

MX-M700N FAN AND FILTER SECTION R – 4

3)

Disconnect the connector, and remove the process cooling fan unit.

B. Filters No. (1) (2) (3)

Parts Ozone filter DV ozone filter Toner filter

(1) 4)

Disconnect the connector, and remove the process cooling fan motors 1 (A), 2 (B), and 3 (C).

(2) (3) RE

VE

RS E

Marks

Mark

(1)

Ozone filter

1)

Remove the rear cabinet.

2)

Release the pawl, and remove the ozone filter.

A B C Fan blowing direction

* When assembling, fit the mark with the fan rotating direction. (label on the back surface)

MX-M700N FAN AND FILTER SECTION R – 5

(2) (3)

DV ozone filter Toner filter

1)

Remove the rear cabinet. (See “(1) Ozone filter”)

2)

Remove the DV filter box.

3)

Remove the DV ozone filer (A) and the toner filter (B).

A

B

2. Maintenance ✕: Check

{: Clean

▲: Replace

U: Adjust

✩: Lubricate

†: Shift position

(Clean, replace, or adjust according to necessity.)

55ppm (PM: 250K) When calling 62ppm/70ppm (PM: 300K) Unit name Filters

No. 1 2

Part name Ozone filter Toner filter

250 K

500 K

750 K

1000 K

1250 K

1500 K

1750 K

2000 K

300 K

600 K

900 K

1200 K

1500 K

1800 K

2100 K

2400 K

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

▲ ▲

1

1 2

MX-M700N FAN AND FILTER SECTION R – 6

Remark/Refer to the Parts Guide. Block/Item No. (Only the replacement parts are described.)

(P/G No.: [75]-7) (P/G No.: [75]-8)

MX-M700N

[S] SENSOR, SWITCH SECTION

5GTXKEG/WCN

1. Disassembly and assembly

7)

Disconnect the connector, and remove the power switch.

A. Sensors and switches No. (1) (2) (3) (4) (5) (6)

Parts Power switch Main power switch Front door open/close detector Left door open/close detector Dry heater switch Machine temperature sensor

(2) (3)

* When installing, be careful of the connector connecting position and the installing direction. Also be careful not to break the SW pawl.

(6) (1)

(4) (5)

(1)

Power switch

(2)

Main power switch

(3)

Front door open/close detector

1)

1

4

6

2

5

7

Remove the front cabinet band, and remove the front cabinet.

3

8

[Connector connecting position] Connector color Line color 1 Yellow Black 2 White Black 3 Blue Black 4 White Red 5 White Brown 6 Yellow White 7 White White 8 Blue White

Power switch (Connector surface)

8)

2)

Remove the toner bottle. (See “(1) Toner bottle unit” in “[Toner hopper and toner bottle section]”)

3)

Remove the toner hopper unit. (See “(2) Toner hopper unit” in “[Toner hopper and toner bottle section]

4)

Remove the developing unit. (See “(1) Developing unit” in the “[Developer tank section]”)

5)

Remove the process unit. (See “A-(1) Process unit” in the “[OPC drum section]”)

6)

Raise the process DV cover diagonally, and remove the front right cover.

Disconnect the connector, and remove the main power switch unit.

* When installing, be careful of the connector connecting position and the installing direction. Also be careful not to break the SW pawl. [Connector connecting position] Connector color Line color 1 White Black 2 Black Black 3 White White 4 Black White

1

3

2

4

Main power switch (Connector surface)

MX-M700N SENSOR, SWITCH SECTION S – 1

9)

Remove the main power switch.

10) Remove the counter mounting plate.

2)

Remove the left front cabinet.

3)

Disconnect the connector, and remove the left door open/close detector unit. Remove the left door open/close detector.

11) Disconnect the connector and remove the front door open/ close switch unit.

(5)

(4) 1)

Dry heater switch

1)

Remove the rear cabinet.

2)

Disconnect the connector, and remove the dry heater switch.

Left door open/close detector Open the left door.

MX-M700N SENSOR, SWITCH SECTION S – 2

(6)

Room temperature sensor

1)

Pull out the multi paper feed tray, and remove the manual paper feed cover F.

2)

Pushing the lower part, remove the right cabinet center.

3)

Disconnect the connector, release the pawl, and remove the machine temperature sensor.

MX-M700N SENSOR, SWITCH SECTION S – 3

LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder.

Example: <Solder composition code of lead-free solder>

Lead-Free

5mm

Solder composition code (Refer to the table at the right.)

a

Solder composition

Solder composition code

Sn-Ag-Cu

a

Sn-Ag-Bi Sn-Ag-Bi-Cu

b

Sn-Zn-Bi

z

Sn-In-Ag-Bi

i

Sn-Cu-Ni

n

Sn-Ag-Sb

s

Bi-Sn-Ag-P Bi-Sn-Ag

p

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident. Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

©

Since the melting point of lead-freeCOPYRIGHT solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering XXXX BYSHARP CORPORATION capacity is inferior to conventional one, it is apt to keep the soldering iron in with the PWB for longer time. This may cause land separation or may exceed the heat-resistive temperature components. Use enough care to separate the soldering iron from the PWB when ALLofRIGHTS RESERVED. completion of soldering is confirmed. Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently. If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after completion of soldering work. No part of this publication may be reproduced, in a retrieval transmitted If the soldering iron tip is discolored black stored during soldering work,system, clean andorfile the tip with in steel wool or a fine filer.

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions. (Finnish) VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (French) ATTENTION Il y a danger d’explosion s’ il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (Swedish)

VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

(German) Achtung Explosionsgefahr bei Verwendung inkorrekter Batterien. Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder vom Hersteller empfohlene Batterien verwendet werden. Entsorgung der gebrauchten Batterien nur nach den vom Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY DISPOSAL (For USA, CANADA) “BATTERY DISPOSAL” THIS PRODUCT CONTAINS A LITHIUM PRIMARY (MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE BATTERY FROM THE PRODUCT AND YOUR LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND DISPOSAL OPTIONS. “TRAITEMENT DES PILES USAGÉES” CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE) QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA PILE DU PRODUIT ET PRENEZ AVEC VOTRE AGENCE ENVIRONNEMENTALE LOCALE POUR DES INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET DE TRAITEMENT.

COPYRIGHT © 2007 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher.

Trademark acknowledgements Microsoft® Windows® operating system is a trademark or copyright of Microsoft Corporation in the U.S.A. and other countries. Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows® 2000 Server, Windows® Server 2003 and Internet Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries. IBM and PC/AT are trademarks of International Business Machines Corporation. Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated. All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION Digital Document System Group CS Promotion Center Yamatokoriyama, Nara 639-1186, Japan 2007 February Printed in Japan