Seaward Apollo Manual V2 V2 5f3p6e

Apollo 600 Table of Contents 1. Limited Warranty & Limitation of Liability 2. Disposal of old product 3. Certificate of Conformity 4. Notes 5. Safety Notes 6. Accessories 6.1 Standard accessories 6.2 Optional Accessories

7. Introduction to the Apollo 600 7.1 Front diagram 7.2 Top Diagram 7.3 Back diagram

8. Getting Started 8.1 Charging New Batteries 8.2 Power On

9. Interface Navigation 9.1 Screen Layout 9.2 Menu Navigation 9.3 Battery Status 9.4 Test Functionality

10. Main Menu 10.1 View Saved Data 10.2 Options 10.3 Bluetooth Setup 10.4 Automatic Test Sequence Editor (PAT Edit) 10.5 10.5.1 ing into PATGuard 3 10.6 10.6.1 ing from PATGuard 3 10.6.2 ing a Logo for TnT Labels 10.7 Set Date and Time 10.8 Memory

11. Portable Appliance Testing 11.1 Automatic Test Sequence 11.1.1 Entering Asset Details 11.1.2 Using the Risk Based Retest Period Calculator 11.1.3 The Formal Visual Inspection 11.2 Manual Test Interface 11.3 Test Functions Earth Continuity Nulling out Test Leads Insulation Resistance

Substitute Leakage Protective Earth (PE) Conductor Current Touch Current RCD Trip Time IEC Lead / Polarity External Leakage Adaptors 11.4 Checkbox Verification 11.5 PAT Settings

12. Universal Risk Assessment 13. Health & Safety Reports 14. Updating your Firmware 15. Electrical Specification 16. Useful Information 16.1 Factory Set Test Sequences 16.2 Other Information

17. Environmental Conditions 18. Maintenance 18.1 Charging the battery pack. 18.2 Securing the Apollo 600 18.3 Cleaning the Apollo 600 18.4 Replacing the battery pack

19. 19.1 Registration 19.2Calibration

1. Limited Warranty & Limitation of Liability SEAWARD Electronic Limited guarantees this product to be free from defects in material and workmanship under normal use and service for a period of 2 years (subject to product registration) provided that the instrument is serviced and calibrated by a Seaward approved agent in accordance with the manufactures instructions. The period of warranty will be effective at the day of delivery. (c) Copyright 2013 All rights reserved. Nothing from this edition may be multiplied, or made public in any form or manner, either electronically, mechanically, by photocopying, recording, or in any manner, without prior written consent from SEAWARD Electronic Limited. This also applies to accompanying drawings and diagrams. Due to a policy of continuous development SEAWARD Electronic Limited reserves the right to alter the equipment specification and description outlined in this publication without prior notice and no part of this publication shall be deemed to be part of any contract for the equipment unless specifically referred to as an inclusion within such contract.

2. Disposal of old product This product has been designed and manufactured with high quality materials and components that can be recycled and reused. When this symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

Please familiarise yourself with the appropriate local separate collection system for electrical and electronic products. Please dispose of this product according to local regulations. Do not dispose of this product along with normal waste material. The correct disposal of this product will help prevent potential negative consequences for the environment and human health.

3. Certificate of Conformity As the manufacturer of the apparatus listed, declare under our sole responsibility that the product:

Apollo 600 To which this declaration relates are in conformity with the relevant clauses of the following standards:

BS EN 61010-1:2010, BS EN 61010-1-030:2010, BS EN 61010-031:2008 Safety requirements for electrical equipment for measurement, control, and laboratory use. BS EN 61557-1,-2,-4:2007 & -10:2001 Electrical safety in low voltage distribution systems up to 1000V a.c. and 1500V d.c. – Equipment for testing, measuring and monitoring of protective measures BS EN 61326:2006 Electrical equipment for measurement, control and laboratory -EMC Requirements Performance: The instrument operates within specification when used under the conditions in the above standards EMC and Safety Standards. The product identified above conforms to the requirements of Council Directive 89/336/EEC and 73/23 EEC. Seaward Electronic Ltd is ed under BS EN ISO9001:2000 Certificate No: Q05356.

4. Notes These operating instructions are intended for the use of adequately trained personnel. The following symbols are used in these operating instructions and on the Apollo 600. Warning of electrical danger! Indicates instructions must be followed to avoid danger to persons. Caution, follow the documentation! This symbol indicates that the operating instructions must be adhered to in order to avoid danger. Note: Data may be lost or altered in virtually any electronic memory under certain circumstances. Therefore Seaward Electronic assumes no responsibility for financial losses or claims due to data lost or otherwise rendered unusable whether as a result of abuse, improper use, defects, disregard of operating instructions or procedures, or any allied causes.

5. Safety Notes This Apollo 600 has been built and tested in accordance with: BS EN 61010-1: 2010. BS EN 61557 part 1, 2, 4 and 10. To ensure safe operation of the unit, all notes and warnings in these instructions must be observed at all times. If the Apollo 600 is used in a manner not specified by these operating instructions then the protection provided may be impaired. Always ensure that the circuit or appliance under test is electrically isolated. Do not connect the Apollo 600 to electric circuits with nominal voltage greater than CAT II 300 V AC/DC. The Apollo 600 and all associated cables and leads must be checked for signs of damage before equipment is operated. Do not use if there are signs of damage. Only use the correct leads supplied with the Apollo 600. Do not touch test probes beyond the hand barrier on the test probe. The Apollo 600 may apply high voltage or mains power to the appliance under test. Do not touch conductive parts of the appliance while tests are active. If the Apollo 600 is being used to determine the presence or absence of hazardous voltages, always prove the operation of voltage measurement function before and after use by means of a known voltage source or proving unit. Do not operate the Apollo 600 in an explosive gas or dust environment. The Apollo 600 has been designed to make measurements in a dry environment.

