Cateye Cordless 2 Manual 2t4911

E

INSTRUCTION MANUAL

A. Main Display (Speed) B. Wheel Circumference Mark C. Mode Symbol D. Mode Button E. Wheel Sensor Pulse Symbol F. Speed Scale Symbol G. Auto Mode Symbol

OPERATION FEATURES Two buttons are provided on the top of the main unit and two on the bottom. These buttons are used as follows:

magnet triangle mark SENSO R ZONE

•Mode Button (top left button) Fig.1

Whenever this button is pressed, the mode display changes in the order shown in fig.1, and the data is displayed on the sub-display. Note: If this button is kept pressed for more than 2 seconds, display appears.

Fig.17

Reset

L

Fig.3

Measurement of trip distance, elapsed time and average speed is started or stopped when the start/stop button is pressed. Whenever this button is pressed, start and stop are repeated. During measurement the speed scale symbol blinks. Note: This button does not function if the auto mode function is set to ON [Refer to the explanation of the Auto (Automatic Start/Stop) Function below].

•Set Button (bottom left button) • To set the wheel circumference: Stop the measurement in the (O) mode, then press the SET button. • To set the 24-hour clock time: Stop the measurement in ( ) mode, then press the SET button. • To set auto mode to ON or OFF: Select the (T),(A) or (D) mode, then press the SET button.

Fig.4

•AC (All Clear) Button (bottom right button)

A

When this button is pressed, all the data stored in memory is cleared. After all displays illuminate, the "mile/h" symbol illuminates. This button should be pressed only after replacing the battery or when irregular display of information occurs due to static electricity,etc. Once this button is pressed and all memory is erased, it will be necessary to set the wheel circumference, time, etc. again. (refer to Main Unit Preparation)

Fig.5

B

Fig.6

Reset Operation: (Fig.2) A

AT

Press left button to select any mode except total distance (O) and press left and right buttons together. Stored data of trip distance (D), elapsed time (T), average speed (A) and maximum speed (M) are all reset to zero. (In the total distance display mode, the current wheel circumference (A) or (B) is shown.)

sensor zone

less than 5mm sensor zone

•Start/Stop Button (top right button) Fig.2

magnet

spoke Fig.18

Fig.19

OPEN

Fig.7

Fig.20

How to replace battery in Main Unit (Fig.20) Open the battery cover on the back and insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side of the battery against the . Press AC button to erase all stored data and then redo the settings.

CLOSE OPEN

CR2032

rubber pad

Fig.9

lever

Fig.10

When the AC button is pressed and all displays illuminate then the "mile/h" appears as shown in fig.4. "km/h" and "mile/h" are displayed alternatively each time the right button is pressed. Select any speed scale as desired and press SET button to complete the setting.



Fig.21

DISPLAY FUNCTIONS S Current Speed 0.0(3.0) to 65.9 miles/hr ±0.3mile/h This is always displayed on the main display and updated once a second.

A

D

0.0 to 99,999 miles ±0.1mile This is continuously measured until battery wears down or all clear operation is done. At 100,000 miles(km), it returns to zero and counting begins anew.

O Total Distance A

O

D Trip Distance

0.00 to 999.99 miles 0.01mile The trip distance from start to current point is displayed. With Reset operation, it returns to zero.

3. Setting the Wheel Circumference (Fig.5.6)

This cyclocomputer is able to memorize two different wheel circumferences. To remove One main unit can be used on two bicycles subject to buy another set of bracket and sensor. push Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set before the cyclocomputer left our factory. The (A) wheel circumference 2155mm (standard for 27 inch tire) will blink as shown in fig.5. If you want to enter pull 2155mm and 2030mm, simply press the SET button. If you want to change, press either the right button to increase or left button to decrease the number. slide To change the number rapidly keep the button pressed. Once you reach the setting you want, press the SET button. If you want to set a second circumference, press the left and right buttons together before pressing the SET button. front The wheel circumference 2030mm is displayed and blinks(fig.6). Set to a desired wheel circumference in the same manner as the first circumference setting and press SET button to complete the setting.

A

D

T Elapsed Time 0:00'00" to 9:59'59" ±0.003% Elapsed time is measured from start to current point, in units of hours, minutes and seconds. At 10 hours, it returns to zero and counting begins anew. With Reset operation, it returns to zero. A Average Speed 0.0 to 65.9 miles/hr ±0.3mile/h The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded, (.E) is displayed and calculation ceases. M Maximum Speed 0.0 (3.0) to 65.9 miles/hr ±0.3mile/h With Reset operation, it returns to zero and counting begins anew.

