Msds Penguard Midcoat B Jotun 64t4b

Conforms to WHIMS 2015, Canadian Hazardous Products Regulation (HPR)

SAFETY DATA SHEET Penguard Midcoat Comp A Section 1. Identification Product identifier

: Penguard Midcoat Comp A

Product code

: 2080

Product description

: Paint.

Other means of identification

: Not available.

Product type

: Liquid.

Supplier's details

: Jotun Paints, Inc. 9203 Highway 23 Belle Chasse, LA 70037 Telephone: (800) 229-3538 or +1 504-394-3538 [email protected]

Emergency telephone number (with hours of operation)

: 1-800-424-9300 (Staffed 24/7)

2080;2081

1

2080

epoxy

^(ValidationDate)

1

Approved

Section 2. Hazard identification Classification of the substance or mixture

: FLAMMABLE LIQUIDS - Category 3 SKIN IRRITATION - Category 2 SERIOUS EYE DAMAGE - Category 1 SKIN SENSITIZATION - Category 1 SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) - Category 2 AQUATIC HAZARD (LONG-TERM) - Category 3

GHS label elements Hazard pictograms

:

Signal word

: Danger.

Hazard statements

: Flammable liquid and vapor. Causes serious eye damage. Causes skin irritation. May cause an allergic skin reaction. May cause damage to organs through prolonged or repeated exposure. (hearing organs) Harmful to aquatic life with long lasting effects.

Precautionary statements Prevention

Date of issue

: Wear protective gloves. Wear eye or face protection. Wear protective clothing. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid release to the environment. Do not breathe vapor or spray. Wash hands thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace.

:

08.11.2017

1/12

Penguard Midcoat Comp A

Section 2. Hazard identification Response

Storage Disposal

: Get medical attention if you feel unwell. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing and wash it before reuse. If skin irritation or rash occurs: Get medical attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or physician. : Not applicable. : Dispose of contents and container in accordance with all local, regional, national and international regulations.

Section 3. Composition/information on ingredients Substance/mixture

: Mixture

Other means of identification

: Not available.

CAS number/other identifiers CAS number

: Not applicable.

Product code

: 2080

Ingredient name

%

CAS number

epoxy resin (MW ≤ 700) 2-methylpropan-1-ol ethylbenzene bisamide mixture

≥10 - <25 ≤5 ≤3 <1

25068-38-6 78-83-1 100-41-4 911674-82-3

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. Occupational exposure limits, if available, are listed in Section 8.

Section 4. First-aid measures Description of necessary first aid measures Eye

Inhalation

Skin

Date of issue

: Get medical attention immediately. Call a poison center or physician. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any lenses. Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly by a physician. : Get medical attention immediately. Call a poison center or physician. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. : Get medical attention immediately. Call a poison center or physician. Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly by a physician. In the event of any complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean shoes thoroughly before reuse.

:

08.11.2017

2/12

Penguard Midcoat Comp A

Section 4. First-aid measures Ingestion

: Get medical attention immediately. Call a poison center or physician. Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Chemical burns must be treated promptly by a physician. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed Potential acute health effects Eye

: Causes serious eye damage.

Inhalation

: No known significant effects or critical hazards.

Skin

: Causes skin irritation. May cause an allergic skin reaction.

Ingestion

: No known significant effects or critical hazards.

Over-exposure signs/symptoms Eye

Inhalation Skin

Ingestion

: Adverse symptoms may include the following: pain watering redness : No specific data. : Adverse symptoms may include the following: pain or irritation redness blistering may occur : Adverse symptoms may include the following: stomach pains

Indication of immediate medical attention and special treatment needed, if necessary Notes to physician Specific treatments Protection of first-aiders

: Treat symptomatically. poison treatment specialist immediately if large quantities have been ingested or inhaled. : No specific treatment. : No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.

See toxicological information (Section 11)

Section 5. Fire-fighting measures Extinguishing media Suitable extinguishing media

: Use dry chemical, CO₂, water spray (fog) or foam.

Unsuitable extinguishing media

: Do not use water jet.

Specific hazards arising from the chemical

Date of issue

: Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Runoff to sewer may create fire or explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain. :

08.11.2017

3/12

Penguard Midcoat Comp A

Section 5. Fire-fighting measures Hazardous thermal decomposition products

Special protective actions for fire-fighters

Special protective equipment for fire-fighters

: Decomposition products may include the following materials: carbon dioxide carbon monoxide halogenated compounds metal oxide/oxides : Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. : Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures Personal precautions, protective equipment and emergency procedures For non-emergency personnel

: No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Do not breathe vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non-emergency personnel". Environmental precautions

: Avoid dispersal of spilled material and runoff and with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities.

