Flow Meter 6d64m

FT Series Turbine Flowmeters Description Flow Technology’s FT Series turbine flowmeters utilize a proven flow measurement technology to provide exceptionally reliable digital outputs. Because of their versatility, these flowmeters are the solution for a wide variety of liquid and gas flow sensing applications. FT Series turbine flowmeters, which range in size from 3/8 inch to 24 inches, offer a high turn-down capability, repeatability of ±0.05% (liquid) and ±0.1% (gas) of reading, and excellent speed of response. The precision, axial-mounted rotor design of the standard turbine flowmeter allows it to operate effectively in flow rates from 0.03 to 50,000 GPM to (0.11 to 189,000 LPM) in liquid and 0.09 to 15,000 ACFM (2.55 to 424,800 ALPM) in gas, and pressures as high as 4,000 BAR (58,000 psi) for certain applications. Linearity is rated at ±0.5% of reading over the normal 10:1 turn-down range for liquid ( linearity of ±0.25% offered) and ±1.0% of full scale over the normal range for gas. All turbine flowmeters can achieve ±0.1% linearity with linearizing electronics. A choice of construction materials can be specified for the turbine flowmeter’s housing, rotor, bearings and shaft, including standard stainless steel, and exotic materials for specialized applications.

Applications Flow Technology offers a wide range of turbine flowmeters and custom-engineered designs for liquid and gas applications to meet the demands of the Aerospace, Industrial and Automotive s. Examples of applications include fuel consumption, hydraulics, coolant, gas injection, batching, ultra-pure water and of process variables in control systems.

Operation A volumetric device that measures the flow of both liquid and gases, the turbine flowmeter’s design is based on a freelysuspended turbine rotor which is rotated by the flow of fluid (liquid or gas) through the meter body.

FT Series Turbine Flowmeters

Features • High turndown capability, up to 100:1 • Excellent speed of response • Repeatability of ±0.05% (liquid) and ±0.1% (gas) of reading

• Linearity of ±0.5% of reading over normal 10:1 range for liquid, ±1% of full scale over the normal 10:1 range for gas

• Linearity of ±0.1% with linearizing electronics • Flow rates from 0.03 to 50,000 GPM (0.11 to 189,000 LPM) in liquid, 0.09 to 15,000 ACFM (2.55 to 424,800 ALPM) in gas

• Withstands pressures up to 400 BAR (5,800 psi), operation to 4,000 BAR (58,000 psi) optional

• Standard materials of construction are 316 SS housing and 430F SS rotor. Additional materials available

• End fittings available are NPT, AN (MS), Hose Barb, ANSI Flanges, SAE, Tri-clamp and special configurations as required

• High Shock meter designs available

FT Sizing BASED ON NORMAL RANGE

EXTENDED RANGE 5 DIGIT SERIES & SIZE

END FITTING NOMINAL INCHES

NORMAL FLOW RANGE 10:1

METER I.D. MM

INCHES

MIN

MAX

LIQUID

JOURNAL BEARINGS

NOMINAL K-FACTOR APPROX.

ALL

PICKOFFS

MIN

MAX

LPM

GPM

RF MIN

MAG MIN

RF MIN

MAG MIN

LPM

GPM

LPM

GPM

LPM

GPM

LPM

GPM

MAX. FREQ. APPROX.