A

T

A

A

A

M

24 hr. Clock Time

4. Selecting one of the two Wheel Circumference (Fig.7) front fork

magnet Fig.11

sensor

Set the Auto Mode to ON. (Refer to the explanation of Auto Mode function.) While keeping the right button pressed , press the SET button. The first wheel circumference measurement will be displayed for a few seconds, then the second setting will appear.

sensor band A Fig.12 sensor band B rubber pad sensor band A parallel Fig.13

Press left button for more than 2 seconds to select the 24-hour clock display. Stop the measurement by pressing the right button. Press SET button and the minute display will start to blink. Press right button to select a minute time ahead of the current time by 1 to 2 minutes. Next press left button and the hour will blink. Press right button to set to current hour time. Press SET button to complete the setting.

Mount the sensor in the highest possible position on the right front fork leg. Adjust the position, clearance and direction as follows: screw (1) Insert the band B into the slit of the band A, and put the rubber pad inside of the band A (fig. 12). Adjust the length of the bands in order that the front fork sensor screw-fastening part of the bands is parallel when mounted to the fork (fig. Fig.14 13). * To pull out the band B from band A, tug strongly. long screw spacer (2) Mount the adjusted bands to fork along with the sensor, by temporarily tightening the screw (fig. 14).If the space between front fork and spoke of your bike is big, use the spacer and long screw as in the fig.15, so that the clearance between sensor and magnet will be approx. 5mm. (3) Attach the magnet securely to the right side of the spoke (fig. 16) so that the magnet properly faces the sensor zone (fig. 17). In case of (4) A 5mm clearance shall be kept between the sensor and magnet(fig.18). aerofork Then align the magnet with sensor zone (fig.16). Meanwhile, the sensor Attachment for aerofork shall aim at the main unit indicated by the triangle marked on the sensor. Fig.15 Then tighten the screw to secure the sensor in position. Cut the excess spoke sensor band B with scissors or the like.

Check points for sensor mounting:

fixing nut magnet

When the main unit is left without receiving any signal for one hour, the power will be turned off automatically. Resulting in SLEEP state in which only the 24-hour clock displays. The main unit can not receive any signal in this state. Press left or right button to restore signal reception. Note: to restore signal reception before every journey.

A

AUTO (AUTOMATIC START/STOP) FUNCTION The Cordless 2 is equipped with a selective auto function allowing automatic start or stop of measurement without using the right button. A

AT

T

MOUNTING TO BIKE Attach the bracket near handlebar stem, using rubber pad (fig. 9). Cut and adjust the length of the rubber pad if necessary. • Slide the main unit onto the bracket from front until it clicks into position. To remove the main unit, pull it forward while depressing the lever on bracket (fig.10).

How to Mount the Sensor on the Right Front Fork Leg.(fig.11)

Fig.16

POWER SAVING FUNCTION

5. How to reset the Wheel Circumference

Setting the 24-hour Clock (Fig.8)

1. Keep a 5 mm clearance between the sensor and magnet. 2. The magnet surface shall align to the sensor zone. 3. The triangle mark on the sensor shall aim at the main unit.

0:00´ to 23:59´ ±0.003%

The current time is displayed by a 24-hour clock.

A

Select the (O) mode and stop the measurement. Press SET button and the already set wheel circumference will blink on the sub-display. Refer to '3.Setting the wheel circumference' to complete the setting.

sensor band B rubber pad

How to replace battery in Sensor (Fig.21) Take off the sensor from the bicycle. Open the battery cover on the back and insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side of the battery against the . Mount the sensor back to the bicycle and adjust to relative position, clearance and direction.

2. Setting the Speed Scale (Fig.4) bracket

THE CORDLESS SYSTEM

REPLACING THE BATTERIES

1. How to measure the exact Wheel Circumference (L)(Fig.3)

Fig.8

TEST Mount the main unit on the bracket. If current speed doesn't appear on the main display, press either left or right button to release the unit from the power saving mode. Then spin the front wheel to make sure the wheel sensor pulse symbol flickers. If it does not flicker, adjust the position of sensor until it flickers normally. The mounting is completed and the cyclocomputer is operational.

Batteries are already loaded in the main unit and the sensor.

must make the following setting according to instructions before the cyclocomputer can be used properly. First, adjust tire pressure and then put a mark on the tire tread and the ground simultaneously. Then ride the bike one full wheel revolution. Mark the ground at the end of one revolution and then measure the distance between the two marks. This measure is your actual wheel circumference. Or, the "Setting Values Cross Reference Table" can help you to find out an approximate wheel circumference according to tire size.