Methods and materials for containment and cleaning up Small spill

Large spill

: Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with noncombustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency information and Section 13 for waste disposal.

Section 7. Handling and storage Precautions for safe handling Protective measures

Date of issue

: Put on appropriate personal protective equipment (see Section 8). Persons with a history of skin sensitization problems should not be employed in any process in which this product is used. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not ingest. Avoid release to the environment. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take :

08.11.2017

4/12

Penguard Midcoat Comp A

Section 7. Handling and storage precautionary measures against electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container. Advice on general occupational hygiene

Conditions for safe storage, including any incompatibilities

: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. : Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and wellventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination.

Section 8. Exposure controls/personal protection Control parameters Occupational exposure limits Ingredient name

Exposure limits

2-methylpropan-1-ol

CA Alberta Provincial (Canada, 4/2009). Skin sensitizer. 8 hrs OEL: 152 mg/m³ 8 hours. 8 hrs OEL: 50 ppm 8 hours. CA British Columbia Provincial (Canada, 5/2015). TWA: 50 ppm 8 hours. CA Ontario Provincial (Canada, 7/2015). TWA: 50 ppm 8 hours. CA Quebec Provincial (Canada, 1/2014). TWAEV: 152 mg/m³ 8 hours. TWAEV: 50 ppm 8 hours. CA Alberta Provincial (Canada, 4/2009). 8 hrs OEL: 100 ppm 8 hours. 8 hrs OEL: 434 mg/m³ 8 hours. 15 min OEL: 543 mg/m³ 15 minutes. 15 min OEL: 125 ppm 15 minutes. CA British Columbia Provincial (Canada, 5/2015). TWA: 20 ppm 8 hours. CA Ontario Provincial (Canada, 7/2015). TWA: 20 ppm 8 hours. CA Quebec Provincial (Canada, 1/2014). TWAEV: 100 ppm 8 hours. TWAEV: 434 mg/m³ 8 hours. STEV: 125 ppm 15 minutes. STEV: 543 mg/m³ 15 minutes.

ethylbenzene

Appropriate engineering controls

Environmental exposure controls

Date of issue

: Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. :

08.11.2017

5/12

Penguard Midcoat Comp A

Section 8. Exposure controls/personal protection Individual protection measures Hygiene measures

Eye/face protection

: Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. : Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles and/or face shield. If inhalation hazards exist, a full-face respirator may be required instead.

Skin protection Hand protection

: Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. There is no one glove material or combination of materials that will give unlimited resistance to any individual or combination of chemicals. The breakthrough time must be greater than the end use time of the product. The instructions and information provided by the glove manufacturer on use, storage, maintenance and replacement must be followed. Gloves should be replaced regularly and if there is any sign of damage to the glove material. Always ensure that gloves are free from defects and that they are stored and used correctly. The performance or effectiveness of the glove may be reduced by physical/chemical damage and poor maintenance. Barrier creams may help to protect the exposed areas of the skin but should not be applied once exposure has occurred. Wear suitable gloves tested to EN374. Recommended, gloves(breakthrough time) > 8 hours: Viton®, Responder, 4H, Teflon Not recommended, gloves(breakthrough time) < 1 hour: PVC May be used, gloves(breakthrough time) 4 - 8 hours: nitrile rubber, neoprene, butyl rubber, polyvinyl alcohol (PVA)

Body protection

: Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. When there is a risk of ignition from static electricity, wear anti-static protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves. : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. : Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Other skin protection

Respiratory protection

Date of issue

:

08.11.2017

6/12

Penguard Midcoat Comp A

Section 9. Physical and chemical properties Appearance Physical state

: Liquid.

Color

: Various colors.

Odor Odor threshold pH Melting point Boiling point

: Characteristic. : Not available. : Not available. : Not available.

Flash point

: Lowest known value: 108°C (226.4°F) (2-methylpropan-1-ol). Weighted average: 223.78°C (434.8°F) : Closed cup: 25°C (77°F)

Evaporation rate

: Not available.

Flammability (solid, gas)

: Not available.

Lower and upper explosive (flammable) limits

: Not available.

