Merlin M1x Keypad Manual 121d1a

GROUP OF COMPANIES

MERLIN M-SERIES -

Electric Fence Control

MANUAL

FENCE

GATE

SERVICE

SINGLE ZONE M18

M15

M14 1

MERLIN Electric Fence Control

Manual

SWITCH THE FENCE ON / OFF #

To switch the fence On or Off, enter your four digit PIN followed by the # key. The control will beep twice to confirm that the fence is off and three times when the fence is turned on. x

If the red ON light is lit or flashing, the fence is energized

x

Don’t pause for more than 5 seconds while entering the digits, or the control will reject your PIN number

x

If you make a mistake while entering your PIN, press the # key and start again

x

An incorrect PIN will cause the control to beep 5 times

x

The default master PIN is 1 2 3 4

AFTER AN ALARM OCCURS #

Enter your PIN and push the # key. This will silence the buzzer and siren. It will not switch the fence off. One of the ALARM lights will flash or stay lit to indicate the type of alarm. Investigate the cause of the alarm and correct it. After the ALARM light stops flashing, enter your PIN and push the # key to clear the alarm memory.

CHANGE THE VOLTAGE ON THE FENCE 3

#

Enter your PIN and push the * key, enter the digit ‘3’, then push# key. The control will beep three times to confirm the fence is in low voltage mode. When the fence is on and in low voltage mode, the red ON light will flash. The red ON light will stay lit if the fence is in high voltage mode.

BY THE FENCE ALARM 1

#

Enter your PIN and push the * key, enter the digit ‘1’, then push the # key. The control will beep 3 times and the FENCE ALARM light will start flashing slowly to confirm the fence alarm is byed. To cancel the by, repeat the same sequence of keys.

BY THE SIREN AND STROBE LIGHT (SILENT ALARM) 4

#

Enter your PIN and push the * key, enter the digit ‘4’, then push the # key. The control will beep 3 times to confirm the siren and strobe light is byed. The beeper in the control and the energizer unit will still be active.

UN-BY THE SIREN AND STROBE LIGHT 7

#

Enter you PIN and push the * key, enter the digit ‘7’, then push the # key. The control will beep twice to confirm that the siren and strobe light is NOT byed.

2

MERLIN Electric Fence Control

Manual

MAKE THE GATE ALARM IMMEDIATE 2

7

#

Enter you PIN and push the * key, enter the digit ‘2’ followed by the digit ‘7’, then push the # key. The control will beep twice and the GATE ALARM light will start flashing very slowly (every 5 seconds) to confirm that the gate alarm is immediate.

MAKE THE GATE ALARM DELAYED 2

4

#

Enter you PIN and push the * key, enter the digit ‘2’ followed by the digit ‘4’, then push the # key. The control will beep twice to confirm that the gate alarm is delayed. The default delay time is 4 minutes.

BY THE GATE ALARM 2

#

Enter you PIN and push the * key, enter the digit ‘2’, then push the # key. The control will beep 3 times and the GATE ALARM light will start flashing slowly to confirm the gate alarm is byed. To cancel the by, repeat the same sequence of keys.

TURN THE GATE CHIME ON / OFF 2

#

Push the * key, enter the digit ‘2’, then push the # key. The control will beep twice to confirm that the gate chime is turned off and three times if it’s turned on. If the chime is on, the control will beep twice if the gate closes and three times if it opens.

BY THE SERVICE ALARM 9

#

Enter you PIN and push the * key, enter the digit ‘9’, then push the # key. The control will beep 3 times and the SERVICE ALARM light will start flashing slowly to confirm that the service alarm is byed. To cancel the by, repeat the same sequence of keys.

STANDBY BATTERY TEST 6

#

Push the * key, enter the digit ‘6’, then push the # key. The control will beep twice and start testing the battery. The default battery test duration is 5 minutes.

CHANGING A PIN 0

# # # #

Master PIN (1-6) New PIN New PIN

Enter your master PIN, push the * key, enter the digit ‘0’, then push the # key. Enter the number (1-6), and push the # key. number 1 is the master PIN. Enter that ’s new PIN and push the # key. Enter the new PIN again and push the # key. If the new PIN is accepted, the control will beep twice. If you make a mistake while programming, or if the system rejects the new PIN, the control will beep five times. The default master PIN is 1 2 3 4.

3

MERLIN Electric Fence Control

Manual

KEY DEFINITIONS: Four digit Personal Identification Number (PIN) WHAT THE LIGHTS MEAN: Power Light

On Light

Gate Light

Service Light

Good Light

Fence Light

FENCE GOOD

ON

ON

OFF

OFF

SLOW FLASH

OFF

FENCE OFF

ON

OFF

OFF

OFF

OFF

OFF

MAINS FAILURE

OFF

Condition:

BATTERY LOW BATTERY FLAT

SLOW FLASH SLOW FLASH

FENCE CHECK FENCE CHECK

SLOW FLASH SLOW FLASH

FAST FLASH

ON

OFF

OFF

OFF

OFF

OFF

FAST FLASH

SLOW FLASH SLOW FLASH

FENCE BY GATE OPEN GATE BY INSTANT GATE

FAST FLASH SLOW FLASH PULSE (5 SEC)

SERVICE ALARM SERVICE BY ALARM MEMORY

Fence on, working properly Fence off, working properly System on battery power Check mains supply

FENCE ALARM FENCE LV MODE

Remarks

(ON)

Check mains, call for service Check fence for vegetation Check fence for vegetation Problem on fence Fence in low voltage mode Fence alarm switched off Gate is open Gate alarm is switched off Instant gate alarm

FAST FLASH SLOW FLASH (ON)

Call for service

(ON)

Service alarm is switched off Old alarm condition

NEMTEK GROUP OUTLETS RANDBURG

EDENVALE

Tel: +27 (0)11 462-8283 Fax: +27 (0)11 462-7132

Tel: +27 (0)11 453-1970 Fax: +27 (0)11 453-1858 Web site: http//www.nemtek.com E-mail: [email protected] MANUFACTURED IN SOUTH AFRICA

4