7. Screw 8. Long Screw 9. Spacer 10.Attachment for aerofork 11.Nylon Tie

The sensor picks up wheel revolution signal and transmits the signal to the receiver in the main unit. The main unit receives, calculates and displays the data. The approximate service hour of batteries is as follows: The main unit (receiver): --- Approx. 2 years (average 1 hour's use per day) The sensor (transmitter): ------- Total distance of approx. 10,000 miles (16,000 km) Note: To prevent external signal interference, the sensor signal reception range is restricted. For best performance, the triangle mark on the sensor shall sensor aim at the direction to the main unit. The distance between the sensor and main unit must be kept within 70 cm. The signal reception range may shorten as a result of low ambient temperature or lowered battery power. It is advisable to replace the sensor battery before it fails. The battery service hours quoted above is the average for a 65 cm distance between the sensor and main unit. • The cordless system may be interfered with in the following situation, so that main unit may display false data. CLOSE 1. Riding near railroad crossings and trains. 2. Riding in places where intensive electromagnetic wave or field exist, such as TV transmission station and radar installations. CR2032 3. When two bicycles carrying similar cyclocomputers are ridden side by side.

MAIN UNIT PREPARATION B AT

1. Bracket 2. Sensor(Transmitter) 3. Sensor Band A 4. Sensor Band B 5. Magnet 6. Rubber Pad

H. Sub-Display (Selected function) I. Start/Stop Button J. Battery Case Cover K. Set Button L. AC Button

How to Set On/Off the Auto Function Select (T), (D) or (A) to sub-display and then press SET button. The AT symbol will display when auto function is set ON. Repeat to set OFF the auto function. Note: In SLEEP state, auto start will not function. Press left or right button to restore signal reception first. (Refer to Power Saving Function)

MAINTENANCE/PRECAUTIONS • Do not leave the main unit exposed to direct sunlight when the unit is not in use. Do not disassemble the main unit. • Don't pay too much attention to your computer's functions while riding! Keep your eyes on the road and give due consideration to traffic safety. • Check the relative position of magnet and sensor periodically. • For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply paint thinner, benzine, or alcohol, which may damage on the surface.

TROUBLE SHOOTING No display. ------------------------------------------------------ Replace the main unit battery with new one. Incorrect data appears. -------------------------------------- Execute "All Clear" operation. Figures do not appear on the main display ------------- Cancel the power saving function. Current speed does not appear. --------------------------- Check the sensor position and direction. Speed is not displayed when riding with high speed or at low temperature. --------------------------------------------------------------------- Check the sensor position and direction. --------------------------------------------------------------------- Has the battery worn out? Even when the right button is pressed, the cyclocomputer does not operate. --------------------------------------------------------------------- Set the auto mode to OFF. The entire liquid crystal screen is dark and unusual display is seen where it should not be. --------------------------------------------------------------------- It returns to normal state if left in the shade. Display response is slow. ----------------------------------- It returns to normal state when temperature rises.

SPECIFICATIONS Applicable Cycle Sizes Power Supply

10 mm - 2,999 mm(Initial value: A:2155 mm B:2030 mm) Main unit: ------------------------------------ Lithium Battery (CR2032)x1/approx. 2years Sensor with transmitter: ------------------ Lithium Battery (CR2032)x1/approx. 1,000miles Dimension / Weight 2"x 1-13/10"x 29/32" / 1.2 oz (29 g) * The specifications and design are subject to change without notice.

CYCLOCOMPUTER Model CC-CL200N

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Modifications ®

The FCC requires the to be notified that any changes or modifications made to this device that are not expressly approved by Cat Eye Co., Ltd. may void the ’s authority to operate the equipment.

US. PAT. NO.4633216, 4636769, 4642606, 5236759 and Patent Pending Design Patented Copyright© Aug. 2001 CAT EYE Co., Ltd. CCMCL2-010402

1

Specifications/Caracteristiques techniques/Technische daten/Specificaties/ Caratteristiche tecniche/Especificaciones

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.) Table de Correspondance des Valeurs de Réglage (La dimension du pneu figure de chaque côté du pneu) Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens) Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band) Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico) Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta) TIRE SIZE L(mm) dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda 24 x 1 1753 24 x 3/4 Tubular 1785 24 x 1-1/8 Tubular 1795 24 x 1-1/4 1905 24 x 1.75 1890 24 x 2.00 1925 24 x 2.125 1965 26 x 1(559mm) 1913 26 x 1(650c) 1952 26 x 1.25 1953 26 x 1-1/8 Tubular 1970 26 x 1-3/8 2068 26 x 1-1/2 2100 26 x 1.40 2005