Vapor pressure

: Not available.

Vapor density Relative density

: Not available. : 1.815 to 1.892 g/cm³

Solubility

: Insoluble in the following materials: cold water and hot water.

Partition coefficient: noctanol/water

: Not available.

Auto-ignition temperature

: Not available.

Decomposition temperature

: Not available.

Viscosity

: Kinematic (40°C (104°F)): >0.205 cm2/s (>20.5 mm2/s)

15.15 to 15.79 pounds/gallon

Section 10. Stability and reactivity Reactivity

: No specific test data related to reactivity available for this product or its ingredients.

Chemical stability

: The product is stable.

Possibility of hazardous reactions

: Under normal conditions of storage and use, hazardous reactions will not occur.

Conditions to avoid

: Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition.

Incompatible materials

: Reactive or incompatible with the following materials: oxidizing materials

Hazardous decomposition products

: Under normal conditions of storage and use, hazardous decomposition products should not be produced.

Section 11. Toxicological information Information on toxicological effects Acute toxicity Product/ingredient name

Result

Species

Dose

Exposure

2-methylpropan-1-ol

LC50 Inhalation Vapor LD50 Dermal LD50 Oral LC50 Inhalation Gas. LD50 Dermal LD50 Oral

Rat Rabbit Rat Rabbit Rabbit Rat

19200 mg/m³ 3400 mg/kg 2460 mg/kg 4000 ppm >5000 mg/kg 3500 mg/kg

4 hours 4 hours -

ethylbenzene

Date of issue

:

08.11.2017

7/12

Penguard Midcoat Comp A

Section 11. Toxicological information Irritation/Corrosion Not available. Sensitization Not available. Mutagenicity Not available. Carcinogenicity Not available. Reproductive toxicity Not available. Teratogenicity Not available. Specific target organ toxicity (single exposure) Name

Category

Route of exposure

Target organs

2-methylpropan-1-ol

Category 3

Not applicable.

Respiratory tract irritation and Narcotic effects

Name

Category

Route of exposure

Target organs

ethylbenzene

Category 2

Not determined

hearing organs

Specific target organ toxicity (repeated exposure)

Aspiration hazard Name

Result

ethylbenzene

ASPIRATION HAZARD - Category 1

Information on the likely routes of exposure

: Not available.

Potential acute health effects Eye

: Causes serious eye damage.

Inhalation

: No known significant effects or critical hazards.

Skin

: Causes skin irritation. May cause an allergic skin reaction.

Ingestion

: No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics Eye

Inhalation Skin

Ingestion

: Adverse symptoms may include the following: pain watering redness : No specific data. : Adverse symptoms may include the following: pain or irritation redness blistering may occur : Adverse symptoms may include the following: stomach pains

Delayed and immediate effects and also chronic effects from short and long term exposure Date of issue

:

08.11.2017

8/12

Penguard Midcoat Comp A

Section 11. Toxicological information Short term exposure Potential immediate effects

: Not available.

Potential delayed effects

: Not available.

Long term exposure Potential immediate effects

: Not available.

Potential delayed effects

: Not available.

Potential chronic health effects Not available. General

Carcinogenicity

: May cause damage to organs through prolonged or repeated exposure. Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels. : No known significant effects or critical hazards.

Mutagenicity

: No known significant effects or critical hazards.

Teratogenicity

: No known significant effects or critical hazards.

Developmental effects

: No known significant effects or critical hazards.

Fertility effects

: No known significant effects or critical hazards.

Numerical measures of toxicity Acute toxicity estimates Route

ATE value

Oral Dermal Inhalation (vapors)

21147.1 mg/kg 17848.7 mg/kg 125 mg/l

Section 12. Ecological information Toxicity Product/ingredient name

Result

Species

Exposure

epoxy resin (MW ≤ 700)

Acute EC50 1.4 mg/l Acute LC50 3.1 mg/l Chronic NOEC 0.3 mg/l Chronic NOEC 4000 µg/l Fresh water Acute EC50 7.2 mg/l Acute EC50 2.93 mg/l Acute LC50 4.2 mg/l

Daphnia Fish - fathead minnow Fish Daphnia - Daphnia magna Algae Daphnia Fish

48 hours 96 hours 21 days 21 days 48 hours 48 hours 96 hours

2-methylpropan-1-ol ethylbenzene

Persistence and degradability Product/ingredient name

Aquatic half-life

Photolysis

Biodegradability

epoxy resin (MW ≤ 700) ethylbenzene

-

-

Not readily Readily

Bioaccumulative potential Product/ingredient name

LogPow

BCF

Potential

epoxy resin (MW ≤ 700) 2-methylpropan-1-ol ethylbenzene

2.64 to 3.78 1 3.6

31 -

low low low

Date of issue

:

08.11.2017

9/12

Penguard Midcoat Comp A

Section 12. Ecological information Mobility in soil Soil/water partition coefficient (KOC)

: Not available.