ALL MAX LPM

GPM

P/L

P/G

Hz

FT 4-6

3/8

7.6

0.300

0.95

9.5 0.25

2.5

0.11

0.03

0.38

0.10

0.38

0.10

0.45

0.12

11

3 12680 48000

2000

FT 4-8

1/2

7.6

0.300

0.95

9.5 0.25

2.5

0.11

0.03

0.38

0.10

0.38

0.10

0.45

0.12

11

3 12680 48000

2000

FT 6-8

1/2

9.4

0.370

1.9

19

0.5

5.0

0.19

0.05

0.45

0.12

0.57

0.15

0.76

0.20

19

5

6600 25000

2100

FT 8-8

1/2

10

0.400

2.8

28 0.75

7.5

0.30

0.08

0.6

0.16

0.76

0.20

0.95

0.25

30

8

4200 16000

2000

FT-08

1/2

11

0.440

3.8

38

1.0

10.0

0.38

0.10

0.76

0.2

0.95

0.25

1.1

0.3

38

10

3170 12000

2000

FT-10

*5/8, 3/4

13

0.500

4.7

47 1.25

12.5

0.57

0.15

1.1

0.3

1.1

0.3

1.5

0.4

56

15

2540

9600

2000

FT-12

3/4

14

0.560

7.6

76

2.0

20

0.95

0.25

1.8

0.5

1.9

0.5

1.9

0.5

94

25

1580

6000

2000

FT-16

1

22

0.860

19

190

5.0

50

2.3

0.6

3.7

1.0

3.8

1.0

3.8

1.0

227

60

635

2400

2000

FT-20

1 1/4

25

1.00

34

340

9.0

90

3.8

1.0

5.6

1.5

3.8

1.0

5.7

1.5

378

100

345

1300

1950

FT-24

1 1/2

34

1.32

57

570

15

150

6.0

1.6

9.4

2.5

6.0

1.6

9.5

2.5

605

160

160

600

1500

FT-32

2

44

1.75

85

850

22

225

9.5

2.5

13

3.5

9.5

2.5

13

3.5

946

250

92

350

1300

FT-40

2 1/2

56

2.22

151

1510

40

400

17.0

4.5

19

5.0

17

4.5

19

5.0

1700

450

48

180

1200

FT-48

3

73

2.87

246

2460

65

650

N/A

28

7.5

N/A

28

7.5

2838

750

20

75

812

FT-64

4

98

3.87

473

4730

125

1250

N/A

57

15

N/A

57

15

5677 1500

8

30

625

FT-96

6

152

6.00

1135

11350

300

3000

N/A

190

50

N/A

190

50

13246 3500

7.5

28

1400

FT128

8

203

8.00

2082

20820

550

5500

N/A

227

60

N/A

227

60

22710 6000

3.7

14

1300

FT160

10

254

10.00

3217

32170

850

8500

N/A

378

100

N/A

378

100

37848 10000

2.2

8.5

1200

FT192

12

305

12.00

4542

45420 1200 12000

N/A

568

150

N/A

568

150

56772 15000

1.3

5.0

1000

ALPM

ACFM

FT 2-8

1/2

9.4

**0.370

2.83

FT 4-8

1/2

7.6

**0.300

7.0

FT 6-8

1/2

9.4

**0.370

14.0

140

FT 8-8

1/2

10

**0.400

FT-08

1/2

11

**0.440

FT-10

*5/8, 3/4

13

FT-12

3/4

14

FT-16

1

22

FT-20

1 1/4

25

1.00

255

2550

9

FT-24

1 1/2

34

1.32

425

4250

15

FT-32

2

44

1.75

623

6230

22

FT-40

2 1/2

56

2.22

1133

11330

FT-48

3

73

2.87

1841

FT-64

4

98

3.87

FT-96

6

152

6.00

FT128

8

FT160 FT192

ALPM

GAS

BALL BEARINGS

ALPM

ACFM

28.3

ACFM

ALPM

ACFM

1.0

2.55

0.09

N/A

N/A

N/A

35.5

1.25

3284 93000

70 0.25

2.5

5.7

0.2

N/A

N/A

N/A

85

3.0

1589 45000

2000

0.5

5.0

7.1

0.25

11.4

N/A

N/A

141.6

5.0

848 24000

2000

21.2

212 0.75

7.5

11.5

0.4

14.2

0.5

N/A

N/A

226.5

8.0

565 16000

2000

28.3

283

1.0

10

14.5

0.5

21.3

0.75

N/A

N/A

283

10

424 12000

2000

0.500