The Apollo 600 includes a rechargeable battery pack which is charged while the Apollo 600 is connected to a mains supply. Only a Seaward battery pack should be connected into the Apollo 600. Disconnect the Apollo 600 from all leads before opening the battery compartment. Do not open the Apollo 600, no serviceable parts.

Where safe operation of the Apollo 600 is no longer possible it should be immediately shut down and secured to prevent accidental operation. It must be assumed that safe operation is no longer possible: - if the instrument or leads show visible signs of damage or - the instrument does not function or - after long periods of storage under adverse environmental conditions.

6. Accessories 6.1 Standard Accessories The Apollo 600 is supplied with the following items: Apollo 600 unit Professional carry case Seaward black power lead Test lead, black, 1.2m Alligator clip, black Test lead, red, 1.2m Alligator clip, red IEC test lead Test adaptor, 110V/230V USB Lead Apollo 600 Check Box

1 1 1 1 1 1 1 1 1 1 1

6.2 Optional Accessories Test n Tag Elite Bluetooth Label Printer Bluetooth Barcode Scanner PATGuard 3 Software 3 Phase Leakage Adaptor 5 Star 16A 3 Phase Leakage Adaptor 5 Star 32A 3 Phase Adapter Delta 4 pin 16A 415V (for Rpe & IR) 3 Phase Adapter Star 5 pin 16A 415V (for Rpe & IR) 3 Phase Adapter Delta 4 pin 32A 415V (for Rpe & IR) 3 Phase Adapter Star 5 pin 32A 415V (for Rpe & IR)

339A970 339A923 see www.seaward.co.uk/PG3Trial 391A920 391A910 209A910 209A911 209A912 209A913

7. Introduction to the Apollo 600 Front 1. Test terminal end plate 2. LCD 3. Function keys 4. QWERTY keyboard 5. Test function STOP key 6. Test function START key 7. Arrow keys

Top 1. EUT test socket 2. IEC test socket 3. Red test terminal 4. Black test terminal 5. USB type B 6. USB type A

Back 1. Camera Lens 2. Flash source 3. Battery compartment

8. Getting Started 8.1 Charging New Batteries Before using Apollo 600 for the first time please ensure that you fully charge the unit using the Seaward black power lead plugged into the mains inlet socket on the top of the tester.

8.2 Power On This is the Power On button.

This is the Power Off button

The first time the Apollo 600 is powered up the will be automatically set to . The gives full access to all the menus and functionality of the unit. For further information about changing and see 10.2 Options.

9. Interface Navigation 9.1 Screen Layout 1. Information bar 2. Function key icons 3. Test interface sequence table 4. Test interface details 5. Main area

Information Bar This area of the screen shows the Date, Time, Current , Battery Status and Connection Status. Function Key Icons This area of the screen is used to identify the current action assigned to the function keys. Test Interface Sequence Table This area is only displaying in test mode showing the tests within the selected test sequence. This will also show the results and status of the results that have been performed. In the manual mode this table may only show one test. Test Interface Details This area is only displayed in test mode showing the details specific to the active test. This includes the measurement, an analogue measurement graph, the duration and limit. Some tests may show more than more measurement. Main Area This area is used to display menu items, text fields and forms.

9.2 Menu Navigation The Apollo is controlled by the function keys. The function key icons, which are located above each key, are context sensitive and will change depending on the current options available to you. This is the Home function. This will take you back to the Home screen.

This is the Escape function. This will return to the previous screen without saving changes. This is the Accept function. This will accept the changes made in the current screen and move to the next screen. This is the Setup Options function. This will take you the Setup Options screen for the specific function that you are currently viewing. This is the information key. Depending on the current screen displayed this will display the manual or the Apollo 600 details, in the details screen this function will

display the manual. This is the Menu/Options key. This function will bring up a context sensitive menu giving the options available for the current screen. This is the Save key. This function is used to save data/changes that you have made on the current screen. This is the camera function. This function will appear when you are able to take photographs.

9.3 Battery Status While the Apollo 600 is powered on there are periodic checks of the batteries. The Apollo 600 will show the status of the batteries This symbol indicates that the batteries are at 100% capacity. There are several symbols which will display the current battery voltage. When these icons are displayed the batteries are still good. This symbol indicates that the batteries are low. Although tests performed with the batteries in this state are still valid all test types may not complete their intended duration. This symbol indicates that the batteries are discharged. The Apollo 600 will switch itself off after a short period of time. This symbol indicates that the Apollo 600 is bulk charging batteries at the full charge current. This symbol indicates that the Apollo 600 is trickle charging the batteries with reduced charge current. This is known as the Top Up Charge. This symbol indicates that the Apollo 600 has detected a fault with the battery or battery charger circuit. Unplug the Apollo 600 from the mains supply and wait 2 minutes before reconnecting the mains. If the fault persists then return the Apollo 600 for service. Please note that the battery symbols are not updated in real time and may take a while to update.

9.4 Test Functionality There are two buttons which control the starting and stopping of the selected test type. This is the Start Test button. This is used to start electrical tests.

This is the Abort Test button. This is used to stop electrical tests.