TIRE SIZE L(mm) dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda 26 x 1.50 1985 26 x 1.75 2030 26 x 1.95 2050 26 x 2.00 2055 26 x 2.1 2068 26 x 2.125 2070 26 x 2.35 2083 27 x 1 2145 27 x 1-1/8 2155 27 x 1-1/4 2161 27 x 1-3/8 2169 650 x 35A 2090 650 x 38A 2125 650 x 38B 2105

TIRE SIZE L(mm) dimension du pneu Radgröße bandenmaat dimensione del pneumatico Tamaño de rueda 700 x 18C 2070 700 x 19C 2090 700 x 20C 2086 700 x 23C 2096 700 x 25C 2105 700 x 28C 2136 700 x 30C 2170 700 x 32C 2155 700C Tubular 2130 700 x 35C 2168 700 x 38C 2180 700 x 44C 2224

Controller/Calculateur/Controler/Controleur/Elaboratore/Contador -------------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator) Display/Affichage/Anzeige/Display/Visualizzazione/Pantalla ------------------------------------------------------------------------------------ Liquid Crystal Display Sensor/Détecteur/Sensor/Sensor/Rivelatore/Sensor --------------------------------------------------------------------------- No Contakt Magnetic Sensor Cordless Système/System sans fil/Kabelloses System/Draadloze systeem/Sistema sin hilos/Sistema cordless ---------------------------------------------------------------- Directional electromagnetic induction Operating Temperature Range/Température d’utilisation/zulässige Betriebstemperatur/Toegestane temp./Temperatura di utilizzo -------------------------------------------------------------------------------- 0°C - 40°C(32°F - 104°F)

LIMITED WARRANTY 2-Year Warranty: Only Main Unit/Sensor If trouble occurs during normal use, the part is repaired or replaced free of charge. The service must be performed by CAT EYE Co., Ltd.. and the product needs service must be returned to CAT EYE Co., Ltd. directly by purchaser. When returning the product for CAT EYE warranty service, pack it very carefully, and enclose the warranty certificate and instructions for repair. Please make sure to write or type your name and address clearly on the warranty certificate, so that the product can be shipped back to you as soon as the necessary repair/adjustment is completed. Insurance, handling and transportation charges to our service shall be borne by person desiring service. CO.,LTD. Address for service 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn.: CAT EYE Customer Service Section Service & Research Address for United States Consumers: CAT EYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303-443-4595 Toll Free: 800-5CATEYE Fax: 303-473-0006 e-mail: [email protected]

GARANTIE LIMITEE Garantie de 2 ans : Unité Principale / Détecteur uniquement En cas de problème en cours d'utilisation normale, le produit sera réparé ou remplacé gratuitement. Les réparations doivent être effectuées par CAT EYE Co., Ltd. et le produit à réparer doit être retourné à CAT EYE Co., Ltd. directement par l'acheteur. Tout produit retourné au service de réparation CAT EYE doit être soigneusement emballé et le certificat de garantie ainsi que les instructions de réparation doivent accompagner le produit à réparer. Il est conseillé à l'acheteur d'écrire lisiblement ou de dactylographier ses nom et adresse sur le certificat de garantie, afin que le produit puisse lui être directement retourné dès que les réparations/réglages nécessaires sont terminés. Le coût de l'assurance ainsi que les frais de manutention et de transport vers le service de réparation CAT EYE sont à charge de la personne souhaitant une réparation sous garantie.

#169-6690N

Adresse d'envoi pour réparation

Parts Kit Kit d'accessoires Ersatzteil Onderdelen set Kit d'accessori Kit de piezas

CO.,LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japon. Attn : CAT EYE Customer Service Section.

BEGRENZTE GARANTIE 2-Jahres-Garantie: Auf den Computer und den Sensor Falls während des normalen Gebrauchs Fehler auftreten, wird das entsprechende Teil kostenlos repariert oder ersetzt. Die Reparatur muß von CAT EYE Co., Ltd. durchgeführt werden, und das zu reparierende Produkt muß direkt durch den Händler an CAT EYE Co., Ltd. gesandt werden. Bei der Rückgabe des Gerätes zur Reparatur packen Sie es sorgfältig anbei. Achten Sie darauf, Ihren Namen und Ihre Anschrift klar und deutlich lesbar auf die Garantiekarte zu schreiben, damit das Gerät so schnell wie möglich nach Beendigung der notwendigen Reparatur/Einstellung an Sie zurückgesandt werden kann. CO.,LTD. Anschrift bei Garantieansprüchen 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan z. H.: CAT EYE Kundendienstabteilung oder wenden Sie sich bitte an den entsprechenden Importeur.