35.4

354 1.25

12.5

17

0.6

28.4

1.0

N/A

N/A

424

15

339

9600

2000

0.560

56.6

566

2

20

28.5

1.0

42.5

1.5

N/A

N/A

708

25

212

6000

2000

0.860 141.6

1416

5

50

42.5

1.5

71

2.5

N/A

N/A

1699

60

85

2400

2000

90

71

2.5

142

5

N/A

N/A

2832

100

46

1300

1950

150

114

4

170

6

N/A

N/A

4531

160

21

600

1500

220

142

5

228

8

N/A

N/A

7080

250

12

350

1300

40

400

255

9

284

10

N/A

N/A

12744

450

6.3

180

1200

18410

65

650

N/A

425

15

N/A

N/A

21240

750

3

75

812

3540

35400

125

1250

N/A

850

30

N/A

N/A

42480 1500

1

30

625

8496

84960

300

3000

N/A

1983

70

N/A

N/A

99120 3500

0.31

9.0

467

203

8.00 15576 155760

550

5500

N/A

3399

120

N/A

N/A

169920 6000

0.14

4.0

325

10

254

10.00 24072 240720

850

8500

N/A

5664

200

N/A

N/A

283200 10000

0.07

2.0

240

12

305

12.00 33984 339840 1200 12000

N/A

8496

300

N/A

N/A

424800 15000

0.035

1.0

167

Hose Barb

1550

*AN = 5/8" All Others = 3/4"

Blue = Metric (SI) Units

Black = English (US) Units

**0.440 bore when used with “H” bearing code

Metric units in LPM (liquid) & ALPM (gas)

English units in GPM (liquid) & ACFM (gas)

F

Tri-Clamp

P/Ft3

P/L

0.1

0.4

AN (MS)

Grayloc

T Series & Size

End Fittings

Abbreviations for Units of Measure: LPM = Liters per Minute GPM = Gallons per Minute

ALPM = Actual Liters per Minute ACFM = Actual Cubic Feet per Minute

P/L = Pulses per Liter P/G = Pulses per Gallon P/Ft 3 = Pulses per Cubic Foot

Calib

Model Numbering System Calibration End Fittings

AN (MS)

Tri-Clamp

NPT/BSP

ANSI/DIN Raised Face Flange

Hose Barb ANSI Ring t Flange

Grayloc

on bic Foot

AE = AN (or MS) external straight threads, 3/8" to 2 1/2" nominal size, 37° flare NE = NPT external threads, 1/2" to 4" nominal size HB = Hose Barb, 13 to 51 mm/ 1/2" to 2" BE = British Standard tapered pipe thread per BS21:1973, 1/2" to 4" BS = British Standard straight thread Thread per ISO 228-1, Sealing surface per DIN 3852, part 2, type A, 1/2" to 2" WF = Wafer type, serrated surface, 13 to 76 mm/1/2" to 3" nominal size C1 = 150# Raised Face Flange C2 = 300# Raised Face Flange C3 = 600# Raised Face Flange C4 = 900# Raised Face Flange C5 = 1500# Raised Face Flange C6 = 2500# Raised Face Flange J1 = 150# Ring t Flange J2 = 300# Ring t Flange J3 = 600# Ring t Flange J4 = 900# Ring t Flange J5 = 1500# Ring t Flange J6 = 2500# Ring t Flange G1 = 1/2", 1GR4 Grayloc, 900 BAR G2 = 3/4", 1GR7 Grayloc, 460 BAR G3 = 1", 1GR11 Grayloc, 227 BAR G5 = 1 1/2", 11/2GR14 Grayloc, 390 BAR G6 = 1 1/2", 2GR14 Grayloc, 600 BAR G7 = 2", 3GR25 Grayloc, 435 BAR G8 = 3", 3GR27 Grayloc, 225 BAR G9 = 3", 4GR25 Grayloc, 675 BAR

CODE Note:

DESCRIPTION A=Air, W=Water, S=Solvent, B=Oil Blend Viscosity must be provided with oil blend calibrations “B”