10. Main Menu 10.1 View Saved Data This will allow you to view any data that you have saved in the Apollo 600. By selecting this icon in the Main Menu you can view a list of all saved Asset IDs by site and location. Use the arrow keys to scroll up and down. This is the Accept function. This will open the selected record.

This button allows you to filter records to give a customised view. Select the filters you wish to apply and press ‘Accept’. Once in the record you will be given a list of items under that record such as PAT results and JPEG images. Press Accept to open. When viewing a PAT_results record the Menu icon will become available so that you can view results or print labels. When viewing a saved Health & Safety Form you can edit the report and then save the changes. This will create a new time and date stamped report as well as saving the original. This is the Menu/Options key. This function will bring up a context sensitive menu giving the options available for the current screen.

10.2 Options Apollo 600 has one default set up as who will have full access to the product. This is where you can set up new, edit and delete s. s can alter their own screen power save time, Auto power down, background image, avatar and power on screen and press Save to apply. Use this button to Change . You can then select the name and enter the correct to change the current of the tester. You can also change the of the current by selecting ‘change ’ and entering the old and entering a new one then confirming it. Use this button to Change of the current by selecting ‘change ’ and entering the old and entering a new one then confirming it. This Privileges menu allows s to view their current privileges. If they have ‘Edit s’ rights they will also be able to edit their own and other s privileges by selecting the they wish to edit from the dropdown. This is the New button. Here you can set up a new by adding a name and and pressing ‘Save. You can then select their name from the dropdown in the Privileges screen, select the type of (Expert or Novice) and set up their privileges by pressing the Enter key to check or uncheck. If a privilege is checked, the has access to that feature or function. To block a feature or function, e.g. adjusting the time and date or editing test sequences, uncheck that function before saving.

This is the Delete button. It will delete whichever is currently selected in the ‘name’ dropdown. Please note that the cannot be deleted. Press this button to Save changes and return to the previous screen.

This is the Copy function. This will copy the settings and preferences of the current to a new .

10.3 Bluetooth Setup Select this icon to setup your Bluetooth accessories to work with the Apollo 600. Switch on the Bluetooth device you wish to pair with and ensure it is discoverable. This will Bluetooth Search button will search the area for Bluetooth discoverable devices and return to the previous menu. You can then use the arrow keys to select the correct Bluetooth ID from the dropdowns for your Bar Code Scanner, Printer or Mobile Device. Press ‘Save’ once complete. Press this button to save changes and return to the previous screen.

10.4 Automatic Test Sequence Editor (PAT Edit) Although the Apollo 600 comes with a number of pre-defined test sequences you can modify existing, or create new test sequences of their own. From the Menu function key select one of the following options using the arrow keys and the Accept button. This is the Menu/Options key. This function will bring up a context sensitive menu giving the options available for the current screen. This is the Accept function. This will open the selected option.

Edit

Edits the highlighted sequence.

Copy

Makes a copy of the highlighted test sequence.

Delete

Deletes the highlighted test sequence.

Add New

Adds a new test sequence to the bottom of the list.

Insert New

Adds a new test below the highlighted test sequence.

When editing a test sequence the following functions are available This is the Add Test function. This will add a new test directly under the currently selected test. This is the Delete Test function. This will delete the highlighted test from the test

sequence. This is the Edit Test function. This will edit the highlighted test.

10.5 10.5.1ing to PATGuard 3 You can the data from your Apollo to PATGuard 3 software. In the menu select To PATGuard in the data from Apollo dropdown. This button allows you to filter records for . Select the filters you wish to apply and press Accept. This is the Accept function. This will accept the changes made in the current screen and move to the next screen. You then need to select one of 3 options from the using dropdown:

Flash Memory Stick Insert a USB flash memory stick into the USB type A port on the Apollo 600. Press ‘Save’. Instructions for how to import this into PATGuard 3 can be found in the PATGuard 3 help files.

USB-PC cable Connect the USB cable to the USB type B port on the Apollo 600 and to a USB port on your PC. Press Save. Instructions for how to import this into PATGuard 3 can be found in the PATGuard 3 help files.

Bluetooth to Mobile Device You will need to have a Bluetooth enabled mobile device configured with the Apollo 600 to use this method. See 10.3 Bluetooth Setup.

10.6 10.6.1 ing from PATGuard 3 ing of records from PATGuard 3 is not available in this firmware version. Please go to www.seaward.co.uk/firmware to the latest Apollo 600 firmware file. See 14. Updating Your Firmware section. 10.6.2 ing a Logo for TnT Labels A bitmap logo can be transferred to the Apollo 600 for use with the Seaward Test ‘n’ Tag print system. The logo must be in .BMP with a maximum size of 320 pixels by 240 pixels. Save the logo you wish to use onto a USB memory stick. In the menu select Printer Logos from the data into Apollo dropdown. Select Flash Memory Stick in the using dropdown. Insert the USB memory stick. Press the Save button to save the logos to the Apollo 600. See Printing a Label.

10.7 Set Date and Time You can change the date and time in this menu using the arrow keys and number keys. Press this button to save changes and return to the previous screen.

10.8 Memory This section will allow you to view how much memory space you have used and how much is left. This is the Restore button. Selecting this will allow you to clear memory or reset factory settings. Select what you would like to restore by pressing the Enter button. Press this button to save changes and return to the previous screen.