#169-6660N Bracket Kit Kit d'unite principale Halterung Bracketkit Kit o Soporte

#169-6670N Cordless Sensor Palpeur (Emetteur) Sensor mit Sender Sensor-draadloos Sensore"Senzafilo" Sensor sin cable

GARANTIEBEPALINGEN

#169-9780

#169-6680

Attachment for aerofork Fixation pour fourche AERO Zusatz zur Federgabel Bevestiging voor aerovork Attacco per forcella aerodinamica Sujección para horquilla aerodinámica

Universal Sensor Band Collier Universel de Détecteur Universalsensorband Universele Sensorband Fascetta Universale di sensore Banda universal del sensor

Garantie: 2 jaar op computer en sensor Mochten er problemen optreden gedurende normaal gebruik, dan geschiedt reparatie of vervanging kosteloos. Dit dient door de fabrikant Cateye Co., Ltd. uitgevoerd te worden. De computer moet door de importeur aan Cateye Co., Ltd. teruggezonden worden. Bij terugzending van de computer moet deze zorgvuldig verpakt worden en dient het garantiebewijs, de aankoopbon en een beschrijving van het probleem meegezonden te worden. Vermeldt duidelijk uw naam en adres in blokletter of met de schrijfmachine op het garantiebewijs, zodat de computer in goede orde terruggestuurd kan worden.Verzekerings-, verzend- en transportkosten zijn voor rekening van de koper. CO.,LTD. Adres: 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Ter attentie van: Cateye klantenservice Zogauw als de reparatie/vervanging geschiedt is, wordt de computer aan u geretourneerd.

LIMITAZIONE DELLA GARANZIA

#169-6667

Garanzia di due anni Questo prodotto CATEYE è garantito con la riserva di una utilizzazione corretta, contro ogni difetto di fabbrica e di materiale. Le riparazioni effettuate nel quadro della presente garanzia sono gratuite a condizione che siano rispettate le seguenti disposizioni. Il costo dell'assicurazione come le spese di stoccaggio e di trasposrto sono a carico di chi richiede la riparazione. Questa garanzia è limitata alla riparazione dell'unità principale esclusi il filo, il o e qualsiasi accessorio. Si prega il compratore di scrivere chiaramente il proprio Cognome Nome ed indirizzo sul Certificato di garanzia completandolo in tutte le sue parti (Rivenditore/Data di acquisto etc.). CO.,LTD. Indirizzo per la rispedizione per riparazione 2-8-25, Kuwazu, Higashi-Sumiyoshi-ku, Osaka 546-0041, Giappone. Att.: Dipartamento Assistenza Clienti TEL.: 81-6-6719-7781 FAX: 81-6-6719-2362

Center Mount Bracket Kit Kit de montage central del l´unité principale Halterung für Montage en der Lenkermitte Stuurbocht Bevestinging Set Kit di Montaggio al Centro del manubrio Kit Soporte para Montaje Central

#169-6669 Stem Mount Bracket Kit Kit de montage de l´unité principale sur la broche du guidon Halterung für Montage en der Lenkerstange Stuurpen Bevestiging Set Kit di Montaggio sull´ attacco manubrio Kit Soporte para Montaje en Tija

GARANTÍA LIMITADA.

#169-9691

#166-5150

Wheel Magnet Aimant pour roue Ragnet Wielmagneet Magnete ruota Iman de la rueda

Lithium Battery (CR2032) Pile au lithium (CR2032) Lithium-Batterie (CR2032) Lithium Batterij (CR2032) Batteria al Litio (CR2032) Bateria de Litio (CR2032)

2 Años de Garantía: Sólo Unidad Principal/Sensor. Si sucedieran problemas durante un uso normal, la pieza será reparada o reemplazada gratuitamente. El servicio debe ser realizado por CATEYE CO., LTD. y el producto que necesite del servicio debe ser devuelto a CATEYE directamente por el comprador. Cuando se envíe el producto al servicio de garantía de CATEYE se ha de empaquetar muy cuidadosamente y adjuntar el certificado de garantía e instrucciones para la reparación. Por favor, asegúrese de escribir claramente su nombre y dirección en el certificado de garantía, con objeto de que el producto le sea devuelto a Vd. tan pronto como la reparación o ajuste necesario haya sido efectuado. Los gastos del seguro, manejo y transporte hasta nuestro servicio serán a cargo de la persona demandante de servicio. CO.,LTD. Para reparación enviar a: 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn.: CAT EYE Customer Service Section