CODE

DESCRI

U2

NA NW NS NB

10 10 10 10

point, point, point, point,

normal normal normal normal

U3

Universa (specify m viscosity Universa (specify m viscosity

XA XW XS XB

10 10 10 10

point, point, point, point,

extended extended extended extended

TA TW TS TB

20 20 20 20

point, point, point, point,

normal normal normal normal

YA YW YS YB

20 20 20 20

point, point, point, point,

extended extended extended extended

range, range, range, range,

in in in in

air water solvent oil blend

FA FW FS FB

15 15 15 15

point, point, point, point,

extended extended extended extended

range, range, range, range,

in in in in

air water solvent oil blend

GA GW GS GB

30 30 30 30

point, point, point, point,

extended extended extended extended

range, range, range, range,

in in in in

air water solvent oil blend

10:1 10:1 10:1 10:1

range, range, range, range,

in in in in

air water solvent oil blend

BA range, range, range, range,

10:1 10:1 10:1 10:1

in in in in

range, range, range, range,

air water solvent oil blend in in in in

BW BS BB

air water solvent oil blend

CA CW CS CB

LW LS

Calibration

– = Standard R = Range U = Units B = Both



R1 R2 R3

10 points 10 points 10 points

E1 E2 E3

20 points 20 points 20 points

The third digit of the calibration designator is normally not used and occupied by a dash (–). When required, the following codes are used: U — To signify required units of measure other than GPM or ACFM R — To signify special calibration flow range other than normal 10:1 or extended range B — To signify both changes in units and special flow range

L = Liquid G = Gas P = Gas with Pressure Tap

Bi-direct sensing, Bi-direct sensing, Bi-direct sensing, Bi-direct sensing,

Specify Temp. &

Note: Additional Grayloc fittings available. Please factory with pressure and size specifications.

T1 = Tri-Clamp 1/2" to 3/4" T2 = Tri-Clamp 1" to 1 1/2" T3 = Tri-Clamp 2" T4 = Tri-Clamp 3" D1 = DIN Flange PN16 D2 = DIN Flange PN40 D3 = DIN Flange PN100 D4 = DIN Flange PN160 D5 = DIN Flange PN250 D6 = DIN Flange PN400

Bi-direct direction Bi-direct direction Bi-direct direction Bi-direct direction

Material

Materials of Construction MATERIAL CODE 1 D E G H N Q R T

PTION

al Viscosity Curve, 2 Viscosities minimum viscosity & maximum y). 10 points each viscosity al Viscosity Curve, 3 Viscosities minimum viscosity & maximum y). 10 points each viscosity

ional, 1 pickoff, , air ional, 1 pickoff, , water ional, 1 pickoff, , solvent ional, 1 pickoff, , oil blend

10 points each

ROTOR 17-4 PH SST 430F SST 316 SST 17-4 PH SST HAST C PVC MONEL-400 CARP 20 2

(Bearings offered with material code. See bearings below.)

A, D, G A, D, E, G, H D, E, G A, D, E, G, H E, G E, G D, E, G E, G

Material code “D” is for standard 6"/152 mm or larger. Rotor material other than 430F SST or 17-4 PH SST will require special handling in the form of a ferrous slugged rotor or special processing electronics. Please the factory for any further information.

1

10 points each

2

10 points each 10 points each

Bearings

ional, 2 pickoffs, direction 10 points each direction, air ional, 2 pickoffs, direction 10 points each direction, water ional, 2 pickoffs, direction 10 points each direction, solvent ional, 2 pickoffs, direction 10 points each direction, oil blend

Bearing selection will affect Flow Range. Refer to sizing specification table for correct Flow Ranges. A D E G H

m linearity, 10 point, 10:1 range, water m linearity, 10 point, 10:1 range, solvent Press., Min/Max, for Reynolds No. Cal.

s, 1 pressure, Reynolds No. Cal. s, 2 pressure, Reynolds No. Cal. s, 3 pressure, Reynolds No. Cal.

— — — — —

Ball Bearings (440 C) Carbide Journal (Carbide Shaft & Sleeve) liquid only Graphite Journal (Graphite Sleeve, 316 SST Shaft) liquid only Ceramic Journal (Ceramic Shaft & Sleeve) liquid only Ball Bearing (440 C Teflon Retainer) gas only (Offered on FT-64 and smaller)