11. Portable Appliance Testing 11.1 Automatic Test Sequence The Apollo 600 comes with a number of pre-defined test sequences (see 16.1 Factory Set Test Sequences). These test sequences can include any combination of electrical or defined tests. These test sequences are performed on equipment to ensure that it meets the safety requirements outlined in the IET Code of Practice for In-service Inspection and Testing of Electrical Equipment. 11.1.1 Entering Asset Details Asset ID

This is unique identifier for the equipment under test. This can be entered using the keypad, a barcode scanner (see 10.3 Bluetooth Setup), or set to automatically increment (see 11.4 PAT Settings).

Test Sequence

This is the name of the pre-defined test sequence which will be performed on the equipment.

Site

This is the site where the equipment is located. You can choose a site from the dropdown using the arrow keys or enter a new one.

Location

This is the location within the site where the equipment is. You can choose a location from the dropdown using the arrow keys or enter a new one.

Retest Period (Visual)

This is the period, in months, in which the equipment should be reinspected. This can be completed manually or the ‘Risk Based Retest Period Calculator’ can be used.

Retest Period (Full) This is the period, in months, in which the equipment should be retested. This can be completed manually or the ‘Risk Based Retest Period Calculator’ can be used.

You can use the Camera function to attach photos to the asset record.

This button will enable and disable the flash light. Press this button to take the picture.

This button will attach the picture and go back to the record. To add another picture press the ‘Camera’ button again. This button will cancel the picture and allow you to take another.

11.1.2 Using the Risk Based Retest Period Calculator The Risk Based Retest Period Calculator will allow you to select options using the arrow keys from the dropdowns. It will then determine if the asset is Low or High risk and advise retest periods for Formal Visual and Full Test. This is the Accept function. This will accept the changes made in the current screen and move to the next screen. 11.1.3 The Formal Visual Inspection All preset test sequences start with a Visual Inspection. Using the Camera in this screen will tag the picture to the test result. This is the Icon.

This is the Fail icon. This means that the inspection is not applicable to the EUT.

Pressing the All button will apply a to all relevant inspections and move All onto the next test. 11.1.4 The Electrical Tests The Apollo 600 has probe detection that will automatically flag up if you do not have the correct probe configuration for the test you are trying to perform. During the tests you can see the test duration, limit and result on screen, see 9.1 Screen Layout. Should any test with the sequence fail the sequence will be aborted and you will presented with the Notes screen by default but this can be changed, see 11.5 PAT Settings. 11.1.5 Printing a Label If you have a TnT Bluetooth printer configured with the Apollo 600 you can set it to automatically print a label after each test.

In PAT Settings set After Test to Print Label and press Save. See 10.3 Bluetooth Settings & 11.5 PAT Settings. This is the Tools function. This function allows you to configure the label Title, select a or Fail Logo, change print density and select which pre-configured label printer to use. This is the Change Format function. This will change the format of the label

11.2 Manual Test Interface The Apollo 600 allows direct access to all of the electrical tests through Manual Mode. Within each test there are a number of function key options; This is the Tools function. This function allows you to configure the test current test type, this includes; - test duration - test /fail limit - test type/connection Always ensure that you have selected the correct test connection method in the test for the probe connections made. Please refer to the Test Functions section for specific information about each test type.

11.3 Test Functions Earth Continuity Always ensure that the circuit under test is electrically isolated. Note that measurements can be adversely affected by parallel resistances of additional circuits or by transient currents. Connecting a test probe to a hazardous voltage when a point to point measurement is active will result in that voltage being present on the other test probe. This test is applicable to Class I equipment. This test will measure one of the following: resistance between the protective earth terminal in the EUT mains plug and the point at which a single test probe is applied – CLI EUT Continuity • resistance between two test probes – Point to Point Continuity • resistance between the protective earth terminal in an IEC lead mains plug and the protective earth terminal in the IEC connector – IEC Continuity to ensure that the connection is satisfactory and of sufficiently low resistance. The measurement will be displayed in Ohms. There are three possible connection methods for the Earth Continuity test. •

CLI EUT Continuity The test is performed between the red test terminal and the EUT test socket.

Point to Point Continuity This test is performed between the red test terminal and the black test terminal.

IEC Continuity The test is performed between the EUT test socket and the IEC test socket.

Always ensure that you have selected the appropriate test type for the probe connections. Selecting test type In manual PAT test mode, the earth continuity test can be switched between a Class I EUT continuity test and a point to point continuity test as follows: Select Class I Continuity (1) and press the setup key (F3). In the Test Type field, select EUT Continuity Test or Point to Point Continuity Test. During automatic sequences, the test type will be as per the test type programmed in the test sequence. Once the correct connections have been made for the selected test type press the Start button. The test will continue until it times out. If we wish to abort the current test press the Stop button. Tests on IEC leads, CLI EUTs can be performed using a current of +200mA and/or -200mA. Tests performed in point to point mode are always performed using a current +200mA test. The direction of the test current can be reversed by switching the test probes at the point of connection to the appliance/circuit under test. Nulling out the earth continuity test lead(s) resistance For a more accurate earth continuity measurement, the resistance of the test lead(s) can be zeroed out. The feature can be used with both the EUT Continuity and Point to Point measurement modes. The null facility remains active, even if the Apollo 600 is powered off, until the feature is deactivated by pressing the null key again or the Test Type is changed e.g. if a pair of test leads are nulled for point to point measurement, the null will be deactivated if the Test Type is changed to EUT Continuity test.

