Dow Corning 795 6s6h1r

Product Information

Silicone Sealants Dow Corning® 795 Silicone Building Sealant FEATURES & BENEFITS  Suitable for most new construction and remedial sealing applications  Versatile – high performance structural glazing and weather sealing from a single product  Available in 16 standard colors; custom colors also available  Excellent weatherability – virtually unaffected by sunlight, rain, snow, ozone and temperature extremes of -40°F (-40°C) to 300°F (149°C)  Excellent unprimed adhesion to a wide variety of construction materials and building components, including anodized, alodined, most coated and many Kynar®1-painted aluminums2  Ease of application – ready to use as supplied  Ease of use – all-temperature gunnability, easy tooling and lowodor cure byproduct  Meets global standards (Americas, Asia and Europe)

Neutral, one-part silicone sealant APPLICATIONS    

Structural and nonstructural glazing Structural attachment of many systems stiffener applications Weather sealing of most common construction materials including glass, aluminum, steel, painted metal, EIFS, granite and other stone, concrete, brick and plastics

TYPICAL PROPERTIES Specification Writers: These values are not intended for use in preparing specifications. Please your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product. Test

Property

Unit

Result

hours

3

days

7–14

days

14–21

Inches (mm)

0.1 (2.54)

minutes

20–30

g/L

28

ASTM D 2240 Durometer Hardness, Shore A

points

35

ASTM C 794 Peel Strength

lb/in (kg/cm)

32 (5.7)

At 25% extension

psi (MPa)

45 (0.310)

At 50% extension

psi (MPa)

60 (0.414)

percent

± 50

As Supplied ASTM C 679 Tack-Free Time, 50% RH Curing Time at 50% RH

25οC

(77оF)

and

Full Adhesion ASTM C 639 Flow, Sag or Slump Working Time

COMPOSITION  One-part, neutral-cure, RTV silicone sealant

VOC Content As Cured-After 21 days at

25οC

(77οF)

and 50% RH

ASTM C 1135 Tension Adhesion Strength

ASTM C 719 t Movement Capability ASTM C 1248 Staining (granite, marble, lime- Stone, brick and concrete)

None

As Cured-After 21 days at 25οC (77οF) and 50% RH followed by 10,000 hours in a QUV weatherometer, ASTM G 53 ASTM C 1135 Tensile Adhesion Strength

1

Kynar is a trademark of Atofina Chemicals Inc. your local Dow Corning Sales Application Engineer for specifics.

2

1

At 25% extension

psi (MPa)

35 (0.241)

At 50% extension

psi (MPa)

50 (0.345)

Based on South Coast Air Quality Management District of California. Maximum VOC is listed both inclusive and exclusive of water and exempt compounds. For a VOC data sheet for a specific sealant color, please send your request to [email protected].

DESCRIPTION

COLORS

Dow Corning® 795 Silicone Building Sealant is a one-part, neutral-cure, architectural-grade sealant that easily extrudes in any weather and cures quickly at room temperature. This cold-applied, non-sagging silicone material cures to a medium- modulus silicone rubber upon exposure to atmospheric moisture. The cured sealant is durable and flexible enough to accommodate ±50 percent movement of original t dimension when installed in a properly designed weather seal t. In a properly designed structurally glazed t, the sealant is strong enough to glass and other materials under high wind load.

Dow Corning 795 Silicone Building Sealant is available in 16 colors: white, limestone, champagne, natural stone, gray, black, bronze, sandstone, adobe tan, dusty rose, rustic brick, blue spruce, anodized aluminum, and charcoal. Custom colors may be ordered to match virtually any substrate.