Pickoffs The following is a listing of some of the pickoffs that are available from Flow Technology. –1 = Modulated Carrier, MS connector –2 = Magnetic, MS connector –3 = Magnetic, flying leads/threaded connection –5 = Modulated Carrier, flying leads/threaded connection –6 = Magnetic, MS connector, 400° C/750° F max –7 = Magnetic, flying leads/threaded connection 400° C/750° F max –L = Modulated Carrier, MS connector, 400° C/750° F max –M = Modulated Carrier, flying leads/threaded connection 400° C/750° F max –8 = Modulated Carrier, MS connector, 330 µH coil –9 = Modulated Carrier, MS connector, 5/8"–18 thread, 1mH coil –Y = Modulated Carrier, CSA X-Proof –Z = Magnetic, CSA X-Proof T1 = Modulated Carrier w/RTD, MS connector T2 = Magnetic w/RTD, MS connector T3 = Magnetic w/RTD, flying leads/threaded connection T5 = Modulated Carrier w/RTD, flying leads/threaded connection –X = Modulated Carrier, I.S. approved, MS connector SS = Modulated Carrier, I.S. approved, flying leads/smooth body XX = Modulated Carrier, I.S. approved, flying leads/threaded body –U = Magnetic, I.S. approved, MS connector PP = Magnetic, I.S. approved, flying leads/smooth body TT = Magnetic, I.S. approved, flying leads/threaded body Note: 1. Maximum temperature rating of pickoffs are 177° C (350° F) unless otherwise noted. 2. See Amplifier Link literature for amplified pickoff codes.

s, 1 pressure, Reynolds No. Cal. s, 2 pressure, Reynolds No. Cal. s, 3 pressure, Reynolds No. Cal.

Bearing

BEARING CODE HOUSING 304 SST 316 SST 316 SST 316 SST HAST C PVC MONEL-400 CARP 20

Pickoff

Optional Designators (Consult Factory)

Please note: Highlighted areas indicate standard base price configuration.

Dime

Operation (cont’d) An external pickoff senses the ing of each rotor blade, generating a frequency output. The frequency is directly proportional to the velocity of the fluid, and since the flow age is fixed, the turbine’s rotational speed is a true representation of the volumetric rate of fluid flowing through the flowmeter.

Specifications Applicable to Both Liquid and Gas Flowmeters Materials Of Construction Standard

316 SST Housing 430F SST Rotor 440 C Ball Bearings Stainless steel all other wetted parts

Other materials of construction optional (see model number chart). Operating Temp. Range

Defined by pickoff and bearing selection

Bearing Type Temperature Limits: 440 C stainless steel -450° F to 300° F ball bearings (-270° C to 150° C) Note: Not recommended for water service. Ceramic journal bearings

-100° F to 800° F (-75° C to 425° C)

Graphite journal bearings

-100° F to 550° F (-75° C to 290° C)

Tungsten carbide -100° F to 1,200° F journal bearings (-75° C to 650° C) Note: Journal bearings are for liquid service only.

Either a Magnetic or Modulated Carrier (RF) pickoff with a range extending amplifier can be used to sense the rotation of the turbine rotor and provide an electrical output that is proportional to the process flow rate. A benefit of the RF pickoff is that it extends the low flow range of the meter by eliminating magnetic drag on the rotor. The frequency output is processed by complementary electronics, ranging from basic amplifiers, indicators and totalizers, to more complex flow computers which compensate for all measurable process parameters and provide ultimate volumetric or mass flow measurement accuracy.

Series

mm FT-_8 FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96 FT128 FT160 FT192

127 140 140 140 152 152 165 178 254 305 356 406 508 610

Liquid Service Liquid service performance specifications are based on a viscosity of 1.2 centistokes using ball bearings. Calibration Accuracy

≤±0.05% of reading (accuracy of primary flow calibration standard directly traceable to NIST)

Repeatability

≤±0.05% of reading

Linearity

≤±0.5% of reading over the normal 10:1 flow range ( linearity of ±0.25% offered)

Series

A

mm FT-–8 FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96

48 49 49 64 64 64 76 133 146 127 155

±0.1% of reading with linearizing electronics Pressure Drop

Less than 700 mBAR (10 psid) at maximum 10:1 flow rate

Series

D

Temperature Limits: -430° F to 350° F (-260° C to 177° C) 10 mV min.