Nulling a single test lead In the manual PAT screen, press the setup key (F3) and change the Test Type to EUT Continuity Test. Press save (F4). Connect the earth continuity test lead to the earth continuity test socket and connect the probe tip to the earth pin of the EUT socket. Press Null (F4) to measure and stored the test lead resistance. When the null feature is active the Null icon will appear on the display. Nulling both test leads In the manual PAT screen, press the setup key (F3) and change the Test Type to Point to Point Continuity Test. Press save (F4). Connect both earth continuity test leads to the earth continuity test sockets and connect the probe tips together using the supplied alligator clips. Press Null (F4) to measure and stored the test lead resistance. When the null feature is active the Null icon will appear on the display.

Insulation Resistance Always ensure that the circuit under test is electrically isolated. Connecting a test probe to a hazardous voltage when a point to point measurement is active will result in that voltage being present on the other test probe. This test is applicable to Class I and Class II equipment. This test will measure one of the following: • • •

insulation resistance between live circuits and the protective earth circuit in the EUT – Class I / IEC lead insulation test insulation resistance between live circuits and a test probe applied to the EUT – Class II insulation test insulation resistance between two test probes – Point to Point Insulation

to ensure that the test points are adequately insulated from one another. The measurement is displayed in MOhms. There are three possible connection methods for the Insulation test.

CLI and IEC Insulation The test is performed between the EUT test socket live and neutral and the EUT test socket earth pin. For IEC leads the other end of the lead should be connected into the IEC test socket.

CLII Insulation The test is performed between the EUT test socket live and neutral and Red test terminal.

Point to Point Insulation The test is performed between the Red and Black test terminals, both the continuity test leads are required for this test.

Always ensure that you have selected the correct test connection method in the test for the probe connections made. Ensure that the appliance mains switch is in the ON position. During this test, 250V or 500V D.C. is applied between the two connections points. The 500V D.C. potential will be present across the two probe tips during a Point to Point test. Selecting test type In manual PAT test mode, the insulation test can be switched between a 250V EUT Insulation test, 500V EUT Insulation test, 250V Point to Point Insulation test or 500V Point to Point Insulation test as follows: Select Insulation Resistance (2) and press the setup key (F3). In the Test Type field, select the required test. During automatic sequences, the test type will be as per the test type programmed in the test sequence. In manual mode once the correct connections have been made for the selected test type press the Start button, in automatic mode the test will proceed automatically. The test will continue until it times out. If we wish to abort the current test press the Stop button. The measurement will be displayed in Mega Ohms. If an EUT fails the Insulation test then this may be because of internal filtering or an MOV. Retry the test at 250V or substitute the Insulation test with a Protective Conductor or Touch Current test.

Substitute Leakage This test is applicable to Class I and Class II equipment. This test is used to that the leakage between the mains conductors of the EUT to the EUT earth pin, or conductive accessible surface of the enclosure, is to a satisfactory low level. There are two possible connection methods for the Substitute Leakage test. CLI and IEC Substitute Leakage The test is performed between the EUT test socket live and neutral and the EUT socket earth pin. For IEC leads the other end of the lead should be connected into the IEC test socket.

CLII Substitute Leakage The test is performed between the EUT socket live and neutral and Red test terminal.

During this test, 40V A.C. is applied between the earth pin and both the live and neutral pins of the appliance mains supply plug. In manual mode once the correct connections have been made for the selected test type press the Start button, in automatic mode the test will proceed automatically. The test will continue until it times out. If we wish to abort the current test press the Stop button. The measurement will be displayed in milli Amps. This test can prove useful in situations where neither conventional insulation nor flash tests are acceptable methods of testing the insulation of the appliance. Please note that values for substitute leakage may differ substantially from that of conventional earth leakage tests because of the way that the test is performed (e.g. it will be affected by the presence of Neutral-to-Earth suppression capacitors).

Protective Earth (PE) Conductor Current Always test the earth continuity and insulation resistance before performing a PE Conductor Current test. Always check that an appliance with moving parts (e.g. an electric drill) is safely mounted to avoid risk of damage to equipment or personnel. Avoid prolonged, repeated use at full load (16A) and excessive test duration as this may reduce the life of the unit. Always ensure that appliance and leads, which include RCD protection, that the RCD is reset at the beginning of the test. Failure to do so may result in incorrect measurements being recorded.

This test is applicable on Class I Equipment. The Apollo 600 should be connected to a mains supply. The EUT should be connected into the EUT test socket. In manual mode once the correct connections have been made for the selected test type press the Start button, in automatic mode the test will proceed automatically.

The test will continue until it times out. If we wish to abort the current test press the Stop button. The measurement will be displayed in mA. Should the test measurement over range then the test will be aborted immediately and a fail will be logged.

Touch Current Warning: Always test the insulation resistance before performing a Touch Current test. Warning: Always check that an appliance with moving parts (e.g. an electric drill) is safely mounted to avoid risk of damage to equipment or personnel. Attention: Avoid prolonged, repeated use at full load (16A) and excessive test duration as this may reduce the life of the unit. Always ensure that appliance and leads, which include RCD protection, that the RCD is reset at the beginning of the test. Failure to do so may result in incorrect measurements being recorded. This test is applicable on Class I and Class II Equipment. The Apollo 600 should be connected to a mains supply. The EUT should be connected into the EUT socket, the red test terminal should be connected to point at which the leakage measurement is required.

In manual mode once the correct connections have been made for the selected test type press the Start button, in automatic mode the test will proceed automatically. The test will continue until it times out. If we wish to abort the current test press the Stop button. The measurement will be displayed in milli Amps. Should the test measurement over range then the test will be aborted immediately and a fail will be logged.

RCD Trip Time Voltages between the protective conductor and earth may influence measurements. This test will a sinusoidal current of 30mA between the EUT socket and the IEC socket, and measure the time it takes for the in-line RCD to trip. Remove all other connections before performing an RCD test.