APPROVALS/ SPECIFICATIONS Dow Corning 795 Silicone Building Sealant meets the requirements of:  Federal Specification TT-S 001 543A (COM-NBS) Class A for silicone building sealants  Federal Specification TT-S00230C (COM-NBS) Class A for one- component building sealants  ASTM Specification C 920 Type S, Grade NS, Class 50, Use NT, G, A and O  ASTM Specification C 1184 for structural silicone sealants  Canadian Specification CAN219.13- M82

HANDLING PRECAUTIONS

HOW TO USE Please consult the Dow Corning Americas Technical Manual, Form No. 62-1112, for detailed information on state-of-the- art application methods and t design. Please your local Dow Corning Sales Application Engineer for specific advice. Preparation Clean all ts, removing all foreign matter and contaminants such as grease, oil, dust, water, frost, surface dirt, old sealants or glazing compounds and protective coatings.

PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE SAFETY DATA SHEET IS AVAILABLE ON THE DOW CORNING WEBSITE AT DOWCORNING.COM, OR FROM YOUR DOW CORNING SALES APPLICATION ENGINEER, OR DISTRIBUTOR, OR BY CALLING DOW CORNING CUSTOMER SERVICE.

USABLE LIFE AND STORAGE

Application Method Install backing material or t filler, setting blocks, spacer shims and tapes. Mask areas adjacent to ts to ensure neat sealant lines. Primer is generally not required on non-porous surfaces, but may be necessary for optimal sealing of certain porous surfaces. A test placement is always recommended. Apply Dow Corning 795 Silicone Building Sealant in a continuous operation using positive pressure. (The sealant can be applied using many types of air-operated guns and most types of bulk dispensing equipment.) Before a skin forms (typically within 15 minutes), tool the sealant with light pressure to spread the sealant against the backing material and t surfaces. Remove masking tape as soon as the bead is tooled.

When stored at or below 27°C (80°F), Dow Corning 795 Silicone Building Sealant has a shelf life of 12 months from the date of manufacture. Refer to product packaging for “Use By Date.”

PACKAGING INFORMATION Dow Corning 795 Silicone Building Sealant is supplied in 10.3-fl oz (305mL) disposable plastic cartridges that fit ordinary caulking guns, 20-fl oz (590- mL) sausages and 2- and 4.5-gal (7.5- and 1 7-L) bulk containers.

LIMITATIONS Dow Corning 795 Silicone Building Sealant should not be used:  In structural applications without prior review and approval by your local Dow Corning Sales Application Engineer  In below-grade applications  When surface temperatures exceed 50°C (122°F) during installation  On surfaces that are continuously immersed in water  On building materials that bleed oils, plasticizers or solvents that may affect adhesion

Dow Corning is a ed trademark of Dow Corning Corporation. We help you invent the future is a trademark of Dow Corning Corporation. XIAMETER is a ed trademark of Dow Corning Corporation. © 2000–2016 Dow Corning Corporation. All rights reserved.

2016, July 1 Form No. 61-885Q-01

2

 On frost-laden or wet surfaces  In totally confined ts (the sealant requires atmospheric moisture for cure)  If the sealant is intended to be painted (paints do not typically adhere to most silicone sealants)  To surfaces in direct with food or other food-grade applications This product is neither tested nor represented as suitable for medical or pharmaceutical uses.

HEALTH AND ENVIRONMENTAL INFORMATION To customers in their product safety needs, Dow Corning has an extensive Product Stewardship organization and a team of Product Safety and Regulatory Compliance (PS&RC) specialists available in each area.

product shown to be other than as warranted. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DOW CORNING SPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY. DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. We help you invent the future. dowcorning.com

For further information, please see our website, dowcorning.com or consult your local Dow Corning representative.

LIMITED WARRANTY INFORMATION – PLEASE READ CAREFULLY The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer’s tests to ensure that our products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent. Dow Corning’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any Dow Corning is a ed trademark of Dow Corning Corporation. We help you invent the future is a trademark of Dow Corning Corporation. XIAMETER is a ed trademark of Dow Corning Corporation. © 2000–2016 Dow Corning Corporation. All rights reserved.

2016, July 1 Form No. 61-885Q-01

3