Dynamic Response

Less than 10 mS response to a step input change of flow rate

-430° F to 750° F (-260° C to 400° C) 10 mV min.

Gas Service

Modulated Carrier (RF)

-300° F to 350° F (-185° C to 177° C)

Gas service performance specifications are based on air at standard conditions 1 BAR and 20° C (14.7 psia and 68° F) with ball bearings.

High Temp. (RF)

Up to 750° F (400° C)

FT-–8 FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96 FT128 FT160 FT192

1 2 2 2 3 4 5 6 8 10 15 20 25 30

Pickoff Type Magnetic Output: High Temp. Magnetic Output:

Pickoff Electronic Connections MS Connector 2-pin, standard pickoff 15-89515-101 3-pin, amplified pickoff 15-89515-102 4-pin, pickoff with RTD 15-93825-01 Threaded Connection with Leads Junction Box with Terminal 73-31836-105 Operating Pressure Range

Defined by end connection rating up to 400 BAR (5,800 psi) standard. Special high pressure available up to 4,000 BAR (58,000 psi)

Filtration Recommendations Ball Bearings 10 micron to 100 micron (with less filtration for large sizes) Journal Bearings

100 micron

Calibration Accuracy

≤±0.3% of reading (accuracy of primary flow calibration standard directly traceable to NIST)

Repeatability

≤±0.1% of reading

Linearity

≤±1.0% of full scale over the normal 10:1 flow range ±0.1% of reading with linearizing electronics

Note: 1) 2) 3) 4)

Con All A NPT Waf

Specifications a

Pressure Drop

Pressure Tap

Less than 40 mBAR (16 inches of water) at normal 10:1 maximum flow rate Optional on all gas meters 7/16-2OUNJF-3A thread, MS33656, for flared 1/4" O.D. tube, AN806-4

Local R

Dimensions A

Series FT-_8 FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96 FT128 FT160 FT192

B

PICKOFF

A

150#

300#

mm

in.

mm

in.

mm

in.

mm

in.

mm

in.

5.0 5.5 5.5 5.5 6.0 6.0 6.5 7.0 10.0 12.0 14.0 16.0 20.0 24.0

89 99 99 108 118 127 152 178 191 229 279 343 406 483

3.5 3.88 3.88 4.25 4.63 5.0 6.0 7.0 7.5 9.0 11.0 13.5 16.0 19.0

127 140 140 140 152 152 165 178 254 305 356 406 508 610

5.0 5.5 5.5 5.5 6.0 6.0 6.5 7.0 10.0 12.0 14.0 16.0 20.0 24.0

95 118 118 124 133 156 165 191 210 254 318 381 445 521

3.75 4.63 4.63 4.88 5.25 6.13 6.5 7.5 8.25 10.0 12.5 15.0 17.5 20.5

127 140 140 140 152 152 165 229 254 305 356 406 508 610

5.0 5.5 5.5 5.5 6.0 6.0 6.5 9.0 10.0 12.0 14.0 16.0 20.0 24.0

FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96

Series

48 49 49 64 64 64 76 133 146 127 155

DN

B

A

in.

mm

in.

1.88 1.90 1.90 2.50 2.50 2.50 3.00 5.25 5.75 5.00 6.12

35 43 43 51 64 73 92 105 127 157 216

1.38 1.70 1.70 2.00 2.50 2.88 3.62 4.12 5.00 6.18 8.50

PN 16 A B mm

FT-–8 FT-10 FT-12 FT-16 FT-20 FT-24 FT-32 FT-40 FT-48 FT-64 FT-96 FT128 FT160 FT192

15 20 20 25 32 40 50 65 80 100 150 200 250 300

127 140 140 140 152 152 165 178 254 305 356 406 508 610

A

95 105 105 115 140 150 165 185 200 220 285 340 405 460

mm 62 69 83 90 103 117 154 164 244

B

mm

in.

mm

in.

mm

in.