The Apollo 600 should be connected to a mains supply. The RCD should be plugged into the EUT test socket and a connection should be made from the RCD mains output to the IEC test socket.

Once the correct connections have been made for the selected test type press the Start button. The RCD will be powered and you will be prompted to reset the RCD. When you have reset the RCD the Apollo 600 will count down and then perform the RCD test, the RCD trip time will be displayed. The measurement will be displayed in milli seconds.

IEC Lead / Polarity The IEC lead input is a test socket and is not intended to be connected directly to mains. Do not connect this input to the mains supply. The Polarity test checks the wiring polarity of an IEC lead, the IEC should be plugged into both the EUT and IEC test sockets.

This test can be used to test the wiring polarity of extension leads by plugging the supplied test IEC lead into the end of the extension lead to complete the circuit to the IEC tests socket. In the automatic sequence editor the Polarity can be added to sequence. In the manual mode the polarity test is already part of a pre-defined test sequence which includes an Earth Continuity test, an Insulation test and the Polarity test.

External Leakage Adaptors While using an External Leakage Adaptor the mains supply will be connected to the EUT through the adaptor. The External Leakage Adaptor test function is intended to used in conjunction with the one of Seaward's external leakage adaptors. Connect the external leakage adaptor into the Red test terminal, connect the Earth Continuity probe into the Black test terminal. Connect the mains supply and the EUT to the external leakage adaptor.

Note that connecting both the EUT and mains supply to the external leakage adaptor will connect the mains supply to the EUT.

11.4 Checkbox Verification The Apollo 600 comes supplied with a Checkbox. This can be used to that the Apollo 600 test functions are working correctly. When selecting the Checkbox function follow the onscreen instructions. The Checkbox function will perform a number of electrical tests. Ensure that the onscreen instructions are followed and that you do not touch the checkbox during the active tests.

11.5 PAT Settings This function allows you to configure the below factors with relation to PAT testing. Press this button to go to the next page.

Press this button to go to the previous page. Press this button to save changes and return to the previous screen.

Asset ID

This can be set to present a blank field, repeat the last Asset ID or automatically increment the Asset ID number for each successive test.

Start This field is used to set the starting point for the auto increment feature. The Increment value entered can be numeric or alpha-numeric ending with a numerical value. On Test Failure

In the event of a test failure during an automatic sequence, the Apollo 600 can be configured to either End Test, which will terminate the test sequence or present a Fail Menu, which will provide the following list of options: • • • • •

restart the test skip the test restart the test sequence (from the first test) abort the test sequence (without saving any results end the test sequence (and record a fail result)

Note: Restart Test is useful for coping with situations such as forgetting to connect the earth continuity probe. End Test Sequence will record a Fail result whereas Abort Test Sequence does not record a result. After Test There is a choice of 3 actions to be carried out at the end of a test sequence. New Test will auto save at the end of a test sequence and then open the Asset Details window ready for a new test. Print Label will auto save at the end of a test sequence and then open the Print Label window. When printing is complete, the tester will proceed to the next test and open the Asset Details window. Options Menu will auto save at the end of a test sequence and then open the Test Details window. Pressing (F4) will proceed to the Test Result Options window with a list of options including View Results, View Test Sequence, Information, Print Test Results or Print Label. Pressing Escape (F5) will return to the Asset Detail window ready to start the next appliance. Earth Result

This field can set to “Last” where the last reading taken during the measurement period is compared with the /fail limit or “Worst” where the highest reading taken during the measurement period is compared wit the /fail limit. Setting the field to “Worst” will cause the earth continuity test to fail if the reading exceeds the limit value at any point during the measurement period, for example if there is a momentary break in the protective conductor when the mains cable is flexed.

Earth reverse

This field is used to enable or disable automatic reversal of the earth continuity test current polarity. OFF sets the earth continuity test current to +200mA and ON sets the earth continuity test current to +200mA followed by -200mA.

Sub Lkg Factor

This field is used to set the substitute leakage scale factor to 0%, 6% or 10%. The Substitute Leakage reading is then calculated for 230V (0%), 244V (6%) or 253V (10%).

Comments Can be set to open the comment window: always (after every test sequence), if the test result is a , if the test result is a fail or never. New This field can be set to Clear where previous comments are removed from the Comments comments fields or Same as Last where the previous remain in the comments fields. This can be useful when performing repeated tests on the same type of appliance. Comments This allows the field descriptor for each of the four comment lines to be changed Line to show Notes, Asset Description, Asset Group, Make, Model or Serial Number or Location as required. CheckBox This field is used to set the frequency of the CheckBox reminder to none, daily, Interval weekly or monthly.

12. Universal Risk Assessment This menu allows you to complete risk assessments for any workplace hazard and calculate a risk score. This is the Settings function. This function allows you to configure settings such as how the Hazard ID should be filled. Add new Hazard. This will take you to fill in the Hazard ID, if necessary. Select a Site and Location from the dropdown using the arrow keys or enter a new one if necessary. Press the ‘Accept’ button to fill in the form. Use the arrow keys to move through the form and the QWERTY keyboard to fill in the relevant fields. Use the right and Left Arrow keys to select ‘Impact of Risk event’ and ‘Probability of Occurrence’. This will give a calculated score between 1-12 for ‘Priority of Risk Level’ and ‘Advice’ based on this score. If necessary you can ‘Add’ corrective actions, assign them to personnel and give dates for completion. You can use the Camera function to attach photos to the record.