Other adverse effects

: No known significant effects or critical hazards.

Section 13. Disposal considerations Disposal methods

: The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and nonrecyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Vapor from product residues may create a highly flammable or explosive atmosphere inside the container. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and with soil, waterways, drains and sewers. Do not allow to enter drains or watercourses. Material and/or container must be disposed of as hazardous waste.

Section 14. Transport information TDG Classification

DOT Classification

ADR/RID

IMDG

IATA

UN number

1263

1263

1263

1263

1263

UN proper shipping name

Paint.

Paint.

Paint.

Paint.

Paint.

Transport 3 hazard class(es)

3

3

3

3

Packing group

III

III

III

III

III

Environmental hazards

No.

No.

No.

No.

No.

Additional information TDG Classification DOT Classification

ADR/RID

IMDG

Date of issue

: Product classified as per the following sections of the Transportation of Dangerous Goods Regulations: 2.18-2.19 (Class 3). : Reportable quantity 1979.7 lbs / 898.8 kg [128.1 gal / 484.92 L] Package sizes shipped in quantities less than the product reportable quantity are not subject to the RQ (reportable quantity) transportation requirements. : Tunnel restriction code: (D/E) Hazard identification number: 30 ADR/RID: Viscous substance. Not restricted, ref. chapter 2.2.3.1.5 (applicable to receptacles < 450 litre capacity). : Emergency schedules (EmS): F-E, S-E Marine pollutant: No.

:

08.11.2017

10/12

Penguard Midcoat Comp A

Section 14. Transport information IATA

IMDG: Viscous substance. Transport in accordance with paragraph 2.3.2.5 (applicable to receptacles < 30 litre capacity). : -

Special precautions for : Transport within ’s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. Transport in bulk according to Annex II of MARPOL and the IBC Code

: Not available.

Section 15. Regulatory information Canadian lists Canadian NPRI CEPA Toxic substances Canada inventory

: The following components are listed: i-Butyl alcohol; Xylene (all isomers); Ethylbenzene : None of the components are listed. : Not determined.

International regulations Chemical Weapon Convention List Schedules I, II & III Chemicals Not listed. Montreal Protocol (Annexes A, B, C, E) Not listed. Stockholm Convention on Persistent Organic Pollutants Not listed. Rotterdam Convention on Prior Inform Consent (PIC) Not listed. UNECE Aarhus Protocol on POPs and Heavy Metals Not listed. Inventory list Australia

: Not determined.

China

: Not determined.

Europe

: At least one component is not listed.

Japan

: Japan inventory (ENCS): Not determined. Japan inventory (ISHL): Not determined.

Malaysia

: Not determined.

New Zealand

: Not determined.

Philippines

: Not determined.

Republic of Korea

: Not determined.

Taiwan

: Not determined.

Turkey

: Not determined.

United States

: Not determined.

Date of issue

:

08.11.2017

11/12

Penguard Midcoat Comp A

Section 16. Other information History Date of printing

: 08.11.2017

Date of issue/Date of revision Date of previous issue

: 08.11.2017

Version

: 1

: No previous validation

Key to abbreviations

: ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations HPR = Hazardous Products Regulations Procedure used to derive the classification Classification FLAMMABLE LIQUIDS - Category 3 SKIN IRRITATION - Category 2 SERIOUS EYE DAMAGE - Category 1 SKIN SENSITIZATION - Category 1 SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) - Category 2 AQUATIC HAZARD (LONG-TERM) - Category 3 References

Justification On basis of test data Calculation method Calculation method Calculation method Calculation method Calculation method

: Not available.

Indicates information that has changed from previously issued version. Notice to reader The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical experience. Jotun's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further notice. s should always consult Jotun for specific guidance on the general suitability of this product for their needs and specific application practices. If there is any inconsistency between different language issues of this document, the English (United Kingdom) version will prevail.

Date of issue

:

08.11.2017

12/12