95 3.75 118 4.63 118 4.63 124 4.88 133 5.25 156 6.13 165 6.5 191 7.5 210 8.25 273 10.75 356 14.0 419 16.5 508 20.0 559 22.0

178 140 178 203 203 229 229 229 254 305 356 406 508 610

7.0 5.5 7.0 8.0 8.0 9.0 9.0 9.0 10.0 12.0 14.0 16.0 20.0 24.0

121 130 130 149 159 178 216 241 241 292 381 470 546 610

4.75 5.13 5.13 5.88 6.25 7.0 8.5 9.5 9.5 11.5 15.0 18.5 21.5 24.0

B

J

M

in.

mm

in.

mm

in.

mm

in.

2.45 2.72 3.25 3.56 4.06 4.59 6.06 6.47 9.59

25 35 35 41 48 57 70 73 89

1.00 1.38 1.38 1.63 1.88 2.25 2.75 2.88 3.50

62.20 69.10 82.60 90.40 103.10 116.60 153.90 157.23 244.00

2.45 2.72 3.25 3.56 4.06 4.59 6.06 6.19 9.59

12.70 15.50 19.10 25.40 31.80 38.10 50.80 64.00 76.00

0.50 0.61 0.75 1.00 1.25 1.50 2.00 2.50 3.00

14.70 17.80 21.10 28.50 34.80 41.70 54.90 68.00 81.00

0.58 0.70 0.83 1.12 1.37 1.64 2.16 2.67 3.17

178 140 140 140 152 152 165 178 254 305 356 406 508 610

105 105 140 140 155 170 195 220 230 265 355 430 515 585

Composite drawing showing MS end connections on the upper portion of the flowmeter and NPT/BSP threads on the lower portion. Pickoff is a 2-pin MS connector.

PN 250 A B

PN 400 A B

mm

mm

mm 178 140 178 203 203 229 229 254 254 305 356 406 508 610

Hose Barb flowmeter with 2-pin MS connector pickoff.

2.0" MAX (50.8mm)

DIN FLANGED PN 40 PN 100 PN 160 A B A B A B 95 105 105 115 140 150 165 185 200 235 300 375 450 515

NPT A END-TO-END

PICKOFF

CONSULT FACTORY

127 140 140 140 152 152 165 178 254 305 356 406 508 610

FLOW

N

mm

mm

B FLATS

HOSE BARB

in.

mm

2.0" MAX (50.8mm)

THREADS PER MS33656

900#

AN OR MS NPT OR BSP EXTERNAL THREADS

A mm

FT-–8

B 600#

127 140 140 140 152 152 165 178 254 305 356 406 508 610

WAFER

Series

ANSI FLANGED B A

105 140 140 140 170 170 195 220 230 265 355 430 515 585

178 140 178 203 203 229 229 254 254 305 356 406 508 610

130 150 150 150 185 185 200 230 255 300 390 485 585 690

178 140 178 203 203 229 229 254 254 311 356 406 -

B DIA FLOW

145 180 180 180 220 220 235 290 305 370 475 585 -

0.02" (0.5mm) FACE-TO-FACE A±

FT Series flowmeter with wafer end connections. Pickoff with flying leads and a 1" NPT enclosure connection on FT-16 and larger.

DIN/ANSI RAISED FACE, FLAT FACE OR RING T FLANGE

PICKOFF

2.0" MAX (50.8mm) B DIA

Blue = Metric (SI) Units mm = millimeters Note: 1) 2) 3) 4)

Black = English (US) Units in. = inches

Consult factory for Grayloc end fitting dimensions. All ANSI flanged meters will have a 1" NPT spud around pickoff. NPT meters 2 1/2" and larger will have a 1" NPT spud around pickoff. Wafer meters 1" and larger will have a 1" NPT spud around pickoff.

Specifications and dimensions are for reference only and are subject to change without notice.

FLOW

0.06" (1.5mm) FACE-TO-FACE A±

FT Series flowmeter with flanged end connections. Pickoff with flying leads and a 1" NPT spud enclosure connection.

Local Representative:

4250 E. Broadway Road, Phoenix, Arizona 85040 USA Tel: (602) 437-1315 • Fax: (602) 437-4459 • Toll Free: 1-800-528-4225 E-mail: [email protected] • Web: www.ftimeters.com DB 62042 Rev G © 2002 FTI Flow Technology, Inc. Printed in USA