This button will enable and disable the flash light. Press this button to take the picture.

This button will attach the picture and go back to the record. To add another picture press the ‘Camera’ button again. This button will cancel the picture and allow you to take another.

Press this button to save changes and return to the previous screen.

13. Health & Safety Reports This menu allows you to complete and save Health & Safety forms such as Emergency Lighting and Fire Alarm & System Inspection reports. To fill in a new form Fill in the form ID number and select a Site and Location from the dropdown using the arrow keys or enter a new one if necessary. Select which form you wish to complete from the dropdown using the arrow keys. Press the ‘Accept’ button to open the form. Use the arrow keys to move through the form and the QWERTY keyboard to fill in the relevant fields. You can use the Camera function to attach photos to the record.

This button will enable and disable the flash light. Press this button to take the picture. This button will attach the picture and go back to the record. To add another picture press the ‘Camera’ button again. This button will cancel the picture and allow you to take another. Press this button to save changes and return to the previous screen.

14. Updating your Firmware 1.

Go to www.seaward.co.uk/firmware and save the latest Apollo 600 firmware file to a USB memory stick.

2.

Power on the unit whilst holding down the F1 button.

3.

Press F2 to update via memory stick.

4.

Follow the onscreen instructions.

5.

Restart the unit. You can check the firmware version of your tester by pressing this icon in the Home screen.

15. Electrical Specification Earth Continuity Output Current (Load 2Ω): Test Voltage (o/c) : Measuring Range: Display Range: Resolution: Operating Error: Number of tests as per IEC615574:

+/- 200mA DC with ZAP > 4VDC 0.05Ω – 19.99Ω 0.01Ω – 19.99Ω 0.01Ω +/-5% + 2 counts approx 1,500.

Insulation Test Test Voltages: Test Current:

500V and 250V DC 1mA minimum for a load of 1kohm/volt, <2mA into s/c Test Voltage Accuracy: +20%, -0% Measuring Range: 0.10MΩ to 19.99MΩ Display Range: 0.00MΩ to 19.99MΩ Resolution: 0.01MΩ Operating Error: +/-5% +5 counts (0.10MΩ to 9.99MΩ) +/-10% +5 counts (10.00MΩ to 19.99MΩ) Number of tests as per IEC61557- approx 1,500. 2:

Subsitute Leakage Test Test Voltages: Measuring Range: Display Range: Resolution: Operating Error:

>25Vac <50Vac 0.20mA to 19.99mA 0.00mA to 19.99mA 0.01mA +/-10% +2 digits

Protective Conductor Current Test Voltage: Display Range: Measurement Range: Resolution: Operating Error: Frequency Response:

Supply Voltage, maximum load current 16A 0.01mA to 19.99mA 0.25mA to 19.99mA 0.01mA +/-5% of reading +/- 3 digits 40Hz to 2.5 kHz

Touch Current Test Voltage: Display Range: Measurement Range: Resolution: Operating Error: Frequency Response:

Supply Voltage, maximum load current 16A 0.00mA to 3.50mA 0.10mA to 3.50mA 0.01mA +/-5% of reading +/- 2 digits DC to 2.5 kHz

Load Power/Current Test Voltage: Display Range: Measurement Range: Resolution: Operating Error:

Supply Voltage, maximum load current 16A 0.00 - 16.00A 0.50 - 16.00A 0.01A +/-10% of reading +/- 5 digits

Lead Test Test Voltage: Test:

5V DC nominal Live / Neutral checks for o/c, s/c and crossed

Power Socket Test Input voltage range:

195V – 253V AC Indicates configuration of voltage potential:Line potential phase to earth Line potential phase to neutral Line potential neutral to earth

RCD Test Test Voltage: Test Current: Test Current Accuracy: Display Range: Measuring Range: Resolution: Operating Error:

230V +10%, -15% 15mA / 30mA rms sinusoidal 15mA -10% +0%, 30mA +10, 0% 0 – 2000ms 1ms – 2000ms 1ms ±1ms

External Leakage Test Voltage: Display Range: Measuring Range: Resolution: Operating Error:

Connected to External Adapter 0mA - 9.99mA 0.25mA - 9.99mA 0.01mA +-5%of reading +-2 digits

16. Useful Information 16.1 Factory Set Test Sequences

Visual

Earth Continuity

PE Conductor Current

Insulation

Touch Current

Substitute Leakage

Wiring

RCD Trip Time

Test

Name Portable/Handheld/IT CLI Portable/Handheld/IT CLII Fixed Appliance CLI Fixed Appliance CLII IEC Lead 2m 13A 5m Surge Protected Lead 13A 25m Ext Lead 30mA RCD Portable CLI PE Current Portable CLII Touch Current IT Equip CLI PE Current IT Equip CLII T ouch Current 13A 6m Mains Lead 13A 12m Mains Lead 13A 24m Mains Lead Mov/Stat CLI 500V Insulation

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Duration (s)

Limit (Ω)

Duration (s)

Voltage

Limit (MΩ)

5

0.1

2

0.1

5 5 5 5

0.2 0.2 0.5 0.5

2 2 5 5 2 2

500 500 500 500 500 250

1 2 1 2 1 1

5 5 5 5 5

0.1 0.2 0.3 0.5 0.1

2 2 2 2 2 2 2 2

250 250 250 250 500 500 500 500

1 2 1 1 1 1 1

Duration (s)

Limit (mA)

Duration (s)

Limit (mA)

Duration (s)

Limit (mA)

Limit (ms)

Yes Yes 5 5 5

0.8 0.8

30 5

0.3

5

0.3

3.5 Yes Yes Yes

Visual

Earth Continuity

PE Conductor Current

Insulation

Touch Current

Substitute Leakage

Wiring

RCD Trip Time

Test

Name Mov/Stat CLII 500V Insulation Mov/Stat CLI PE Current Mov/Stat CLII Touch Current 110V Handheld/Portable CLI 110V Handheld/Portable CLII 110V Movable/Stationary CLI 110V Movable/Stationary CLII 110V 25m Lead Rpe&Insulation Visual Only

Yes Yes Yes Yes Yes Yes Yes Yes Yes

Duration (s)

Limit (Ω)

5

0.1

5

0.1

5

0.1

5

0.5

Duration (s)

Voltage

Limit (MΩ)

2 2 2 2 2 2 2

500 250 250 500 500 500 500

2 1 2 1 2 1 2

2

500

1

Duration (s)

Limit (mA)

5

3.5

Duration (s)

Limit (mA)

5

3.5

Duration (s)

Limit (mA)

2 2 2 2

0.8 0.3 3.5 0.3

Limit (ms)

16.2 Other Information Parameter Earth Continuity P/F limit (Ω) Earth Continuity Duration (s) Insulation Resistance P/F limit (MΩ) Insulation Resistance Duration (s) Substitute Leakage P/F limit (mA) Substitute Leakage Duration (s) IEC Cord Earth Continuity P/F limit (ohms) IEC Cord Insulation P/F limit (MΩ) Touch Current P/F limit (mA) Touch Current Duration (s) PE Conductor Current P/F limit (mA) PE Conductor Current Duration (s) External Adapter Continuity (Ω) External Adapter Leakage (mA) External Adapter Duration (s) RCD 30mA trip time (ms) RCD 150mA trip time (ms) Number of tests in a test sequence Characters in a test sequence name Characters in a Test name Characters in a Test Unit Total number of Test Sequences Test Results Memory (Mbytes) Test Results (typical) Sites Characters in Site name Locations Characters in Location name s Characters in name Comments List Characters in Comment Characters in Asset ID

Default 0.1 5 1 5 0.75 5

Min 0.01 2 0.01 2 0.25 2

Max 19.99 30 19.99 30 15 30

0.1 1 0.25 5 0.75 5 0.1 0.75 5 200 40

0.01 0.01 0.25 2 0.25 2 0.01 0.25 2 1 1 1 1 1

5 19.99 3.50 30 19.99 30 5 9.99 30 2000 40 60 30 15 15 100 300 50000 100 15 100 15 50 15 100 25 15

1 1 1

1

17. Environmental Conditions The Apollo 600 has been designed to perform tests and measurements in a dry environment. Maximum barometric elevation for making measurements is 2000M. Pollution degree 2 according to IEC 60529. Electromagnetic compatibility (EMC). Interference immunity and emitted interference conforming to IEC 61326-1. Operating temperature range of 0 to 40 degrees C, without moisture condensation. Operating Altitude 0 to 2000 metres.

18. Maintenance 18.1 Charging the battery pack. The battery pack will be charged whenever the Apollo 600 is connected to the mains supply regardless of whether it is switched on or off. The typical charging current is set to 500mA but this may vary as the instrument also includes pre-charge and top up charge modes. When no tests are being performed the battery pack will be fully re-charged after 7 hours.

18.2 Securing the Apollo 600 Under certain conditions safe operation of the Apollo 600 can no longer be assumed: Visible damage of the instrument case. Incorrect measurement results. Recognisable abuse to the instrument due to prolonged storage under improper conditions. Recognisable abuse to the instrument due to extraordinary transportation stress. In these case the Apollo 600 should be immediately switched off, disconnected from any test and measurement function and secured to prevent any further use.

18.3 Cleaning the Apollo 600 Clean the external case of the Apollo 600 with a dry clean cloth. Avoid using solvents and abrasive scouring agents to clean the external case of the Apollo 600.

18.4 Replacing the battery pack. Before opening the Apollo 600 battery compartment ensure that all test leads and accessories are disconnected.

Power off the instrument. Disconnect all test leads and accessories. Position the instrument face down and remove the screw holding the battery compartment cover in place. Remove the battery compartment cover. Remove the battery pack from the compartment and unplug the 4 way connector. Connect the 4 way connector of the new battery to the 4 way header in the battery compartment, put the battery pack into the compartment. Relocate the battery compartment cover and fasten in position with the battery compartment screw. ONLY USE A REPLACEMENT BATTERY PACK THAT HAS BEEN SUPPLIED BY SEAWARD OR A SEAWARD APPROVED DISTRIBUTOR.

19. The Apollo 600 must be ed with Seaward before will be made available. For Technical : Tel: (+44) 191 587 8718 For help or advice on Service and Calibration : CalibrationHouse Seaward Electronic Bracken Hill South West Industrial Estate Peterlee Co Durham SR8 2SW England Tel: (+44) 191 5878739 (+44) 191 5878737 Email: [email protected] Calibration House is part of the Seaward Group.

19.1 your product here:-

www.seaward.co.uk

19.2 Calibration Services:-

www.calibrationhouse.co.uk Bracken Hill South West Industrial Estate Peterlee County Durham SR8 2SW Co Durham SR8 2SW England Tel: (+44) 191 5863511 Part Number 380A558 Revision A October 2012

© 2013 Seaward Electronic Ltd Some icons provided by Fat Cow (http://www.fatcow.com/free-icons/) Based in part on the work of the Qwt project (http://qwt.sf.net)